powerpc: mpc8641hpcn: Enable DHCP command and DDR debug

[u-boot.git] / include / configs / sequoia.h

diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index b6a5e6a59c98cadc2abb045d0e64756c7d8b1953..7a120ed5a69e673478bbc644f94091aca5aec6ec 100644 (file)
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -45,7 +45,6 @@
  * Define this if you want support for video console with radeon 9200 pci card
  * Also set CONFIG_SYS_TEXT_BASE to 0xFFF80000 in board/amcc/sequoia/config.mk in this case
  */
-#undef CONFIG_VIDEO
 
 #ifdef CONFIG_VIDEO
 /*
@@ -55,7 +54,6 @@
 #define CONFIG_4xx_DCACHE              /* enable dcache                */
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_F 1    /* Call board_early_init_f      */
 #define CONFIG_MISC_INIT_R     1       /* Call misc_init_r             */
 
 /*
@@ -100,15 +98,6 @@
 #if defined(CONFIG_SYS_RAMBOOT)
 #define CONFIG_ENV_IS_NOWHERE          /* Store env in memory only     */
 #define CONFIG_ENV_SIZE                (8 << 10)
-/*
- * In RAM-booting version, we have no environment storage. So we need to
- * provide at least preliminary MAC addresses for the 4xx EMAC driver to
- * register the interfaces. Those two addresses are generated via the
- * tools/gen_eth_addr tool and should only be used in a closed laboratory
- * environment.
- */
-#define        CONFIG_ETHADDR          4a:56:49:22:3e:43
-#define        CONFIG_ETH1ADDR         02:93:53:d5:06:98
 #else
 #define CONFIG_ENV_IS_IN_FLASH         /* use FLASH for environ vars   */
 #endif
@@ -133,6 +122,7 @@
 
 #define CONFIG_SYS_FLASH_EMPTY_INFO          /* print 'E' for empty sector on flinfo */
 #define CONFIG_SYS_FLASH_QUIET_TEST    1       /* don't warn upon unknown flash      */
+#endif /* CONFIG_CMD_FLASH */
 
 #ifdef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* size of one complete sector        */
@@ -143,7 +133,6 @@
 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
 #endif
-#endif /* CONFIG_CMD_FLASH */
 
 /*
  * DDR SDRAM
@@ -160,7 +149,6 @@
  */
 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0          400000
 
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR     (0xa8>>1)
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
@@ -171,14 +159,6 @@
 #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET    0
 #define CONFIG_4xx_CONFIG_BLOCKSIZE            16
 
-/* I2C SYSMON (LM75, AD7414 is almost compatible)                      */
-#define CONFIG_DTT_LM75                1       /* ON Semi's LM75               */
-#define CONFIG_DTT_AD7414      1       /* use AD7414                   */
-#define CONFIG_DTT_SENSORS     {0}     /* Sensor addresses             */
-#define CONFIG_SYS_DTT_MAX_TEMP        70
-#define CONFIG_SYS_DTT_LOW_TEMP        -30
-#define CONFIG_SYS_DTT_HYSTERESIS      3
-
 /*
  * Default environment variables
  */
@@ -204,16 +184,13 @@
 
 /* USB */
 #ifdef CONFIG_440EPX
-
-#undef CONFIG_USB_EHCI /* OHCI by default */
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_USB_EHCI_PPC4XX
 #define CONFIG_SYS_PPC4XX_USB_ADDR     0xe0000300
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_EHCI_MMIO_BIG_ENDIAN
 #define CONFIG_EHCI_DESC_BIG_ENDIAN
-#else /* CONFIG_USB_EHCI */
+#else /* CONFIG_USB_EHCI_HCD */
 #define CONFIG_USB_OHCI_NEW
 #define CONFIG_SYS_OHCI_BE_CONTROLLER
 
@@ -224,29 +201,21 @@
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
 #endif
 
-#define CONFIG_USB_STORAGE
 /* Comment this out to enable USB 1.1 device */
 #define USB_2_0_DEVICE
 
 #endif /* CONFIG_440EPX */
 
 /* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
 
 /*
  * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_CMD_CHIP_CONFIG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_FAT
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SDRAM
 
 #ifdef CONFIG_440EPX
-#define CONFIG_CMD_USB
 #endif
 
 #ifndef CONFIG_RAINIER
@@ -279,17 +248,13 @@
 #define CONFIG_LOGBUFFER
 #define CONFIG_SYS_POST_CACHE_ADDR     0x7fff0000      /* free virtual address     */
 
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV   /* Otherwise it catches logbuffer as output */
-
 #define CONFIG_SUPPORT_VFAT
 
 /*
  * PCI stuff
  */
 /* General PCI */
-#define CONFIG_PCI                     /* include pci support          */
 #define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
-#define CONFIG_PCI_PNP                 /* do pci plug-and-play         */
 #define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0       /* to avoid problems with PNP   */
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup  */
 #define CONFIG_SYS_PCI_TARGBASE        0x80000000      /* PCIaddr mapped to    */
@@ -424,12 +389,8 @@
 #define CONFIG_ATI_RADEON_FB           /* use radeon framebuffer driver */
 #define VIDEO_IO_OFFSET                        0xe8000000
 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS         VIDEO_IO_OFFSET
-#define CONFIG_VIDEO_SW_CURSOR
 #define CONFIG_VIDEO_LOGO
-#define CONFIG_CFB_CONSOLE
 #define CONFIG_SPLASH_SCREEN
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_CMD_BMP
 #endif
 
 #endif /* __CONFIG_H */