Jernej Skrabec [Mon, 11 Jan 2021 20:11:46 +0000 (21:11 +0100)]
sunxi: Add support for H616 SoC
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Andre Przywara [Mon, 11 Jan 2021 20:11:44 +0000 (21:11 +0100)]
mmc: sunxi: Refactor mod clock register offset
So far the only difference between the various Allwinner MMC controller
we are concerned about is the mod clock register offset.
This is actually not directly related to the MMC controller IP, but an
integration choice, dependent on the SoC this appears in.
To avoid becoming trapped with some compatible fallback strings, let's
remove the whole struct sunxi_mmc_variant, and replace this with a SoC
based choice, which we can derive from the CONFIG_MACH_SUNx_y symbols.
Jernej Skrabec [Mon, 11 Jan 2021 20:11:43 +0000 (21:11 +0100)]
sunxi: Add H616 DRAM support
Allwinner H616 supports many types of DRAM. Most notably it supports
LPDDR4. However, all commercially available boards at this time use
only DDR3, so this commit adds only DDR3 support.
Controller and MBUS are very similar to H6 but PHY is completely
unknown.
Andre Przywara [Mon, 11 Jan 2021 20:11:39 +0000 (21:11 +0100)]
sunxi: support loading with SPL > 32KB
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.
spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.
In the process of function rework, also add missing function argument.
Jernej Skrabec [Mon, 11 Jan 2021 20:11:36 +0000 (21:11 +0100)]
i2c: mvtwsi: sunxi: update macro
While currently none of the newer Allwinner SoCs currently has I2C
support implemented in U-Boot, this will change soon. mvtwsi driver is
good as it is for them except one macro. Update it to be ready once I2C
support lands for those SoCs.
Jernej Skrabec [Mon, 11 Jan 2021 20:11:34 +0000 (21:11 +0100)]
sunxi: Introduce common symbol for H6 like SoCs
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Andre Przywara [Mon, 18 Jan 2021 23:23:59 +0000 (23:23 +0000)]
sunxi: Properly check for SATAPWR and MACPWR
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!
Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.
Jernej Skrabec [Wed, 6 Jan 2021 17:02:57 +0000 (18:02 +0100)]
sunxi: Add support for Tanix TX6
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
Andre Przywara [Sat, 14 Nov 2020 17:37:46 +0000 (17:37 +0000)]
net: sun8i-emac: Allow all RGMII PHY modes
So far all GBit users of the sun8i-emac driver were using the "rgmii"
PHY mode, even though this turns out to be wrong. It just worked because
the PHY driver doesn't do the proper setup (yet).
In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the
correct ones.
To allow the DTs to describe the phy-mode correctly, and to stay
compatible with Linux, at least allow those other RGMII modes in the
driver.
This avoids breakage if mainline DTs will be synced with U-Boot.
Tom Rini [Mon, 25 Jan 2021 14:02:06 +0000 (09:02 -0500)]
Merge tag 'doc-2021-04-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for documentation tag doc-2021-04-rc1 (2)
* Man-pages for sbi, exit, for, echo, loady, true, false, conitrace
* Adjust suppression of newline in echo command.
* Provide unit test for echo command.
Tom Rini [Mon, 25 Jan 2021 14:01:28 +0000 (09:01 -0500)]
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
By default the echo command emits its arguments followed by a line feed.
If any of the arguments contains the sub-string "\c", the line feed is
suppressed.
This does not match shells used in Linux and BSD where the first argument
has to be -n to suppress the line feed.
The hush shell interferes with the parsing of backslashes. E.g. in the
following command line quadruple backslashes are required for suppressing
the line feed:
for i in 1 2 3; do for j in 4 5; do echo \\\\c ${i}${j}; done; echo; done;
To avoid unexpected behavior the patch changes echo to use -n as first
argument to suppress the line feed.
Unfortunately we now see a number of now-fatal warnings about duplicate
labels. It is often unclear how best to re-write the document in
question to not duplicate these otherwise logical headings.
Marc Ferland [Mon, 4 Jan 2021 19:07:53 +0000 (14:07 -0500)]
arm: dart6ul: fix ddr size macro
The previous macro was off by one bit and so we were getting a ddr
size which was twice the real size. This commit refactors the macro so
it returns the right size in _bytes_ and modifies the printf call so the
size is still printed in MiB.
Marek Vasut [Mon, 18 Jan 2021 23:58:32 +0000 (00:58 +0100)]
spi: imx: Define register bits in the driver
The CSPI/ECSPI register bits do not differ between newer SoCs, instead
of having multiple copies of the same thing for each iMX SoC, define
the bits in the driver.
Marek Vasut [Mon, 18 Jan 2021 23:58:31 +0000 (00:58 +0100)]
clk: imx: Add ECSPI to iMX8MN
Add ECSPI clock entries to iMX8MN clock driver. Only make those entries
available in case SPI support in U-Boot is enabled at all to conserve
space, esp. in SPL.
