]> Git Repo - J-linux.git/blob - drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
Merge tag 'vfs-6.13-rc7.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
[J-linux.git] / drivers / net / ethernet / intel / ixgbe / ixgbe_common.c
1 // SPDX-License-Identifier: GPL-2.0
2 /* Copyright(c) 1999 - 2018 Intel Corporation. */
3
4 #include <linux/pci.h>
5 #include <linux/delay.h>
6 #include <linux/sched.h>
7 #include <linux/netdevice.h>
8
9 #include "ixgbe.h"
10 #include "ixgbe_common.h"
11 #include "ixgbe_phy.h"
12
13 static int ixgbe_acquire_eeprom(struct ixgbe_hw *hw);
14 static int ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw);
15 static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw);
16 static int ixgbe_ready_eeprom(struct ixgbe_hw *hw);
17 static void ixgbe_standby_eeprom(struct ixgbe_hw *hw);
18 static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
19                                         u16 count);
20 static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count);
21 static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
22 static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
23 static void ixgbe_release_eeprom(struct ixgbe_hw *hw);
24
25 static int ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr);
26 static int ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg);
27 static int ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
28                                              u16 words, u16 *data);
29 static int ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
30                                               u16 words, u16 *data);
31 static int ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
32                                                  u16 offset);
33 static int ixgbe_disable_pcie_primary(struct ixgbe_hw *hw);
34
35 /* Base table for registers values that change by MAC */
36 const u32 ixgbe_mvals_8259X[IXGBE_MVALS_IDX_LIMIT] = {
37         IXGBE_MVALS_INIT(8259X)
38 };
39
40 /**
41  *  ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
42  *  control
43  *  @hw: pointer to hardware structure
44  *
45  *  There are several phys that do not support autoneg flow control. This
46  *  function check the device id to see if the associated phy supports
47  *  autoneg flow control.
48  **/
49 bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
50 {
51         bool supported = false;
52         ixgbe_link_speed speed;
53         bool link_up;
54
55         switch (hw->phy.media_type) {
56         case ixgbe_media_type_fiber:
57                 /* flow control autoneg black list */
58                 switch (hw->device_id) {
59                 case IXGBE_DEV_ID_X550EM_A_SFP:
60                 case IXGBE_DEV_ID_X550EM_A_SFP_N:
61                         supported = false;
62                         break;
63                 default:
64                         hw->mac.ops.check_link(hw, &speed, &link_up, false);
65                         /* if link is down, assume supported */
66                         if (link_up)
67                                 supported = speed == IXGBE_LINK_SPEED_1GB_FULL;
68                         else
69                                 supported = true;
70                 }
71
72                 break;
73         case ixgbe_media_type_backplane:
74                 if (hw->device_id == IXGBE_DEV_ID_X550EM_X_XFI)
75                         supported = false;
76                 else
77                         supported = true;
78                 break;
79         case ixgbe_media_type_copper:
80                 /* only some copper devices support flow control autoneg */
81                 switch (hw->device_id) {
82                 case IXGBE_DEV_ID_82599_T3_LOM:
83                 case IXGBE_DEV_ID_X540T:
84                 case IXGBE_DEV_ID_X540T1:
85                 case IXGBE_DEV_ID_X550T:
86                 case IXGBE_DEV_ID_X550T1:
87                 case IXGBE_DEV_ID_X550EM_X_10G_T:
88                 case IXGBE_DEV_ID_X550EM_A_10G_T:
89                 case IXGBE_DEV_ID_X550EM_A_1G_T:
90                 case IXGBE_DEV_ID_X550EM_A_1G_T_L:
91                         supported = true;
92                         break;
93                 default:
94                         break;
95                 }
96                 break;
97         default:
98                 break;
99         }
100
101         if (!supported)
102                 hw_dbg(hw, "Device %x does not support flow control autoneg\n",
103                        hw->device_id);
104
105         return supported;
106 }
107
108 /**
109  *  ixgbe_setup_fc_generic - Set up flow control
110  *  @hw: pointer to hardware structure
111  *
112  *  Called at init time to set up flow control.
113  **/
114 int ixgbe_setup_fc_generic(struct ixgbe_hw *hw)
115 {
116         u32 reg = 0, reg_bp = 0;
117         bool locked = false;
118         int ret_val = 0;
119         u16 reg_cu = 0;
120
121         /*
122          * Validate the requested mode.  Strict IEEE mode does not allow
123          * ixgbe_fc_rx_pause because it will cause us to fail at UNH.
124          */
125         if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
126                 hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
127                 return -EINVAL;
128         }
129
130         /*
131          * 10gig parts do not have a word in the EEPROM to determine the
132          * default flow control setting, so we explicitly set it to full.
133          */
134         if (hw->fc.requested_mode == ixgbe_fc_default)
135                 hw->fc.requested_mode = ixgbe_fc_full;
136
137         /*
138          * Set up the 1G and 10G flow control advertisement registers so the
139          * HW will be able to do fc autoneg once the cable is plugged in.  If
140          * we link at 10G, the 1G advertisement is harmless and vice versa.
141          */
142         switch (hw->phy.media_type) {
143         case ixgbe_media_type_backplane:
144                 /* some MAC's need RMW protection on AUTOC */
145                 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &reg_bp);
146                 if (ret_val)
147                         return ret_val;
148
149                 fallthrough; /* only backplane uses autoc */
150         case ixgbe_media_type_fiber:
151                 reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
152
153                 break;
154         case ixgbe_media_type_copper:
155                 hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
156                                         MDIO_MMD_AN, &reg_cu);
157                 break;
158         default:
159                 break;
160         }
161
162         /*
163          * The possible values of fc.requested_mode are:
164          * 0: Flow control is completely disabled
165          * 1: Rx flow control is enabled (we can receive pause frames,
166          *    but not send pause frames).
167          * 2: Tx flow control is enabled (we can send pause frames but
168          *    we do not support receiving pause frames).
169          * 3: Both Rx and Tx flow control (symmetric) are enabled.
170          * other: Invalid.
171          */
172         switch (hw->fc.requested_mode) {
173         case ixgbe_fc_none:
174                 /* Flow control completely disabled by software override. */
175                 reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
176                 if (hw->phy.media_type == ixgbe_media_type_backplane)
177                         reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE |
178                                     IXGBE_AUTOC_ASM_PAUSE);
179                 else if (hw->phy.media_type == ixgbe_media_type_copper)
180                         reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
181                 break;
182         case ixgbe_fc_tx_pause:
183                 /*
184                  * Tx Flow control is enabled, and Rx Flow control is
185                  * disabled by software override.
186                  */
187                 reg |= IXGBE_PCS1GANA_ASM_PAUSE;
188                 reg &= ~IXGBE_PCS1GANA_SYM_PAUSE;
189                 if (hw->phy.media_type == ixgbe_media_type_backplane) {
190                         reg_bp |= IXGBE_AUTOC_ASM_PAUSE;
191                         reg_bp &= ~IXGBE_AUTOC_SYM_PAUSE;
192                 } else if (hw->phy.media_type == ixgbe_media_type_copper) {
193                         reg_cu |= IXGBE_TAF_ASM_PAUSE;
194                         reg_cu &= ~IXGBE_TAF_SYM_PAUSE;
195                 }
196                 break;
197         case ixgbe_fc_rx_pause:
198                 /*
199                  * Rx Flow control is enabled and Tx Flow control is
200                  * disabled by software override. Since there really
201                  * isn't a way to advertise that we are capable of RX
202                  * Pause ONLY, we will advertise that we support both
203                  * symmetric and asymmetric Rx PAUSE, as such we fall
204                  * through to the fc_full statement.  Later, we will
205                  * disable the adapter's ability to send PAUSE frames.
206                  */
207         case ixgbe_fc_full:
208                 /* Flow control (both Rx and Tx) is enabled by SW override. */
209                 reg |= IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE;
210                 if (hw->phy.media_type == ixgbe_media_type_backplane)
211                         reg_bp |= IXGBE_AUTOC_SYM_PAUSE |
212                                   IXGBE_AUTOC_ASM_PAUSE;
213                 else if (hw->phy.media_type == ixgbe_media_type_copper)
214                         reg_cu |= IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE;
215                 break;
216         default:
217                 hw_dbg(hw, "Flow control param set incorrectly\n");
218                 return -EIO;
219         }
220
221         if (hw->mac.type != ixgbe_mac_X540) {
222                 /*
223                  * Enable auto-negotiation between the MAC & PHY;
224                  * the MAC will advertise clause 37 flow control.
225                  */
226                 IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
227                 reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
228
229                 /* Disable AN timeout */
230                 if (hw->fc.strict_ieee)
231                         reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
232
233                 IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
234                 hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
235         }
236
237         /*
238          * AUTOC restart handles negotiation of 1G and 10G on backplane
239          * and copper. There is no need to set the PCS1GCTL register.
240          *
241          */
242         if (hw->phy.media_type == ixgbe_media_type_backplane) {
243                 /* Need the SW/FW semaphore around AUTOC writes if 82599 and
244                  * LESM is on, likewise reset_pipeline requries the lock as
245                  * it also writes AUTOC.
246                  */
247                 ret_val = hw->mac.ops.prot_autoc_write(hw, reg_bp, locked);
248                 if (ret_val)
249                         return ret_val;
250
251         } else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
252                    ixgbe_device_supports_autoneg_fc(hw)) {
253                 hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
254                                       MDIO_MMD_AN, reg_cu);
255         }
256
257         hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
258         return ret_val;
259 }
260
261 /**
262  *  ixgbe_start_hw_generic - Prepare hardware for Tx/Rx
263  *  @hw: pointer to hardware structure
264  *
265  *  Starts the hardware by filling the bus info structure and media type, clears
266  *  all on chip counters, initializes receive address registers, multicast
267  *  table, VLAN filter table, calls routine to set up link and flow control
268  *  settings, and leaves transmit and receive units disabled and uninitialized
269  **/
270 int ixgbe_start_hw_generic(struct ixgbe_hw *hw)
271 {
272         u16 device_caps;
273         u32 ctrl_ext;
274         int ret_val;
275
276         /* Set the media type */
277         hw->phy.media_type = hw->mac.ops.get_media_type(hw);
278
279         /* Identify the PHY */
280         hw->phy.ops.identify(hw);
281
282         /* Clear the VLAN filter table */
283         hw->mac.ops.clear_vfta(hw);
284
285         /* Clear statistics registers */
286         hw->mac.ops.clear_hw_cntrs(hw);
287
288         /* Set No Snoop Disable */
289         ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT);
290         ctrl_ext |= IXGBE_CTRL_EXT_NS_DIS;
291         IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext);
292         IXGBE_WRITE_FLUSH(hw);
293
294         /* Setup flow control if method for doing so */
295         if (hw->mac.ops.setup_fc) {
296                 ret_val = hw->mac.ops.setup_fc(hw);
297                 if (ret_val)
298                         return ret_val;
299         }
300
301         /* Cashe bit indicating need for crosstalk fix */
302         switch (hw->mac.type) {
303         case ixgbe_mac_82599EB:
304         case ixgbe_mac_X550EM_x:
305         case ixgbe_mac_x550em_a:
306                 hw->mac.ops.get_device_caps(hw, &device_caps);
307                 if (device_caps & IXGBE_DEVICE_CAPS_NO_CROSSTALK_WR)
308                         hw->need_crosstalk_fix = false;
309                 else
310                         hw->need_crosstalk_fix = true;
311                 break;
312         default:
313                 hw->need_crosstalk_fix = false;
314                 break;
315         }
316
317         /* Clear adapter stopped flag */
318         hw->adapter_stopped = false;
319
320         return 0;
321 }
322
323 /**
324  *  ixgbe_start_hw_gen2 - Init sequence for common device family
325  *  @hw: pointer to hw structure
326  *
327  * Performs the init sequence common to the second generation
328  * of 10 GbE devices.
329  * Devices in the second generation:
330  *     82599
331  *     X540
332  **/
333 int ixgbe_start_hw_gen2(struct ixgbe_hw *hw)
334 {
335         u32 i;
336
337         /* Clear the rate limiters */
338         for (i = 0; i < hw->mac.max_tx_queues; i++) {
339                 IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, i);
340                 IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, 0);
341         }
342         IXGBE_WRITE_FLUSH(hw);
343
344         return 0;
345 }
346
347 /**
348  *  ixgbe_init_hw_generic - Generic hardware initialization
349  *  @hw: pointer to hardware structure
350  *
351  *  Initialize the hardware by resetting the hardware, filling the bus info
352  *  structure and media type, clears all on chip counters, initializes receive
353  *  address registers, multicast table, VLAN filter table, calls routine to set
354  *  up link and flow control settings, and leaves transmit and receive units
355  *  disabled and uninitialized
356  **/
357 int ixgbe_init_hw_generic(struct ixgbe_hw *hw)
358 {
359         int status;
360
361         /* Reset the hardware */
362         status = hw->mac.ops.reset_hw(hw);
363
364         if (status == 0) {
365                 /* Start the HW */
366                 status = hw->mac.ops.start_hw(hw);
367         }
368
369         /* Initialize the LED link active for LED blink support */
370         if (hw->mac.ops.init_led_link_act)
371                 hw->mac.ops.init_led_link_act(hw);
372
373         return status;
374 }
375
376 /**
377  *  ixgbe_clear_hw_cntrs_generic - Generic clear hardware counters
378  *  @hw: pointer to hardware structure
379  *
380  *  Clears all hardware statistics counters by reading them from the hardware
381  *  Statistics counters are clear on read.
382  **/
383 int ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw)
384 {
385         u16 i = 0;
386
387         IXGBE_READ_REG(hw, IXGBE_CRCERRS);
388         IXGBE_READ_REG(hw, IXGBE_ILLERRC);
389         IXGBE_READ_REG(hw, IXGBE_ERRBC);
390         IXGBE_READ_REG(hw, IXGBE_MSPDC);
391         for (i = 0; i < 8; i++)
392                 IXGBE_READ_REG(hw, IXGBE_MPC(i));
393
394         IXGBE_READ_REG(hw, IXGBE_MLFC);
395         IXGBE_READ_REG(hw, IXGBE_MRFC);
396         IXGBE_READ_REG(hw, IXGBE_RLEC);
397         IXGBE_READ_REG(hw, IXGBE_LXONTXC);
398         IXGBE_READ_REG(hw, IXGBE_LXOFFTXC);
399         if (hw->mac.type >= ixgbe_mac_82599EB) {
400                 IXGBE_READ_REG(hw, IXGBE_LXONRXCNT);
401                 IXGBE_READ_REG(hw, IXGBE_LXOFFRXCNT);
402         } else {
403                 IXGBE_READ_REG(hw, IXGBE_LXONRXC);
404                 IXGBE_READ_REG(hw, IXGBE_LXOFFRXC);
405         }
406
407         for (i = 0; i < 8; i++) {
408                 IXGBE_READ_REG(hw, IXGBE_PXONTXC(i));
409                 IXGBE_READ_REG(hw, IXGBE_PXOFFTXC(i));
410                 if (hw->mac.type >= ixgbe_mac_82599EB) {
411                         IXGBE_READ_REG(hw, IXGBE_PXONRXCNT(i));
412                         IXGBE_READ_REG(hw, IXGBE_PXOFFRXCNT(i));
413                 } else {
414                         IXGBE_READ_REG(hw, IXGBE_PXONRXC(i));
415                         IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i));
416                 }
417         }
418         if (hw->mac.type >= ixgbe_mac_82599EB)
419                 for (i = 0; i < 8; i++)
420                         IXGBE_READ_REG(hw, IXGBE_PXON2OFFCNT(i));
421         IXGBE_READ_REG(hw, IXGBE_PRC64);
422         IXGBE_READ_REG(hw, IXGBE_PRC127);
423         IXGBE_READ_REG(hw, IXGBE_PRC255);
424         IXGBE_READ_REG(hw, IXGBE_PRC511);
425         IXGBE_READ_REG(hw, IXGBE_PRC1023);
426         IXGBE_READ_REG(hw, IXGBE_PRC1522);
427         IXGBE_READ_REG(hw, IXGBE_GPRC);
428         IXGBE_READ_REG(hw, IXGBE_BPRC);
429         IXGBE_READ_REG(hw, IXGBE_MPRC);
430         IXGBE_READ_REG(hw, IXGBE_GPTC);
431         IXGBE_READ_REG(hw, IXGBE_GORCL);
432         IXGBE_READ_REG(hw, IXGBE_GORCH);
433         IXGBE_READ_REG(hw, IXGBE_GOTCL);
434         IXGBE_READ_REG(hw, IXGBE_GOTCH);
435         if (hw->mac.type == ixgbe_mac_82598EB)
436                 for (i = 0; i < 8; i++)
437                         IXGBE_READ_REG(hw, IXGBE_RNBC(i));
438         IXGBE_READ_REG(hw, IXGBE_RUC);
439         IXGBE_READ_REG(hw, IXGBE_RFC);
440         IXGBE_READ_REG(hw, IXGBE_ROC);
441         IXGBE_READ_REG(hw, IXGBE_RJC);
442         IXGBE_READ_REG(hw, IXGBE_MNGPRC);
443         IXGBE_READ_REG(hw, IXGBE_MNGPDC);
444         IXGBE_READ_REG(hw, IXGBE_MNGPTC);
445         IXGBE_READ_REG(hw, IXGBE_TORL);
446         IXGBE_READ_REG(hw, IXGBE_TORH);
447         IXGBE_READ_REG(hw, IXGBE_TPR);
448         IXGBE_READ_REG(hw, IXGBE_TPT);
449         IXGBE_READ_REG(hw, IXGBE_PTC64);
450         IXGBE_READ_REG(hw, IXGBE_PTC127);
451         IXGBE_READ_REG(hw, IXGBE_PTC255);
452         IXGBE_READ_REG(hw, IXGBE_PTC511);
453         IXGBE_READ_REG(hw, IXGBE_PTC1023);
454         IXGBE_READ_REG(hw, IXGBE_PTC1522);
455         IXGBE_READ_REG(hw, IXGBE_MPTC);
456         IXGBE_READ_REG(hw, IXGBE_BPTC);
457         for (i = 0; i < 16; i++) {
458                 IXGBE_READ_REG(hw, IXGBE_QPRC(i));
459                 IXGBE_READ_REG(hw, IXGBE_QPTC(i));
460                 if (hw->mac.type >= ixgbe_mac_82599EB) {
461                         IXGBE_READ_REG(hw, IXGBE_QBRC_L(i));
462                         IXGBE_READ_REG(hw, IXGBE_QBRC_H(i));
463                         IXGBE_READ_REG(hw, IXGBE_QBTC_L(i));
464                         IXGBE_READ_REG(hw, IXGBE_QBTC_H(i));
465                         IXGBE_READ_REG(hw, IXGBE_QPRDC(i));
466                 } else {
467                         IXGBE_READ_REG(hw, IXGBE_QBRC(i));
468                         IXGBE_READ_REG(hw, IXGBE_QBTC(i));
469                 }
470         }
471
472         if (hw->mac.type == ixgbe_mac_X550 || hw->mac.type == ixgbe_mac_X540) {
473                 if (hw->phy.id == 0)
474                         hw->phy.ops.identify(hw);
475                 hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECL, MDIO_MMD_PCS, &i);
476                 hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECH, MDIO_MMD_PCS, &i);
477                 hw->phy.ops.read_reg(hw, IXGBE_LDPCECL, MDIO_MMD_PCS, &i);
478                 hw->phy.ops.read_reg(hw, IXGBE_LDPCECH, MDIO_MMD_PCS, &i);
479         }
480
481         return 0;
482 }
483
484 /**
485  *  ixgbe_read_pba_string_generic - Reads part number string from EEPROM
486  *  @hw: pointer to hardware structure
487  *  @pba_num: stores the part number string from the EEPROM
488  *  @pba_num_size: part number string buffer length
489  *
490  *  Reads the part number string from the EEPROM.
