[qemu.git] / hw / usb-serial.c

/*
 * FTDI FT232BM Device emulation
 *
 * Copyright (c) 2006 CodeSourcery.
 * Copyright (c) 2008 Samuel Thibault <[email protected]>
 * Written by Paul Brook, reused for FTDI by Samuel Thibault
 *
 * This code is licenced under the LGPL.
 */

#include "qemu-common.h"
#include "qemu-error.h"
#include "usb.h"
#include "usb-desc.h"
#include "qemu-char.h"

//#define DEBUG_Serial

#ifdef DEBUG_Serial
#define DPRINTF(fmt, ...) \
do { printf("usb-serial: " fmt , ## __VA_ARGS__); } while (0)
#else
#define DPRINTF(fmt, ...) do {} while(0)
#endif

#define RECV_BUF 384

/* Commands */
#define FTDI_RESET		0
#define FTDI_SET_MDM_CTRL	1
#define FTDI_SET_FLOW_CTRL	2
#define FTDI_SET_BAUD		3
#define FTDI_SET_DATA		4
#define FTDI_GET_MDM_ST		5
#define FTDI_SET_EVENT_CHR	6
#define FTDI_SET_ERROR_CHR	7
#define FTDI_SET_LATENCY	9
#define FTDI_GET_LATENCY	10

#define DeviceOutVendor	((USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_DEVICE)<<8)
#define DeviceInVendor	((USB_DIR_IN |USB_TYPE_VENDOR|USB_RECIP_DEVICE)<<8)

/* RESET */

#define FTDI_RESET_SIO	0
#define FTDI_RESET_RX	1
#define FTDI_RESET_TX	2

/* SET_MDM_CTRL */

#define FTDI_DTR	1
#define FTDI_SET_DTR	(FTDI_DTR << 8)
#define FTDI_RTS	2
#define FTDI_SET_RTS	(FTDI_RTS << 8)

/* SET_FLOW_CTRL */

#define FTDI_RTS_CTS_HS		1
#define FTDI_DTR_DSR_HS		2
#define FTDI_XON_XOFF_HS	4

/* SET_DATA */

#define FTDI_PARITY	(0x7 << 8)
#define FTDI_ODD	(0x1 << 8)
#define FTDI_EVEN	(0x2 << 8)
#define FTDI_MARK	(0x3 << 8)
#define FTDI_SPACE	(0x4 << 8)

#define FTDI_STOP	(0x3 << 11)
#define FTDI_STOP1	(0x0 << 11)
#define FTDI_STOP15	(0x1 << 11)
#define FTDI_STOP2	(0x2 << 11)

/* GET_MDM_ST */
/* TODO: should be sent every 40ms */
#define FTDI_CTS  (1<<4)        // CTS line status
#define FTDI_DSR  (1<<5)        // DSR line status
#define FTDI_RI   (1<<6)        // RI line status
#define FTDI_RLSD (1<<7)        // Receive Line Signal Detect

/* Status */

#define FTDI_DR   (1<<0)        // Data Ready
#define FTDI_OE   (1<<1)        // Overrun Err
#define FTDI_PE   (1<<2)        // Parity Err
#define FTDI_FE   (1<<3)        // Framing Err
#define FTDI_BI   (1<<4)        // Break Interrupt
#define FTDI_THRE (1<<5)        // Transmitter Holding Register
#define FTDI_TEMT (1<<6)        // Transmitter Empty
#define FTDI_FIFO (1<<7)        // Error in FIFO

typedef struct {
    USBDevice dev;
    uint8_t recv_buf[RECV_BUF];
    uint16_t recv_ptr;
    uint16_t recv_used;
    uint8_t event_chr;
    uint8_t error_chr;
    uint8_t event_trigger;
    QEMUSerialSetParams params;
    int latency;        /* ms */
    CharDriverState *cs;
} USBSerialState;

enum {
    STR_MANUFACTURER = 1,
    STR_PRODUCT_SERIAL,
    STR_PRODUCT_BRAILLE,
    STR_SERIALNUMBER,
};

static const USBDescStrings desc_strings = {
    [STR_MANUFACTURER]    = "QEMU " QEMU_VERSION,
    [STR_PRODUCT_SERIAL]  = "QEMU USB SERIAL",
    [STR_PRODUCT_BRAILLE] = "QEMU USB BRAILLE",
    [STR_SERIALNUMBER]    = "1",
};

static const USBDescIface desc_iface0 = {
    .bInterfaceNumber              = 0,
    .bNumEndpoints                 = 2,
    .bInterfaceClass               = 0xff,
    .bInterfaceSubClass            = 0xff,
    .bInterfaceProtocol            = 0xff,
    .eps = (USBDescEndpoint[]) {
        {
            .bEndpointAddress      = USB_DIR_IN | 0x01,
            .bmAttributes          = USB_ENDPOINT_XFER_BULK,
            .wMaxPacketSize        = 64,
        },{
            .bEndpointAddress      = USB_DIR_OUT | 0x02,
            .bmAttributes          = USB_ENDPOINT_XFER_BULK,
            .wMaxPacketSize        = 64,
        },
    }
};

static const USBDescDevice desc_device = {
    .bcdUSB                        = 0x0200,
    .bMaxPacketSize0               = 8,
    .bNumConfigurations            = 1,
    .confs = (USBDescConfig[]) {
        {
            .bNumInterfaces        = 1,
            .bConfigurationValue   = 1,
            .bmAttributes          = 0x80,
            .bMaxPower             = 50,
            .nif = 1,
            .ifs = &desc_iface0,
        },
    },
};

