/arc Files generic to ARC architecture
/arm Files generic to ARM architecture
/avr32 Files generic to AVR32 architecture
- /blackfin Files generic to Analog Devices Blackfin architecture
/m68k Files generic to m68k architecture
/microblaze Files generic to microblaze architecture
/mips Files generic to MIPS architecture
/powerpc Files generic to PowerPC architecture
/sandbox Files generic to HW-independent "sandbox"
/sh Files generic to SH architecture
- /sparc Files generic to SPARC architecture
/x86 Files generic to x86 architecture
/api Machine/arch independent API for external apps
/board Board dependent files
- stack is optionally in SDRAM, if CONFIG_SPL_STACK_R is defined and
CONFIG_SPL_STACK_R_ADDR points into SDRAM
- preloader_console_init() can be called here - typically this is
- done by defining CONFIG_SPL_BOARD_INIT and then supplying a
+ done by selecting CONFIG_SPL_BOARD_INIT and then supplying a
spl_board_init() function containing this call
- loads U-Boot or (in falcon mode) Linux
CONFIG_SYS_FSL_IFC_LE
Defines the IFC controller register space as Little Endian
+ CONFIG_SYS_FSL_IFC_CLK_DIV
+ Defines divider of platform clock(clock input to IFC controller).
+
+ CONFIG_SYS_FSL_LBC_CLK_DIV
+ Defines divider of platform clock(clock input to eLBC controller).
+
CONFIG_SYS_FSL_PBL_PBI
It enables addition of RCW (Power on reset configuration) in built image.
Please refer doc/README.pblimage for more details
Select high exception vectors of the ARM core, e.g., do not
clear the V bit of the c1 register of CP15.
- CONFIG_SYS_THUMB_BUILD
-
- Use this flag to build U-Boot using the Thumb instruction
- set for ARM architectures. Thumb instruction set provides
- better code density. For ARM architectures that support
- Thumb2 this flag will result in Thumb2 code generated by
- GCC.
-
- CONFIG_ARM_ERRATA_716044
- CONFIG_ARM_ERRATA_742230
- CONFIG_ARM_ERRATA_743622
- CONFIG_ARM_ERRATA_751472
- CONFIG_ARM_ERRATA_761320
- CONFIG_ARM_ERRATA_773022
- CONFIG_ARM_ERRATA_774769
- CONFIG_ARM_ERRATA_794072
-
- If set, the workarounds for these ARM errata are applied early
- during U-Boot startup. Note that these options force the
- workarounds to be applied; no CPU-type/version detection
- exists, unlike the similar options in the Linux kernel. Do not
- set these options unless they apply!
-
COUNTER_FREQUENCY
Generic timer clock source frequency.
different from COUNTER_FREQUENCY, and can only be determined
at run time.
- NOTE: The following can be machine specific errata. These
- do have ability to provide rudimentary version and machine
- specific checks, but expect no product checks.
- CONFIG_ARM_ERRATA_430973
- CONFIG_ARM_ERRATA_454179
- CONFIG_ARM_ERRATA_621766
- CONFIG_ARM_ERRATA_798870
- CONFIG_ARM_ERRATA_801819
-
- Tegra SoC options:
CONFIG_TEGRA_SUPPORT_NON_SECURE
CONFIG_CMD_AES AES 128 CBC encrypt/decrypt
CONFIG_CMD_ASKENV * ask for env variable
CONFIG_CMD_BDI bdinfo
- CONFIG_CMD_BEDBUG * Include BedBug Debugger
- CONFIG_CMD_BMP * BMP support
- CONFIG_CMD_BSP * Board specific commands
CONFIG_CMD_BOOTD bootd
CONFIG_CMD_BOOTI * ARM64 Linux kernel Image support
CONFIG_CMD_CACHE * icache, dcache
- CONFIG_CMD_CLK * clock command support
CONFIG_CMD_CONSOLE coninfo
- CONFIG_CMD_CRC32 * crc32
- CONFIG_CMD_DATE * support for RTC, date/time...
