[u-boot.git] / include / configs / advantech_dms-ba16.h

/*
 * Copyright (C) 2016 Timesys Corporation
 * Copyright (C) 2016 Advantech Corporation
 * Copyright (C) 2012 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __ADVANTECH_DMSBA16_CONFIG_H
#define __ADVANTECH_DMSBA16_CONFIG_H

#include <asm/arch/imx-regs.h>
#include <asm/imx-common/gpio.h>

#define CONFIG_BOARD_NAME	"Advantech DMS-BA16"
#define CONFIG_DEFAULT_FDT_FILE	"imx6q-dms-ba16.dtb"

#define CONFIG_MXC_UART_BASE	UART4_BASE
#define CONFIG_CONSOLE_DEV	"ttymxc3"
#define CONFIG_EXTRA_BOOTARGS	"panic=10"

#define CONFIG_BOOT_DIR	""
#define CONFIG_LOADCMD "fatload"
#define CONFIG_RFSPART "2"

#define CONFIG_SUPPORT_EMMC_BOOT

#include "mx6_common.h"
#include <linux/sizes.h>

#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT

#define CONFIG_MXC_GPIO
#define CONFIG_MXC_UART

#define CONFIG_CMD_FUSE
#define CONFIG_MXC_OCOTP

/* SATA Configs */
#define CONFIG_CMD_SATA
#define CONFIG_DWC_AHSATA
#define CONFIG_SYS_SATA_MAX_DEVICE	1
#define CONFIG_DWC_AHSATA_PORT_ID	0
#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
#define CONFIG_LIBATA

/* MMC Configs */
#define CONFIG_FSL_ESDHC
#define CONFIG_FSL_USDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR      0
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_BOUNCE_BUFFER
#define CONFIG_DOS_PARTITION

/* USB Configs */
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS	0
#define CONFIG_USB_KEYBOARD
#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP

#define CONFIG_USBD_HS
#define CONFIG_USB_FUNCTION_MASS_STORAGE
#define CONFIG_USB_GADGET_VBUS_DRAW 2

/* Networking Configs */
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE			ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE		RGMII
#define CONFIG_ETHPRIME		"FEC"
#define CONFIG_FEC_MXC_PHYADDR		4
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS

/* Serial Flash */
#ifdef CONFIG_CMD_SF
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS		0
#define CONFIG_SF_DEFAULT_CS		0
#define CONFIG_SF_DEFAULT_SPEED	20000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
#endif

/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX	1
#define CONFIG_BAUDRATE	115200

/* Command definition */
#define CONFIG_CMD_BMODE

#define CONFIG_LOADADDR	0x12000000
#define CONFIG_SYS_TEXT_BASE	0x17800000

#define CONFIG_EXTRA_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=" CONFIG_BOOT_DIR "/uImage\0" \
	"uboot=u-boot.imx\0" \
	"fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \
	"fdt_addr=0x18000000\0" \
	"boot_fdt=yes\0" \
	"ip_dyn=yes\0" \
	"console=" CONFIG_CONSOLE_DEV "\0" \
	"fdt_high=0xffffffff\0"	  \
	"initrd_high=0xffffffff\0" \
	"sddev=0\0" \
	"emmcdev=1\0" \
	"partnum=1\0" \
	"loadcmd=" CONFIG_LOADCMD "\0" \
	"rfspart=" CONFIG_RFSPART "\0" \
	"update_sd_firmware=" \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"if mmc dev ${mmcdev}; then "	\
			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
				"setexpr fw_sz ${filesize} / 0x200; " \
				"setexpr fw_sz ${fw_sz} + 1; "	\
				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
			"fi; "	\
		"fi\0" \
	"update_sf_uboot=" \
		"if tftp $loadaddr $uboot; then " \
			"sf probe; " \
			"sf erase 0 0xC0000; " \
			"sf write $loadaddr 0x400 $filesize; " \
			"echo 'U-Boot upgraded. Please reset'; " \
		"fi\0" \
	"setargs=setenv bootargs console=${console},${baudrate} " \
		"root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \
	"loadbootscript=" \
		"${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
		" source\0" \
	"loadimage=" \
		"${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
	"loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
	"tryboot=" \
		"if run loadbootscript; then " \
			"run bootscript; " \
		"else " \
			"if run loadimage; then " \
				"run doboot; " \
			"fi; " \
		"fi;\0" \
	"doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
		"run setargs; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if run loadfdt; then " \
				"bootm ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"if test ${boot_fdt} = try; then " \
					"bootm; " \
				"else " \
					"echo WARN: Cannot load the DT; " \
				"fi; " \
			"fi; " \
		"else " \
			"bootm; " \
		"fi;\0" \
	"netargs=setenv bootargs console=${console},${baudrate} " \
		"root=/dev/nfs " \
		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
		"run netargs; " \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${image}; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
				"bootm ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"if test ${boot_fdt} = try; then " \
					"bootm; " \
				"else " \
					"echo WARN: Cannot load the DT; " \
				"fi; " \
			"fi; " \
		"else " \
			"bootm; " \
		"fi;\0" \

