Revert all changes done in hidinput_calc_abs_res as it mistakingly used
"Unit" item exponent nibbles to affect resolution value. This wasn't
breaking resolution calculation of relevant axes of any existing
devices, though, as they have only one dimension to their units and thus
1 in the corresponding nible.
Revert to reading "Unit Exponent" item value as a signed integer in
hid_parser_global to fix reading specification-complying values. This
fixes resolution calculation of devices complying to the HID standard,
including Huion, KYE, Waltop and UC-Logic graphics tablets which have
their report descriptors fixed by the drivers.
Explanations follow.
There are two "unit exponents" in HID specification and it is important
not to mix them. One is the global "Unit Exponent" item and another is
nibble values in the global "Unit" item. See 6.2.2.7 Global Items.
The "Unit Exponent" value is just a signed integer and is used to scale
the integer resolution unit values, so fractions can be expressed.
The nibbles of "Unit" value are used to select the unit system (nibble
0), and presence of a particular basic unit type in the unit formula and
its *exponent* (or power, nibbles 1-6). And yes, the latter is in two
complement and zero means absence of the unit type.
Taking the representation example of (integer) joules from the
specification:
the "Unit Exponent" would be -7 (or 0xF9, if stored as a byte) and the
"Unit" value would be 0xE121, signifying:
Nibble Part Value Meaning
----- ---- ----- -------
0 System 1 SI Linear
1 Length 2 Centimeters^2
2 Mass 1 Grams
3 Time -2 Seconds^-2
To give the resolution in e.g. hundredth of joules the "Unit Exponent"
item value should have been -9.
See also the examples of "Unit" values for some common units in the same
chapter.
However, there is a common misunderstanding about the "Unit Exponent"
value encoding, where it is assumed to be stored the same as nibbles in
"Unit" item. This is most likely due to the specification being a bit
vague and overloading the term "unit exponent". This also was and still
is proliferated by the official "HID Descriptor Tool", which makes this
mistake and stores "Unit Exponent" as such. This format is also
mentioned in books such as "USB Complete" and in Microsoft's hardware
design guides.
As a result many devices currently on the market use this encoding and
so the driver should support them.
* acpi-fixes:
ACPI / PM: Drop two functions that are not used any more
ATA / ACPI: remove power dependent device handling
ACPI / power: Drop automaitc resume of power resource dependent devices
ACPI: remove /proc/acpi/event from ACPI_BUTTON help
ACPI / power: Release resource_lock after acpi_power_get_state() return error
Chris Wilson [Wed, 16 Oct 2013 08:49:02 +0000 (09:49 +0100)]
drm: Pad drm_mode_get_connector to 64-bit boundary
Pavel Roskin reported that DRM_IOCTL_MODE_GETCONNECTOR was overwritting
the 4 bytes beyond the end of its structure with a 32-bit userspace
running on a 64-bit kernel. This is due to the padding gcc inserts as
the drm_mode_get_connector struct includes a u64 and its size is not a
natural multiple of u64s.
drm: block userspace under allocating buffer and having drivers overwrite it (v2)
to the core ioctl structs as well, for we found one instance where there
is a 32-/64-bit size mismatch and were guilty of writing beyond the end
of the user's buffer.
Linus Torvalds [Fri, 18 Oct 2013 01:49:21 +0000 (18:49 -0700)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Five small cifs fixes (includes fixes for: unmount hang, 2 security
related, symlink, large file writes)"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: ntstatus_to_dos_map[] is not terminated
cifs: Allow LANMAN auth method for servers supporting unencapsulated authentication methods
cifs: Fix inability to write files >2GB to SMB2/3 shares
cifs: Avoid umount hangs with smb2 when server is unresponsive
do not treat non-symlink reparse points as valid symlinks
It is possible to set bridge_forward_delay to be higher then
permitted maximum when STP is off. When turning STP on, the
higher then allowed delay has to be clamed down to max value.
