]> Git Repo - qemu.git/blame - hw/tusb6010.c
projects / qemu.git / blame
? search:
summary | shortlog | log | commit | commitdiff | tree
blob | blame (incremental) | history | HEAD
LSI SCSI qdev conversion
[qemu.git] / hw / tusb6010.c
CommitLineData
942ac052
AZ		 1/*
2 * Texas Instruments TUSB6010 emulation.
3 * Based on reverse-engineering of a linux driver.
4 *
5 * Copyright (C) 2008 Nokia Corporation
6 * Written by Andrzej Zaborowski <[email protected]>
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 or
11 * (at your option) version 3 of the License.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
fad6cb1a
AJ		 18 * You should have received a copy of the GNU General Public License along
19 * with this program; if not, write to the Free Software Foundation, Inc.,
20 * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
942ac052
AZ		 21 */
22#include "qemu-common.h"
23#include "qemu-timer.h"
24#include "usb.h"
25#include "omap.h"
26#include "irq.h"
b1d8e52e 27#include "devices.h"
942ac052 28
bc24a225 29struct TUSBState {
942ac052
AZ		 30 int iomemtype[2];
31 qemu_irq irq;
bc24a225 32 MUSBState *musb;
942ac052
AZ		 33 QEMUTimer *otg_timer;
34 QEMUTimer *pwr_timer;
35
36 int power;
37 uint32_t scratch;
38 uint16_t test_reset;
39 uint32_t prcm_config;
40 uint32_t prcm_mngmt;
41 uint16_t otg_status;
42 uint32_t dev_config;
43 int host_mode;
44 uint32_t intr;
45 uint32_t intr_ok;
46 uint32_t mask;
47 uint32_t usbip_intr;
48 uint32_t usbip_mask;
49 uint32_t gpio_intr;
50 uint32_t gpio_mask;
51 uint32_t gpio_config;
52 uint32_t dma_intr;
53 uint32_t dma_mask;
54 uint32_t dma_map;
55 uint32_t dma_config;
56 uint32_t ep0_config;
57 uint32_t rx_config[15];
58 uint32_t tx_config[15];
59 uint32_t wkup_mask;
60 uint32_t pullup[2];
61 uint32_t control_config;
62 uint32_t otg_timer_val;
63};
64
65#define TUSB_DEVCLOCK 60000000 /* 60 MHz */
66
67#define TUSB_VLYNQ_CTRL 0x004
68
69/* Mentor Graphics OTG core registers. */
70#define TUSB_BASE_OFFSET 0x400
71
72/* FIFO registers, 32-bit. */
73#define TUSB_FIFO_BASE 0x600
74
75/* Device System & Control registers, 32-bit. */
76#define TUSB_SYS_REG_BASE 0x800
77
78#define TUSB_DEV_CONF (TUSB_SYS_REG_BASE + 0x000)
79#define TUSB_DEV_CONF_USB_HOST_MODE (1 << 16)
80#define TUSB_DEV_CONF_PROD_TEST_MODE (1 << 15)
81#define TUSB_DEV_CONF_SOFT_ID (1 << 1)
82#define TUSB_DEV_CONF_ID_SEL (1 << 0)
83
84#define TUSB_PHY_OTG_CTRL_ENABLE (TUSB_SYS_REG_BASE + 0x004)
85#define TUSB_PHY_OTG_CTRL (TUSB_SYS_REG_BASE + 0x008)
86#define TUSB_PHY_OTG_CTRL_WRPROTECT (0xa5 << 24)
87#define TUSB_PHY_OTG_CTRL_O_ID_PULLUP (1 << 23)
88#define TUSB_PHY_OTG_CTRL_O_VBUS_DET_EN (1 << 19)
89#define TUSB_PHY_OTG_CTRL_O_SESS_END_EN (1 << 18)
90#define TUSB_PHY_OTG_CTRL_TESTM2 (1 << 17)
91#define TUSB_PHY_OTG_CTRL_TESTM1 (1 << 16)
92#define TUSB_PHY_OTG_CTRL_TESTM0 (1 << 15)
93#define TUSB_PHY_OTG_CTRL_TX_DATA2 (1 << 14)
94#define TUSB_PHY_OTG_CTRL_TX_GZ2 (1 << 13)
95#define TUSB_PHY_OTG_CTRL_TX_ENABLE2 (1 << 12)
96#define TUSB_PHY_OTG_CTRL_DM_PULLDOWN (1 << 11)