#define CONFIG_BOOTCOMMAND \
	"usb start; " \
	"setenv dev usb; " \
	"setenv devnum 0; " \
	"setenv rootdev sda${rfspart}; " \
	"run tryboot; " \
	\
	"setenv dev mmc; " \
	"setenv rootdev mmcblk0p${rfspart}; " \
	\
	"setenv devnum ${sddev}; " \
	"if mmc dev ${devnum}; then " \
		"run tryboot; " \
	"fi; " \
	\
	"setenv devnum ${emmcdev}; " \
	"setenv rootdev mmcblk${emmcdev}p${rfspart}; " \
	"if mmc dev ${devnum}; then " \
		"run tryboot; " \
	"fi; " \
	\
	"bmode usb; " \

#define CONFIG_ARP_TIMEOUT     200UL

/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP
#define CONFIG_AUTO_COMPLETE

/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

#define CONFIG_SYS_MEMTEST_START       0x10000000
#define CONFIG_SYS_MEMTEST_END         0x10010000
#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000

#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR

#define CONFIG_CMDLINE_EDITING
#define CONFIG_STACKSIZE               (128 * 1024)

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS           1
#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH

#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE                 (8 * 1024)
#define CONFIG_ENV_OFFSET               (768 * 1024)
#define CONFIG_ENV_SECT_SIZE            (64 * 1024)
#define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED

#ifndef CONFIG_SYS_DCACHE_OFF
#endif

#define CONFIG_SYS_FSL_USDHC_NUM        3

/* Framebuffer */
#define CONFIG_VIDEO_IPUV3
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IPUV3_CLK                260000000
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP

#define CONFIG_PWM_IMX
#define CONFIG_IMX6_PWM_PER_CLK         66000000

#undef CONFIG_CMD_PCI
#ifdef CONFIG_CMD_PCI
#define CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIE_IMX
#define CONFIG_PCIE_IMX_PERST_GPIO      IMX_GPIO_NR(7, 12)
#define CONFIG_PCIE_IMX_POWER_GPIO      IMX_GPIO_NR(1, 5)
#endif

/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_SPEED            100000
#define CONFIG_SYS_I2C_MXC_I2C1
#define CONFIG_SYS_I2C_MXC_I2C2
#define CONFIG_SYS_I2C_MXC_I2C3

