*/
#include <common.h>
+#include <init.h>
+#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux-mx51.h>
+#include <linux/delay.h>
#include <linux/errno.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/crm_regs.h>
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg esdhc_cfg[2] = {
- {MMC_SDHC1_BASE_ADDR},
- {MMC_SDHC2_BASE_ADDR},
-};
-#endif
-
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ gd->ram_size = get_ram_size((void *)CFG_SYS_SDRAM_BASE,
PHYS_SDRAM_1_SIZE);
return 0;
}
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
u32 rev = get_cpu_rev();
rev |= BOARD_REV_2_0 << BOARD_VER_OFFSET;
return rev;
}
+#endif
#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_DSE_HIGH)
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
}
-static void setup_iomux_fec(void)
-{
- static const iomux_v3_cfg_t fec_pads[] = {
- NEW_PAD_CTRL(MX51_PAD_EIM_EB2__FEC_MDIO, PAD_CTL_HYS |
- PAD_CTL_PUS_22K_UP | PAD_CTL_ODE |
- PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
- MX51_PAD_NANDF_CS3__FEC_MDC,
- NEW_PAD_CTRL(MX51_PAD_EIM_CS3__FEC_RDATA3, MX51_PAD_CTRL_2),
- NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, MX51_PAD_CTRL_2),
- NEW_PAD_CTRL(MX51_PAD_EIM_EB3__FEC_RDATA1, MX51_PAD_CTRL_2),
- MX51_PAD_NANDF_D9__FEC_RDATA0,
- MX51_PAD_NANDF_CS6__FEC_TDATA3,
- MX51_PAD_NANDF_CS5__FEC_TDATA2,
- MX51_PAD_NANDF_CS4__FEC_TDATA1,
- MX51_PAD_NANDF_D8__FEC_TDATA0,
- MX51_PAD_NANDF_CS7__FEC_TX_EN,
- MX51_PAD_NANDF_CS2__FEC_TX_ER,
- MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK,
- NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__FEC_COL, MX51_PAD_CTRL_4),
- NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__FEC_RX_CLK, MX51_PAD_CTRL_4),
- MX51_PAD_EIM_CS5__FEC_CRS,
- MX51_PAD_EIM_CS4__FEC_RX_ER,
- NEW_PAD_CTRL(MX51_PAD_NANDF_D11__FEC_RX_DV, MX51_PAD_CTRL_4),
- };
-
- imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-}
-
#ifdef CONFIG_MXC_SPI
static void setup_iomux_spi(void)
{
}
#endif
-#ifdef CONFIG_USB_EHCI_MX5
-#define MX51EVK_USBH1_HUB_RST IMX_GPIO_NR(1, 7)
-#define MX51EVK_USBH1_STP IMX_GPIO_NR(1, 27)
-#define MX51EVK_USB_CLK_EN_B IMX_GPIO_NR(2, 1)
-#define MX51EVK_USB_PHY_RESET IMX_GPIO_NR(2, 5)
-
-static void setup_usb_h1(void)
-{
- static const iomux_v3_cfg_t usb_h1_pads[] = {
- MX51_PAD_USBH1_CLK__USBH1_CLK,
- MX51_PAD_USBH1_DIR__USBH1_DIR,
- MX51_PAD_USBH1_STP__USBH1_STP,
- MX51_PAD_USBH1_NXT__USBH1_NXT,
- MX51_PAD_USBH1_DATA0__USBH1_DATA0,
- MX51_PAD_USBH1_DATA1__USBH1_DATA1,
- MX51_PAD_USBH1_DATA2__USBH1_DATA2,
- MX51_PAD_USBH1_DATA3__USBH1_DATA3,
- MX51_PAD_USBH1_DATA4__USBH1_DATA4,
- MX51_PAD_USBH1_DATA5__USBH1_DATA5,
- MX51_PAD_USBH1_DATA6__USBH1_DATA6,
- MX51_PAD_USBH1_DATA7__USBH1_DATA7,
-
- NEW_PAD_CTRL(MX51_PAD_GPIO1_7__GPIO1_7, 0), /* H1 hub reset */
- MX51_PAD_EIM_D17__GPIO2_1,
- MX51_PAD_EIM_D21__GPIO2_5, /* PHY reset */
- };
-
- imx_iomux_v3_setup_multiple_pads(usb_h1_pads, ARRAY_SIZE(usb_h1_pads));
-}
-
-int board_ehci_hcd_init(int port)
-{
- /* Set USBH1_STP to GPIO and toggle it */
- imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_USBH1_STP__GPIO1_27,
- MX51_USBH_PAD_CTRL));
-
- gpio_direction_output(MX51EVK_USBH1_STP, 0);
- gpio_direction_output(MX51EVK_USB_PHY_RESET, 0);
- mdelay(10);
- gpio_set_value(MX51EVK_USBH1_STP, 1);
-
- /* Set back USBH1_STP to be function */
- imx_iomux_v3_setup_pad(MX51_PAD_USBH1_STP__USBH1_STP);
