board: apalis_imx6: check for and report ecc errors in fuses
The PMIC on Apalis iMX6 may have ECC errors in fuses that will prevent
correct settings. Up to one bit error per fuse bank may be reported and
corrected by the ECC logic. Two bit errors can only be reported.
Stefan Agner [Fri, 8 Feb 2019 17:12:24 +0000 (18:12 +0100)]
apalis_imx6: use SDP if USB serial downloader has been used
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
We have two commands to change the bootmode fuses:
mfgr_fuse which set fuse 0/5 and 0/6
and
updt_fuse which burns bit 4 of 0/5.
Before BSP 2.6 we fused in mfgr_fuse 0x5062, which boots
from the user partition of the eMMC.
To workaround certain hangs we moved to fastboot mode and
using the first bootpartition of the eMMC requiring a fuse
value of 0x5072 which could be achieved by the then added
updt_fuse command. At the same time the mfgr_fuse command
was changed to also fuse 0x5072, revert that second change
so that one can fuse both values, one with just mfgr_fuse
and the later with mfgr_fuse;updt_fuse.
Note that the mfgr_fuse command is only needed at module
production time, a customer might need to use updt_fuse
when upgrading an older module to be compatible with a
newer image. The command is integrated into the image
update scripts.
Marcel Ziswiler [Fri, 8 Feb 2019 17:12:17 +0000 (18:12 +0100)]
apalis_imx6: add distroboot support
Add support for distro boot. This is especially helpful for external
devices. There is a global boot command which scans a predefined
list of boot targets:
run distro_bootcmd
As well as direct boot commands such as:
run bootcmd_mmc1
run bootcmd_mmc2
run bootcmd_usb
run bootcmd_dhcp
...
Refer to doc/README.distro for details.
While at it, remove the CONFIG_DRIVE_TYPES define which has not
been used and was meant to be used for multi device boot support
which is now provided by distroboot.
Marcel Ziswiler [Fri, 8 Feb 2019 17:12:10 +0000 (18:12 +0100)]
apalis_imx6: clean-up and migrate gpios to using driver model
Migrate GPIOs to using driver model, properly request backlight,
Ethernet PHY reset, MMC/SD card detect and USB power GPIOs and also
enable SION bit in pin muxing for Apalis, backlight, eMMC reset,
Ethernet PHY reset and USB power enable GPIOs.
While at it also update copyright year, clean-up/re-order includes,
add some comments clarifying ifdef scope and do some White-space
clean-up.
Lukasz Majewski [Wed, 13 Feb 2019 21:46:48 +0000 (22:46 +0100)]
ARM: DTS: Update pcm052 based dts files (bk4r1/pcm052)
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts
file with more on SoC HW description.
The pcm052.dts has been renamed to vf610-pcm052.dts as well.
Moreover, a new vf610-pcm052.drsi file has been introduced
to reuse the common code between devices based on Phytec's
pcm052 modules.
Ported from Linux kernel - v4.20 (tag)
Lukasz Majewski [Wed, 13 Feb 2019 21:46:41 +0000 (22:46 +0100)]
vybrid: clock: Provide enable_i2c_clk() function for Vybrid
Provide function to enable I2C clocks for vf610 - in the generic code.
This function overrides the default weak function implementation (which
only returns 1).
Tom Rini [Sat, 13 Apr 2019 12:27:26 +0000 (08:27 -0400)]
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
Change FDT memory type from runtime data to boot services data
Following Ard's suggestion:
Runtime data sections are intended for data that is used by the runtime
services implementation.
Let's change the type to EFI_BOOT_SERVICES_DATA.
This also fixes booting of armv7 using efi and fdtcontroladdr.
efi_loader: update virtual address in efi_mem_carve_out
Handle virtual address in efi_mem_carve_out() function
when a new region is created to avoid issue in EFI memory map.
Signed-off-by: Patrick Delaunay <[email protected]>
At boottime physical and virtual addressed have to be the same.
This allowed to simplify the proposed logic.
Patrick Delaunay [Wed, 10 Apr 2019 09:02:58 +0000 (11:02 +0200)]
efi_loader: add protection for block_dev
Check the value of block_dev before to use this pointer.
This patch solves problem for the command "load" when ubifs
is previously mounted: in this case the function
blk_get_device_part_str("ubi 0") don't return error but return
block_dev = NULL and then data abort.
