Git Repo - linux.git/log

Revert "net: phy: Uniform PHY driver access"

This reverts commit 3ac8eed62596387214869319379c1fcba264d8c6, which did
more than it said on the box, and not only it replaced to_phy_driver
with phydev->drv, but it also removed the "!drv" check, without actually
explaining why that is fine.

That patch in fact breaks suspend/resume on any system which has PHY
devices with no drivers bound.

The stack trace is:

Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
pc : mdio_bus_phy_suspend+0xd8/0xec
lr : dpm_run_callback+0x38/0x90
Call trace:
mdio_bus_phy_suspend+0xd8/0xec
dpm_run_callback+0x38/0x90
__device_suspend+0x108/0x3cc
dpm_suspend+0x140/0x210
dpm_suspend_start+0x7c/0xa0
suspend_devices_and_enter+0x13c/0x540
pm_suspend+0x2a4/0x330

Examples why that assumption is not fine:

- There is an MDIO bus with a PHY device that doesn't have a specific
  PHY driver loaded, because mdiobus_register() automatically creates a
  PHY device for it but there is no specific PHY driver in the system.
  Normally under those circumstances, the generic PHY driver will be
  bound lazily to it (at phy_attach_direct time). But some Ethernet
  drivers attach to their PHY at .ndo_open time. Until then it, the
  to-be-driven-by-genphy PHY device will not have a driver. The blamed
  patch amounts to saying "you need to open all net devices before the
  system can suspend, to avoid the NULL pointer dereference".

- There is any raw MDIO device which has 'plausible' values in the PHY
  ID registers 2 and 3, which is located on an MDIO bus whose driver
  does not set bus->phy_mask = ~0 (which prevents auto-scanning of PHY
  devices). An example could be a MAC's internal MDIO bus with PCS
  devices on it, for serial links such as SGMII. PHY devices will get
  created for those PCSes too, due to that MDIO bus auto-scanning, and
  although those PHY devices are not used, they do not bother anybody
  either. PCS devices are usually managed in Linux as raw MDIO devices.
  Nonetheless, they do not have a PHY driver, nor does anybody attempt
  to connect to them (because they are not a PHY), and therefore this
  patch breaks that.

The goal itself of the patch is questionable, so I am going for a
straight revert. to_phy_driver does not seem to have a need to be
replaced by phydev->drv, in fact that might even trigger code paths
which were not given too deep of a thought.

For instance:

phy_probe populates phydev->drv at the beginning, but does not clean it
up on any error (including EPROBE_DEFER). So if the phydev driver
requests probe deferral, phydev->drv will remain populated despite there
being no driver bound.

If a system suspend starts in between the initial probe deferral request
and the subsequent probe retry, we will be calling the phydev->drv->suspend
method, but _before_ any phydev->drv->probe call has succeeded.

That is to say, if the phydev->drv is allocating any driver-private data
structure in ->probe, it pretty much expects that data structure to be
available in ->suspend. But it may not. That is a pretty insane
environment to present to PHY drivers.

In the code structure before the blamed patch, mdio_bus_phy_may_suspend
would just say "no, don't suspend" to any PHY device which does not have
a driver pointer _in_the_device_structure_ (not the phydev->drv). That
would essentially ensure that ->suspend will never get called for a
device that has not yet successfully completed probe. This is the code
structure the patch is returning to, via the revert.

Fixes: 3ac8eed62596 ("net: phy: Uniform PHY driver access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914140515.2311548-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: destroy the phylink instance on any error in dsa_slave_phy_setup

DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.

The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).

However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.

There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.

Fixes: aab9c4067d23 ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

MAINTAINERS: Add Nirmal Patel as VMD maintainer

Change my email to my unaffiliated address and move me to reviewer status.

Link: https://lore.kernel.org/r/20210909200221.29981-1-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@linux.dev>
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Nirmal Patel <nirmal.patel@linux.intel.com>

PCI: Add AMD GPU multi-function power dependencies

Some AMD GPUs have built-in USB xHCI and USB Type-C UCSI controllers with
power dependencies between the GPU and the other functions as in
6d2e369f0d4c ("PCI: Add NVIDIA GPU multi-function power dependencies").

Add device link support for the AMD integrated USB xHCI and USB Type-C UCSI
controllers.

Without this, runtime power management, including GPU resume and temp and
fan sensors don't work correctly.

Reported-at: https://gitlab.freedesktop.org/drm/amd/-/issues/1704
Link: https://lore.kernel.org/r/20210903063311.3606226-1-evan.quan@amd.com
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org

PCI/ACPI: Don't reset a fwnode set by OF

Commit 375553a93201 ("PCI: Setup ACPI fwnode early and at the same time
with OF") added a call to pci_set_acpi_fwnode() in pci_setup_device(),
which unconditionally clears any fwnode previously set by
pci_set_of_node().

pci_set_acpi_fwnode() looks for ACPI_COMPANION(), which only returns the
existing fwnode if it was set by ACPI_COMPANION_SET(). If it was set by
OF instead, ACPI_COMPANION() returns NULL and pci_set_acpi_fwnode()
accidentally clears the fwnode. To fix this, look for any fwnode instead
of just ACPI companions.

Fixes a virtio-iommu boot regression in v5.15-rc1.

Fixes: 375553a93201 ("PCI: Setup ACPI fwnode early and at the same time with OF")
Link: https://lore.kernel.org/r/20210913172358.1775381-1-jean-philippe@linaro.org
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

PCI/VPD: Defer VPD sizing until first access

7bac54497c3e ("PCI/VPD: Determine VPD size in pci_vpd_init()") reads VPD at
enumeration-time to find the size.  But this is quite slow, and we don't
need the size until we actually need data from VPD.  Dave reported a boot
slowdown of more than two minutes [1].

Defer the VPD sizing until a driver or the user (via sysfs) requests
information from VPD.

If devices are quirked because VPD is known not to work, don't bother even
looking for the VPD capability.  The VPD will not be accessible at all.

[1] https://lore.kernel.org/r/20210913141818.GA27911@codemonkey.org.uk/
Link: https://lore.kernel.org/r/20210914215543.GA1437800@bjorn-Precision-5520
Fixes: 7bac54497c3e ("PCI/VPD: Determine VPD size in pci_vpd_init()")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

qnx4: avoid stringop-overread errors

The qnx4 directory entries are 64-byte blocks that have different
contents depending on the a status byte that is in the last byte of the
block.

In particular, a directory entry can be either a "link info" entry with
a 48-byte name and pointers to the real inode information, or an "inode
entry" with a smaller 16-byte name and the full inode information.

But the code was written to always just treat the directory name as if
it was part of that "inode entry", and just extend the name to the
longer case if the status byte said it was a link entry.

That work just fine and gives the right results, but now that gcc is
tracking data structure accesses much more, the code can trigger a
compiler error about using up to 48 bytes (the long name) in a structure
that only has that shorter name in it:

   fs/qnx4/dir.c: In function ‘qnx4_readdir’:
   fs/qnx4/dir.c:51:32: error: ‘strnlen’ specified bound 48 exceeds source size 16 [-Werror=stringop-overread]
      51 |                         size = strnlen(de->di_fname, size);
         |                                ^~~~~~~~~~~~~~~~~~~~~~~~~~~
   In file included from fs/qnx4/qnx4.h:3,
                    from fs/qnx4/dir.c:16:
   include/uapi/linux/qnx4_fs.h:45:25: note: source object declared here
      45 |         char            di_fname[QNX4_SHORT_NAME_MAX];
         |                         ^~~~~~~~

which is because the source code doesn't really make this whole "one of
two different types" explicit.

Fix this by introducing a very explicit union of the two types, and
basically explaining to the compiler what is really going on.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sparc: avoid stringop-overread errors

The sparc mdesc code does pointer games with 'struct mdesc_hdr', but
didn't describe to the compiler how that header is then followed by the
data that the header describes.

As a result, gcc is now unhappy since it does stricter pointer range
tracking, and doesn't understand about how these things work.  This
results in various errors like:

    arch/sparc/kernel/mdesc.c: In function ‘mdesc_node_by_name’:
    arch/sparc/kernel/mdesc.c:647:22: error: ‘strcmp’ reading 1 or more bytes from a region of size 0 [-Werror=stringop-overread]
      647 |                 if (!strcmp(names + ep[ret].name_offset, name))
          |                      ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

which are easily avoided by just describing 'struct mdesc_hdr' better,
and making the node_block() helper function look into that unsized
data[] that follows the header.

This makes the sparc64 build happy again at least for my cross-compiler
version (gcc version 11.2.1).

Link: https://lore.kernel.org/lkml/CAHk-=wi4NW3NC0xWykkw=6LnjQD6D_rtRtxY9g8gQAJXtQMi8A@mail.gmail.com/
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'absolute-pointer' (patches from Guenter)

Merge absolute_pointer macro series from Guenter Roeck:
"Kernel test builds currently fail for several architectures with error
  messages such as the following.

  drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
  arch/m68k/include/asm/string.h:72:25: error:
        '__builtin_memcpy' reading 6 bytes from a region of size 0
                [-Werror=stringop-overread]

  Such warnings may be reported by gcc 11.x for string and memory
  operations on fixed addresses if gcc's builtin functions are used for
  those operations.

  This series introduces absolute_pointer() to fix the problem.
  absolute_pointer() disassociates a pointer from its originating symbol
  type and context, and thus prevents gcc from making assumptions about
  pointers passed to memory operations"

* emailed patches from Guenter Roeck <linux@roeck-us.net>:
  alpha: Use absolute_pointer to define COMMAND_LINE
  alpha: Move setup.h out of uapi
  net: i825xx: Use absolute_pointer for memcpy from fixed memory location
  compiler.h: Introduce absolute_pointer macro

alpha: Use absolute_pointer to define COMMAND_LINE

alpha:allmodconfig fails to build with the following error
when using gcc 11.x.

arch/alpha/kernel/setup.c: In function 'setup_arch':
arch/alpha/kernel/setup.c:493:13: error:
'strcmp' reading 1 or more bytes from a region of size 0

Avoid the problem by declaring COMMAND_LINE as absolute_pointer().

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

alpha: Move setup.h out of uapi

Most of the contents of setup.h have no value for userspace
applications. The file was probably moved to uapi accidentally.

Keep the file in uapi to define the alpha-specific COMMAND_LINE_SIZE.
Move all other defines to arch/alpha/include/asm/setup.h.

Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

net: i825xx: Use absolute_pointer for memcpy from fixed memory location

gcc 11.x reports the following compiler warning/error.

drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]

Use absolute_pointer() to work around the problem.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

compiler.h: Introduce absolute_pointer macro

absolute_pointer() disassociates a pointer from its originating symbol
type and context. Use it to prevent compiler warnings/errors such as

drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]

Such warnings may be reported by gcc 11.x for string and memory
operations on fixed addresses.

Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blk-cgroup: fix UAF by grabbing blkcg lock before destroying blkg pd

KASAN reports a use-after-free report when doing fuzz test:

[693354.104835] ==================================================================
[693354.105094] BUG: KASAN: use-after-free in bfq_io_set_weight_legacy+0xd3/0x160
[693354.105336] Read of size 4 at addr ffff888be0a35664 by task sh/1453338

[693354.105607] CPU: 41 PID: 1453338 Comm: sh Kdump: loaded Not tainted 4.18.0-147
[693354.105610] Hardware name: Huawei 2288H V5/BC11SPSCB0, BIOS 0.81 07/02/2018
[693354.105612] Call Trace:
[693354.105621]  dump_stack+0xf1/0x19b
[693354.105626]  ? show_regs_print_info+0x5/0x5
[693354.105634]  ? printk+0x9c/0xc3
[693354.105638]  ? cpumask_weight+0x1f/0x1f
[693354.105648]  print_address_description+0x70/0x360
[693354.105654]  kasan_report+0x1b2/0x330
[693354.105659]  ? bfq_io_set_weight_legacy+0xd3/0x160
[693354.105665]  ? bfq_io_set_weight_legacy+0xd3/0x160
[693354.105670]  bfq_io_set_weight_legacy+0xd3/0x160
[693354.105675]  ? bfq_cpd_init+0x20/0x20
[693354.105683]  cgroup_file_write+0x3aa/0x510
[693354.105693]  ? ___slab_alloc+0x507/0x540
[693354.105698]  ? cgroup_file_poll+0x60/0x60
[693354.105702]  ? 0xffffffff89600000
[693354.105708]  ? usercopy_abort+0x90/0x90
[693354.105716]  ? mutex_lock+0xef/0x180
[693354.105726]  kernfs_fop_write+0x1ab/0x280
[693354.105732]  ? cgroup_file_poll+0x60/0x60
[693354.105738]  vfs_write+0xe7/0x230
[693354.105744]  ksys_write+0xb0/0x140
[693354.105749]  ? __ia32_sys_read+0x50/0x50
[693354.105760]  do_syscall_64+0x112/0x370
[693354.105766]  ? syscall_return_slowpath+0x260/0x260
[693354.105772]  ? do_page_fault+0x9b/0x270
[693354.105779]  ? prepare_exit_to_usermode+0xf9/0x1a0
[693354.105784]  ? enter_from_user_mode+0x30/0x30
[693354.105793]  entry_SYSCALL_64_after_hwframe+0x65/0xca

[693354.105875] Allocated by task 1453337:
[693354.106001]  kasan_kmalloc+0xa0/0xd0
[693354.106006]  kmem_cache_alloc_node_trace+0x108/0x220
[693354.106010]  bfq_pd_alloc+0x96/0x120
[693354.106015]  blkcg_activate_policy+0x1b7/0x2b0
[693354.106020]  bfq_create_group_hierarchy+0x1e/0x80
[693354.106026]  bfq_init_queue+0x678/0x8c0
[693354.106031]  blk_mq_init_sched+0x1f8/0x460
[693354.106037]  elevator_switch_mq+0xe1/0x240
[693354.106041]  elevator_switch+0x25/0x40
[693354.106045]  elv_iosched_store+0x1a1/0x230
[693354.106049]  queue_attr_store+0x78/0xb0
[693354.106053]  kernfs_fop_write+0x1ab/0x280
[693354.106056]  vfs_write+0xe7/0x230
[693354.106060]  ksys_write+0xb0/0x140
[693354.106064]  do_syscall_64+0x112/0x370
[693354.106069]  entry_SYSCALL_64_after_hwframe+0x65/0xca

[693354.106114] Freed by task 1453336:
[693354.106225]  __kasan_slab_free+0x130/0x180
[693354.106229]  kfree+0x90/0x1b0
[693354.106233]  blkcg_deactivate_policy+0x12c/0x220
[693354.106238]  bfq_exit_queue+0xf5/0x110
[693354.106241]  blk_mq_exit_sched+0x104/0x130
[693354.106245]  __elevator_exit+0x45/0x60
[693354.106249]  elevator_switch_mq+0xd6/0x240
[693354.106253]  elevator_switch+0x25/0x40
[693354.106257]  elv_iosched_store+0x1a1/0x230
[693354.106261]  queue_attr_store+0x78/0xb0
[693354.106264]  kernfs_fop_write+0x1ab/0x280
[693354.106268]  vfs_write+0xe7/0x230
[693354.106271]  ksys_write+0xb0/0x140
[693354.106275]  do_syscall_64+0x112/0x370
[693354.106280]  entry_SYSCALL_64_after_hwframe+0x65/0xca

[693354.106329] The buggy address belongs to the object at ffff888be0a35580
                 which belongs to the cache kmalloc-1k of size 1024
[693354.106736] The buggy address is located 228 bytes inside of
                 1024-byte region [ffff888be0a35580, ffff888be0a35980)
[693354.107114] The buggy address belongs to the page:
[693354.107273] page:ffffea002f828c00 count:1 mapcount:0 mapping:ffff888107c17080 index:0x0 compound_mapcount: 0
[693354.107606] flags: 0x17ffffc0008100(slab|head)
[693354.107760] raw: 0017ffffc0008100 ffffea002fcbc808 ffffea0030bd3a08 ffff888107c17080
[693354.108020] raw: 0000000000000000 00000000001c001c 00000001ffffffff 0000000000000000
[693354.108278] page dumped because: kasan: bad access detected

[693354.108511] Memory state around the buggy address:
[693354.108671]  ffff888be0a35500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[693354.116396]  ffff888be0a35580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[693354.124473] >ffff888be0a35600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[693354.132421]                                                        ^
[693354.140284]  ffff888be0a35680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[693354.147912]  ffff888be0a35700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[693354.155281] ==================================================================

blkgs are protected by both queue and blkcg locks and holding
either should stabilize them. However, the path of destroying
blkg policy data is only protected by queue lock in
blkcg_activate_policy()/blkcg_deactivate_policy(). Other tasks
can get the blkg policy data before the blkg policy data is
destroyed, and use it after destroyed, which will result in a
use-after-free.

CPU0                             CPU1
blkcg_deactivate_policy
  spin_lock_irq(&q->queue_lock)
                                 bfq_io_set_weight_legacy
                                   spin_lock_irq(&blkcg->lock)
                                   blkg_to_bfqg(blkg)
                                     pd_to_bfqg(blkg->pd[pol->plid])
                                     ^^^^^^blkg->pd[pol->plid] != NULL
                                           bfqg != NULL
  pol->pd_free_fn(blkg->pd[pol->plid])
    pd_to_bfqg(blkg->pd[pol->plid])
    bfqg_put(bfqg)
      kfree(bfqg)
  blkg->pd[pol->plid] = NULL
  spin_unlock_irq(q->queue_lock);
                                   bfq_group_set_weight(bfqg, val, 0)
                                     bfqg->entity.new_weight
                                     ^^^^^^trigger uaf here
                                   spin_unlock_irq(&blkcg->lock);

Fix by grabbing the matching blkcg lock before trying to
destroy blkg policy data.

Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Li Jinlin <lijinlin3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20210914042605.3260596-1-lijinlin3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blkcg: fix memory leak in blk_iolatency_init

BUG: memory leak
unreferenced object 0xffff888129acdb80 (size 96):
  comm "syz-executor.1", pid 12661, jiffies 4294962682 (age 15.220s)
  hex dump (first 32 bytes):
    20 47 c9 85 ff ff ff ff 20 d4 8e 29 81 88 ff ff   G...... ..)....
    01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff82264ec8>] kmalloc include/linux/slab.h:591 [inline]
    [<ffffffff82264ec8>] kzalloc include/linux/slab.h:721 [inline]
    [<ffffffff82264ec8>] blk_iolatency_init+0x28/0x190 block/blk-iolatency.c:724
    [<ffffffff8225b8c4>] blkcg_init_queue+0xb4/0x1c0 block/blk-cgroup.c:1185
    [<ffffffff822253da>] blk_alloc_queue+0x22a/0x2e0 block/blk-core.c:566
    [<ffffffff8223b175>] blk_mq_init_queue_data block/blk-mq.c:3100 [inline]
    [<ffffffff8223b175>] __blk_mq_alloc_disk+0x25/0xd0 block/blk-mq.c:3124
    [<ffffffff826a9303>] loop_add+0x1c3/0x360 drivers/block/loop.c:2344
    [<ffffffff826a966e>] loop_control_get_free drivers/block/loop.c:2501 [inline]
    [<ffffffff826a966e>] loop_control_ioctl+0x17e/0x2e0 drivers/block/loop.c:2516
    [<ffffffff81597eec>] vfs_ioctl fs/ioctl.c:51 [inline]
    [<ffffffff81597eec>] __do_sys_ioctl fs/ioctl.c:874 [inline]
    [<ffffffff81597eec>] __se_sys_ioctl fs/ioctl.c:860 [inline]
    [<ffffffff81597eec>] __x64_sys_ioctl+0xfc/0x140 fs/ioctl.c:860
    [<ffffffff843fa745>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
    [<ffffffff843fa745>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
    [<ffffffff84600068>] entry_SYSCALL_64_after_hwframe+0x44/0xae

Once blk_throtl_init() queue init failed, blkcg_iolatency_exit() will
not be invoked for cleanup. That leads a memory leak. Swap the
blk_throtl_init() and blk_iolatency_init() calls can solve this.

Reported-by: syzbot+01321b15cc98e6bf96d6@syzkaller.appspotmail.com
Fixes: 19688d7f9592 (block/blk-cgroup: Swap the blk_throtl_init() and blk_iolatency_init() calls)
Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20210915072426.4022924-1-yanfei.xu@windriver.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

tools/bootconfig: Define memblock_free_ptr() to fix build error

The lib/bootconfig.c file is shared with the 'bootconfig' tooling, and
as a result, the changes incommit 77e02cf57b6c ("memblock: introduce
saner 'memblock_free_ptr()' interface") need to also be reflected in the
tooling header file.

So define the new memblock_free_ptr() wrapper, and remove unused __pa()
and memblock_free().

Fixes: 77e02cf57b6c ("memblock: introduce saner 'memblock_free_ptr()' interface")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

locking/rwbase: Take care of ordering guarantee for fastpath reader

Readers of rwbase can lock and unlock without taking any inner lock, if
that happens, we need the ordering provided by atomic operations to
satisfy the ordering semantics of lock/unlock. Without that, considering
the follow case:

{ X = 0 initially }

CPU 0 CPU 1
===== =====
rt_write_lock();
X = 1
rt_write_unlock():
  atomic_add(READER_BIAS - WRITER_BIAS, ->readers);
  // ->readers is READER_BIAS.
rt_read_lock():
  if ((r = atomic_read(->readers)) < 0) // True
    atomic_try_cmpxchg(->readers, r, r + 1); // succeed.
  <acquire the read lock via fast path>

r1 = X; // r1 may be 0, because nothing prevent the reordering
        // of "X=1" and atomic_add() on CPU 1.

Therefore audit every usage of atomic operations that may happen in a
fast path, and add necessary barriers.

Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20210909110203.953991276@infradead.org

locking/rwbase: Extract __rwbase_write_trylock()

The code in rwbase_write_lock() is a little non-obvious vs the
read+set 'trylock', extract the sequence into a helper function to
clarify the code.

This also provides a single site to fix fast-path ordering.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/YUCq3L+u44NDieEJ@hirez.programming.kicks-ass.net

locking/rwbase: Properly match set_and_save_state() to restore_state()

Noticed while looking at the readers race.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lkml.kernel.org/r/20210909110203.828203010@infradead.org

events: Reuse value read using READ_ONCE instead of re-reading it

In perf_event_addr_filters_apply, the task associated with
the event (event->ctx->task) is read using READ_ONCE at the beginning
of the function, checked, and then re-read from event->ctx->task,
voiding all guarantees of the checks. Reuse the value that was read by
READ_ONCE to ensure the consistency of the task struct throughout the
function.

Fixes: 375637bc52495 ("perf/core: Introduce address range filtering")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210906015310.12802-1-baptiste.lepers@gmail.com

io_uring: move iopoll reissue into regular IO path

230d50d448acb ("io_uring: move reissue into regular IO path")
made non-IOPOLL I/O to not retry from ki_complete handler. Follow it
steps and do the same for IOPOLL. Same problems, same implementation,
same -EAGAIN assumptions.

Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/f80dfee2d5fa7678f0052a8ab3cfca9496a112ca.1631699928.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Revert "iov_iter: track truncated size"

This reverts commit 2112ff5ce0c1128fe7b4d19cfe7f2b8ce5b595fa.

We no longer need to track the truncation count, the one user that did
need it has been converted to using iov_iter_restore() instead.

Signed-off-by: Jens Axboe <axboe@kernel.dk>

io_uring: use iov_iter state save/restore helpers

Get rid of the need to do re-expand and revert on an iterator when we
encounter a short IO, or failure that warrants a retry. Use the new
state save/restore helpers instead.

We keep the iov_iter_state persistent across retries, if we need to
restart the read or write operation. If there's a pending retry, the
operation will always exit with the state correctly saved.

Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge tag 'nvme-5.15-2021-09-15' of git://git.infradead.org/nvme into block-5.15

Pull NVMe fixes from Christoph:

"nvme fixes for Linux 5.15

- fix ANA state updates when a namespace is not present (Anton Eidelman)
- nvmet: fix a width vs precision bug in nvmet_subsys_attr_serial_show
   (Dan Carpenter)
- avoid race in shutdown namespace removal (Daniel Wagner)
- fix io_work priority inversion in nvme-tcp (Keith Busch)
- destroy cm id before destroy qp to avoid use after free (Ruozhu Li)"

* tag 'nvme-5.15-2021-09-15' of git://git.infradead.org/nvme:
  nvme-tcp: fix io_work priority inversion
  nvme-rdma: destroy cm id before destroy qp to avoid use after free
  nvme-multipath: fix ANA state updates when a namespace is not present
  nvme: avoid race in shutdown namespace removal
  nvmet: fix a width vs precision bug in nvmet_subsys_attr_serial_show()

Revert "of: property: fw_devlink: Add support for "phy-handle" property"

This reverts commit cf4b94c8530d14017fbddae26aad064ddc42edd4.

Some PHYs pointed to by "phy-handle" will never bind to a driver until a
consumer attaches to it. And when the consumer attaches to it, they get
forcefully bound to a generic PHY driver. In such cases, parsing the
phy-handle property and creating a device link will prevent the consumer
from ever probing. We don't want that. So revert support for
"phy-handle" property until we come up with a better mechanism for
binding PHYs to generic drivers before a consumer tries to attach to it.

Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210915081933.485112-1-saravanak@google.com
Signed-off-by: Rob Herring <robh@kernel.org>

s390: remove WARN_DYNAMIC_STACK

s390 is the only architecture which allows to set the
-mwarn-dynamicstack compile option. This however will also always
generate a warning with system call stack randomization, which uses
alloca to generate some random sized stack frame.

On the other hand Linus just enabled "-Werror" by default with commit
3fe617ccafd6 ("Enable '-Werror' by default for all kernel builds"),
which means compiles will always fail by default.

So instead of playing once again whack-a-mole for something which is
s390 specific, simply remove this option.

Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

s390/ap: fix kernel doc comments

Get rid of warnings like:

drivers/s390/crypto/ap_bus.c:216: warning:
bad line:
drivers/s390/crypto/ap_bus.c:444:
warning: Function parameter or member 'floating' not described in 'ap_interrupt_handler'

Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

s390: update defconfigs

Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

s390/sclp: fix Secure-IPL facility detection

Prevent out-of-range access if the returned SCLP SCCB response is smaller
in size than the address of the Secure-IPL flag.

Fixes: c9896acc7851 ("s390/ipl: Provide has_secure sysfs attribute")
Cc: stable@vger.kernel.org # 5.2+
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

s390/pci_mmio: fully validate the VMA before calling follow_pte()

We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f2605e ("mm: mmap: zap pages
with read mmap_sem in munmap").

find_vma() does not check if the address is >= the VMA start address;
use vma_lookup() instead.

Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Fixes: dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap")
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

powerpc/xics: Set the IRQ chip data for the ICS native backend

The ICS native driver relies on the IRQ chip data to find the struct
'ics_native' describing the ICS controller but it was removed by commit
248af248a8f4 ("powerpc/xics: Rename the map handler in a check handler").
Revert this change to fix the Microwatt SoC platform.

Fixes: 248af248a8f4 ("powerpc/xics: Rename the map handler in a check handler")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Gustavo Romero <gustavo.romero@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210913134056.3761960-1-clg@kaod.org

swiotlb-xen: drop DEFAULT_NSLABS

It was introduced by 4035b43da6da ("xen-swiotlb: remove xen_set_nslabs")
and then not removed by 2d29960af0be ("swiotlb: dynamically allocate
io_tlb_default_mem").

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/15259326-209a-1d11-338c-5018dc38abe8@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

swiotlb-xen: arrange to have buffer info logged

I consider it unhelpful that address and size of the buffer aren't put
in the log file; it makes diagnosing issues needlessly harder. The
majority of callers of swiotlb_init() also passes 1 for the "verbose"
parameter.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/2e3c8e68-36b2-4ae9-b829-bf7f75d39d47@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

swiotlb-xen: drop leftover __ref

Commit a98f565462f0 ("xen-swiotlb: split xen_swiotlb_init") should not
only have added __init to the split off function, but also should have
dropped __ref from the one left.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/7cd163e1-fe13-270b-384c-2708e8273d34@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

swiotlb-xen: limit init retries

Due to the use of max(1024, ...) there's no point retrying (and issuing
bogus log messages) when the number of slabs is already no larger than
this minimum value.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/984fa426-2b7b-4b77-5ce8-766619575b7f@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

swiotlb-xen: suppress certain init retries

Only on the 2nd of the paths leading to xen_swiotlb_init()'s "error"
label it is useful to retry the allocation; the first one did already
iterate through all possible order values.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/56477481-87da-4962-9661-5e1b277efde0@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

swiotlb-xen: maintain slab count properly

Generic swiotlb code makes sure to keep the slab count a multiple of the
number of slabs per segment. Yet even without checking whether any such
assumption is made elsewhere, it is easy to see that xen_swiotlb_fixup()
might alter unrelated memory when calling xen_create_contiguous_region()
for the last segment, when that's not a full one - the function acts on
full order-N regions, not individual pages.

Align the slab count suitably when halving it for a retry. Add a build
time check and a runtime one. Replace the no longer useful local
variable "slabs" by an "order" one calculated just once, outside of the
loop. Re-use "order" for calculating "dma_bits", and change the type of
the latter as well as the one of "i" while touching this anyway.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/dc054cb0-bec4-4db0-fc06-c9fc957b6e66@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

swiotlb-xen: fix late init retry

The commit referenced below removed the assignment of "bytes" from
xen_swiotlb_init() without - like done for xen_swiotlb_init_early() -
adding an assignment on the retry path, thus leading to excessively
sized allocations upon retries.

Fixes: 2d29960af0be ("swiotlb: dynamically allocate io_tlb_default_mem")
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/778299d6-9cfd-1c13-026e-25ee5d14ecb3@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

swiotlb-xen: avoid double free

Of the two paths leading to the "error" label in xen_swiotlb_init() one
didn't allocate anything, while the other did already free what was
allocated.

Fixes: b82776005369 ("xen/swiotlb: Use the swiotlb_late_init_with_tbl to init Xen-SWIOTLB late when PV PCI is used")
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/ce9c2adb-8a52-6293-982a-0d6ece943ac6@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

xen/pvcalls: backend can be a module

It's not clear to me why only the frontend has been tristate. Switch the
backend to be, too.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/54a6070c-92bb-36a3-2fc0-de9ccca438c5@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

xen: fix usage of pmd_populate in mremap for pv guests

Commit 0881ace292b662 ("mm/mremap: use pmd/pud_poplulate to update page
table entries") introduced a regression when running as Xen PV guest.

Today pmd_populate() for Xen PV assumes that the PFN inserted is
referencing a not yet used page table. In case of move_normal_pmd()
this is not true, resulting in WARN splats like:

[34321.304270] ------------[ cut here ]------------
[34321.304277] WARNING: CPU: 0 PID: 23628 at arch/x86/xen/multicalls.c:102 xen_mc_flush+0x176/0x1a0
[34321.304288] Modules linked in:
[34321.304291] CPU: 0 PID: 23628 Comm: apt-get Not tainted 5.14.1-20210906-doflr-mac80211debug+ #1
[34321.304294] Hardware name: MSI MS-7640/890FXA-GD70 (MS-7640)  , BIOS V1.8B1 09/13/2010
[34321.304296] RIP: e030:xen_mc_flush+0x176/0x1a0
[34321.304300] Code: 89 45 18 48 c1 e9 3f 48 89 ce e9 20 ff ff ff e8 60 03 00 00 66 90 5b 5d 41 5c 41 5d c3 48 c7 45 18 ea ff ff ff be 01 00 00 00 <0f> 0b 8b 55 00 48 c7 c7 10 97 aa 82 31 db 49 c7 c5 38 97 aa 82 65
[34321.304303] RSP: e02b:ffffc90000a97c90 EFLAGS: 00010002
[34321.304305] RAX: ffff88807d416398 RBX: ffff88807d416350 RCX: ffff88807d416398
[34321.304306] RDX: 0000000000000001 RSI: 0000000000000001 RDI: deadbeefdeadf00d
[34321.304308] RBP: ffff88807d416300 R08: aaaaaaaaaaaaaaaa R09: ffff888006160cc0
[34321.304309] R10: deadbeefdeadf00d R11: ffffea000026a600 R12: 0000000000000000
[34321.304310] R13: ffff888012f6b000 R14: 0000000012f6b000 R15: 0000000000000001
[34321.304320] FS:  00007f5071177800(0000) GS:ffff88807d400000(0000) knlGS:0000000000000000
[34321.304322] CS:  10000e030 DS: 0000 ES: 0000 CR0: 0000000080050033
[34321.304323] CR2: 00007f506f542000 CR3: 00000000160cc000 CR4: 0000000000000660
[34321.304326] Call Trace:
[34321.304331]  xen_alloc_pte+0x294/0x320
[34321.304334]  move_pgt_entry+0x165/0x4b0
[34321.304339]  move_page_tables+0x6fa/0x8d0
[34321.304342]  move_vma.isra.44+0x138/0x500
[34321.304345]  __x64_sys_mremap+0x296/0x410
[34321.304348]  do_syscall_64+0x3a/0x80
[34321.304352]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[34321.304355] RIP: 0033:0x7f507196301a
[34321.304358] Code: 73 01 c3 48 8b 0d 76 0e 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 49 89 ca b8 19 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 46 0e 0c 00 f7 d8 64 89 01 48
[34321.304360] RSP: 002b:00007ffda1eecd38 EFLAGS: 00000246 ORIG_RAX: 0000000000000019
[34321.304362] RAX: ffffffffffffffda RBX: 000056205f950f30 RCX: 00007f507196301a
[34321.304363] RDX: 0000000001a00000 RSI: 0000000001900000 RDI: 00007f506dc56000
[34321.304364] RBP: 0000000001a00000 R08: 0000000000000010 R09: 0000000000000004
[34321.304365] R10: 0000000000000001 R11: 0000000000000246 R12: 00007f506dc56060
[34321.304367] R13: 00007f506dc56000 R14: 00007f506dc56060 R15: 000056205f950f30
[34321.304368] ---[ end trace a19885b78fe8f33e ]---
[34321.304370] 1 of 2 multicall(s) failed: cpu 0
[34321.304371]   call  2: op=12297829382473034410 arg=[aaaaaaaaaaaaaaaa] result=-22

Fix that by modifying xen_alloc_ptpage() to only pin the page table in
case it wasn't pinned already.

Fixes: 0881ace292b662 ("mm/mremap: use pmd/pud_poplulate to update page table entries")
Cc: <stable@vger.kernel.org>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20210908073640.11299-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

xen: reset legacy rtc flag for PV domU

A Xen PV guest doesn't have a legacy RTC device, so reset the legacy
RTC flag. Otherwise the following WARN splat will occur at boot:

[    1.333404] WARNING: CPU: 1 PID: 1 at /home/gross/linux/head/drivers/rtc/rtc-mc146818-lib.c:25 mc146818_get_time+0x1be/0x210
[    1.333404] Modules linked in:
[    1.333404] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G        W         5.14.0-rc7-default+ #282
[    1.333404] RIP: e030:mc146818_get_time+0x1be/0x210
[    1.333404] Code: c0 64 01 c5 83 fd 45 89 6b 14 7f 06 83 c5 64 89 6b 14 41 83 ec 01 b8 02 00 00 00 44 89 63 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 <0f> 0b 48 c7 c7 30 0e ef 82 4c 89 e6 e8 71 2a 24 00 48 c7 c0 ff ff
[    1.333404] RSP: e02b:ffffc90040093df8 EFLAGS: 00010002
[    1.333404] RAX: 00000000000000ff RBX: ffffc90040093e34 RCX: 0000000000000000
[    1.333404] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 000000000000000d
[    1.333404] RBP: ffffffff82ef0e30 R08: ffff888005013e60 R09: 0000000000000000
[    1.333404] R10: ffffffff82373e9b R11: 0000000000033080 R12: 0000000000000200
[    1.333404] R13: 0000000000000000 R14: 0000000000000002 R15: ffffffff82cdc6d4
[    1.333404] FS:  0000000000000000(0000) GS:ffff88807d440000(0000) knlGS:0000000000000000
[    1.333404] CS:  10000e030 DS: 0000 ES: 0000 CR0: 0000000080050033
[    1.333404] CR2: 0000000000000000 CR3: 000000000260a000 CR4: 0000000000050660
[    1.333404] Call Trace:
[    1.333404]  ? wakeup_sources_sysfs_init+0x30/0x30
[    1.333404]  ? rdinit_setup+0x2b/0x2b
[    1.333404]  early_resume_init+0x23/0xa4
[    1.333404]  ? cn_proc_init+0x36/0x36
[    1.333404]  do_one_initcall+0x3e/0x200
[    1.333404]  kernel_init_freeable+0x232/0x28e
[    1.333404]  ? rest_init+0xd0/0xd0
[    1.333404]  kernel_init+0x16/0x120
[    1.333404]  ret_from_fork+0x1f/0x30

Cc: <stable@vger.kernel.org>
Fixes: 8d152e7a5c7537 ("x86/rtc: Replace paravirt rtc check with platform legacy quirk")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210903084937.19392-3-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

ptp: dp83640: don't define PAGE0

Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.

In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
    8 | #define PAGE0                     0x0000
                 from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
  187 | #define PAGE0   ((struct zeropage *)__PAGE_OFFSET)

Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnx2x: Fix enabling network interfaces without VFs

This function is called to enable SR-IOV when available,
not enabling interfaces without VFs was a regression.

Fixes: 65161c35554f ("bnx2x: Fix missing error code in bnx2x_iov_init_one()")
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reported-by: YunQiang Su <wzssyqa@gmail.com>
Tested-by: YunQiang Su <wzssyqa@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Shai Malin <smalin@marvell.com>
Link: https://lore.kernel.org/r/20210912190523.27991-1-bunk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

nvme: remove the call to nvme_update_disk_info in nvme_ns_remove

There is no need to explicitly unregister the integrity profile when
deleting the gendisk.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20210914070657.87677-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: flush the integrity workqueue in blk_integrity_unregister

When the integrity profile is unregistered there can still be integrity
reads queued up which could see a NULL verify_fn as shown by the race
window below:

CPU0                                    CPU1
  process_one_work                      nvme_validate_ns
    bio_integrity_verify_fn                nvme_update_ns_info
                                     nvme_update_disk_info
                                       blk_integrity_unregister
                                               ---set queue->integrity as 0
bio_integrity_process
--access bi->profile->verify_fn(bi is a pointer of queue->integity)

Before calling blk_integrity_unregister in nvme_update_disk_info, we must
make sure that there is no work item in the kintegrityd_wq. Just call
blk_flush_integrity to flush the work queue so the bug can be resolved.

Signed-off-by: Lihong Kou <koulihong@huawei.com>
[hch: split up and shortened the changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20210914070657.87677-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: check if a profile is actually registered in blk_integrity_unregister

While clearing the profile itself is harmless, we really should not clear
the stable writes flag if it wasn't set due to a registered integrity
profile.

Reported-by: Lihong Kou <koulihong@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20210914070657.87677-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

drm/ttm: fix type mismatch error on sparc64

On sparc64, __fls() returns an "int", but the drm TTM code expected it
to be "unsigned long" as on x86. As a result, on sparc (and arc, and
m68k) you get build errors because 'min()' checks that the types match.

As suggested by Linus, it can use min_t instead of min to force the type
to be "unsigned int".

Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memblock: introduce saner 'memblock_free_ptr()' interface

The boot-time allocation interface for memblock is a mess, with
'memblock_alloc()' returning a virtual pointer, but then you are
supposed to free it with 'memblock_free()' that takes a _physical_
address.

Not only is that all kinds of strange and illogical, but it actually
causes bugs, when people then use it like a normal allocation function,
and it fails spectacularly on a NULL pointer:

   https://lore.kernel.org/all/20210912140820.GD25450@xsang-OptiPlex-9020/

or just random memory corruption if the debug checks don't catch it:

   https://lore.kernel.org/all/61ab2d0c-3313-aaab-514c-e15b7aa054a0@suse.cz/

I really don't want to apply patches that treat the symptoms, when the
fundamental cause is this horribly confusing interface.

I started out looking at just automating a sane replacement sequence,
but because of this mix or virtual and physical addresses, and because
people have used the "__pa()" macro that can take either a regular
kernel pointer, or just the raw "unsigned long" address, it's all quite
messy.

So this just introduces a new saner interface for freeing a virtual
address that was allocated using 'memblock_alloc()', and that was kept
as a regular kernel pointer.  And then it converts a couple of users
that are obvious and easy to test, including the 'xbc_nodes' case in
lib/bootconfig.c that caused problems.

Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: 40caa127f3c7 ("init: bootconfig: Remove all bootconfig data when the init memory is removed")
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drm/amdgpu: use IS_ERR for debugfs APIs

debugfs APIs returns encoded error so use
IS_ERR for checking return value.

v2: return PTR_ERR(ent)

References: https://gitlab.freedesktop.org/drm/amd/-/issues/1686
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-By: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

amd/display: downgrade validation failure log level

In amdgpu_dm_atomic_check, dc_validate_global_state is called. On
failure this logs a warning to the kernel journal. However warnings
shouldn't be used for atomic test-only commit failures: user-space
might be perfoming a lot of atomic test-only commits to find the
best hardware configuration.

Downgrade the log to a regular DRM atomic message. While at it, use
the new device-aware logging infrastructure.

This fixes error messages in the kernel when running gamescope [1].

[1]: https://github.com/Plagman/gamescope/issues/245

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix use after free during BO move

The memory backing old_mem is already freed at that point, move the
check a bit more up.

Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: bfa3357ef9ab ("drm/ttm: allocate resource object instead of embedding it v2")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1699
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amd/pm: fix the issue of uploading powerplay table

fix the issue of uploading powerplay table due to the dependancy of rlc.

Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amd/amdgpu: Increase HWIP_MAX_INSTANCE to 10

Seems like newer cards can have even more instances now.
Found by UBSAN: array-index-out-of-bounds in
drivers/gpu/drm/amd/amdgpu/amdgpu_discovery.c:318:29
index 8 is out of range for type 'uint32_t *[8]'

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1697
Cc: stable@vger.kernel.org
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

ipc: remove memcg accounting for sops objects in do_semtimedop()

Linus proposes to revert an accounting for sops objects in
do_semtimedop() because it's really just a temporary buffer
for a single semtimedop() system call.

This object can consume up to 2 pages, syscall is sleeping
one, size and duration can be controlled by user, and this
allocation can be repeated by many thread at the same time.

However Shakeel Butt pointed that there are much more popular
objects with the same life time and similar memory
consumption, the accounting of which was decided to be
rejected for performance reasons.

Considering at least 2 pages for task_struct and 2 pages for
the kernel stack, a back of the envelope calculation gives a
footprint amplification of <1.5 so this temporal buffer can be
safely ignored.

The factor would IMO be interesting if it was >> 2 (from the
PoV of excessive (ab)use, fine-grained accounting seems to be
currently unfeasible due to performance impact).

