Joseph Myers [Tue, 23 Jun 2020 00:01:38 +0000 (00:01 +0000)]
target/i386: reimplement fpatan using floatx80 operations
The x87 fpatan emulation is currently based around conversion to
double. This is inherently unsuitable for a good emulation of any
floatx80 operation. Reimplement using the soft-float operations, as
for other such instructions.
Joseph Myers [Wed, 17 Jun 2020 23:24:29 +0000 (23:24 +0000)]
target/i386: reimplement fyl2x using floatx80 operations
The x87 fyl2x emulation is currently based around conversion to
double. This is inherently unsuitable for a good emulation of any
floatx80 operation. Reimplement using the soft-float operations,
building on top of the reimplementation of fyl2xp1 and factoring out
code to be shared between the two instructions.
The included test assumes that the result in round-to-nearest mode
should always be one of the two closest floating-point numbers to the
mathematically exact result (including that it should be exact, in the
exact cases which cover more cases than for fyl2xp1).
Joseph Myers [Wed, 17 Jun 2020 23:20:50 +0000 (23:20 +0000)]
target/i386: reimplement fyl2xp1 using floatx80 operations
The x87 fyl2xp1 emulation is currently based around conversion to
double. This is inherently unsuitable for a good emulation of any
floatx80 operation, even before considering that it is a particularly
naive implementation using double (adding 1 then using log rather than
attempting a better emulation using log1p).
Reimplement using the soft-float operations, as was done for f2xm1; as
in that case, m68k has related operations but not exactly this one and
it seemed safest to implement directly rather than reusing the m68k
code to avoid accumulation of errors.
A test is included with many randomly generated inputs. The
assumption of the test is that the result in round-to-nearest mode
should always be one of the two closest floating-point numbers to the
mathematical value of y * log2(x + 1); the implementation aims to do
somewhat better than that (about 70 correct bits before rounding). I
haven't investigated how accurate hardware is.
Intel manuals describe a narrower range of valid arguments to this
instruction than AMD manuals. The implementation accepts the wider
range (it's needed anyway for the core code to be reusable in a
subsequent patch reimplementing fyl2x), but the test only has inputs
in the narrower range so that it's valid on hardware that may reject
or produce poor results for inputs outside that range.
Code in the previous implementation that sets C2 for some out-of-range
arguments is not carried forward to the new implementation; C2 is
undefined for this instruction and I suspect that code was just
cut-and-pasted from the trigonometric instructions (fcos, fptan, fsin,
fsincos) where C2 *is* defined to be set for out-of-range arguments.
Joseph Myers [Mon, 8 Jun 2020 16:58:23 +0000 (16:58 +0000)]
target/i386: reimplement fprem, fprem1 using floatx80 operations
The x87 fprem and fprem1 emulation is currently based around
conversion to double, which is inherently unsuitable for a good
emulation of any floatx80 operation. Reimplement using the soft-float
floatx80 remainder operations.
Joseph Myers [Mon, 8 Jun 2020 16:57:16 +0000 (16:57 +0000)]
softfloat: return low bits of quotient from floatx80_modrem
Both x87 and m68k need the low parts of the quotient for their
remainder operations. Arrange for floatx80_modrem to track those bits
and return them via a pointer.
The architectures using float32_rem and float64_rem do not appear to
need this information, so the *_rem interface is left unchanged and
the information returned only from floatx80_modrem. The logic used to
determine the low 7 bits of the quotient for m68k
(target/m68k/fpu_helper.c:make_quotient) appears completely bogus (it
looks at the result of converting the remainder to integer, the
quotient having been discarded by that point); this patch does not
change that, but the m68k maintainers may wish to do so.
Joseph Myers [Mon, 8 Jun 2020 16:56:47 +0000 (16:56 +0000)]
softfloat: do not set denominator high bit for floatx80 remainder
The floatx80 remainder implementation unnecessarily sets the high bit
of bSig explicitly. By that point in the function, arguments that are
invalid, zero, infinity or NaN have already been handled and
subnormals have been through normalizeFloatx80Subnormal, so the high
bit will already be set. Remove the unnecessary code.
Joseph Myers [Mon, 8 Jun 2020 16:56:20 +0000 (16:56 +0000)]
softfloat: do not return pseudo-denormal from floatx80 remainder
The floatx80 remainder implementation sometimes returns the numerator
unchanged when the denominator is sufficiently larger than the
numerator. But if the value to be returned unchanged is a
pseudo-denormal, that is incorrect. Fix it to normalize the numerator
in that case.
Joseph Myers [Mon, 8 Jun 2020 16:55:49 +0000 (16:55 +0000)]
softfloat: fix floatx80 remainder pseudo-denormal check for zero
The floatx80 remainder implementation ignores the high bit of the
significand when checking whether an operand (numerator) with zero
exponent is zero. This means it mishandles a pseudo-denormal
representation of 0x1p-16382L by treating it as zero. Fix this by
checking the whole significand instead.
