Eduardo Habkost [Tue, 6 Mar 2012 18:11:32 +0000 (15:11 -0300)]
add Opteron_G4 CPU model (v2)
This patch addes a Bulldozer-based Opteron_G4 CPU model.
This version has the ffxsr bit actually disabled, to match what was
documented below. Thanks to Andre Przywara for spotting the bug.
I am trying to be conservative with the new model, so I am enabling only
features known to be useful to guests, and not enabling anything that
was not tested or found to be useful to a guest.
List of missing flags in comparison to real hardware:
- vme: host-specific feature.
- osxsave: it is not set here because it is set by the guest OS, not by KVM
- monitor: this is filtered out by the KVM module, so no point in
enabling it.
- mmxext: untested, so not enabled.
- Perf*, Topology*, lwp, ibs: not emulated by KVM.
- wdt, skinit, osvw, altmovcr8, extapicspace, cmplegacy: untested,
so not enabled.
List of new flags, in comparison to the Opteron_G3 model:
- xsave: xsave feature, already implemented by Qemu
- avx, aes, sse4.x, ssse3, pclmulqdq: all new state the new instructions
could use is handled by the xsave state loading/saving code on Qemu.
- pdpe1gb: 1GB pages, supported by the KVM kernel module.
- ffxsr: untested, so not enabled
- fma4, xop: all new state the new instructions could use is handled by
the xsave loading/saving code on Qemu.
- 3dnowprefetch: safe to pass through, though the flag is not used by
Linux guests, at least.
Below is the comparison between the current Opteron_G3 model
and the new model being added.
- The "full" line contains the flags found on actual hardware.
- The "missing" line shows the flags that are present on actual
hardware, but not on the added Opteron_G4 model.
- The "new" line shows the flags that were not on the Opteron_G3 model
but are on Opteron_G4.
feature_edx:
Opteron_G3: sse2 sse fxsr mmx clflush pse36 pat cmov mca pge mtrr sep apic cx8 mce pae msr tsc pse de fpu
full: sse2 sse fxsr mmx clflush pse36 pat cmov mca pge mtrr sep apic cx8 mce pae msr tsc pse de vme fpu
Opteron_G4: sse2 sse fxsr mmx clflush pse36 pat cmov mca pge mtrr sep apic cx8 mce pae msr tsc pse de fpu
missing: vme
Eduardo Habkost [Tue, 6 Mar 2012 18:11:31 +0000 (15:11 -0300)]
add SandyBridge CPU model
This patches add the definition of a SandyBridge CPU model.
Summary of differences:
Flags present on actual hardware, but not on the added model definition:
- pbe, tm, ht, ss, acpi, vme, xTPR, tm2, eist, smx: host-specific
features, not exposed to guest.
- ds, ds-cpl, dtes64, pdcm: emulation not supported by KVM (although it
may be added in the future if implementing PMU virtualization)
- pcid, vmx, monitor: not emulated by Qemu/KVM right now.
- osxsave: set by the guest OS, not by Qemu.
Flags added, that were not present on Westmere model:
- xsave: already supported by Qemu
- avx, pclmulqdq: all new state the new instructions could use is
handled by xsave state loading/saving code.
- tsc-deadline, x2apic, rdtscp: already supported by Qemu/KVM.
Below there's a comparison of the features on the current Westmere CPU
model, and the SandyBridge CPU model.
- The "full" line contains the flags found on actual hardware.
- The "missing" line shows the flags that are present on actual
hardware, but not on the added SandyBridge model.
- The "new" line shows the flags that were not on the Westmere model,
but are on SandyBridge.
feature_edx:
Westmere: sse2 sse fxsr mmx clflush pse36 pat cmov mca pge mtrr sep apic cx8 mce pae msr tsc pse de fpu
full: pbe tm ht ss sse2 sse fxsr mmx ds acpi clflush pse36 pat cmov mca pge mtrr sep apic cx8 mce pge msr tsc pse de vme fpu
SandyBridge: sse2 sse fxsr mmx clflush pse36 pat cmov mca pge mtrr sep apic cx8 mce pae msr tsc pse de fpu
missing: pbe tm ht ss ds acpi vme
Paolo Bonzini [Tue, 28 Feb 2012 08:54:15 +0000 (09:54 +0100)]
qom: fix device hot-unplug
Property removal modifies the list, so it is not safe to continue
iteration. We know anyway that each object can have only one
parent (see object_property_add_child), so exit after finding
the requested object.
