+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
*
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_DISPLAY_BOARDINFO
-
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
-#define CONFIG_MPC830x 1 /* MPC830x family */
-#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
-#define CONFIG_MPC8308RDB 1 /* MPC8308RDB board specific */
-
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
-
-#define CONFIG_MISC_INIT_R
-
-/* new uImage format support */
-#define CONFIG_FIT 1
-#define CONFIG_FIT_VERBOSE 1
-
-#define CONFIG_MMC 1
#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
-#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ESDHC_USE_PIO
-
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
#endif
/*
#define CONFIG_TSEC1
#define CONFIG_VSC7385_ENET
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
-#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
-
/*
* Hardware Reset Configuration Word
* if CLKIN is 66.66MHz, then
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/*
/*
* FLASH on the Local Bus
*/
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
/*
* Serial Port
*/
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
* due to a pinmux conflict between GPIO9 (SPI chip select )and the TSEC2 pins.
*/
#ifdef CONFIG_MPC8XXX_SPI
-#define CONFIG_CMD_SPI
#define CONFIG_USE_SPIFLASH
-#define CONFIG_CMD_SF
#endif
/*
/* enable PCIE clock */
#define CONFIG_SYS_SCCR_PCIEXP1CM 1
-#define CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
/*
* TSEC
*/
-#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
/*
* TSEC ethernet configuration
*/
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1_NAME "eTSEC0"
#define CONFIG_TSEC2_NAME "eTSEC1"
#define TSEC1_PHY_ADDR 2
/*
* Environment
*/
-#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/*
* Core HID Setup
#define CONFIG_HAS_ETH1
#endif
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
projects / u-boot.git / blobdiff