Joseph Myers [Mon, 8 Jun 2020 16:55:11 +0000 (16:55 +0000)]
softfloat: merge floatx80_mod and floatx80_rem
The m68k-specific softfloat code includes a function floatx80_mod that
is extremely similar to floatx80_rem, but computing the remainder
based on truncating the quotient toward zero rather than rounding it
to nearest integer. This is also useful for emulating the x87 fprem
and fprem1 instructions. Change the floatx80_rem implementation into
floatx80_modrem that can perform either operation, with both
floatx80_rem and floatx80_mod as thin wrappers available for all
targets.
There does not appear to be any use for the _mod operation for other
floating-point formats in QEMU (the only other architectures using
_rem at all are linux-user/arm/nwfpe, for FPA emulation, and openrisc,
for instructions that have been removed in the latest version of the
architecture), so no change is made to the code for other formats.
Joseph Myers [Thu, 11 Jun 2020 23:45:48 +0000 (23:45 +0000)]
target/i386: reimplement f2xm1 using floatx80 operations
The x87 f2xm1 emulation is currently based around conversion to
double. This is inherently unsuitable for a good emulation of any
floatx80 operation, even before considering that it is a particularly
naive implementation using double (computing with pow and then
subtracting 1 rather than attempting a better emulation using expm1).
Reimplement using the soft-float operations, including additions and
multiplications with higher precision where appropriate to limit
accumulation of errors. I considered reusing some of the m68k code
for transcendental operations, but the instructions don't generally
correspond exactly to x87 operations (for example, m68k has 2^x and
e^x - 1, but not 2^x - 1); to avoid possible accumulation of errors
from applying multiple such operations each rounding to floatx80
precision, I wrote a direct implementation of 2^x - 1 instead. It
would be possible in principle to make the implementation more
efficient by doing the intermediate operations directly with
significands, signs and exponents and not packing / unpacking floatx80
format for each operation, but that would make it significantly more
complicated and it's not clear that's worthwhile; the m68k emulation
doesn't try to do that.
A test is included with many randomly generated inputs. The
assumption of the test is that the result in round-to-nearest mode
should always be one of the two closest floating-point numbers to the
mathematical value of 2^x - 1; the implementation aims to do somewhat
better than that (about 70 correct bits before rounding). I haven't
investigated how accurate hardware is.
Thomas Huth [Mon, 15 Jun 2020 07:26:29 +0000 (09:26 +0200)]
hw/scsi/megasas: Fix possible out-of-bounds array access in tracepoints
Some tracepoints in megasas.c use a guest-controlled value as an index
into the mfi_frame_desc[] array. Thus a malicious guest could cause an
out-of-bounds error here. Fortunately, the impact is very low since this
can only happen when the corresponding tracepoints have been enabled
before, but the problem should be fixed anyway with a proper check.
Jingqi Liu [Wed, 29 Apr 2020 08:50:10 +0000 (16:50 +0800)]
docs/nvdimm: add description of alignment requirement of device dax
For device dax (e.g., /dev/dax0.0), the NUM of 'align=NUM' option
needs to match the alignment requirement of the device dax.
It must be larger than or equal to the 'align' of device dax.
Jingqi Liu [Wed, 29 Apr 2020 08:50:09 +0000 (16:50 +0800)]
exec: fetch the alignment of Linux devdax pmem character device nodes
If the backend file is devdax pmem character device, the alignment
specified by the option 'align=NUM' in the '-object memory-backend-file'
needs to match the alignment requirement of the devdax pmem character device.
This patch uses the interfaces of libdaxctl to fetch the devdax pmem file
'align', so that we can compare it with the NUM of 'align=NUM'.
The NUM needs to be larger than or equal to the devdax pmem file 'align'.
It also fixes the problem that mmap() returns failure in qemu_ram_mmap()
when the NUM of 'align=NUM' is less than the devdax pmem file 'align'.
Jingqi Liu [Wed, 29 Apr 2020 08:50:11 +0000 (16:50 +0800)]
configure: add libdaxctl support
Add a pair of configure options --{enable,disable}-libdaxctl to control
whether QEMU is compiled with libdaxctl [1]. Libdaxctl is a utility
library for managing the device dax subsystem.
QEMU uses mmap(2) to maps vNVDIMM backends and aligns the mapping
address to the page size (getpagesize(2)) by default. However, some
types of backends may require an alignment different than the page
size. The 'align' option is provided to memory-backend-file to allow
users to specify the proper alignment.
For device dax (e.g., /dev/dax0.0), the 'align' option needs to match
the alignment requirement of the device dax, which can be fetched
through the APIs of libdaxctl version 57 or up.