-
- /* De-assert USB PHY RESETB */
- gpio_set_value(MX51EVK_USB_PHY_RESET, 1);
-
- /* Drive USB_CLK_EN_B line low */
- gpio_direction_output(MX51EVK_USB_CLK_EN_B, 0);
-
- /* Reset USB hub */
- gpio_direction_output(MX51EVK_USBH1_HUB_RST, 0);
- mdelay(2);
- gpio_set_value(MX51EVK_USBH1_HUB_RST, 1);
- return 0;
-}
-#endif
-
static void power_init(void)
{
unsigned int val;
struct pmic *p;
int ret;
- ret = pmic_init(CONFIG_FSL_PMIC_BUS);
+ ret = pmic_init(CFG_FSL_PMIC_BUS);
if (ret)
return;
imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_EIM_A20__GPIO2_14,
NO_PAD_CTRL));
+ gpio_request(IMX_GPIO_NR(2, 14), "gpio2_14");
gpio_direction_output(IMX_GPIO_NR(2, 14), 0);
udelay(500);
gpio_set_value(IMX_GPIO_NR(2, 14), 1);
}
-#ifdef CONFIG_FSL_ESDHC_IMX
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret;
-
- imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_0__GPIO1_0,
- NO_PAD_CTRL));
- gpio_direction_input(IMX_GPIO_NR(1, 0));
- imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_6__GPIO1_6,
- NO_PAD_CTRL));
- gpio_direction_input(IMX_GPIO_NR(1, 6));
-
- if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
- ret = !gpio_get_value(IMX_GPIO_NR(1, 0));
- else
- ret = !gpio_get_value(IMX_GPIO_NR(1, 6));
-
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- static const iomux_v3_cfg_t sd1_pads[] = {
- NEW_PAD_CTRL(MX51_PAD_SD1_CMD__SD1_CMD, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_CLK__SD1_CLK, PAD_CTL_DSE_MAX |
- PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_DATA0__SD1_DATA0, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_DATA1__SD1_DATA1, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_DATA2__SD1_DATA2, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_DATA3__SD1_DATA3, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_GPIO1_0__SD1_CD, PAD_CTL_HYS),
- NEW_PAD_CTRL(MX51_PAD_GPIO1_1__SD1_WP, PAD_CTL_HYS),
- };
-
- static const iomux_v3_cfg_t sd2_pads[] = {
- NEW_PAD_CTRL(MX51_PAD_SD2_CMD__SD2_CMD,
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD2_CLK__SD2_CLK,
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD2_DATA0__SD2_DATA0,
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD2_DATA1__SD2_DATA1,
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD2_DATA2__SD2_DATA2,
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD2_DATA3__SD2_DATA3,
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_GPIO1_6__GPIO1_6, PAD_CTL_HYS),
- NEW_PAD_CTRL(MX51_PAD_GPIO1_5__GPIO1_5, PAD_CTL_HYS),
- };
-
- u32 index;
- int ret;
-
- esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-
- for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM;
- index++) {
- switch (index) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(sd1_pads,
- ARRAY_SIZE(sd1_pads));
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(sd2_pads,
- ARRAY_SIZE(sd2_pads));
- break;
- default:
- printf("Warning: you configured more ESDHC controller"
- "(%d) as supported by the board(2)\n",
- CONFIG_SYS_FSL_ESDHC_NUM);
- return -EINVAL;
- }
- ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
- if (ret)
- return ret;
- }
- return 0;
-}
-#endif
-
int board_early_init_f(void)
{
setup_iomux_uart();
- setup_iomux_fec();
-#ifdef CONFIG_USB_EHCI_MX5
- setup_usb_h1();
-#endif
setup_iomux_lcd();
return 0;
projects / u-boot.git / blobdiff