97#define TUSB_PHY_OTG_CTRL_DP_PULLDOWN (1 << 10)
98#define TUSB_PHY_OTG_CTRL_OSC_EN (1 << 9)
99#define TUSB_PHY_OTG_CTRL_PHYREF_CLK(v) (((v) & 3) << 7)
100#define TUSB_PHY_OTG_CTRL_PD (1 << 6)
101#define TUSB_PHY_OTG_CTRL_PLL_ON (1 << 5)
102#define TUSB_PHY_OTG_CTRL_EXT_RPU (1 << 4)
103#define TUSB_PHY_OTG_CTRL_PWR_GOOD (1 << 3)
104#define TUSB_PHY_OTG_CTRL_RESET (1 << 2)
105#define TUSB_PHY_OTG_CTRL_SUSPENDM (1 << 1)
106#define TUSB_PHY_OTG_CTRL_CLK_MODE (1 << 0)
107
108/* OTG status register */
109#define TUSB_DEV_OTG_STAT (TUSB_SYS_REG_BASE + 0x00c)
110#define TUSB_DEV_OTG_STAT_PWR_CLK_GOOD (1 << 8)
111#define TUSB_DEV_OTG_STAT_SESS_END (1 << 7)
112#define TUSB_DEV_OTG_STAT_SESS_VALID (1 << 6)
113#define TUSB_DEV_OTG_STAT_VBUS_VALID (1 << 5)
114#define TUSB_DEV_OTG_STAT_VBUS_SENSE (1 << 4)
115#define TUSB_DEV_OTG_STAT_ID_STATUS (1 << 3)
116#define TUSB_DEV_OTG_STAT_HOST_DISCON (1 << 2)
117#define TUSB_DEV_OTG_STAT_LINE_STATE (3 << 0)
118#define TUSB_DEV_OTG_STAT_DP_ENABLE (1 << 1)
119#define TUSB_DEV_OTG_STAT_DM_ENABLE (1 << 0)
120
121#define TUSB_DEV_OTG_TIMER (TUSB_SYS_REG_BASE + 0x010)
122#define TUSB_DEV_OTG_TIMER_ENABLE (1 << 31)
123#define TUSB_DEV_OTG_TIMER_VAL(v) ((v) & 0x07ffffff)
124#define TUSB_PRCM_REV (TUSB_SYS_REG_BASE + 0x014)
125
126/* PRCM configuration register */
127#define TUSB_PRCM_CONF (TUSB_SYS_REG_BASE + 0x018)
128#define TUSB_PRCM_CONF_SFW_CPEN (1 << 24)
129#define TUSB_PRCM_CONF_SYS_CLKSEL(v) (((v) & 3) << 16)
130
131/* PRCM management register */
132#define TUSB_PRCM_MNGMT (TUSB_SYS_REG_BASE + 0x01c)
133#define TUSB_PRCM_MNGMT_SRP_FIX_TMR(v) (((v) & 0xf) << 25)
134#define TUSB_PRCM_MNGMT_SRP_FIX_EN (1 << 24)
135#define TUSB_PRCM_MNGMT_VBUS_VAL_TMR(v) (((v) & 0xf) << 20)
136#define TUSB_PRCM_MNGMT_VBUS_VAL_FLT_EN (1 << 19)
137#define TUSB_PRCM_MNGMT_DFT_CLK_DIS (1 << 18)
138#define TUSB_PRCM_MNGMT_VLYNQ_CLK_DIS (1 << 17)
139#define TUSB_PRCM_MNGMT_OTG_SESS_END_EN (1 << 10)
140#define TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN (1 << 9)
141#define TUSB_PRCM_MNGMT_OTG_ID_PULLUP (1 << 8)
142#define TUSB_PRCM_MNGMT_15_SW_EN (1 << 4)
143#define TUSB_PRCM_MNGMT_33_SW_EN (1 << 3)
144#define TUSB_PRCM_MNGMT_5V_CPEN (1 << 2)
145#define TUSB_PRCM_MNGMT_PM_IDLE (1 << 1)
146#define TUSB_PRCM_MNGMT_DEV_IDLE (1 << 0)
147
148/* Wake-up source clear and mask registers */
149#define TUSB_PRCM_WAKEUP_SOURCE (TUSB_SYS_REG_BASE + 0x020)
150#define TUSB_PRCM_WAKEUP_CLEAR (TUSB_SYS_REG_BASE + 0x028)
151#define TUSB_PRCM_WAKEUP_MASK (TUSB_SYS_REG_BASE + 0x02c)
152#define TUSB_PRCM_WAKEUP_RESERVED_BITS (0xffffe << 13)
153#define TUSB_PRCM_WGPIO_7 (1 << 12)
154#define TUSB_PRCM_WGPIO_6 (1 << 11)
155#define TUSB_PRCM_WGPIO_5 (1 << 10)
156#define TUSB_PRCM_WGPIO_4 (1 << 9)
157#define TUSB_PRCM_WGPIO_3 (1 << 8)
158#define TUSB_PRCM_WGPIO_2 (1 << 7)
159#define TUSB_PRCM_WGPIO_1 (1 << 6)
160#define TUSB_PRCM_WGPIO_0 (1 << 5)
161#define TUSB_PRCM_WHOSTDISCON (1 << 4) /* Host disconnect */
162#define TUSB_PRCM_WBUS (1 << 3) /* USB bus resume */