[1] Libdaxctl is a part of ndctl project.
The project's repository is: https://github.com/pmem/ndctl
For more information about libdaxctl APIs, you can refer to the
comments in source code of: pmem/ndctl/daxctl/lib/libdaxctl.c.
Pavel Dovgalyuk [Fri, 22 May 2020 06:35:27 +0000 (09:35 +0300)]
replay: synchronize on every virtual timer callback
Sometimes virtual timer callbacks depend on order
of virtual timer processing and warping of virtual clock.
Therefore every callback should be logged to make replay deterministic.
This patch creates a checkpoint before every virtual timer callback.
With these checkpoints virtual timers processing and clock warping
events order is completely deterministic.
Pavel Dovgalyuk [Fri, 22 May 2020 06:47:58 +0000 (09:47 +0300)]
replay: notify the main loop when there are no instructions
When QEMU is executed in console mode without any external event sources,
main loop may sleep for a very long time. But in case of replay
there is another event source - event log.
This patch adds main loop notification when the vCPU loop has nothing
to do and main loop should process the inputs from the event log.
memory: Revert "memory: accept mismatching sizes in memory_region_access_valid"
Memory API documentation documents valid .min_access_size and .max_access_size
fields and explains that any access outside these boundaries is blocked.
This is what devices seem to assume.
However this is not what the implementation does: it simply
ignores the boundaries unless there's an "accepts" callback.
Naturally, this breaks a bunch of devices.
Revert to the documented behaviour.
Devices that want to allow any access can just drop the valid field,
or add the impl field to have accesses converted to appropriate
length.
Jay Zhou [Wed, 4 Mar 2020 02:55:54 +0000 (10:55 +0800)]
kvm: support to get/set dirty log initial-all-set capability
Since the new capability KVM_DIRTY_LOG_INITIALLY_SET of
KVM_CAP_MANUAL_DIRTY_LOG_PROTECT2 has been introduced in the
kernel, tweak the userspace side to detect and enable this
capability.
Peter Maydell [Thu, 25 Jun 2020 20:20:44 +0000 (21:20 +0100)]
Merge remote-tracking branch 'remotes/xtensa/tags/20200625-xtensa' into staging
target/xtensa fixes for 5.1:
- fix access to special registers missing in the core configuration;
- fix simcall opcode behavior for new hardware;
- drop gen_io_end call from xtensa translator.
* remotes/xtensa/tags/20200625-xtensa:
target/xtensa: drop gen_io_end call
target/xtensa: fix simcall for newer hardware
target/xtensa: fetch HW version from configuration overlay
target/xtensa: work around missing SR definitions
Peter Maydell [Thu, 25 Jun 2020 15:52:42 +0000 (16:52 +0100)]
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,acpi,pci: fixes, cleanups.
Fixes, cleanups in ACPI, PCI, virtio.
Signed-off-by: Michael S. Tsirkin <[email protected]>
# gpg: Signature made Thu 25 Jun 2020 07:48:47 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "[email protected]"
# gpg: Good signature from "Michael S. Tsirkin <[email protected]>" [full]
# gpg: aka "Michael S. Tsirkin <[email protected]>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
Rename use_acpi_pci_hotplug to more appropriate use_acpi_hotplug_bridge
Stop vhost-user sending uninitialized mmap_offsets
docs/specs/tpm: ACPI boot now supported for TPM/ARM
arm/acpi: Add the TPM2.0 device under the DSDT
acpi: Some build_tpm2() code reshape
tests/acpi: update expected data files
acpi: q35: drop _SB.PCI0.ISA.LPCD opregion.
acpi: drop build_piix4_pm()
acpi: drop serial/parallel enable bits from dsdt
acpi: simplify build_isa_devices_aml()
acpi: factor out fw_cfg_add_acpi_dsdt()
acpi: move aml builder code for i8042 (kbd+mouse) device
floppy: move cmos_get_fd_drive_type() from pc
floppy: make isa_fdc_get_drive_max_chs static
acpi: move aml builder code for floppy device
acpi: bios-tables-test: show more context on asl diffs
qtest: allow DSDT acpi table changes
* remotes/armbru/tags/pull-qdev-2020-06-23:
sd/milkymist-memcard: Fix error API violation
sd/pxa2xx_mmci: Don't crash on pxa2xx_mmci_init() error
arm/aspeed: Drop aspeed_board_init_flashes() parameter @errp
qdev: Make qdev_prop_set_drive() match the other helpers
qdev: Reject chardev property override
qdev: Reject drive property override
qdev: Improve netdev property override error a bit
qdev: Eliminate get_pointer(), set_pointer()
blockdev: Deprecate -drive with bogus interface type
docs/qdev-device-use.txt: Update section "Default Devices"
fdc: Deprecate configuring floppies with -global isa-fdc
fdc: Open-code fdctrl_init_isa()
fdc: Reject clash between -drive if=floppy and -global isa-fdc
iotests/172: Cover -global floppy.drive=...