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
- CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
- CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
- CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
- CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
- CONFIG_CMD_DTT * Digital Therm and Thermostat
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EDITENV edit env variable
- CONFIG_CMD_EEPROM * EEPROM read/write support
- CONFIG_CMD_EEPROM_LAYOUT* EEPROM layout aware commands
CONFIG_CMD_ELF * bootelf, bootvx
- CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
- CONFIG_CMD_ENV_FLAGS * display details about env flags
CONFIG_CMD_ENV_EXISTS * check existence of env variable
CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_EXT2 * ext2 command support
that work for multiple fs types
CONFIG_CMD_FS_UUID * Look up a filesystem UUID
CONFIG_CMD_SAVEENV saveenv
- CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT command support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
- CONFIG_CMD_FUSE * Device fuse support
- CONFIG_CMD_GETTIME * Get time since boot
CONFIG_CMD_GO * the 'go' command (exec code)
CONFIG_CMD_GREPENV * search environment
- CONFIG_CMD_HASH * calculate hash / digest
CONFIG_CMD_I2C * I2C serial bus support
- CONFIG_CMD_IDE * IDE harddisk support
CONFIG_CMD_IMI iminfo
CONFIG_CMD_IMLS List all images found in NOR flash
CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
- CONFIG_CMD_IMMAP * IMMR dump support
- CONFIG_CMD_IOTRACE * I/O tracing for debugging
CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_INI * import data from an ini file into the env
- CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_ITEST Integer/string test of 2 values
- CONFIG_CMD_JFFS2 * JFFS2 Support
- CONFIG_CMD_KGDB * kgdb
CONFIG_CMD_LDRINFO * ldrinfo (display Blackfin loader)
CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
(169.254.*.*)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
CONFIG_CMD_SF * Read/write/erase SPI NOR flash
- CONFIG_CMD_SHA1SUM * print sha1 memory digest
- (requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
tree is available in the global data as gd->fdt_blob.
U-Boot needs to get its device tree from somewhere. This can
- be done using one of the two options below:
+ be done using one of the three options below:
CONFIG_OF_EMBED
If this variable is defined, U-Boot will embed a device tree
still use the individual files if you need something more
exotic.
+ CONFIG_OF_BOARD
+ If this variable is defined, U-Boot will use the device tree
+ provided by the board at runtime instead of embedding one with
+ the image. Only boards defining board_fdt_blob_setup() support
+ this option (see include/fdtdec.h file).
+
- Watchdog:
CONFIG_WATCHDOG
If this variable is defined, it enables watchdog
disk/part_efi.c
CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
- If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
+ If IDE or SCSI support is enabled (CONFIG_IDE or
CONFIG_SCSI) you must configure support for at
least one non-MTD partition type as well.
CONFIG_SH_MMCIF_CLK
Define the clock frequency for MMCIF
- CONFIG_GENERIC_MMC
- Enable the generic MMC driver
-
CONFIG_SUPPORT_EMMC_BOOT
Enable some additional features of the eMMC boot partitions.
This will also enable the command "fatwrite" enabling the
user to write files to FAT.
-- CBFS (Coreboot Filesystem) support:
- CONFIG_CMD_CBFS
-
- Define this to enable support for reading from a Coreboot
- filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
- and cbfsload.
-
- FAT(File Allocation Table) filesystem cluster size:
CONFIG_FS_FAT_MAX_CLUSTSIZE
CONFIG_SYS_DIU_ADDR
CONFIG_VIDEO
- CONFIG_CMD_BMP
CONFIG_CFB_CONSOLE
CONFIG_VIDEO_SW_CURSOR
CONFIG_VGA_AS_SINGLE_DEVICE
320x240. Black & white.
- Normally display is black on white background; define
- CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
-
CONFIG_LCD_ALIGNMENT
Normally the LCD is page-aligned (typically 4KB). If this is
can be displayed via the splashscreen support or the
bmp command.
-- Do compressing for memory range:
- CONFIG_CMD_ZIP
-
- If this option is set, it would use zlib deflate method
- to compress the specified memory at its best effort.
-
- Compression support:
CONFIG_GZIP
the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
be at least 4MB.
- CONFIG_LZMA
-
- If this option is set, support for lzma compressed
- images is included.
-
- Note: The LZMA algorithm adds between 2 and 4KB of code and it
- requires an amount of dynamic memory that is given by the
- formula:
-
- (1846 + 768 << (lc + lp)) * sizeof(uint16)
-
- Where lc and lp stand for, respectively, Literal context bits
- and Literal pos bits.
-
- This value is upper-bounded by 14MB in the worst case. Anyway,
- for a ~4MB large kernel image, we have lc=3 and lp=0 for a
- total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
- a very small buffer.
-
- Use the lzmainfo tool to determinate the lc and lp values and
- then calculate the amount of needed dynamic memory (ensuring
- the appropriate CONFIG_SYS_MALLOC_LEN value).
-
CONFIG_LZO
If this option is set, support for LZO compressed images
A byte containing the id of the VLAN.