Link: https://lore.kernel.org/lkml/90e254df-0dfe-f080-011e-b7c53ee7fd20@virtuozzo.com/
Fixes: 18319498fdd4 ("memcg: enable accounting of ipc resources")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

io_uring: allow retry for O_NONBLOCK if async is supported

A common complaint is that using O_NONBLOCK files with io_uring can be a
bit of a pain. Be a bit nicer and allow normal retry IFF the file does
support async behavior. This makes it possible to use io_uring more
reliably with O_NONBLOCK files, for use cases where it either isn't
possible or feasible to modify the file flags.

Cc: stable@vger.kernel.org
Reported-and-tested-by: Dan Melnic <dmm@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

cpufreq: schedutil: Destroy mutex before kobject_put() frees the memory

Since commit e5c6b312ce3c ("cpufreq: schedutil: Use kobject release()
method to free sugov_tunables") kobject_put() has kfree()d the
attr_set before gov_attr_set_put() returns.

kobject_put() isn't the last user of attr_set in gov_attr_set_put(),
the subsequent mutex_destroy() triggers a use-after-free:
| BUG: KASAN: use-after-free in mutex_is_locked+0x20/0x60
| Read of size 8 at addr ffff000800ca4250 by task cpuhp/2/20
|
| CPU: 2 PID: 20 Comm: cpuhp/2 Not tainted 5.15.0-rc1 #12369
| Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development
| Platform, BIOS EDK II Jul 30 2018
| Call trace:
|  dump_backtrace+0x0/0x380
|  show_stack+0x1c/0x30
|  dump_stack_lvl+0x8c/0xb8
|  print_address_description.constprop.0+0x74/0x2b8
|  kasan_report+0x1f4/0x210
|  kasan_check_range+0xfc/0x1a4
|  __kasan_check_read+0x38/0x60
|  mutex_is_locked+0x20/0x60
|  mutex_destroy+0x80/0x100
|  gov_attr_set_put+0xfc/0x150
|  sugov_exit+0x78/0x190
|  cpufreq_offline.isra.0+0x2c0/0x660
|  cpuhp_cpufreq_offline+0x14/0x24
|  cpuhp_invoke_callback+0x430/0x6d0
|  cpuhp_thread_fun+0x1b0/0x624
|  smpboot_thread_fn+0x5e0/0xa6c
|  kthread+0x3a0/0x450
|  ret_from_fork+0x10/0x20

Swap the order of the calls.

Fixes: e5c6b312ce3c ("cpufreq: schedutil: Use kobject release() method to free sugov_tunables")
Cc: 4.7+ <stable@vger.kernel.org> # 4.7+
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

drm/i915: Enable -Wsometimes-uninitialized

This warning helps catch uninitialized variables. It should have been
enabled at the same time as commit b2423184ac33 ("drm/i915: Enable
-Wuninitialized") but I did not realize they were disabled separately.
Enable it now that i915 is clean so that it stays that way.

Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210824225427.2065517-4-nathan@kernel.org
(cherry picked from commit 43192617f7816bb74584c1df06f57363afd15337)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/selftests: Always initialize err in igt_dmabuf_import_same_driver_lmem()

Clang warns:

drivers/gpu/drm/i915/gem/selftests/i915_gem_dmabuf.c:127:13: warning:
variable 'err' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
        } else if (PTR_ERR(import) != -EOPNOTSUPP) {
                   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/gem/selftests/i915_gem_dmabuf.c:138:9: note:
uninitialized use occurs here
        return err;
               ^~~
drivers/gpu/drm/i915/gem/selftests/i915_gem_dmabuf.c:127:9: note: remove
the 'if' if its condition is always true
        } else if (PTR_ERR(import) != -EOPNOTSUPP) {
               ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/gem/selftests/i915_gem_dmabuf.c:95:9: note:
initialize the variable 'err' to silence this warning
        int err;
               ^
                = 0

The test is expected to pass if i915_gem_prime_import() returns
-EOPNOTSUPP so initialize err to zero in this case.

Fixes: cdb35d1ed6d2 ("drm/i915/gem: Migrate to system at dma-buf attach time (v7)")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210824225427.2065517-3-nathan@kernel.org
(cherry picked from commit 46f20a353b80d02492655d99714f0566018a17e8)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/selftests: Do not use import_obj uninitialized

Clang warns a couple of times:

drivers/gpu/drm/i915/gem/selftests/i915_gem_dmabuf.c:63:6: warning:
variable 'import_obj' is used uninitialized whenever 'if' condition is
true [-Wsometimes-uninitialized]
        if (import != &obj->base) {
            ^~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/gem/selftests/i915_gem_dmabuf.c:80:22: note:
uninitialized use occurs here
        i915_gem_object_put(import_obj);
                            ^~~~~~~~~~
drivers/gpu/drm/i915/gem/selftests/i915_gem_dmabuf.c:63:2: note: remove
the 'if' if its condition is always false
        if (import != &obj->base) {
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/gem/selftests/i915_gem_dmabuf.c:38:46: note:
initialize the variable 'import_obj' to silence this warning
        struct drm_i915_gem_object *obj, *import_obj;
                                                    ^
                                                     = NULL

Shuffle the import_obj initialization above these if statements so that
it is not used uninitialized.

Fixes: d7b2cb380b3a ("drm/i915/gem: Correct the locking and pin pattern for dma-buf (v8)")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210824225427.2065517-2-nathan@kernel.org
(cherry picked from commit 4796054b381a586f4177a24e3d8b5a6a0a32ce62)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

io_uring: auto-removal for direct open/accept

It might be inconvenient that direct open/accept deviates from the
update semantics and fails if the slot is taken instead of removing a
file sitting there. Implement this auto-removal.

Note that removal might need to allocate and so may fail. However, if an
empty slot is specified, it's guaraneed to not fail on the fd
installation side for valid userspace programs. It's needed for users
who can't tolerate such failures, e.g. accept where the other end
never retries.

Suggested-by: Franz-B. Tuneke <franz-bernhard.tuneke@tu-dortmund.de>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/c896f14ea46b0eaa6c09d93149e665c2c37979b4.1631632300.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

powerpc/boot: Fix build failure since GCC 4.9 removal

Stephen reported that the build was broken since commit
6d2ef226f2f1 ("compiler_attributes.h: drop __has_attribute() support for
gcc4"), with errors such as:

  include/linux/compiler_attributes.h:296:5: warning: "__has_attribute" is not defined, evaluates to 0 [-Wundef]
    296 | #if __has_attribute(__warning__)
        |     ^~~~~~~~~~~~~~~
  make[2]: *** [arch/powerpc/boot/Makefile:225: arch/powerpc/boot/crt0.o] Error 1

But we expect __has_attribute() to always be defined now that we've
stopped using GCC 4.

Linus debugged it to the point of reading the GCC sources, and noticing
that the problem is that __has_attribute() is not defined when
preprocessing assembly files, which is what we're doing here.

Our assembly files don't include, or need, compiler_attributes.h, but
they are getting it unconditionally from the -include in BOOT_CFLAGS,
which is then added in its entirety to BOOT_AFLAGS.

That -include was added in commit 77433830ed16 ("powerpc: boot: include
compiler_attributes.h") so that we'd have "fallthrough" and other
attributes defined for the C files in arch/powerpc/boot. But it's not
needed for assembly files.

The minimal fix is to move the addition to BOOT_CFLAGS of -include
compiler_attributes.h until after we've copied BOOT_CFLAGS into
BOOT_AFLAGS. That avoids including compiler_attributes.h for asm files,
but makes no other change to BOOT_CFLAGS or BOOT_AFLAGS.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Debugged-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

io_uring: fix missing sigmask restore in io_cqring_wait()

Move get_timespec() section in io_cqring_wait() before the sigmask
saving, otherwise we'll fail to restore sigmask once get_timespec()
returns error.

Fixes: c73ebb685fb6 ("io_uring: add timeout support for io_uring_enter()")
Signed-off-by: Xiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20210914143852.9663-1-xiaoguang.wang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

iov_iter: add helper to save iov_iter state

In an ideal world, when someone is passed an iov_iter and returns X bytes,
then X bytes would have been consumed/advanced from the iov_iter. But we
have use cases that always consume the entire iterator, a few examples
of that are iomap and bdev O_DIRECT. This means we cannot rely on the
state of the iov_iter once we've called ->read_iter() or ->write_iter().

This would be easier if we didn't always have to deal with truncate of
the iov_iter, as rewinding would be trivial without that. We recently
added a commit to track the truncate state, but that grew the iov_iter
by 8 bytes and wasn't the best solution.

Implement a helper to save enough of the iov_iter state to sanely restore
it after we've called the read/write iterator helpers. This currently
only works for IOVEC/BVEC/KVEC as that's all we need, support for other
iterator types are left as an exercise for the reader.

Link: https://lore.kernel.org/linux-fsdevel/CAHk-=wiacKV4Gh-MYjteU0LwNBSGpWrK-Ov25HdqB1ewinrFPg@mail.gmail.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Revert "Revert "ipv4: fix memory leaks in ip_cmsg_send() callers""

This reverts commit d7807a9adf4856171f8441f13078c33941df48ab.

As mentioned in https://lkml.org/lkml/2021/9/13/1819
5 years old commit 919483096bfe ("ipv4: fix memory leaks in ip_cmsg_send() callers")
was a correct fix.

  ip_cmsg_send() can loop over multiple cmsghdr()

  If IP_RETOPTS has been successful, but following cmsghdr generates an error,
  we do not free ipc.ok

  If IP_RETOPTS is not successful, we have freed the allocated temporary space,
  not the one currently in ipc.opt.

Sure, code could be refactored, but let's not bring back old bugs.

Fixes: d7807a9adf48 ("Revert "ipv4: fix memory leaks in ip_cmsg_send() callers"")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: fix tp->undo_retrans accounting in tcp_sacktag_one()

Commit 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.

This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.

Before that commit (10d3be569243), the assumption underlying the
tp->undo_retrans-- seems correct.

Fixes: 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: zhenggy <zhenggy@chinatelecom.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sparc32: page align size in arch_dma_alloc

Commit 53b7670e5735 ("sparc: factor the dma coherent mapping into
helper") lost the page align for the calls to dma_make_coherent and
srmmu_unmapiorange. The latter cannot handle a non page aligned len
argument.

Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf

Daniel Borkmann says:

====================
pull-request: bpf 2021-09-14

The following pull-request contains BPF updates for your *net* tree.

We've added 7 non-merge commits during the last 13 day(s) which contain
a total of 18 files changed, 334 insertions(+), 193 deletions(-).

The main changes are:

1) Fix mmap_lock lockdep splat in BPF stack map's build_id lookup, from Yonghong Song.

2) Fix BPF cgroup v2 program bypass upon net_cls/prio activation, from Daniel Borkmann.

3) Fix kvcalloc() BTF line info splat on oversized allocation attempts, from Bixuan Cui.

4) Fix BPF selftest build of task_pt_regs test for arm64/s390, from Jean-Philippe Brucker.

5) Fix BPF's disasm.{c,h} to dual-license so that it is aligned with bpftool given the former
is a build dependency for the latter, from Daniel Borkmann with ACKs from contributors.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net-caif: avoid user-triggerable WARN_ON(1)

syszbot triggers this warning, which looks something
we can easily prevent.

