qcow2: Catch !*host_offset for data allocation

qcow2_alloc_cluster_offset() uses host_offset == 0 as "no preferred
offset" for the (data) cluster range to be allocated. However, this
offset is actually valid and may be allocated on images with a corrupted
refcount table or first refcount block.

In this case, the corruption prevention should normally catch that
write anyway (because it would overwrite the image header). But since 0
is a special value here, the function assumes that nothing has been
allocated at all which it asserts against.

Because this condition is not qemu's fault but rather that of a broken
image, it shouldn't throw an assertion but rather mark the image corrupt
and show an appropriate message, which this patch does by calling the
corruption check earlier than it would be called normally (before the
assertion).

Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

qcow2: Return useful error code in refcount_init()

If bdrv_pread() returns an error, it is very unlikely that it was
ENOMEM. In this case, the return value should be passed along; as
bdrv_pread() will always either return the number of bytes read or a
negative value (the error code), the condition for checking whether
bdrv_pread() failed can be simplified (and clarified) as well.

Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

mirror: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the mirror block job.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

vpc: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the vpc block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

vmdk: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the vmdk block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

vhdx: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the vhdx block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

vdi: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the vdi block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

rbd: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the rbd block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>

raw-win32: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the raw-win32 block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>

raw-posix: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the raw-posix block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>

qed: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the qed block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

qcow2: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the qcow2 block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>

qcow1: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the qcow1 block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>

parallels: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the parallels block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

nfs: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the nfs block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

iscsi: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the iscsi block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Eric Blake <eblake@redhat.com>

dmg: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the dmg block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

curl: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the curl block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

cloop: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the cloop block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

bochs: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses the allocations in the bochs block driver.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

block: Handle failure for potentially large allocations

Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.

This patch addresses bounce buffer allocations in block.c. While at it,
convert bdrv_commit() from plain g_malloc() to qemu_try_blockalign().

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>

block: Introduce qemu_try_blockalign()

This function returns NULL instead of aborting when an allocation fails.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>

block: iotest - update 084 to test static VDI image creation

This updates the VDI corruption test to also test static VDI image
creation, as well as the default dynamic image creation.

Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

block: vpc - use block layer ops in vpc_create, instead of posix calls

Use the block layer to create, and write to, the image file in the VPC
.bdrv_create() operation.

This has a couple of benefits: Images can now be created over protocols,
and hacks such as NOCOW are not needed in the image format driver, and
the underlying file protocol appropriate for the host OS can be relied
upon.

Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

block: use the standard 'ret' instead of 'result'

Most QEMU code uses 'ret' for function return values. The VDI driver
uses a mix of 'result' and 'ret'.  This cleans that up, switching over
to the standard 'ret' usage.

Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

block: vdi - use block layer ops in vdi_create, instead of posix calls

Use the block layer to create, and write to, the image file in the
VDI .bdrv_create() operation.

This has a couple of benefits: Images can now be created over protocols,
and hacks such as NOCOW are not needed in the image format driver, and
the underlying file protocol appropriate for the host OS can be relied
upon.

Also some minor cleanup for error handling.

Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

block: allow bdrv_unref() to be passed NULL pointers

If bdrv_unref() is passed a NULL BDS pointer, it is safe to
exit with no operation.  This will allow cleanup code to blindly
call bdrv_unref() on a BDS that has been initialized to NULL.

Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

test-coroutine: add baseline test that times the cost of function calls

This can be used to compute the cost of coroutine operations.  In the
end the cost of the function call is a few clock cycles, so it's pretty
cheap for now, but it may become more relevant as the coroutine code
is optimized.

For example, here are the results on my machine:

   Function call 100000000 iterations: 0.173884 s
   Yield 100000000 iterations: 8.445064 s
   Lifecycle 1000000 iterations: 0.098445 s
   Nesting 10000 iterations of 1000 depth each: 7.406431 s

One yield takes 83 nanoseconds, one enter takes 97 nanoseconds,
one coroutine allocation takes (roughly, since some of the allocations
in the nesting test do hit the pool) 739 nanoseconds:

   (8.445064 - 0.173884) * 10^9 / 100000000 = 82.7
   (0.098445 * 100 - 0.173884) * 10^9 / 100000000 = 96.7
   (7.406431 * 10 - 0.173884) * 10^9 / 100000000 = 738.9

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

block: VHDX endian fixes

This patch contains several changes for endian conversion fixes for
VHDX, particularly for big-endian machines (multibyte values in VHDX are
all on disk in LE format).