Stefan Weil [Sat, 10 Mar 2012 18:59:04 +0000 (19:59 +0100)]
tcg: Improve tcg_out_label and fix its usage for w64
tcg_out_label is always called with a third argument of pointer type
which was casted to tcg_target_long.
These casts can be avoided by changing the prototype of tcg_out_label.
There was also a cast to long. For most hosts with
sizeof(long) == sizeof(tcg_target_long) == sizeof(void *) this did not
matter, but for w64 it was wrong. This is fixed now.
Stefan Weil [Sat, 10 Mar 2012 10:14:31 +0000 (11:14 +0100)]
w64: Don't redefine lseek, ftruncate
MinGW-w64 already defines lseek and ftruncate (and uses the 64 bit
variants). The conditional compilation avoids redefinitions
(which would be wrong) and compiler warnings.
Jan Kiszka [Tue, 6 Mar 2012 17:32:35 +0000 (18:32 +0100)]
gdbstub: Do not kill target in system emulation mode
Too many VM kittens were killed since 7d03f82f81. Another one just died
under my fat fingers.
When you quit a kgdb session, does the Linux kernel power off? Or when
you terminate gdb attached to a hardware debugger, does your board
vanish in space? No.
So let's stop terminating QEMU when the gdbstub receives a kill commando
in system emulation mode. Real termination can still be achieved via
"monitor quit". We keep the behavior for user mode emulation which is
arguably more like a gdbserver scenario.
Jan Kiszka [Tue, 6 Mar 2012 14:22:02 +0000 (15:22 +0100)]
target-i386: Mask NX bit from cpu_get_phys_page_debug result
This was a long pending bug, now revealed by the assert in
phys_page_find that stumbled over the large page index returned by
cpu_get_phys_page_debug for NX-marked pages: We need to mask out NX and
all user-definable bits 52..62 from PDEs and the final PTE to avoid
corrupting physical addresses.
Anthony Liguori [Fri, 9 Mar 2012 18:30:20 +0000 (12:30 -0600)]
Merge remote-tracking branch 'stefanha/trivial-patches' into staging
* stefanha/trivial-patches:
configure: Quote the configure args printed in config.log
osdep: Remove local definition of macro offsetof
libcacard: Spelling and grammar fixes in documentation
Spelling fixes in comments (it's -> its)
vnc: Add break statement
libcacard: Use format specifier %u instead of %d for unsigned values
Fix sign of sscanf format specifiers
block/vmdk: Fix warning from splint (comparision of unsigned value)
qmp: Fix spelling fourty -> forty
qom: Fix spelling in documentation
sh7750: Remove redundant 'struct' from MemoryRegionOps
Anthony Liguori [Fri, 9 Mar 2012 18:29:55 +0000 (12:29 -0600)]
Merge remote-tracking branch 'qemu-kvm/uq/master' into staging
* qemu-kvm/uq/master:
kvm: fill in padding to help valgrind
kvm: x86: Add user space part for in-kernel i8254
kvm: Add kvm_has_pit_state2 helper
i8254: Open-code timer restore
i8254: Factor out base class for KVM reuse
Anthony Liguori [Fri, 9 Mar 2012 18:29:40 +0000 (12:29 -0600)]
Merge remote-tracking branch 'kraxel/usb.42' into staging
* kraxel/usb.42:
xhci: fix port status
xhci: fix control xfers
usb: add shortcut for control transfers
usb-host: enable pipelineing for bulk endpoints.
usb: add pipelining option to usb endpoints
usb: queue can have async packets
uhci_fill_queue: zap debug printf
usb: add USB_RET_IOERROR
usb: return BABBLE rather then NAK when we receive too much data
usb-ehci: Cleanup itd error handling
usb-ehci: Fix and simplify nakcnt handling
usb-ehci: Remove dead nakcnt code
usb-ehci: Fix cerr tracking
usb-ehci: Any packet completion except for NAK should set the interrupt
usb-ehci: Rip the queues when the async or period schedule is halted
usb-ehci: Drop cached qhs when the doorbell gets rung
usb-ehci: always call ehci_queues_rip_unused for period queues
usb-ehci: split our qh queue into async and periodic queues
usb-ehci: Never follow table entries with the T-bit set
usb-redir: Set ep type and interface
Hans de Goede [Fri, 2 Mar 2012 15:49:44 +0000 (16:49 +0100)]
libcacard: Fix compilation with gcc-4.7
VCARD_ATR_PREFIX is used as part of an array initializer so it should
not have () around it, so far this happened to work, but gcc-4.7 does
not like it.