static const USBDesc desc_serial = {
    .id = {
        .idVendor          = 0x0403,
        .idProduct         = 0x6001,
        .bcdDevice         = 0x0400,
        .iManufacturer     = STR_MANUFACTURER,
        .iProduct          = STR_PRODUCT_SERIAL,
        .iSerialNumber     = STR_SERIALNUMBER,
    },
    .full = &desc_device,
    .str  = desc_strings,
};

static const USBDesc desc_braille = {
    .id = {
        .idVendor          = 0x0403,
        .idProduct         = 0xfe72,
        .bcdDevice         = 0x0400,
        .iManufacturer     = STR_MANUFACTURER,
        .iProduct          = STR_PRODUCT_BRAILLE,
        .iSerialNumber     = STR_SERIALNUMBER,
    },
    .full = &desc_device,
    .str  = desc_strings,
};

static void usb_serial_reset(USBSerialState *s)
{
    /* TODO: Set flow control to none */
    s->event_chr = 0x0d;
    s->event_trigger = 0;
    s->recv_ptr = 0;
    s->recv_used = 0;
    /* TODO: purge in char driver */
}

static void usb_serial_handle_reset(USBDevice *dev)
{
    USBSerialState *s = (USBSerialState *)dev;

    DPRINTF("Reset\n");

    usb_serial_reset(s);
    /* TODO: Reset char device, send BREAK? */
}

static uint8_t usb_get_modem_lines(USBSerialState *s)
{
    int flags;
    uint8_t ret;

    if (qemu_chr_ioctl(s->cs, CHR_IOCTL_SERIAL_GET_TIOCM, &flags) == -ENOTSUP)
        return FTDI_CTS|FTDI_DSR|FTDI_RLSD;

    ret = 0;
    if (flags & CHR_TIOCM_CTS)
        ret |= FTDI_CTS;
    if (flags & CHR_TIOCM_DSR)
        ret |= FTDI_DSR;
    if (flags & CHR_TIOCM_RI)
        ret |= FTDI_RI;
    if (flags & CHR_TIOCM_CAR)
        ret |= FTDI_RLSD;

    return ret;
}

static int usb_serial_handle_control(USBDevice *dev, USBPacket *p,
               int request, int value, int index, int length, uint8_t *data)
{
    USBSerialState *s = (USBSerialState *)dev;
    int ret;

    DPRINTF("got control %x, value %x\n",request, value);
    ret = usb_desc_handle_control(dev, p, request, value, index, length, data);
    if (ret >= 0) {
        return ret;
    }

    ret = 0;
    switch (request) {
    case DeviceRequest | USB_REQ_GET_INTERFACE:
        data[0] = 0;
        ret = 1;
        break;
    case InterfaceOutRequest | USB_REQ_SET_INTERFACE:
        ret = 0;
        break;
    case EndpointOutRequest | USB_REQ_CLEAR_FEATURE:
        ret = 0;
        break;

        /* Class specific requests.  */
    case DeviceOutVendor | FTDI_RESET:
        switch (value) {
        case FTDI_RESET_SIO:
            usb_serial_reset(s);
            break;
        case FTDI_RESET_RX:
            s->recv_ptr = 0;
            s->recv_used = 0;
            /* TODO: purge from char device */
            break;
        case FTDI_RESET_TX:
            /* TODO: purge from char device */
            break;
        }
        break;
    case DeviceOutVendor | FTDI_SET_MDM_CTRL:
    {
        static int flags;
        qemu_chr_ioctl(s->cs,CHR_IOCTL_SERIAL_GET_TIOCM, &flags);
        if (value & FTDI_SET_RTS) {
            if (value & FTDI_RTS)
                flags |= CHR_TIOCM_RTS;
            else
                flags &= ~CHR_TIOCM_RTS;
        }
        if (value & FTDI_SET_DTR) {
            if (value & FTDI_DTR)
                flags |= CHR_TIOCM_DTR;
            else
                flags &= ~CHR_TIOCM_DTR;
        }
        qemu_chr_ioctl(s->cs,CHR_IOCTL_SERIAL_SET_TIOCM, &flags);
        break;
    }
    case DeviceOutVendor | FTDI_SET_FLOW_CTRL:
        /* TODO: ioctl */
        break;
    case DeviceOutVendor | FTDI_SET_BAUD: {
        static const int subdivisors8[8] = { 0, 4, 2, 1, 3, 5, 6, 7 };
        int subdivisor8 = subdivisors8[((value & 0xc000) >> 14)
                                     | ((index & 1) << 2)];
        int divisor = value & 0x3fff;

        /* chip special cases */
        if (divisor == 1 && subdivisor8 == 0)
            subdivisor8 = 4;
        if (divisor == 0 && subdivisor8 == 0)
            divisor = 1;

        s->params.speed = (48000000 / 2) / (8 * divisor + subdivisor8);
        qemu_chr_ioctl(s->cs, CHR_IOCTL_SERIAL_SET_PARAMS, &s->params);
        break;
    }
    case DeviceOutVendor | FTDI_SET_DATA:
        switch (value & FTDI_PARITY) {
            case 0:
                s->params.parity = 'N';
                break;
            case FTDI_ODD:
                s->params.parity = 'O';
                break;
            case FTDI_EVEN:
                s->params.parity = 'E';
                break;
            default:
                DPRINTF("unsupported parity %d\n", value & FTDI_PARITY);
                goto fail;
        }
        switch (value & FTDI_STOP) {
            case FTDI_STOP1:
                s->params.stop_bits = 1;
                break;
            case FTDI_STOP2:
                s->params.stop_bits = 2;
                break;
            default:
                DPRINTF("unsupported stop bits %d\n", value & FTDI_STOP);
                goto fail;
        }
        qemu_chr_ioctl(s->cs, CHR_IOCTL_SERIAL_SET_PARAMS, &s->params);
        /* TODO: TX ON/OFF */
        break;
    case DeviceInVendor | FTDI_GET_MDM_ST:
        data[0] = usb_get_modem_lines(s) | 1;
        data[1] = 0;
        ret = 2;
        break;
    case DeviceOutVendor | FTDI_SET_EVENT_CHR:
        /* TODO: handle it */
        s->event_chr = value;
        break;
    case DeviceOutVendor | FTDI_SET_ERROR_CHR:
        /* TODO: handle it */
        s->error_chr = value;
        break;
    case DeviceOutVendor | FTDI_SET_LATENCY:
        s->latency = value;
        break;
    case DeviceInVendor | FTDI_GET_LATENCY:
        data[0] = s->latency;
        ret = 1;
        break;
    default:
    fail:
        DPRINTF("got unsupported/bogus control %x, value %x\n", request, value);
        ret = USB_RET_STALL;
        break;
    }
    return ret;
}