Tests were done with existing qemu-iotests on an IBM POWER7 (8406-71Y).
This includes sample images created by Hyper-V, both with dirty logs and
without.

In addition, VHDX image files created (and written to) on a BE machine
were tested on a LE machine, and vice-versa.

Reported-by: Markus Armburster <armbru@redhat.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

block: vhdx - add error check

This add an error check for an invalid descriptor entry signature,
when flushing the log descriptor entries.

Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

thread-pool: avoid deadlock in nested aio_poll() calls

The thread pool has a race condition if two elements complete before
thread_pool_completion_bh() runs:

  If element A's callback waits for element B using aio_poll() it will
  deadlock since pool->completion_bh is not marked scheduled when the
  nested aio_poll() runs.

Fix this by marking the BH scheduled while thread_pool_completion_bh()
is executing.  This way any nested aio_poll() loops will enter
thread_pool_completion_bh() and complete the remaining elements.

Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

thread-pool: avoid per-thread-pool EventNotifier

EventNotifier is implemented using an eventfd or pipe.  It therefore
consumes file descriptors, which can be limited by rlimits and should
therefore be used sparingly.

Switch from EventNotifier to QEMUBH in thread-pool.c.  Originally
EventNotifier was used because qemu_bh_schedule() was not thread-safe
yet.

Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block: bump coroutine pool size for drives

When a BlockDriverState is associated with a storage controller
DeviceState we expect guest I/O.  Use this opportunity to bump the
coroutine pool size by 64.

This patch ensures that the coroutine pool size scales with the number
of drives attached to the guest.  It should increase coroutine pool
usage (which makes qemu_coroutine_create() fast) without hogging too
much memory when fewer drives are attached.

Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>

coroutine: make pool size dynamic

Allow coroutine users to adjust the pool size.  For example, if the
guest has multiple emulated disk drives we should keep around more
coroutines.

Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>

qemu-iotests: add support for Archipelago protocol

Signed-off-by: Chrysostomos Nanakos <cnanakos@grnet.gr>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

QMP: Add support for Archipelago

Introduce new enum BlockdevOptionsArchipelago.

@volume:              #Name of the Archipelago volume image

@mport:               #'mport' is the port number on which mapperd is
                      listening. This is optional and if not specified,
                      QEMU will make Archipelago to use the default port.

@vport:               #'vport' is the port number on which vlmcd is
                      listening. This is optional and if not specified,
                      QEMU will make Archipelago to use the default port.

@segment:             #optional The name of the shared memory segment
                      Archipelago stack is using. This is optional
                      and if not specified, QEMU will make Archipelago
                      use the default value, 'archipelago'.

Signed-off-by: Chrysostomos Nanakos <cnanakos@grnet.gr>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block/archipelago: Add support for creating images

qemu-img archipelago:<volumename>[/mport=<mapperd_port>[:vport=<vlmcd_port>]
 [:segment=<segment_name>]] [size]

Signed-off-by: Chrysostomos Nanakos <cnanakos@grnet.gr>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block/archipelago: Implement bdrv_parse_filename()

VM Image on Archipelago volume can also be specified like this:

file=archipelago:<volumename>[/mport=<mapperd_port>[:vport=<vlmcd_port>][:
segment=<segment_name>]]

Examples:

file=archipelago:my_vm_volume
file=archipelago:my_vm_volume/mport=123
file=archipelago:my_vm_volume/mport=123:vport=1234
file=archipelago:my_vm_volume/mport=123:vport=1234:segment=my_segment

Signed-off-by: Chrysostomos Nanakos <cnanakos@grnet.gr>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block: Support Archipelago as a QEMU block backend

VM Image on Archipelago volume is specified like this:

file.driver=archipelago,file.volume=<volumename>[,file.mport=<mapperd_port>[,
file.vport=<vlmcd_port>][,file.segment=<segment_name>]]

'archipelago' is the protocol.