iotests/172: Cover empty filename and multiple use of drives
iotests/172: Include "info block" in test output
Ani Sinha [Tue, 16 Jun 2020 12:31:39 +0000 (12:31 +0000)]
Rename use_acpi_pci_hotplug to more appropriate use_acpi_hotplug_bridge
Currently, the option use_acpi_pci_hotplug is being used to control device
hotplug capability using ACPI for slots of cold plugged bridges. Hence, we
are renaming this option to better reflect what it actually does.
Prior to this change, the vhost_user_fill_msg_region function filled out
all elements of the VhostUserMemoryRegion struct except the mmap_offset.
This function is often called on uninitialized structs, which are then
copied into VHOST_USER_SET_MEM_TABLE and VHOST_USER_ADD/REM_MEM_REG
messages. In some cases, where the mmap_offset was not needed, it was
left uninitialized, causing QEMU to send the backend uninitialized data,
which Coverity flagged as a series of issues.
This change augments the vhost_user_fill_msg_region API, adding a
mmap_offset paramenter, forcing the caller to initialize mmap_offset.
Eric Auger [Mon, 22 Jun 2020 14:06:19 +0000 (16:06 +0200)]
arm/acpi: Add the TPM2.0 device under the DSDT
In case it is dynamically instantiated, add the TPM 2.0 device object
under the DSDT table in the ACPI namespace. Its HID is MSFT0101
while its current resource settings (CRS) property is initialized
with the guest physical address and MMIO size of the device.
Peter Maydell [Wed, 24 Jun 2020 20:19:53 +0000 (21:19 +0100)]
Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2020-06-23-1' into staging
Merge tpm 2020/06/23 v1
# gpg: Signature made Tue 23 Jun 2020 12:35:03 BST
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <[email protected]>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* remotes/stefanberger/tags/pull-tpm-2020-06-23-1:
tpm: Move backend code under the 'backends/' directory
hw/tpm: Make 'tpm_util.h' publicly accessible as "sysemu/tpm_util.h"
hw/tpm: Move DEFINE_PROP_TPMBE() macro to 'tmp_prop.h' local header
hw/tpm: Move few declarations from 'tpm_util.h' to 'tpm_int.h'
hw/tpm: Make TRACE_TPM_UTIL_SHOW_BUFFER check local to tpm_util.c
hw/tpm: Remove unnecessary 'tpm_int.h' header inclusion
hw/tpm: Move 'hw/acpi/tpm.h' inclusion from header to sources
hw/tpm: Include missing 'qemu/option.h' header
hw/tpm: Do not include 'qemu/osdep.h' in header
hw/tpm: Rename TPMDEV as TPM_BACKEND in Kconfig
backends: Add TPM files into their own directory
docs/specs/tpm: Correct header path name
st_set_trace_file() accidentally enables tracing. It's called
unconditionally during startup, which is why QEMU built with the
simple trace backend always writes a trace file "trace-$PID".
This has been broken for quite a while. I didn't track down the exact
commit.
There is an effort in progress to generate a QEMU Python
package. As I'm not sure this old email is still valid,
update it to not produce package with broken maintainer
email.
Peter Maydell [Tue, 23 Jun 2020 17:57:05 +0000 (18:57 +0100)]
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20200623' into staging
target-arm queue:
* util/oslib-posix : qemu_init_exec_dir implementation for Mac
* target/arm: Last parts of neon decodetree conversion
* hw/arm/virt: Add 5.0 HW compat props
* hw/watchdog/cmsdk-apb-watchdog: Add trace event for lock status
* mps2: Add CMSDK APB watchdog, FPGAIO block, S2I devices and I2C devices
* mps2: Add some unimplemented-device stubs for audio and GPIO
* mps2-tz: Use the ARM SBCon two-wire serial bus interface
* target/arm: Check supported KVM features globally (not per vCPU)
* tests/qtest/arm-cpu-features: Add feature setting tests
* arm/virt: Add memory hot remove support
* remotes/pmaydell/tags/pull-target-arm-20200623: (42 commits)
arm/virt: Add memory hot remove support
tests/qtest/arm-cpu-features: Add feature setting tests
target/arm: Check supported KVM features globally (not per vCPU)
hw/arm/mps2-tz: Use the ARM SBCon two-wire serial bus interface
hw/arm/mps2: Add audio I2S interface as unimplemented device
hw/arm/mps2: Add I2C devices
hw/arm/mps2: Add SPI devices
hw/arm/mps2: Map the FPGA I/O block
hw/arm/mps2: Add CMSDK AHB GPIO peripherals as unimplemented devices
hw/arm/mps2: Add CMSDK APB watchdog device
hw/arm/mps2: Rename CMSDK AHB peripheral region
hw/arm/mps2: Document CMSDK/FPGA APB subsystem sections
hw/arm: Use TYPE_VERSATILE_I2C instead of hardcoded string
hw/i2c: Add header for ARM SBCon two-wire serial bus interface
hw/i2c/versatile_i2c: Add SCL/SDA definitions
hw/i2c/versatile_i2c: Add definitions for register addresses
hw/watchdog/cmsdk-apb-watchdog: Add trace event for lock status
target/arm: Remove dead code relating to SABA and UABA
target/arm: Remove unnecessary gen_io_end() calls
target/arm: Move some functions used only in translate-neon.inc.c to that file
...