static int usb_serial_handle_data(USBDevice *dev, USBPacket *p)
{
    USBSerialState *s = (USBSerialState *)dev;
    int ret = 0;
    uint8_t devep = p->devep;
    uint8_t *data = p->data;
    int len = p->len;
    int first_len;

    switch (p->pid) {
    case USB_TOKEN_OUT:
        if (devep != 2)
            goto fail;
        qemu_chr_write(s->cs, data, len);
        break;

    case USB_TOKEN_IN:
        if (devep != 1)
            goto fail;
        first_len = RECV_BUF - s->recv_ptr;
        if (len <= 2) {
            ret = USB_RET_NAK;
            break;
        }
        *data++ = usb_get_modem_lines(s) | 1;
        /* We do not have the uart details */
        /* handle serial break */
        if (s->event_trigger && s->event_trigger & FTDI_BI) {
            s->event_trigger &= ~FTDI_BI;
            *data = FTDI_BI;
            ret = 2;
            break;
        } else {
            *data++ = 0;
        }
        len -= 2;
        if (len > s->recv_used)
            len = s->recv_used;
        if (!len) {
            ret = USB_RET_NAK;
            break;
        }
        if (first_len > len)
            first_len = len;
        memcpy(data, s->recv_buf + s->recv_ptr, first_len);
        if (len > first_len)
            memcpy(data + first_len, s->recv_buf, len - first_len);
        s->recv_used -= len;
        s->recv_ptr = (s->recv_ptr + len) % RECV_BUF;
        ret = len + 2;
        break;

    default:
        DPRINTF("Bad token\n");
    fail:
        ret = USB_RET_STALL;
        break;
    }

    return ret;
}

static void usb_serial_handle_destroy(USBDevice *dev)
{
    USBSerialState *s = (USBSerialState *)dev;

    qemu_chr_close(s->cs);
}

static int usb_serial_can_read(void *opaque)
{
    USBSerialState *s = opaque;
    return RECV_BUF - s->recv_used;
}

static void usb_serial_read(void *opaque, const uint8_t *buf, int size)
{
    USBSerialState *s = opaque;
    int first_size, start;

    /* room in the buffer? */
    if (size > (RECV_BUF - s->recv_used))
        size = RECV_BUF - s->recv_used;

    start = s->recv_ptr + s->recv_used;
    if (start < RECV_BUF) {
        /* copy data to end of buffer */
        first_size = RECV_BUF - start;
        if (first_size > size)
            first_size = size;

        memcpy(s->recv_buf + start, buf, first_size);

        /* wrap around to front if needed */
        if (size > first_size)
            memcpy(s->recv_buf, buf + first_size, size - first_size);
    } else {
        start -= RECV_BUF;
        memcpy(s->recv_buf + start, buf, size);
    }
    s->recv_used += size;
}

static void usb_serial_event(void *opaque, int event)
{
    USBSerialState *s = opaque;

    switch (event) {
        case CHR_EVENT_BREAK:
            s->event_trigger |= FTDI_BI;
            break;
        case CHR_EVENT_FOCUS:
            break;
        case CHR_EVENT_OPENED:
            usb_serial_reset(s);
            /* TODO: Reset USB port */
            break;
    }
}

static int usb_serial_initfn(USBDevice *dev)
{
    USBSerialState *s = DO_UPCAST(USBSerialState, dev, dev);

    usb_desc_init(dev);

    if (!s->cs) {
        error_report("Property chardev is required");
        return -1;
    }

    qemu_chr_add_handlers(s->cs, usb_serial_can_read, usb_serial_read,
                          usb_serial_event, s);
    usb_serial_handle_reset(dev);
    return 0;
}

static USBDevice *usb_serial_init(const char *filename)
{
    USBDevice *dev;
    CharDriverState *cdrv;
    uint32_t vendorid = 0, productid = 0;
    char label[32];
    static int index;

    while (*filename && *filename != ':') {
        const char *p;
        char *e;
        if (strstart(filename, "vendorid=", &p)) {
            vendorid = strtol(p, &e, 16);
            if (e == p || (*e && *e != ',' && *e != ':')) {
                error_report("bogus vendor ID %s", p);
                return NULL;
            }
            filename = e;
        } else if (strstart(filename, "productid=", &p)) {
            productid = strtol(p, &e, 16);
            if (e == p || (*e && *e != ',' && *e != ':')) {
                error_report("bogus product ID %s", p);
                return NULL;
            }
            filename = e;
        } else {
            error_report("unrecognized serial USB option %s", filename);
            return NULL;
        }
        while(*filename == ',')
            filename++;
    }
    if (!*filename) {
        error_report("character device specification needed");
        return NULL;
    }
    filename++;