'mport' is the port number on which mapperd is listening. This is optional
and if not specified, QEMU will make Archipelago to use the default port.

'vport' is the port number on which vlmcd is listening. This is optional
and if not specified, QEMU will make Archipelago to use the default port.

'segment' is the name of the shared memory segment Archipelago stack is using.
This is optional and if not specified, QEMU will make Archipelago to use the
default value, 'archipelago'.

Examples:

file.driver=archipelago,file.volume=my_vm_volume
file.driver=archipelago,file.volume=my_vm_volume,file.mport=123
file.driver=archipelago,file.volume=my_vm_volume,file.mport=123,
file.vport=1234
file.driver=archipelago,file.volume=my_vm_volume,file.mport=123,
file.vport=1234,file.segment=my_segment

Signed-off-by: Chrysostomos Nanakos <cnanakos@grnet.gr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

qemu-img info: show nocow info

Add nocow info in 'qemu-img info' output to show whether the file
currently has NOCOW flag set or not.

Signed-off-by: Chunyan Liu <cyliu@suse.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

vmdk: Optimize cluster allocation

This drops the unnecessary bdrv_truncate() from, and also improves,
cluster allocation code path.

Before, when we need a new cluster, get_cluster_offset truncates the
image to bdrv_getlength() + cluster_size, and returns the offset of
added area, i.e. the image length before truncating.

This is not efficient, so it's now rewritten as:

  - Save the extent file length when opening.

  - When allocating cluster, use the saved length as cluster offset.

  - Don't truncate image, because we'll anyway write data there: just
    write any data at the EOF position, in descending priority:

    * New user data (cluster allocation happens in a write request).

    * Filling data in the beginning and/or ending of the new cluster, if
      not covered by user data: either backing file content (COW), or
      zero for standalone images.

One major benifit of this change is, on host mounted NFS images, even
over a fast network, ftruncate is slow (see the example below). This
change significantly speeds up cluster allocation. Comparing by
converting a cirros image (296M) to VMDK on an NFS mount point, over
1Gbe LAN:

    $ time qemu-img convert cirros-0.3.1.img /mnt/a.raw -O vmdk

    Before:
        real    0m21.796s
        user    0m0.130s
        sys     0m0.483s

    After:
        real    0m2.017s
        user    0m0.047s
        sys     0m0.190s

We also get rid of unchecked bdrv_getlength() and bdrv_truncate(), and
get a little more documentation in function comments.

Tested that this passes qemu-iotests for all VMDK subformats.

Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

qemu-iotests: Add data pattern in version3 VMDK sample image in 059

It's possible that we diverge from the specification with our
implementation.  Having a reference image in the test cases may detect
such problems when we introduce a bug that can read what it creates, but
can't handle a real VMDK.

Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

qdev-monitor: include QOM properties in -device FOO, help output

Update -device FOO,help to include QOM properties in addition to qdev
properties.  Devices are gradually adding more QOM properties that are
not reflected as qdev properties.

It is important to report all device properties since management tools
like libvirt use this information (and device-list-properties QMP) to
detect the presence of QEMU features.

This patch reuses the device-list-properties QMP machinery to avoid code
duplication.

Reported-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Cole Robinson <crobinso@redhat.com>

qmp: hide "hotplugged" device property from device-list-properties

The "hotplugged" device property was not reported before commit
f4eb32b590bf58c1c67570775eb78beb09964fad ("qmp: show QOM properties in
device-list-properties").  Fix this difference.

Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>

docs/multiple-iothreads.txt: add documentation on IOThread programming

This document explains how IOThreads and the main loop are related,
especially how to write code that can run in an IOThread.  Currently
only virtio-blk-data-plane uses these techniques.  The next obvious
target is virtio-scsi; there has also been work on virtio-net.

Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>

xen_disk:  fix possible null-ptr dereference

Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

configure: explicitly state version requirements to devel packages

Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

docs: Make the recommendation for the backing file name position a requirement

The current version of the qcow2 specification recommends to save the backing
file name in the end of the first cluster. It follows that the backing file
name can be saved somewhere in the image, but the first cluster, which
contradicts the current QEMU implementation.

The patch makes the backing file name required to be placed after the header
extensions in the first image cluster.

Signed-off-by: Maria Kustova <maria.k@catit.be>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>

block: Avoid bdrv_get_geometry() where errors should be detected

bdrv_get_geometry() hides errors.  Use bdrv_nb_sectors() or
bdrv_getlength() instead where that's obviously inappropriate.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

qemu-img: Make img_convert() get image size just once per image

Chiefly so I don't have to do the error checking in quadruplicate in
the next commit.  Moreover, replacing the frequently updated
bs_sectors by an array assigned just once makes the code easier to
understand.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block: Drop superfluous aligning of bdrv_getlength()'s value

It returns a multiple of the sector size.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block: Use bdrv_nb_sectors() where sectors, not bytes are wanted

Instead of bdrv_getlength().

Aside: a few of these callers don't handle errors.  I didn't
investigate whether they should.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block: Use bdrv_nb_sectors() in img_convert()

Instead of bdrv_getlength().  Replace variable output_length by
output_sectors.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block: Use bdrv_nb_sectors() in bdrv_co_get_block_status()

Instead of bdrv_getlength().

Replace variables length, length2 by total_sectors, nb_sectors2.
Bonus: use total_sectors instead of the slightly unclean
bs->total_sectors.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block: Use bdrv_nb_sectors() in bdrv_aligned_preadv()

Instead of bdrv_getlength().  Eliminate variable len.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block: Use bdrv_nb_sectors() in bdrv_make_zero()

Instead of bdrv_getlength().

Variable target_size is initially in bytes, then changes meaning to
sectors.  Ugh.  Replace by target_sectors.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block: New bdrv_nb_sectors()

A call to retrieve the image size converts between bytes and sectors
several times:

* BlockDriver method bdrv_getlength() returns bytes.

* refresh_total_sectors() converts to sectors, rounding up, and stores
  in total_sectors.

* bdrv_getlength() converts total_sectors back to bytes (now rounded
  up to a multiple of the sector size).

* Callers wanting sectors rather bytes convert it right back.
  Example: bdrv_get_geometry().

bdrv_nb_sectors() provides a way to omit the last two conversions.
It's exactly bdrv_getlength() with the conversion to bytes omitted.
It's functionally like bdrv_get_geometry() without its odd error
handling.

Reimplement bdrv_getlength() and bdrv_get_geometry() on top of
bdrv_nb_sectors().

The next patches will convert some users of bdrv_getlength() to
bdrv_nb_sectors().

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20140804' into staging

target-arm queue:
 * Set PC correctly when loading AArch64 ELF files
 * sdhci: Fix ADMA dma_memory_read access
 * some more foundational work for EL2/EL3 support
 * fix bugs which reveal themselves if the TARGET_PAGE_SIZE
   is not set to 1K

# gpg: Signature made Mon 04 Aug 2014 14:51:34 BST using RSA key ID 14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"

* remotes/pmaydell/tags/pull-target-arm-20140804:
  target-arm: A64: fix TLB flush instructions
  target-arm: don't hardcode mask values in arm_cpu_handle_mmu_fault
  target-arm: Fix bit test in sp_el0_access
  target-arm: Add FAR_EL2 and 3
  target-arm: Add ESR_EL2 and 3
  target-arm: Make far_el1 an array
  target-arm: A64: Respect SPSEL when taking exceptions
  target-arm: A64: Respect SPSEL in ERET SP restore
  target-arm: A64: Break out aarch64_save/restore_sp
  sd: sdhci: Fix ADMA dma_memory_read access
  hw/arm/virt: formatting: memory map
  hw/arm/boot: Set PC correctly when loading AArch64 ELF files

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm: A64: fix TLB flush instructions

According to the ARM ARM we weren't correctly flushing the TLB entries
where bits 63:56 didn't match bit 55 of the virtual address. This
exposed a problem when we switched QEMU's internal TARGET_PAGE_BITS to
12 for aarch64.

Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1406733627-24255-3-git-send-email-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm: don't hardcode mask values in arm_cpu_handle_mmu_fault

Otherwise we break quickly when we change TARGET_PAGE_SIZE.

Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1406733627-24255-2-git-send-email-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm: Fix bit test in sp_el0_access

Static code analyzers complain about a dubious & operation used for a
boolean value. The code does not test the PSTATE_SP bit as it should.

Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1406359601-25583-1-git-send-email-sw@weilnetz.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm: Add FAR_EL2 and 3

Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1402994746-8328-7-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm: Add ESR_EL2 and 3

Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1402994746-8328-6-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm: Make far_el1 an array

No functional change.
Prepares for future additions of the EL2 and 3 versions of this reg.

Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1402994746-8328-5-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm: A64: Respect SPSEL when taking exceptions

Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1402994746-8328-4-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm: A64: Respect SPSEL in ERET SP restore

Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1402994746-8328-3-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm: A64: Break out aarch64_save/restore_sp

Break out code to save/restore AArch64 SP into functions.

Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1402994746-8328-2-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

sd: sdhci: Fix ADMA dma_memory_read access

This dma_memory_read was giving too big a size when begin was non-zero.
This could cause segfaults in some circumstances. Fix.

Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/virt: formatting: memory map

Add some spacing and zeros to make it easier to read and
modify the map. This patch has no functional changes. The
review looks ugly, but it's actually pretty easy to confirm
all the addresses are as they should be - thanks to the new
formatting ;-)

Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/boot: Set PC correctly when loading AArch64 ELF files

The code in do_cpu_reset() correctly handled AArch64 CPUs
when running Linux kernels, but was missing code in the
branch of the if() that deals with loading ELF files.
Correctly jump to the ELF entry point on reset rather than
leaving the reset PC at zero.

Reported-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Christopher Covington <cov@codeaurora.org>
Cc: qemu-stable@nongnu.org

Merge remote-tracking branch 'remotes/amit-migration/for-2.2' into staging

* remotes/amit-migration/for-2.2:
  checker: ignore fields marked unused
  vmstate static checker: whitelist additions

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

Merge remote-tracking branch 'remotes/amit-virtio-rng/for-2.2' into staging

* remotes/amit-virtio-rng/for-2.2:
  virtio-rng: replace error_set calls with error_setg
  virtio-rng: Move error-checking forward to prevent memory leak

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

Merge remote-tracking branch 'remotes/sstabellini/xen-20140801' into staging

* remotes/sstabellini/xen-20140801:
  qemu: support xen hvm direct kernel boot
  tap-bsd: implement a FreeBSD only version of tap_open
  xen: fix usage of ENODATA

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

checker: ignore fields marked unused

While comparing qemu-1.0 json output with qemu-2.1, a few fields got
marked unused.  These need to be skipped over, and not flagged as
mismatches.

For handling unused fields, the exact number of bytes need to be skipped
over as the size of the unused field.

Currently, only the term "unused" is matched.  When more field names
turn up, this will have to be updated based on the whitelist matching
method to match more such terms.

Signed-off-by: Amit Shah <amit.shah@redhat.com>

virtio-rng: replace error_set calls with error_setg

Under recommendation from Luiz Capitulino, we are changing
the error_set calls to error_setg while we are fixing up
the error handling pathways of virtio-rng.

Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>

virtio-rng: Move error-checking forward to prevent memory leak

This patch pushes the error-checking forward and the virtio
initialization backward in the device realization function
in order to prevent memory leaks for hot plug scenarios.

Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>

Open 2.2 development tree

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

qemu: support xen hvm direct kernel boot

qemu side patch to support xen HVM direct kernel boot:
if -kernel exists, calls xen_load_linux(), which will read kernel/initrd
and add a linuxboot.bin or multiboot.bin option rom. The
linuxboot.bin/multiboot.bin will load kernel/initrd and jump to execute
kernel directly. It's working when xen uses seabios.

During this work, found the 'kvmvapic' is in option_rom list, it should
not be there in xen case. Set s->vapic_control = 0 in xen_apic_realize()
to handle that.