163#define TUSB_PRCM_WNORCS (1 << 2) /* NOR chip select */
164#define TUSB_PRCM_WVBUS (1 << 1) /* OTG PHY VBUS */
165#define TUSB_PRCM_WID (1 << 0) /* OTG PHY ID detect */
166
167#define TUSB_PULLUP_1_CTRL (TUSB_SYS_REG_BASE + 0x030)
168#define TUSB_PULLUP_2_CTRL (TUSB_SYS_REG_BASE + 0x034)
169#define TUSB_INT_CTRL_REV (TUSB_SYS_REG_BASE + 0x038)
170#define TUSB_INT_CTRL_CONF (TUSB_SYS_REG_BASE + 0x03c)
171#define TUSB_USBIP_INT_SRC (TUSB_SYS_REG_BASE + 0x040)
172#define TUSB_USBIP_INT_SET (TUSB_SYS_REG_BASE + 0x044)
173#define TUSB_USBIP_INT_CLEAR (TUSB_SYS_REG_BASE + 0x048)
174#define TUSB_USBIP_INT_MASK (TUSB_SYS_REG_BASE + 0x04c)
175#define TUSB_DMA_INT_SRC (TUSB_SYS_REG_BASE + 0x050)
176#define TUSB_DMA_INT_SET (TUSB_SYS_REG_BASE + 0x054)
177#define TUSB_DMA_INT_CLEAR (TUSB_SYS_REG_BASE + 0x058)
178#define TUSB_DMA_INT_MASK (TUSB_SYS_REG_BASE + 0x05c)
179#define TUSB_GPIO_INT_SRC (TUSB_SYS_REG_BASE + 0x060)
180#define TUSB_GPIO_INT_SET (TUSB_SYS_REG_BASE + 0x064)
181#define TUSB_GPIO_INT_CLEAR (TUSB_SYS_REG_BASE + 0x068)
182#define TUSB_GPIO_INT_MASK (TUSB_SYS_REG_BASE + 0x06c)
183
184/* NOR flash interrupt source registers */
185#define TUSB_INT_SRC (TUSB_SYS_REG_BASE + 0x070)
186#define TUSB_INT_SRC_SET (TUSB_SYS_REG_BASE + 0x074)
187#define TUSB_INT_SRC_CLEAR (TUSB_SYS_REG_BASE + 0x078)
188#define TUSB_INT_MASK (TUSB_SYS_REG_BASE + 0x07c)
189#define TUSB_INT_SRC_TXRX_DMA_DONE (1 << 24)
190#define TUSB_INT_SRC_USB_IP_CORE (1 << 17)
191#define TUSB_INT_SRC_OTG_TIMEOUT (1 << 16)
192#define TUSB_INT_SRC_VBUS_SENSE_CHNG (1 << 15)
193#define TUSB_INT_SRC_ID_STATUS_CHNG (1 << 14)
194#define TUSB_INT_SRC_DEV_WAKEUP (1 << 13)
195#define TUSB_INT_SRC_DEV_READY (1 << 12)
196#define TUSB_INT_SRC_USB_IP_TX (1 << 9)
197#define TUSB_INT_SRC_USB_IP_RX (1 << 8)
198#define TUSB_INT_SRC_USB_IP_VBUS_ERR (1 << 7)
199#define TUSB_INT_SRC_USB_IP_VBUS_REQ (1 << 6)
200#define TUSB_INT_SRC_USB_IP_DISCON (1 << 5)
201#define TUSB_INT_SRC_USB_IP_CONN (1 << 4)
202#define TUSB_INT_SRC_USB_IP_SOF (1 << 3)
203#define TUSB_INT_SRC_USB_IP_RST_BABBLE (1 << 2)
204#define TUSB_INT_SRC_USB_IP_RESUME (1 << 1)
205#define TUSB_INT_SRC_USB_IP_SUSPEND (1 << 0)
206
207#define TUSB_GPIO_REV (TUSB_SYS_REG_BASE + 0x080)
208#define TUSB_GPIO_CONF (TUSB_SYS_REG_BASE + 0x084)
209#define TUSB_DMA_CTRL_REV (TUSB_SYS_REG_BASE + 0x100)
210#define TUSB_DMA_REQ_CONF (TUSB_SYS_REG_BASE + 0x104)
211#define TUSB_EP0_CONF (TUSB_SYS_REG_BASE + 0x108)
212#define TUSB_EP_IN_SIZE (TUSB_SYS_REG_BASE + 0x10c)
213#define TUSB_DMA_EP_MAP (TUSB_SYS_REG_BASE + 0x148)
214#define TUSB_EP_OUT_SIZE (TUSB_SYS_REG_BASE + 0x14c)
215#define TUSB_EP_MAX_PACKET_SIZE_OFFSET (TUSB_SYS_REG_BASE + 0x188)
216#define TUSB_SCRATCH_PAD (TUSB_SYS_REG_BASE + 0x1c4)
217#define TUSB_WAIT_COUNT (TUSB_SYS_REG_BASE + 0x1c8)
218#define TUSB_PROD_TEST_RESET (TUSB_SYS_REG_BASE + 0x1d8)
219
220#define TUSB_DIDR1_LO (TUSB_SYS_REG_BASE + 0x1f8)
221#define TUSB_DIDR1_HI (TUSB_SYS_REG_BASE + 0x1fc)
222
223/* Device System & Control register bitfields */
224#define TUSB_INT_CTRL_CONF_INT_RLCYC(v) (((v) & 0x7) << 18)