491  **/
492 int ixgbe_read_pba_string_generic(struct ixgbe_hw *hw, u8 *pba_num,
493                                   u32 pba_num_size)
494 {
495         int ret_val;
496         u16 pba_ptr;
497         u16 offset;
498         u16 length;
499         u16 data;
500
501         if (pba_num == NULL) {
502                 hw_dbg(hw, "PBA string buffer was null\n");
503                 return -EINVAL;
504         }
505
506         ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data);
507         if (ret_val) {
508                 hw_dbg(hw, "NVM Read Error\n");
509                 return ret_val;
510         }
511
512         ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &pba_ptr);
513         if (ret_val) {
514                 hw_dbg(hw, "NVM Read Error\n");
515                 return ret_val;
516         }
517
518         /*
519          * if data is not ptr guard the PBA must be in legacy format which
520          * means pba_ptr is actually our second data word for the PBA number
521          * and we can decode it into an ascii string
522          */
523         if (data != IXGBE_PBANUM_PTR_GUARD) {
524                 hw_dbg(hw, "NVM PBA number is not stored as string\n");
525
526                 /* we will need 11 characters to store the PBA */
527                 if (pba_num_size < 11) {
528                         hw_dbg(hw, "PBA string buffer too small\n");
529                         return -ENOSPC;
530                 }
531
532                 /* extract hex string from data and pba_ptr */
533                 pba_num[0] = (data >> 12) & 0xF;
534                 pba_num[1] = (data >> 8) & 0xF;
535                 pba_num[2] = (data >> 4) & 0xF;
536                 pba_num[3] = data & 0xF;
537                 pba_num[4] = (pba_ptr >> 12) & 0xF;
538                 pba_num[5] = (pba_ptr >> 8) & 0xF;
539                 pba_num[6] = '-';
540                 pba_num[7] = 0;
541                 pba_num[8] = (pba_ptr >> 4) & 0xF;
542                 pba_num[9] = pba_ptr & 0xF;
543
544                 /* put a null character on the end of our string */
545                 pba_num[10] = '\0';
546
547                 /* switch all the data but the '-' to hex char */
548                 for (offset = 0; offset < 10; offset++) {
549                         if (pba_num[offset] < 0xA)
550                                 pba_num[offset] += '0';
551                         else if (pba_num[offset] < 0x10)
552                                 pba_num[offset] += 'A' - 0xA;
553                 }
554
555                 return 0;
556         }
557
558         ret_val = hw->eeprom.ops.read(hw, pba_ptr, &length);
559         if (ret_val) {
560                 hw_dbg(hw, "NVM Read Error\n");
561                 return ret_val;
562         }
563
564         if (length == 0xFFFF || length == 0) {
565                 hw_dbg(hw, "NVM PBA number section invalid length\n");
566                 return -EIO;
567         }
568
569         /* check if pba_num buffer is big enough */
570         if (pba_num_size  < (((u32)length * 2) - 1)) {
571                 hw_dbg(hw, "PBA string buffer too small\n");
572                 return -ENOSPC;
573         }
574
575         /* trim pba length from start of string */
576         pba_ptr++;
577         length--;
578
579         for (offset = 0; offset < length; offset++) {
580                 ret_val = hw->eeprom.ops.read(hw, pba_ptr + offset, &data);
581                 if (ret_val) {
582                         hw_dbg(hw, "NVM Read Error\n");
583                         return ret_val;
584                 }
585                 pba_num[offset * 2] = (u8)(data >> 8);
586                 pba_num[(offset * 2) + 1] = (u8)(data & 0xFF);
587         }
588         pba_num[offset * 2] = '\0';
589
590         return 0;
591 }
592
593 /**
594  *  ixgbe_get_mac_addr_generic - Generic get MAC address
595  *  @hw: pointer to hardware structure
596  *  @mac_addr: Adapter MAC address
597  *
598  *  Reads the adapter's MAC address from first Receive Address Register (RAR0)
599  *  A reset of the adapter must be performed prior to calling this function
600  *  in order for the MAC address to have been loaded from the EEPROM into RAR0
601  **/
602 int ixgbe_get_mac_addr_generic(struct ixgbe_hw *hw, u8 *mac_addr)
603 {
604         u32 rar_high;
605         u32 rar_low;
606         u16 i;
607
608         rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(0));
609         rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(0));
610
611         for (i = 0; i < 4; i++)
612                 mac_addr[i] = (u8)(rar_low >> (i*8));
613
614         for (i = 0; i < 2; i++)
615                 mac_addr[i+4] = (u8)(rar_high >> (i*8));
616
617         return 0;
618 }
619
620 enum ixgbe_bus_width ixgbe_convert_bus_width(u16 link_status)
621 {
622         switch (link_status & IXGBE_PCI_LINK_WIDTH) {
623         case IXGBE_PCI_LINK_WIDTH_1:
624                 return ixgbe_bus_width_pcie_x1;
625         case IXGBE_PCI_LINK_WIDTH_2:
626                 return ixgbe_bus_width_pcie_x2;
627         case IXGBE_PCI_LINK_WIDTH_4:
628                 return ixgbe_bus_width_pcie_x4;
629         case IXGBE_PCI_LINK_WIDTH_8:
630                 return ixgbe_bus_width_pcie_x8;
631         default:
632                 return ixgbe_bus_width_unknown;
633         }
634 }
635
636 enum ixgbe_bus_speed ixgbe_convert_bus_speed(u16 link_status)
637 {
638         switch (link_status & IXGBE_PCI_LINK_SPEED) {
639         case IXGBE_PCI_LINK_SPEED_2500:
640                 return ixgbe_bus_speed_2500;
641         case IXGBE_PCI_LINK_SPEED_5000:
642                 return ixgbe_bus_speed_5000;
643         case IXGBE_PCI_LINK_SPEED_8000:
644                 return ixgbe_bus_speed_8000;
645         default:
646                 return ixgbe_bus_speed_unknown;
647         }
648 }
649
650 /**
651  *  ixgbe_get_bus_info_generic - Generic set PCI bus info
652  *  @hw: pointer to hardware structure
653  *
654  *  Sets the PCI bus info (speed, width, type) within the ixgbe_hw structure
655  **/
656 int ixgbe_get_bus_info_generic(struct ixgbe_hw *hw)
657 {
658         u16 link_status;
659
660         hw->bus.type = ixgbe_bus_type_pci_express;
661
662         /* Get the negotiated link width and speed from PCI config space */
663         link_status = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_LINK_STATUS);
664
665         hw->bus.width = ixgbe_convert_bus_width(link_status);
666         hw->bus.speed = ixgbe_convert_bus_speed(link_status);
667
668         hw->mac.ops.set_lan_id(hw);
669
670         return 0;
671 }
672
673 /**
674  *  ixgbe_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices
675  *  @hw: pointer to the HW structure
676  *
677  *  Determines the LAN function id by reading memory-mapped registers
678  *  and swaps the port value if requested.
679  **/
680 void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw)
681 {
682         struct ixgbe_bus_info *bus = &hw->bus;
683         u16 ee_ctrl_4;
684         u32 reg;
685
686         reg = IXGBE_READ_REG(hw, IXGBE_STATUS);
687         bus->func = FIELD_GET(IXGBE_STATUS_LAN_ID, reg);
688         bus->lan_id = bus->func;
689
690         /* check for a port swap */
691         reg = IXGBE_READ_REG(hw, IXGBE_FACTPS(hw));
692         if (reg & IXGBE_FACTPS_LFS)
693                 bus->func ^= 0x1;
694
695         /* Get MAC instance from EEPROM for configuring CS4227 */
696         if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP) {
697                 hw->eeprom.ops.read(hw, IXGBE_EEPROM_CTRL_4, &ee_ctrl_4);
698                 bus->instance_id = FIELD_GET(IXGBE_EE_CTRL_4_INST_ID,
699                                              ee_ctrl_4);
700         }
701 }
702
703 /**
704  *  ixgbe_stop_adapter_generic - Generic stop Tx/Rx units
705  *  @hw: pointer to hardware structure
706  *
707  *  Sets the adapter_stopped flag within ixgbe_hw struct. Clears interrupts,
708  *  disables transmit and receive units. The adapter_stopped flag is used by
709  *  the shared code and drivers to determine if the adapter is in a stopped
710  *  state and should not touch the hardware.
711  **/
712 int ixgbe_stop_adapter_generic(struct ixgbe_hw *hw)
713 {
714         u32 reg_val;
715         u16 i;
716
717         /*
718          * Set the adapter_stopped flag so other driver functions stop touching
719          * the hardware
720          */
721         hw->adapter_stopped = true;
722
723         /* Disable the receive unit */
724         hw->mac.ops.disable_rx(hw);
725
726         /* Clear interrupt mask to stop interrupts from being generated */
727         IXGBE_WRITE_REG(hw, IXGBE_EIMC, IXGBE_IRQ_CLEAR_MASK);
728
729         /* Clear any pending interrupts, flush previous writes */
730         IXGBE_READ_REG(hw, IXGBE_EICR);
731
732         /* Disable the transmit unit.  Each queue must be disabled. */
733         for (i = 0; i < hw->mac.max_tx_queues; i++)
734                 IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), IXGBE_TXDCTL_SWFLSH);
735
736         /* Disable the receive unit by stopping each queue */
737         for (i = 0; i < hw->mac.max_rx_queues; i++) {
738                 reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i));
739                 reg_val &= ~IXGBE_RXDCTL_ENABLE;
740                 reg_val |= IXGBE_RXDCTL_SWFLSH;
741                 IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val);
742         }
743
744         /* flush all queues disables */
745         IXGBE_WRITE_FLUSH(hw);
746         usleep_range(1000, 2000);
747
748         /*
749          * Prevent the PCI-E bus from hanging by disabling PCI-E primary
750          * access and verify no pending requests
751          */
752         return ixgbe_disable_pcie_primary(hw);
753 }
754
755 /**
756  *  ixgbe_init_led_link_act_generic - Store the LED index link/activity.
757  *  @hw: pointer to hardware structure
758  *
759  *  Store the index for the link active LED. This will be used to support
760  *  blinking the LED.
761  **/
762 int ixgbe_init_led_link_act_generic(struct ixgbe_hw *hw)
763 {
764         struct ixgbe_mac_info *mac = &hw->mac;
765         u32 led_reg, led_mode;
766         u16 i;
767
768         led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
769
770         /* Get LED link active from the LEDCTL register */
771         for (i = 0; i < 4; i++) {
772                 led_mode = led_reg >> IXGBE_LED_MODE_SHIFT(i);
773
774                 if ((led_mode & IXGBE_LED_MODE_MASK_BASE) ==
775                     IXGBE_LED_LINK_ACTIVE) {
776                         mac->led_link_act = i;
777                         return 0;
778                 }
779         }
780
781         /* If LEDCTL register does not have the LED link active set, then use
782          * known MAC defaults.
783          */
784         switch (hw->mac.type) {
785         case ixgbe_mac_x550em_a:
786                 mac->led_link_act = 0;
787                 break;
788         case ixgbe_mac_X550EM_x:
789                 mac->led_link_act = 1;
790                 break;
791         default:
792                 mac->led_link_act = 2;
793         }
794
795         return 0;
796 }
797
798 /**
799  *  ixgbe_led_on_generic - Turns on the software controllable LEDs.
800  *  @hw: pointer to hardware structure
801  *  @index: led number to turn on
802  **/
803 int ixgbe_led_on_generic(struct ixgbe_hw *hw, u32 index)
804 {
805         u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
806
807         if (index > 3)
808                 return -EINVAL;
809
810         /* To turn on the LED, set mode to ON. */
811         led_reg &= ~IXGBE_LED_MODE_MASK(index);
812         led_reg |= IXGBE_LED_ON << IXGBE_LED_MODE_SHIFT(index);
813         IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
814         IXGBE_WRITE_FLUSH(hw);
815
816         return 0;
817 }
818
819 /**
820  *  ixgbe_led_off_generic - Turns off the software controllable LEDs.
821  *  @hw: pointer to hardware structure
822  *  @index: led number to turn off
823  **/
824 int ixgbe_led_off_generic(struct ixgbe_hw *hw, u32 index)
825 {
826         u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
827
828         if (index > 3)
829                 return -EINVAL;
830
831         /* To turn off the LED, set mode to OFF. */
832         led_reg &= ~IXGBE_LED_MODE_MASK(index);
833         led_reg |= IXGBE_LED_OFF << IXGBE_LED_MODE_SHIFT(index);
834         IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
835         IXGBE_WRITE_FLUSH(hw);
836
837         return 0;
838 }
839
840 /**
841  *  ixgbe_init_eeprom_params_generic - Initialize EEPROM params
842  *  @hw: pointer to hardware structure
843  *
844  *  Initializes the EEPROM parameters ixgbe_eeprom_info within the
845  *  ixgbe_hw struct in order to set up EEPROM access.
846  **/
847 int ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw)
848 {
849         struct ixgbe_eeprom_info *eeprom = &hw->eeprom;
850         u32 eec;
851         u16 eeprom_size;
852
853         if (eeprom->type == ixgbe_eeprom_uninitialized) {
854                 eeprom->type = ixgbe_eeprom_none;
855                 /* Set default semaphore delay to 10ms which is a well
856                  * tested value */
857                 eeprom->semaphore_delay = 10;
858                 /* Clear EEPROM page size, it will be initialized as needed */
859                 eeprom->word_page_size = 0;
860
861                 /*
862                  * Check for EEPROM present first.
863                  * If not present leave as none
864                  */
865                 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
866                 if (eec & IXGBE_EEC_PRES) {
867                         eeprom->type = ixgbe_eeprom_spi;
868
869                         /*
870                          * SPI EEPROM is assumed here.  This code would need to
871                          * change if a future EEPROM is not SPI.
872                          */
873                         eeprom_size = FIELD_GET(IXGBE_EEC_SIZE, eec);
874                         eeprom->word_size = BIT(eeprom_size +
875                                                 IXGBE_EEPROM_WORD_SIZE_SHIFT);
876                 }
877
878                 if (eec & IXGBE_EEC_ADDR_SIZE)
879                         eeprom->address_bits = 16;
880                 else
881                         eeprom->address_bits = 8;
882                 hw_dbg(hw, "Eeprom params: type = %d, size = %d, address bits: %d\n",
883                        eeprom->type, eeprom->word_size, eeprom->address_bits);
884         }
885
886         return 0;
887 }
888
889 /**
890  *  ixgbe_write_eeprom_buffer_bit_bang_generic - Write EEPROM using bit-bang
891  *  @hw: pointer to hardware structure
892  *  @offset: offset within the EEPROM to write
893  *  @words: number of words
894  *  @data: 16 bit word(s) to write to EEPROM
895  *
896  *  Reads 16 bit word(s) from EEPROM through bit-bang method
897  **/
898 int ixgbe_write_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
899                                                u16 words, u16 *data)
900 {
901         u16 i, count;
902         int status;
903
904         hw->eeprom.ops.init_params(hw);
905
906         if (words == 0 || (offset + words > hw->eeprom.word_size))
907                 return -EINVAL;
908
909         /*
910          * The EEPROM page size cannot be queried from the chip. We do lazy
911          * initialization. It is worth to do that when we write large buffer.
912          */
913         if ((hw->eeprom.word_page_size == 0) &&
914             (words > IXGBE_EEPROM_PAGE_SIZE_MAX))
915                 ixgbe_detect_eeprom_page_size_generic(hw, offset);
916
917         /*
918          * We cannot hold synchronization semaphores for too long
919          * to avoid other entity starvation. However it is more efficient
920          * to read in bursts than synchronizing access for each word.
921          */
922         for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) {
923                 count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ?
924                          IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i);
925                 status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset + i,
926                                                             count, &data[i]);
927
928                 if (status != 0)
929                         break;
930         }
931
932         return status;
933 }
934
935 /**
936  *  ixgbe_write_eeprom_buffer_bit_bang - Writes 16 bit word(s) to EEPROM
937  *  @hw: pointer to hardware structure
938  *  @offset: offset within the EEPROM to be written to
939  *  @words: number of word(s)
940  *  @data: 16 bit word(s) to be written to the EEPROM
941  *
942  *  If ixgbe_eeprom_update_checksum is not called after this function, the
943  *  EEPROM will most likely contain an invalid checksum.
944  **/
945 static int ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
946                                               u16 words, u16 *data)
947 {
948         u8 write_opcode = IXGBE_EEPROM_WRITE_OPCODE_SPI;
949         u16 page_size;
950         int status;
951         u16 word;
952         u16 i;
953
954         /* Prepare the EEPROM for writing  */
955         status = ixgbe_acquire_eeprom(hw);
956         if (status)
957                 return status;
958
959         if (ixgbe_ready_eeprom(hw) != 0) {
960                 ixgbe_release_eeprom(hw);
961                 return -EIO;
962         }
963
964         for (i = 0; i < words; i++) {
965                 ixgbe_standby_eeprom(hw);
966
967                 /* Send the WRITE ENABLE command (8 bit opcode) */
968                 ixgbe_shift_out_eeprom_bits(hw,
969                                             IXGBE_EEPROM_WREN_OPCODE_SPI,
970                                             IXGBE_EEPROM_OPCODE_BITS);
971
972                 ixgbe_standby_eeprom(hw);
973
974                 /* Some SPI eeproms use the 8th address bit embedded
975                  * in the opcode
976                  */
977                 if ((hw->eeprom.address_bits == 8) &&
978                     ((offset + i) >= 128))
979                         write_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI;
980
981                 /* Send the Write command (8-bit opcode + addr) */
982                 ixgbe_shift_out_eeprom_bits(hw, write_opcode,
983                                             IXGBE_EEPROM_OPCODE_BITS);
984                 ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2),
985                                             hw->eeprom.address_bits);
986
987                 page_size = hw->eeprom.word_page_size;
988
989                 /* Send the data in burst via SPI */
990                 do {
991                         word = data[i];
992                         word = (word >> 8) | (word << 8);
993                         ixgbe_shift_out_eeprom_bits(hw, word, 16);
994
995                         if (page_size == 0)
996                                 break;
997
998                         /* do not wrap around page */
999                         if (((offset + i) & (page_size - 1)) ==
1000                             (page_size - 1))
1001                                 break;
1002                 } while (++i < words);
1003
1004                 ixgbe_standby_eeprom(hw);
1005                 usleep_range(10000, 20000);
1006         }
1007         /* Done with writing - release the EEPROM */
1008         ixgbe_release_eeprom(hw);
1009
1010         return 0;
1011 }
1012
1013 /**
1014  *  ixgbe_write_eeprom_generic - Writes 16 bit value to EEPROM
1015  *  @hw: pointer to hardware structure
1016  *  @offset: offset within the EEPROM to be written to
1017  *  @data: 16 bit word to be written to the EEPROM
1018  *
1019  *  If ixgbe_eeprom_update_checksum is not called after this function, the
1020  *  EEPROM will most likely contain an invalid checksum.
1021  **/
1022 int ixgbe_write_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 data)
1023 {
1024         hw->eeprom.ops.init_params(hw);
1025
1026         if (offset >= hw->eeprom.word_size)
1027                 return -EINVAL;
1028
1029         return ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1, &data);
1030 }
1031
1032 /**
1033  *  ixgbe_read_eeprom_buffer_bit_bang_generic - Read EEPROM using bit-bang
1034  *  @hw: pointer to hardware structure
1035  *  @offset: offset within the EEPROM to be read
1036  *  @words: number of word(s)
1037  *  @data: read 16 bit words(s) from EEPROM
1038  *
1039  *  Reads 16 bit word(s) from EEPROM through bit-bang method
1040  **/
1041 int ixgbe_read_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
1042                                               u16 words, u16 *data)
1043 {
1044         u16 i, count;
1045         int status;
1046
1047         hw->eeprom.ops.init_params(hw);
1048
1049         if (words == 0 || (offset + words > hw->eeprom.word_size))
1050                 return -EINVAL;
1051
1052         /*
1053          * We cannot hold synchronization semaphores for too long
1054          * to avoid other entity starvation. However it is more efficient
1055          * to read in bursts than synchronizing access for each word.