    snprintf(label, sizeof(label), "usbserial%d", index++);
    cdrv = qemu_chr_open(label, filename, NULL);
    if (!cdrv)
        return NULL;

    dev = usb_create(NULL /* FIXME */, "usb-serial");
    if (!dev) {
        return NULL;
    }
    qdev_prop_set_chr(&dev->qdev, "chardev", cdrv);
    if (vendorid)
        qdev_prop_set_uint16(&dev->qdev, "vendorid", vendorid);
    if (productid)
        qdev_prop_set_uint16(&dev->qdev, "productid", productid);
    qdev_init_nofail(&dev->qdev);

    return dev;
}

static USBDevice *usb_braille_init(const char *unused)
{
    USBDevice *dev;
    CharDriverState *cdrv;

    cdrv = qemu_chr_open("braille", "braille", NULL);
    if (!cdrv)
        return NULL;

    dev = usb_create(NULL /* FIXME */, "usb-braille");
    qdev_prop_set_chr(&dev->qdev, "chardev", cdrv);
    qdev_init_nofail(&dev->qdev);

    return dev;
}

static struct USBDeviceInfo serial_info = {
    .product_desc   = "QEMU USB Serial",
    .qdev.name      = "usb-serial",
    .qdev.size      = sizeof(USBSerialState),
    .usb_desc       = &desc_serial,
    .init           = usb_serial_initfn,
    .handle_packet  = usb_generic_handle_packet,
    .handle_reset   = usb_serial_handle_reset,
    .handle_control = usb_serial_handle_control,
    .handle_data    = usb_serial_handle_data,
    .handle_destroy = usb_serial_handle_destroy,
    .usbdevice_name = "serial",
    .usbdevice_init = usb_serial_init,
    .qdev.props     = (Property[]) {
        DEFINE_PROP_CHR("chardev", USBSerialState, cs),
        DEFINE_PROP_END_OF_LIST(),
    },
};

static struct USBDeviceInfo braille_info = {
    .product_desc   = "QEMU USB Braille",
    .qdev.name      = "usb-braille",
    .qdev.size      = sizeof(USBSerialState),
    .usb_desc       = &desc_braille,
    .init           = usb_serial_initfn,
    .handle_packet  = usb_generic_handle_packet,
    .handle_reset   = usb_serial_handle_reset,
    .handle_control = usb_serial_handle_control,
    .handle_data    = usb_serial_handle_data,
    .handle_destroy = usb_serial_handle_destroy,
    .usbdevice_name = "braille",
    .usbdevice_init = usb_braille_init,
    .qdev.props     = (Property[]) {
        DEFINE_PROP_CHR("chardev", USBSerialState, cs),
        DEFINE_PROP_END_OF_LIST(),
    },
};