Peter Maydell [Wed, 7 Mar 2012 12:16:29 +0000 (12:16 +0000)]
configure: Quote the configure args printed in config.log
Use the same mechanism we use for printing the configure command
line to config-host.mak to print it to config.log. This fixes a
bug where the config.log version didn't quote arguments with spaces.
Stefan Weil [Mon, 5 Mar 2012 06:22:31 +0000 (07:22 +0100)]
osdep: Remove local definition of macro offsetof
The macro offsetof is defined in stddef.h. It is conforming to
the standards C89, C99 and POSIX.1-2001 (see man page), so it
is a sufficiently old standard.
Therefore chances are very high that QEMU never needs a local
definition of this macro.
osdep.h already includes stddef.h, so this patch simply removes
the unneeded code from the files configure and osdep.h.
If we ever need the local definition again, it should be added
to compiler.h (the macro is usually provided with the compiler,
it is not OS specific).
Stefan Weil [Sun, 26 Feb 2012 17:46:12 +0000 (18:46 +0100)]
Spelling fixes in comments (it's -> its)
* it's -> its (fixed for all files)
* dont -> don't (only fixed in a line which was touched by the previous fix)
* distrub -> disturb (fixed in the same line)
Gerd Hoffmann [Thu, 1 Mar 2012 14:14:12 +0000 (15:14 +0100)]
xhci: fix port status
Don't signal port status change if the usb device isn't in attached
state. Happens with usb-host devices with the pass-through device
being plugged out at the host.
Gerd Hoffmann [Thu, 1 Mar 2012 14:51:51 +0000 (15:51 +0100)]
xhci: fix control xfers
Use the new, direct control transfer submission method instead of
bypassing the usb core by calling usb_device_handle_control directly.
The later fails for async control transfers.
Gerd Hoffmann [Fri, 2 Mar 2012 12:22:29 +0000 (13:22 +0100)]
usb: add shortcut for control transfers
Add a more direct code path to submit control transfers. Instead of
feeding three usb packets (setup, data, ack) to usb_handle_packet and
have the do_token_* functions in usb.c poke the control transfer
parameters out of it just submit a single packet carrying the actual
data with the control xfer parameters filled into USBPacket->parameters.
Gerd Hoffmann [Thu, 1 Mar 2012 13:39:28 +0000 (14:39 +0100)]
usb: add pipelining option to usb endpoints
With this patch applied USB drivers can enable pipelining per endpoint.
With pipelining enabled the usb core will continue submitting packets
even when there are still async transfers in flight instead of passing
them on one by one.
Gerd Hoffmann [Tue, 28 Feb 2012 14:36:06 +0000 (15:36 +0100)]
usb: queue can have async packets
This can happen today in case the ->complete() callback queues up the
next packet. Also we'll support pipelining soon, which allows to have
multiple packets per queue in flight (aka ASYNC) state.
Hans de Goede [Fri, 2 Mar 2012 20:27:20 +0000 (21:27 +0100)]
usb: add USB_RET_IOERROR
We already have USB_RET_NAK, but that means that a device does not want
to send/receive right now. But with host / network redirection we can
actually have a transaction fail due to some io error, rather then ie
the device just not having any data atm.
This patch adds a new error code named USB_RET_IOERROR for this, and uses
it were appropriate.
Notes:
-Currently all usb-controllers handle this the same as NODEV, but that
may change in the future, OHCI could indicate a CRC error instead for example.
-This patch does not touch hw/usb-musb.c, that is because the code in there
handles STALL and NAK specially and has a if status < 0 generic catch all
for all other errors
Hans de Goede [Fri, 2 Mar 2012 20:27:17 +0000 (21:27 +0100)]
usb-ehci: Fix and simplify nakcnt handling
The nakcnt code in ehci_execute_complete() marked transactions as finished
when a packet completed with a result of USB_RET_NAK, but USB_RET_NAK
means that the device cannot receive / send data at that time and that
the transaction should be retried later, which is also what the usb-uhci
and usb-ohci code does.