1056          */
1057         for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) {
1058                 count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ?
1059                          IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i);
1060
1061                 status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset + i,
1062                                                            count, &data[i]);
1063
1064                 if (status)
1065                         return status;
1066         }
1067
1068         return 0;
1069 }
1070
1071 /**
1072  *  ixgbe_read_eeprom_buffer_bit_bang - Read EEPROM using bit-bang
1073  *  @hw: pointer to hardware structure
1074  *  @offset: offset within the EEPROM to be read
1075  *  @words: number of word(s)
1076  *  @data: read 16 bit word(s) from EEPROM
1077  *
1078  *  Reads 16 bit word(s) from EEPROM through bit-bang method
1079  **/
1080 static int ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
1081                                              u16 words, u16 *data)
1082 {
1083         u8 read_opcode = IXGBE_EEPROM_READ_OPCODE_SPI;
1084         u16 word_in;
1085         int status;
1086         u16 i;
1087
1088         /* Prepare the EEPROM for reading  */
1089         status = ixgbe_acquire_eeprom(hw);
1090         if (status)
1091                 return status;
1092
1093         if (ixgbe_ready_eeprom(hw) != 0) {
1094                 ixgbe_release_eeprom(hw);
1095                 return -EIO;
1096         }
1097
1098         for (i = 0; i < words; i++) {
1099                 ixgbe_standby_eeprom(hw);
1100                 /* Some SPI eeproms use the 8th address bit embedded
1101                  * in the opcode
1102                  */
1103                 if ((hw->eeprom.address_bits == 8) &&
1104                     ((offset + i) >= 128))
1105                         read_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI;
1106
1107                 /* Send the READ command (opcode + addr) */
1108                 ixgbe_shift_out_eeprom_bits(hw, read_opcode,
1109                                             IXGBE_EEPROM_OPCODE_BITS);
1110                 ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2),
1111                                             hw->eeprom.address_bits);
1112
1113                 /* Read the data. */
1114                 word_in = ixgbe_shift_in_eeprom_bits(hw, 16);
1115                 data[i] = (word_in >> 8) | (word_in << 8);
1116         }
1117
1118         /* End this read operation */
1119         ixgbe_release_eeprom(hw);
1120
1121         return 0;
1122 }
1123
1124 /**
1125  *  ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang
1126  *  @hw: pointer to hardware structure
1127  *  @offset: offset within the EEPROM to be read
1128  *  @data: read 16 bit value from EEPROM
1129  *
1130  *  Reads 16 bit value from EEPROM through bit-bang method
1131  **/
1132 int ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
1133                                        u16 *data)
1134 {
1135         hw->eeprom.ops.init_params(hw);
1136
1137         if (offset >= hw->eeprom.word_size)
1138                 return -EINVAL;
1139
1140         return ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data);
1141 }
1142
1143 /**
1144  *  ixgbe_read_eerd_buffer_generic - Read EEPROM word(s) using EERD
1145  *  @hw: pointer to hardware structure
1146  *  @offset: offset of word in the EEPROM to read
1147  *  @words: number of word(s)
1148  *  @data: 16 bit word(s) from the EEPROM
1149  *
1150  *  Reads a 16 bit word(s) from the EEPROM using the EERD register.
1151  **/
1152 int ixgbe_read_eerd_buffer_generic(struct ixgbe_hw *hw, u16 offset,
1153                                    u16 words, u16 *data)
1154 {
1155         int status;
1156         u32 eerd;
1157         u32 i;
1158
1159         hw->eeprom.ops.init_params(hw);
1160
1161         if (words == 0 || offset >= hw->eeprom.word_size)
1162                 return -EINVAL;
1163
1164         for (i = 0; i < words; i++) {
1165                 eerd = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
1166                        IXGBE_EEPROM_RW_REG_START;
1167
1168                 IXGBE_WRITE_REG(hw, IXGBE_EERD, eerd);
1169                 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_READ);
1170
1171                 if (status == 0) {
1172                         data[i] = (IXGBE_READ_REG(hw, IXGBE_EERD) >>
1173                                    IXGBE_EEPROM_RW_REG_DATA);
1174                 } else {
1175                         hw_dbg(hw, "Eeprom read timed out\n");
1176                         return status;
1177                 }
1178         }
1179
1180         return 0;
1181 }
1182
1183 /**
1184  *  ixgbe_detect_eeprom_page_size_generic - Detect EEPROM page size
1185  *  @hw: pointer to hardware structure
1186  *  @offset: offset within the EEPROM to be used as a scratch pad
1187  *
1188  *  Discover EEPROM page size by writing marching data at given offset.
1189  *  This function is called only when we are writing a new large buffer
1190  *  at given offset so the data would be overwritten anyway.
1191  **/
1192 static int ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
1193                                                  u16 offset)
1194 {
1195         u16 data[IXGBE_EEPROM_PAGE_SIZE_MAX];
1196         int status;
1197         u16 i;
1198
1199         for (i = 0; i < IXGBE_EEPROM_PAGE_SIZE_MAX; i++)
1200                 data[i] = i;
1201
1202         hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX;
1203         status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset,
1204                                              IXGBE_EEPROM_PAGE_SIZE_MAX, data);
1205         hw->eeprom.word_page_size = 0;
1206         if (status)
1207                 return status;
1208
1209         status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data);
1210         if (status)
1211                 return status;
1212
1213         /*
1214          * When writing in burst more than the actual page size
1215          * EEPROM address wraps around current page.
1216          */
1217         hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX - data[0];
1218
1219         hw_dbg(hw, "Detected EEPROM page size = %d words.\n",
1220                hw->eeprom.word_page_size);
1221         return 0;
1222 }
1223
1224 /**
1225  *  ixgbe_read_eerd_generic - Read EEPROM word using EERD
1226  *  @hw: pointer to hardware structure
1227  *  @offset: offset of  word in the EEPROM to read
1228  *  @data: word read from the EEPROM
1229  *
1230  *  Reads a 16 bit word from the EEPROM using the EERD register.
1231  **/
1232 int ixgbe_read_eerd_generic(struct ixgbe_hw *hw, u16 offset, u16 *data)
1233 {
1234         return ixgbe_read_eerd_buffer_generic(hw, offset, 1, data);
1235 }
1236
1237 /**
1238  *  ixgbe_write_eewr_buffer_generic - Write EEPROM word(s) using EEWR
1239  *  @hw: pointer to hardware structure
1240  *  @offset: offset of  word in the EEPROM to write
1241  *  @words: number of words
1242  *  @data: word(s) write to the EEPROM
1243  *
1244  *  Write a 16 bit word(s) to the EEPROM using the EEWR register.
1245  **/
1246 int ixgbe_write_eewr_buffer_generic(struct ixgbe_hw *hw, u16 offset,
1247                                     u16 words, u16 *data)
1248 {
1249         int status;
1250         u32 eewr;
1251         u16 i;
1252
1253         hw->eeprom.ops.init_params(hw);
1254
1255         if (words == 0 || offset >= hw->eeprom.word_size)
1256                 return -EINVAL;
1257
1258         for (i = 0; i < words; i++) {
1259                 eewr = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
1260                        (data[i] << IXGBE_EEPROM_RW_REG_DATA) |
1261                        IXGBE_EEPROM_RW_REG_START;
1262
1263                 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE);
1264                 if (status) {
1265                         hw_dbg(hw, "Eeprom write EEWR timed out\n");
1266                         return status;
1267                 }
1268
1269                 IXGBE_WRITE_REG(hw, IXGBE_EEWR, eewr);
1270
1271                 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE);
1272                 if (status) {
1273                         hw_dbg(hw, "Eeprom write EEWR timed out\n");
1274                         return status;
1275                 }
1276         }
1277
1278         return 0;
1279 }
1280
1281 /**
1282  *  ixgbe_write_eewr_generic - Write EEPROM word using EEWR
1283  *  @hw: pointer to hardware structure
1284  *  @offset: offset of  word in the EEPROM to write
1285  *  @data: word write to the EEPROM
1286  *
1287  *  Write a 16 bit word to the EEPROM using the EEWR register.
1288  **/
1289 int ixgbe_write_eewr_generic(struct ixgbe_hw *hw, u16 offset, u16 data)
1290 {
1291         return ixgbe_write_eewr_buffer_generic(hw, offset, 1, &data);
1292 }
1293
1294 /**
1295  *  ixgbe_poll_eerd_eewr_done - Poll EERD read or EEWR write status
1296  *  @hw: pointer to hardware structure
1297  *  @ee_reg: EEPROM flag for polling
1298  *
1299  *  Polls the status bit (bit 1) of the EERD or EEWR to determine when the
1300  *  read or write is done respectively.
1301  **/
1302 static int ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg)
1303 {
1304         u32 i;
1305         u32 reg;
1306
1307         for (i = 0; i < IXGBE_EERD_EEWR_ATTEMPTS; i++) {
1308                 if (ee_reg == IXGBE_NVM_POLL_READ)
1309                         reg = IXGBE_READ_REG(hw, IXGBE_EERD);
1310                 else
1311                         reg = IXGBE_READ_REG(hw, IXGBE_EEWR);
1312
1313                 if (reg & IXGBE_EEPROM_RW_REG_DONE) {
1314                         return 0;
1315                 }
1316                 udelay(5);
1317         }
1318         return -EIO;
1319 }
1320
1321 /**
1322  *  ixgbe_acquire_eeprom - Acquire EEPROM using bit-bang
1323  *  @hw: pointer to hardware structure
1324  *
1325  *  Prepares EEPROM for access using bit-bang method. This function should
1326  *  be called before issuing a command to the EEPROM.
1327  **/
1328 static int ixgbe_acquire_eeprom(struct ixgbe_hw *hw)
1329 {
1330         u32 eec;
1331         u32 i;
1332
1333         if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0)
1334                 return -EBUSY;
1335
1336         eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1337
1338         /* Request EEPROM Access */
1339         eec |= IXGBE_EEC_REQ;
1340         IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1341
1342         for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) {
1343                 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1344                 if (eec & IXGBE_EEC_GNT)
1345                         break;
1346                 udelay(5);
1347         }
1348
1349         /* Release if grant not acquired */
1350         if (!(eec & IXGBE_EEC_GNT)) {
1351                 eec &= ~IXGBE_EEC_REQ;
1352                 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1353                 hw_dbg(hw, "Could not acquire EEPROM grant\n");
1354
1355                 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
1356                 return -EIO;
1357         }
1358
1359         /* Setup EEPROM for Read/Write */
1360         /* Clear CS and SK */
1361         eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK);
1362         IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1363         IXGBE_WRITE_FLUSH(hw);
1364         udelay(1);
1365         return 0;
1366 }
1367
1368 /**
1369  *  ixgbe_get_eeprom_semaphore - Get hardware semaphore
1370  *  @hw: pointer to hardware structure
1371  *
1372  *  Sets the hardware semaphores so EEPROM access can occur for bit-bang method
1373  **/
1374 static int ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw)
1375 {
1376         u32 timeout = 2000;
1377         u32 i;
1378         u32 swsm;
1379
1380         /* Get SMBI software semaphore between device drivers first */
1381         for (i = 0; i < timeout; i++) {
1382                 /*
1383                  * If the SMBI bit is 0 when we read it, then the bit will be
1384                  * set and we have the semaphore
1385                  */
1386                 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1387                 if (!(swsm & IXGBE_SWSM_SMBI))
1388                         break;
1389                 usleep_range(50, 100);
1390         }
1391
1392         if (i == timeout) {
1393                 hw_dbg(hw, "Driver can't access the Eeprom - SMBI Semaphore not granted.\n");
1394                 /* this release is particularly important because our attempts
1395                  * above to get the semaphore may have succeeded, and if there
1396                  * was a timeout, we should unconditionally clear the semaphore
1397                  * bits to free the driver to make progress
1398                  */
1399                 ixgbe_release_eeprom_semaphore(hw);
1400
1401                 usleep_range(50, 100);
1402                 /* one last try
1403                  * If the SMBI bit is 0 when we read it, then the bit will be
1404                  * set and we have the semaphore
1405                  */
1406                 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1407                 if (swsm & IXGBE_SWSM_SMBI) {
1408                         hw_dbg(hw, "Software semaphore SMBI between device drivers not granted.\n");
1409                         return -EIO;
1410                 }
1411         }
1412
1413         /* Now get the semaphore between SW/FW through the SWESMBI bit */
1414         for (i = 0; i < timeout; i++) {
1415                 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1416
1417                 /* Set the SW EEPROM semaphore bit to request access */
1418                 swsm |= IXGBE_SWSM_SWESMBI;
1419                 IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);
1420
1421                 /* If we set the bit successfully then we got the
1422                  * semaphore.
1423                  */
1424                 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1425                 if (swsm & IXGBE_SWSM_SWESMBI)
1426                         break;
1427
1428                 usleep_range(50, 100);
1429         }
1430
1431         /* Release semaphores and return error if SW EEPROM semaphore
1432          * was not granted because we don't have access to the EEPROM
1433          */
1434         if (i >= timeout) {
1435                 hw_dbg(hw, "SWESMBI Software EEPROM semaphore not granted.\n");
1436                 ixgbe_release_eeprom_semaphore(hw);
1437                 return -EIO;
1438         }
1439
1440         return 0;
1441 }
1442
1443 /**
1444  *  ixgbe_release_eeprom_semaphore - Release hardware semaphore
1445  *  @hw: pointer to hardware structure
1446  *
1447  *  This function clears hardware semaphore bits.
1448  **/
1449 static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw)
1450 {
1451         u32 swsm;
1452
1453         swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1454
1455         /* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */
1456         swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI);
1457         IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);
1458         IXGBE_WRITE_FLUSH(hw);
1459 }
1460
1461 /**
1462  *  ixgbe_ready_eeprom - Polls for EEPROM ready
1463  *  @hw: pointer to hardware structure
1464  **/
1465 static int ixgbe_ready_eeprom(struct ixgbe_hw *hw)
1466 {
1467         u16 i;
1468         u8 spi_stat_reg;
1469
1470         /*
1471          * Read "Status Register" repeatedly until the LSB is cleared.  The
1472          * EEPROM will signal that the command has been completed by clearing
1473          * bit 0 of the internal status register.  If it's not cleared within
1474          * 5 milliseconds, then error out.
1475          */
1476         for (i = 0; i < IXGBE_EEPROM_MAX_RETRY_SPI; i += 5) {
1477                 ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_RDSR_OPCODE_SPI,
1478                                             IXGBE_EEPROM_OPCODE_BITS);
1479                 spi_stat_reg = (u8)ixgbe_shift_in_eeprom_bits(hw, 8);
1480                 if (!(spi_stat_reg & IXGBE_EEPROM_STATUS_RDY_SPI))
1481                         break;
1482
1483                 udelay(5);
1484                 ixgbe_standby_eeprom(hw);
1485         }
1486
1487         /*
1488          * On some parts, SPI write time could vary from 0-20mSec on 3.3V
1489          * devices (and only 0-5mSec on 5V devices)
1490          */
1491         if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) {
1492                 hw_dbg(hw, "SPI EEPROM Status error\n");
1493                 return -EIO;
1494         }
1495
1496         return 0;
1497 }
1498
1499 /**
1500  *  ixgbe_standby_eeprom - Returns EEPROM to a "standby" state
1501  *  @hw: pointer to hardware structure
1502  **/
1503 static void ixgbe_standby_eeprom(struct ixgbe_hw *hw)
1504 {
1505         u32 eec;
1506
1507         eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1508
1509         /* Toggle CS to flush commands */
1510         eec |= IXGBE_EEC_CS;
1511         IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1512         IXGBE_WRITE_FLUSH(hw);
1513         udelay(1);
1514         eec &= ~IXGBE_EEC_CS;
1515         IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1516         IXGBE_WRITE_FLUSH(hw);
1517         udelay(1);
1518 }
1519
1520 /**
1521  *  ixgbe_shift_out_eeprom_bits - Shift data bits out to the EEPROM.
1522  *  @hw: pointer to hardware structure
1523  *  @data: data to send to the EEPROM
1524  *  @count: number of bits to shift out
1525  **/
1526 static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
1527                                         u16 count)
1528 {
1529         u32 eec;
1530         u32 mask;
1531         u32 i;
1532
1533         eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1534
1535         /*
1536          * Mask is used to shift "count" bits of "data" out to the EEPROM
1537          * one bit at a time.  Determine the starting bit based on count
1538          */
1539         mask = BIT(count - 1);
1540
1541         for (i = 0; i < count; i++) {
1542                 /*
1543                  * A "1" is shifted out to the EEPROM by setting bit "DI" to a
1544                  * "1", and then raising and then lowering the clock (the SK
1545                  * bit controls the clock input to the EEPROM).  A "0" is
1546                  * shifted out to the EEPROM by setting "DI" to "0" and then
1547                  * raising and then lowering the clock.
1548                  */
1549                 if (data & mask)
1550                         eec |= IXGBE_EEC_DI;
1551                 else
1552                         eec &= ~IXGBE_EEC_DI;
1553
1554                 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1555                 IXGBE_WRITE_FLUSH(hw);
1556
1557                 udelay(1);
1558
1559                 ixgbe_raise_eeprom_clk(hw, &eec);
1560                 ixgbe_lower_eeprom_clk(hw, &eec);
1561
1562                 /*
1563                  * Shift mask to signify next bit of data to shift in to the
1564                  * EEPROM
1565                  */
1566                 mask = mask >> 1;
1567         }
1568
1569         /* We leave the "DI" bit set to "0" when we leave this routine. */
1570         eec &= ~IXGBE_EEC_DI;
1571         IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1572         IXGBE_WRITE_FLUSH(hw);
1573 }
1574
1575 /**
1576  *  ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM
1577  *  @hw: pointer to hardware structure
1578  *  @count: number of bits to shift
1579  **/
1580 static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count)
1581 {
1582         u32 eec;
1583         u32 i;
1584         u16 data = 0;
1585
1586         /*
1587          * In order to read a register from the EEPROM, we need to shift
1588          * 'count' bits in from the EEPROM. Bits are "shifted in" by raising
1589          * the clock input to the EEPROM (setting the SK bit), and then reading
1590          * the value of the "DO" bit.  During this "shifting in" process the
1591          * "DI" bit should always be clear.
1592          */
1593         eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1594
1595         eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI);
1596
1597         for (i = 0; i < count; i++) {
1598                 data = data << 1;
1599                 ixgbe_raise_eeprom_clk(hw, &eec);
1600
1601                 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1602
1603                 eec &= ~(IXGBE_EEC_DI);
1604                 if (eec & IXGBE_EEC_DO)
1605                         data |= 1;
1606
1607                 ixgbe_lower_eeprom_clk(hw, &eec);
1608         }
1609
1610         return data;
1611 }
1612
1613 /**
1614  *  ixgbe_raise_eeprom_clk - Raises the EEPROM's clock input.
1615  *  @hw: pointer to hardware structure
1616  *  @eec: EEC register's current value
1617  **/
1618 static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
1619 {
1620         /*
1621          * Raise the clock input to the EEPROM
1622          * (setting the SK bit), then delay
1623          */
1624         *eec = *eec | IXGBE_EEC_SK;
1625         IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
1626         IXGBE_WRITE_FLUSH(hw);
1627         udelay(1);
1628 }
1629
1630 /**
1631  *  ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input.
