cmd: Kconfig: Move CONFIG_MP to Kconfig

[u-boot.git] / include / configs / sbc8641d.h

diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index 7c8ceb30f2fd7c370a7259f0615c2c3b627fb08e..a620f0d2b468d7ee611e943363f253694a1e5cf9 100644 (file)
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2007 Wind River Systems <www.windriver.com>
  * Copyright 2007 Embedded Specialties, Inc.
@@ -6,8 +7,6 @@
  * Copyright 2006 Freescale Semiconductor.
  *
  * Srikanth Srinivasan ([email protected])
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -21,12 +20,8 @@
 #define __CONFIG_H
 
 /* High Level Configuration Options */
-#define CONFIG_SBC8641D                1       /* SBC8641D board specific */
-#define CONFIG_MP              1       /* support multiple processors */
 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
 
-#define        CONFIG_SYS_TEXT_BASE    0xfff00000
-
 #ifdef RUN_DIAG
 #define CONFIG_SYS_DIAG_ADDR        0xff800000
 #endif
@@ -46,9 +41,7 @@
 #define CONFIG_PCIE2           1       /* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT    1       /* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1   /* indirect PCI bridge support */
-#define CONFIG_FSL_LAW         1       /* Use common FSL init code */
 
-#define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_BAT_RW          1       /* Use common BAT rw code */
@@ -58,7 +51,6 @@
 #undef CONFIG_DDR_ECC                  /* only for ECC DDR module */
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER      /* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE          0xDeadBeef
-#define CONFIG_NUM_DDR_CONTROLLERS     2
 #define CACHE_LINE_INTERLEAVING                0x20000000
 #define PAGE_INTERLEAVING              0x21000000
 #define BANK_INTERLEAVING              0x22000000
@@ -77,8 +69,6 @@
 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_F      1       /* Call board_pre_init */
-
 #undef CONFIG_SYS_DRAM_TEST                            /* memory test, takes time */
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest region */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
@@ -104,7 +94,6 @@
 #define CONFIG_SYS_MAX_DDR_BAT_SIZE    0x80000000      /* BAT mapping size */
 #define CONFIG_VERY_BIG_RAM
 
-#define CONFIG_NUM_DDR_CONTROLLERS     2
 #define CONFIG_DIMM_SLOTS_PER_CTLR     2
 #define CONFIG_CHIP_SELECTS_PER_CTRL   (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
@@ -240,7 +229,6 @@
 #define CONFIG_SYS_MALLOC_LEN          (1024 * 1024)   /* Reserved for malloc */
 
 /* Serial Port */
-#define CONFIG_CONS_INDEX     1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -305,9 +293,6 @@
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
 
-#define CONFIG_DOS_PARTITION
-#undef CONFIG_SCSI_AHCI
-
 #ifdef CONFIG_SCSI_AHCI
 #define CONFIG_SATA_ULI5288
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID    4
@@ -449,7 +434,6 @@
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_FLASH 1
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128k(one sector) for env */
 #define CONFIG_ENV_SIZE                0x2000
@@ -457,30 +441,12 @@
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
 
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
-#endif
-
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
 
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP                    /* undef to save memory */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#define CONFIG_CMDLINE_EDITING 1               /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-    #define CONFIG_SYS_CBSIZE  1024            /* Console I/O Buffer Size */
-#else
-    #define CONFIG_SYS_CBSIZE  256             /* Console I/O Buffer Size */
-#endif
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS     16              /* max number of command args */
-#define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 
 /*
  * For booting Linux, the board info and command line data
@@ -511,7 +477,7 @@
 
 #define CONFIG_IPADDR          192.168.0.50
 
-#define CONFIG_HOSTNAME                sbc8641d
+#define CONFIG_HOSTNAME                "sbc8641d"
 #define CONFIG_ROOTPATH                "/opt/eldk/ppc_74xx"
 #define CONFIG_BOOTFILE                "uImage"
 
@@ -522,10 +488,6 @@
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR                1000000
 
-#undef  CONFIG_BOOTARGS                /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE        115200
-
 #define        CONFIG_EXTRA_ENV_SETTINGS                                       \
    "netdev=eth0\0"                                                     \
    "consoledev=ttyS0\0"                                                        \