Eric Dumazet [Tue, 15 Oct 2013 19:24:54 +0000 (12:24 -0700)]
tcp: remove the sk_can_gso() check from tcp_set_skb_tso_segs()
sk_can_gso() should only be used as a hint in tcp_sendmsg() to build GSO
packets in the first place. (As a performance hint)
Once we have GSO packets in write queue, we can not decide they are no
longer GSO only because flow now uses a route which doesn't handle
TSO/GSO.
Core networking stack handles the case very well for us, all we need
is keeping track of packet counts in MSS terms, regardless of
segmentation done later (in GSO or hardware)
Right now, if tcp_fragment() splits a GSO packet in two parts,
@left and @right, and route changed through a non GSO device,
both @left and @right have pcount set to 1, which is wrong,
and leads to incorrect packet_count tracking.
This problem was added in commit d5ac99a648 ("[TCP]: skb pcount with MTU
discovery")
Eric Dumazet [Tue, 15 Oct 2013 18:54:30 +0000 (11:54 -0700)]
tcp: must unclone packets before mangling them
TCP stack should make sure it owns skbs before mangling them.
We had various crashes using bnx2x, and it turned out gso_size
was cleared right before bnx2x driver was populating TC descriptor
of the _previous_ packet send. TCP stack can sometime retransmit
packets that are still in Qdisc.
Of course we could make bnx2x driver more robust (using
ACCESS_ONCE(shinfo->gso_size) for example), but the bug is TCP stack.
We have identified two points where skb_unclone() was needed.
This patch adds a WARN_ON_ONCE() to warn us if we missed another
fix of this kind.
Kudos to Neal for finding the root cause of this bug. Its visible
using small MSS.
Enrico Mioso [Tue, 15 Oct 2013 13:06:48 +0000 (15:06 +0200)]
net: qmi_wwan: Olivetti Olicard 200 support
This is a QMI device, manufactured by TCT Mobile Phones.
A companion patch blacklisting this device's QMI interface in the option.c
driver has been sent.
Jason Wang [Tue, 15 Oct 2013 03:18:59 +0000 (11:18 +0800)]
virtio-net: refill only when device is up during setting queues
We used to schedule the refill work unconditionally after changing the
number of queues. This may lead an issue if the device is not
up. Since we only try to cancel the work in ndo_stop(), this may cause
the refill work still work after removing the device. Fix this by only
schedule the work when device is up.
Dan Carpenter [Mon, 14 Oct 2013 12:28:38 +0000 (15:28 +0300)]
yam: integer underflow in yam_ioctl()
We cap bitrate at YAM_MAXBITRATE in yam_ioctl(), but it could also be
negative. I don't know the impact of using a negative bitrate but let's
prevent it.
Markus Pargmann [Sun, 13 Oct 2013 19:17:01 +0000 (21:17 +0200)]
net/ethernet: cpsw: Bugfix interrupts before enabling napi
If interrupts happen before napi_enable was called, the driver will not
work as expected. Network transmissions are impossible in this state.
This bug can be reproduced easily by restarting the network interface in
a loop. After some time any network transmissions on the network
interface will fail.
This patch fixes the bug by enabling napi before enabling the network
interface interrupts.
Eric Dumazet [Sat, 12 Oct 2013 21:08:34 +0000 (14:08 -0700)]
bnx2x: record rx queue for LRO packets
RPS support is kind of broken on bnx2x, because only non LRO packets
get proper rx queue information. This triggers reorders, as it seems
bnx2x like to generate a non LRO packet for segment including TCP PUSH
flag : (this might be pure coincidence, but all the reorders I've
seen involve segments with a PUSH)
11:13:34.335847 IP A > B: . 415808:447136(31328) ack 1 win 457 <nop,nop,timestamp 37893363985797>
11:13:34.335992 IP A > B: . 447136:448560(1424) ack 1 win 457 <nop,nop,timestamp 37893363985797>
11:13:34.336391 IP A > B: . 448560:479888(31328) ack 1 win 457 <nop,nop,timestamp 37893373985797>
11:13:34.336425 IP A > B: P 511216:512640(1424) ack 1 win 457 <nop,nop,timestamp 37893373985798>
11:13:34.336423 IP A > B: . 479888:511216(31328) ack 1 win 457 <nop,nop,timestamp 37893373985798>
11:13:34.336924 IP A > B: . 512640:543968(31328) ack 1 win 457 <nop,nop,timestamp 37893373985798>
11:13:34.336963 IP A > B: . 543968:575296(31328) ack 1 win 457 <nop,nop,timestamp 37893373985798>
We must call skb_record_rx_queue() to properly give to RPS (and more
generally for TX queue selection on forward path) the receive queue
information.