225#define TUSB_INT_CTRL_CONF_INT_POLARITY (1 << 17)
226#define TUSB_INT_CTRL_CONF_INT_MODE (1 << 16)
227#define TUSB_GPIO_CONF_DMAREQ(v) (((v) & 0x3f) << 24)
228#define TUSB_DMA_REQ_CONF_BURST_SIZE(v) (((v) & 3) << 26)
229#define TUSB_DMA_REQ_CONF_DMA_RQ_EN(v) (((v) & 0x3f) << 20)
230#define TUSB_DMA_REQ_CONF_DMA_RQ_ASR(v) (((v) & 0xf) << 16)
231#define TUSB_EP0_CONFIG_SW_EN (1 << 8)
232#define TUSB_EP0_CONFIG_DIR_TX (1 << 7)
233#define TUSB_EP0_CONFIG_XFR_SIZE(v) ((v) & 0x7f)
234#define TUSB_EP_CONFIG_SW_EN (1 << 31)
235#define TUSB_EP_CONFIG_XFR_SIZE(v) ((v) & 0x7fffffff)
236#define TUSB_PROD_TEST_RESET_VAL 0xa596
237
bc24a225 238int tusb6010_sync_io(TUSBState *s)
942ac052
AZ		 239{
240 return s->iomemtype[0];
241}
242
bc24a225 243int tusb6010_async_io(TUSBState *s)
942ac052
AZ		 244{
245 return s->iomemtype[1];
246}
247
bc24a225 248static void tusb_intr_update(TUSBState *s)
942ac052
AZ		 249{
250 if (s->control_config & TUSB_INT_CTRL_CONF_INT_POLARITY)
251 qemu_set_irq(s->irq, s->intr & ~s->mask & s->intr_ok);
252 else
253 qemu_set_irq(s->irq, (!(s->intr & ~s->mask)) & s->intr_ok);
254}
255
bc24a225 256static void tusb_usbip_intr_update(TUSBState *s)
942ac052
AZ		 257{
258 /* TX interrupt in the MUSB */
259 if (s->usbip_intr & 0x0000ffff & ~s->usbip_mask)
260 s->intr |= TUSB_INT_SRC_USB_IP_TX;
261 else
262 s->intr &= ~TUSB_INT_SRC_USB_IP_TX;
263
264 /* RX interrupt in the MUSB */
265 if (s->usbip_intr & 0xffff0000 & ~s->usbip_mask)
266 s->intr |= TUSB_INT_SRC_USB_IP_RX;
267 else
268 s->intr &= ~TUSB_INT_SRC_USB_IP_RX;
269
270 /* XXX: What about TUSB_INT_SRC_USB_IP_CORE? */
271
272 tusb_intr_update(s);
273}
274
bc24a225 275static void tusb_dma_intr_update(TUSBState *s)
942ac052
AZ		 276{
277 if (s->dma_intr & ~s->dma_mask)
278 s->intr |= TUSB_INT_SRC_TXRX_DMA_DONE;
279 else
280 s->intr &= ~TUSB_INT_SRC_TXRX_DMA_DONE;
281
282 tusb_intr_update(s);
283}
284
bc24a225 285static void tusb_gpio_intr_update(TUSBState *s)
942ac052
AZ		 286{
287 /* TODO: How is this signalled? */
288}
289
290extern CPUReadMemoryFunc *musb_read[];
291extern CPUWriteMemoryFunc *musb_write[];
292
293static uint32_t tusb_async_readb(void *opaque, target_phys_addr_t addr)
294{
bc24a225 295 TUSBState *s = (TUSBState *) opaque;
942ac052
AZ		 296
297 switch (addr & 0xfff) {
298 case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
299 return musb_read[0](s->musb, addr & 0x1ff);
300
301 case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
302 return musb_read[0](s->musb, 0x20 + ((addr >> 3) & 0x3c));
303 }
304
305 printf("%s: unknown register at %03x\n",
306 __FUNCTION__, (int) (addr & 0xfff));
307 return 0;
308}
309
310static uint32_t tusb_async_readh(void *opaque, target_phys_addr_t addr)
311{
bc24a225 312 TUSBState *s = (TUSBState *) opaque;
942ac052
AZ		 313
314 switch (addr & 0xfff) {
315 case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
316 return musb_read[1](s->musb, addr & 0x1ff);
317
318 case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
