ide: Reject invalid CHS geometry

[qemu.git] / hw / cirrus_vga.c

diff --git a/hw/cirrus_vga.c b/hw/cirrus_vga.c
index 1703c629e446cb1500bb3fac15c0bd8ffd765be2..ba4828996ab4344f07c06da7979d2d5ecb29ee45 100644 (file)
--- a/hw/cirrus_vga.c
+++ b/hw/cirrus_vga.c
@@ -172,40 +172,6 @@
 #define CIRRUS_MMIO_LINEDRAW_MODE     0x39     // byte
 #define CIRRUS_MMIO_BLTSTATUS         0x40     // byte
 
-// PCI 0x04: command(word), 0x06(word): status
-#define PCI_COMMAND_IOACCESS                0x0001
-#define PCI_COMMAND_MEMACCESS               0x0002
-#define PCI_COMMAND_BUSMASTER               0x0004
-#define PCI_COMMAND_SPECIALCYCLE            0x0008
-#define PCI_COMMAND_MEMWRITEINVALID         0x0010
-#define PCI_COMMAND_PALETTESNOOPING         0x0020
-#define PCI_COMMAND_PARITYDETECTION         0x0040
-#define PCI_COMMAND_ADDRESSDATASTEPPING     0x0080
-#define PCI_COMMAND_BACKTOBACKTRANS         0x0200
-// PCI 0x08, 0xff000000 (0x09-0x0b:class,0x08:rev)
-#define PCI_CLASS_BASE_DISPLAY        0x03
-// PCI 0x08, 0x00ff0000
-#define PCI_CLASS_SUB_VGA             0x00
-// PCI 0x0c, 0x00ff0000 (0x0c:cacheline,0x0d:latency,0x0e:headertype,0x0f:Built-in self test)
-// 0x10-0x3f (headertype 00h)
-// PCI 0x10,0x14,0x18,0x1c,0x20,0x24: base address mapping registers
-//   0x10: MEMBASE, 0x14: IOBASE(hard-coded in XFree86 3.x)
-#define PCI_MAP_MEM                 0x0
-#define PCI_MAP_IO                  0x1
-#define PCI_MAP_MEM_ADDR_MASK       (~0xf)
-#define PCI_MAP_IO_ADDR_MASK        (~0x3)
-#define PCI_MAP_MEMFLAGS_32BIT      0x0
-#define PCI_MAP_MEMFLAGS_32BIT_1M   0x1
-#define PCI_MAP_MEMFLAGS_64BIT      0x4
-#define PCI_MAP_MEMFLAGS_CACHEABLE  0x8
-// PCI 0x28: cardbus CIS pointer
-// PCI 0x2c: subsystem vendor id, 0x2e: subsystem id
-// PCI 0x30: expansion ROM base address
-#define PCI_ROMBIOS_ENABLED         0x1
-// PCI 0x34: 0xffffff00=reserved, 0x000000ff=capabilities pointer
-// PCI 0x38: reserved
-// PCI 0x3c: 0x3c=int-line, 0x3d=int-pin, 0x3e=min-gnt, 0x3f=maax-lat
-
 #define CIRRUS_PNPMMIO_SIZE         0x1000
 
 #define ABS(a) ((signed)(a) > 0 ? a : -a)
@@ -2619,9 +2585,11 @@ static void map_linear_vram(CirrusVGAState *s)
 
 static void unmap_linear_vram(CirrusVGAState *s)
 {
-    if (s->vga.map_addr && s->vga.lfb_addr && s->vga.lfb_end)
+    if (s->vga.map_addr && s->vga.lfb_addr && s->vga.lfb_end) {
         s->vga.map_addr = s->vga.map_end = 0;
-
+         cpu_register_physical_memory(s->vga.lfb_addr, s->vga.vram_size,
+                                      s->cirrus_linear_io_addr);
+    }
     cpu_register_physical_memory(isa_mem_base + 0xa0000, 0x20000,
                                  s->vga.vga_io_memory);
 }
@@ -3017,7 +2985,6 @@ static const VMStateDescription vmstate_pci_cirrus_vga = {
     .version_id = 2,
     .minimum_version_id = 2,
     .minimum_version_id_old = 2,
-    .post_load = cirrus_post_load,
     .fields      = (VMStateField []) {
         VMSTATE_PCI_DEVICE(dev, PCICirrusVGAState),
         VMSTATE_STRUCT(cirrus_vga, PCICirrusVGAState, 0,
@@ -3232,7 +3199,6 @@ static int pci_cirrus_vga_initfn(PCIDevice *dev)
      pci_config_set_vendor_id(pci_conf, PCI_VENDOR_ID_CIRRUS);
      pci_config_set_device_id(pci_conf, device_id);
      pci_config_set_class(pci_conf, PCI_CLASS_DISPLAY_VGA);
-     pci_conf[PCI_HEADER_TYPE] = PCI_HEADER_TYPE_NORMAL;
 
      /* setup memory space */
      /* memory #0 LFB */
@@ -3244,22 +3210,21 @@ static int pci_cirrus_vga_initfn(PCIDevice *dev)
          pci_register_bar((PCIDevice *)d, 1, CIRRUS_PNPMMIO_SIZE,
                           PCI_BASE_ADDRESS_SPACE_MEMORY, cirrus_pci_mmio_map);
      }
-
-     /* ROM BIOS */
-     rom_add_vga(VGABIOS_CIRRUS_FILENAME);
      return 0;
 }
 
 void pci_cirrus_vga_init(PCIBus *bus)
 {
-    pci_create_simple(bus, -1, "Cirrus VGA");
+    pci_create_simple(bus, -1, "cirrus-vga");
 }
 
 static PCIDeviceInfo cirrus_vga_info = {
-    .qdev.name    = "Cirrus VGA",
+    .qdev.name    = "cirrus-vga",
+    .qdev.desc    = "Cirrus CLGD 54xx VGA",
     .qdev.size    = sizeof(PCICirrusVGAState),
     .qdev.vmsd    = &vmstate_pci_cirrus_vga,
     .init         = pci_cirrus_vga_initfn,
+    .romfile      = VGABIOS_CIRRUS_FILENAME,
     .config_write = pci_cirrus_write_config,
 };