1632  *  @hw: pointer to hardware structure
1633  *  @eec: EEC's current value
1634  **/
1635 static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
1636 {
1637         /*
1638          * Lower the clock input to the EEPROM (clearing the SK bit), then
1639          * delay
1640          */
1641         *eec = *eec & ~IXGBE_EEC_SK;
1642         IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
1643         IXGBE_WRITE_FLUSH(hw);
1644         udelay(1);
1645 }
1646
1647 /**
1648  *  ixgbe_release_eeprom - Release EEPROM, release semaphores
1649  *  @hw: pointer to hardware structure
1650  **/
1651 static void ixgbe_release_eeprom(struct ixgbe_hw *hw)
1652 {
1653         u32 eec;
1654
1655         eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1656
1657         eec |= IXGBE_EEC_CS;  /* Pull CS high */
1658         eec &= ~IXGBE_EEC_SK; /* Lower SCK */
1659
1660         IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1661         IXGBE_WRITE_FLUSH(hw);
1662
1663         udelay(1);
1664
1665         /* Stop requesting EEPROM access */
1666         eec &= ~IXGBE_EEC_REQ;
1667         IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1668
1669         hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
1670
1671         /*
1672          * Delay before attempt to obtain semaphore again to allow FW
1673          * access. semaphore_delay is in ms we need us for usleep_range
1674          */
1675         usleep_range(hw->eeprom.semaphore_delay * 1000,
1676                      hw->eeprom.semaphore_delay * 2000);
1677 }
1678
1679 /**
1680  *  ixgbe_calc_eeprom_checksum_generic - Calculates and returns the checksum
1681  *  @hw: pointer to hardware structure
1682  **/
1683 int ixgbe_calc_eeprom_checksum_generic(struct ixgbe_hw *hw)
1684 {
1685         u16 i;
1686         u16 j;
1687         u16 checksum = 0;
1688         u16 length = 0;
1689         u16 pointer = 0;
1690         u16 word = 0;
1691
1692         /* Include 0x0-0x3F in the checksum */
1693         for (i = 0; i < IXGBE_EEPROM_CHECKSUM; i++) {
1694                 if (hw->eeprom.ops.read(hw, i, &word)) {
1695                         hw_dbg(hw, "EEPROM read failed\n");
1696                         break;
1697                 }
1698                 checksum += word;
1699         }
1700
1701         /* Include all data from pointers except for the fw pointer */
1702         for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) {
1703                 if (hw->eeprom.ops.read(hw, i, &pointer)) {
1704                         hw_dbg(hw, "EEPROM read failed\n");
1705                         return -EIO;
1706                 }
1707
1708                 /* If the pointer seems invalid */
1709                 if (pointer == 0xFFFF || pointer == 0)
1710                         continue;
1711
1712                 if (hw->eeprom.ops.read(hw, pointer, &length)) {
1713                         hw_dbg(hw, "EEPROM read failed\n");
1714                         return -EIO;
1715                 }
1716
1717                 if (length == 0xFFFF || length == 0)
1718                         continue;
1719
1720                 for (j = pointer + 1; j <= pointer + length; j++) {
1721                         if (hw->eeprom.ops.read(hw, j, &word)) {
1722                                 hw_dbg(hw, "EEPROM read failed\n");
1723                                 return -EIO;
1724                         }
1725                         checksum += word;
1726                 }
1727         }
1728
1729         checksum = (u16)IXGBE_EEPROM_SUM - checksum;
1730
1731         return (int)checksum;
1732 }
1733
1734 /**
1735  *  ixgbe_validate_eeprom_checksum_generic - Validate EEPROM checksum
1736  *  @hw: pointer to hardware structure
1737  *  @checksum_val: calculated checksum
1738  *
1739  *  Performs checksum calculation and validates the EEPROM checksum.  If the
1740  *  caller does not need checksum_val, the value can be NULL.
1741  **/
1742 int ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw *hw,
1743                                            u16 *checksum_val)
1744 {
1745         u16 read_checksum = 0;
1746         u16 checksum;
1747         int status;
1748
1749         /*
1750          * Read the first word from the EEPROM. If this times out or fails, do
1751          * not continue or we could be in for a very long wait while every
1752          * EEPROM read fails
1753          */
1754         status = hw->eeprom.ops.read(hw, 0, &checksum);
1755         if (status) {
1756                 hw_dbg(hw, "EEPROM read failed\n");
1757                 return status;
1758         }
1759
1760         status = hw->eeprom.ops.calc_checksum(hw);
1761         if (status < 0)
1762                 return status;
1763
1764         checksum = (u16)(status & 0xffff);
1765
1766         status = hw->eeprom.ops.read(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum);
1767         if (status) {
1768                 hw_dbg(hw, "EEPROM read failed\n");
1769                 return status;
1770         }
1771
1772         /* Verify read checksum from EEPROM is the same as
1773          * calculated checksum
1774          */
1775         if (read_checksum != checksum)
1776                 status = -EIO;
1777
1778         /* If the user cares, return the calculated checksum */
1779         if (checksum_val)
1780                 *checksum_val = checksum;
1781
1782         return status;
1783 }
1784
1785 /**
1786  *  ixgbe_update_eeprom_checksum_generic - Updates the EEPROM checksum
1787  *  @hw: pointer to hardware structure
1788  **/
1789 int ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw)
1790 {
1791         u16 checksum;
1792         int status;
1793
1794         /*
1795          * Read the first word from the EEPROM. If this times out or fails, do
1796          * not continue or we could be in for a very long wait while every
1797          * EEPROM read fails
1798          */
1799         status = hw->eeprom.ops.read(hw, 0, &checksum);
1800         if (status) {
1801                 hw_dbg(hw, "EEPROM read failed\n");
1802                 return status;
1803         }
1804
1805         status = hw->eeprom.ops.calc_checksum(hw);
1806         if (status < 0)
1807                 return status;
1808
1809         checksum = (u16)(status & 0xffff);
1810
1811         status = hw->eeprom.ops.write(hw, IXGBE_EEPROM_CHECKSUM, checksum);
1812
1813         return status;
1814 }
1815
1816 /**
1817  *  ixgbe_set_rar_generic - Set Rx address register
1818  *  @hw: pointer to hardware structure
1819  *  @index: Receive address register to write
1820  *  @addr: Address to put into receive address register
1821  *  @vmdq: VMDq "set" or "pool" index
1822  *  @enable_addr: set flag that address is active
1823  *
1824  *  Puts an ethernet address into a receive address register.
1825  **/
1826 int ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq,
1827                           u32 enable_addr)
1828 {
1829         u32 rar_low, rar_high;
1830         u32 rar_entries = hw->mac.num_rar_entries;
1831
1832         /* Make sure we are using a valid rar index range */
1833         if (index >= rar_entries) {
1834                 hw_dbg(hw, "RAR index %d is out of range.\n", index);
1835                 return -EINVAL;
1836         }
1837
1838         /* setup VMDq pool selection before this RAR gets enabled */
1839         hw->mac.ops.set_vmdq(hw, index, vmdq);
1840
1841         /*
1842          * HW expects these in little endian so we reverse the byte
1843          * order from network order (big endian) to little endian
1844          */
1845         rar_low = ((u32)addr[0] |
1846                    ((u32)addr[1] << 8) |
1847                    ((u32)addr[2] << 16) |
1848                    ((u32)addr[3] << 24));
1849         /*
1850          * Some parts put the VMDq setting in the extra RAH bits,
1851          * so save everything except the lower 16 bits that hold part
1852          * of the address and the address valid bit.
1853          */
1854         rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index));
1855         rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV);
1856         rar_high |= ((u32)addr[4] | ((u32)addr[5] << 8));
1857
1858         if (enable_addr != 0)
1859                 rar_high |= IXGBE_RAH_AV;
1860
1861         /* Record lower 32 bits of MAC address and then make
1862          * sure that write is flushed to hardware before writing
1863          * the upper 16 bits and setting the valid bit.
1864          */
1865         IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low);
1866         IXGBE_WRITE_FLUSH(hw);
1867         IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high);
1868
1869         return 0;
1870 }
1871
1872 /**
1873  *  ixgbe_clear_rar_generic - Remove Rx address register
1874  *  @hw: pointer to hardware structure
1875  *  @index: Receive address register to write
1876  *
1877  *  Clears an ethernet address from a receive address register.
1878  **/
1879 int ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index)
1880 {
1881         u32 rar_high;
1882         u32 rar_entries = hw->mac.num_rar_entries;
1883
1884         /* Make sure we are using a valid rar index range */
1885         if (index >= rar_entries) {
1886                 hw_dbg(hw, "RAR index %d is out of range.\n", index);
1887                 return -EINVAL;
1888         }
1889
1890         /*
1891          * Some parts put the VMDq setting in the extra RAH bits,
1892          * so save everything except the lower 16 bits that hold part
1893          * of the address and the address valid bit.
1894          */
1895         rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index));
1896         rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV);
1897
1898         /* Clear the address valid bit and upper 16 bits of the address
1899          * before clearing the lower bits. This way we aren't updating
1900          * a live filter.
1901          */
1902         IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high);
1903         IXGBE_WRITE_FLUSH(hw);
1904         IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0);
1905
1906         /* clear VMDq pool/queue selection for this RAR */
1907         hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL);
1908
1909         return 0;
1910 }
1911
1912 /**
1913  *  ixgbe_init_rx_addrs_generic - Initializes receive address filters.
1914  *  @hw: pointer to hardware structure
1915  *
1916  *  Places the MAC address in receive address register 0 and clears the rest
1917  *  of the receive address registers. Clears the multicast table. Assumes
1918  *  the receiver is in reset when the routine is called.
1919  **/
1920 int ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw)
1921 {
1922         u32 i;
1923         u32 rar_entries = hw->mac.num_rar_entries;
1924
1925         /*
1926          * If the current mac address is valid, assume it is a software override
1927          * to the permanent address.
1928          * Otherwise, use the permanent address from the eeprom.
1929          */
1930         if (!is_valid_ether_addr(hw->mac.addr)) {
1931                 /* Get the MAC address from the RAR0 for later reference */
1932                 hw->mac.ops.get_mac_addr(hw, hw->mac.addr);
1933
1934                 hw_dbg(hw, " Keeping Current RAR0 Addr =%pM\n", hw->mac.addr);
1935         } else {
1936                 /* Setup the receive address. */
1937                 hw_dbg(hw, "Overriding MAC Address in RAR[0]\n");
1938                 hw_dbg(hw, " New MAC Addr =%pM\n", hw->mac.addr);
1939
1940                 hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV);
1941         }
1942
1943         /*  clear VMDq pool/queue selection for RAR 0 */
1944         hw->mac.ops.clear_vmdq(hw, 0, IXGBE_CLEAR_VMDQ_ALL);
1945
1946         hw->addr_ctrl.overflow_promisc = 0;
1947
1948         hw->addr_ctrl.rar_used_count = 1;
1949
1950         /* Zero out the other receive addresses. */
1951         hw_dbg(hw, "Clearing RAR[1-%d]\n", rar_entries - 1);
1952         for (i = 1; i < rar_entries; i++) {
1953                 IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0);
1954                 IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0);
1955         }
1956
1957         /* Clear the MTA */
1958         hw->addr_ctrl.mta_in_use = 0;
1959         IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type);
1960
1961         hw_dbg(hw, " Clearing MTA\n");
1962         for (i = 0; i < hw->mac.mcft_size; i++)
1963                 IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0);
1964
1965         if (hw->mac.ops.init_uta_tables)
1966                 hw->mac.ops.init_uta_tables(hw);
1967
1968         return 0;
1969 }
1970
1971 /**
1972  *  ixgbe_mta_vector - Determines bit-vector in multicast table to set
1973  *  @hw: pointer to hardware structure
1974  *  @mc_addr: the multicast address
1975  *
1976  *  Extracts the 12 bits, from a multicast address, to determine which
1977  *  bit-vector to set in the multicast table. The hardware uses 12 bits, from
1978  *  incoming rx multicast addresses, to determine the bit-vector to check in
1979  *  the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set
1980  *  by the MO field of the MCSTCTRL. The MO field is set during initialization
1981  *  to mc_filter_type.
1982  **/
1983 static int ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr)
1984 {
1985         u32 vector = 0;
1986
1987         switch (hw->mac.mc_filter_type) {
1988         case 0:   /* use bits [47:36] of the address */
1989                 vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4));
1990                 break;
1991         case 1:   /* use bits [46:35] of the address */
1992                 vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5));
1993                 break;
1994         case 2:   /* use bits [45:34] of the address */
1995                 vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6));
1996                 break;
1997         case 3:   /* use bits [43:32] of the address */
1998                 vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8));
1999                 break;
2000         default:  /* Invalid mc_filter_type */
2001                 hw_dbg(hw, "MC filter type param set incorrectly\n");
2002                 break;
2003         }
2004
2005         /* vector can only be 12-bits or boundary will be exceeded */
2006         vector &= 0xFFF;
2007         return vector;
2008 }
2009
2010 /**
2011  *  ixgbe_set_mta - Set bit-vector in multicast table
2012  *  @hw: pointer to hardware structure
2013  *  @mc_addr: Multicast address
2014  *
2015  *  Sets the bit-vector in the multicast table.
2016  **/
2017 static void ixgbe_set_mta(struct ixgbe_hw *hw, u8 *mc_addr)
2018 {
2019         u32 vector;
2020         u32 vector_bit;
2021         u32 vector_reg;
2022
2023         hw->addr_ctrl.mta_in_use++;
2024
2025         vector = ixgbe_mta_vector(hw, mc_addr);
2026         hw_dbg(hw, " bit-vector = 0x%03X\n", vector);
2027
2028         /*
2029          * The MTA is a register array of 128 32-bit registers. It is treated
2030          * like an array of 4096 bits.  We want to set bit
2031          * BitArray[vector_value]. So we figure out what register the bit is
2032          * in, read it, OR in the new bit, then write back the new value.  The
2033          * register is determined by the upper 7 bits of the vector value and
2034          * the bit within that register are determined by the lower 5 bits of
2035          * the value.
2036          */
2037         vector_reg = (vector >> 5) & 0x7F;
2038         vector_bit = vector & 0x1F;
2039         hw->mac.mta_shadow[vector_reg] |= BIT(vector_bit);
2040 }
2041
2042 /**
2043  *  ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses
2044  *  @hw: pointer to hardware structure
2045  *  @netdev: pointer to net device structure
2046  *
2047  *  The given list replaces any existing list. Clears the MC addrs from receive
2048  *  address registers and the multicast table. Uses unused receive address
2049  *  registers for the first multicast addresses, and hashes the rest into the
2050  *  multicast table.
2051  **/
2052 int ixgbe_update_mc_addr_list_generic(struct ixgbe_hw *hw,
2053                                       struct net_device *netdev)
2054 {
2055         struct netdev_hw_addr *ha;
2056         u32 i;
2057
2058         /*
2059          * Set the new number of MC addresses that we are being requested to
2060          * use.
2061          */
2062         hw->addr_ctrl.num_mc_addrs = netdev_mc_count(netdev);
2063         hw->addr_ctrl.mta_in_use = 0;
2064
2065         /* Clear mta_shadow */
2066         hw_dbg(hw, " Clearing MTA\n");
2067         memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
2068
2069         /* Update mta shadow */
2070         netdev_for_each_mc_addr(ha, netdev) {
2071                 hw_dbg(hw, " Adding the multicast addresses:\n");
2072                 ixgbe_set_mta(hw, ha->addr);
2073         }
2074
2075         /* Enable mta */
2076         for (i = 0; i < hw->mac.mcft_size; i++)
2077                 IXGBE_WRITE_REG_ARRAY(hw, IXGBE_MTA(0), i,
2078                                       hw->mac.mta_shadow[i]);
2079
2080         if (hw->addr_ctrl.mta_in_use > 0)
2081                 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL,
2082                                 IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type);
2083
2084         hw_dbg(hw, "ixgbe_update_mc_addr_list_generic Complete\n");
2085         return 0;
2086 }
2087
2088 /**
2089  *  ixgbe_enable_mc_generic - Enable multicast address in RAR
2090  *  @hw: pointer to hardware structure
2091  *
2092  *  Enables multicast address in RAR and the use of the multicast hash table.
2093  **/
2094 int ixgbe_enable_mc_generic(struct ixgbe_hw *hw)
2095 {
2096         struct ixgbe_addr_filter_info *a = &hw->addr_ctrl;
2097
2098         if (a->mta_in_use > 0)
2099                 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, IXGBE_MCSTCTRL_MFE |
2100                                 hw->mac.mc_filter_type);
2101
2102         return 0;
2103 }
2104
2105 /**
2106  *  ixgbe_disable_mc_generic - Disable multicast address in RAR
2107  *  @hw: pointer to hardware structure
2108  *
2109  *  Disables multicast address in RAR and the use of the multicast hash table.
2110  **/
2111 int ixgbe_disable_mc_generic(struct ixgbe_hw *hw)
2112 {
2113         struct ixgbe_addr_filter_info *a = &hw->addr_ctrl;
2114
2115         if (a->mta_in_use > 0)
2116                 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type);
2117
2118         return 0;
2119 }
2120
2121 /**
2122  *  ixgbe_fc_enable_generic - Enable flow control
2123  *  @hw: pointer to hardware structure
2124  *
2125  *  Enable flow control according to the current settings.
2126  **/
2127 int ixgbe_fc_enable_generic(struct ixgbe_hw *hw)
2128 {
2129         u32 mflcn_reg, fccfg_reg;
2130         u32 reg;
2131         u32 fcrtl, fcrth;
2132         int i;
2133
2134         /* Validate the water mark configuration. */
2135         if (!hw->fc.pause_time)
2136                 return -EINVAL;
2137
2138         /* Low water mark of zero causes XOFF floods */
2139         for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
2140                 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) &&
2141                     hw->fc.high_water[i]) {
2142                         if (!hw->fc.low_water[i] ||
2143                             hw->fc.low_water[i] >= hw->fc.high_water[i]) {
2144                                 hw_dbg(hw, "Invalid water mark configuration\n");
2145                                 return -EINVAL;
2146                         }
2147                 }
2148         }
2149
2150         /* Negotiate the fc mode to use */
2151         hw->mac.ops.fc_autoneg(hw);
2152
2153         /* Disable any previous flow control settings */
2154         mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN);
2155         mflcn_reg &= ~(IXGBE_MFLCN_RPFCE_MASK | IXGBE_MFLCN_RFCE);
2156
2157         fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG);
2158         fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY);
2159
2160         /*
2161          * The possible values of fc.current_mode are:
2162          * 0: Flow control is completely disabled
2163          * 1: Rx flow control is enabled (we can receive pause frames,
2164          *    but not send pause frames).
2165          * 2: Tx flow control is enabled (we can send pause frames but
2166          *    we do not support receiving pause frames).
2167          * 3: Both Rx and Tx flow control (symmetric) are enabled.
2168          * other: Invalid.
2169          */
2170         switch (hw->fc.current_mode) {
2171         case ixgbe_fc_none:
2172                 /*
2173                  * Flow control is disabled by software override or autoneg.
2174                  * The code below will actually disable it in the HW.
2175                  */
2176                 break;
2177         case ixgbe_fc_rx_pause:
2178                 /*
2179                  * Rx Flow control is enabled and Tx Flow control is
2180                  * disabled by software override. Since there really
2181                  * isn't a way to advertise that we are capable of RX
2182                  * Pause ONLY, we will advertise that we support both
2183                  * symmetric and asymmetric Rx PAUSE.  Later, we will
2184                  * disable the adapter's ability to send PAUSE frames.
2185                  */
2186                 mflcn_reg |= IXGBE_MFLCN_RFCE;
2187                 break;
2188         case ixgbe_fc_tx_pause:
2189                 /*
2190                  * Tx Flow control is enabled, and Rx Flow control is
2191                  * disabled by software override.
2192                  */
2193                 fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
2194                 break;
2195         case ixgbe_fc_full:
2196                 /* Flow control (both Rx and Tx) is enabled by SW override. */
2197                 mflcn_reg |= IXGBE_MFLCN_RFCE;
2198                 fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
2199                 break;
2200         default:
2201                 hw_dbg(hw, "Flow control param set incorrectly\n");
2202                 return -EIO;
2203         }
2204
2205         /* Set 802.3x based flow control settings. */
2206         mflcn_reg |= IXGBE_MFLCN_DPF;
2207         IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg);
2208         IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg);
2209
2210         /* Set up and enable Rx high/low water mark thresholds, enable XON. */
2211         for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
2212                 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) &&
2213                     hw->fc.high_water[i]) {
2214                         fcrtl = (hw->fc.low_water[i] << 10) | IXGBE_FCRTL_XONE;
2215                         IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), fcrtl);
2216                         fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN;
2217                 } else {
2218                         IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), 0);
2219                         /*
2220                          * In order to prevent Tx hangs when the internal Tx
2221                          * switch is enabled we must set the high water mark
2222                          * to the Rx packet buffer size - 24KB.  This allows
2223                          * the Tx switch to function even under heavy Rx
2224                          * workloads.