319 return musb_read[1](s->musb, 0x20 + ((addr >> 3) & 0x3c));
320 }
321
322 printf("%s: unknown register at %03x\n",
323 __FUNCTION__, (int) (addr & 0xfff));
324 return 0;
325}
326
327static uint32_t tusb_async_readw(void *opaque, target_phys_addr_t addr)
328{
bc24a225 329 TUSBState *s = (TUSBState *) opaque;
942ac052
AZ		 330 int offset = addr & 0xfff;
331 int epnum;
332 uint32_t ret;
333
334 switch (offset) {
335 case TUSB_DEV_CONF:
336 return s->dev_config;
337
338 case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
339 return musb_read[2](s->musb, offset & 0x1ff);
340
341 case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
342 return musb_read[2](s->musb, 0x20 + ((addr >> 3) & 0x3c));
343
344 case TUSB_PHY_OTG_CTRL_ENABLE:
345 case TUSB_PHY_OTG_CTRL:
346 return 0x00; /* TODO */
347
348 case TUSB_DEV_OTG_STAT:
349 ret = s->otg_status;
350#if 0
351 if (!(s->prcm_mngmt & TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN))
352 ret &= ~TUSB_DEV_OTG_STAT_VBUS_VALID;
353#endif
354 return ret;
355 case TUSB_DEV_OTG_TIMER:
356 return s->otg_timer_val;
357
358 case TUSB_PRCM_REV:
359 return 0x20;
360 case TUSB_PRCM_CONF:
361 return s->prcm_config;
362 case TUSB_PRCM_MNGMT:
363 return s->prcm_mngmt;
364 case TUSB_PRCM_WAKEUP_SOURCE:
365 case TUSB_PRCM_WAKEUP_CLEAR: /* TODO: What does this one return? */
366 return 0x00000000;
367 case TUSB_PRCM_WAKEUP_MASK:
368 return s->wkup_mask;
369
370 case TUSB_PULLUP_1_CTRL:
371 return s->pullup[0];
372 case TUSB_PULLUP_2_CTRL:
373 return s->pullup[1];
374
375 case TUSB_INT_CTRL_REV:
376 return 0x20;
377 case TUSB_INT_CTRL_CONF:
378 return s->control_config;
379
380 case TUSB_USBIP_INT_SRC:
381 case TUSB_USBIP_INT_SET: /* TODO: What do these two return? */
382 case TUSB_USBIP_INT_CLEAR:
383 return s->usbip_intr;
384 case TUSB_USBIP_INT_MASK:
385 return s->usbip_mask;
386
387 case TUSB_DMA_INT_SRC:
388 case TUSB_DMA_INT_SET: /* TODO: What do these two return? */
389 case TUSB_DMA_INT_CLEAR:
390 return s->dma_intr;
391 case TUSB_DMA_INT_MASK:
392 return s->dma_mask;
393
394 case TUSB_GPIO_INT_SRC: /* TODO: What do these two return? */
395 case TUSB_GPIO_INT_SET:
396 case TUSB_GPIO_INT_CLEAR:
397 return s->gpio_intr;
398 case TUSB_GPIO_INT_MASK:
399 return s->gpio_mask;
400
401 case TUSB_INT_SRC:
402 case TUSB_INT_SRC_SET: /* TODO: What do these two return? */
403 case TUSB_INT_SRC_CLEAR:
404 return s->intr;
405 case TUSB_INT_MASK:
406 return s->mask;
407
408 case TUSB_GPIO_REV:
409 return 0x30;
410 case TUSB_GPIO_CONF:
411 return s->gpio_config;
412
413 case TUSB_DMA_CTRL_REV:
414 return 0x30;
415 case TUSB_DMA_REQ_CONF:
416 return s->dma_config;
417 case TUSB_EP0_CONF:
418 return s->ep0_config;
419 case TUSB_EP_IN_SIZE ... (TUSB_EP_IN_SIZE + 0x3b):
420 epnum = (offset - TUSB_EP_IN_SIZE) >> 2;
421 return s->tx_config[epnum];
422 case TUSB_DMA_EP_MAP:
423 return s->dma_map;
424 case TUSB_EP_OUT_SIZE ... (TUSB_EP_OUT_SIZE + 0x3b):
425 epnum = (offset - TUSB_EP_OUT_SIZE) >> 2;
426 return s->rx_config[epnum];
427 case TUSB_EP_MAX_PACKET_SIZE_OFFSET ...
