[u-boot.git] / include / configs / TQM862M.h

/*
 * (C) Copyright 2000-2014
 * Wolfgang Denk, DENX Software Engineering, [email protected].
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_MPC860		1
#define CONFIG_MPC860T		1
#define CONFIG_MPC862		1

#define CONFIG_TQM862M		1	/* ...on a TQM8xxM module	*/

#define	CONFIG_SYS_TEXT_BASE	0x40000000

#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
#define CONFIG_SYS_SMC_RXBUFLEN	128
#define CONFIG_SYS_MAXIDLE	10
#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/

#define	CONFIG_BOOTCOUNT_LIMIT


#define CONFIG_BOARD_TYPES	1	/* support board types		*/

#define CONFIG_PREBOOT	"echo;"	\
	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
	"echo"

#undef	CONFIG_BOOTARGS

#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"netdev=eth0\0"							\
	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off panic=1\0"			\
	"flash_nfs=run nfsargs addip;"					\
		"bootm ${kernel_addr}\0"				\
	"flash_self=run ramargs addip;"					\
		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
	"rootpath=/opt/eldk/ppc_8xx\0"					\
	"hostname=TQM862M\0"						\
	"bootfile=TQM862M/uImage\0"					\
	"fdt_addr=40080000\0"						\
	"kernel_addr=400A0000\0"					\
	"ramdisk_addr=40280000\0"					\
	"u-boot=TQM862M/u-image.bin\0"					\
	"load=tftp 200000 ${u-boot}\0"					\
	"update=prot off 40000000 +${filesize};"			\
		"era 40000000 +${filesize};"				\
		"cp.b 200000 40000000 ${filesize};"			\
		"sete filesize;save\0"					\
	""
#define CONFIG_BOOTCOMMAND	"run flash_self"

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/

#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/

#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE

#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION

#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/

/*
 * Command line configuration.
 */
#define CONFIG_CMD_DATE
#define CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2

#define CONFIG_NETCONSOLE

/*
 * Miscellaneous configurable options
 */
#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/

#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/

#if defined(CONFIG_CMD_KGDB)
#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
#else
#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
#endif
#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */
/*-----------------------------------------------------------------------
 * Internal Memory Mapped Register
 */
#define CONFIG_SYS_IMMR		0xFFF00000

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define	CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_FLASH_BASE		0x40000000
#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/

/*-----------------------------------------------------------------------
 * FLASH organization
 */

/* use CFI flash driver */
#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */

#define	CONFIG_ENV_IS_IN_FLASH	1
#define	CONFIG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
#define	CONFIG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
#define	CONFIG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */

#define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */

/*-----------------------------------------------------------------------
 * Dynamic MTD partition support
 */
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"

#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
						"128k(dtb),"		\
						"1920k(kernel),"	\
						"5632(rootfs),"		\
						"4m(data)"

/*-----------------------------------------------------------------------
 * Hardware Information Block
 */
#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
#endif

/*-----------------------------------------------------------------------
 * SYPCR - System Protection Control				11-9
 * SYPCR can only be written once after reset!
 *-----------------------------------------------------------------------
 * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 */
#if defined(CONFIG_WATCHDOG)
#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
#else
#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif

/*-----------------------------------------------------------------------
 * SIUMCR - SIU Module Configuration				11-6
 *-----------------------------------------------------------------------
 * PCMCIA config., multi-function pin tri-state
 */
#ifndef	CONFIG_CAN_DRIVER
#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
#else	/* we must activate GPL5 in the SIUMCR for CAN */
#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
#endif	/* CONFIG_CAN_DRIVER */

/*-----------------------------------------------------------------------
 * TBSCR - Time Base Status and Control				11-26
 *-----------------------------------------------------------------------
 * Clear Reference Interrupt Status, Timebase freezing enabled
 */
#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)

/*-----------------------------------------------------------------------
 * RTCSC - Real-Time Clock Status and Control Register		11-27
 *-----------------------------------------------------------------------
 */
#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)

/*-----------------------------------------------------------------------
 * PISCR - Periodic Interrupt Status and Control		11-31
 *-----------------------------------------------------------------------
 * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 */
#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)

/*-----------------------------------------------------------------------
 * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
 *-----------------------------------------------------------------------
 * Reset PLL lock status sticky bit, timer expired status bit and timer
 * interrupt status bit
 */
#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)