2225                          */
2226                         fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576;
2227                 }
2228
2229                 IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth);
2230         }
2231
2232         /* Configure pause time (2 TCs per register) */
2233         reg = hw->fc.pause_time * 0x00010001U;
2234         for (i = 0; i < (MAX_TRAFFIC_CLASS / 2); i++)
2235                 IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg);
2236
2237         IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2);
2238
2239         return 0;
2240 }
2241
2242 /**
2243  *  ixgbe_negotiate_fc - Negotiate flow control
2244  *  @hw: pointer to hardware structure
2245  *  @adv_reg: flow control advertised settings
2246  *  @lp_reg: link partner's flow control settings
2247  *  @adv_sym: symmetric pause bit in advertisement
2248  *  @adv_asm: asymmetric pause bit in advertisement
2249  *  @lp_sym: symmetric pause bit in link partner advertisement
2250  *  @lp_asm: asymmetric pause bit in link partner advertisement
2251  *
2252  *  Find the intersection between advertised settings and link partner's
2253  *  advertised settings
2254  **/
2255 int ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
2256                        u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
2257 {
2258         if ((!(adv_reg)) ||  (!(lp_reg)))
2259                 return -EINVAL;
2260
2261         if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
2262                 /*
2263                  * Now we need to check if the user selected Rx ONLY
2264                  * of pause frames.  In this case, we had to advertise
2265                  * FULL flow control because we could not advertise RX
2266                  * ONLY. Hence, we must now check to see if we need to
2267                  * turn OFF the TRANSMISSION of PAUSE frames.
2268                  */
2269                 if (hw->fc.requested_mode == ixgbe_fc_full) {
2270                         hw->fc.current_mode = ixgbe_fc_full;
2271                         hw_dbg(hw, "Flow Control = FULL.\n");
2272                 } else {
2273                         hw->fc.current_mode = ixgbe_fc_rx_pause;
2274                         hw_dbg(hw, "Flow Control=RX PAUSE frames only\n");
2275                 }
2276         } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) &&
2277                    (lp_reg & lp_sym) && (lp_reg & lp_asm)) {
2278                 hw->fc.current_mode = ixgbe_fc_tx_pause;
2279                 hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
2280         } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) &&
2281                    !(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
2282                 hw->fc.current_mode = ixgbe_fc_rx_pause;
2283                 hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
2284         } else {
2285                 hw->fc.current_mode = ixgbe_fc_none;
2286                 hw_dbg(hw, "Flow Control = NONE.\n");
2287         }
2288         return 0;
2289 }
2290
2291 /**
2292  *  ixgbe_fc_autoneg_fiber - Enable flow control on 1 gig fiber
2293  *  @hw: pointer to hardware structure
2294  *
2295  *  Enable flow control according on 1 gig fiber.
2296  **/
2297 static int ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw)
2298 {
2299         u32 pcs_anadv_reg, pcs_lpab_reg, linkstat;
2300         int ret_val;
2301
2302         /*
2303          * On multispeed fiber at 1g, bail out if
2304          * - link is up but AN did not complete, or if
2305          * - link is up and AN completed but timed out
2306          */
2307
2308         linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
2309         if ((!!(linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
2310             (!!(linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1))
2311                 return -EIO;
2312
2313         pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
2314         pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
2315
2316         ret_val =  ixgbe_negotiate_fc(hw, pcs_anadv_reg,
2317                                pcs_lpab_reg, IXGBE_PCS1GANA_SYM_PAUSE,
2318                                IXGBE_PCS1GANA_ASM_PAUSE,
2319                                IXGBE_PCS1GANA_SYM_PAUSE,
2320                                IXGBE_PCS1GANA_ASM_PAUSE);
2321
2322         return ret_val;
2323 }
2324
2325 /**
2326  *  ixgbe_fc_autoneg_backplane - Enable flow control IEEE clause 37
2327  *  @hw: pointer to hardware structure
2328  *
2329  *  Enable flow control according to IEEE clause 37.
2330  **/
2331 static int ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw)
2332 {
2333         u32 links2, anlp1_reg, autoc_reg, links;
2334         int ret_val;
2335
2336         /*
2337          * On backplane, bail out if
2338          * - backplane autoneg was not completed, or if
2339          * - we are 82599 and link partner is not AN enabled
2340          */
2341         links = IXGBE_READ_REG(hw, IXGBE_LINKS);
2342         if ((links & IXGBE_LINKS_KX_AN_COMP) == 0)
2343                 return -EIO;
2344
2345         if (hw->mac.type == ixgbe_mac_82599EB) {
2346                 links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2);
2347                 if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0)
2348                         return -EIO;
2349         }
2350         /*
2351          * Read the 10g AN autoc and LP ability registers and resolve
2352          * local flow control settings accordingly
2353          */
2354         autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
2355         anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);
2356
2357         ret_val = ixgbe_negotiate_fc(hw, autoc_reg,
2358                 anlp1_reg, IXGBE_AUTOC_SYM_PAUSE, IXGBE_AUTOC_ASM_PAUSE,
2359                 IXGBE_ANLP1_SYM_PAUSE, IXGBE_ANLP1_ASM_PAUSE);
2360
2361         return ret_val;
2362 }
2363
2364 /**
2365  *  ixgbe_fc_autoneg_copper - Enable flow control IEEE clause 37
2366  *  @hw: pointer to hardware structure
2367  *
2368  *  Enable flow control according to IEEE clause 37.
2369  **/
2370 static int ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw)
2371 {
2372         u16 technology_ability_reg = 0;
2373         u16 lp_technology_ability_reg = 0;
2374
2375         hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
2376                              MDIO_MMD_AN,
2377                              &technology_ability_reg);
2378         hw->phy.ops.read_reg(hw, MDIO_AN_LPA,
2379                              MDIO_MMD_AN,
2380                              &lp_technology_ability_reg);
2381
2382         return ixgbe_negotiate_fc(hw, (u32)technology_ability_reg,
2383                                   (u32)lp_technology_ability_reg,
2384                                   IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE,
2385                                   IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE);
2386 }
2387
2388 /**
2389  *  ixgbe_fc_autoneg - Configure flow control
2390  *  @hw: pointer to hardware structure
2391  *
2392  *  Compares our advertised flow control capabilities to those advertised by
2393  *  our link partner, and determines the proper flow control mode to use.
2394  **/
2395 void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
2396 {
2397         ixgbe_link_speed speed;
2398         int ret_val = -EIO;
2399         bool link_up;
2400
2401         /*
2402          * AN should have completed when the cable was plugged in.
2403          * Look for reasons to bail out.  Bail out if:
2404          * - FC autoneg is disabled, or if
2405          * - link is not up.
2406          *
2407          * Since we're being called from an LSC, link is already known to be up.
2408          * So use link_up_wait_to_complete=false.
2409          */
2410         if (hw->fc.disable_fc_autoneg)
2411                 goto out;
2412
2413         hw->mac.ops.check_link(hw, &speed, &link_up, false);
2414         if (!link_up)
2415                 goto out;
2416
2417         switch (hw->phy.media_type) {
2418         /* Autoneg flow control on fiber adapters */
2419         case ixgbe_media_type_fiber:
2420                 if (speed == IXGBE_LINK_SPEED_1GB_FULL)
2421                         ret_val = ixgbe_fc_autoneg_fiber(hw);
2422                 break;
2423
2424         /* Autoneg flow control on backplane adapters */
2425         case ixgbe_media_type_backplane:
2426                 ret_val = ixgbe_fc_autoneg_backplane(hw);
2427                 break;
2428
2429         /* Autoneg flow control on copper adapters */
2430         case ixgbe_media_type_copper:
2431                 if (ixgbe_device_supports_autoneg_fc(hw))
2432                         ret_val = ixgbe_fc_autoneg_copper(hw);
2433                 break;
2434
2435         default:
2436                 break;
2437         }
2438
2439 out:
2440         if (ret_val == 0) {
2441                 hw->fc.fc_was_autonegged = true;
2442         } else {
2443                 hw->fc.fc_was_autonegged = false;
2444                 hw->fc.current_mode = hw->fc.requested_mode;
2445         }
2446 }
2447
2448 /**
2449  * ixgbe_pcie_timeout_poll - Return number of times to poll for completion
2450  * @hw: pointer to hardware structure
2451  *
2452  * System-wide timeout range is encoded in PCIe Device Control2 register.
2453  *
2454  *  Add 10% to specified maximum and return the number of times to poll for
2455  *  completion timeout, in units of 100 microsec.  Never return less than
2456  *  800 = 80 millisec.
2457  **/
2458 static u32 ixgbe_pcie_timeout_poll(struct ixgbe_hw *hw)
2459 {
2460         s16 devctl2;
2461         u32 pollcnt;
2462
2463         devctl2 = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_CONTROL2);
2464         devctl2 &= IXGBE_PCIDEVCTRL2_TIMEO_MASK;
2465
2466         switch (devctl2) {
2467         case IXGBE_PCIDEVCTRL2_65_130ms:
2468                  pollcnt = 1300;         /* 130 millisec */
2469                 break;
2470         case IXGBE_PCIDEVCTRL2_260_520ms:
2471                 pollcnt = 5200;         /* 520 millisec */
2472                 break;
2473         case IXGBE_PCIDEVCTRL2_1_2s:
2474                 pollcnt = 20000;        /* 2 sec */
2475                 break;
2476         case IXGBE_PCIDEVCTRL2_4_8s:
2477                 pollcnt = 80000;        /* 8 sec */
2478                 break;
2479         case IXGBE_PCIDEVCTRL2_17_34s:
2480                 pollcnt = 34000;        /* 34 sec */
2481                 break;
2482         case IXGBE_PCIDEVCTRL2_50_100us:        /* 100 microsecs */
2483         case IXGBE_PCIDEVCTRL2_1_2ms:           /* 2 millisecs */
2484         case IXGBE_PCIDEVCTRL2_16_32ms:         /* 32 millisec */
2485         case IXGBE_PCIDEVCTRL2_16_32ms_def:     /* 32 millisec default */
2486         default:
2487                 pollcnt = 800;          /* 80 millisec minimum */
2488                 break;
2489         }
2490
2491         /* add 10% to spec maximum */
2492         return (pollcnt * 11) / 10;
2493 }
2494
2495 /**
2496  *  ixgbe_disable_pcie_primary - Disable PCI-express primary access
2497  *  @hw: pointer to hardware structure
2498  *
2499  *  Disables PCI-Express primary access and verifies there are no pending
2500  *  requests. -EALREADY is returned if primary disable
2501  *  bit hasn't caused the primary requests to be disabled, else 0
2502  *  is returned signifying primary requests disabled.
2503  **/
2504 static int ixgbe_disable_pcie_primary(struct ixgbe_hw *hw)
2505 {
2506         u32 i, poll;
2507         u16 value;
2508
2509         /* Always set this bit to ensure any future transactions are blocked */
2510         IXGBE_WRITE_REG(hw, IXGBE_CTRL, IXGBE_CTRL_GIO_DIS);
2511
2512         /* Poll for bit to read as set */
2513         for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
2514                 if (IXGBE_READ_REG(hw, IXGBE_CTRL) & IXGBE_CTRL_GIO_DIS)
2515                         break;
2516                 usleep_range(100, 120);
2517         }
2518         if (i >= IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT) {
2519                 hw_dbg(hw, "GIO disable did not set - requesting resets\n");
2520                 goto gio_disable_fail;
2521         }
2522
2523         /* Exit if primary requests are blocked */
2524         if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO) ||
2525             ixgbe_removed(hw->hw_addr))
2526                 return 0;
2527
2528         /* Poll for primary request bit to clear */
2529         for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
2530                 udelay(100);
2531                 if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO))
2532                         return 0;
2533         }
2534
2535         /*
2536          * Two consecutive resets are required via CTRL.RST per datasheet
2537          * 5.2.5.3.2 Primary Disable.  We set a flag to inform the reset routine
2538          * of this need.  The first reset prevents new primary requests from
2539          * being issued by our device.  We then must wait 1usec or more for any
2540          * remaining completions from the PCIe bus to trickle in, and then reset
2541          * again to clear out any effects they may have had on our device.
2542          */
2543         hw_dbg(hw, "GIO Primary Disable bit didn't clear - requesting resets\n");
2544 gio_disable_fail:
2545         hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
2546
2547         if (hw->mac.type >= ixgbe_mac_X550)
2548                 return 0;
2549
2550         /*
2551          * Before proceeding, make sure that the PCIe block does not have
2552          * transactions pending.
2553          */
2554         poll = ixgbe_pcie_timeout_poll(hw);
2555         for (i = 0; i < poll; i++) {
2556                 udelay(100);
2557                 value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS);
2558                 if (ixgbe_removed(hw->hw_addr))
2559                         return 0;
2560                 if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
2561                         return 0;
2562         }
2563
2564         hw_dbg(hw, "PCIe transaction pending bit also did not clear.\n");
2565         return -EALREADY;
2566 }
2567
2568 /**
2569  *  ixgbe_acquire_swfw_sync - Acquire SWFW semaphore
2570  *  @hw: pointer to hardware structure
2571  *  @mask: Mask to specify which semaphore to acquire
2572  *
2573  *  Acquires the SWFW semaphore through the GSSR register for the specified
2574  *  function (CSR, PHY0, PHY1, EEPROM, Flash)
2575  **/
2576 int ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u32 mask)
2577 {
2578         u32 gssr = 0;
2579         u32 swmask = mask;
2580         u32 fwmask = mask << 5;
2581         u32 timeout = 200;
2582         u32 i;
2583
2584         for (i = 0; i < timeout; i++) {
2585                 /*
2586                  * SW NVM semaphore bit is used for access to all
2587                  * SW_FW_SYNC bits (not just NVM)
2588                  */
2589                 if (ixgbe_get_eeprom_semaphore(hw))
2590                         return -EBUSY;
2591
2592                 gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
2593                 if (!(gssr & (fwmask | swmask))) {
2594                         gssr |= swmask;
2595                         IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr);
2596                         ixgbe_release_eeprom_semaphore(hw);
2597                         return 0;
2598                 } else {
2599                         /* Resource is currently in use by FW or SW */
2600                         ixgbe_release_eeprom_semaphore(hw);
2601                         usleep_range(5000, 10000);
2602                 }
2603         }
2604
2605         /* If time expired clear the bits holding the lock and retry */
2606         if (gssr & (fwmask | swmask))
2607                 ixgbe_release_swfw_sync(hw, gssr & (fwmask | swmask));
2608
2609         usleep_range(5000, 10000);
2610         return -EBUSY;
2611 }
2612
2613 /**
2614  *  ixgbe_release_swfw_sync - Release SWFW semaphore
2615  *  @hw: pointer to hardware structure
2616  *  @mask: Mask to specify which semaphore to release
2617  *
2618  *  Releases the SWFW semaphore through the GSSR register for the specified
2619  *  function (CSR, PHY0, PHY1, EEPROM, Flash)
2620  **/
2621 void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u32 mask)
2622 {
2623         u32 gssr;
2624         u32 swmask = mask;
2625
2626         ixgbe_get_eeprom_semaphore(hw);
2627
2628         gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
2629         gssr &= ~swmask;
2630         IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr);
2631
2632         ixgbe_release_eeprom_semaphore(hw);
2633 }
2634
2635 /**
2636  * prot_autoc_read_generic - Hides MAC differences needed for AUTOC read
2637  * @hw: pointer to hardware structure
2638  * @reg_val: Value we read from AUTOC
2639  * @locked: bool to indicate whether the SW/FW lock should be taken.  Never
2640  *          true in this the generic case.
2641  *
2642  * The default case requires no protection so just to the register read.
2643  **/
2644 int prot_autoc_read_generic(struct ixgbe_hw *hw, bool *locked, u32 *reg_val)
2645 {
2646         *locked = false;
2647         *reg_val = IXGBE_READ_REG(hw, IXGBE_AUTOC);
2648         return 0;
2649 }
2650
2651 /**
2652  * prot_autoc_write_generic - Hides MAC differences needed for AUTOC write
2653  * @hw: pointer to hardware structure
2654  * @reg_val: value to write to AUTOC
2655  * @locked: bool to indicate whether the SW/FW lock was already taken by
2656  *          previous read.
2657  **/
2658 int prot_autoc_write_generic(struct ixgbe_hw *hw, u32 reg_val, bool locked)
2659 {
2660         IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_val);
2661         return 0;
2662 }
2663
2664 /**
2665  *  ixgbe_disable_rx_buff_generic - Stops the receive data path
2666  *  @hw: pointer to hardware structure
2667  *
2668  *  Stops the receive data path and waits for the HW to internally
2669  *  empty the Rx security block.
2670  **/
2671 int ixgbe_disable_rx_buff_generic(struct ixgbe_hw *hw)
2672 {
2673 #define IXGBE_MAX_SECRX_POLL 40
2674         int i;
2675         int secrxreg;
2676
2677         secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
2678         secrxreg |= IXGBE_SECRXCTRL_RX_DIS;
2679         IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
2680         for (i = 0; i < IXGBE_MAX_SECRX_POLL; i++) {
2681                 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXSTAT);
2682                 if (secrxreg & IXGBE_SECRXSTAT_SECRX_RDY)
2683                         break;
2684                 else
2685                         /* Use interrupt-safe sleep just in case */
2686                         udelay(1000);
2687         }
2688
2689         /* For informational purposes only */
2690         if (i >= IXGBE_MAX_SECRX_POLL)
2691                 hw_dbg(hw, "Rx unit being enabled before security path fully disabled. Continuing with init.\n");
2692
2693         return 0;
2694
2695 }
2696
2697 /**
2698  *  ixgbe_enable_rx_buff_generic - Enables the receive data path
2699  *  @hw: pointer to hardware structure
2700  *
2701  *  Enables the receive data path
2702  **/
2703 int ixgbe_enable_rx_buff_generic(struct ixgbe_hw *hw)
2704 {
2705         u32 secrxreg;
2706
2707         secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
2708         secrxreg &= ~IXGBE_SECRXCTRL_RX_DIS;
2709         IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
2710         IXGBE_WRITE_FLUSH(hw);
2711
2712         return 0;
2713 }
2714
2715 /**
2716  *  ixgbe_enable_rx_dma_generic - Enable the Rx DMA unit
2717  *  @hw: pointer to hardware structure
2718  *  @regval: register value to write to RXCTRL
2719  *
2720  *  Enables the Rx DMA unit
2721  **/
2722 int ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval)
2723 {
2724         if (regval & IXGBE_RXCTRL_RXEN)
2725                 hw->mac.ops.enable_rx(hw);
2726         else
2727                 hw->mac.ops.disable_rx(hw);
2728
2729         return 0;
2730 }
2731
2732 /**
2733  *  ixgbe_blink_led_start_generic - Blink LED based on index.
2734  *  @hw: pointer to hardware structure
2735  *  @index: led number to blink
2736  **/
2737 int ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index)
2738 {
2739         u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
2740         u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
2741         ixgbe_link_speed speed = 0;
2742         bool link_up = false;
2743         bool locked = false;
2744         int ret_val;
2745
2746         if (index > 3)
2747                 return -EINVAL;
2748
2749         /*
2750          * Link must be up to auto-blink the LEDs;
2751          * Force it if link is down.