428 (TUSB_EP_MAX_PACKET_SIZE_OFFSET + 0x3b):
429 epnum = (offset - TUSB_EP_MAX_PACKET_SIZE_OFFSET) >> 2;
430 return 0x00000000; /* TODO */
431 case TUSB_WAIT_COUNT:
432 return 0x00; /* TODO */
433
434 case TUSB_SCRATCH_PAD:
435 return s->scratch;
436
437 case TUSB_PROD_TEST_RESET:
438 return s->test_reset;
439
440 /* DIE IDs */
441 case TUSB_DIDR1_LO:
442 return 0xa9453c59;
443 case TUSB_DIDR1_HI:
444 return 0x54059adf;
445 }
446
447 printf("%s: unknown register at %03x\n", __FUNCTION__, offset);
448 return 0;
449}
450
451static void tusb_async_writeb(void *opaque, target_phys_addr_t addr,
452 uint32_t value)
453{
bc24a225 454 TUSBState *s = (TUSBState *) opaque;
942ac052
AZ		 455
456 switch (addr & 0xfff) {
457 case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
458 musb_write[0](s->musb, addr & 0x1ff, value);
459 break;
460
461 case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
462 musb_write[0](s->musb, 0x20 + ((addr >> 3) & 0x3c), value);
463 break;
464
465 default:
466 printf("%s: unknown register at %03x\n",
467 __FUNCTION__, (int) (addr & 0xfff));
468 return;
469 }
470}
471
472static void tusb_async_writeh(void *opaque, target_phys_addr_t addr,
473 uint32_t value)
474{
bc24a225 475 TUSBState *s = (TUSBState *) opaque;
942ac052
AZ		 476
477 switch (addr & 0xfff) {
478 case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
479 musb_write[1](s->musb, addr & 0x1ff, value);
480 break;
481
482 case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
483 musb_write[1](s->musb, 0x20 + ((addr >> 3) & 0x3c), value);
484 break;
485
486 default:
487 printf("%s: unknown register at %03x\n",
488 __FUNCTION__, (int) (addr & 0xfff));
489 return;
490 }
491}
492
493static void tusb_async_writew(void *opaque, target_phys_addr_t addr,
494 uint32_t value)
495{
bc24a225 496 TUSBState *s = (TUSBState *) opaque;
942ac052
AZ		 497 int offset = addr & 0xfff;
498 int epnum;
499
500 switch (offset) {
501 case TUSB_VLYNQ_CTRL:
502 break;
503
504 case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
505 musb_write[2](s->musb, offset & 0x1ff, value);
506 break;
507
508 case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
509 musb_write[2](s->musb, 0x20 + ((addr >> 3) & 0x3c), value);
510 break;
511
512 case TUSB_DEV_CONF:
513 s->dev_config = value;
514 s->host_mode = (value & TUSB_DEV_CONF_USB_HOST_MODE);
515 if (value & TUSB_DEV_CONF_PROD_TEST_MODE)
2ac71179 516 hw_error("%s: Product Test mode not allowed\n", __FUNCTION__);
942ac052
AZ		 517 break;
518
519 case TUSB_PHY_OTG_CTRL_ENABLE:
520 case TUSB_PHY_OTG_CTRL:
521 return; /* TODO */
522 case TUSB_DEV_OTG_TIMER:
523 s->otg_timer_val = value;
524 if (value & TUSB_DEV_OTG_TIMER_ENABLE)
