+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* ti_armv7_common.h
*
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
*
- * SPDX-License-Identifier: GPL-2.0+
- *
* The various ARMv7 SoCs from TI all share a number of IP blocks when
* implementing a given feature. Rather than define these in every
* board or even SoC common file, we define a common file to be re-used
#ifndef __CONFIG_TI_ARMV7_COMMON_H__
#define __CONFIG_TI_ARMV7_COMMON_H__
-/*
- * We typically do not contain NOR flash. In the cases where we do, we
- * undefine this later.
- */
-#define CONFIG_SYS_NO_FLASH
-
/* Support both device trees and ATAGs. */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
"bootm_size=0x10000000\0" \
"boot_fdt=try\0"
-#define DEFAULT_MMC_TI_ARGS \
- "mmcdev=0\0" \
- "mmcrootfstype=ext4 rootwait\0" \
- "finduuid=part uuid mmc ${bootpart} uuid\0" \
- "args_mmc=run finduuid;setenv bootargs console=${console} " \
- "${optargs} " \
- "root=PARTUUID=${uuid} rw " \
- "rootfstype=${mmcrootfstype}\0" \
- "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
- "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
- "source ${loadaddr}\0" \
- "bootenvfile=uEnv.txt\0" \
- "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
- "env import -t ${loadaddr} ${filesize}\0" \
- "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenvfile}\0" \
- "loadimage=load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
- "loadfdt=load ${devtype} ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
- "envboot=mmc dev ${mmcdev}; " \
- "if mmc rescan; then " \
- "echo SD/MMC found on device ${mmcdev};" \
- "if run loadbootscript; then " \
- "run bootscript;" \
- "else " \
- "if run loadbootenv; then " \
- "echo Loaded env from ${bootenvfile};" \
- "run importbootenv;" \
- "fi;" \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...;" \
- "run uenvcmd;" \
- "fi;" \
- "fi;" \
- "fi;\0" \
- "mmcloados=run args_mmc; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootz ${loadaddr} - ${fdtaddr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0" \
- "mmcboot=mmc dev ${mmcdev}; " \
- "setenv devnum ${mmcdev}; " \
- "setenv devtype mmc; " \
- "if mmc rescan; then " \
- "echo SD/MMC found on device ${mmcdev};" \
- "if run loadimage; then " \
- "if test ${boot_fit} -eq 1; then " \
- "run loadfit; " \
- "else " \
- "run mmcloados;" \
- "fi;" \
- "fi;" \
- "fi;\0" \
-
#define DEFAULT_FIT_TI_ARGS \
"boot_fit=0\0" \
- "fit_loadaddr=0x88000000\0" \
- "fit_bootfile=fitImage.itb\0" \
+ "fit_loadaddr=0x87000000\0" \
+ "fit_bootfile=fitImage\0" \
"update_to_fit=setenv loadaddr ${fit_loadaddr}; setenv bootfile ${fit_bootfile}\0" \
- "args_fit=setenv bootargs console=${console} \0" \
- "loadfit=run args_fit; bootm ${loadaddr}#${fdtfile};\0" \
+ "loadfit=run args_mmc; bootm ${loadaddr}#${fdtfile};\0" \
/*
* DDR information. If the CONFIG_NR_DRAM_BANKS is not defined,
#define CONFIG_DM_I2C_COMPAT
#endif
-/* McSPI IP block */
-#define CONFIG_SPI
-
-/* GPIO block */
-
/*
* The following are general good-enough settings for U-Boot. We set a
* large malloc pool as we generally have a lot of DDR, and we opt for
* console baudrate of 115200 and use the default baud rate table.
*/
#define CONFIG_SYS_MALLOC_LEN SZ_32M
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_ENV_VARS_UBOOT_CONFIG /* Strongly encouraged */
#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */
/* As stated above, the following choices are optional. */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
/* We set the max number of command args high to avoid HUSH bugs. */
#define CONFIG_SYS_MAXARGS 64
/* Console I/O Buffer Size */
#define CONFIG_SYS_CBSIZE 1024
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
- + sizeof(CONFIG_SYS_PROMPT) + 16)
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
* mtdparts, both for ease of use in U-Boot and for passing information
* on to the Linux kernel.
*/
-#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) || defined(CONFIG_NAND_DAVINCI)
-#define CONFIG_MTD_DEVICE /* Required for mtdparts */
-#define CONFIG_CMD_MTDPARTS
-#endif
-
-#define CONFIG_SUPPORT_RAW_INITRD
-
-/*
- * Common filesystems support. When we have removable storage we
- * enabled a number of useful commands and support.
- */
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
-#define CONFIG_FAT_WRITE
-#endif
/*
* Our platforms make use of SPL to initalize the hardware (primarily
*/
#if !defined(CONFIG_NOR_BOOT) && \
!(defined(CONFIG_QSPI_BOOT) && defined(CONFIG_AM43XX))
-#define CONFIG_SPL_FRAMEWORK
/*
* We also support Falcon Mode so that the Linux kernel can be booted
* of the BSS area. We suggest that the stack be placed at 32MiB after the
* start of DRAM to allow room for all of the above (handled in Kconfig).
*/
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0x80800000
-#endif
#ifndef CONFIG_SPL_BSS_START_ADDR
#define CONFIG_SPL_BSS_START_ADDR 0x80a00000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
/* RAW SD card / eMMC */
-#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
-
-/* spl export command */
-#define CONFIG_CMD_SPL
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1700 /* address 0x2E0000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x1500 /* address 0x2A0000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x200 /* 256KiB */
#endif
-#define CONFIG_SYS_THUMB_BUILD
-
/* General parts of the framework, required. */
-#define CONFIG_SPL_BOARD_INIT
#ifdef CONFIG_NAND
#define CONFIG_SPL_NAND_BASE
#define NETARGS ""
#endif
-#include <config_distro_defaults.h>
-
#endif /* __CONFIG_TI_ARMV7_COMMON_H__ */
projects / u-boot.git / blobdiff