Similar fix is needed for skb_mark_napi_id(), but will be handled
in a separate patch to ease stable backports.
Yuchung Cheng [Sat, 12 Oct 2013 17:16:27 +0000 (10:16 -0700)]
tcp: fix incorrect ca_state in tail loss probe
On receiving an ACK that covers the loss probe sequence, TLP
immediately sets the congestion state to Open, even though some packets
are not recovered and retransmisssion are on the way. The later ACks
may trigger a WARN_ON check in step D of tcp_fastretrans_alert(), e.g.,
https://bugzilla.redhat.com/show_bug.cgi?id=989251
The fix is to follow the similar procedure in recovery by calling
tcp_try_keep_open(). The sender switches to Open state if no packets
are retransmissted. Otherwise it goes to Disorder and let subsequent
ACKs move the state to Recovery or Open.
David S. Miller [Thu, 17 Oct 2013 19:25:13 +0000 (15:25 -0400)]
Merge branch 'sctp_csum'
Vlad Yasevich says:
====================
sctp: Use software checksum under certain circumstances.
There are some cards that support SCTP checksum offloading. When using
these cards with IPSec or forcing IP fragmentation of SCTP traffic,
the checksum is computed incorrectly due to the fact that xfrm and IP/IPv6
fragmentation code do not know that this is SCTP traffic and do not
know that checksum has to be computed differently.
To fix this, we let SCTP detect these conditions and perform software
checksum calculation.
====================
Vlad Yasevich [Wed, 16 Oct 2013 02:01:31 +0000 (22:01 -0400)]
sctp: Perform software checksum if packet has to be fragmented.
IP/IPv6 fragmentation knows how to compute only TCP/UDP checksum.
This causes problems if SCTP packets has to be fragmented and
ipsummed has been set to PARTIAL due to checksum offload support.
This condition can happen when retransmitting after MTU discover,
or when INIT or other control chunks are larger then MTU.
Check for the rare fragmentation condition in SCTP and use software
checksum calculation in this case.
Fan Du [Wed, 16 Oct 2013 02:01:30 +0000 (22:01 -0400)]
sctp: Use software crc32 checksum when xfrm transform will happen.
igb/ixgbe have hardware sctp checksum support, when this feature is enabled
and also IPsec is armed to protect sctp traffic, ugly things happened as
xfrm_output checks CHECKSUM_PARTIAL to do checksum operation(sum every thing
up and pack the 16bits result in the checksum field). The result is fail
establishment of sctp communication.
Linus Torvalds [Thu, 17 Oct 2013 17:39:01 +0000 (10:39 -0700)]
Merge tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is one fix for the hotplug memory path that resolves a regression
when removing memory that showed up in 3.12-rc1"
* tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Release device_hotplug_lock when store_mem_state returns EINVAL
Linus Torvalds [Thu, 17 Oct 2013 17:38:18 +0000 (10:38 -0700)]
Merge tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 3.12-rc6
The largest change here is a bunch of new device ids for the option
USB serial driver for new Huawei devices. Other than that, just some
small bug fixes for issues that people have reported (run-time and
build-time), nothing major"
* tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
usb/chipidea: fix oops on memory allocation failure
usb-storage: add quirk for mandatory READ_CAPACITY_16
usb: serial: option: blacklist Olivetti Olicard200
USB: quirks: add touchscreen that is dazzeled by remote wakeup
Revert "usb: musb: gadget: fix otg active status flag"
USB: quirks.c: add one device that cannot deal with suspension
USB: serial: option: add support for Inovia SEW858 device
USB: serial: ti_usb_3410_5052: add Abbott strip port ID to combined table as well.