If we initialize priv->list_field in chnl_net_init(),
then always use list_del_init(), we can remove robust_list_del()
completely.

WARNING: CPU: 0 PID: 3233 at net/caif/chnl_net.c:67 robust_list_del net/caif/chnl_net.c:67 [inline]
WARNING: CPU: 0 PID: 3233 at net/caif/chnl_net.c:67 chnl_net_uninit+0xc9/0x2e0 net/caif/chnl_net.c:375
Modules linked in:
CPU: 0 PID: 3233 Comm: syz-executor.3 Not tainted 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:robust_list_del net/caif/chnl_net.c:67 [inline]
RIP: 0010:chnl_net_uninit+0xc9/0x2e0 net/caif/chnl_net.c:375
Code: 89 eb e8 3a a3 ba f8 48 89 d8 48 c1 e8 03 42 80 3c 28 00 0f 85 bf 01 00 00 48 81 fb 00 14 4e 8d 48 8b 2b 75 d0 e8 17 a3 ba f8 <0f> 0b 5b 5d 41 5c 41 5d e9 0a a3 ba f8 4c 89 e3 e8 02 a3 ba f8 4c
RSP: 0018:ffffc90009067248 EFLAGS: 00010202
RAX: 0000000000008780 RBX: ffffffff8d4e1400 RCX: ffffc9000fd34000
RDX: 0000000000040000 RSI: ffffffff88bb6e49 RDI: 0000000000000003
RBP: ffff88802cd9ee08 R08: 0000000000000000 R09: ffffffff8d0e6647
R10: ffffffff88bb6dc2 R11: 0000000000000000 R12: ffff88803791ae08
R13: dffffc0000000000 R14: 00000000e600ffce R15: ffff888073ed3480
FS: 00007fed10fa0700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2c322000 CR3: 00000000164a6000 CR4: 00000000001506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
register_netdevice+0xadf/0x1500 net/core/dev.c:10347
ipcaif_newlink+0x4c/0x260 net/caif/chnl_net.c:468
__rtnl_newlink+0x106d/0x1750 net/core/rtnetlink.c:3458
rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3506
rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5572
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2504
netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1340
netlink_sendmsg+0x86d/0xdb0 net/netlink/af_netlink.c:1929
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:724
__sys_sendto+0x21c/0x320 net/socket.c:2036
__do_sys_sendto net/socket.c:2048 [inline]
__se_sys_sendto net/socket.c:2044 [inline]
__x64_sys_sendto+0xdd/0x1b0 net/socket.c:2044
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae

Fixes: cc36a070b590 ("net-caif: add CAIF netdevice")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nvme-tcp: fix io_work priority inversion

Dispatching requests inline with the .queue_rq() call may block while
holding the send_mutex. If the tcp io_work also happens to schedule, it
may see the req_list is non-empty, leaving "pending" true and remaining
in TASK_RUNNING. Since io_work is of higher scheduling priority, the
.queue_rq task may not get a chance to run, blocking forward progress
and leading to io timeouts.

Instead of checking for pending requests within io_work, let the queueing
restart io_work outside the send_mutex lock if there is more work to be
done.

Fixes: a0fdd1418007f ("nvme-tcp: rerun io_work if req_list is not empty")
Reported-by: Samuel Jones <sjones@kalrayinc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>

nvme-rdma: destroy cm id before destroy qp to avoid use after free

We should always destroy cm_id before destroy qp to avoid to get cma
event after qp was destroyed, which may lead to use after free.
In RDMA connection establishment error flow, don't destroy qp in cm
event handler.Just report cm_error to upper level, qp will be destroy
in nvme_rdma_alloc_queue() after destroy cm id.

Signed-off-by: Ruozhu Li <liruozhu@huawei.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

nvme-multipath: fix ANA state updates when a namespace is not present

nvme_update_ana_state() has a deficiency that results in a failure to
properly update the ana state for a namespace in the following case:

  NSIDs in ctrl->namespaces: 1, 3,    4
  NSIDs in desc->nsids: 1, 2, 3, 4

Loop iteration 0:
    ns index = 0, n = 0, ns->head->ns_id = 1, nsid = 1, MATCH.
Loop iteration 1:
    ns index = 1, n = 1, ns->head->ns_id = 3, nsid = 2, NO MATCH.
Loop iteration 2:
    ns index = 2, n = 2, ns->head->ns_id = 4, nsid = 4, MATCH.

Where the update to the ANA state of NSID 3 is missed.  To fix this
increment n and retry the update with the same ns when ns->head->ns_id is
higher than nsid,

Signed-off-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>

x86/mce: Avoid infinite loop for copy from user recovery

There are two cases for machine check recovery:

1) The machine check was triggered by ring3 (application) code.
   This is the simpler case. The machine check handler simply queues
   work to be executed on return to user. That code unmaps the page
   from all users and arranges to send a SIGBUS to the task that
   triggered the poison.

2) The machine check was triggered in kernel code that is covered by
   an exception table entry. In this case the machine check handler
   still queues a work entry to unmap the page, etc. but this will
   not be called right away because the #MC handler returns to the
   fix up code address in the exception table entry.

Problems occur if the kernel triggers another machine check before the
return to user processes the first queued work item.

Specifically, the work is queued using the ->mce_kill_me callback
structure in the task struct for the current thread. Attempting to queue
a second work item using this same callback results in a loop in the
linked list of work functions to call. So when the kernel does return to
user, it enters an infinite loop processing the same entry for ever.

There are some legitimate scenarios where the kernel may take a second
machine check before returning to the user.

1) Some code (e.g. futex) first tries a get_user() with page faults
   disabled. If this fails, the code retries with page faults enabled
   expecting that this will resolve the page fault.

2) Copy from user code retries a copy in byte-at-time mode to check
   whether any additional bytes can be copied.

On the other side of the fence are some bad drivers that do not check
the return value from individual get_user() calls and may access
multiple user addresses without noticing that some/all calls have
failed.

Fix by adding a counter (current->mce_count) to keep track of repeated
machine checks before task_work() is called. First machine check saves
the address information and calls task_work_add(). Subsequent machine
checks before that task_work call back is executed check that the address
is in the same page as the first machine check (since the callback will
offline exactly one page).

Expected worst case is four machine checks before moving on (e.g. one
user access with page faults disabled, then a repeat to the same address
with page faults enabled ... repeat in copy tail bytes). Just in case
there is some code that loops forever enforce a limit of 10.

[ bp: Massage commit message, drop noinstr, fix typo, extend panic
   messages. ]

Fixes: 5567d11c21a1 ("x86/mce: Send #MC singal from task work")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/YT/IJ9ziLqmtqEPu@agluck-desk2.amr.corp.intel.com

rtc: cmos: Disable irq around direct invocation of cmos_interrupt()

As previously noted in commit 66e4f4a9cc38 ("rtc: cmos: Use
spin_lock_irqsave() in cmos_interrupt()"):

<4>[  254.192378] WARNING: inconsistent lock state
<4>[  254.192384] 5.12.0-rc1-CI-CI_DRM_9834+ #1 Not tainted
<4>[  254.192396] --------------------------------
<4>[  254.192400] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
<4>[  254.192409] rtcwake/5309 [HC0[0]:SC0[0]:HE1:SE1] takes:
<4>[  254.192429] ffffffff8263c5f8 (rtc_lock){?...}-{2:2}, at: cmos_interrupt+0x18/0x100
<4>[  254.192481] {IN-HARDIRQ-W} state was registered at:
<4>[  254.192488]   lock_acquire+0xd1/0x3d0
<4>[  254.192504]   _raw_spin_lock+0x2a/0x40
<4>[  254.192519]   cmos_interrupt+0x18/0x100
<4>[  254.192536]   rtc_handler+0x1f/0xc0
<4>[  254.192553]   acpi_ev_fixed_event_detect+0x109/0x13c
<4>[  254.192574]   acpi_ev_sci_xrupt_handler+0xb/0x28
<4>[  254.192596]   acpi_irq+0x13/0x30
<4>[  254.192620]   __handle_irq_event_percpu+0x43/0x2c0
<4>[  254.192641]   handle_irq_event_percpu+0x2b/0x70
<4>[  254.192661]   handle_irq_event+0x2f/0x50
<4>[  254.192680]   handle_fasteoi_irq+0x9e/0x150
<4>[  254.192693]   __common_interrupt+0x76/0x140
<4>[  254.192715]   common_interrupt+0x96/0xc0
<4>[  254.192732]   asm_common_interrupt+0x1e/0x40
<4>[  254.192750]   _raw_spin_unlock_irqrestore+0x38/0x60
<4>[  254.192767]   resume_irqs+0xba/0xf0
<4>[  254.192786]   dpm_resume_noirq+0x245/0x3d0
<4>[  254.192811]   suspend_devices_and_enter+0x230/0xaa0
<4>[  254.192835]   pm_suspend.cold.8+0x301/0x34a
<4>[  254.192859]   state_store+0x7b/0xe0
<4>[  254.192879]   kernfs_fop_write_iter+0x11d/0x1c0
<4>[  254.192899]   new_sync_write+0x11d/0x1b0
<4>[  254.192916]   vfs_write+0x265/0x390
<4>[  254.192933]   ksys_write+0x5a/0xd0
<4>[  254.192949]   do_syscall_64+0x33/0x80
<4>[  254.192965]   entry_SYSCALL_64_after_hwframe+0x44/0xae
<4>[  254.192986] irq event stamp: 43775
<4>[  254.192994] hardirqs last  enabled at (43775): [<ffffffff81c00c42>] asm_sysvec_apic_timer_interrupt+0x12/0x20
<4>[  254.193023] hardirqs last disabled at (43774): [<ffffffff81aa691a>] sysvec_apic_timer_interrupt+0xa/0xb0
<4>[  254.193049] softirqs last  enabled at (42548): [<ffffffff81e00342>] __do_softirq+0x342/0x48e
<4>[  254.193074] softirqs last disabled at (42543): [<ffffffff810b45fd>] irq_exit_rcu+0xad/0xd0
<4>[  254.193101]
                  other info that might help us debug this:
<4>[  254.193107]  Possible unsafe locking scenario:

<4>[  254.193112]        CPU0
<4>[  254.193117]        ----
<4>[  254.193121]   lock(rtc_lock);
<4>[  254.193137]   <Interrupt>
<4>[  254.193142]     lock(rtc_lock);
<4>[  254.193156]
                   *** DEADLOCK ***

