A wide range of Rockchip SoCs are supported in mainline U-Boot
+Warning
+=======
+This document is being moved to doc/board/rockchip, so information on it
+might be incomplete or outdated.
Prerequisites
=============
- Suitable ARM cross compiler, e.g.:
sudo apt-get install gcc-4.7-arm-linux-gnueabi
-
Building
========
-At present 12 RK3288 boards are supported:
+1. To build RK3288 board:
+
+ CROSS_COMPILE=arm-linux-gnueabi- make O=firefly firefly-rk3288_defconfig all
- - EVB RK3288 - use evb-rk3288 configuration
- - Fennec RK3288 - use fennec-rk3288 configuration
- - Firefly RK3288 - use firefly-rk3288 configuration
- - Hisense Chromebook - use chromebook_jerry configuration
- - Asus C100P Chromebook - use chromebook_minnie configuration
- - Asus Chromebit - use chromebook_mickey configuration
- - MiQi RK3288 - use miqi-rk3288 configuration
- - phyCORE-RK3288 RDK - use phycore-rk3288 configuration
- - PopMetal RK3288 - use popmetal-rk3288 configuration
- - Radxa Rock 2 - use rock2 configuration
- - Tinker RK3288 - use tinker-rk3288 configuration
- - Vyasa RK3288 - use vyasa-rk3288 configuration
+ (or you can use another cross compiler if you prefer)
-Two RK3036 boards are supported:
+2. To build RK3308 board:
+ - Get the rkbin
+ => git clone https://github.com/rockchip-linux/rkbin.git
- - EVB RK3036 - use evb-rk3036 configuration
- - Kylin - use kylin_rk3036 configuration
+ - Compile U-Boot
+ => cd /path/to/u-boot
+ => export BL31=/path/to/rkbin/bin/rk33/rk3308_bl31_v2.22.elf
+ => make roc-cc-rk3308_defconfig
+ => make CROSS_COMPILE=aarch64-linux-gnu- all
+ => ./tools/mkimage -n rk3308 -T rksd -d /path/to/rkbin/bin/rk33/rk3308_ddr_589MHz_uart2_m0_v1.26.bin idbloader.img
+ => cat spl/u-boot-spl.bin >> idbloader.img
-One RK3328 board is supported:
+3. To build RK3399 board:
- - EVB RK3328
+ Option 1: Package the image with Rockchip miniloader:
-Size RK3399 boards are supported (aarch64):
+ - Compile U-Boot
- - EBV RK3399 - use evb_rk3399 configuration
- - Firefly RK3399 - use the firefly_rk3399 configuration
- - Puma - use puma_rk3399 configuration
- - Ficus - use ficus-rk3399 configuration
- - Rock960 (Vamrs) - use rock960-rk3399 configuration
- - Bob - use chromebook_bob configuration
+ => cd /path/to/u-boot
+ => make nanopi-neo4-rk3399_defconfig
+ => make
-Four RK3368 boards are supported:
+ - Get the rkbin
- - Sheep - use sheep-rk3368 configuration
- - Lion - use lion-rk3368 configuration
- - Geekbox - use geekbox configuration
- - EVB PX5 - use evb-px5 configuration
+ => git clone https://github.com/rockchip-linux/rkbin.git
-One RK3128 board is supported:
+ - Create trust.img
- - EVB RK3128 - use evb-rk3128 configuration
+ => cd /path/to/rkbin
+ => ./tools/trust_merger RKTRUST/RK3399TRUST.ini
-One RK3229 board is supported:
+ - Create uboot.img
- - EVB RK3229 - use evb-rk3229 configuration
+ => cd /path/to/rkbin
+ => ./tools/loaderimage --pack --uboot /path/to/u-boot/u-boot-dtb.bin uboot.img
-Two RV1108 boards are supported:
+ (Get trust.img and uboot.img)
- - EVB RV1108 - use evb-rv1108 configuration
- - Elgin R1 - use elgin-rv1108 configuration
+ Option 2: Package the image with SPL:
-One RV3188 baord is supported:
+ - Export cross compiler path for aarch64
- - Raxda Rock - use rock configuration
+ - Compile ATF
+ For Puma board.
-For example:
+ => git clone git://git.theobroma-systems.com/arm-trusted-firmware.git
+ => cd arm-trusted-firmware
+ => make CROSS_COMPILE=aarch64-linux-gnu- PLAT=rk3399 bl31
- CROSS_COMPILE=arm-linux-gnueabi- make O=firefly firefly-rk3288_defconfig all
+ (export bl31.bin)
+ => export BL31=/path/to/arm-trusted-firmware/build/rk3399/release/bl31/bl31.bin
+
+ For rest of rk3399 boards.