/*-----------------------------------------------------------------------
 * SCCR - System Clock and reset Control Register		15-27
 *-----------------------------------------------------------------------
 * Set clock output, timebase and RTC source and divider,
 * power management and some other internal clocks
 */
#define SCCR_MASK	SCCR_EBDF11
#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
			 SCCR_DFALCD00)

/*-----------------------------------------------------------------------
 * PCMCIA stuff
 *-----------------------------------------------------------------------
 *
 */
#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )

/*-----------------------------------------------------------------------
 * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
 *-----------------------------------------------------------------------
 */

#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/

#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/

#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/

#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000

#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR

/* Offset for data I/O			*/
#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)

/* Offset for normal register accesses	*/
#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)

/* Offset for alternate registers	*/
#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100

/*-----------------------------------------------------------------------
 *
 *-----------------------------------------------------------------------
 *
 */
#define CONFIG_SYS_DER	0

/*
 * Init Memory Controller:
 *
 * BR0/1 and OR0/1 (FLASH)
 */

#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #1	*/

/* used to re-map FLASH both when starting from SRAM or FLASH:
 * restrict access enough to keep SRAM working (if any)
 * but not too much to meddle with FLASH accesses
 */
#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */

/*
 * FLASH timing:
 */
#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
				 OR_SCY_3_CLK | OR_EHTR | OR_BI)

#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )

#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )

/*
 * BR2/3 and OR2/3 (SDRAM)
 *
 */
#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/

/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00

#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )

#ifndef	CONFIG_CAN_DRIVER
#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
					BR_PS_8 | BR_MS_UPMB | BR_V )
#endif	/* CONFIG_CAN_DRIVER */

/*
 * Memory Periodic Timer Prescaler
 *
 * The Divider for PTA (refresh timer) configuration is based on an
 * example SDRAM configuration (64 MBit, one bank). The adjustment to
 * the number of chip selects (NCS) and the actually needed refresh
 * rate is done by setting MPTPR.
 *
 * PTA is calculated from
 *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
 *
 *	gclk	  CPU clock (not bus clock!)
 *	Trefresh  Refresh cycle * 4 (four word bursts used)
 *
 * 4096  Rows from SDRAM example configuration
 * 1000  factor s -> ms
 *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
 *    4  Number of refresh cycles per period
 *   64  Refresh cycle in ms per number of rows
 * --------------------------------------------
 * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
 *
 *  50 MHz =>  50.000.000 / Divider =  98
 *  66 Mhz =>  66.000.000 / Divider = 129
 *  80 Mhz =>  80.000.000 / Divider = 156
 * 100 Mhz => 100.000.000 / Divider = 195
 */

#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
#define CONFIG_SYS_MAMR_PTA	98

/*
 * For 16 MBit, refresh rates could be 31.3 us
 * (= 64 ms / 2K = 125 / quad bursts).
 * For a simpler initialization, 15.6 us is used instead.
 *
 * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
 * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
 */
#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/

/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/

/*
 * MAMR settings for SDRAM
 */

/* 8 column SDRAM */
#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
/* 9 column SDRAM */
#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)

#define CONFIG_SCC1_ENET
#define CONFIG_FEC_ENET
#define CONFIG_ETHPRIME		"SCC"