Note that there already was some special code in place to handle this
for interrupt endpoints in the form of doing a return from
ehci_execute_complete() when reload == 0, but that for bulk transactions
this was not handled correctly (where as for example the usb-ccid device does
return USB_RET_NAK for bulk packets).
Besides that the code in ehci_execute_complete() decrement nakcnt by 1
on a packet result of USB_RET_NAK, but
-since the transaction got marked as finished,
nakcnt would never be decremented again
-there is no code checking for nakcnt becoming 0
-there is no use in re-trying the transaction within the same usb frame /
usb-ehci frame-timer call, since the status of emulated devices won't change
as long as the usb-ehci frame-timer is running
So we should simply set the nakcnt to 0 when we get a USB_RET_NAK, thus
claiming that we've tried reload times (or as many times as possible if
reload is 0).
Besides the code in ehci_execute_complete() handling USB_RET_NAK there
was also code handling it in ehci_state_executing(), which calls
ehci_execute_complete(), and then does its own handling on top of the handling
in ehci_execute_complete(), this code would decrement nakcnt *again* (if not
already 0), or restore the reload value (which was never changed) on success.
Since the double decrement was wrong to begin with, and is no longer needed
now that we set nakcnt directly to 0 on USB_RET_NAK, and the restore of reload
is not needed either, this patch simply removes all nakcnt handling from
ehci_state_executing().
Hans de Goede [Fri, 2 Mar 2012 20:27:16 +0000 (21:27 +0100)]
usb-ehci: Remove dead nakcnt code
This patch removes 2 bits of dead nakcnt code:
1) usb_ehci_execute calls ehci_qh_do_overlay which does:
nakcnt = reload;
and then has a block of code which is conditional on:
if (reload && !nakcnt) {
which ofcourse is never true now as nakcnt == reload.
2) ehci_state_fetchqh does:
nakcnt = reload;
but before nakcnt is ever used ehci_state_fetchqh is always followed
by a ehci_qh_do_overlay call which also does:
nakcnt = reload;
So doing this from ehci_state_fetchqh is redundant.
Hans de Goede [Fri, 2 Mar 2012 20:27:15 +0000 (21:27 +0100)]
usb-ehci: Fix cerr tracking
cerr should only be decremented on errors which cause XactErr to be set, and
when that happens the failing transaction should be retried until cerr reaches
0 and only then should USBSTS_ERRINT be set (and inactive cleared and
USBSTS_INT set if requested).
Since we don't have any hardware level errors (and in case of redirection
the real hardware has already retried), re-trying makes no sense, so
immediately set cerr to 0 on errors which set XactErr.
Hans de Goede [Fri, 2 Mar 2012 20:27:12 +0000 (21:27 +0100)]
usb-ehci: Drop cached qhs when the doorbell gets rung
The purpose of the IAAD bit / the doorbell is to make the ehci controller
forget about cached qhs, this is mainly used when cancelling transactions,
the qh is unlinked from the async schedule and then the doorbell gets rung,
once the doorbell is acked by the controller the hcd knows that the qh is
no longer in use and that it can do something else with the memory, such
as re-use it for a new qh! But we keep our struct representing this qh around
for circa 250 ms. This allows for a (mightily large) race window where the
following could happen:
-hcd submits a qh at address 0xdeadbeef
-our ehci code sees the qh, sends a request to a usb-device, gets a result
of USB_RET_ASYNC, sets the async_state of the qh to EHCI_ASYNC_INFLIGHT
-hcd unlinks the qh at address 0xdeadbeef
-hcd rings the doorbell, wait for us to ack it
-hcd re-uses the qh at address 0xdeadbeef
-our ehci code sees the qh, looks in the async_queue, sees there already is
a qh at address 0xdeadbeef there with async_state of EHCI_ASYNC_INFLIGHT,
does nothing
-the *original* (which the hcd thinks it has cancelled) transaction finishes
-our ehci code sees the qh on yet another pass through the async list,
looks in the async_queue, sees there already is a qh at address 0xdeadbeef
there with async_state of EHCI_ASYNC_COMPLETED, and finished the transaction
with the results of the *original* transaction.