+
+ => git clone https://github.com/ARM-software/arm-trusted-firmware.git
+ => cd arm-trusted-firmware
+
+ (export cross compiler path for Cortex-M0 MCU likely arm-none-eabi-)
+ => make realclean
+ => make CROSS_COMPILE=aarch64-linux-gnu- PLAT=rk3399
+
+ (export bl31.elf)
+ => export BL31=/path/to/arm-trusted-firmware/build/rk3399/release/bl31/bl31.elf
-(or you can use another cross compiler if you prefer)
+ - Compile PMU M0 firmware
+ This is optional for most of the rk3399 boards and required only for Puma board.
+
+ => git clone git://git.theobroma-systems.com/rk3399-cortex-m0.git
+ => cd rk3399-cortex-m0
+
+ (export cross compiler path for Cortex-M0 PMU)
+ => make CROSS_COMPILE=arm-cortex_m0-eabi-
+
+ (export rk3399m0.bin)
+ => export PMUM0=/path/to/rk3399-cortex-m0/rk3399m0.bin
+
+ - Compile U-Boot
+
+ => cd /path/to/u-boot
+ => make orangepi-rk3399_defconfig
+ => make
+
+ (Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
+ spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
+
+ If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
+ if CONFIG_TPL_OF_CONTROL not enabled)
Writing to the board with USB
=============================
use the existing boot ROM code from SPL.
+Writing to the eMMC with USB on ROC-RK3308-CC
+=============================================
+For USB to work you must get your board into Bootrom mode,
+either by erasing the eMMC or short circuit the GND and D0
+on core board.
+
+Connect the board to your computer via tyepc.
+=> rkdeveloptool db rk3308_loader_v1.26.117.bin
+=> rkdeveloptool wl 0x40 idbloader.img
+=> rkdeveloptool wl 0x4000 u-boot.itb
+=> rkdeveloptool rd
+
+Then you will see the boot log from Debug UART at baud rate 1500000:
+DDR Version V1.26
+REGFB: 0x00000032, 0x00000032
+In
+589MHz
+DDR3
+ Col=10 Bank=8 Row=14 Size=256MB
+msch:1
+Returning to boot ROM...
+
+U-Boot SPL 2020.01-rc1-00225-g34b681327f (Nov 14 2019 - 10:58:04 +0800)
+Trying to boot from MMC1
+INFO: Preloader serial: 2
+NOTICE: BL31: v1.3(release):30f1405
+NOTICE: BL31: Built : 17:08:28, Sep 23 2019
+INFO: Lastlog: last=0x100000, realtime=0x102000, size=0x2000
+INFO: ARM GICv2 driver initialized
+INFO: Using opteed sec cpu_context!
+INFO: boot cpu mask: 1
+INFO: plat_rockchip_pmu_init: pd status 0xe b
+INFO: BL31: Initializing runtime services
+WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will rK
+ERROR: Error initializing runtime service opteed_fast
+INFO: BL31: Preparing for EL3 exit to normal world
+INFO: Entry point address = 0x600000
+INFO: SPSR = 0x3c9
+
+
+U-Boot 2020.01-rc1-00225-g34b681327f (Nov 14 2019 - 10:58:47 +0800)
+
+Model: Firefly ROC-RK3308-CC board
+DRAM: 254 MiB
+MMC: dwmmc@ff480000: 0, dwmmc@ff490000: 1
+rockchip_dnl_key_pressed read adc key val failed
+Net: No ethernet found.
+Hit any key to stop autoboot: 0
+Card did not respond to voltage select!
+switch to partitions #0, OK
+mmc1(part 0) is current device
+Scanning mmc 1:4...
+Found /extlinux/extlinux.conf
+Retrieving file: /extlinux/extlinux.conf
+151 bytes read in 3 ms (48.8 KiB/s)
+1: kernel-mainline
+Retrieving file: /Image
+14737920 bytes read in 377 ms (37.3 MiB/s)
+append: earlycon=uart8250,mmio32,0xff0c0000 console=ttyS2,1500000n8
+Retrieving file: /rk3308-roc-cc.dtb
+28954 bytes read in 4 ms (6.9 MiB/s)
+Flattened Device Tree blob at 01f00000
+Booting using the fdt blob at 0x1f00000
+## Loading Device Tree to 000000000df3a000, end 000000000df44119 ... OK
+
+Starting kernel ...