525 qemu_mod_timer(s->otg_timer, qemu_get_clock(vm_clock) +
526 muldiv64(TUSB_DEV_OTG_TIMER_VAL(value),
527 ticks_per_sec, TUSB_DEVCLOCK));
528 else
529 qemu_del_timer(s->otg_timer);
530 break;
531
532 case TUSB_PRCM_CONF:
533 s->prcm_config = value;
534 break;
535 case TUSB_PRCM_MNGMT:
536 s->prcm_mngmt = value;
537 break;
538 case TUSB_PRCM_WAKEUP_CLEAR:
539 break;
540 case TUSB_PRCM_WAKEUP_MASK:
541 s->wkup_mask = value;
542 break;
543
544 case TUSB_PULLUP_1_CTRL:
545 s->pullup[0] = value;
546 break;
547 case TUSB_PULLUP_2_CTRL:
548 s->pullup[1] = value;
549 break;
550 case TUSB_INT_CTRL_CONF:
551 s->control_config = value;
552 tusb_intr_update(s);
553 break;
554
555 case TUSB_USBIP_INT_SET:
556 s->usbip_intr |= value;
557 tusb_usbip_intr_update(s);
558 break;
559 case TUSB_USBIP_INT_CLEAR:
560 s->usbip_intr &= ~value;
561 tusb_usbip_intr_update(s);
562 musb_core_intr_clear(s->musb, ~value);
563 break;
564 case TUSB_USBIP_INT_MASK:
565 s->usbip_mask = value;
566 tusb_usbip_intr_update(s);
567 break;
568
569 case TUSB_DMA_INT_SET:
570 s->dma_intr |= value;
571 tusb_dma_intr_update(s);
572 break;
573 case TUSB_DMA_INT_CLEAR:
574 s->dma_intr &= ~value;
575 tusb_dma_intr_update(s);
576 break;
577 case TUSB_DMA_INT_MASK:
578 s->dma_mask = value;
579 tusb_dma_intr_update(s);
580 break;
581
582 case TUSB_GPIO_INT_SET:
583 s->gpio_intr |= value;
584 tusb_gpio_intr_update(s);
585 break;
586 case TUSB_GPIO_INT_CLEAR:
587 s->gpio_intr &= ~value;
588 tusb_gpio_intr_update(s);
589 break;
590 case TUSB_GPIO_INT_MASK:
591 s->gpio_mask = value;
592 tusb_gpio_intr_update(s);
593 break;
594
595 case TUSB_INT_SRC_SET:
596 s->intr |= value;
597 tusb_intr_update(s);
598 break;
599 case TUSB_INT_SRC_CLEAR:
600 s->intr &= ~value;
601 tusb_intr_update(s);
602 break;
603 case TUSB_INT_MASK:
604 s->mask = value;
605 tusb_intr_update(s);
606 break;
607
608 case TUSB_GPIO_CONF:
609 s->gpio_config = value;
610 break;
611 case TUSB_DMA_REQ_CONF:
612 s->dma_config = value;
613 break;
614 case TUSB_EP0_CONF:
615 s->ep0_config = value & 0x1ff;
616 musb_set_size(s->musb, 0, TUSB_EP0_CONFIG_XFR_SIZE(value),
617 value & TUSB_EP0_CONFIG_DIR_TX);
618 break;
619 case TUSB_EP_IN_SIZE ... (TUSB_EP_IN_SIZE + 0x3b):
620 epnum = (offset - TUSB_EP_IN_SIZE) >> 2;
621 s->tx_config[epnum] = value;
622 musb_set_size(s->musb, epnum + 1, TUSB_EP_CONFIG_XFR_SIZE(value), 1);
623 break;
624 case TUSB_DMA_EP_MAP:
625 s->dma_map = value;
626 break;
627 case TUSB_EP_OUT_SIZE ... (TUSB_EP_OUT_SIZE + 0x3b):
628 epnum = (offset - TUSB_EP_OUT_SIZE) >> 2;
629 s->rx_config[epnum] = value;
630 musb_set_size(s->musb, epnum + 1, TUSB_EP_CONFIG_XFR_SIZE(value), 0);
631 break;
632 case TUSB_EP_MAX_PACKET_SIZE_OFFSET ...