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
milkymist_memcard_realize() is wrong that way: it passes &err to
qdev_prop_set_drive_err() and qdev_realize_and_unref(). Currently
harmless, because the latter uses it only as first argument of
error_propagate().
Making qdev_prop_set_drive_err() fail involves abuse of -global.
Leave handling that to qdev_prop_set_drive(), like we do elsewhere.
sd/pxa2xx_mmci: Don't crash on pxa2xx_mmci_init() error
On error, pxa2xx_mmci_init() reports to stderr and returns NULL.
Callers don't check for errors. Machines akita, borzoi, mainstone,
spitz, terrier, tosa, and z2 crash shortly after, like this:
$ qemu-system-aarch64 -M akita -drive if=sd,readonly=on
qemu-system-aarch64: failed to init SD card: Cannot use read-only drive as SD card
Segmentation fault (core dumped)
Machines connex and verdex reach the check for orphaned drives first:
$ aarch64-softmmu/qemu-system-aarch64 -M connex -drive if=sd,readonly=on -accel qtest
qemu-system-aarch64: failed to init SD card: Cannot use read-only drive as SD card
qemu-system-aarch64: -drive if=sd,readonly=on: machine type does not support if=sd,bus=0,unit=0
qdev_prop_set_chr() screws up when the property already has a non-null
value: it neglects to release the old value. Both the old and the new
backend become attached to the same device. Unlike for block devices
(see previous commit), this can't be observed from the monitor (I
think).
Special case: attempting to use the same backend both times crashes:
$ qemu-system-x86_64 --nodefaults -serial null -global isa-serial.chardev=serial0
Unexpected error in qemu_chr_fe_init() at /work/armbru/qemu/chardev/char-fe.c:220:
qemu-system-x86_64: Device 'serial0' is in use
Aborted (core dumped)
Yet another example: -device with multiple chardev=... (but not
device_add, which silently drops all but the last duplicate property).
Perhaps chardev property override could be made to work. Perhaps it
should. I can't afford the time to figure this out now. What I can
do reject usage that leaves backends in unhealthy states. For what
it's worth, we've long done the same for netdev properties.
qdev_prop_set_drive() screws up when the property already has a
non-null value: it neglects to release the old value. Both the old
and the new backend become attached to the same device.
Example (taken from iotest 172): -fda ... -drive if=none,... -global
floppy.drive=none0.
Special case: attempting to use the same backend both times fails.
Example (also from iotest 172): -fda ... -global floppy.drive=floppy0.
Yet another example: -device with multiple drive=... (but not
device_add, which silently drops all but the last duplicate property).
Perhaps drive property override could be made to work. Perhaps it
should. I can't afford the time to figure this out now. What I can
do is reject usage that leaves backends in unhealthy states. For what
it's worth, we've long done the same for netdev properties.
qdev: Improve netdev property override error a bit
qdev_prop_set_netdev() fails when the property already has a non-null
value. Seems to go back to commit 30c367ed44
"qdev-properties-system.c: Allow vlan or netdev for -device, not
both", v1.7.0. Board code doesn't expect failure, and crashes:
$ qemu-system-x86_64 --nodefaults -nic user -netdev user,id=nic0 -global e1000.netdev=nic0
Unexpected error in error_set_from_qdev_prop_error() at /work/armbru/qemu/hw/core/qdev-properties.c:1101:
qemu-system-x86_64: Property 'e1000.netdev' doesn't take value '__org.qemu.nic0
'
Aborted (core dumped)
-device and device_add handle the failure:
$ qemu-system-x86_64 -nodefaults -netdev user,id=net0 -netdev user,id=net1 -device e1000,netdev=net0,netdev=net1
qemu-system-x86_64: -device e1000,netdev=net0,netdev=net1: Property 'e1000.netdev' doesn't take value 'net1'
$ qemu-system-x86_64 -nodefaults -S -display none -monitor stdio -netdev user,id=net0 -netdev user,id=net1 -global e1000.netdev=net0
QEMU 5.0.50 monitor - type 'help' for more information
(qemu) qemu-system-x86_64: warning: netdev net0 has no peer
qemu-system-x86_64: warning: netdev net1 has no peer
device_add e1000,netdev=net1
Error: Property 'e1000.netdev' doesn't take value 'net1'
Perhaps netdev property override could be made to work. Perhaps it
should. I'm not the right guy to figure this out. What I can do is
improve the error message a bit:
(qemu) device_add e1000,netdev=net1
Error: -global e1000.netdev=... conflicts with netdev=net1
We stopped using get_pointer() and set_pointer() for netdev in commit 23120b13c6 "net: don't use set/get_pointer() in set/get_netdev()"
(v2.3.0), and for chardev in commit becdfa00cf "char: replace PROP_CHR
with CharBackend" (v2.8.0). With only the drive user left, they're
not helpful anymore. Eliminate.