#endif	/* __ADVANTECH_DMSBA16_CONFIG_H */
Commit	Line	Data
ff383220 AB	1	/*
	2	* Copyright (C) 2016 Timesys Corporation
	3	* Copyright (C) 2016 Advantech Corporation
	4	* Copyright (C) 2012 Freescale Semiconductor, Inc.
	5	*
	6	* SPDX-License-Identifier: GPL-2.0+
	7	*/
	8
	9	#ifndef __ADVANTECH_DMSBA16_CONFIG_H
	10	#define __ADVANTECH_DMSBA16_CONFIG_H
	11
	12	#include <asm/arch/imx-regs.h>
	13	#include <asm/imx-common/gpio.h>
	14
	15	#define CONFIG_BOARD_NAME "Advantech DMS-BA16"
	16	#define CONFIG_DEFAULT_FDT_FILE "imx6q-dms-ba16.dtb"
	17
	18	#define CONFIG_MXC_UART_BASE UART4_BASE
	19	#define CONFIG_CONSOLE_DEV "ttymxc3"
	20	#define CONFIG_EXTRA_BOOTARGS "panic=10"
	21
	22	#define CONFIG_BOOT_DIR ""
	23	#define CONFIG_LOADCMD "fatload"
	24	#define CONFIG_RFSPART "2"
	25
	26	#define CONFIG_SUPPORT_EMMC_BOOT
	27
	28	#include "mx6_common.h"
	29	#include <linux/sizes.h>
	30
ff383220 AB	31	#define CONFIG_CMDLINE_TAG
	32	#define CONFIG_SETUP_MEMORY_TAGS
	33	#define CONFIG_INITRD_TAG
	34	#define CONFIG_REVISION_TAG
	35	#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
	36
	37	#define CONFIG_BOARD_EARLY_INIT_F
	38	#define CONFIG_BOARD_LATE_INIT
	39
	40	#define CONFIG_MXC_GPIO
	41	#define CONFIG_MXC_UART
	42
	43	#define CONFIG_CMD_FUSE
	44	#define CONFIG_MXC_OCOTP
	45
	46	/* SATA Configs */
	47	#define CONFIG_CMD_SATA
	48	#define CONFIG_DWC_AHSATA
	49	#define CONFIG_SYS_SATA_MAX_DEVICE 1
	50	#define CONFIG_DWC_AHSATA_PORT_ID 0
	51	#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
	52	#define CONFIG_LBA48
	53	#define CONFIG_LIBATA
	54
	55	/* MMC Configs */
	56	#define CONFIG_FSL_ESDHC
	57	#define CONFIG_FSL_USDHC
	58	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
	59	#define CONFIG_MMC
	60	#define CONFIG_GENERIC_MMC
	61	#define CONFIG_BOUNCE_BUFFER
	62	#define CONFIG_DOS_PARTITION
	63
	64	/* USB Configs */
	65	#define CONFIG_USB_EHCI
	66	#define CONFIG_USB_EHCI_MX6
	67	#define CONFIG_USB_STORAGE
	68	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
	69	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	70	#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI \| PORT_PTS_PTW)
	71	#define CONFIG_MXC_USB_FLAGS 0
	72	#define CONFIG_USB_KEYBOARD
	73	#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
	74
	75	#define CONFIG_USBD_HS
	76	#define CONFIG_USB_FUNCTION_MASS_STORAGE
	77	#define CONFIG_USB_GADGET_VBUS_DRAW 2
	78
	79	/* Networking Configs */
	80	#define CONFIG_FEC_MXC
	81	#define CONFIG_MII
	82	#define IMX_FEC_BASE ENET_BASE_ADDR
	83	#define CONFIG_FEC_XCV_TYPE RGMII
	84	#define CONFIG_ETHPRIME "FEC"
	85	#define CONFIG_FEC_MXC_PHYADDR 4
	86	#define CONFIG_PHYLIB
	87	#define CONFIG_PHY_ATHEROS
	88
	89	/* Serial Flash */
	90	#ifdef CONFIG_CMD_SF
	91	#define CONFIG_MXC_SPI
	92	#define CONFIG_SF_DEFAULT_BUS 0
	93	#define CONFIG_SF_DEFAULT_CS 0
	94	#define CONFIG_SF_DEFAULT_SPEED 20000000
95	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
96	#endif
97
98	/* allow to overwrite serial and ethaddr */
99	#define CONFIG_ENV_OVERWRITE
100	#define CONFIG_CONS_INDEX 1
101	#define CONFIG_BAUDRATE 115200
102
103	/* Command definition */
104	#define CONFIG_CMD_BMODE
105
106	#define CONFIG_LOADADDR 0x12000000