#define CONFIG_HWCONFIG		1

#endif	/* __CONFIG_H */
Commit	Line	Data
71f95118	1	/*
23c5d253	2	* (C) Copyright 2000-2014
71f95118 WD	3	* Wolfgang Denk, DENX Software Engineering, [email protected].
71f95118 WD	4	*
1a459660	5	* SPDX-License-Identifier: GPL-2.0+
71f95118 WD	6	*/
	7
	8	/*
	9	* board/config.h - configuration options, board specific
	10	*/
	11
	12	#ifndef __CONFIG_H
	13	#define __CONFIG_H
	14
	15	/*
	16	* High Level Configuration Options
	17	* (easy to change)
	18	*/
	19
	20	#define CONFIG_MPC860 1
	21	#define CONFIG_MPC860T 1
	22	#define CONFIG_MPC862 1
	23
	24	#define CONFIG_TQM862M 1 /* ...on a TQM8xxM module */
	25
2ae18241 WD	26	#define CONFIG_SYS_TEXT_BASE 0x40000000
2ae18241 WD	27
71f95118	28	#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
3cb7a480 WD	29	#define CONFIG_SYS_SMC_RXBUFLEN 128
3cb7a480 WD	30	#define CONFIG_SYS_MAXIDLE 10
71f95118 WD	31	#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
71f95118 WD	32
ae3af05e	33	#define CONFIG_BOOTCOUNT_LIMIT
71f95118	34
71f95118 WD	35
	36	#define CONFIG_BOARD_TYPES 1 /* support board types */
	37
	38	#define CONFIG_PREBOOT "echo;" \
32bf3d14	39	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
71f95118 WD	40	"echo"
	41
	42	#undef CONFIG_BOOTARGS
	43
	44	#define CONFIG_EXTRA_ENV_SETTINGS \
	45	"netdev=eth0\0" \
	46	"nfsargs=setenv bootargs root=/dev/nfs rw " \
fe126d8b	47	"nfsroot=${serverip}:${rootpath}\0" \
71f95118	48	"ramargs=setenv bootargs root=/dev/ram rw\0" \
fe126d8b WD	49	"addip=setenv bootargs ${bootargs} " \
	50	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	51	":${hostname}:${netdev}:off panic=1\0" \
71f95118	52	"flash_nfs=run nfsargs addip;" \
fe126d8b	53	"bootm ${kernel_addr}\0" \
71f95118	54	"flash_self=run ramargs addip;" \
fe126d8b WD	55	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
fe126d8b WD	56	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
71f95118	57	"rootpath=/opt/eldk/ppc_8xx\0" \
29f8f58f WD	58	"hostname=TQM862M\0" \
29f8f58f WD	59	"bootfile=TQM862M/uImage\0" \
eb6da805 WD	60	"fdt_addr=40080000\0" \
	61	"kernel_addr=400A0000\0" \
	62	"ramdisk_addr=40280000\0" \
29f8f58f WD	63	"u-boot=TQM862M/u-image.bin\0" \
	64	"load=tftp 200000 ${u-boot}\0" \
	65	"update=prot off 40000000 +${filesize};" \
	66	"era 40000000 +${filesize};" \
	67	"cp.b 200000 40000000 ${filesize};" \
	68	"sete filesize;save\0" \
71f95118 WD	69	""
	70	#define CONFIG_BOOTCOMMAND "run flash_self"
	71
	72	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
6d0f6bcf	73	#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
71f95118 WD	74
	75	#undef CONFIG_WATCHDOG /* watchdog disabled */
	76
	77	#define CONFIG_STATUS_LED 1 /* Status LED enabled */
	78
	79	#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
	80
37d4bb70 JL	81	/*
	82	* BOOTP options
	83	*/
	84	#define CONFIG_BOOTP_SUBNETMASK
	85	#define CONFIG_BOOTP_GATEWAY
	86	#define CONFIG_BOOTP_HOSTNAME
	87	#define CONFIG_BOOTP_BOOTPATH
	88	#define CONFIG_BOOTP_BOOTFILESIZE
	89
71f95118 WD	90	#define CONFIG_MAC_PARTITION
	91	#define CONFIG_DOS_PARTITION
	92
	93	#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
	94
2694690e JL	95	/*
	96	* Command line configuration.
	97	*/
2694690e	98	#define CONFIG_CMD_DATE
2694690e	99	#define CONFIG_CMD_IDE
29f8f58f	100	#define CONFIG_CMD_JFFS2
71f95118	101
29f8f58f WD	102	#define CONFIG_NETCONSOLE
29f8f58f WD	103
71f95118 WD	104	/*
	105	* Miscellaneous configurable options
	106	*/
6d0f6bcf	107	#define CONFIG_SYS_LONGHELP /* undef to save memory */
71f95118	108
2751a95a	109	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
71f95118	110
2694690e	111	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	112	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
71f95118	113	#else
6d0f6bcf	114	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
71f95118	115	#endif
6d0f6bcf JCPV	116	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	117	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	118	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
71f95118	119
6d0f6bcf JCPV	120	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
6d0f6bcf JCPV	121	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
71f95118	122
6d0f6bcf	123	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
71f95118	124
71f95118 WD	125	/*
	126	* Low Level Configuration Settings
	127	* (address mappings, register initial values, etc.)
	128	* You should know what you are doing if you make changes here.
	129	*/
	130	/*-----------------------------------------------------------------------
	131	* Internal Memory Mapped Register
	132	*/
6d0f6bcf	133	#define CONFIG_SYS_IMMR 0xFFF00000
71f95118 WD	134
	135	/*-----------------------------------------------------------------------
	136	* Definitions for initial stack pointer and data area (in DPRAM)