blockdev: Deprecate -drive with bogus interface type
Drives with interface types other than if=none are for onboard
devices. Unfortunately, any such drives the board doesn't pick up can
still be used with -device, like this:
$ qemu-system-x86_64 -nodefaults -display none -S -drive if=floppy,id=bogus,unit=7 -device ide-cd,drive=bogus -monitor stdio
QEMU 5.0.50 monitor - type 'help' for more information
(qemu) info block
bogus: [not inserted]
Attached to: /machine/peripheral-anon/device[0]
Removable device: not locked, tray closed
(qemu) info qtree
bus: main-system-bus
type System
[...]
bus: ide.1
type IDE
dev: ide-cd, id ""
---> drive = "bogus"
[...]
unit = 0 (0x0)
[...]
This kind of abuse has always worked. Deprecate it:
qemu-system-x86_64: -drive if=floppy,id=bogus,unit=7: warning: bogus if=floppy is deprecated, use if=none
Helper function fdctrl_init_isa() is less than helpful: one of three
places creating "isa-fdc" devices use it. Open-code it there, and
drop the function.
fdc: Reject clash between -drive if=floppy and -global isa-fdc
The floppy controller devices desugar their drive properties into
floppy devices (since commit a92bd191a4 "fdc: Move qdev properties to
FloppyDrive", v2.8.0). This involves some bad magic in
fdctrl_connect_drives(), and exists for backward compatibility.
The functions for boards to create floppy controller devices
fdctrl_init_isa(), fdctrl_init_sysbus(), and sun4m_fdctrl_init()
desugar -drive if=floppy to these floppy controller drive properties.
If you use both -drive if=floppy (or its -fda / -fdb sugar) and
-global isa-fdc for the same floppy device, -global silently loses the
conflict, and both backends involved end up with the floppy device
frontend attached, as demonstrated by iotest 172 (see commit before
previous). This is wrong.
Desugar -drive if=floppy straight to floppy devices instead, with
helper fdctrl_init_drives(). The conflict now gets rejected cleanly:
first, fdctrl_connect_drives() creates the floppy for the controller's
property, then fdctrl_init_drives() attempts to create the floppy for
-drive if=floppy, but fails because the unit is already in use.
Output of iotest 172 changes in three ways:
1. The clash gets rejected.
2. In one test case, "info qtree" has the floppy devices swapped, and
"info block" has their QOM paths swapped. This is because the
floppy device for -fda now gets created after the one for -global
isa-fdc.driveB.
3. The error message for -global floppy.drive=floppy0 changes. Before
the patch, we set isa-fdc.driveA to -fda's block backend, then
create the floppy device for it, then move the backend from
isa-fdc.driveA to floppy.drive. Floppy creation fails when
applying -global floppy.drive=floppy0, because floppy0 is still
attached to isa-fdc. After the patch, we create the floppy for
-fda, then set its drive property to floppy0. Now floppy creation
succeeds, but setting the drive property fails, because -global
already set it. Yes, this is exasperatingly complicated.
Use of -global to set a default backend for non-singleton devices is a
bad idea. But as long as we permit it, we better test it.
Test output demonstrates we screw up when -global floppy clashes with
-fda or with -device floppy: according to "info qtree", only the
latter backend is attached, but according to "info block", both are.
Here's the clash with -device:
dev: isa-fdc, id ""
[...]
driveA = ""
driveB = ""
[...]
bus: floppy-bus.0
type floppy-bus
dev: floppy, id ""
unit = 0 (0x0)
---> drive = "none1"
[...]
none0 (NODE_NAME): TEST_DIR/t.qcow2 (qcow2)
---> Attached to: /machine/peripheral-anon/device[0]
Cache mode: writeback
none1 (NODE_NAME): TEST_DIR/t.qcow2.2 (qcow2)
---> Attached to: /machine/peripheral-anon/device[0]
Removable device: not locked, tray closed
Cache mode: writeback
/machine/peripheral-anon/device[0] is the floppy created with -device.