Adam Ford [Mon, 18 Jan 2021 21:43:09 +0000 (15:43 -0600)]
arm64: dts: imx8mm-beacon: Resync imx8mm-beacon-som with 5.11-rc4
In order to support the QSPI chip on the SOM, the Flexspi bus
needs to be configured to talk with the SPI chip.
Resync the som device tree with 5.11-rc4
Martin Fuzzey [Wed, 13 Jan 2021 10:21:03 +0000 (11:21 +0100)]
w1: mxc: fix build
Now that header files no longer include common.h it must be included
first.
Otherwise the build fails with errors like
include/asm/arch/clock.h:43:1: error: unknown type name 'u32'
u32 imx_get_uartclk(void);
Fixes: c3dc39a2f85b ("arm: Don't include common.h in header files") Signed-off-by: Martin Fuzzey <[email protected]> Reviewed-by: Simon Glass <[email protected]>
Marc Ferland [Mon, 4 Jan 2021 15:41:57 +0000 (10:41 -0500)]
arm: dart6ul: enable DM_ETH for the dart6ul
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:
* moves the fec2 node and pin definition to the carrier board DTS
since the phy associated with it is on the carrier board and not on
the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
are easier to reference;
* add clock properties to the phy nodes since they are connected to the
50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.
Sean Anderson [Mon, 28 Dec 2020 19:58:30 +0000 (14:58 -0500)]
mx6ul(l)evk: Enable DM_ETH_PHY
This fixes eth0 not initializing properly. Both eth0 and eth1 use the
MDIO interface on eth1 to access their PHYs. However, without
DM_ETH_PHY, eth0 still tries to use its own MDIO interface to access its
phy. Before this patch, a boot log might contain lines like
Net:
Warning: ethernet@20b4000 using MAC address from ROM
eth1: ethernet@20b4000 [PRIME]Could not get PHY for FEC0: addr 2
After this patch they now look like
Net:
Warning: ethernet@20b4000 using MAC address from ROM
eth1: ethernet@20b4000 [PRIME]Get shared mii bus on ethernet@2188000
Warning: ethernet@2188000 using MAC address from ROM
, eth0: ethernet@2188000
As an alternative to DM_ETH_PHY, FEC_MXC_SHARE_MDIO could also have been
used to achieve the same effect.
Alice Guo [Fri, 18 Dec 2020 07:19:27 +0000 (15:19 +0800)]
board: imx8mp: add boot.cmd for distro boot on iMX8MP
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value
"/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
Alice Guo [Fri, 18 Dec 2020 07:19:26 +0000 (15:19 +0800)]
imx8mp: configs: add support for distro boot commands
Supported boot device types in iMX8MP: MMC.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is
for command fstype.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution. kernel_addr_r is the location in RAM where
the kernel will be loaded to. Delete unnecessary environment variables
because "run distro_bootcmd" is set to be the default boot mode.
On the iMX8MP platform I used, "mmc1" represents SD card and "mmc2"
represents eMMC.
Alice Guo [Fri, 18 Dec 2020 06:50:08 +0000 (14:50 +0800)]
board: imx8mm: add boot.cmd for distro boot on iMX8MM
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value "
/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
Peng Fan [Thu, 17 May 2018 07:15:59 +0000 (15:15 +0800)]
imx8m: add QSPI boot dev
When boot type could not be detected from rom sw info,
read sbmr1 to detect, here we only use it to detect FLEXSPI
boot, because ROM not update it in rom sw info.
Ye Li [Mon, 3 Aug 2020 05:43:45 +0000 (22:43 -0700)]
imx: nandbcb: Fix resource leak in read_fcb
Fix Coverity Issue 9006657. In read_fcb, leak of memory to system
resource "fcb_raw_page". Adjust the sequence to check the mtd bad
block prior than allocation of "fcb_raw_page", also check the NULL
return of allocation.
Ye Li [Mon, 3 Aug 2020 04:11:06 +0000 (21:11 -0700)]
imx: nandbcb: Fix resource leak
Fix Coverity Issue 9006655. In write_fcb, leak of memory to resource
"fcb_raw_page". Since we have initialized the "ret" to 0, should return
the value of ret.
Ye Li [Wed, 30 Sep 2020 04:55:32 +0000 (21:55 -0700)]
imx: ddr: imx8m: Move selfref_en after DDR scrub
When doing DDR scrub, the DDR may enter into self refresh if the
selfref_en is enabled before DDR scrub. This will cause scrub
can't complete that SBRSTAT.scrub_done won't be set.
Since the selfref_en can be programmed during the course of
normal operation, move it after DDR scrub
Sughosh Ganu [Fri, 22 Jan 2021 15:04:56 +0000 (20:34 +0530)]
mkeficapsule: Miscellaneous fixes in the utility
Miscellaneous fixes in the mkeficapsule utility -- these include a few
resource leak issues flagged by Coverity along with some additional
code improvements suggested by Heinrich during code review.
AKASHI Takahiro [Fri, 22 Jan 2021 01:43:27 +0000 (10:43 +0900)]
efi_loader: capsule: fix SIZEOF_MISMATCH warning
CID 316361 says:
> Passing argument "count * 8UL /* sizeof (*files) */" to
> function "dlmalloc" and then casting the return value to "u16 **" is
> suspicious. In this particular case "sizeof (u16 **)" happens to be equal
> to "sizeof (u16 *)", but this is not a portable assumption.