	137	*/
6d0f6bcf	138	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
553f0982	139	#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
25ddd1fb	140	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	141	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
71f95118 WD	142
	143	/*-----------------------------------------------------------------------
	144	* Start addresses for the final memory configuration
	145	* (Set up by the startup code)
6d0f6bcf	146	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
71f95118	147	*/
6d0f6bcf JCPV	148	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	149	#define CONFIG_SYS_FLASH_BASE 0x40000000
	150	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	151	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	152	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
71f95118 WD	153
	154	/*
	155	* For booting Linux, the board info and command line data
	156	* have to be in the first 8 MB of memory, since this is
	157	* the maximum mapped by the Linux kernel during initialization.
	158	*/
6d0f6bcf	159	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
71f95118 WD	160
	161	/*-----------------------------------------------------------------------
	162	* FLASH organization
	163	*/
71f95118	164
e318d9e9	165	/* use CFI flash driver */
6d0f6bcf	166	#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
00b1883a	167	#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
6d0f6bcf JCPV	168	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
	169	#define CONFIG_SYS_FLASH_EMPTY_INFO
	170	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
	171	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	172	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
71f95118	173
5a1aceb0	174	#define CONFIG_ENV_IS_IN_FLASH 1
0e8d1586 JCPV	175	#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
	176	#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment */
	177	#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
71f95118 WD	178
71f95118 WD	179	/* Address and size of Redundant Environment Sector */
0e8d1586 JCPV	180	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
0e8d1586 JCPV	181	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
71f95118	182
6d0f6bcf	183	#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
67c31036	184
7c803be2 WD	185	#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
7c803be2 WD	186
29f8f58f WD	187	/*-----------------------------------------------------------------------
	188	* Dynamic MTD partition support
	189	*/
68d7d651	190	#define CONFIG_CMD_MTDPARTS
942556a9 SR	191	#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
942556a9 SR	192	#define CONFIG_FLASH_CFI_MTD
29f8f58f WD	193	#define MTDIDS_DEFAULT "nor0=TQM8xxM-0"
	194
	195	#define MTDPARTS_DEFAULT "mtdparts=TQM8xxM-0:512k(u-boot)," \
	196	"128k(dtb)," \
	197	"1920k(kernel)," \
	198	"5632(rootfs)," \
cd82919e	199	"4m(data)"
29f8f58f	200
71f95118 WD	201	/*-----------------------------------------------------------------------
	202	* Hardware Information Block
	203	*/
6d0f6bcf JCPV	204	#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
	205	#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
	206	#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
71f95118 WD	207
	208	/*-----------------------------------------------------------------------
	209	* Cache Configuration
	210	*/
6d0f6bcf	211	#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
2694690e	212	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	213	#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
71f95118 WD	214	#endif
	215
	216	/*-----------------------------------------------------------------------
	217	* SYPCR - System Protection Control 11-9
	218	* SYPCR can only be written once after reset!
	219	*-----------------------------------------------------------------------
	220	* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
	221	*/
	222	#if defined(CONFIG_WATCHDOG)
6d0f6bcf	223	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| \
71f95118 WD	224	SYPCR_SWE \| SYPCR_SWRI\| SYPCR_SWP)
71f95118 WD	225	#else
6d0f6bcf	226	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| SYPCR_SWP)
71f95118 WD	227	#endif
	228
	229	/*-----------------------------------------------------------------------
	230	* SIUMCR - SIU Module Configuration 11-6
	231	*-----------------------------------------------------------------------
	232	* PCMCIA config., multi-function pin tri-state
	233	*/
	234	#ifndef CONFIG_CAN_DRIVER
6d0f6bcf	235	#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 \| SIUMCR_DBPC00 \| SIUMCR_MLRC01)
71f95118	236	#else /* we must activate GPL5 in the SIUMCR for CAN */
6d0f6bcf	237	#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 \| SIUMCR_DBPC00 \| SIUMCR_MLRC01)