633 (TUSB_EP_MAX_PACKET_SIZE_OFFSET + 0x3b):
634 epnum = (offset - TUSB_EP_MAX_PACKET_SIZE_OFFSET) >> 2;
635 return; /* TODO */
636 case TUSB_WAIT_COUNT:
637 return; /* TODO */
638
639 case TUSB_SCRATCH_PAD:
640 s->scratch = value;
641 break;
642
643 case TUSB_PROD_TEST_RESET:
644 s->test_reset = value;
645 break;
646
647 default:
648 printf("%s: unknown register at %03x\n", __FUNCTION__, offset);
649 return;
650 }
651}
652
653static CPUReadMemoryFunc *tusb_async_readfn[] = {
654 tusb_async_readb,
655 tusb_async_readh,
656 tusb_async_readw,
657};
658
659static CPUWriteMemoryFunc *tusb_async_writefn[] = {
660 tusb_async_writeb,
661 tusb_async_writeh,
662 tusb_async_writew,
663};
664
665static void tusb_otg_tick(void *opaque)
666{
bc24a225 667 TUSBState *s = (TUSBState *) opaque;
942ac052
AZ		 668
669 s->otg_timer_val = 0;
670 s->intr |= TUSB_INT_SRC_OTG_TIMEOUT;
671 tusb_intr_update(s);
672}
673
674static void tusb_power_tick(void *opaque)
675{
bc24a225 676 TUSBState *s = (TUSBState *) opaque;
942ac052
AZ		 677
678 if (s->power) {
679 s->intr_ok = ~0;
680 tusb_intr_update(s);
681 }
682}
683
684static void tusb_musb_core_intr(void *opaque, int source, int level)
685{
bc24a225 686 TUSBState *s = (TUSBState *) opaque;
942ac052
AZ		 687 uint16_t otg_status = s->otg_status;
688
689 switch (source) {
690 case musb_set_vbus:
691 if (level)
692 otg_status |= TUSB_DEV_OTG_STAT_VBUS_VALID;
693 else
694 otg_status &= ~TUSB_DEV_OTG_STAT_VBUS_VALID;
695
696 /* XXX: only if TUSB_PHY_OTG_CTRL_OTG_VBUS_DET_EN set? */
697 /* XXX: only if TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN set? */
698 if (s->otg_status != otg_status) {
699 s->otg_status = otg_status;
700 s->intr |= TUSB_INT_SRC_VBUS_SENSE_CHNG;
701 tusb_intr_update(s);
702 }
703 break;
704
705 case musb_set_session:
706 /* XXX: only if TUSB_PHY_OTG_CTRL_OTG_SESS_END_EN set? */
707 /* XXX: only if TUSB_PRCM_MNGMT_OTG_SESS_END_EN set? */
708 if (level) {
709 s->otg_status |= TUSB_DEV_OTG_STAT_SESS_VALID;
710 s->otg_status &= ~TUSB_DEV_OTG_STAT_SESS_END;
711 } else {
712 s->otg_status &= ~TUSB_DEV_OTG_STAT_SESS_VALID;
713 s->otg_status |= TUSB_DEV_OTG_STAT_SESS_END;
714 }
715
716 /* XXX: some IRQ or anything? */
717 break;
718
719 case musb_irq_tx:
720 case musb_irq_rx:
721 s->usbip_intr = musb_core_intr_get(s->musb);
722 /* Fall through. */
723 default:
724 if (level)
725 s->intr |= 1 << source;
726 else
727 s->intr &= ~(1 << source);
728 tusb_intr_update(s);
729 break;
730 }
731}
732
bc24a225 733TUSBState *tusb6010_init(qemu_irq intr)
942ac052 734{
bc24a225 735 TUSBState *s = qemu_mallocz(sizeof(*s));
942ac052
AZ		 736
737 s->test_reset = TUSB_PROD_TEST_RESET_VAL;
738 s->host_mode = 0;
739 s->dev_config = 0;
740 s->otg_status = 0; /* !TUSB_DEV_OTG_STAT_ID_STATUS means host mode */
741 s->power = 0;
742 s->mask = 0xffffffff;
743 s->intr = 0x00000000;
744 s->otg_timer_val = 0;
745 s->iomemtype[1] = cpu_register_io_memory(0, tusb_async_readfn,
746 tusb_async_writefn, s);
747 s->irq = intr;
748 s->otg_timer = qemu_new_timer(vm_clock, tusb_otg_tick, s);
749 s->pwr_timer = qemu_new_timer(vm_clock, tusb_power_tick, s);
750 s->musb = musb_init(qemu_allocate_irqs(tusb_musb_core_intr, s,
751 __musb_irq_max));
752
753 return s;
754}
755
bc24a225 756void tusb6010_power(TUSBState *s, int on)
942ac052
AZ		 757{
758 if (!on)
759 s->power = 0;
760 else if (!s->power && on) {
761 s->power = 1;
762
763 /* Pull the interrupt down after TUSB6010 comes up. */
764 s->intr_ok = 0;
765 tusb_intr_update(s);
766 qemu_mod_timer(s->pwr_timer,
767 qemu_get_clock(vm_clock) + ticks_per_sec / 2);
768 }
769}
Empty description
This page took 0.301462 seconds and 4 git commands to generate.