#define __CONFIGS_MX28EVK_H__
/* System configurations */
-#define CONFIG_MX28 /* i.MX28 SoC */
#define CONFIG_MACH_TYPE MACH_TYPE_MX28EVK
-#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > "
-
-/* U-Boot Commands */
-#define CONFIG_SYS_NO_FLASH
-#include <config_cmd_default.h>
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_GPIO
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_SETEXPR
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NAND_TRIMFFS
-#define CONFIG_VIDEO
/* Memory configuration */
#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
/* Environment */
+#ifndef CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE (16 * 1024)
+#else
+#define CONFIG_ENV_SIZE (4 * 1024)
+#endif
#define CONFIG_ENV_OVERWRITE
/* Environment is in MMC */
/* Environemnt is in SPI flash */
#if defined(CONFIG_CMD_SF) && defined(CONFIG_ENV_IS_IN_SPI_FLASH)
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_ENV_SIZE 0x1000 /* 4KB */
#define CONFIG_ENV_OFFSET 0x40000 /* 256K */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SECT_SIZE 0x1000
/* UBI and NAND partitioning */
#ifdef CONFIG_CMD_NAND
-#define CONFIG_CMD_UBI
-#define CONFIG_CMD_UBIFS
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_RBTREE
-#define CONFIG_LZO
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
-#define MTDIDS_DEFAULT "nand0=gpmi-nand"
-#define MTDPARTS_DEFAULT \
- "mtdparts=gpmi-nand:" \
- "3m(bootloader)ro," \
- "512k(environment)," \
- "512k(redundant-environment)," \
- "4m(kernel)," \
- "128k(fdt)," \
- "8m(ramdisk)," \
- "-(filesystem)"
#endif
/* FEC Ethernet on SoC */
#ifdef CONFIG_CMD_NET
#define CONFIG_FEC_MXC
-#define CONFIG_NET_MULTI
+#define CONFIG_FEC_MXC_MDIO_BASE MXS_ENET0_BASE
#define CONFIG_MX28_FEC_MAC_IN_OCOTP
#endif
#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_MXS_PORT1
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
-#define CONFIG_USB_ETHER_SMSC95XX
#endif
/* SPI */
/* SPI Flash */
#ifdef CONFIG_CMD_SF
-#define CONFIG_SPI_FLASH
#define CONFIG_SF_DEFAULT_BUS 2
#define CONFIG_SF_DEFAULT_CS 0
/* this may vary and depends on the installed chip */
-#define CONFIG_SPI_FLASH_SST
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#define CONFIG_SF_DEFAULT_SPEED 24000000
#endif
#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_LOGO
#define CONFIG_SPLASH_SCREEN
-#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_GZIP
#endif
/* Boot Linux */
-#define CONFIG_BOOTDELAY 1
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_LOADADDR 0x42000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/* Extra Environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ubifs_file=filesystem.ubifs\0" \
"update_nand_full_filename=u-boot.nand\0" \
"update_nand_firmware_filename=u-boot.sb\0" \
- "update_sd_firmware_filename=u-boot.sd\0" \
"update_nand_firmware_maxsz=0x100000\0" \
"update_nand_stride=0x40\0" /* MX28 datasheet ch. 12.12 */ \
"update_nand_count=0x4\0" /* MX28 datasheet ch. 12.12 */ \
"nand info ; " \
"setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
"setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
- "update_nand_full=" /* Update FCB, DBBT and FW */ \
+ "update_nand_firmware_full=" /* Update FCB, DBBT and FW */ \
"if tftp ${update_nand_full_filename} ; then " \
"run update_nand_get_fcb_size ; " \
"nand scrub -y 0x0 ${filesize} ; " \
"nand write ${loadaddr} ${fcb_sz} ${filesize} ; " \
"nand write ${loadaddr} ${fw_off} ${filesize} ; " \
"fi\0" \
+ "update_nand_kernel=" /* Update kernel */ \
+ "mtdparts default; " \
+ "nand erase.part kernel; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "nand write ${loadaddr} kernel ${filesize}\0" \
+ "update_nand_fdt=" /* Update fdt */ \
+ "mtdparts default; " \
+ "nand erase.part fdt; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${fdt_file}; " \
+ "nand write ${loadaddr} fdt ${filesize}\0" \
+ "update_nand_filesystem=" /* Update filesystem */ \
+ "mtdparts default; " \
+ "nand erase.part filesystem; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${ubifs_file}; " \
+ "ubi part filesystem; " \
+ "ubi create filesystem; " \
+ "ubi write ${loadaddr} filesystem ${filesize}\0" \
+ "nandargs=setenv bootargs console=${console_mainline},${baudrate} " \
+ "rootfstype=ubifs ubi.mtd=6 root=ubi0_0 ${mtdparts}\0" \
+ "nandboot=" /* Boot from NAND */ \
+ "mtdparts default; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} kernel 0x00400000; " \
+ "if test ${boot_fdt} = yes; then " \
+ "nand read ${fdt_addr} fdt 0x00080000; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = no; then " \
+ "bootz; " \
+ "else " \
+ "echo \"ERROR: Set boot_fdt to yes or no.\"; " \
+ "fi; " \
+ "fi\0" \
+ "update_sd_firmware_filename=u-boot.sd\0" \
"update_sd_firmware=" /* Update the SD firmware partition */ \
"if mmc rescan ; then " \
"if tftp ${update_sd_firmware_filename} ; then " \
"fi ; " \
"fi\0" \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"console_fsl=ttyAM0\0" \
"console_mainline=ttyAMA0\0" \
"fdt_file=imx28-evk.dtb\0" \
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=${console_mainline},${baudrate} " \
"root=/dev/nfs " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi;" \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
projects / u-boot.git / blobdiff