2752          */
2753         hw->mac.ops.check_link(hw, &speed, &link_up, false);
2754
2755         if (!link_up) {
2756                 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
2757                 if (ret_val)
2758                         return ret_val;
2759
2760                 autoc_reg |= IXGBE_AUTOC_AN_RESTART;
2761                 autoc_reg |= IXGBE_AUTOC_FLU;
2762
2763                 ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked);
2764                 if (ret_val)
2765                         return ret_val;
2766
2767                 IXGBE_WRITE_FLUSH(hw);
2768
2769                 usleep_range(10000, 20000);
2770         }
2771
2772         led_reg &= ~IXGBE_LED_MODE_MASK(index);
2773         led_reg |= IXGBE_LED_BLINK(index);
2774         IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
2775         IXGBE_WRITE_FLUSH(hw);
2776
2777         return 0;
2778 }
2779
2780 /**
2781  *  ixgbe_blink_led_stop_generic - Stop blinking LED based on index.
2782  *  @hw: pointer to hardware structure
2783  *  @index: led number to stop blinking
2784  **/
2785 int ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index)
2786 {
2787         u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
2788         bool locked = false;
2789         u32 autoc_reg = 0;
2790         int ret_val;
2791
2792         if (index > 3)
2793                 return -EINVAL;
2794
2795         ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
2796         if (ret_val)
2797                 return ret_val;
2798
2799         autoc_reg &= ~IXGBE_AUTOC_FLU;
2800         autoc_reg |= IXGBE_AUTOC_AN_RESTART;
2801
2802         ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked);
2803         if (ret_val)
2804                 return ret_val;
2805
2806         led_reg &= ~IXGBE_LED_MODE_MASK(index);
2807         led_reg &= ~IXGBE_LED_BLINK(index);
2808         led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index);
2809         IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
2810         IXGBE_WRITE_FLUSH(hw);
2811
2812         return 0;
2813 }
2814
2815 /**
2816  *  ixgbe_get_san_mac_addr_offset - Get SAN MAC address offset from the EEPROM
2817  *  @hw: pointer to hardware structure
2818  *  @san_mac_offset: SAN MAC address offset
2819  *
2820  *  This function will read the EEPROM location for the SAN MAC address
2821  *  pointer, and returns the value at that location.  This is used in both
2822  *  get and set mac_addr routines.
2823  **/
2824 static int ixgbe_get_san_mac_addr_offset(struct ixgbe_hw *hw,
2825                                          u16 *san_mac_offset)
2826 {
2827         int ret_val;
2828
2829         /*
2830          * First read the EEPROM pointer to see if the MAC addresses are
2831          * available.
2832          */
2833         ret_val = hw->eeprom.ops.read(hw, IXGBE_SAN_MAC_ADDR_PTR,
2834                                       san_mac_offset);
2835         if (ret_val)
2836                 hw_err(hw, "eeprom read at offset %d failed\n",
2837                        IXGBE_SAN_MAC_ADDR_PTR);
2838
2839         return ret_val;
2840 }
2841
2842 /**
2843  *  ixgbe_get_san_mac_addr_generic - SAN MAC address retrieval from the EEPROM
2844  *  @hw: pointer to hardware structure
2845  *  @san_mac_addr: SAN MAC address
2846  *
2847  *  Reads the SAN MAC address from the EEPROM, if it's available.  This is
2848  *  per-port, so set_lan_id() must be called before reading the addresses.
2849  *  set_lan_id() is called by identify_sfp(), but this cannot be relied
2850  *  upon for non-SFP connections, so we must call it here.
2851  **/
2852 int ixgbe_get_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr)
2853 {
2854         u16 san_mac_data, san_mac_offset;
2855         int ret_val;
2856         u8 i;
2857
2858         /*
2859          * First read the EEPROM pointer to see if the MAC addresses are
2860          * available.  If they're not, no point in calling set_lan_id() here.
2861          */
2862         ret_val = ixgbe_get_san_mac_addr_offset(hw, &san_mac_offset);
2863         if (ret_val || san_mac_offset == 0 || san_mac_offset == 0xFFFF)
2864
2865                 goto san_mac_addr_clr;
2866
2867         /* make sure we know which port we need to program */
2868         hw->mac.ops.set_lan_id(hw);
2869         /* apply the port offset to the address offset */
2870         (hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) :
2871                          (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET);
2872         for (i = 0; i < 3; i++) {
2873                 ret_val = hw->eeprom.ops.read(hw, san_mac_offset,
2874                                               &san_mac_data);
2875                 if (ret_val) {
2876                         hw_err(hw, "eeprom read at offset %d failed\n",
2877                                san_mac_offset);
2878                         goto san_mac_addr_clr;
2879                 }
2880                 san_mac_addr[i * 2] = (u8)(san_mac_data);
2881                 san_mac_addr[i * 2 + 1] = (u8)(san_mac_data >> 8);
2882                 san_mac_offset++;
2883         }
2884         return 0;
2885
2886 san_mac_addr_clr:
2887         /* No addresses available in this EEPROM.  It's not necessarily an
2888          * error though, so just wipe the local address and return.
2889          */
2890         for (i = 0; i < 6; i++)
2891                 san_mac_addr[i] = 0xFF;
2892         return ret_val;
2893 }
2894
2895 /**
2896  *  ixgbe_get_pcie_msix_count_generic - Gets MSI-X vector count
2897  *  @hw: pointer to hardware structure
2898  *
2899  *  Read PCIe configuration space, and get the MSI-X vector count from
2900  *  the capabilities table.
2901  **/
2902 u16 ixgbe_get_pcie_msix_count_generic(struct ixgbe_hw *hw)
2903 {
2904         u16 msix_count;
2905         u16 max_msix_count;
2906         u16 pcie_offset;
2907
2908         switch (hw->mac.type) {
2909         case ixgbe_mac_82598EB:
2910                 pcie_offset = IXGBE_PCIE_MSIX_82598_CAPS;
2911                 max_msix_count = IXGBE_MAX_MSIX_VECTORS_82598;
2912                 break;
2913         case ixgbe_mac_82599EB:
2914         case ixgbe_mac_X540:
2915         case ixgbe_mac_X550:
2916         case ixgbe_mac_X550EM_x:
2917         case ixgbe_mac_x550em_a:
2918                 pcie_offset = IXGBE_PCIE_MSIX_82599_CAPS;
2919                 max_msix_count = IXGBE_MAX_MSIX_VECTORS_82599;
2920                 break;
2921         default:
2922                 return 1;
2923         }
2924
2925         msix_count = ixgbe_read_pci_cfg_word(hw, pcie_offset);
2926         if (ixgbe_removed(hw->hw_addr))
2927                 msix_count = 0;
2928         msix_count &= IXGBE_PCIE_MSIX_TBL_SZ_MASK;
2929
2930         /* MSI-X count is zero-based in HW */
2931         msix_count++;
2932
2933         if (msix_count > max_msix_count)
2934                 msix_count = max_msix_count;
2935
2936         return msix_count;
2937 }
2938
2939 /**
2940  *  ixgbe_clear_vmdq_generic - Disassociate a VMDq pool index from a rx address
2941  *  @hw: pointer to hardware struct
2942  *  @rar: receive address register index to disassociate
2943  *  @vmdq: VMDq pool index to remove from the rar
2944  **/
2945 int ixgbe_clear_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
2946 {
2947         u32 mpsar_lo, mpsar_hi;
2948         u32 rar_entries = hw->mac.num_rar_entries;
2949
2950         /* Make sure we are using a valid rar index range */
2951         if (rar >= rar_entries) {
2952                 hw_dbg(hw, "RAR index %d is out of range.\n", rar);
2953                 return -EINVAL;
2954         }
2955
2956         mpsar_lo = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar));
2957         mpsar_hi = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar));
2958
2959         if (ixgbe_removed(hw->hw_addr))
2960                 return 0;
2961
2962         if (!mpsar_lo && !mpsar_hi)
2963                 return 0;
2964
2965         if (vmdq == IXGBE_CLEAR_VMDQ_ALL) {
2966                 if (mpsar_lo) {
2967                         IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0);
2968                         mpsar_lo = 0;
2969                 }
2970                 if (mpsar_hi) {
2971                         IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0);
2972                         mpsar_hi = 0;
2973                 }
2974         } else if (vmdq < 32) {
2975                 mpsar_lo &= ~BIT(vmdq);
2976                 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar_lo);
2977         } else {
2978                 mpsar_hi &= ~BIT(vmdq - 32);
2979                 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar_hi);
2980         }
2981
2982         /* was that the last pool using this rar? */
2983         if (mpsar_lo == 0 && mpsar_hi == 0 &&
2984             rar != 0 && rar != hw->mac.san_mac_rar_index)
2985                 hw->mac.ops.clear_rar(hw, rar);
2986
2987         return 0;
2988 }
2989
2990 /**
2991  *  ixgbe_set_vmdq_generic - Associate a VMDq pool index with a rx address
2992  *  @hw: pointer to hardware struct
2993  *  @rar: receive address register index to associate with a VMDq index
2994  *  @vmdq: VMDq pool index
2995  **/
2996 int ixgbe_set_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
2997 {
2998         u32 mpsar;
2999         u32 rar_entries = hw->mac.num_rar_entries;
3000
3001         /* Make sure we are using a valid rar index range */
3002         if (rar >= rar_entries) {
3003                 hw_dbg(hw, "RAR index %d is out of range.\n", rar);
3004                 return -EINVAL;
3005         }
3006
3007         if (vmdq < 32) {
3008                 mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar));
3009                 mpsar |= BIT(vmdq);
3010                 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar);
3011         } else {
3012                 mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar));
3013                 mpsar |= BIT(vmdq - 32);
3014                 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar);
3015         }
3016         return 0;
3017 }
3018
3019 /**
3020  *  ixgbe_set_vmdq_san_mac_generic - Associate VMDq pool index with a rx address
3021  *  @hw: pointer to hardware struct
3022  *  @vmdq: VMDq pool index
3023  *
3024  *  This function should only be involved in the IOV mode.
3025  *  In IOV mode, Default pool is next pool after the number of
3026  *  VFs advertized and not 0.
3027  *  MPSAR table needs to be updated for SAN_MAC RAR [hw->mac.san_mac_rar_index]
3028  **/
3029 int ixgbe_set_vmdq_san_mac_generic(struct ixgbe_hw *hw, u32 vmdq)
3030 {
3031         u32 rar = hw->mac.san_mac_rar_index;
3032
3033         if (vmdq < 32) {
3034                 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), BIT(vmdq));
3035                 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0);
3036         } else {
3037                 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0);
3038                 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), BIT(vmdq - 32));
3039         }
3040
3041         return 0;
3042 }
3043
3044 /**
3045  *  ixgbe_init_uta_tables_generic - Initialize the Unicast Table Array
3046  *  @hw: pointer to hardware structure
3047  **/
3048 int ixgbe_init_uta_tables_generic(struct ixgbe_hw *hw)
3049 {
3050         int i;
3051
3052         for (i = 0; i < 128; i++)
3053                 IXGBE_WRITE_REG(hw, IXGBE_UTA(i), 0);
3054
3055         return 0;
3056 }
3057
3058 /**
3059  *  ixgbe_find_vlvf_slot - find the vlanid or the first empty slot
3060  *  @hw: pointer to hardware structure
3061  *  @vlan: VLAN id to write to VLAN filter
3062  *  @vlvf_bypass: true to find vlanid only, false returns first empty slot if
3063  *                vlanid not found
3064  *
3065  *  return the VLVF index where this VLAN id should be placed
3066  *
3067  **/
3068 static int ixgbe_find_vlvf_slot(struct ixgbe_hw *hw, u32 vlan, bool vlvf_bypass)
3069 {
3070         int regindex, first_empty_slot;
3071         u32 bits;
3072
3073         /* short cut the special case */
3074         if (vlan == 0)
3075                 return 0;
3076
3077         /* if vlvf_bypass is set we don't want to use an empty slot, we
3078          * will simply bypass the VLVF if there are no entries present in the
3079          * VLVF that contain our VLAN
3080          */
3081         first_empty_slot = vlvf_bypass ? -ENOSPC : 0;
3082
3083         /* add VLAN enable bit for comparison */
3084         vlan |= IXGBE_VLVF_VIEN;
3085
3086         /* Search for the vlan id in the VLVF entries. Save off the first empty
3087          * slot found along the way.
3088          *
3089          * pre-decrement loop covering (IXGBE_VLVF_ENTRIES - 1) .. 1
3090          */
3091         for (regindex = IXGBE_VLVF_ENTRIES; --regindex;) {
3092                 bits = IXGBE_READ_REG(hw, IXGBE_VLVF(regindex));
3093                 if (bits == vlan)
3094                         return regindex;
3095                 if (!first_empty_slot && !bits)
3096                         first_empty_slot = regindex;
3097         }
3098
3099         /* If we are here then we didn't find the VLAN.  Return first empty
3100          * slot we found during our search, else error.
3101          */
3102         if (!first_empty_slot)
3103                 hw_dbg(hw, "No space in VLVF.\n");
3104
3105         return first_empty_slot ? : -ENOSPC;
3106 }
3107
3108 /**
3109  *  ixgbe_set_vfta_generic - Set VLAN filter table
3110  *  @hw: pointer to hardware structure
3111  *  @vlan: VLAN id to write to VLAN filter
3112  *  @vind: VMDq output index that maps queue to VLAN id in VFVFB
3113  *  @vlan_on: boolean flag to turn on/off VLAN in VFVF
3114  *  @vlvf_bypass: boolean flag indicating updating default pool is okay
3115  *
3116  *  Turn on/off specified VLAN in the VLAN filter table.
3117  **/
3118 int ixgbe_set_vfta_generic(struct ixgbe_hw *hw, u32 vlan, u32 vind,
3119                            bool vlan_on, bool vlvf_bypass)
3120 {
3121         u32 regidx, vfta_delta, vfta, bits;
3122         int vlvf_index;
3123
3124         if ((vlan > 4095) || (vind > 63))
3125                 return -EINVAL;
3126
3127         /*
3128          * this is a 2 part operation - first the VFTA, then the
3129          * VLVF and VLVFB if VT Mode is set
3130          * We don't write the VFTA until we know the VLVF part succeeded.
3131          */
3132
3133         /* Part 1
3134          * The VFTA is a bitstring made up of 128 32-bit registers
3135          * that enable the particular VLAN id, much like the MTA:
3136          *    bits[11-5]: which register
3137          *    bits[4-0]:  which bit in the register
3138          */
3139         regidx = vlan / 32;
3140         vfta_delta = BIT(vlan % 32);
3141         vfta = IXGBE_READ_REG(hw, IXGBE_VFTA(regidx));
3142
3143         /* vfta_delta represents the difference between the current value
3144          * of vfta and the value we want in the register.  Since the diff
3145          * is an XOR mask we can just update vfta using an XOR.
3146          */
3147         vfta_delta &= vlan_on ? ~vfta : vfta;
3148         vfta ^= vfta_delta;
3149
3150         /* Part 2
3151          * If VT Mode is set
3152          *   Either vlan_on
3153          *     make sure the vlan is in VLVF
3154          *     set the vind bit in the matching VLVFB
3155          *   Or !vlan_on
3156          *     clear the pool bit and possibly the vind
3157          */
3158         if (!(IXGBE_READ_REG(hw, IXGBE_VT_CTL) & IXGBE_VT_CTL_VT_ENABLE))
3159                 goto vfta_update;
3160
3161         vlvf_index = ixgbe_find_vlvf_slot(hw, vlan, vlvf_bypass);
3162         if (vlvf_index < 0) {
3163                 if (vlvf_bypass)
3164                         goto vfta_update;
3165                 return vlvf_index;
3166         }
3167
3168         bits = IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32));
3169
3170         /* set the pool bit */
3171         bits |= BIT(vind % 32);
3172         if (vlan_on)
3173                 goto vlvf_update;
3174
3175         /* clear the pool bit */
3176         bits ^= BIT(vind % 32);
3177
3178         if (!bits &&
3179             !IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + 1 - vind / 32))) {
3180                 /* Clear VFTA first, then disable VLVF.  Otherwise
3181                  * we run the risk of stray packets leaking into
3182                  * the PF via the default pool
3183                  */
3184                 if (vfta_delta)
3185                         IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta);
3186
3187                 /* disable VLVF and clear remaining bit from pool */
3188                 IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), 0);
3189                 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), 0);
3190
3191                 return 0;
3192         }
3193
3194         /* If there are still bits set in the VLVFB registers
3195          * for the VLAN ID indicated we need to see if the
3196          * caller is requesting that we clear the VFTA entry bit.
3197          * If the caller has requested that we clear the VFTA
3198          * entry bit but there are still pools/VFs using this VLAN
3199          * ID entry then ignore the request.  We're not worried
3200          * about the case where we're turning the VFTA VLAN ID
3201          * entry bit on, only when requested to turn it off as
3202          * there may be multiple pools and/or VFs using the
3203          * VLAN ID entry.  In that case we cannot clear the
3204          * VFTA bit until all pools/VFs using that VLAN ID have also
3205          * been cleared.  This will be indicated by "bits" being
3206          * zero.
3207          */
3208         vfta_delta = 0;
3209
3210 vlvf_update:
3211         /* record pool change and enable VLAN ID if not already enabled */
3212         IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), bits);
3213         IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), IXGBE_VLVF_VIEN | vlan);
3214
3215 vfta_update:
3216         /* Update VFTA now that we are ready for traffic */
3217         if (vfta_delta)
3218                 IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta);
3219
3220         return 0;
3221 }
3222
3223 /**
3224  *  ixgbe_clear_vfta_generic - Clear VLAN filter table
3225  *  @hw: pointer to hardware structure
3226  *
3227  *  Clears the VLAN filter table, and the VMDq index associated with the filter
3228  **/
3229 int ixgbe_clear_vfta_generic(struct ixgbe_hw *hw)
3230 {
3231         u32 offset;
3232
3233         for (offset = 0; offset < hw->mac.vft_size; offset++)
3234                 IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0);
3235
3236         for (offset = 0; offset < IXGBE_VLVF_ENTRIES; offset++) {
3237                 IXGBE_WRITE_REG(hw, IXGBE_VLVF(offset), 0);
3238                 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2), 0);
3239                 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2 + 1), 0);
3240         }
3241
3242         return 0;
3243 }
3244
3245 /**
3246  *  ixgbe_need_crosstalk_fix - Determine if we need to do cross talk fix
3247  *  @hw: pointer to hardware structure
3248  *
3249  *  Contains the logic to identify if we need to verify link for the
3250  *  crosstalk fix
3251  **/
3252 static bool ixgbe_need_crosstalk_fix(struct ixgbe_hw *hw)
3253 {
3254         /* Does FW say we need the fix */
3255         if (!hw->need_crosstalk_fix)
3256                 return false;
3257
3258         /* Only consider SFP+ PHYs i.e. media type fiber */
3259         switch (hw->mac.ops.get_media_type(hw)) {
3260         case ixgbe_media_type_fiber:
3261         case ixgbe_media_type_fiber_qsfp:
3262                 break;
3263         default:
3264                 return false;
3265         }
3266
3267         return true;
3268 }
3269
3270 /**
3271  *  ixgbe_check_mac_link_generic - Determine link and speed status
3272  *  @hw: pointer to hardware structure
3273  *  @speed: pointer to link speed
3274  *  @link_up: true when link is up
3275  *  @link_up_wait_to_complete: bool used to wait for link up or not
3276  *
3277  *  Reads the links register to determine if link is up and the current speed
3278  **/
3279 int ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
3280                                  bool *link_up, bool link_up_wait_to_complete)
3281 {
3282         bool crosstalk_fix_active = ixgbe_need_crosstalk_fix(hw);
3283         u32 links_reg, links_orig;
3284         u32 i;
3285
3286         /* If Crosstalk fix enabled do the sanity check of making sure
3287          * the SFP+ cage is full.