<4>[  254.193161] 6 locks held by rtcwake/5309:
<4>[  254.193174]  #0: ffff888104861430 (sb_writers#5){.+.+}-{0:0}, at: ksys_write+0x5a/0xd0
<4>[  254.193232]  #1: ffff88810f823288 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0xe7/0x1c0
<4>[  254.193282]  #2: ffff888100cef3c0 (kn->active#285
<7>[  254.192706] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<4>[  254.193307] ){.+.+}-{0:0}, at: kernfs_fop_write_iter+0xf0/0x1c0
<4>[  254.193333]  #3: ffffffff82649fa8 (system_transition_mutex){+.+.}-{3:3}, at: pm_suspend.cold.8+0xce/0x34a
<4>[  254.193387]  #4: ffffffff827a2108 (acpi_scan_lock){+.+.}-{3:3}, at: acpi_suspend_begin+0x47/0x70
<4>[  254.193433]  #5: ffff8881019ea178 (&dev->mutex){....}-{3:3}, at: device_resume+0x68/0x1e0
<4>[  254.193485]
                  stack backtrace:
<4>[  254.193492] CPU: 1 PID: 5309 Comm: rtcwake Not tainted 5.12.0-rc1-CI-CI_DRM_9834+ #1
<4>[  254.193514] Hardware name: Google Soraka/Soraka, BIOS MrChromebox-4.10 08/25/2019
<4>[  254.193524] Call Trace:
<4>[  254.193536]  dump_stack+0x7f/0xad
<4>[  254.193567]  mark_lock.part.47+0x8ca/0xce0
<4>[  254.193604]  __lock_acquire+0x39b/0x2590
<4>[  254.193626]  ? asm_sysvec_apic_timer_interrupt+0x12/0x20
<4>[  254.193660]  lock_acquire+0xd1/0x3d0
<4>[  254.193677]  ? cmos_interrupt+0x18/0x100
<4>[  254.193716]  _raw_spin_lock+0x2a/0x40
<4>[  254.193735]  ? cmos_interrupt+0x18/0x100
<4>[  254.193758]  cmos_interrupt+0x18/0x100
<4>[  254.193785]  cmos_resume+0x2ac/0x2d0
<4>[  254.193813]  ? acpi_pm_set_device_wakeup+0x1f/0x110
<4>[  254.193842]  ? pnp_bus_suspend+0x10/0x10
<4>[  254.193864]  pnp_bus_resume+0x5e/0x90
<4>[  254.193885]  dpm_run_callback+0x5f/0x240
<4>[  254.193914]  device_resume+0xb2/0x1e0
<4>[  254.193942]  ? pm_dev_err+0x25/0x25
<4>[  254.193974]  dpm_resume+0xea/0x3f0
<4>[  254.194005]  dpm_resume_end+0x8/0x10
<4>[  254.194030]  suspend_devices_and_enter+0x29b/0xaa0
<4>[  254.194066]  pm_suspend.cold.8+0x301/0x34a
<4>[  254.194094]  state_store+0x7b/0xe0
<4>[  254.194124]  kernfs_fop_write_iter+0x11d/0x1c0
<4>[  254.194151]  new_sync_write+0x11d/0x1b0
<4>[  254.194183]  vfs_write+0x265/0x390
<4>[  254.194207]  ksys_write+0x5a/0xd0
<4>[  254.194232]  do_syscall_64+0x33/0x80
<4>[  254.194251]  entry_SYSCALL_64_after_hwframe+0x44/0xae
<4>[  254.194274] RIP: 0033:0x7f07d79691e7
<4>[  254.194293] Code: 64 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
<4>[  254.194312] RSP: 002b:00007ffd9cc2c768 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
<4>[  254.194337] RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007f07d79691e7
<4>[  254.194352] RDX: 0000000000000004 RSI: 0000556ebfc63590 RDI: 000000000000000b
<4>[  254.194366] RBP: 0000556ebfc63590 R08: 0000000000000000 R09: 0000000000000004
<4>[  254.194379] R10: 0000556ebf0ec2a6 R11: 0000000000000246 R12: 0000000000000004

which breaks S3-resume on fi-kbl-soraka presumably as that's slow enough
to trigger the alarm during the suspend.

Fixes: 6950d046eb6e ("rtc: cmos: Replace spin_lock_irqsave with spin_lock in hard IRQ")
References: 66e4f4a9cc38 ("rtc: cmos: Use spin_lock_irqsave() in cmos_interrupt()"):
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Xiaofei Tan <tanxiaofei@huawei.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210305122140.28774-1-chris@chris-wilson.co.uk

drm/i915: Get PM ref before accessing HW register

Seeing these errors when GT is likely in suspend state-
"RPM wakelock ref not held during HW access"

Ensure GT is awake before trying to access HW registers. Avoid
reading the register if that is not the case.

Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Fixes: 41e5c17ebfc2 ("drm/i915/guc/slpc: Sysfs hooks for SLPC")
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210907232704.12982-1-vinay.belgaumkar@intel.com
(cherry picked from commit f25e3908b9cd4a3fe819e9bdcdde58f20bacb34c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Release ctx->syncobj on final put, not on ctx close

gem context refcounting is another exercise in least locking design it
seems, where most things get destroyed upon context closure (which can
race with anything really). Only the actual memory allocation and the
locks survive while holding a reference.

This tripped up Jason when reimplementing the single timeline feature
in

commit 00dae4d3d35d4f526929633b76e00b0ab4d3970d
Author: Jason Ekstrand <jason@jlekstrand.net>
Date: Thu Jul 8 10:48:12 2021 -0500

drm/i915: Implement SINGLE_TIMELINE with a syncobj (v4)

We could fix the bug by holding ctx->mutex in execbuf and clear the
pointer (again while holding the mutex) context_close, but it's
cleaner to just make the context object actually invariant over its
_entire_ lifetime. This way any other ioctl that's potentially racing,
but holding a full reference, can still rely on ctx->syncobj being
an immutable pointer. Which without this change, is not the case.

Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Fixes: 00dae4d3d35d ("drm/i915: Implement SINGLE_TIMELINE with a syncobj (v4)")
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: "Thomas Hellström" <thomas.hellstrom@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210902142057.929669-2-daniel.vetter@ffwll.ch
(cherry picked from commit c238980efd3b35af70fc926066cf7440f50a97a9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/gem: Fix the mman selftest

Using the I915_MMAP_TYPE_FIXED mmap type requires the TTM backend, so
for that mmap type, use __i915_gem_object_create_user() instead of
i915_gem_object_create_internal(), as we really want to tests objects
mmap-able by user-space.

This also means that the out-of-space error happens at object creation
and returns -ENXIO rather than -ENOSPC, so fix the code up to expect
that on out-of-offset-space errors.

Finally only use I915_MMAP_TYPE_FIXED for LMEM and SMEM for now if
testing on LMEM-capable devices. For stolen LMEM, we still take the
same path as for integrated, as that haven't been moved over to TTM yet,
and user-space should not be able to create out of stolen LMEM anyway.

v2:
- Check the presence of the obj->ops->mmap_offset callback rather than
hardcoding the supported mmap regions in can_mmap() (Maarten Lankhorst)

Fixes: 7961c5b60f23 ("drm/i915: Add TTM offset argument to mmap.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210831122931.157536-1-thomas.hellstrom@linux.intel.com
(cherry picked from commit 450cede7f3804ca7f8b3da210ebefa61c0958f22)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/guc: drop guc_communication_enabled

The function is only used from within GEM_BUG_ON(), which is causing
warnings with Wunneeded-internal-declaration in some builds. Since the
function is a simple wrapper around a CT function, we can just call the
CT function directly instead.

Fixes: 1fb12c587152 ("drm/i915/guc: skip disabling CTBs before sanitizing the GuC")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210823163137.19770-1-daniele.ceraolospurio@intel.com
(cherry picked from commit 5db1856781e45c9610f7652a19cc656b984235e7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/dp: Use max params for panels < eDP 1.4

Users reported that after commit 2bbd6dba84d4 ("drm/i915: Try to use
fast+narrow link on eDP again and fall back to the old max strategy on
failure"), the screen starts to have wobbly effect.

Commit a5c936add6a2 ("drm/i915/dp: Use slow and wide link training for
everything") doesn't help either, that means the affected eDP 1.2 panels
only work with max params.

So use max params for panels < eDP 1.4 as Windows does to solve the
issue.

v3:
- Do the eDP rev check in intel_edp_init_dpcd()

v2:
- Check eDP 1.4 instead of DPCD 1.1 to apply max params

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3714
Fixes: 2bbd6dba84d4 ("drm/i915: Try to use fast+narrow link on eDP again and fall back to the old max strategy on failure")
Fixes: a5c936add6a2 ("drm/i915/dp: Use slow and wide link training for everything")
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210820075301.693099-1-kai.heng.feng@canonical.com
(cherry picked from commit d7f213c131adf0bec8b731553eb82990cdac265d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/dp: return proper DPRX link training result

After DPRX link training, intel_dp_link_train_phy() did not
return the training result properly. If link training failed,
i915 driver would not run into link train fallback function.
And no hotplug uevent would be received by user space application.

Fixes: b30edfd8d0b4 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210706152541.25021-1-shawn.c.lee@intel.com
(cherry picked from commit dab1b47e57e053b2a02c22ead8e7449f79961335)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

PM: base: power: don't try to use non-existing RTC for storing data

If there is no legacy RTC device, don't try to use it for storing trace
data across suspend/resume.

Cc: <stable@vger.kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20210903084937.19392-2-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

xen/balloon: use a kernel thread instead a workqueue

Today the Xen ballooning is done via delayed work in a workqueue. This
might result in workqueue hangups being reported in case of large
amounts of memory are being ballooned in one go (here 16GB):

BUG: workqueue lockup - pool cpus=6 node=0 flags=0x0 nice=0 stuck for 64s!
Showing busy workqueues and worker pools:
workqueue events: flags=0x0
  pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=2/256 refcnt=3
    in-flight: 229:balloon_process
    pending: cache_reap
workqueue events_freezable_power_: flags=0x84
  pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=1/256 refcnt=2
    pending: disk_events_workfn
workqueue mm_percpu_wq: flags=0x8
  pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=1/256 refcnt=2
    pending: vmstat_update
pool 12: cpus=6 node=0 flags=0x0 nice=0 hung=64s workers=3 idle: 2222 43

This can easily be avoided by using a dedicated kernel thread for doing
the ballooning work.

Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210827123206.15429-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

io_uring: pin SQPOLL data before unlocking ring lock

We need to re-check sqd->thread after we've dropped the lock. Pin
the sqd before doing the lockdep lock dance, and check if the thread
is alive after that. It's either NULL or alive, as the SQPOLL thread
cannot exit without holding the same sqd->lock.

Reported-and-tested-by: syzbot+337de45f13a4fd54d708@syzkaller.appspotmail.com
Fixes: fa84693b3c89 ("io_uring: ensure IORING_REGISTER_IOWQ_MAX_WORKERS works with SQPOLL")
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bpf, selftests: Add test case for mixed cgroup v1/v2

Minimal selftest which implements a small BPF policy program to the
connect(2) hook which rejects TCP connection requests to port 60123
with EPERM. This is being attached to a non-root cgroup v2 path. The
test asserts that this works under cgroup v2-only and under a mixed
cgroup v1/v2 environment where net_classid is set in the former case.