> > 767 tmp_files = malloc(count * sizeof(*files));
The change in this patch fixes the ambiguity.
Signed-off-by: AKASHI Takahiro <[email protected]> Fixes: CID 316361
For readability use *tmp_files instead of tmp_files[0] Reviewed-by: Heinrich Schuchardt <[email protected]> Signed-off-by: Heinrich Schuchardt <[email protected]>
AKASHI Takahiro [Fri, 22 Jan 2021 01:42:48 +0000 (10:42 +0900)]
cmd: efidebug: always check return code from get_variable()
CID 316364 says:
> Null pointer dereferences (FORWARD_NULL)
> printf("Result total size: 0x%x\n", result->variable_total_size);
at do_efi_capsule_res().
The code is basically safe because a buffer for "result" is allocated
by malloc() and filled up by the second get_variable(), which fails any way
if the allocation has failed.
But the first (and second) get_variable() possibly returns an error other
than EFI_SUCCESS. We always need to check the return code from
get_variable() before accessing the data in "result".
While this change won't suppress CID 316364, the resulting code is much
safer.
The short name and extension of FAT files are stored in adjacent fields of
the directory entry. For some operations like calculating a checksum or
copying both fields it is preferable to treat both as one structure.
Change the definition of the directory entry structure to include a
structure comprising the name and the extension field.
This resolves Coverity CID 316357, CID 316350, CID 316348.
fs: fat: consistent error handling for flush_dir()
Provide function description for flush_dir().
Move all error messages for flush_dir() from the callers to the function.
Move mapping of errors to -EIO to the function.
Always check return value of flush_dir() (Coverity CID 316362).
In fat_unlink() return -EIO if flush_dirty_fat_buffer() fails.
Martin Hundebøll [Mon, 30 Nov 2020 11:11:32 +0000 (12:11 +0100)]
tools: env: return error if ubi_update_start() fails
The UBI_IOCVOLUP ioctl can fail if exclusive access to the volume isn't
obtained. If this happens, the flush operation doesn't return error,
leaving the caller without knowledge of missing flush.
Fix this by forwarding the error (-1) from ubi_update_start().
Fixes: 34255b92e6e ("tools: env: Add support for direct read/write UBI volumes") Signed-off-by: Martin Hundebøll <[email protected]>
Joel Stanley [Tue, 8 Dec 2020 04:12:14 +0000 (14:42 +1030)]
image-fit: Fix FIT_CIPHER linking
When CONFIG_FIT_CIPHER=y and CONFIG_FIT_SIGNATURE=n is there is no
implementation of image_get_host_blob for mkimage/dumpimage:
/usr/bin/ld: tools/common/image-cipher.o: in function `fit_image_decrypt_data':
image-cipher.c:(.text+0x9a): undefined reference to `image_get_host_blob'
Move the implementation to a common file so it can be shaed between
image-cipher.c and image-fit-sig.c.
Joel Stanley [Tue, 8 Dec 2020 04:12:13 +0000 (14:42 +1030)]
tools/Makefile: FIT_CIPHER requires libssl
If CONFIG_FIT_CIPHER is enabled without CONFIG_FIT_SIGNATURE then
mkimage/dumpimage will fail to link:
/usr/bin/ld: tools/common/image-cipher.o: in function `fit_image_decrypt_data':
image-cipher.c:(.text+0x9a): undefined reference to `image_get_host_blob'
/usr/bin/ld: tools/common/image-cipher.o:(.data.rel+0x10): undefined reference to `EVP_aes_128_cbc'
/usr/bin/ld: tools/common/image-cipher.o:(.data.rel+0x40): undefined reference to `EVP_aes_192_cbc'
/usr/bin/ld: tools/common/image-cipher.o:(.data.rel+0x70): undefined reference to `EVP_aes_256_cbc'
/usr/bin/ld: tools/lib/aes/aes-encrypt.o: in function `image_aes_encrypt':
aes-encrypt.c:(.text+0x22): undefined reference to `EVP_CIPHER_CTX_new'
/usr/bin/ld: aes-encrypt.c:(.text+0x6f): undefined reference to `EVP_EncryptInit_ex'
/usr/bin/ld: aes-encrypt.c:(.text+0x8d): undefined reference to `EVP_EncryptUpdate'
/usr/bin/ld: aes-encrypt.c:(.text+0xac): undefined reference to `EVP_CIPHER_CTX_free'
/usr/bin/ld: aes-encrypt.c:(.text+0xf2): undefined reference to `EVP_EncryptFinal_ex'
collect2: error: ld returned 1 exit status
Philippe Reynes [Tue, 24 Nov 2020 13:39:48 +0000 (14:39 +0100)]
tools: image-host: add support for several sub-images
The propoerty sign-images points to images in the configuration
node. But thoses images may references severals "sub-images" (for
example for images loadable). This commit adds the support of
severals sub-images.