Not good (tm), this patch fixes this race by removing all qhs which have not
been seen during the last cycle through the async list immidiately when the
doorbell is rung.
Note this patch does not fix any actually observed problem, but upon
reading of the EHCI spec it became apparent to me that the above race could
happen and the usb-ehci behavior from before this patch is not good.
Hans de Goede [Fri, 2 Mar 2012 20:27:11 +0000 (21:27 +0100)]
usb-ehci: always call ehci_queues_rip_unused for period queues
Before this patch USB 2 devices with interrupt endpoints were not working
properly. The problem is that to avoid loops we stop processing as soon
as we encounter a queue-head (qh) we've already seen since qhs can be linked
in a circular fashion, this is tracked by the seen flag in our qh struct.
The resetting of the seen flag is done from ehci_queues_rip_unused which
before this patch was only called when executing the statemachine for the
async schedule.
But packets for interrupt endpoints are part of the periodic schedule! So what
would happen is that when there were no ctrl or bulk packets for a USB 2
device with an interrupt endpoint, the async schedule would become non
active, then ehci_queues_rip_unused would no longer get called and when
processing the qhs for the interrupt endpoints from the periodic schedule
their seen bit would still be 1 and they would be skipped.
Hans de Goede [Fri, 2 Mar 2012 20:27:10 +0000 (21:27 +0100)]
usb-ehci: split our qh queue into async and periodic queues
qhs can be part of both the async and the periodic schedule, as is shown
in later patches in this series it is useful to keep track of the qhs on
a per schedule basis.
Hans de Goede [Fri, 2 Mar 2012 20:27:08 +0000 (21:27 +0100)]
usb-redir: Set ep type and interface
Since we don't use usb_desc.c we need to do this ourselves. This fixes
iso transfers no longer working for USB 2 devices due to the ep->type
check in ehci.c
valgrind warns about padding fields which are passed
to vcpu ioctls uninitialized.
This is not an error in practice because kvm ignored padding.
Since the ioctls in question are off data path and
the cost is zero anyway, initialize padding to 0
to suppress these errors.
Jan Kiszka [Fri, 2 Mar 2012 19:28:49 +0000 (20:28 +0100)]
kvm: x86: Add user space part for in-kernel i8254
This provides the required user space stubs to enable the in-kernel
i8254 emulation of KVM.
The in-kernel model supports lost tick compensation according to the
"delay" policy. This is enabled by default and can be switched off via a
device property.
Depending on the feature set of the host kernel (before 2.6.32), we may
have to disable the HPET or lack sound output from the PC speaker.
Jan Kiszka [Fri, 2 Mar 2012 19:28:47 +0000 (20:28 +0100)]
i8254: Open-code timer restore
Same as for the APIC: To enable migration between accelerated and
non-accelerated models, we need to arm the channel 0 timer only inside
the emulated PIT model. The common code just saves/restores that timer
to the the next_transition_time field.
Jan Kiszka [Fri, 2 Mar 2012 19:28:46 +0000 (20:28 +0100)]
i8254: Factor out base class for KVM reuse
Applying the concept used for the *PICs once again: establish a base
class for the i8254 that can be used both by the current user space
emulation and the upcoming KVM in-kernel version. We share most of the
public interface of the i8254, specifically to the pcspk, vmstate, reset
and certain init parts.
s390: Rework kernel loading: supports elf and newer kernels
This reworks the image loading on s390.
Newer kernels will not always have a 0dd0 (basr 13,0) at address 0x10000.
We must not rely on specific code at certain addresses. This check was
introduced to warn users that tried to load vmlinux, since ELF loading
was not supported. Lets wire that up. If elf loading fails, we assume
that this is a standard kernel image and load that via load_image_targphys.
This patch also changes all other users of load_image to
load_image_targphys to be consistent. (the elf loader registers the kernel
as rom).
Avi Kivity [Mon, 5 Mar 2012 15:40:12 +0000 (17:40 +0200)]
memory: fix I/O port aliases
Commit e58ac72b6a0 ("ioport: change portio_list not to use
memory_region_set_offset()") started using aliases of I/O memory
regions. Since the IORange used for the I/O was contained in the
target region, the alias information (specifically, the offset
into the region) was lost. This broke -vga std.