107	#define CONFIG_SYS_TEXT_BASE 0x17800000
108
109	#define CONFIG_EXTRA_ENV_SETTINGS \
110	"script=boot.scr\0" \
111	"image=" CONFIG_BOOT_DIR "/uImage\0" \
112	"uboot=u-boot.imx\0" \
113	"fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \
114	"fdt_addr=0x18000000\0" \
115	"boot_fdt=yes\0" \
116	"ip_dyn=yes\0" \
117	"console=" CONFIG_CONSOLE_DEV "\0" \
118	"fdt_high=0xffffffff\0" \
119	"initrd_high=0xffffffff\0" \
120	"sddev=0\0" \
121	"emmcdev=1\0" \
122	"partnum=1\0" \
123	"loadcmd=" CONFIG_LOADCMD "\0" \
124	"rfspart=" CONFIG_RFSPART "\0" \
125	"update_sd_firmware=" \
126	"if test ${ip_dyn} = yes; then " \
127	"setenv get_cmd dhcp; " \
128	"else " \
129	"setenv get_cmd tftp; " \
130	"fi; " \
131	"if mmc dev ${mmcdev}; then " \
132	"if ${get_cmd} ${update_sd_firmware_filename}; then " \
133	"setexpr fw_sz ${filesize} / 0x200; " \
134	"setexpr fw_sz ${fw_sz} + 1; " \
135	"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
136	"fi; " \
137	"fi\0" \
138	"update_sf_uboot=" \
139	"if tftp $loadaddr $uboot; then " \
140	"sf probe; " \
141	"sf erase 0 0xC0000; " \
142	"sf write $loadaddr 0x400 $filesize; " \
143	"echo 'U-Boot upgraded. Please reset'; " \
144	"fi\0" \
145	"setargs=setenv bootargs console=${console},${baudrate} " \
146	"root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \
147	"loadbootscript=" \
148	"${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
149	"bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
150	" source\0" \
151	"loadimage=" \
152	"${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
153	"loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
154	"tryboot=" \
155	"if run loadbootscript; then " \
156	"run bootscript; " \
157	"else " \
158	"if run loadimage; then " \
159	"run doboot; " \
160	"fi; " \
161	"fi;\0" \
162	"doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
163	"run setargs; " \
164	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
165	"if run loadfdt; then " \
166	"bootm ${loadaddr} - ${fdt_addr}; " \
167	"else " \
168	"if test ${boot_fdt} = try; then " \
169	"bootm; " \
170	"else " \
171	"echo WARN: Cannot load the DT; " \
172	"fi; " \
173	"fi; " \
174	"else " \
175	"bootm; " \
176	"fi;\0" \
177	"netargs=setenv bootargs console=${console},${baudrate} " \
178	"root=/dev/nfs " \
179	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
180	"netboot=echo Booting from net ...; " \
181	"run netargs; " \
182	"if test ${ip_dyn} = yes; then " \
183	"setenv get_cmd dhcp; " \
184	"else " \
185	"setenv get_cmd tftp; " \
186	"fi; " \
187	"${get_cmd} ${image}; " \
188	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
189	"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
190	"bootm ${loadaddr} - ${fdt_addr}; " \
191	"else " \
192	"if test ${boot_fdt} = try; then " \
193	"bootm; " \
194	"else " \
195	"echo WARN: Cannot load the DT; " \
196	"fi; " \
197	"fi; " \
198	"else " \
199	"bootm; " \
200	"fi;\0" \
201
202	#define CONFIG_BOOTCOMMAND \
203	"usb start; " \
204	"setenv dev usb; " \
205	"setenv devnum 0; " \
206	"setenv rootdev sda${rfspart}; " \
207	"run tryboot; " \
208	\
209	"setenv dev mmc; " \
210	"setenv rootdev mmcblk0p${rfspart}; " \
211	\