Test output further demonstrates the "Drive 'FOO' is already in use
because it has been automatically connected to another device" error
message can be misleading. With '-fda "" -global
floppy.drive=floppy0', it's in use because -global reuses -fda's
backend. There is no other device involved.
The additional output demonstrates we screw up when -global isa-fdc
clashes with -drive if=floppy or its sugared forms: according to "info
qtree", only the latter backend is attached, but according to "info
block", both are. For instance:
Thread 1 "qemu-system-aar" received signal SIGSEGV, Segmentation fault.
0x0000aaaaaae356d0 in kvm_ioctl (s=0x0, type=44547) at accel/kvm/kvm-all.c:2588
2588 ret = ioctl(s->fd, type, arg);
(gdb) bt
#0 0x0000aaaaaae356d0 in kvm_ioctl (s=0x0, type=44547) at accel/kvm/kvm-all.c:2588
#1 0x0000aaaaaae31568 in kvm_check_extension (s=0x0, extension=126) at accel/kvm/kvm-all.c:916
#2 0x0000aaaaaafce254 in kvm_arm_pmu_supported (cpu=0xaaaaac214ab0) at target/arm/kvm.c:213
#3 0x0000aaaaaafc0f94 in arm_set_pmu (obj=0xaaaaac214ab0, value=true, errp=0xffffffffe438) at target/arm/cpu.c:1111
#4 0x0000aaaaab5533ac in property_set_bool (obj=0xaaaaac214ab0, v=0xaaaaac223a80, name=0xaaaaac11a970 "pmu", opaque=0xaaaaac222730, errp=0xffffffffe438) at qom/object.c:2170
#5 0x0000aaaaab5512f0 in object_property_set (obj=0xaaaaac214ab0, v=0xaaaaac223a80, name=0xaaaaac11a970 "pmu", errp=0xffffffffe438) at qom/object.c:1328
#6 0x0000aaaaab551e10 in object_property_parse (obj=0xaaaaac214ab0, string=0xaaaaac11b4c0 "on", name=0xaaaaac11a970 "pmu", errp=0xffffffffe438) at qom/object.c:1561
#7 0x0000aaaaab54ee8c in object_apply_global_props (obj=0xaaaaac214ab0, props=0xaaaaac018e20, errp=0xaaaaabd6fd88 <error_fatal>) at qom/object.c:407
#8 0x0000aaaaab1dd5a4 in qdev_prop_set_globals (dev=0xaaaaac214ab0) at hw/core/qdev-properties.c:1218
#9 0x0000aaaaab1d9fac in device_post_init (obj=0xaaaaac214ab0) at hw/core/qdev.c:1050
...
#15 0x0000aaaaab54f310 in object_initialize_with_type (obj=0xaaaaac214ab0, size=52208, type=0xaaaaabe237f0) at qom/object.c:512
#16 0x0000aaaaab54fa24 in object_new_with_type (type=0xaaaaabe237f0) at qom/object.c:687
#17 0x0000aaaaab54fa80 in object_new (typename=0xaaaaabe23970 "host-arm-cpu") at qom/object.c:702
#18 0x0000aaaaaaf04a74 in machvirt_init (machine=0xaaaaac0a8550) at hw/arm/virt.c:1770
#19 0x0000aaaaab1e8720 in machine_run_board_init (machine=0xaaaaac0a8550) at hw/core/machine.c:1138
#20 0x0000aaaaaaf95394 in qemu_init (argc=5, argv=0xffffffffea58, envp=0xffffffffea88) at softmmu/vl.c:4348
#21 0x0000aaaaaada3f74 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>) at softmmu/main.c:48
This is because in frame #2, cpu->kvm_state is still NULL
(the vCPU is not yet realized).
KVM has a hard requirement of all cores supporting the same
feature set. We only need to check if the accelerator supports
a feature, not each vCPU individually.
Fix by removing the 'CPUState *cpu' argument from the
kvm_arm_<FEATURE>_supported() functions.
hw/arm/mps2-tz: Use the ARM SBCon two-wire serial bus interface
From 'Application Note AN521', chapter 4.7:
The SMM implements four SBCon serial modules:
One SBCon module for use by the Color LCD touch interface.
One SBCon module to configure the audio controller.
Two general purpose SBCon modules, that connect to the
Expansion headers J7 and J8, are intended for use with the
V2C-Shield1 which provide an I2C interface on the headers.
hw/i2c: Add header for ARM SBCon two-wire serial bus interface
'ARM SBCon two-wire serial bus interface' is the official
name describing the pair of registers used to bitbanging
I2C in the Versatile boards.