Fix by allocating an independent object to hold the IORange and
also the new offset.
Note that I/O memory regions were conceptually broken wrt aliases
in a different way: an alias can cause the same region to appear
twice in an address space, but we had just one IORange to service it.
This patch fixes that problem as well, since we can now have multiple
IORange/MemoryRegion associations.
Avi Kivity [Mon, 5 Mar 2012 15:36:19 +0000 (17:36 +0200)]
ioport: add destructor method to IORange
Previously all callers had a containing object with a destructor that
could be used to trigger cleanup of the IORange objects (typically
just freeing the containing object), but a forthcoming memory API
change doesn't fit this pattern. Rather than setting up a new global
table, extend the ioport system to support destructors.
Stefan Weil [Fri, 2 Mar 2012 22:30:04 +0000 (23:30 +0100)]
w64: Fix data type of parameters for flush_icache_range
flush_icache_range takes two address parameters which must be large
enough to address any address of the host.
For hosts with sizeof(unsigned long) == sizeof(void *), this patch
changes nothing. All currently supported hosts fall into this category.
For w64 hosts, sizeof(unsigned long) is 4 while sizeof(void *) is 8,
so the use of tcg_target_ulong is needed for i386 and tci (the tcg
targets which work with w64).
Blue Swirl [Sat, 3 Mar 2012 17:59:06 +0000 (17:59 +0000)]
Merge branch 'upstream' of git://qemu.weilnetz.de/qemu
* 'upstream' of git://qemu.weilnetz.de/qemu:
Move definition of HOST_LONG_BITS to qemu-common.h
target-xtensa: Clean includes
target-unicore32: Clean includes
target-sh4: Clean includes
target-s390x: Clean includes
target-ppc: Clean includes
target-mips: Clean includes
target-microblaze: Clean includes
target-m68k: Clean includes
target-lm32: Clean includes
target-i386: Clean includes
target-cris: Clean includes
target-arm: Clean includes
target-alpha: Clean includes
Remove macro HOST_LONG_SIZE
Blue Swirl [Sat, 3 Mar 2012 17:53:56 +0000 (17:53 +0000)]
Merge branch 'arm-devs.for-upstream' of git://git.linaro.org/people/pmaydell/qemu-arm
* 'arm-devs.for-upstream' of git://git.linaro.org/people/pmaydell/qemu-arm:
hw/arm11mpcore: Fix broken realview_mpcore/arm11mpcore_priv properties
arm: add device tree support
arm: make sure that number of irqs can be represented in GICD_TYPER.
arm: clean up GIC constants
Fix confusion in the Property arrays for the "arm11mpcore_priv"
(per-CPU devices for the ARM11MPcore CPU) and "realview_mpcore"
(realview-eb board specific device encapsulating CPU and some
extra interrupt controllers) -- the num-irq property was defined
on the wrong device and the mpcore_rirq_properties were defined
as offsets in the wrong structure. The effect was that the
realview-eb-mpcore machine would abort on startup trying to
allocate an insane amount of memory. (This bug was introduced in
the QOM conversion in commit 999e12bb.)
Grant Likely [Fri, 2 Mar 2012 11:56:38 +0000 (11:56 +0000)]
arm: add device tree support
If compiled with CONFIG_FDT, allow user to specify a device tree file using
the -dtb argument. If the machine supports it then the dtb will be loaded
into memory and passed to the kernel on boot.
Signed-off-by: Jeremy Kerr <[email protected]> Signed-off-by: Grant Likely <[email protected]>
[Peter Maydell: Use machine opt rather than global to pass dtb filename] Signed-off-by: Peter Maydell <[email protected]>
Rusty Russell [Fri, 2 Mar 2012 11:56:38 +0000 (11:56 +0000)]
arm: make sure that number of irqs can be represented in GICD_TYPER.
We currently assume that the number of interrupts (ITLinesNumber in
the architecture reference manual) is divisible by 32, since we
present it to the guest when it reads GICD_TYPER (in gic_dist_readb())
as (N / 32) - 1.