static void usb_serial_register_devices(void)
{
    usb_qdev_register(&serial_info);
    usb_qdev_register(&braille_info);
}
device_init(usb_serial_register_devices)
Commit	Line	Data
a7954218 AZ	1	/*
	2	* FTDI FT232BM Device emulation
	3	*
	4	* Copyright (c) 2006 CodeSourcery.
	5	* Copyright (c) 2008 Samuel Thibault <[email protected]>
	6	* Written by Paul Brook, reused for FTDI by Samuel Thibault
	7	*
	8	* This code is licenced under the LGPL.
	9	*/
	10
	11	#include "qemu-common.h"
2f792016	12	#include "qemu-error.h"
a7954218	13	#include "usb.h"
f29783f7	14	#include "usb-desc.h"
a7954218 AZ	15	#include "qemu-char.h"
	16
	17	//#define DEBUG_Serial
	18
	19	#ifdef DEBUG_Serial
001faf32 BS	20	#define DPRINTF(fmt, ...) \
001faf32 BS	21	do { printf("usb-serial: " fmt , ## __VA_ARGS__); } while (0)
a7954218	22	#else
001faf32	23	#define DPRINTF(fmt, ...) do {} while(0)
a7954218 AZ	24	#endif
	25
	26	#define RECV_BUF 384
a7954218 AZ	27
	28	/* Commands */
	29	#define FTDI_RESET 0
	30	#define FTDI_SET_MDM_CTRL 1
	31	#define FTDI_SET_FLOW_CTRL 2
	32	#define FTDI_SET_BAUD 3
	33	#define FTDI_SET_DATA 4
	34	#define FTDI_GET_MDM_ST 5
	35	#define FTDI_SET_EVENT_CHR 6
	36	#define FTDI_SET_ERROR_CHR 7
	37	#define FTDI_SET_LATENCY 9
	38	#define FTDI_GET_LATENCY 10
	39
	40	#define DeviceOutVendor ((USB_DIR_OUT\|USB_TYPE_VENDOR\|USB_RECIP_DEVICE)<<8)
	41	#define DeviceInVendor ((USB_DIR_IN \|USB_TYPE_VENDOR\|USB_RECIP_DEVICE)<<8)
	42
	43	/* RESET */
	44
	45	#define FTDI_RESET_SIO 0
	46	#define FTDI_RESET_RX 1
	47	#define FTDI_RESET_TX 2
	48
	49	/* SET_MDM_CTRL */
	50
a7954218	51	#define FTDI_DTR 1
abb8a139	52	#define FTDI_SET_DTR (FTDI_DTR << 8)
a7954218	53	#define FTDI_RTS 2
abb8a139	54	#define FTDI_SET_RTS (FTDI_RTS << 8)
a7954218 AZ	55
	56	/* SET_FLOW_CTRL */
	57
	58	#define FTDI_RTS_CTS_HS 1
	59	#define FTDI_DTR_DSR_HS 2
	60	#define FTDI_XON_XOFF_HS 4
	61
	62	/* SET_DATA */
	63
	64	#define FTDI_PARITY (0x7 << 8)
	65	#define FTDI_ODD (0x1 << 8)
	66	#define FTDI_EVEN (0x2 << 8)
	67	#define FTDI_MARK (0x3 << 8)
	68	#define FTDI_SPACE (0x4 << 8)
	69
	70	#define FTDI_STOP (0x3 << 11)
	71	#define FTDI_STOP1 (0x0 << 11)
	72	#define FTDI_STOP15 (0x1 << 11)
	73	#define FTDI_STOP2 (0x2 << 11)
	74
	75	/* GET_MDM_ST */
	76	/* TODO: should be sent every 40ms */
	77	#define FTDI_CTS (1<<4) // CTS line status
	78	#define FTDI_DSR (1<<5) // DSR line status
	79	#define FTDI_RI (1<<6) // RI line status
	80	#define FTDI_RLSD (1<<7) // Receive Line Signal Detect
	81
	82	/* Status */
	83
	84	#define FTDI_DR (1<<0) // Data Ready
	85	#define FTDI_OE (1<<1) // Overrun Err
	86	#define FTDI_PE (1<<2) // Parity Err
	87	#define FTDI_FE (1<<3) // Framing Err
	88	#define FTDI_BI (1<<4) // Break Interrupt
	89	#define FTDI_THRE (1<<5) // Transmitter Holding Register
	90	#define FTDI_TEMT (1<<6) // Transmitter Empty
	91	#define FTDI_FIFO (1<<7) // Error in FIFO
	92
	93	typedef struct {
	94	USBDevice dev;
a7954218	95	uint8_t recv_buf[RECV_BUF];
8109b9b6 AJ	96	uint16_t recv_ptr;
8109b9b6 AJ	97	uint16_t recv_used;
a7954218 AZ	98	uint8_t event_chr;
	99	uint8_t error_chr;
	100	uint8_t event_trigger;
a7954218 AZ	101	QEMUSerialSetParams params;
	102	int latency; /* ms */
	103	CharDriverState *cs;
	104	} USBSerialState;
	105
f29783f7 GH	106	enum {
	107	STR_MANUFACTURER = 1,
	108	STR_PRODUCT_SERIAL,
	109	STR_PRODUCT_BRAILLE,
	110	STR_SERIALNUMBER,
a7954218 AZ	111	};
a7954218 AZ	112
f29783f7 GH	113	static const USBDescStrings desc_strings = {
	114	[STR_MANUFACTURER] = "QEMU " QEMU_VERSION,
	115	[STR_PRODUCT_SERIAL] = "QEMU USB SERIAL",
	116	[STR_PRODUCT_BRAILLE] = "QEMU USB BRAILLE",
	117	[STR_SERIALNUMBER] = "1",
	118	};
	119
	120	static const USBDescIface desc_iface0 = {
	121	.bInterfaceNumber = 0,
	122	.bNumEndpoints = 2,
	123	.bInterfaceClass = 0xff,
	124	.bInterfaceSubClass = 0xff,
	125	.bInterfaceProtocol = 0xff,
	126	.eps = (USBDescEndpoint[]) {
	127	{
	128	.bEndpointAddress = USB_DIR_IN \| 0x01,
	129	.bmAttributes = USB_ENDPOINT_XFER_BULK,
	130	.wMaxPacketSize = 64,
	131	},{
	132	.bEndpointAddress = USB_DIR_OUT \| 0x02,
	133	.bmAttributes = USB_ENDPOINT_XFER_BULK,
	134	.wMaxPacketSize = 64,
	135	},
	136	}
	137	};
	138
	139	static const USBDescDevice desc_device = {
	140	.bcdUSB = 0x0200,
	141	.bMaxPacketSize0 = 8,
	142	.bNumConfigurations = 1,
	143	.confs = (USBDescConfig[]) {
	144	{
	145	.bNumInterfaces = 1,
	146	.bConfigurationValue = 1,
	147	.bmAttributes = 0x80,