71f95118 WD	238	#endif /* CONFIG_CAN_DRIVER */
	239
	240	/*-----------------------------------------------------------------------
	241	* TBSCR - Time Base Status and Control 11-26
	242	*-----------------------------------------------------------------------
	243	* Clear Reference Interrupt Status, Timebase freezing enabled
	244	*/
6d0f6bcf	245	#define CONFIG_SYS_TBSCR (TBSCR_REFA \| TBSCR_REFB \| TBSCR_TBF)
71f95118 WD	246
	247	/*-----------------------------------------------------------------------
	248	* RTCSC - Real-Time Clock Status and Control Register 11-27
	249	*-----------------------------------------------------------------------
	250	*/
6d0f6bcf	251	#define CONFIG_SYS_RTCSC (RTCSC_SEC \| RTCSC_ALR \| RTCSC_RTF\| RTCSC_RTE)
71f95118 WD	252
	253	/*-----------------------------------------------------------------------
	254	* PISCR - Periodic Interrupt Status and Control 11-31
	255	*-----------------------------------------------------------------------
	256	* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
	257	*/
6d0f6bcf	258	#define CONFIG_SYS_PISCR (PISCR_PS \| PISCR_PITF)
71f95118 WD	259
	260	/*-----------------------------------------------------------------------
	261	* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
	262	*-----------------------------------------------------------------------
	263	* Reset PLL lock status sticky bit, timer expired status bit and timer
	264	* interrupt status bit
71f95118	265	*/
6d0f6bcf	266	#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS \| PLPRCR_TEXPS \| PLPRCR_TMIST)
71f95118 WD	267
	268	/*-----------------------------------------------------------------------
	269	* SCCR - System Clock and reset Control Register 15-27
	270	*-----------------------------------------------------------------------
	271	* Set clock output, timebase and RTC source and divider,
	272	* power management and some other internal clocks
	273	*/
	274	#define SCCR_MASK SCCR_EBDF11
6d0f6bcf	275	#define CONFIG_SYS_SCCR (SCCR_COM00 \| SCCR_DFSYNC00 \| SCCR_DFBRG00 \| \
71f95118 WD	276	SCCR_DFNL000 \| SCCR_DFNH000 \| SCCR_DFLCD000 \| \
71f95118 WD	277	SCCR_DFALCD00)
71f95118 WD	278
	279	/*-----------------------------------------------------------------------
	280	* PCMCIA stuff
	281	*-----------------------------------------------------------------------
	282	*
	283	*/
6d0f6bcf JCPV	284	#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
	285	#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
	286	#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
	287	#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
	288	#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
	289	#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
	290	#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
	291	#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
71f95118 WD	292
	293	/*-----------------------------------------------------------------------
	294	* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
	295	*-----------------------------------------------------------------------
	296	*/
	297
8d1165e1	298	#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
71f95118 WD	299	#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
	300
	301	#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
	302	#undef CONFIG_IDE_LED /* LED for ide not supported */
	303	#undef CONFIG_IDE_RESET /* reset for ide not supported */
	304
6d0f6bcf JCPV	305	#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
6d0f6bcf JCPV	306	#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
71f95118	307
6d0f6bcf	308	#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
71f95118	309
6d0f6bcf	310	#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
71f95118 WD	311
71f95118 WD	312	/* Offset for data I/O */
6d0f6bcf	313	#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
71f95118 WD	314
71f95118 WD	315	/* Offset for normal register accesses */
6d0f6bcf	316	#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
71f95118 WD	317
71f95118 WD	318	/* Offset for alternate registers */
6d0f6bcf	319	#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
71f95118 WD	320
	321	/*-----------------------------------------------------------------------
	322	*
	323	*-----------------------------------------------------------------------
	324	*
	325	*/
6d0f6bcf	326	#define CONFIG_SYS_DER 0
71f95118 WD	327
	328	/*
	329	* Init Memory Controller:
	330	*
	331	* BR0/1 and OR0/1 (FLASH)
	332	*/
	333
	334	#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
	335	#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #1 */
	336
	337	/* used to re-map FLASH both when starting from SRAM or FLASH:
	338	* restrict access enough to keep SRAM working (if any)
	339	* but not too much to meddle with FLASH accesses
