CONFIG_ARM=y
CONFIG_ARCH_IMX8=y
CONFIG_SYS_TEXT_BASE=0x80020000
-CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SYS_MALLOC_LEN=0x2400000
+CONFIG_SYS_MALLOC_F_LEN=0x8000
+CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SYS_MALLOC_F_LEN=0x8000
CONFIG_NR_DRAM_BANKS=3
CONFIG_ENV_SIZE=0x1000
CONFIG_ENV_OFFSET=0x400000
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qm-mek"
CONFIG_SPL_TEXT_BASE=0x100000
-CONFIG_SPL_LOAD_IMX_CONTAINER=y
-CONFIG_IMX_CONTAINER_CFG="board/freescale/imx8qm_mek/uboot-container.cfg"
CONFIG_TARGET_IMX8QM_MEK=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_SPL_MMC=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_DRIVERS_MISC=y
CONFIG_SPL=y
+CONFIG_SPL_LOAD_IMX_CONTAINER=y
+CONFIG_IMX_CONTAINER_CFG="board/freescale/imx8qm_mek/uboot-container.cfg"
+CONFIG_SYS_LOAD_ADDR=0x80280000
+CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_SYSTEM_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/imx8qm_mek/imximage.cfg"
CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if test ${sec_boot} = yes; then if run loadcntr; then run mmcboot; else run netboot; fi; else if run loadimage; then run mmcboot; else run netboot; fi; fi; fi; else booti ${loadaddr} - ${fdt_addr}; fi"
CONFIG_LOG=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
CONFIG_SPL_SEPARATE_BSS=y
-CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x800
CONFIG_SPL_POWER_DOMAIN=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_SPL_WATCHDOG=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_CPU=y
# CONFIG_BOOTM_NETBSD is not set
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_SPL_DM=y
CONFIG_SPL_CLK=y
CONFIG_CLK_IMX8=y
CONFIG_I2C_MUX=y
CONFIG_I2C_MUX_PCA954x=y
CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_FSL_USDHC=y
CONFIG_PHYLIB=y
CONFIG_PHY_ADDR_ENABLE=y