Make the private VersatileI2CState structure as public
ArmSbconI2CState.
Add the TYPE_ARM_SBCON_I2C, alias to our current
TYPE_VERSATILE_I2C model.
Rename the memory region description as 'arm_sbcon_i2c'.
Peter Maydell [Fri, 19 Jun 2020 17:15:47 +0000 (18:15 +0100)]
target/arm: Remove dead code relating to SABA and UABA
In commit cfdb2c0c95ae9205b0 ("target/arm: Vectorize SABA/UABA") we
replaced the old handling of SABA/UABA with a vectorized implementation
which returns early rather than falling into the loop-ever-elements
code. We forgot to delete the part of the old looping code that
did the accumulate step, and Coverity correctly warns (CID 1428955)
that this code is now dead. Delete it.
Peter Maydell [Fri, 19 Jun 2020 17:03:24 +0000 (18:03 +0100)]
target/arm: Remove unnecessary gen_io_end() calls
Since commit ba3e7926691ed3 it has been unnecessary for target code
to call gen_io_end() after an IO instruction in icount mode; it is
sufficient to call gen_io_start() before it and to force the end of
the TB.
Many now-unnecessary calls to gen_io_end() were removed in commit 9e9b10c6491153b, but some were missed or accidentally added later.
Remove unneeded calls from the arm target:
* the call in the handling of exception-return-via-LDM is
unnecessary, and the code is already forcing end-of-TB
* the call in the VFP access check code is more complicated:
we weren't ending the TB, so we need to add the code to
force that by setting DISAS_UPDATE
* the doc comment for ARM_CP_IO doesn't need to mention
gen_io_end() any more
Peter Maydell [Tue, 16 Jun 2020 17:08:44 +0000 (18:08 +0100)]
target/arm: Move some functions used only in translate-neon.inc.c to that file
The functions neon_element_offset(), neon_load_element(),
neon_load_element64(), neon_store_element() and
neon_store_element64() are used only in the translate-neon.inc.c
file, so move their definitions there.
Since the .inc.c file is #included in translate.c this doesn't make
much difference currently, but it's a more logical place to put the
functions and it might be helpful if we ever decide to try to make
the .inc.c files genuinely separate compilation units.
Peter Maydell [Tue, 16 Jun 2020 17:08:43 +0000 (18:08 +0100)]
target/arm: Convert Neon VTRN to decodetree
Convert the Neon VTRN insn to decodetree. This is the last insn in the
Neon data-processing group, so we can remove all the now-unused old
decoder framework.
It's possible that there's a more efficient implementation of
VTRN, but for this conversion we just copy the existing approach.
Peter Maydell [Tue, 16 Jun 2020 17:08:42 +0000 (18:08 +0100)]
target/arm: Convert Neon VSWP to decodetree
Convert the Neon VSWP insn to decodetree. Since the new implementation
doesn't have to share a pass-loop with the other 2-reg-misc operations
we can implement the swap with 64-bit accesses rather than 32-bits
(which brings us into line with the pseudocode and is more efficient).
Peter Maydell [Tue, 16 Jun 2020 17:08:40 +0000 (18:08 +0100)]
target/arm: Convert Neon 2-reg-misc VRINT insns to decodetree
Convert the Neon 2-reg-misc VRINT insns to decodetree.
Giving these insns their own do_vrint() function allows us
to change the rounding mode just once at the start and end
rather than doing it for every element in the vector.
Peter Maydell [Tue, 16 Jun 2020 17:08:37 +0000 (18:08 +0100)]
target/arm: Convert Neon VQABS, VQNEG to decodetree
Convert the Neon VQABS and VQNEG insns to decodetree.
Since these are the only ones which need cpu_env passing to
the helper, we wrap the helper rather than creating a whole
new do_2misc_env() function.
Peter Maydell [Tue, 16 Jun 2020 17:08:34 +0000 (18:08 +0100)]
target/arm: Make gen_swap_half() take separate src and dest
Make gen_swap_half() take a source and destination TCGv_i32 rather
than modifying the input TCGv_i32; we're going to want to be able to
use it with the more flexible function signature, and this also
brings it into line with other functions like gen_rev16() and
gen_revsh().
Peter Maydell [Tue, 16 Jun 2020 17:08:32 +0000 (18:08 +0100)]
target/arm: Rename NeonGenOneOpFn to NeonGenOne64OpFn
The NeonGenOneOpFn typedef breaks with the pattern of the other
NeonGen*Fn typedefs, because it is a TCGv_i64 -> TCGv_i64 operation
but it does not have '64' in its name. Rename it to NeonGenOne64OpFn,
so that the old name is available for a TCGv_i32 -> TCGv_i32 operation
(which we will need in a subsequent commit).
projects / qemu.git / log