	340	*/
6d0f6bcf JCPV	341	#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
6d0f6bcf JCPV	342	#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
71f95118 WD	343
	344	/*
	345	* FLASH timing:
	346	*/
6d0f6bcf	347	#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 \| OR_TRLX \| OR_CSNT_SAM \| \
71f95118	348	OR_SCY_3_CLK \| OR_EHTR \| OR_BI)
71f95118	349
6d0f6bcf JCPV	350	#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
	351	#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
	352	#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) \| BR_V )
71f95118	353
6d0f6bcf JCPV	354	#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
	355	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
	356	#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) \| BR_V )
71f95118 WD	357
	358	/*
	359	* BR2/3 and OR2/3 (SDRAM)
	360	*
	361	*/
	362	#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
	363	#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
	364	#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
	365
	366	/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
6d0f6bcf	367	#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
71f95118	368
6d0f6bcf JCPV	369	#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM \| CONFIG_SYS_OR_TIMING_SDRAM )
6d0f6bcf JCPV	370	#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) \| BR_MS_UPMA \| BR_V )
71f95118 WD	371
71f95118 WD	372	#ifndef CONFIG_CAN_DRIVER
6d0f6bcf JCPV	373	#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
6d0f6bcf JCPV	374	#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) \| BR_MS_UPMA \| BR_V )
71f95118	375	#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
6d0f6bcf JCPV	376	#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
	377	#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
	378	#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM \| OR_G5LA \| OR_BI)
	379	#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) \| \
71f95118 WD	380	BR_PS_8 \| BR_MS_UPMB \| BR_V )
	381	#endif /* CONFIG_CAN_DRIVER */
	382
	383	/*
	384	* Memory Periodic Timer Prescaler
	385	*
	386	* The Divider for PTA (refresh timer) configuration is based on an
	387	* example SDRAM configuration (64 MBit, one bank). The adjustment to
	388	* the number of chip selects (NCS) and the actually needed refresh
	389	* rate is done by setting MPTPR.
	390	*
	391	* PTA is calculated from
	392	* PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
	393	*
	394	* gclk CPU clock (not bus clock!)
	395	* Trefresh Refresh cycle * 4 (four word bursts used)
	396	*
	397	* 4096 Rows from SDRAM example configuration
	398	* 1000 factor s -> ms
	399	* 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
	400	* 4 Number of refresh cycles per period
	401	* 64 Refresh cycle in ms per number of rows
	402	* --------------------------------------------
	403	* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
	404	*
	405	* 50 MHz => 50.000.000 / Divider = 98
	406	* 66 Mhz => 66.000.000 / Divider = 129
	407	* 80 Mhz => 80.000.000 / Divider = 156
	408	* 100 Mhz => 100.000.000 / Divider = 195
	409	*/
e9132ea9	410
6d0f6bcf JCPV	411	#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
6d0f6bcf JCPV	412	#define CONFIG_SYS_MAMR_PTA 98
71f95118 WD	413
	414	/*
	415	* For 16 MBit, refresh rates could be 31.3 us
	416	* (= 64 ms / 2K = 125 / quad bursts).
	417	* For a simpler initialization, 15.6 us is used instead.
	418	*
6d0f6bcf JCPV	419	* #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
6d0f6bcf JCPV	420	* #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
71f95118	421	*/
6d0f6bcf JCPV	422	#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
6d0f6bcf JCPV	423	#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
71f95118 WD	424
71f95118 WD	425	/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
6d0f6bcf JCPV	426	#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
6d0f6bcf JCPV	427	#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
71f95118 WD	428
	429	/*
	430	* MAMR settings for SDRAM
	431	*/
	432
	433	/* 8 column SDRAM */
6d0f6bcf	434	#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
71f95118 WD	435	MAMR_AMA_TYPE_0 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A11 \| \
	436	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)
	437	/* 9 column SDRAM */
6d0f6bcf	438	#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
71f95118 WD	439	MAMR_AMA_TYPE_1 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A10 \| \
	440	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)
	441
71f95118 WD	442	#define CONFIG_SCC1_ENET
71f95118 WD	443	#define CONFIG_FEC_ENET
48690d80	444	#define CONFIG_ETHPRIME "SCC"
71f95118	445
7026ead0 HS	446	#define CONFIG_HWCONFIG 1
7026ead0 HS	447
71f95118	448	#endif /* __CONFIG_H */