212	"setenv devnum ${sddev}; " \
213	"if mmc dev ${devnum}; then " \
214	"run tryboot; " \
215	"fi; " \
216	\
217	"setenv devnum ${emmcdev}; " \
218	"setenv rootdev mmcblk${emmcdev}p${rfspart}; " \
219	"if mmc dev ${devnum}; then " \
220	"run tryboot; " \
221	"fi; " \
222	\
223	"bmode usb; " \
224
225	#define CONFIG_ARP_TIMEOUT 200UL
226
227	/* Miscellaneous configurable options */
228	#define CONFIG_SYS_LONGHELP
229	#define CONFIG_AUTO_COMPLETE
230
231	/* Print Buffer Size */
232	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
233	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
234
235	#define CONFIG_SYS_MEMTEST_START 0x10000000
236	#define CONFIG_SYS_MEMTEST_END 0x10010000
237	#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
238
239	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
240
241	#define CONFIG_CMDLINE_EDITING
242	#define CONFIG_STACKSIZE (128 * 1024)
243
244	/* Physical Memory Map */
245	#define CONFIG_NR_DRAM_BANKS 1
246	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
247
248	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
249	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
250	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
251
252	#define CONFIG_SYS_INIT_SP_OFFSET \
253	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
254	#define CONFIG_SYS_INIT_SP_ADDR \
255	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
256
257	/* FLASH and environment organization */
258	#define CONFIG_SYS_NO_FLASH
259
260	#define CONFIG_ENV_IS_IN_SPI_FLASH
261	#define CONFIG_ENV_SIZE (8 * 1024)
262	#define CONFIG_ENV_OFFSET (768 * 1024)
263	#define CONFIG_ENV_SECT_SIZE (64 * 1024)
264	#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
265	#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
266	#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
267	#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
268
269	#ifndef CONFIG_SYS_DCACHE_OFF
270	#endif
271
272	#define CONFIG_SYS_FSL_USDHC_NUM 3
273
274	/* Framebuffer */
ff383220 AB	275	#define CONFIG_VIDEO_IPUV3
	276	#define CONFIG_CFB_CONSOLE
	277	#define CONFIG_VGA_AS_SINGLE_DEVICE
ff383220 AB	278	#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
	279	#define CONFIG_VIDEO_BMP_RLE8
	280	#define CONFIG_SPLASH_SCREEN
	281	#define CONFIG_SPLASH_SCREEN_ALIGN
	282	#define CONFIG_BMP_16BPP
	283	#define CONFIG_VIDEO_LOGO
	284	#define CONFIG_VIDEO_BMP_LOGO
	285	#define CONFIG_IPUV3_CLK 260000000
	286	#define CONFIG_IMX_HDMI
	287	#define CONFIG_IMX_VIDEO_SKIP
	288
	289	#define CONFIG_PWM_IMX
	290	#define CONFIG_IMX6_PWM_PER_CLK 66000000
	291
	292	#undef CONFIG_CMD_PCI
	293	#ifdef CONFIG_CMD_PCI
	294	#define CONFIG_PCI
	295	#define CONFIG_PCI_PNP
	296	#define CONFIG_PCI_SCAN_SHOW
	297	#define CONFIG_PCIE_IMX
	298	#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
	299	#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5)
	300	#endif
	301
	302	/* I2C Configs */
	303	#define CONFIG_SYS_I2C
	304	#define CONFIG_SYS_I2C_MXC
	305	#define CONFIG_SYS_I2C_SPEED 100000
	306	#define CONFIG_SYS_I2C_MXC_I2C1
	307	#define CONFIG_SYS_I2C_MXC_I2C2
	308	#define CONFIG_SYS_I2C_MXC_I2C3
	309
	310	#endif /* __ADVANTECH_DMSBA16_CONFIG_H */