3288          */
3289         if (crosstalk_fix_active) {
3290                 u32 sfp_cage_full;
3291
3292                 switch (hw->mac.type) {
3293                 case ixgbe_mac_82599EB:
3294                         sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
3295                                         IXGBE_ESDP_SDP2;
3296                         break;
3297                 case ixgbe_mac_X550EM_x:
3298                 case ixgbe_mac_x550em_a:
3299                         sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
3300                                         IXGBE_ESDP_SDP0;
3301                         break;
3302                 default:
3303                         /* sanity check - No SFP+ devices here */
3304                         sfp_cage_full = false;
3305                         break;
3306                 }
3307
3308                 if (!sfp_cage_full) {
3309                         *link_up = false;
3310                         *speed = IXGBE_LINK_SPEED_UNKNOWN;
3311                         return 0;
3312                 }
3313         }
3314
3315         /* clear the old state */
3316         links_orig = IXGBE_READ_REG(hw, IXGBE_LINKS);
3317
3318         links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
3319
3320         if (links_orig != links_reg) {
3321                 hw_dbg(hw, "LINKS changed from %08X to %08X\n",
3322                        links_orig, links_reg);
3323         }
3324
3325         if (link_up_wait_to_complete) {
3326                 for (i = 0; i < IXGBE_LINK_UP_TIME; i++) {
3327                         if (links_reg & IXGBE_LINKS_UP) {
3328                                 *link_up = true;
3329                                 break;
3330                         } else {
3331                                 *link_up = false;
3332                         }
3333                         msleep(100);
3334                         links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
3335                 }
3336         } else {
3337                 if (links_reg & IXGBE_LINKS_UP) {
3338                         if (crosstalk_fix_active) {
3339                                 /* Check the link state again after a delay
3340                                  * to filter out spurious link up
3341                                  * notifications.
3342                                  */
3343                                 mdelay(5);
3344                                 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
3345                                 if (!(links_reg & IXGBE_LINKS_UP)) {
3346                                         *link_up = false;
3347                                         *speed = IXGBE_LINK_SPEED_UNKNOWN;
3348                                         return 0;
3349                                 }
3350                         }
3351                         *link_up = true;
3352                 } else {
3353                         *link_up = false;
3354                 }
3355         }
3356
3357         switch (links_reg & IXGBE_LINKS_SPEED_82599) {
3358         case IXGBE_LINKS_SPEED_10G_82599:
3359                 if ((hw->mac.type >= ixgbe_mac_X550) &&
3360                     (links_reg & IXGBE_LINKS_SPEED_NON_STD))
3361                         *speed = IXGBE_LINK_SPEED_2_5GB_FULL;
3362                 else
3363                         *speed = IXGBE_LINK_SPEED_10GB_FULL;
3364                 break;
3365         case IXGBE_LINKS_SPEED_1G_82599:
3366                 *speed = IXGBE_LINK_SPEED_1GB_FULL;
3367                 break;
3368         case IXGBE_LINKS_SPEED_100_82599:
3369                 if ((hw->mac.type >= ixgbe_mac_X550) &&
3370                     (links_reg & IXGBE_LINKS_SPEED_NON_STD))
3371                         *speed = IXGBE_LINK_SPEED_5GB_FULL;
3372                 else
3373                         *speed = IXGBE_LINK_SPEED_100_FULL;
3374                 break;
3375         case IXGBE_LINKS_SPEED_10_X550EM_A:
3376                 *speed = IXGBE_LINK_SPEED_UNKNOWN;
3377                 if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
3378                     hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) {
3379                         *speed = IXGBE_LINK_SPEED_10_FULL;
3380                 }
3381                 break;
3382         default:
3383                 *speed = IXGBE_LINK_SPEED_UNKNOWN;
3384         }
3385
3386         return 0;
3387 }
3388
3389 /**
3390  *  ixgbe_get_wwn_prefix_generic - Get alternative WWNN/WWPN prefix from
3391  *  the EEPROM
3392  *  @hw: pointer to hardware structure
3393  *  @wwnn_prefix: the alternative WWNN prefix
3394  *  @wwpn_prefix: the alternative WWPN prefix
3395  *
3396  *  This function will read the EEPROM from the alternative SAN MAC address
3397  *  block to check the support for the alternative WWNN/WWPN prefix support.
3398  **/
3399 int ixgbe_get_wwn_prefix_generic(struct ixgbe_hw *hw, u16 *wwnn_prefix,
3400                                  u16 *wwpn_prefix)
3401 {
3402         u16 offset, caps;
3403         u16 alt_san_mac_blk_offset;
3404
3405         /* clear output first */
3406         *wwnn_prefix = 0xFFFF;
3407         *wwpn_prefix = 0xFFFF;
3408
3409         /* check if alternative SAN MAC is supported */
3410         offset = IXGBE_ALT_SAN_MAC_ADDR_BLK_PTR;
3411         if (hw->eeprom.ops.read(hw, offset, &alt_san_mac_blk_offset))
3412                 goto wwn_prefix_err;
3413
3414         if ((alt_san_mac_blk_offset == 0) ||
3415             (alt_san_mac_blk_offset == 0xFFFF))
3416                 return 0;
3417
3418         /* check capability in alternative san mac address block */
3419         offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET;
3420         if (hw->eeprom.ops.read(hw, offset, &caps))
3421                 goto wwn_prefix_err;
3422         if (!(caps & IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN))
3423                 return 0;
3424
3425         /* get the corresponding prefix for WWNN/WWPN */
3426         offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET;
3427         if (hw->eeprom.ops.read(hw, offset, wwnn_prefix))
3428                 hw_err(hw, "eeprom read at offset %d failed\n", offset);
3429
3430         offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET;
3431         if (hw->eeprom.ops.read(hw, offset, wwpn_prefix))
3432                 goto wwn_prefix_err;
3433
3434         return 0;
3435
3436 wwn_prefix_err:
3437         hw_err(hw, "eeprom read at offset %d failed\n", offset);
3438         return 0;
3439 }
3440
3441 /**
3442  *  ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing
3443  *  @hw: pointer to hardware structure
3444  *  @enable: enable or disable switch for MAC anti-spoofing
3445  *  @vf: Virtual Function pool - VF Pool to set for MAC anti-spoofing
3446  *
3447  **/
3448 void ixgbe_set_mac_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)
3449 {
3450         int vf_target_reg = vf >> 3;
3451         int vf_target_shift = vf % 8;
3452         u32 pfvfspoof;
3453
3454         if (hw->mac.type == ixgbe_mac_82598EB)
3455                 return;
3456
3457         pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
3458         if (enable)
3459                 pfvfspoof |= BIT(vf_target_shift);
3460         else
3461                 pfvfspoof &= ~BIT(vf_target_shift);
3462         IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof);
3463 }
3464
3465 /**
3466  *  ixgbe_set_vlan_anti_spoofing - Enable/Disable VLAN anti-spoofing
3467  *  @hw: pointer to hardware structure
3468  *  @enable: enable or disable switch for VLAN anti-spoofing
3469  *  @vf: Virtual Function pool - VF Pool to set for VLAN anti-spoofing
3470  *
3471  **/
3472 void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)
3473 {
3474         int vf_target_reg = vf >> 3;
3475         int vf_target_shift = vf % 8 + IXGBE_SPOOF_VLANAS_SHIFT;
3476         u32 pfvfspoof;
3477
3478         if (hw->mac.type == ixgbe_mac_82598EB)
3479                 return;
3480
3481         pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
3482         if (enable)
3483                 pfvfspoof |= BIT(vf_target_shift);
3484         else
3485                 pfvfspoof &= ~BIT(vf_target_shift);
3486         IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof);
3487 }
3488
3489 /**
3490  *  ixgbe_get_device_caps_generic - Get additional device capabilities
3491  *  @hw: pointer to hardware structure
3492  *  @device_caps: the EEPROM word with the extra device capabilities
3493  *
3494  *  This function will read the EEPROM location for the device capabilities,
3495  *  and return the word through device_caps.
3496  **/
3497 int ixgbe_get_device_caps_generic(struct ixgbe_hw *hw, u16 *device_caps)
3498 {
3499         hw->eeprom.ops.read(hw, IXGBE_DEVICE_CAPS, device_caps);
3500
3501         return 0;
3502 }
3503
3504 /**
3505  * ixgbe_set_rxpba_generic - Initialize RX packet buffer
3506  * @hw: pointer to hardware structure
3507  * @num_pb: number of packet buffers to allocate
3508  * @headroom: reserve n KB of headroom
3509  * @strategy: packet buffer allocation strategy
3510  **/
3511 void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw,
3512                              int num_pb,
3513                              u32 headroom,
3514                              int strategy)
3515 {
3516         u32 pbsize = hw->mac.rx_pb_size;
3517         int i = 0;
3518         u32 rxpktsize, txpktsize, txpbthresh;
3519
3520         /* Reserve headroom */
3521         pbsize -= headroom;
3522
3523         if (!num_pb)
3524                 num_pb = 1;
3525
3526         /* Divide remaining packet buffer space amongst the number
3527          * of packet buffers requested using supplied strategy.
3528          */
3529         switch (strategy) {
3530         case (PBA_STRATEGY_WEIGHTED):
3531                 /* pba_80_48 strategy weight first half of packet buffer with
3532                  * 5/8 of the packet buffer space.
3533                  */
3534                 rxpktsize = ((pbsize * 5 * 2) / (num_pb * 8));
3535                 pbsize -= rxpktsize * (num_pb / 2);
3536                 rxpktsize <<= IXGBE_RXPBSIZE_SHIFT;
3537                 for (; i < (num_pb / 2); i++)
3538                         IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
3539                 fallthrough; /* configure remaining packet buffers */
3540         case (PBA_STRATEGY_EQUAL):
3541                 /* Divide the remaining Rx packet buffer evenly among the TCs */
3542                 rxpktsize = (pbsize / (num_pb - i)) << IXGBE_RXPBSIZE_SHIFT;
3543                 for (; i < num_pb; i++)
3544                         IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
3545                 break;
3546         default:
3547                 break;
3548         }
3549
3550         /*
3551          * Setup Tx packet buffer and threshold equally for all TCs
3552          * TXPBTHRESH register is set in K so divide by 1024 and subtract
3553          * 10 since the largest packet we support is just over 9K.
3554          */
3555         txpktsize = IXGBE_TXPBSIZE_MAX / num_pb;
3556         txpbthresh = (txpktsize / 1024) - IXGBE_TXPKT_SIZE_MAX;
3557         for (i = 0; i < num_pb; i++) {
3558                 IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), txpktsize);
3559                 IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), txpbthresh);
3560         }
3561
3562         /* Clear unused TCs, if any, to zero buffer size*/
3563         for (; i < IXGBE_MAX_PB; i++) {
3564                 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0);
3565                 IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), 0);
3566                 IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), 0);
3567         }
3568 }
3569
3570 /**
3571  *  ixgbe_calculate_checksum - Calculate checksum for buffer
3572  *  @buffer: pointer to EEPROM
3573  *  @length: size of EEPROM to calculate a checksum for
3574  *
3575  *  Calculates the checksum for some buffer on a specified length.  The
3576  *  checksum calculated is returned.
3577  **/
3578 u8 ixgbe_calculate_checksum(u8 *buffer, u32 length)
3579 {
3580         u32 i;
3581         u8 sum = 0;
3582
3583         if (!buffer)
3584                 return 0;
3585
3586         for (i = 0; i < length; i++)
3587                 sum += buffer[i];
3588
3589         return (u8) (0 - sum);
3590 }
3591
3592 /**
3593  *  ixgbe_hic_unlocked - Issue command to manageability block unlocked
3594  *  @hw: pointer to the HW structure
3595  *  @buffer: command to write and where the return status will be placed
3596  *  @length: length of buffer, must be multiple of 4 bytes
3597  *  @timeout: time in ms to wait for command completion
3598  *
3599  *  Communicates with the manageability block. On success return 0
3600  *  else returns semaphore error when encountering an error acquiring
3601  *  semaphore, -EINVAL when incorrect parameters passed or -EIO when
3602  *  command fails.
3603  *
3604  *  This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held
3605  *  by the caller.
3606  **/
3607 int ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length,
3608                        u32 timeout)
3609 {
3610         u32 hicr, i, fwsts;
3611         u16 dword_len;
3612
3613         if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
3614                 hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
3615                 return -EINVAL;
3616         }
3617
3618         /* Set bit 9 of FWSTS clearing FW reset indication */
3619         fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS);
3620         IXGBE_WRITE_REG(hw, IXGBE_FWSTS, fwsts | IXGBE_FWSTS_FWRI);
3621
3622         /* Check that the host interface is enabled. */
3623         hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
3624         if (!(hicr & IXGBE_HICR_EN)) {
3625                 hw_dbg(hw, "IXGBE_HOST_EN bit disabled.\n");
3626                 return -EIO;
3627         }
3628
3629         /* Calculate length in DWORDs. We must be DWORD aligned */
3630         if (length % sizeof(u32)) {
3631                 hw_dbg(hw, "Buffer length failure, not aligned to dword");
3632                 return -EINVAL;
3633         }
3634
3635         dword_len = length >> 2;
3636
3637         /* The device driver writes the relevant command block
3638          * into the ram area.
3639          */
3640         for (i = 0; i < dword_len; i++)
3641                 IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG,
3642                                       i, (__force u32)cpu_to_le32(buffer[i]));
3643
3644         /* Setting this bit tells the ARC that a new command is pending. */
3645         IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C);
3646
3647         for (i = 0; i < timeout; i++) {
3648                 hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
3649                 if (!(hicr & IXGBE_HICR_C))
3650                         break;
3651                 usleep_range(1000, 2000);
3652         }
3653
3654         /* Check command successful completion. */
3655         if ((timeout && i == timeout) ||
3656             !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV))
3657                 return -EIO;
3658
3659         return 0;
3660 }
3661
3662 /**
3663  *  ixgbe_host_interface_command - Issue command to manageability block
3664  *  @hw: pointer to the HW structure
3665  *  @buffer: contains the command to write and where the return status will
3666  *           be placed
3667  *  @length: length of buffer, must be multiple of 4 bytes
3668  *  @timeout: time in ms to wait for command completion
3669  *  @return_data: read and return data from the buffer (true) or not (false)
3670  *  Needed because FW structures are big endian and decoding of
3671  *  these fields can be 8 bit or 16 bit based on command. Decoding
3672  *  is not easily understood without making a table of commands.
3673  *  So we will leave this up to the caller to read back the data
3674  *  in these cases.
3675  *
3676  *  Communicates with the manageability block.  On success return 0
3677  *  else return -EIO or -EINVAL.
3678  **/
3679 int ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
3680                                  u32 length, u32 timeout,
3681                                  bool return_data)
3682 {
3683         u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
3684         struct ixgbe_hic_hdr *hdr = buffer;
3685         u16 buf_len, dword_len;
3686         u32 *u32arr = buffer;
3687         int status;
3688         u32 bi;
3689
3690         if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
3691                 hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
3692                 return -EINVAL;
3693         }
3694         /* Take management host interface semaphore */
3695         status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
3696         if (status)
3697                 return status;
3698
3699         status = ixgbe_hic_unlocked(hw, buffer, length, timeout);
3700         if (status)
3701                 goto rel_out;
3702
3703         if (!return_data)
3704                 goto rel_out;
3705
3706         /* Calculate length in DWORDs */
3707         dword_len = hdr_size >> 2;
3708
3709         /* first pull in the header so we know the buffer length */
3710         for (bi = 0; bi < dword_len; bi++) {
3711                 u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
3712                 le32_to_cpus(&u32arr[bi]);
3713         }
3714
3715         /* If there is any thing in data position pull it in */
3716         buf_len = hdr->buf_len;
3717         if (!buf_len)
3718                 goto rel_out;
3719
3720         if (length < round_up(buf_len, 4) + hdr_size) {
3721                 hw_dbg(hw, "Buffer not large enough for reply message.\n");
3722                 status = -EIO;
3723                 goto rel_out;
3724         }
3725
3726         /* Calculate length in DWORDs, add 3 for odd lengths */
3727         dword_len = (buf_len + 3) >> 2;
3728
3729         /* Pull in the rest of the buffer (bi is where we left off) */
3730         for (; bi <= dword_len; bi++) {
3731                 u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
3732                 le32_to_cpus(&u32arr[bi]);
3733         }
3734
3735 rel_out:
3736         hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
3737
3738         return status;
3739 }
3740
3741 /**
3742  *  ixgbe_set_fw_drv_ver_generic - Sends driver version to firmware
3743  *  @hw: pointer to the HW structure
3744  *  @maj: driver version major number
3745  *  @min: driver version minor number
3746  *  @build: driver version build number
3747  *  @sub: driver version sub build number
3748  *  @len: length of driver_ver string
3749  *  @driver_ver: driver string
3750  *
3751  *  Sends driver version number to firmware through the manageability
3752  *  block.  On success return 0
3753  *  else returns -EBUSY when encountering an error acquiring
3754  *  semaphore or -EIO when command fails.
3755  **/
3756 int ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
3757                                  u8 build, u8 sub, __always_unused u16 len,
3758                                  __always_unused const char *driver_ver)
3759 {
3760         struct ixgbe_hic_drv_info fw_cmd;
3761         int ret_val;
3762         int i;
3763
3764         fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
3765         fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN;
3766         fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED;
3767         fw_cmd.port_num = hw->bus.func;
3768         fw_cmd.ver_maj = maj;
3769         fw_cmd.ver_min = min;
3770         fw_cmd.ver_build = build;
3771         fw_cmd.ver_sub = sub;
3772         fw_cmd.hdr.checksum = 0;
3773         fw_cmd.pad = 0;
3774         fw_cmd.pad2 = 0;
3775         fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd,
3776                                 (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len));
3777
3778         for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
3779                 ret_val = ixgbe_host_interface_command(hw, &fw_cmd,
3780                                                        sizeof(fw_cmd),
3781                                                        IXGBE_HI_COMMAND_TIMEOUT,
3782                                                        true);
3783                 if (ret_val != 0)
3784                         continue;
3785
3786                 if (fw_cmd.hdr.cmd_or_resp.ret_status ==
3787                     FW_CEM_RESP_STATUS_SUCCESS)
3788                         ret_val = 0;
3789                 else
3790                         ret_val = -EIO;
3791
3792                 break;
3793         }
3794
3795         return ret_val;
3796 }
3797
3798 /**
3799  * ixgbe_clear_tx_pending - Clear pending TX work from the PCIe fifo
3800  * @hw: pointer to the hardware structure
3801  *
3802  * The 82599 and x540 MACs can experience issues if TX work is still pending
3803  * when a reset occurs.  This function prevents this by flushing the PCIe
3804  * buffers on the system.
3805  **/
3806 void ixgbe_clear_tx_pending(struct ixgbe_hw *hw)
3807 {
3808         u32 gcr_ext, hlreg0, i, poll;
3809         u16 value;
3810
3811         /*
3812          * If double reset is not requested then all transactions should
3813          * already be clear and as such there is no work to do
3814          */
3815         if (!(hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED))
3816                 return;
3817
3818         /*
3819          * Set loopback enable to prevent any transmits from being sent
3820          * should the link come up.  This assumes that the RXCTRL.RXEN bit
3821          * has already been cleared.
3822          */
3823         hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0);
3824         IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0 | IXGBE_HLREG0_LPBK);
3825
3826         /* wait for a last completion before clearing buffers */
3827         IXGBE_WRITE_FLUSH(hw);
3828         usleep_range(3000, 6000);
3829
3830         /* Before proceeding, make sure that the PCIe block does not have
3831          * transactions pending.
