+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2006-2010
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_DISPLAY_BOARDINFO
-
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC834x 1 /* MPC834x family */
#define CONFIG_MPC8349 1 /* MPC8349 specific */
-#define CONFIG_MPC8349EMDS 1 /* MPC8349EMDS board specific */
-
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
#define CONFIG_PCI_66M
#ifdef CONFIG_PCI_66M
#endif
#ifdef CONFIG_PCISLAVE
-#define CONFIG_PCI
#define CONFIG_83XX_PCICLK 66666666 /* in Hz */
#endif /* CONFIG_PCISLAVE */
#endif
#endif
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
-
#define CONFIG_SYS_IMMR 0xE0000000
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
/*
- * define CONFIG_SYS_FSL_DDR2 to use unified DDR driver
- * undefine it to use old spd_sdram.c
+ * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver
+ * unselect it to use old spd_sdram.c
*/
-#define CONFIG_SYS_FSL_DDR2
-#ifdef CONFIG_SYS_FSL_DDR2
-#define CONFIG_SYS_FSL_DDRC_GEN2
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS1 0x52
#define SPD_EEPROM_ADDRESS2 0x51
-#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#endif
/*
* 32-bit data path mode.
/*
* FLASH on the Local Bus
*/
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
#define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
-/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
| BR_PS_16 /* 16 bit port */ \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
/*
/*
* Serial Port
*/
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* SPI */
-#define CONFIG_MPC8XXX_SPI
#undef CONFIG_SOFT_SPI /* SPI bit-banged */
/* GPIOs. Used as SPI chip selects */
#undef PCI_ONE_PCI1
#endif
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_83XX_PCI_STREAMING
#undef CONFIG_EEPRO100
/*
* TSEC configuration
*/
-#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#if defined(CONFIG_TSEC_ENET)
* Environment
*/
#ifndef CONFIG_SYS_RAMBOOT
- #define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR \
(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#else
- #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
- #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
-#define CONFIG_CMD_DATE
-
-#if defined(CONFIG_PCI)
- #define CONFIG_CMD_PCI
-#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
- /* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
- /* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
*/
/* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
#define CONFIG_HAS_ETH0
#endif
-#define CONFIG_HOSTNAME mpc8349emds
+#define CONFIG_HOSTNAME "mpc8349emds"
#define CONFIG_ROOTPATH "/nfsroot/rootfs"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_PREBOOT "echo;" \
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
projects / u-boot.git / blobdiff