	148	.bMaxPower = 50,
add75088	149	.nif = 1,
f29783f7 GH	150	.ifs = &desc_iface0,
	151	},
	152	},
	153	};
	154
	155	static const USBDesc desc_serial = {
	156	.id = {
	157	.idVendor = 0x0403,
	158	.idProduct = 0x6001,
	159	.bcdDevice = 0x0400,
	160	.iManufacturer = STR_MANUFACTURER,
	161	.iProduct = STR_PRODUCT_SERIAL,
	162	.iSerialNumber = STR_SERIALNUMBER,
	163	},
	164	.full = &desc_device,
	165	.str = desc_strings,
	166	};
	167
	168	static const USBDesc desc_braille = {
	169	.id = {
	170	.idVendor = 0x0403,
	171	.idProduct = 0xfe72,
	172	.bcdDevice = 0x0400,
	173	.iManufacturer = STR_MANUFACTURER,
	174	.iProduct = STR_PRODUCT_BRAILLE,
	175	.iSerialNumber = STR_SERIALNUMBER,
	176	},
	177	.full = &desc_device,
	178	.str = desc_strings,
a7954218 AZ	179	};
	180
	181	static void usb_serial_reset(USBSerialState *s)
	182	{
	183	/* TODO: Set flow control to none */
	184	s->event_chr = 0x0d;
	185	s->event_trigger = 0;
	186	s->recv_ptr = 0;
	187	s->recv_used = 0;
	188	/* TODO: purge in char driver */
a7954218 AZ	189	}
	190
	191	static void usb_serial_handle_reset(USBDevice *dev)
	192	{
	193	USBSerialState s = (USBSerialState )dev;
	194
	195	DPRINTF("Reset\n");
	196
	197	usb_serial_reset(s);
	198	/* TODO: Reset char device, send BREAK? */
	199	}
	200
abb8a139 AJ	201	static uint8_t usb_get_modem_lines(USBSerialState *s)
	202	{
	203	int flags;
	204	uint8_t ret;
	205
	206	if (qemu_chr_ioctl(s->cs, CHR_IOCTL_SERIAL_GET_TIOCM, &flags) == -ENOTSUP)
	207	return FTDI_CTS\|FTDI_DSR\|FTDI_RLSD;
	208
	209	ret = 0;
	210	if (flags & CHR_TIOCM_CTS)
	211	ret \|= FTDI_CTS;
	212	if (flags & CHR_TIOCM_DSR)
	213	ret \|= FTDI_DSR;
	214	if (flags & CHR_TIOCM_RI)
	215	ret \|= FTDI_RI;
	216	if (flags & CHR_TIOCM_CAR)
	217	ret \|= FTDI_RLSD;
	218
	219	return ret;
	220	}
	221
007fd62f HG	222	static int usb_serial_handle_control(USBDevice dev, USBPacket p,
007fd62f HG	223	int request, int value, int index, int length, uint8_t *data)
a7954218 AZ	224	{
a7954218 AZ	225	USBSerialState s = (USBSerialState )dev;
f29783f7 GH	226	int ret;
	227
	228	DPRINTF("got control %x, value %x\n",request, value);
007fd62f	229	ret = usb_desc_handle_control(dev, p, request, value, index, length, data);
f29783f7 GH	230	if (ret >= 0) {
	231	return ret;
	232	}
a7954218	233
f29783f7	234	ret = 0;
a7954218	235	switch (request) {
a7954218 AZ	236	case DeviceRequest \| USB_REQ_GET_INTERFACE:
	237	data[0] = 0;
	238	ret = 1;
	239	break;
	240	case InterfaceOutRequest \| USB_REQ_SET_INTERFACE:
	241	ret = 0;
	242	break;
	243	case EndpointOutRequest \| USB_REQ_CLEAR_FEATURE:
	244	ret = 0;
	245	break;
	246
	247	/* Class specific requests. */
	248	case DeviceOutVendor \| FTDI_RESET:
	249	switch (value) {
	250	case FTDI_RESET_SIO:
	251	usb_serial_reset(s);
	252	break;
	253	case FTDI_RESET_RX:
	254	s->recv_ptr = 0;
	255	s->recv_used = 0;
	256	/* TODO: purge from char device */
	257	break;
	258	case FTDI_RESET_TX:
	259	/* TODO: purge from char device */
	260	break;
	261	}
	262	break;
	263	case DeviceOutVendor \| FTDI_SET_MDM_CTRL:
abb8a139 AJ	264	{
	265	static int flags;
	266	qemu_chr_ioctl(s->cs,CHR_IOCTL_SERIAL_GET_TIOCM, &flags);
	267	if (value & FTDI_SET_RTS) {
	268	if (value & FTDI_RTS)
	269	flags \|= CHR_TIOCM_RTS;
	270	else
	271	flags &= ~CHR_TIOCM_RTS;
	272	}
	273	if (value & FTDI_SET_DTR) {
	274	if (value & FTDI_DTR)
	275	flags \|= CHR_TIOCM_DTR;
	276	else
	277	flags &= ~CHR_TIOCM_DTR;
	278	}
	279	qemu_chr_ioctl(s->cs,CHR_IOCTL_SERIAL_SET_TIOCM, &flags);
a7954218	280	break;
abb8a139	281	}
a7954218 AZ	282	case DeviceOutVendor \| FTDI_SET_FLOW_CTRL:
	283	/* TODO: ioctl */
	284	break;
	285	case DeviceOutVendor \| FTDI_SET_BAUD: {
	286	static const int subdivisors8[8] = { 0, 4, 2, 1, 3, 5, 6, 7 };
	287	int subdivisor8 = subdivisors8[((value & 0xc000) >> 14)
	288	\| ((index & 1) << 2)];
	289	int divisor = value & 0x3fff;
	290
	291	/* chip special cases */
	292	if (divisor == 1 && subdivisor8 == 0)
	293	subdivisor8 = 4;
	294	if (divisor == 0 && subdivisor8 == 0)
	295	divisor = 1;
	296
	297	s->params.speed = (48000000 / 2) / (8 * divisor + subdivisor8);
	298	qemu_chr_ioctl(s->cs, CHR_IOCTL_SERIAL_SET_PARAMS, &s->params);
	299	break;
	300	}
	301	case DeviceOutVendor \| FTDI_SET_DATA:
	302	switch (value & FTDI_PARITY) {
	303	case 0:
	304	s->params.parity = 'N';
	305	break;
	306	case FTDI_ODD:
	307	s->params.parity = 'O';
	308	break;
	309	case FTDI_EVEN:
	310	s->params.parity = 'E';
	311	break;