+[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd042]
+[ 0.000000] Linux version 5.4.0-rc1-00040-g4dc2d508fa47-dirty (andy@B150) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-209
+[ 0.000000] Machine model: Firefly ROC-RK3308-CC board
+[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000ff0c0000 (options '')
+[ 0.000000] printk: bootconsole [uart8250] enabled
+
Booting from an SD card
=======================
cat firefly-rk3288/u-boot-dtb.bin >> out && \
sudo dd if=out of=/dev/sdc seek=64
+Or:
+ ./firefly-rk3288/tools/mkimage -n rk3288 -T rksd -d \
+ firefly-rk3288/spl/u-boot-spl-dtb.bin:firefly-rk3288/u-boot-dtb.bin \
+ out && \
+ sudo dd if=out of=/dev/sdc seek=64
+
If you have an HDMI cable attached you should see a video console.
For evb_rk3036 board:
cat evb-rk3036/u-boot-dtb.bin >> out && \
sudo dd if=out of=/dev/sdc seek=64
+Or:
+ ./evb-rk3036/tools/mkimage -n rk3036 -T rksd -d \
+ evb-rk3036/spl/u-boot-spl.bin:evb-rk3036/u-boot-dtb.bin out && \
+ sudo dd if=out of=/dev/sdc seek=64
+
Note: rk3036 SDMMC and debug uart use the same iomux, so if you boot from SD, the
debug uart must be disabled
To write an image that boots from an SD card (assumed to be /dev/mmcblk0):
- ./tools/mkimage -n rk3288 -T rksd -d ./tpl/u-boot-tpl.bin out &&
- cat ./spl/u-boot-spl-dtb.bin >> out &&
- sudo dd if=out of=/dev/mmcblk0 seek=64 &&
+ sudo dd if=idbloader.img of=/dev/mmcblk0 seek=64 &&
sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 seek=16384
Booting from an SD card on RK3188
truncate -s %2048 u-boot.bin
cat u-boot.bin | split -b 512 --filter='openssl rc4 -K 7C4E0304550509072D2C7B38170D1711' >> out
+Booting from an SD card on Pine64 Rock64 (RK3328)
+=================================================
+
+For Rock64 rk3328 board the following three parts are required:
+TPL, SPL, and the u-boot image tree blob.
+
+ - Write TPL/SPL image at 64 sector
+
+ => sudo dd if=idbloader.img of=/dev/mmcblk0 seek=64
+
+ - Write u-boot image tree blob at 16384 sector
+
+ => sudo dd if=u-boot.itb of=/dev/mmcblk0 seek=16384
+
+Booting from an SD card on RK3399
+=================================
+
+To write an image that boots from an SD card (assumed to be /dev/sdc):
+
+Option 1: Package the image with Rockchip miniloader:
+
+ - Create idbloader.img
+
+ => cd /path/to/u-boot
+ => ./tools/mkimage -n rk3399 -T rksd -d /path/to/rkbin/bin/rk33/rk3399_ddr_800MHz_v1.20.bin idbloader.img
+ => cat /path/to/rkbin/bin/rk33/rk3399_miniloader_v1.19.bin >> idbloader.img
+
+ - Write idbloader.img at 64 sector
+
+ => sudo dd if=idbloader.img of=/dev/sdc seek=64
+
+ - Write trust.img at 24576
+
+ => sudo dd if=trust.img of=/dev/sdc seek=24576
+
+ - Write uboot.img at 16384 sector
+
+ => sudo dd if=uboot.img of=/dev/sdc seek=16384
+ => sync
+
+Put this SD (or micro-SD) card into your board and reset it. You should see
+something like:
+
+DDR Version 1.20 20190314
+In
+Channel 0: DDR3, 933MHz
+Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
+no stride
+ch 0 ddrconfig = 0x101, ddrsize = 0x20
+pmugrf_os_reg[2] = 0x10006281, stride = 0x17
+OUT
+Boot1: 2019-03-14, version: 1.19
+CPUId = 0x0
+ChipType = 0x10, 239
+mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
+mmc: ERROR: Card did not respond to voltage select!
+emmc reinit
+mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
+mmc: ERROR: Card did not respond to voltage select!
+emmc reinit
+mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
+mmc: ERROR: Card did not respond to voltage select!
+SdmmcInit=2 1
+mmc0:cmd5,20
+SdmmcInit=0 0
+BootCapSize=0
+UserCapSize=60543MB
+FwPartOffset=2000 , 0
+StorageInit ok = 45266
+SecureMode = 0
+SecureInit read PBA: 0x4
+SecureInit read PBA: 0x404
+SecureInit read PBA: 0x804
+SecureInit read PBA: 0xc04
+SecureInit read PBA: 0x1004
+SecureInit read PBA: 0x1404
+SecureInit read PBA: 0x1804
+SecureInit read PBA: 0x1c04
+SecureInit ret = 0, SecureMode = 0
+atags_set_bootdev: ret:(0)
+GPT 0x3380ec0 signature is wrong
+recovery gpt...