-- Status LED: CONFIG_STATUS_LED
+- Status LED: CONFIG_LED_STATUS
Several configurations allow to display the current
status using a LED. For instance, the LED will blink
soon as a reply to a BOOTP request was received, and
start blinking slow once the Linux kernel is running
(supported by a status LED driver in the Linux
- kernel). Defining CONFIG_STATUS_LED enables this
+ kernel). Defining CONFIG_LED_STATUS enables this
feature in U-Boot.
Additional options:
- CONFIG_GPIO_LED
+ CONFIG_LED_STATUS_GPIO
The status LED can be connected to a GPIO pin.
In such cases, the gpio_led driver can be used as a
- status LED backend implementation. Define CONFIG_GPIO_LED
+ status LED backend implementation. Define CONFIG_LED_STATUS_GPIO
to include the gpio_led driver in the U-Boot binary.
CONFIG_GPIO_LED_INVERTED_TABLE
If you do not have i2c muxes on your board, omit this define.
-- Legacy I2C Support: CONFIG_HARD_I2C
-
- NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
- provides the following compelling advantages:
-
- - more than one i2c adapter is usable
- - approved multibus support
- - better i2c mux support
-
- ** Please consider updating your I2C driver now. **
-
- These enable legacy I2C serial bus commands. Defining
- CONFIG_HARD_I2C will include the appropriate I2C driver
- for the selected CPU.
-
- This will allow you to use i2c commands at the u-boot
- command line (as long as you set CONFIG_CMD_I2C in
- CONFIG_COMMANDS) and communicate with i2c based realtime
- clock chips. See common/cmd_i2c.c for a description of the
- command line interface.
-
- CONFIG_HARD_I2C selects a hardware I2C controller.
-
- There are several other quantities that must also be
- defined when you define CONFIG_HARD_I2C.
-
- In both cases you will need to define CONFIG_SYS_I2C_SPEED
- to be the frequency (in Hz) at which you wish your i2c bus
- to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
- the CPU's i2c node address).
-
- Now, the u-boot i2c code for the mpc8xx
- (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
- and so its address should therefore be cleared to 0 (See,
- eg, MPC823e User's Manual p.16-473). So, set
- CONFIG_SYS_I2C_SLAVE to 0.
-
- CONFIG_SYS_I2C_INIT_MPC5XXX
-
- When a board is reset during an i2c bus transfer
- chips might think that the current transfer is still
- in progress. Reset the slave devices by sending start
- commands until the slave device responds.
-
- That's all that's required for CONFIG_HARD_I2C.
-
+- Legacy I2C Support:
If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
then the following macros need to be defined (examples are
from include/configs/lwmon.h):
custom i2c_init_board() routine in boards/xxx/board.c
is run early in the boot sequence.
- CONFIG_SYS_I2C_BOARD_LATE_INIT
-
- An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
- defined a custom i2c_board_late_init() routine in
- boards/xxx/board.c is run AFTER the operations in i2c_init()
- is completed. This callpoint can be used to unreset i2c bus
- using CPU i2c controller register accesses for CPUs whose i2c
- controller provide such a method. It is called at the end of
- i2c_init() to allow i2c_init operations to setup the i2c bus
- controller on the CPU (e.g. setting bus speed & slave address).
-
- CONFIG_I2CFAST (PPC405GP|PPC405EP only)
-
- This option enables configuration of bi_iic_fast[] flags
- in u-boot bd_info structure based on u-boot environment
- variable "i2cfast". (see also i2cfast)
-
CONFIG_I2C_MULTI_BUS
This option allows the use of multiple I2C buses, each of which
If defined, then this indicates the I2C bus number for the RTC.
If not defined, then U-Boot assumes that RTC is on I2C bus 0.
- CONFIG_SYS_DTT_BUS_NUM
-
- If defined, then this indicates the I2C bus number for the DTT.
- If not defined, then U-Boot assumes that DTT is on I2C bus 0.
-
- CONFIG_SYS_I2C_DTT_ADDR:
-
- If defined, specifies the I2C address of the DTT device.
- If not defined, then U-Boot uses predefined value for
- specified DTT device.
-
CONFIG_SOFT_I2C_READ_REPEATED_START
defining this will force the i2c_read() function in
Specify the number of FPGA devices to support.
- CONFIG_CMD_FPGA_LOADMK
-
- Enable support for fpga loadmk command
-
- CONFIG_CMD_FPGA_LOADP
-
- Enable support for fpga loadp command - load partial bitstream
-
- CONFIG_CMD_FPGA_LOADBP
-
- Enable support for fpga loadbp command - load partial bitstream
- (Xilinx only)
-
CONFIG_SYS_FPGA_PROG_FEEDBACK
Enable printing of hash marks during FPGA configuration.
this is instead controlled by the value of
/config/load-environment.