	312	default:
	313	DPRINTF("unsupported parity %d\n", value & FTDI_PARITY);
	314	goto fail;
	315	}
	316	switch (value & FTDI_STOP) {
	317	case FTDI_STOP1:
	318	s->params.stop_bits = 1;
	319	break;
	320	case FTDI_STOP2:
	321	s->params.stop_bits = 2;
	322	break;
	323	default:
	324	DPRINTF("unsupported stop bits %d\n", value & FTDI_STOP);
	325	goto fail;
	326	}
	327	qemu_chr_ioctl(s->cs, CHR_IOCTL_SERIAL_SET_PARAMS, &s->params);
	328	/* TODO: TX ON/OFF */
	329	break;
	330	case DeviceInVendor \| FTDI_GET_MDM_ST:
abb8a139 AJ	331	data[0] = usb_get_modem_lines(s) \| 1;
	332	data[1] = 0;
	333	ret = 2;
a7954218 AZ	334	break;
	335	case DeviceOutVendor \| FTDI_SET_EVENT_CHR:
	336	/* TODO: handle it */
	337	s->event_chr = value;
	338	break;
	339	case DeviceOutVendor \| FTDI_SET_ERROR_CHR:
	340	/* TODO: handle it */
	341	s->error_chr = value;
	342	break;
	343	case DeviceOutVendor \| FTDI_SET_LATENCY:
	344	s->latency = value;
	345	break;
	346	case DeviceInVendor \| FTDI_GET_LATENCY:
	347	data[0] = s->latency;
	348	ret = 1;
	349	break;
	350	default:
	351	fail:
	352	DPRINTF("got unsupported/bogus control %x, value %x\n", request, value);
	353	ret = USB_RET_STALL;
	354	break;
	355	}
	356	return ret;
	357	}
	358
	359	static int usb_serial_handle_data(USBDevice dev, USBPacket p)
	360	{
	361	USBSerialState s = (USBSerialState )dev;
	362	int ret = 0;
	363	uint8_t devep = p->devep;
	364	uint8_t *data = p->data;
	365	int len = p->len;
	366	int first_len;
	367
	368	switch (p->pid) {
	369	case USB_TOKEN_OUT:
	370	if (devep != 2)
	371	goto fail;
	372	qemu_chr_write(s->cs, data, len);
	373	break;
	374
	375	case USB_TOKEN_IN:
	376	if (devep != 1)
	377	goto fail;
	378	first_len = RECV_BUF - s->recv_ptr;
	379	if (len <= 2) {
	380	ret = USB_RET_NAK;
	381	break;
	382	}
abb8a139 AJ	383	*data++ = usb_get_modem_lines(s) \| 1;
abb8a139 AJ	384	/* We do not have the uart details */
7e57f049 JW	385	/* handle serial break */
	386	if (s->event_trigger && s->event_trigger & FTDI_BI) {
	387	s->event_trigger &= ~FTDI_BI;
d4c4e6fd	388	*data = FTDI_BI;
7e57f049 JW	389	ret = 2;
	390	break;
	391	} else {
	392	*data++ = 0;
	393	}
a7954218 AZ	394	len -= 2;
	395	if (len > s->recv_used)
	396	len = s->recv_used;
	397	if (!len) {
	398	ret = USB_RET_NAK;
	399	break;
	400	}
	401	if (first_len > len)
	402	first_len = len;
	403	memcpy(data, s->recv_buf + s->recv_ptr, first_len);
	404	if (len > first_len)
	405	memcpy(data + first_len, s->recv_buf, len - first_len);
	406	s->recv_used -= len;
	407	s->recv_ptr = (s->recv_ptr + len) % RECV_BUF;
	408	ret = len + 2;
	409	break;
	410
	411	default:
	412	DPRINTF("Bad token\n");
	413	fail:
	414	ret = USB_RET_STALL;
	415	break;
	416	}
	417
	418	return ret;
	419	}
	420
	421	static void usb_serial_handle_destroy(USBDevice *dev)
	422	{
	423	USBSerialState s = (USBSerialState )dev;
	424
	425	qemu_chr_close(s->cs);
a7954218 AZ	426	}
a7954218 AZ	427
8fcd3692	428	static int usb_serial_can_read(void *opaque)
a7954218 AZ	429	{
	430	USBSerialState *s = opaque;
	431	return RECV_BUF - s->recv_used;
	432	}
	433
8fcd3692	434	static void usb_serial_read(void opaque, const uint8_t buf, int size)
a7954218 AZ	435	{
a7954218 AZ	436	USBSerialState *s = opaque;
4ab4183d DA	437	int first_size, start;
	438
	439	/* room in the buffer? */
	440	if (size > (RECV_BUF - s->recv_used))
	441	size = RECV_BUF - s->recv_used;
	442
	443	start = s->recv_ptr + s->recv_used;
	444	if (start < RECV_BUF) {
	445	/* copy data to end of buffer */
	446	first_size = RECV_BUF - start;
	447	if (first_size > size)
	448	first_size = size;
	449
	450	memcpy(s->recv_buf + start, buf, first_size);
	451
	452	/* wrap around to front if needed */
	453	if (size > first_size)
	454	memcpy(s->recv_buf, buf + first_size, size - first_size);
	455	} else {
	456	start -= RECV_BUF;
	457	memcpy(s->recv_buf + start, buf, size);
	458	}
a7954218 AZ	459	s->recv_used += size;
	460	}
	461
8fcd3692	462	static void usb_serial_event(void *opaque, int event)
a7954218 AZ	463	{
	464	USBSerialState *s = opaque;
	465
	466	switch (event) {
	467	case CHR_EVENT_BREAK:
7e57f049	468	s->event_trigger \|= FTDI_BI;
a7954218 AZ	469	break;
	470	case CHR_EVENT_FOCUS:
	471	break;
b6b8df56	472	case CHR_EVENT_OPENED:
a7954218 AZ	473	usb_serial_reset(s);
	474	/* TODO: Reset USB port */
	475	break;
	476	}
	477	}
	478
806b6024 GH	479	static int usb_serial_initfn(USBDevice *dev)
	480	{
	481	USBSerialState *s = DO_UPCAST(USBSerialState, dev, dev);