Anthony Liguori [Thu, 1 Mar 2012 21:26:25 +0000 (15:26 -0600)]
Merge remote-tracking branch 'qemu-kvm/memory/core' into staging
* qemu-kvm/memory/core: (30 commits)
memory: allow phys_map tree paths to terminate early
memory: unify PhysPageEntry::node and ::leaf
memory: change phys_page_set() to set multiple pages
memory: switch phys_page_set() to a recursive implementation
memory: replace phys_page_find_alloc() with phys_page_set()
memory: simplify multipage/subpage registration
memory: give phys_page_find() its own tree search loop
memory: make phys_page_find() return a MemoryRegionSection
memory: move tlb flush to MemoryListener commit callback
memory: unify the two branches of cpu_register_physical_memory_log()
memory: fix RAM subpages in newly initialized pages
memory: compress phys_map node pointers to 16 bits
memory: store MemoryRegionSection pointers in phys_map
memory: unify phys_map last level with intermediate levels
memory: remove first level of l1_phys_map
memory: change memory registration to rebuild the memory map on each change
memory: support stateless memory listeners
memory: split memory listener for the two address spaces
xen: ignore I/O memory regions
memory: allow MemoryListeners to observe a specific address space
...
Anthony Liguori [Thu, 1 Mar 2012 21:26:01 +0000 (15:26 -0600)]
Merge remote-tracking branch 'qemu-kvm/uq/master' into staging
* qemu-kvm/uq/master:
pc-bios: update kvmvapic.bin
kvmvapic: Use optionrom helpers
optionsrom: Reserve space for checksum
kvmvapic: Simplify mp/up_set_tpr
kvmvapic: Introduce TPR access optimization for Windows guests
kvmvapic: Add option ROM
target-i386: Add infrastructure for reporting TPR MMIO accesses
Allow to use pause_all_vcpus from VCPU context
Process pending work while waiting for initial kick-off in TCG mode
Remove useless casts from cpu iterators
kvm: Set cpu_single_env only once
kvm: Synchronize cpu state in kvm_arch_stop_on_emulation_error()
Avi Kivity [Wed, 29 Feb 2012 11:22:12 +0000 (13:22 +0200)]
kvm: fix unaligned slots
kvm_set_phys_mem() may be passed sections that are not aligned to a page
boundary. The current code simply brute-forces the alignment which leads
to an inconsistency and an abort().
Fix by aligning the start and the end of the section correctly, discarding
and unaligned head or tail.
This was triggered by a guest sizing a 64-bit BAR that is smaller than a page
with PCI_COMMAND_MEMORY enabled and the upper dword clear.
Anthony Liguori [Wed, 29 Feb 2012 18:57:28 +0000 (12:57 -0600)]
Merge remote-tracking branch 'kwolf/for-anthony' into staging
* kwolf/for-anthony: (27 commits)
qemu-img: fix segment fault when the image format is qed
qemu-io: fix segment fault when the image format is qed
qemu-tool: revert cpu_get_clock() abort(3)
qemu-iotests: Test rebase with short backing file
qemu-iotests: 026: Reduce output changes for cache=none qcow2
qemu-iotests: Filter out DOS line endings
test: add image streaming tests
qemu-iotests: add iotests Python module
qemu-iotests: export TEST_DIR for non-bash tests
QMP: Add qmp command for blockdev-group-snapshot-sync
qapi: Introduce blockdev-group-snapshot-sync command
qcow2: Reject too large header extensions
qcow2: Fix offset in qcow2_read_extensions
block: drop aio_multiwrite in BlockDriver
block: remove unused fields in BlockDriverState
qcow2: Fix build with DEBUG_EXT enabled
ide: fail I/O to empty disk
fdc: DIR (Digital Input Register) should return status of current drive...
fdc: fix seek command, which shouldn't check tracks
fdc: check if media rate is correct before doing any transfer
...