+GPT 0x3380ec0 signature is wrong
+recovery gpt fail!
+LoadTrust Addr:0x4000
+No find bl30.bin
+Load uboot, ReadLba = 2000
+hdr 0000000003380880 + 0x0:0x88,0x41,0x3e,0x97,0xe6,0x61,0x54,0x23,0xe9,0x5a,0xd1,0x2b,0xdc,0x2f,0xf9,0x35,
+
+Load OK, addr=0x200000, size=0x9c9c0
+RunBL31 0x10000
+NOTICE: BL31: v1.3(debug):370ab80
+NOTICE: BL31: Built : 09:23:41, Mar 4 2019
+NOTICE: BL31: Rockchip release version: v1.1
+INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
+INFO: Using opteed sec cpu_context!
+INFO: boot cpu mask: 0
+INFO: plat_rockchip_pmu_init(1181): pd status 3e
+INFO: BL31: Initializing runtime services
+INFO: BL31: Initializing BL32
+INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-195-g8f090d20 #6 Fri Dec 7 06:11:20 UTC 2018 aarch64)
+
+INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2
+
+INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
+INFO: BL31: Preparing for EL3 exit to normal world
+INFO: Entry point address = 0x200000
+INFO: SPSR = 0x3c9
+
+
+U-Boot 2019.04-rc4-00136-gfd121f9641-dirty (Apr 16 2019 - 14:02:47 +0530)
+
+Model: FriendlyARM NanoPi NEO4
+DRAM: 1022 MiB
+MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0
+Loading Environment from MMC... *** Warning - bad CRC, using default environment
+
+In: serial@ff1a0000
+Out: serial@ff1a0000
+Err: serial@ff1a0000
+Model: FriendlyARM NanoPi NEO4
+Net: eth0: ethernet@fe300000
+Hit any key to stop autoboot: 0
+=>
+
+Option 2: Package the image with SPL:
+
+ - Prefix rk3399 header to SPL image
+
+ => cd /path/to/u-boot
+ => ./tools/mkimage -n rk3399 -T rksd -d spl/u-boot-spl-dtb.bin out
+
+ - Write prefixed SPL at 64th sector
+
+ => sudo dd if=out of=/dev/sdc seek=64
+
+ - Write U-Boot proper at 16384 sector
+
+ => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
+ => sync
+
+Put this SD (or micro-SD) card into your board and reset it. You should see
+something like:
+
+U-Boot SPL board init
+Trying to boot from MMC1
+
+
+U-Boot 2019.01-00004-g14db5ee998 (Mar 11 2019 - 13:18:41 +0530)
+
+Model: Orange Pi RK3399 Board
+DRAM: 2 GiB
+MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0
+Loading Environment from MMC... OK
+In: serial@ff1a0000
+Out: serial@ff1a0000
+Err: serial@ff1a0000
+Model: Orange Pi RK3399 Board
+Net: eth0: ethernet@fe300000
+Hit any key to stop autoboot: 0
+=>
+
+Option 3: Package the image with TPL:
+
+ - Write tpl+spl at 64th sector
+
+ => sudo dd if=idbloader.img of=/dev/sdc seek=64
+
+ - Write U-Boot proper at 16384 sector
+
+ => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
+ => sync
+
+Put this SD (or micro-SD) card into your board and reset it. You should see
+something like:
+
+U-Boot TPL board init
+Trying to boot from BOOTROM
+Returning to boot ROM...
+
+U-Boot SPL board init
+Trying to boot from MMC1
+
+
+U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
+
+Model: Orange Pi RK3399 Board
+DRAM: 2 GiB
+MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0
+Loading Environment from MMC... OK
+In: serial@ff1a0000
+Out: serial@ff1a0000
+Err: serial@ff1a0000
+Model: Orange Pi RK3399 Board
+Net: eth0: ethernet@fe300000
+Hit any key to stop autoboot: 0
+=>
Using fastboot on rk3288
========================
offset 128KB and the whole image is padded to 4MB which is the SPI flash size.
The position of U-Boot is controlled with this setting in U-Boot:
- #define CONFIG_SYS_SPI_U_BOOT_OFFS (128 << 10)
+ #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
If you have a Dediprog em100pro connected then you can write the image with:
http://rockchip.wikidot.com/partitions
--
+27 Mar 2019
24 June 2015
projects / u-boot.git / blobdiff