board: st: move type-c stusb1600 controller code in a driver

[u-boot.git] / configs / sama5d4ek_nandflash_defconfig

diff --git a/configs/sama5d4ek_nandflash_defconfig b/configs/sama5d4ek_nandflash_defconfig
index 7922f62a5b9b96956adfaae6668a8865e12c810c..fcd6eec25c4d64baf221f26a71753e3800ae6f18 100644 (file)
--- a/configs/sama5d4ek_nandflash_defconfig
+++ b/configs/sama5d4ek_nandflash_defconfig
@@ -7,6 +7,8 @@ CONFIG_SPL_GPIO_SUPPORT=y
 CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_SPL_TEXT_BASE=0x200000
 CONFIG_SPL_SERIAL_SUPPORT=y
 CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
 CONFIG_NR_DRAM_BANKS=1
@@ -14,8 +16,8 @@ CONFIG_SPL=y
 CONFIG_DEBUG_UART_BOARD_INIT=y
 CONFIG_DEBUG_UART_BASE=0xfc00c000
 CONFIG_DEBUG_UART_CLOCK=88000000
+CONFIG_ENV_OFFSET_REDUND=0x100000
 CONFIG_DEBUG_UART=y
-CONFIG_SPL_TEXT_BASE=0x200000
 CONFIG_ENV_VARS_UBOOT_CONFIG=y
 CONFIG_FIT=y
 CONFIG_NAND_BOOT=y
@@ -43,7 +45,6 @@ CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d4ek"
 CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dma-names dmas"
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_OFFSET_REDUND=0x100000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_DM=y
 CONFIG_SPL_DM=y
@@ -53,14 +54,11 @@ CONFIG_SPL_CLK=y
 CONFIG_CLK_AT91=y
 CONFIG_AT91_UTMI=y
 CONFIG_AT91_H32MX=y
-CONFIG_DM_GPIO=y
 CONFIG_AT91_GPIO=y
 CONFIG_DM_MMC=y
 CONFIG_GENERIC_ATMEL_MCI=y
-CONFIG_MTD_RAW_NAND=y
-# CONFIG_SYS_NAND_USE_FLASH_BBT is not set
 CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
+# CONFIG_SYS_NAND_USE_FLASH_BBT is not set
 CONFIG_NAND_ATMEL=y
 CONFIG_PMECC_CAP=8
 CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER=y
@@ -73,7 +71,6 @@ CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_AT91=y
 CONFIG_DM_SERIAL=y
-CONFIG_DEBUG_UART_ATMEL=y
 CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_ATMEL_USART=y
 CONFIG_SPI=y
@@ -88,4 +85,6 @@ CONFIG_USB_STORAGE=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_ATMEL_USBA=y
 CONFIG_DM_VIDEO=y
+# CONFIG_VIDEO_BPP8 is not set
+# CONFIG_VIDEO_BPP32 is not set
 CONFIG_ATMEL_HLCD=y