The UEFI variables PlatformLang and PlatformLangCodes specify the current
firmware language and the list of all available languages.
Currently their values are hard coded. With the patch a new configuration
variable EFI_PLATFORM_LANG_CODES is provided.
When initializing the UEFI subsystem this configuration variable is used to
initialize PlatformLangCodes. The value of variable PlatformLang is read.
If it is not set, the first language specified in EFI_PLATFORM_LANG_CODES
is used to initialize PlatformLang.
efi_loader: the development target should be the EBBR
Two subsets of the UEFI specifications have been defined. The one for
servers is "Server Base Boot Requirements System Software on ARM
Platforms" (SBBR), the one for embedded systems is the "Embedded Base Boot
Requirements (EBBR) Specification". Reaching compliance with thei EBBR is a
more realistic development target than reaching complicance with the SBBR.
Patrick Wildt [Tue, 9 Apr 2019 20:58:30 +0000 (22:58 +0200)]
efi: fix memory calculation overflow on 32-bit systems
There are Cubox-i machines out there with nearly 4 GiB of RAM. The
RAM starts at 0x10000000 with a size of 0xf0000000. Thus the end
of RAM is at 0x100000000. This overflows a 32-bit integer, which
should be fine since in the EFI memory code the variables used are
all 64-bit with a fixed size. Unfortunately EFI_PAGE_MASK, which is
used in the EFI memory code to remove the lower bits, is based on
the EFI_PAGE_SIZE macro which, uses 1UL with a shift. This means
the resulting mask is UL, which is only 32-bit on ARMv7. Use ULL to
make sure that even on 32-bit platforms we use a 64-bit long mask.
Without this there will be no memory available in the EFI memory map
and bootefi will fail allocating pages.
The first functions of the UEFI sub-system are invoked before reaching the
U-Boot shell, e.g. efi_set_bootdev(), efi_dp_from_name(),
efi_dp_from_file(). We should be able to print out device paths for
debugging purposes here.
When printing device paths via printf("%pD\n", dp) this invokes functions
defined as EFIAPI. So efi_save_gd() must be called beforehand.
So let's move the efi_save_gd() call to function initr_reloc_global_data(()
in board_r.c.
Tom Rini [Fri, 12 Apr 2019 16:34:44 +0000 (12:34 -0400)]
Merge git://git.denx.de/u-boot-marvell
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
Tom Rini [Fri, 12 Apr 2019 16:22:43 +0000 (12:22 -0400)]
Merge branch '2019-04-11-ti-master-imports'
- Improve Keystone 3 SoC support (DMA, TI SCI)
- Improve Keystone 2 SoC support (PHY fixes on various platforms)
- Improve am335x families (new platforms, more boot mode options in SPL
via DM).
- General DaVinci, OMAP5 fixes.
Stefan Roese [Fri, 5 Apr 2019 11:44:43 +0000 (13:44 +0200)]
phy: Add USB PHY driver for the MT76x8 (7628/7688) SoC
This driver is derived from this Linux driver:
linux/drivers/phy/ralink/phy-ralink-usb.c
The driver sets up power and host mode, but also needs to configure PHY
registers for the MT7628 and MT7688.
I removed the reset controller handling for the USB host and device, as
it does not seem to be necessary right now. The soft reset bits for both
devices are enabled by default and testing has shown (with hackish
reset handling added), that USB related commands work identical with
or without the reset handling.
Please note that the resulting USB support is tested only very minimal.
I was able to detect one of my 3 currently available USB sticks.
Perhaps some further work is needed to fully support the EHCI controller
integrated in the MT76x8 SoC.
- reading the environment it is slow, therefore having a smaller env
improves the speed.
- usually in the environment there are only few variables, therefore
the enviromnent is almost empty.
- because the same image can run on different boards which may have
different flashes with different page sizes, the CONFIG_ENV_SECT_SIZE
can't be change, it is set to least common multiple of the page sizes.
Adding this change improves the boot time. Before update for reading the
entire environment it took ~850 msec, after the change it takes ~40 msecs.
In Jaguar2 SoC family there are 3 different pcb. Each of this needs
to configure the phys in different ways. Therefore implement the
function board_phy_config and based on pcb configure them accordingly.
projects / u-boot.git / log