Anthony Liguori [Wed, 29 Feb 2012 15:11:00 +0000 (09:11 -0600)]
Merge remote-tracking branch 'kraxel/usb.39' into staging
* kraxel/usb.39: (21 commits)
usb: Resolve warnings about unassigned bus on usb device creation
usb-redir: Return USB_RET_NAK when we've no data for an interrupt endpoint
usb-redir: Limit return values returned by iso packets
usb-redir: Let the usb-host know about our device filtering
usb-redir: Always clear device state on filter reject
usb-redir: Fix printing of device version
ehci: drop old stuff
usb-ehci: Handle ISO packets failing with an error other then NAK
libcacard: fix reported ATR length
usb-ccid: advertise SELF_POWERED
libcacard: link with glib for g_strndup
usb-desc: fix user trigerrable segfaults (!config)
usb-ehci: sanity-check iso xfers
usb: add tracepoint for usb packet state changes.
usb-xhci: enable packet queuing
usb-uhci: implement packet queuing
usb-uhci: process uhci_handle_td return code via switch.
usb-uhci: add UHCIQueue
usb-uhci: cleanup UHCIAsync allocation & initialization.
usb-ehci: fix reset
...
qemu-img: fix segment fault when the image format is qed
[root@f15 qemu]# qemu-img info /home/zwu/work/misc/rh6.img
image: /home/zwu/work/misc/rh6.img
file format: qed
virtual size: 4.0G (4294967296 bytes)
disk size: 1.2G
cluster_size: 65536
Segmentation fault (core dumped)
Today when i were fixing another issue, i found this issue; After simple
investigation, i found that the required clock vm_clock is not created
for qemu tool.
qemu-io: fix segment fault when the image format is qed
[root@f15 qemu]# qemu-io -c info /home/zwu/work/misc/rh6.img
format name: qed
cluster size: 64 KiB
vm state offset: 0.000000 bytes
Segmentation fault (core dumped)
Stefan Hajnoczi [Wed, 29 Feb 2012 14:41:32 +0000 (14:41 +0000)]
qemu-tool: revert cpu_get_clock() abort(3)
Despite the fact that the qemu-tool environment has no guest running and
vm_clock therefore does not make sense, there is code that gets the
vm_clock time even in qemu-tool. Therefore, revert the abort(3) call
and just return 0 like we used to. This unbreaks qemu-img/qemu-io with
QED and Kevin has also expressed interest in this for qcow2.
Kevin Wolf [Fri, 29 Apr 2011 13:32:55 +0000 (15:32 +0200)]
qemu-iotests: 026: Reduce output changes for cache=none qcow2
qemu-iotests supports the -nocache option which makes the tests run with
cache=none. For blkdebug tests with qcow2 this means that we may see
test results that differ from cache=writethrough. This patch makes the
diff a bit smaller and therefore easier to review.
Stefan Hajnoczi [Wed, 29 Feb 2012 13:25:22 +0000 (13:25 +0000)]
test: add image streaming tests
This patch adds a test suite for the image streaming feature. It
exercises the 'block_stream', 'block_job_cancel', 'block_job_set_speed',
and 'query-block-jobs' QMP commands.
Stefan Hajnoczi [Wed, 29 Feb 2012 13:25:21 +0000 (13:25 +0000)]
qemu-iotests: add iotests Python module
Block layer tests that involve QMP commands rather than qemu-img or
qemu-io are not well-suited for shell scripting. This patch adds a
Python module which allows tests to be written in Python instead.
The basic API is:
VM - class for launching and interacting with a VM
QMPTestCase - abstract base class for tests that use QMP
qemu_img() - wrapper function for invoking qemu-img
qemu_io() - wrapper function for invoking qemu-io
imgfmt - the image format under test (e.g. qcow2, qed)
test_dir - scratch directory path for temporary files
main() - entry point for running tests
Stefan Hajnoczi [Wed, 29 Feb 2012 13:25:20 +0000 (13:25 +0000)]
qemu-iotests: export TEST_DIR for non-bash tests
Since qemu-iotests may need to create large image files it is possible
to specify the test directory. The TEST_DIR variable needs to be
exported so non-bash tests can make use of it.
Jeff Cody [Tue, 28 Feb 2012 20:54:07 +0000 (15:54 -0500)]
QMP: Add qmp command for blockdev-group-snapshot-sync
This adds the QMP command for blockdev-group-snapshot-sync. It
takes an array in as the input, for the argument devlist. The
array consists of the following elements:
+ device: device to snapshot. e.g. "ide-hd0", "virtio0"
+ snapshot-file: path & file for the snapshot image. e.g. "/tmp/file.img"
+ format: snapshot format. e.g., "qcow2". Optional
projects / qemu.git / log