Before fix:

  # ./test_progs -t cgroup_v1v2
  test_cgroup_v1v2:PASS:server_fd 0 nsec
  test_cgroup_v1v2:PASS:client_fd 0 nsec
  test_cgroup_v1v2:PASS:cgroup_fd 0 nsec
  test_cgroup_v1v2:PASS:server_fd 0 nsec
  run_test:PASS:skel_open 0 nsec
  run_test:PASS:prog_attach 0 nsec
  test_cgroup_v1v2:PASS:cgroup-v2-only 0 nsec
  run_test:PASS:skel_open 0 nsec
  run_test:PASS:prog_attach 0 nsec
  run_test:PASS:join_classid 0 nsec
  (network_helpers.c:219: errno: None) Unexpected success to connect to server
  test_cgroup_v1v2:FAIL:cgroup-v1v2 unexpected error: -1 (errno 0)
  #27 cgroup_v1v2:FAIL
  Summary: 0/0 PASSED, 0 SKIPPED, 1 FAILED

After fix:

  # ./test_progs -t cgroup_v1v2
  #27 cgroup_v1v2:OK
  Summary: 1/0 PASSED, 0 SKIPPED, 0 FAILED

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210913230759.2313-3-daniel@iogearbox.net

bpf, selftests: Add cgroup v1 net_cls classid helpers

Minimal set of helpers for net_cls classid cgroupv1 management in order
to set an id, join from a process, initiate setup and teardown. cgroupv2
helpers are left as-is, but reused where possible.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210913230759.2313-2-daniel@iogearbox.net

bpf, cgroups: Fix cgroup v2 fallback on v1/v2 mixed mode

Fix cgroup v1 interference when non-root cgroup v2 BPF programs are used.
Back in the days, commit bd1060a1d671 ("sock, cgroup: add sock->sk_cgroup")
embedded per-socket cgroup information into sock->sk_cgrp_data and in order
to save 8 bytes in struct sock made both mutually exclusive, that is, when
cgroup v1 socket tagging (e.g. net_cls/net_prio) is used, then cgroup v2
falls back to the root cgroup in sock_cgroup_ptr() (&cgrp_dfl_root.cgrp).

The assumption made was "there is no reason to mix the two and this is in line
with how legacy and v2 compatibility is handled" as stated in bd1060a1d671.
However, with Kubernetes more widely supporting cgroups v2 as well nowadays,
this assumption no longer holds, and the possibility of the v1/v2 mixed mode
with the v2 root fallback being hit becomes a real security issue.

Many of the cgroup v2 BPF programs are also used for policy enforcement, just
to pick _one_ example, that is, to programmatically deny socket related system
calls like connect(2) or bind(2). A v2 root fallback would implicitly cause
a policy bypass for the affected Pods.

In production environments, we have recently seen this case due to various
circumstances: i) a different 3rd party agent and/or ii) a container runtime
such as [0] in the user's environment configuring legacy cgroup v1 net_cls
tags, which triggered implicitly mentioned root fallback. Another case is
Kubernetes projects like kind [1] which create Kubernetes nodes in a container
and also add cgroup namespaces to the mix, meaning programs which are attached
to the cgroup v2 root of the cgroup namespace get attached to a non-root
cgroup v2 path from init namespace point of view. And the latter's root is
out of reach for agents on a kind Kubernetes node to configure. Meaning, any
entity on the node setting cgroup v1 net_cls tag will trigger the bypass
despite cgroup v2 BPF programs attached to the namespace root.

Generally, this mutual exclusiveness does not hold anymore in today's user
environments and makes cgroup v2 usage from BPF side fragile and unreliable.
This fix adds proper struct cgroup pointer for the cgroup v2 case to struct
sock_cgroup_data in order to address these issues; this implicitly also fixes
the tradeoffs being made back then with regards to races and refcount leaks
as stated in bd1060a1d671, and removes the fallback, so that cgroup v2 BPF
programs always operate as expected.

[0] https://github.com/nestybox/sysbox/
[1] https://kind.sigs.k8s.io/

Fixes: bd1060a1d671 ("sock, cgroup: add sock->sk_cgroup")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/bpf/20210913230759.2313-1-daniel@iogearbox.net

bpf: Add oversize check before call kvcalloc()

Commit 7661809d493b ("mm: don't allow oversized kvmalloc() calls") add the
oversize check. When the allocation is larger than what kmalloc() supports,
the following warning triggered:

WARNING: CPU: 0 PID: 8408 at mm/util.c:597 kvmalloc_node+0x108/0x110 mm/util.c:597
Modules linked in:
CPU: 0 PID: 8408 Comm: syz-executor221 Not tainted 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:kvmalloc_node+0x108/0x110 mm/util.c:597
Call Trace:
kvmalloc include/linux/mm.h:806 [inline]
kvmalloc_array include/linux/mm.h:824 [inline]
kvcalloc include/linux/mm.h:829 [inline]
check_btf_line kernel/bpf/verifier.c:9925 [inline]
check_btf_info kernel/bpf/verifier.c:10049 [inline]
bpf_check+0xd634/0x150d0 kernel/bpf/verifier.c:13759
bpf_prog_load kernel/bpf/syscall.c:2301 [inline]
__sys_bpf+0x11181/0x126e0 kernel/bpf/syscall.c:4587
__do_sys_bpf kernel/bpf/syscall.c:4691 [inline]
__se_sys_bpf kernel/bpf/syscall.c:4689 [inline]
__x64_sys_bpf+0x78/0x90 kernel/bpf/syscall.c:4689
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae

Reported-by: syzbot+f3e749d4c662818ae439@syzkaller.appspotmail.com
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210911005557.45518-1-cuibixuan@huawei.com

tools: compiler-gcc.h: Guard error attribute use with __has_attribute

When building objtool with HOSTCC=clang, there are several errors along
the lines of

orc_dump.c:201:28: error: unknown attribute 'error' ignored [-Werror,-Wunknown-attributes]

This occurs after commit 4e59869aa655 ("compiler-gcc.h: drop checks for
older GCC versions"), which removed the GCC_VERSION gating. The removed
version check just so happened to prevent __compiletime_error() from
being defined with clang because it pretends to be GCC 4.2.1 for
compatibility but the error attribute was not added to clang until
14.0.0.

Commit 815f0ddb346c ("include/linux/compiler*.h: make compiler-*.h
mutually exclusive") and commit a3f8a30f3f00 ("Compiler Attributes: use
feature checks instead of version checks") refactored the handling of
attributes in the main kernel to avoid situations like this but that
refactoring has never been done for the tools directory.

Refactoring is a rather large undertaking and this has never been an
issue before so instead, just guard the definition of
__compiletime_error() with __has_attribute() so that there are no more
errors.

Fixes: 4e59869aa655 ("compiler-gcc.h: drop checks for older GCC versions")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'gcc-min-version-5.1' (make gcc-5.1 the minimum version)

Merge patch series from Nick Desaulniers to update the minimum gcc
version to 5.1.

This is some of the left-overs from the merge window that I didn't want
to deal with yesterday, so it comes in after -rc1 but was sent before.

Gcc-4.9 support has been an annoyance for some time, and with -Werror I
had the choice of applying a fairly big patch from Kees Cook to remove a
fair number of initializer warnings (still leaving some), or this patch
series from Nick that just removes the source of the problem.

The initializer cleanups might still be worth it regardless, but
honestly, I preferred just tackling the problem with gcc-4.9 head-on.
We've been more aggressiuve about no longer having to care about
compilers that were released a long time ago, and I think it's been a
good thing.

I added a couple of patches on top to sort out a few left-overs now that
we no longer support gcc-4.x.

As noted by Arnd, as a result of this minimum compiler version upgrade
we can probably change our use of '--std=gnu89' to '--std=gnu11', and
finally start using local loop declarations etc.  But this series does
_not_ yet do that.

Link: https://lore.kernel.org/all/20210909182525.372ee687@canb.auug.org.au/
Link: https://lore.kernel.org/lkml/CAK7LNASs6dvU6D3jL2GG3jW58fXfaj6VNOe55NJnTB8UPuk2pA@mail.gmail.com/
Link: https://github.com/ClangBuiltLinux/linux/issues/1438
* emailed patches from Nick Desaulniers <ndesaulniers@google.com>:
  Drop some straggling mentions of gcc-4.9 as being stale
  compiler_attributes.h: drop __has_attribute() support for gcc4
  vmlinux.lds.h: remove old check for GCC 4.9
  compiler-gcc.h: drop checks for older GCC versions
  Makefile: drop GCC < 5 -fno-var-tracking-assignments workaround
  arm64: remove GCC version check for ARCH_SUPPORTS_INT128
  powerpc: remove GCC version check for UPD_CONSTR
  riscv: remove Kconfig check for GCC version for ARCH_RV64I
  Kconfig.debug: drop GCC 5+ version check for DWARF5
  mm/ksm: remove old GCC 4.9+ check
  compiler.h: drop fallback overflow checkers
  Documentation: raise minimum supported version of GCC to 5.1

Drop some straggling mentions of gcc-4.9 as being stale

Fix up the admin-guide README file to the new gcc-5.1 requirement, and
remove a stale comment about gcc support for the __assume_aligned__
attribute.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cpufreq: intel_pstate: Override parameters if HWP forced by BIOS

If HWP has been already been enabled by BIOS, it may be
necessary to override some kernel command line parameters.
Once it has been enabled it requires a reset to be disabled.

Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

compiler_attributes.h: drop __has_attribute() support for gcc4

Now that GCC 5.1 is the minimally supported default, the manual
workaround for older gcc versions not having __has_attribute() are no
longer relevant and can be removed.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vmlinux.lds.h: remove old check for GCC 4.9

Now that GCC 5.1 is the minimally supported version of GCC, we can
effectively revert commit 85c2ce9104eb ("sched, vmlinux.lds: Increase
STRUCT_ALIGNMENT to 64 bytes for GCC-4.9")

Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

compiler-gcc.h: drop checks for older GCC versions

Now that GCC 5.1 is the minimally supported default, drop the values we
don't use.

Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Makefile: drop GCC < 5 -fno-var-tracking-assignments workaround

Now that GCC 5.1 is the minimally supported version, we can drop this
workaround for older versions of GCC.

Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arm64: remove GCC version check for ARCH_SUPPORTS_INT128

Now that GCC 5.1 is the minimally supported compiler version, this
Kconfig check is no longer necessary.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

powerpc: remove GCC version check for UPD_CONSTR

Now that GCC 5.1 is the minimum supported version, we can drop this
workaround for older versions of GCC. This adversely affected clang,
too.

Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

riscv: remove Kconfig check for GCC version for ARCH_RV64I

The minimum supported version of GCC is now 5.1. The check wasn't
correct as written anyways since GCC_VERSION is 0 when CC=clang.

Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Kconfig.debug: drop GCC 5+ version check for DWARF5

Now that the minimum supported version of GCC is 5.1, we no longer need
this Kconfig version check for CONFIG_DEBUG_INFO_DWARF5.

Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/ksm: remove old GCC 4.9+ check

The minimum supported version of GCC has been raised to GCC 5.1.

Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>