Signed-off-by: Chunyan Liu <cyliu@suse.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>

tap-bsd: implement a FreeBSD only version of tap_open

The current behaviour of tap_open for BSD systems differ greatly from
it's Linux counterpart. Since FreeBSD supports interface renaming and
tap device cloning by opening /dev/tap, implement a FreeBSD specific
version of tap_open that behaves like it's Linux counterpart.

This is specially important for toolstacks that use Qemu (like Xen
libxl), in order to have a unified behaviour across suported
platforms.

Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>

xen: fix usage of ENODATA

ENODATA doesn't exist on FreeBSD, so ENODATA errors returned by the
hypervisor are translated to ENOENT.

Also, the error code is returned in errno if the call returns -1, so
compare the error code with the value in errno instead of the value
returned by the function.

Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: xen-devel@lists.xenproject.org
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Anthony Perard <anthony.perard@citrix.com>

Update version for v2.1.0 release

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

Update version for v2.1.0-rc5 release

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/virt: fix pl031 addr typo

pl031's base address should be 0x9010000, not 0x90010000, otherwise
it sits in ram when configuring a guest with greater than 1G.

Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

Update version for v2.1.0-rc4 release

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

po: update Italian translation

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

po: Update French translation

Add new translations for recently added messages.

Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging

pc migration fixes

Last minute fixes for migration.
It seems that if we don't fix it now, fixing
it in the next version will be even more painful ...

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 29 Jul 2014 11:45:18 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg:                 aka "Michael S. Tsirkin <mst@redhat.com>"

* remotes/mst/tags/for_upstream:
  piix: set legacy table size for 1.7
  acpi-build: tweak acpi migration limits
  pc: future-proof migration-compatibility of ACPI tables
  acpi-build: minor code cleanup
  pc: acpi: generate AML only for PCI0 devices if PCI bridge hotplug is disabled
  bios-tables-test: fix ASL normalization false positive
  pc: hack for migration compatibility from QEMU 2.0
  acpi-dsdt: procedurally generate _PRT

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

piix: set legacy table size for 1.7

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

acpi-build: tweak acpi migration limits

- Tweak error message for legacy machine type:
  Basically if table size exceeds the limits we set all
  bets are off for migration: e.g. it can start failing even
  within given qemu minor version simply because of a bugfix.
- Increase table size to 128k.
- Make sure we notice it long before we start getting close to the
  128k limit: warn at 64k.
- Don't fail if we exceed the limit: most people don't care about
  migration, even less people care about cross version miration.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>

pc: future-proof migration-compatibility of ACPI tables

This patch avoids that similar changes break QEMU again in the future.
QEMU will now hard-code 64k as the maximum ACPI table size, which
(despite being an order of magnitude smaller than 640k) should be enough
for everyone.

Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

acpi-build: minor code cleanup

Fix up and add  comments to clarify code, plus a trivial
code change for clarity.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

pc: acpi: generate AML only for PCI0 devices if PCI bridge hotplug is disabled

Fixes migration regression from QEMU-1.7 to a newer QEMUs.
SSDT table size in QEMU-1.7 doesn't change regardless of
a number of PCI bridge devices present at startup.

However in QEMU-2.0 since addition of hotplug on PCI bridges,
each PCI bridge adds ~1875 bytes to SSDT table, including
pc-i440fx-1.7 machine type where PCI bridge hotplug disabled
via compat property.
It breaks migration from "QEMU-1.7" to "QEMU-2.[01] -M pc-i440fx-1.7"
since RAMBlock size of ACPI tables on target becomes larger
then on source and migration fails with:

"Length mismatch: /rom@etc/acpi/tables: 2000 in != 3000"

error.

Fix this by generating AML only for PCI0 bus if
hotplug on PCI bridges is disabled and preserves PCI brigde
description in AML as it was done in QEMU-1.7 for pc-i440fx-1.7.

It will help to maintain size of SSDT static regardless of
number of PCI bridges on startup for pc-i440fx-1.7 machine type.

Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

bios-tables-test: fix ASL normalization false positive

My version of IASL (from RHEL7) puts two newlines between the head comment
and the DefinitionBlock property.  Kill all newlines after the comment,
so that normalize_asl works properly.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>

po: Update German translation

Line numbers changed, and some translations were missing after commit
3d914488aee3dc1bf495e461aedf8fb4e5bb2270.

Update also "Show Tabs" to a more common translation, and remove some
old unused lines at the end.

Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>

target-mips/translate.c: Free TCG in OPC_DINSV

Free t0 and t1 in opcode OPC_DINSV.

Signed-off-by: Dongxue Zhang <elta.era@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>

pc: hack for migration compatibility from QEMU 2.0

Changing the ACPI table size causes migration to break, and the memory
hotplug work opened our eyes on how horribly we were breaking things in
2.0 already.

The ACPI table size is rounded to the next 4k, which one would think
gives some headroom.  In practice this is not the case, because the user
can control the ACPI table size (each CPU adds 97 bytes to the SSDT and
8 to the MADT) and so some "-smp" values will break the 4k boundary and
fail to migrate.  Similarly, PCI bridges add ~1870 bytes to the SSDT.

This patch concerns itself with fixing migration from QEMU 2.0.  It
computes the payload size of QEMU 2.0 and always uses that one.
The previous patch shrunk the ACPI tables enough that the QEMU 2.0 size
should always be enough; non-AML tables can change depending on the
configuration (especially MADT, SRAT, HPET) but they remain the same
between QEMU 2.0 and 2.1, so we only compute our padding based on the
sizes of the SSDT and DSDT.

Migration from QEMU 1.7 should work for guests that have a number of CPUs
other than 12, 13, 14, 54, 55, 56, 97, 98, 139, 140.  It was already
broken from QEMU 1.7 to QEMU 2.0 in the same way, though.

Even with this patch, QEMU 1.7 and 2.0 have two different ideas of
"-M pc-i440fx-2.0" when there are PCI bridges.  Igor sent a patch to
adopt the QEMU 1.7 definition.  I think distributions should apply
it if they move directly from QEMU 1.7 to 2.1+ without ever packaging
version 2.0.

Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

acpi-dsdt: procedurally generate _PRT

This replaces the _PRT constant with a method that computes it.

The problem is that the DSDT+SSDT have grown from 2.0 to 2.1,
enough to cross the 8k barrier (we align the ACPI tables to 4k
before putting them in fw_cfg).  This causes problems with
migration and the pc-i440fx-2.0 machine type.

The solution to the problem is to hardcode 64k as the limit,
but this doesn't solve the bug with pc-i440fx-2.0.  The fix will be
for QEMU 2.1 to use exactly the same size as QEMU 2.0 for the
ACPI tables.  First, however, we must make the actual AML
equal or smaller; to do this, rewrite _PRT in a way that saves
over 1k of bytecode.

Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

Merge remote-tracking branch 'remotes/mjt/tags/trivial-patches-2014-07-26' into staging

trivial patches for 2014-07-26

# gpg: Signature made Sat 26 Jul 2014 08:16:55 BST using RSA key ID A4C3D7DB
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>"
# gpg:                 aka "Michael Tokarev <mjt@corpit.ru>"
# gpg:                 aka "Michael Tokarev <mjt@debian.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg:          There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6EE1 95D1 886E 8FFB 810D  4324 457C E0A0 8044 65C5
#      Subkey fingerprint: 6F67 E18E 7C91 C5B1 5514  66A7 BEE5 9D74 A4C3 D7DB

* remotes/mjt/tags/trivial-patches-2014-07-26:
  qemu-options: fix another allows-to for -net l2tpv3

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

qemu-options: fix another allows-to for -net l2tpv3

Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging

Here is the serial fix for 2.1.

# gpg: Signature made Fri 25 Jul 2014 13:36:23 BST using RSA key ID 9B4D86F2
# gpg: Good signature from "Paolo Bonzini <pbonzini@redhat.com>"
# gpg:                 aka "Paolo Bonzini <bonzini@gnu.org>"

* remotes/bonzini/tags/for-upstream:
  qemu-char: ignore flow control if a PTY's slave is not connected

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>