a980a065 GH	482
a980a065 GH	483	usb_desc_init(dev);
2b0efdc3	484
81bf96d3 MA	485	if (!s->cs) {
	486	error_report("Property chardev is required");
	487	return -1;
	488	}
	489
2b0efdc3 GH	490	qemu_chr_add_handlers(s->cs, usb_serial_can_read, usb_serial_read,
	491	usb_serial_event, s);
	492	usb_serial_handle_reset(dev);
806b6024 GH	493	return 0;
	494	}
	495
2b0efdc3	496	static USBDevice usb_serial_init(const char filename)
a7954218	497	{
806b6024	498	USBDevice *dev;
a7954218	499	CharDriverState *cdrv;
2b0efdc3	500	uint32_t vendorid = 0, productid = 0;
5ccfae10 AL	501	char label[32];
5ccfae10 AL	502	static int index;
a7954218 AZ	503
	504	while (filename && filename != ':') {
	505	const char *p;
	506	char *e;
	507	if (strstart(filename, "vendorid=", &p)) {
	508	vendorid = strtol(p, &e, 16);
	509	if (e == p \|\| (e && e != ',' && *e != ':')) {
1ecda02b	510	error_report("bogus vendor ID %s", p);
a7954218 AZ	511	return NULL;
	512	}
	513	filename = e;
	514	} else if (strstart(filename, "productid=", &p)) {
	515	productid = strtol(p, &e, 16);
	516	if (e == p \|\| (e && e != ',' && *e != ':')) {
1ecda02b	517	error_report("bogus product ID %s", p);
a7954218 AZ	518	return NULL;
	519	}
	520	filename = e;
	521	} else {
1ecda02b	522	error_report("unrecognized serial USB option %s", filename);
a7954218 AZ	523	return NULL;
	524	}
	525	while(*filename == ',')
	526	filename++;
	527	}
	528	if (!*filename) {
1ecda02b	529	error_report("character device specification needed");
a7954218 AZ	530	return NULL;
	531	}
	532	filename++;
a7954218	533
5ccfae10	534	snprintf(label, sizeof(label), "usbserial%d", index++);
ceecf1d1	535	cdrv = qemu_chr_open(label, filename, NULL);
a7954218	536	if (!cdrv)
806b6024	537	return NULL;
a7954218	538
556cd098	539	dev = usb_create(NULL /* FIXME */, "usb-serial");
d44168ff PB	540	if (!dev) {
	541	return NULL;
	542	}
2b0efdc3 GH	543	qdev_prop_set_chr(&dev->qdev, "chardev", cdrv);
	544	if (vendorid)
	545	qdev_prop_set_uint16(&dev->qdev, "vendorid", vendorid);
	546	if (productid)
	547	qdev_prop_set_uint16(&dev->qdev, "productid", productid);
beb6f0de	548	qdev_init_nofail(&dev->qdev);
a7954218	549
2b0efdc3 GH	550	return dev;
	551	}
	552
	553	static USBDevice usb_braille_init(const char unused)
	554	{
	555	USBDevice *dev;
	556	CharDriverState *cdrv;
	557
	558	cdrv = qemu_chr_open("braille", "braille", NULL);
	559	if (!cdrv)
	560	return NULL;
806b6024	561
556cd098	562	dev = usb_create(NULL /* FIXME */, "usb-braille");
2b0efdc3	563	qdev_prop_set_chr(&dev->qdev, "chardev", cdrv);
beb6f0de	564	qdev_init_nofail(&dev->qdev);
2b0efdc3 GH	565
2b0efdc3 GH	566	return dev;
a7954218	567	}
806b6024 GH	568
806b6024 GH	569	static struct USBDeviceInfo serial_info = {
06384698	570	.product_desc = "QEMU USB Serial",
556cd098	571	.qdev.name = "usb-serial",
2b0efdc3	572	.qdev.size = sizeof(USBSerialState),
f29783f7	573	.usb_desc = &desc_serial,
2b0efdc3 GH	574	.init = usb_serial_initfn,
	575	.handle_packet = usb_generic_handle_packet,
	576	.handle_reset = usb_serial_handle_reset,
	577	.handle_control = usb_serial_handle_control,
	578	.handle_data = usb_serial_handle_data,
	579	.handle_destroy = usb_serial_handle_destroy,
	580	.usbdevice_name = "serial",
	581	.usbdevice_init = usb_serial_init,
	582	.qdev.props = (Property[]) {
f29783f7	583	DEFINE_PROP_CHR("chardev", USBSerialState, cs),
2b0efdc3 GH	584	DEFINE_PROP_END_OF_LIST(),
	585	},
	586	};
	587
	588	static struct USBDeviceInfo braille_info = {
06384698	589	.product_desc = "QEMU USB Braille",
556cd098	590	.qdev.name = "usb-braille",
806b6024	591	.qdev.size = sizeof(USBSerialState),
f29783f7	592	.usb_desc = &desc_braille,
806b6024 GH	593	.init = usb_serial_initfn,
	594	.handle_packet = usb_generic_handle_packet,
	595	.handle_reset = usb_serial_handle_reset,
	596	.handle_control = usb_serial_handle_control,
	597	.handle_data = usb_serial_handle_data,
	598	.handle_destroy = usb_serial_handle_destroy,
2b0efdc3 GH	599	.usbdevice_name = "braille",
	600	.usbdevice_init = usb_braille_init,
	601	.qdev.props = (Property[]) {
f29783f7	602	DEFINE_PROP_CHR("chardev", USBSerialState, cs),
2b0efdc3 GH	603	DEFINE_PROP_END_OF_LIST(),
2b0efdc3 GH	604	},
806b6024 GH	605	};
	606
	607	static void usb_serial_register_devices(void)
	608	{
	609	usb_qdev_register(&serial_info);
2b0efdc3	610	usb_qdev_register(&braille_info);
806b6024 GH	611	}
806b6024 GH	612	device_init(usb_serial_register_devices)