3832          */
3833         poll = ixgbe_pcie_timeout_poll(hw);
3834         for (i = 0; i < poll; i++) {
3835                 usleep_range(100, 200);
3836                 value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS);
3837                 if (ixgbe_removed(hw->hw_addr))
3838                         break;
3839                 if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
3840                         break;
3841         }
3842
3843         /* initiate cleaning flow for buffers in the PCIe transaction layer */
3844         gcr_ext = IXGBE_READ_REG(hw, IXGBE_GCR_EXT);
3845         IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT,
3846                         gcr_ext | IXGBE_GCR_EXT_BUFFERS_CLEAR);
3847
3848         /* Flush all writes and allow 20usec for all transactions to clear */
3849         IXGBE_WRITE_FLUSH(hw);
3850         udelay(20);
3851
3852         /* restore previous register values */
3853         IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr_ext);
3854         IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
3855 }
3856
3857 static const u8 ixgbe_emc_temp_data[4] = {
3858         IXGBE_EMC_INTERNAL_DATA,
3859         IXGBE_EMC_DIODE1_DATA,
3860         IXGBE_EMC_DIODE2_DATA,
3861         IXGBE_EMC_DIODE3_DATA
3862 };
3863 static const u8 ixgbe_emc_therm_limit[4] = {
3864         IXGBE_EMC_INTERNAL_THERM_LIMIT,
3865         IXGBE_EMC_DIODE1_THERM_LIMIT,
3866         IXGBE_EMC_DIODE2_THERM_LIMIT,
3867         IXGBE_EMC_DIODE3_THERM_LIMIT
3868 };
3869
3870 /**
3871  *  ixgbe_get_ets_data - Extracts the ETS bit data
3872  *  @hw: pointer to hardware structure
3873  *  @ets_cfg: extected ETS data
3874  *  @ets_offset: offset of ETS data
3875  *
3876  *  Returns error code.
3877  **/
3878 static int ixgbe_get_ets_data(struct ixgbe_hw *hw, u16 *ets_cfg,
3879                               u16 *ets_offset)
3880 {
3881         int status;
3882
3883         status = hw->eeprom.ops.read(hw, IXGBE_ETS_CFG, ets_offset);
3884         if (status)
3885                 return status;
3886
3887         if ((*ets_offset == 0x0000) || (*ets_offset == 0xFFFF))
3888                 return -EOPNOTSUPP;
3889
3890         status = hw->eeprom.ops.read(hw, *ets_offset, ets_cfg);
3891         if (status)
3892                 return status;
3893
3894         if ((*ets_cfg & IXGBE_ETS_TYPE_MASK) != IXGBE_ETS_TYPE_EMC_SHIFTED)
3895                 return -EOPNOTSUPP;
3896
3897         return 0;
3898 }
3899
3900 /**
3901  *  ixgbe_get_thermal_sensor_data_generic - Gathers thermal sensor data
3902  *  @hw: pointer to hardware structure
3903  *
3904  *  Returns the thermal sensor data structure
3905  **/
3906 int ixgbe_get_thermal_sensor_data_generic(struct ixgbe_hw *hw)
3907 {
3908         u16 ets_offset;
3909         u16 ets_sensor;
3910         u8  num_sensors;
3911         u16 ets_cfg;
3912         int status;
3913         u8  i;
3914         struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
3915
3916         /* Only support thermal sensors attached to physical port 0 */
3917         if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
3918                 return -EOPNOTSUPP;
3919
3920         status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
3921         if (status)
3922                 return status;
3923
3924         num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK);
3925         if (num_sensors > IXGBE_MAX_SENSORS)
3926                 num_sensors = IXGBE_MAX_SENSORS;
3927
3928         for (i = 0; i < num_sensors; i++) {
3929                 u8  sensor_index;
3930                 u8  sensor_location;
3931
3932                 status = hw->eeprom.ops.read(hw, (ets_offset + 1 + i),
3933                                              &ets_sensor);
3934                 if (status)
3935                         return status;
3936
3937                 sensor_index = FIELD_GET(IXGBE_ETS_DATA_INDEX_MASK,
3938                                          ets_sensor);
3939                 sensor_location = FIELD_GET(IXGBE_ETS_DATA_LOC_MASK,
3940                                             ets_sensor);
3941
3942                 if (sensor_location != 0) {
3943                         status = hw->phy.ops.read_i2c_byte(hw,
3944                                         ixgbe_emc_temp_data[sensor_index],
3945                                         IXGBE_I2C_THERMAL_SENSOR_ADDR,
3946                                         &data->sensor[i].temp);
3947                         if (status)
3948                                 return status;
3949                 }
3950         }
3951
3952         return 0;
3953 }
3954
3955 /**
3956  * ixgbe_init_thermal_sensor_thresh_generic - Inits thermal sensor thresholds
3957  * @hw: pointer to hardware structure
3958  *
3959  * Inits the thermal sensor thresholds according to the NVM map
3960  * and save off the threshold and location values into mac.thermal_sensor_data
3961  **/
3962 int ixgbe_init_thermal_sensor_thresh_generic(struct ixgbe_hw *hw)
3963 {
3964         struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
3965         u8  low_thresh_delta;
3966         u8  num_sensors;
3967         u8  therm_limit;
3968         u16 ets_sensor;
3969         u16 ets_offset;
3970         u16 ets_cfg;
3971         int status;
3972         u8  i;
3973
3974         memset(data, 0, sizeof(struct ixgbe_thermal_sensor_data));
3975
3976         /* Only support thermal sensors attached to physical port 0 */
3977         if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
3978                 return -EOPNOTSUPP;
3979
3980         status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
3981         if (status)
3982                 return status;
3983
3984         low_thresh_delta = FIELD_GET(IXGBE_ETS_LTHRES_DELTA_MASK, ets_cfg);
3985         num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK);
3986         if (num_sensors > IXGBE_MAX_SENSORS)
3987                 num_sensors = IXGBE_MAX_SENSORS;
3988
3989         for (i = 0; i < num_sensors; i++) {
3990                 u8  sensor_index;
3991                 u8  sensor_location;
3992
3993                 if (hw->eeprom.ops.read(hw, ets_offset + 1 + i, &ets_sensor)) {
3994                         hw_err(hw, "eeprom read at offset %d failed\n",
3995                                ets_offset + 1 + i);
3996                         continue;
3997                 }
3998                 sensor_index = FIELD_GET(IXGBE_ETS_DATA_INDEX_MASK,
3999                                          ets_sensor);
4000                 sensor_location = FIELD_GET(IXGBE_ETS_DATA_LOC_MASK,
4001                                             ets_sensor);
4002                 therm_limit = ets_sensor & IXGBE_ETS_DATA_HTHRESH_MASK;
4003
4004                 hw->phy.ops.write_i2c_byte(hw,
4005                         ixgbe_emc_therm_limit[sensor_index],
4006                         IXGBE_I2C_THERMAL_SENSOR_ADDR, therm_limit);
4007
4008                 if (sensor_location == 0)
4009                         continue;
4010
4011                 data->sensor[i].location = sensor_location;
4012                 data->sensor[i].caution_thresh = therm_limit;
4013                 data->sensor[i].max_op_thresh = therm_limit - low_thresh_delta;
4014         }
4015
4016         return 0;
4017 }
4018
4019 /**
4020  *  ixgbe_get_orom_version - Return option ROM from EEPROM
4021  *
4022  *  @hw: pointer to hardware structure
4023  *  @nvm_ver: pointer to output structure
4024  *
4025  *  if valid option ROM version, nvm_ver->or_valid set to true
4026  *  else nvm_ver->or_valid is false.
4027  **/
4028 void ixgbe_get_orom_version(struct ixgbe_hw *hw,
4029                             struct ixgbe_nvm_version *nvm_ver)
4030 {
4031         u16 offset, eeprom_cfg_blkh, eeprom_cfg_blkl;
4032
4033         nvm_ver->or_valid = false;
4034         /* Option Rom may or may not be present.  Start with pointer */
4035         hw->eeprom.ops.read(hw, NVM_OROM_OFFSET, &offset);
4036
4037         /* make sure offset is valid */
4038         if (offset == 0x0 || offset == NVM_INVALID_PTR)
4039                 return;
4040
4041         hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_HI, &eeprom_cfg_blkh);
4042         hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_LOW, &eeprom_cfg_blkl);
4043
4044         /* option rom exists and is valid */
4045         if ((eeprom_cfg_blkl | eeprom_cfg_blkh) == 0x0 ||
4046             eeprom_cfg_blkl == NVM_VER_INVALID ||
4047             eeprom_cfg_blkh == NVM_VER_INVALID)
4048                 return;
4049
4050         nvm_ver->or_valid = true;
4051         nvm_ver->or_major = eeprom_cfg_blkl >> NVM_OROM_SHIFT;
4052         nvm_ver->or_build = (eeprom_cfg_blkl << NVM_OROM_SHIFT) |
4053                             (eeprom_cfg_blkh >> NVM_OROM_SHIFT);
4054         nvm_ver->or_patch = eeprom_cfg_blkh & NVM_OROM_PATCH_MASK;
4055 }
4056
4057 /**
4058  *  ixgbe_get_oem_prod_version - Etrack ID from EEPROM
4059  *  @hw: pointer to hardware structure
4060  *  @nvm_ver: pointer to output structure
4061  *
4062  *  if valid OEM product version, nvm_ver->oem_valid set to true
4063  *  else nvm_ver->oem_valid is false.
4064  **/
4065 void ixgbe_get_oem_prod_version(struct ixgbe_hw *hw,
4066                                 struct ixgbe_nvm_version *nvm_ver)
4067 {
4068         u16 rel_num, prod_ver, mod_len, cap, offset;
4069
4070         nvm_ver->oem_valid = false;
4071         hw->eeprom.ops.read(hw, NVM_OEM_PROD_VER_PTR, &offset);
4072
4073         /* Return is offset to OEM Product Version block is invalid */
4074         if (offset == 0x0 || offset == NVM_INVALID_PTR)
4075                 return;
4076
4077         /* Read product version block */
4078         hw->eeprom.ops.read(hw, offset, &mod_len);
4079         hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_CAP_OFF, &cap);
4080
4081         /* Return if OEM product version block is invalid */
4082         if (mod_len != NVM_OEM_PROD_VER_MOD_LEN ||
4083             (cap & NVM_OEM_PROD_VER_CAP_MASK) != 0x0)
4084                 return;
4085
4086         hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_L, &prod_ver);
4087         hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_H, &rel_num);
4088
4089         /* Return if version is invalid */
4090         if ((rel_num | prod_ver) == 0x0 ||
4091             rel_num == NVM_VER_INVALID || prod_ver == NVM_VER_INVALID)
4092                 return;
4093
4094         nvm_ver->oem_major = prod_ver >> NVM_VER_SHIFT;
4095         nvm_ver->oem_minor = prod_ver & NVM_VER_MASK;
4096         nvm_ver->oem_release = rel_num;
4097         nvm_ver->oem_valid = true;
4098 }
4099
4100 /**
4101  *  ixgbe_get_etk_id - Return Etrack ID from EEPROM
4102  *
4103  *  @hw: pointer to hardware structure
4104  *  @nvm_ver: pointer to output structure
4105  *
4106  *  word read errors will return 0xFFFF
4107  **/
4108 void ixgbe_get_etk_id(struct ixgbe_hw *hw,
4109                       struct ixgbe_nvm_version *nvm_ver)
4110 {
4111         u16 etk_id_l, etk_id_h;
4112
4113         if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_LOW, &etk_id_l))
4114                 etk_id_l = NVM_VER_INVALID;
4115         if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_HI, &etk_id_h))
4116                 etk_id_h = NVM_VER_INVALID;
4117
4118         /* The word order for the version format is determined by high order
4119          * word bit 15.
4120          */
4121         if ((etk_id_h & NVM_ETK_VALID) == 0) {
4122                 nvm_ver->etk_id = etk_id_h;
4123                 nvm_ver->etk_id |= (etk_id_l << NVM_ETK_SHIFT);
4124         } else {
4125                 nvm_ver->etk_id = etk_id_l;
4126                 nvm_ver->etk_id |= (etk_id_h << NVM_ETK_SHIFT);
4127         }
4128 }
4129
4130 void ixgbe_disable_rx_generic(struct ixgbe_hw *hw)
4131 {
4132         u32 rxctrl;
4133
4134         rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
4135         if (rxctrl & IXGBE_RXCTRL_RXEN) {
4136                 if (hw->mac.type != ixgbe_mac_82598EB) {
4137                         u32 pfdtxgswc;
4138
4139                         pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
4140                         if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) {
4141                                 pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN;
4142                                 IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
4143                                 hw->mac.set_lben = true;
4144                         } else {
4145                                 hw->mac.set_lben = false;
4146                         }
4147                 }
4148                 rxctrl &= ~IXGBE_RXCTRL_RXEN;
4149                 IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl);
4150         }
4151 }
4152
4153 void ixgbe_enable_rx_generic(struct ixgbe_hw *hw)
4154 {
4155         u32 rxctrl;
4156
4157         rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
4158         IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, (rxctrl | IXGBE_RXCTRL_RXEN));
4159
4160         if (hw->mac.type != ixgbe_mac_82598EB) {
4161                 if (hw->mac.set_lben) {
4162                         u32 pfdtxgswc;
4163
4164                         pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
4165                         pfdtxgswc |= IXGBE_PFDTXGSWC_VT_LBEN;
4166                         IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
4167                         hw->mac.set_lben = false;
4168                 }
4169         }
4170 }
4171
4172 /** ixgbe_mng_present - returns true when management capability is present
4173  * @hw: pointer to hardware structure
4174  **/
4175 bool ixgbe_mng_present(struct ixgbe_hw *hw)
4176 {
4177         u32 fwsm;
4178
4179         if (hw->mac.type < ixgbe_mac_82599EB)
4180                 return false;
4181
4182         fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM(hw));
4183
4184         return !!(fwsm & IXGBE_FWSM_FW_MODE_PT);
4185 }
4186
4187 /**
4188  *  ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
4189  *  @hw: pointer to hardware structure
4190  *  @speed: new link speed
4191  *  @autoneg_wait_to_complete: true when waiting for completion is needed
4192  *
4193  *  Set the link speed in the MAC and/or PHY register and restarts link.
4194  */
4195 int ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
4196                                           ixgbe_link_speed speed,
4197                                           bool autoneg_wait_to_complete)
4198 {
4199         ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
4200         ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
4201         bool autoneg, link_up = false;
4202         u32 speedcnt = 0;
4203         int status = 0;
4204         u32 i = 0;
4205
4206         /* Mask off requested but non-supported speeds */
4207         status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg);
4208         if (status)
4209                 return status;
4210
4211         speed &= link_speed;
4212
4213         /* Try each speed one by one, highest priority first.  We do this in
4214          * software because 10Gb fiber doesn't support speed autonegotiation.
4215          */
4216         if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
4217                 speedcnt++;
4218                 highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
4219
4220                 /* Set the module link speed */
4221                 switch (hw->phy.media_type) {
4222                 case ixgbe_media_type_fiber:
4223                         hw->mac.ops.set_rate_select_speed(hw,
4224                                                     IXGBE_LINK_SPEED_10GB_FULL);
4225                         break;
4226                 case ixgbe_media_type_fiber_qsfp:
4227                         /* QSFP module automatically detects MAC link speed */
4228                         break;
4229                 default:
4230                         hw_dbg(hw, "Unexpected media type\n");
4231                         break;
4232                 }
4233
4234                 /* Allow module to change analog characteristics (1G->10G) */
4235                 msleep(40);
4236
4237                 status = hw->mac.ops.setup_mac_link(hw,
4238                                                     IXGBE_LINK_SPEED_10GB_FULL,
4239                                                     autoneg_wait_to_complete);
4240                 if (status)
4241                         return status;
4242
4243                 /* Flap the Tx laser if it has not already been done */
4244                 if (hw->mac.ops.flap_tx_laser)
4245                         hw->mac.ops.flap_tx_laser(hw);
4246
4247                 /* Wait for the controller to acquire link.  Per IEEE 802.3ap,
4248                  * Section 73.10.2, we may have to wait up to 500ms if KR is
4249                  * attempted.  82599 uses the same timing for 10g SFI.
4250                  */
4251                 for (i = 0; i < 5; i++) {
4252                         /* Wait for the link partner to also set speed */
4253                         msleep(100);
4254
4255                         /* If we have link, just jump out */
4256                         status = hw->mac.ops.check_link(hw, &link_speed,
4257                                                         &link_up, false);
4258                         if (status)
4259                                 return status;
4260
4261                         if (link_up)
4262                                 goto out;
4263                 }
4264         }
4265
4266         if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
4267                 speedcnt++;
4268                 if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
4269                         highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
4270
4271                 /* Set the module link speed */
4272                 switch (hw->phy.media_type) {
4273                 case ixgbe_media_type_fiber:
4274                         hw->mac.ops.set_rate_select_speed(hw,
4275                                                      IXGBE_LINK_SPEED_1GB_FULL);
4276                         break;
4277                 case ixgbe_media_type_fiber_qsfp:
4278                         /* QSFP module automatically detects link speed */
4279                         break;
4280                 default:
4281                         hw_dbg(hw, "Unexpected media type\n");
4282                         break;
4283                 }
4284
4285                 /* Allow module to change analog characteristics (10G->1G) */
4286                 msleep(40);
4287
4288                 status = hw->mac.ops.setup_mac_link(hw,
4289                                                     IXGBE_LINK_SPEED_1GB_FULL,
4290                                                     autoneg_wait_to_complete);
4291                 if (status)
4292                         return status;
4293
4294                 /* Flap the Tx laser if it has not already been done */
4295                 if (hw->mac.ops.flap_tx_laser)
4296                         hw->mac.ops.flap_tx_laser(hw);
4297
4298                 /* Wait for the link partner to also set speed */
4299                 msleep(100);
4300
4301                 /* If we have link, just jump out */
4302                 status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
4303                                                 false);
4304                 if (status)
4305                         return status;
4306
4307                 if (link_up)
4308                         goto out;
4309         }
4310
4311         /* We didn't get link.  Configure back to the highest speed we tried,
4312          * (if there was more than one).  We call ourselves back with just the
4313          * single highest speed that the user requested.
4314          */
4315         if (speedcnt > 1)
4316                 status = ixgbe_setup_mac_link_multispeed_fiber(hw,
4317                                                       highest_link_speed,
4318                                                       autoneg_wait_to_complete);
4319
4320 out:
4321         /* Set autoneg_advertised value based on input link speed */
4322         hw->phy.autoneg_advertised = 0;
4323
4324         if (speed & IXGBE_LINK_SPEED_10GB_FULL)
4325                 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
4326
4327         if (speed & IXGBE_LINK_SPEED_1GB_FULL)
4328                 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
4329
4330         return status;
4331 }
4332
4333 /**
4334  *  ixgbe_set_soft_rate_select_speed - Set module link speed
4335  *  @hw: pointer to hardware structure
4336  *  @speed: link speed to set
4337  *
4338  *  Set module link speed via the soft rate select.
4339  */
4340 void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw,
4341                                       ixgbe_link_speed speed)
4342 {
4343         u8 rs, eeprom_data;
4344         int status;
4345
4346         switch (speed) {
4347         case IXGBE_LINK_SPEED_10GB_FULL:
4348                 /* one bit mask same as setting on */
4349                 rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
4350                 break;
4351         case IXGBE_LINK_SPEED_1GB_FULL:
4352                 rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
4353                 break;
4354         default:
4355                 hw_dbg(hw, "Invalid fixed module speed\n");
4356                 return;
4357         }
4358
4359         /* Set RS0 */
4360         status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
4361                                            IXGBE_I2C_EEPROM_DEV_ADDR2,
4362                                            &eeprom_data);
4363         if (status) {
4364                 hw_dbg(hw, "Failed to read Rx Rate Select RS0\n");
4365                 return;
4366         }
4367
4368         eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
4369
4370         status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
4371                                             IXGBE_I2C_EEPROM_DEV_ADDR2,
4372                                             eeprom_data);
4373         if (status) {
4374                 hw_dbg(hw, "Failed to write Rx Rate Select RS0\n");
4375                 return;
4376         }
4377
4378         /* Set RS1 */
4379         status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
4380                                            IXGBE_I2C_EEPROM_DEV_ADDR2,
4381                                            &eeprom_data);
4382         if (status) {
4383                 hw_dbg(hw, "Failed to read Rx Rate Select RS1\n");
4384                 return;
4385         }
4386
4387         eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
4388
4389         status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
4390                                             IXGBE_I2C_EEPROM_DEV_ADDR2,
4391                                             eeprom_data);
4392         if (status) {
4393                 hw_dbg(hw, "Failed to write Rx Rate Select RS1\n");
4394                 return;
4395         }
4396 }
This page took 0.277634 seconds and 4 git commands to generate.