-- Parallel Flash support:
- CONFIG_SYS_NO_FLASH
-
- Traditionally U-Boot was run on systems with parallel NOR
- flash. This option is used to disable support for parallel NOR
- flash. This option should be defined if the board does not have
- parallel flash.
-
- If this option is not defined one of the generic flash drivers
- (e.g. CONFIG_FLASH_CFI_DRIVER or CONFIG_ST_SMI) must be
- selected or the board must provide an implementation of the
- flash API (see include/flash.h).
-
- DataFlash Support:
CONFIG_HAS_DATAFLASH
A better solution is to properly configure the firewall,
but sometimes that is not allowed.
-- Hashing support:
- CONFIG_CMD_HASH
-
- This enables a generic 'hash' command which can produce
- hashes / digests from a few algorithms (e.g. SHA1, SHA256).
-
- CONFIG_HASH_VERIFY
-
- Enable the hash verify command (hash -v). This adds to code
- size a little.
-
- CONFIG_SHA1 - This option enables support of hashing using SHA1
- algorithm. The hash is calculated in software.
- CONFIG_SHA256 - This option enables support of hashing using
- SHA256 algorithm. The hash is calculated in software.
- CONFIG_SHA_HW_ACCEL - This option enables hardware acceleration
- for SHA1/SHA256 hashing.
- This affects the 'hash' command and also the
- hash_lookup_algo() function.
- CONFIG_SHA_PROG_HW_ACCEL - This option enables
- hardware-acceleration for SHA1/SHA256 progressive hashing.
- Data can be streamed in a block at a time and the hashing
- is performed in hardware.
-
- Note: There is also a sha1sum command, which should perhaps
- be deprecated in favour of 'hash sha1'.
-
-- Freescale i.MX specific commands:
- CONFIG_CMD_HDMIDETECT
- This enables 'hdmidet' command which returns true if an
- HDMI monitor is detected. This command is i.MX 6 specific.
-
- CONFIG_CMD_BMODE
- This enables the 'bmode' (bootmode) command for forcing
- a boot from specific media.
-
- This is useful for forcing the ROM's usb downloader to
- activate upon a watchdog reset which is nice when iterating
- on U-Boot. Using the reset button or running bmode normal
- will set it back to normal. This command currently
- supports i.MX53 and i.MX6.
-
- bootcount support:
CONFIG_BOOTCOUNT_LIMIT
CONFIG_AT91SAM9XE
enable special bootcounter support on at91sam9xe based boards.
- CONFIG_BLACKFIN
- enable special bootcounter support on blackfin based boards.
CONFIG_SOC_DA8XX
enable special bootcounter support on da850 based boards.
CONFIG_BOOTCOUNT_RAM
This define is introduced, as the legacy image format is
enabled per default for backward compatibility.
-- FIT image support:
- CONFIG_FIT_DISABLE_SHA256
- Supporting SHA256 hashes has quite an impact on binary size.
- For constrained systems sha256 hash support can be disabled
- with this option.
-
- and move it to Kconfig
-
- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
consider that a completely unreadable NAND block is bad,
and thus should be skipped silently.
- CONFIG_SPL_ABORT_ON_RAW_IMAGE
- When defined, SPL will proceed to another boot method
- if the image it has loaded does not have a signature.
-
CONFIG_SPL_RELOC_STACK
Adress of the start of the stack SPL will use after
relocation. If unspecified, this is equal to
If defined, don't allow the -f switch to env set override variable
access flags.
-- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
- This is set by OMAP boards for the max time that reset should
- be asserted. See doc/README.omap-reset-time for details on how
- the value can be calculated on a given board.
-
- CONFIG_USE_STDINT
If stdint.h is available with your toolchain you can define this
option to enable it. You can provide option 'USE_STDINT=1' when
If defined, the x86 reset vector code is included. This is not
needed when U-Boot is running from Coreboot.
-- CONFIG_SYS_MPUCLK
- Defines the MPU clock speed (in MHz).
-
- NOTE : currently only supported on AM335x platforms.
-
- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
Enables the RTC32K OSC on AM33xx based plattforms
average for all boards 752 bytes for the whole U-Boot image,
624 text + 127 data).
-On Blackfin, the normal C ABI (except for P3) is followed as documented here:
- http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
-
- ==> U-Boot will use P3 to hold a pointer to the global data
-
On ARM, the following registers are used:
R0: function argument word/integer result
projects / u-boot.git / blobdiff