X-Git-Url: https://repo.jachan.dev/u-boot.git/blobdiff_plain/ffb96d55d13759a7e4fe4ba5fc5e3eb6fac11738..8d3a25685e4aac7070365a2b3c53c2c81b27930f:/include/configs/work_92105.h

diff --git a/include/configs/work_92105.h b/include/configs/work_92105.h
index dc8e99fffd..56f53b9732 100644
--- a/include/configs/work_92105.h
+++ b/include/configs/work_92105.h
@@ -18,15 +18,13 @@
  * Define work_92105 machine type by hand -- done only for compatibility
  * with original board code
  */
-#define MACH_TYPE_WORK_92105		736
-#define CONFIG_MACH_TYPE		MACH_TYPE_WORK_92105
+#define CONFIG_MACH_TYPE		736
 
 #define CONFIG_SYS_ICACHE_OFF
 #define CONFIG_SYS_DCACHE_OFF
 #if !defined(CONFIG_SPL_BUILD)
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #endif
-#define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_EARLY_INIT_R
 
 /* generate LPC32XX-specific SPL image */
@@ -52,7 +50,6 @@
  * Serial Driver
  */
 #define CONFIG_SYS_LPC32XX_UART		5   /* UART5 - NS16550 */
-#define CONFIG_BAUDRATE			115200
 
 /*
  * Ethernet Driver
@@ -63,9 +60,6 @@
 #define CONFIG_PHYLIB
 #define CONFIG_PHY_ADDR 0
 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
 /* FIXME: remove "Waiting for PHY auto negotiation to complete..." message */
 
 /*
@@ -74,14 +68,12 @@
 
 #define CONFIG_SYS_I2C_LPC32XX
 #define CONFIG_SYS_I2C
-#define CONFIG_CMD_I2C
 #define CONFIG_SYS_I2C_SPEED 350000
 
 /*
  * I2C EEPROM
  */
 
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x56
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
 
@@ -89,21 +81,11 @@
  * I2C RTC
  */
 
-#define CONFIG_CMD_DATE
 #define CONFIG_RTC_DS1374
 
-/*
- * I2C Temperature Sensor (DTT)
- */
-
-#define CONFIG_CMD_DTT
-#define CONFIG_DTT_SENSORS { 0, 1 }
-#define CONFIG_DTT_DS620
-
 /*
  * U-Boot General Configurations
  */
-#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_CBSIZE		1024
 #define CONFIG_SYS_PBSIZE		\
@@ -111,19 +93,8 @@
 #define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 
-#define CONFIG_SYS_HUSH_PARSER
-
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DOS_PARTITION
-
-/*
- * No NOR
- */
-
-#define CONFIG_SYS_NO_FLASH
 
 /*
  * NAND chip timings for FIXME: which one?
@@ -154,18 +125,15 @@
  * GPIO
  */
 
-#define CONFIG_CMD_GPIO
 #define CONFIG_LPC32XX_GPIO
 
 /*
  * SSP/SPI/DISPLAY
  */
 
-#define CONFIG_CMD_SPI
 #define CONFIG_LPC32XX_SSP
 #define CONFIG_LPC32XX_SSP_TIMEOUT 100000
 #define CONFIG_CMD_MAX6957
-#define CONFIG_CMD_HD44760
 /*
  * Environment
  */
@@ -176,22 +144,6 @@
 #define CONFIG_ENV_OFFSET_REDUND	0x00120000
 #define CONFIG_ENV_ADDR			0x80000100
 
-/*
- * Provide default ethernet address
- *
- * THIS IS NORMALLY NOT DONE. HERE WE KEEP WHAT WAS IN THE PORTED
- * BOARD CONFIG IN CASE SOME PROVISIONING PROCESS OUT THERE EXPECTS
- * THIS MAC ADDRESS WHEN THE DEVICE HAS STILL ITS DEFAULT CONFIG.
- */
-
-#define CONFIG_ETHADDR			00:12:B4:00:AF:FE
-#define	CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*
- * U-Boot Commands
- */
-#include <config_cmd_default.h>
-
 /*
  * Boot Linux
  */
@@ -199,9 +151,6 @@
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_BOOTDELAY		3
-
 #define CONFIG_BOOTFILE			"uImage"
 #define CONFIG_BOOTARGS			"console=ttyS2,115200n8"
 #define CONFIG_LOADADDR			0x80008000
@@ -214,15 +163,10 @@
 #define CONFIG_SPL_TEXT_BASE 0x00000000
 /* SPL will use SRAM as stack */
 #define CONFIG_SPL_STACK     0x0000FFF8
-#define CONFIG_SPL_BOARD_INIT
 /* Use the framework and generic lib */
 #define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
 /* SPL will use serial */
-#define CONFIG_SPL_SERIAL_SUPPORT
 /* SPL will load U-Boot from NAND offset 0x40000 */
-#define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
 #define CONFIG_SPL_NAND_BOOT