USB: support new huawei devices in option.c
usb: musb: start musb on the udc side, too
xhci: Fix spurious wakeups after S5 on Haswell
xhci: fix write to USB3_PSSEN and XUSB2PRM pci config registers
xhci: quirk for extra long delay for S4
xhci: Don't enable/disable RWE on bus suspend/resume.
Linus Torvalds [Thu, 17 Oct 2013 17:37:42 +0000 (10:37 -0700)]
Merge tag 'tty-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are two serial driver fixes for your tree. One is a revert of a
patch that causes a build error, the other is a fix to provide the
correct brace placement which resolves a bug where the driver was not
working properly"
* tag 'tty-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: vt8500: add missing braces
Revert "serial: i.MX: evaluate linux,stdout-path property"
Linus Torvalds [Thu, 17 Oct 2013 17:36:57 +0000 (10:36 -0700)]
Merge tag 'char-misc-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small iio and w1 driver fixes for 3.12-rc6.
There is also a hyper-v fix in here, which turned out to be incorrect,
so it was reverted. That will probably have to wait unto 3.13-rc1 to
get accepted as it's still being discussed"
* tag 'char-misc-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "Drivers: hv: vmbus: Fix a bug in channel rescind code"
Drivers: hv: vmbus: Fix a bug in channel rescind code
iio:buffer: Free active scan mask in iio_disable_all_buffers()
iio: frequency: adf4350: add missing clk_disable_unprepare() on error in adf4350_probe()
w1 - call request_module with w1 master mutex unlocked
w1 - fix fops in w1_bus_notify
David S. Miller [Thu, 17 Oct 2013 17:36:15 +0000 (13:36 -0400)]
Merge branch 'dm9000'
Nikita Kiryanov says:
====================
dm9000 improvements
This is a collection of improvements and bug fixes for dm9000, mostly
related to its startup and resume-from-suspend sequences.
Patch "Implement full reset of DM9000 network device" was submitted to the
linux-kernel mailing list but never applied.
An archive of the submission and the following conversation can be found here:
http://lkml.indiana.edu/hypermail/linux/kernel/1205.2/02817.html
====================
Michael Abbott [Wed, 16 Oct 2013 08:41:33 +0000 (11:41 +0300)]
dm9000: Implement full reset of DM9000 network device
A Davicom application note for the DM9000 network device recommends
performing software reset twice to correctly initialise the device.
Without this reset some devices fail to initialise correctly on
system startup.
Nikita Kiryanov [Wed, 16 Oct 2013 08:41:31 +0000 (11:41 +0300)]
dm9000: during init reset phy only for dm9000b
Some of the changes introduced in commit 6741f40 (DM9000B: driver
initialization upgrade) break functionality on DM9000A
(error message during NFS boot: "dm9000 dm9000.0: eth0: link down")
Since the changes were meant to serve only DM9000B, make them
dependent on the chip type.
Linus Torvalds [Thu, 17 Oct 2013 17:17:25 +0000 (10:17 -0700)]
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All reasonably small fixes as rc6: a HD-audio mic fix, a us122l mmap
regression fix, and kernel memory leak fix in hdsp driver. Hopefully
this will be the last pull request for 3.12..."
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hdsp - info leak in snd_hdsp_hwdep_ioctl()
ALSA: us122l: Fix pcm_usb_stream mmapping regression
ALSA: hda - Fix inverted internal mic not indicated on some machines
Linus Torvalds [Thu, 17 Oct 2013 17:16:45 +0000 (10:16 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull apparmor fixes from James Morris:
"A couple more regressions fixed"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
apparmor: fix bad lock balance when introspecting policy
apparmor: fix memleak of the profile hash
Merge tag 'iio-fixes-for-3.12c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
Third set of IIO fixes for the 3.12 cycle.
Two little ones this time:
1) A missing clk_unprepare in adf4350.
2) A missing free of the active_scan_mask when iio_disable_all_buffers is
called during an unexpected device removal. This leak was introduced by
the fix a87c82e454f184a9473f8cdfd4d304205f585f65 iio: Stop sampling when the device is removed
and hence is a regression fix.
Guenter Roeck [Thu, 17 Oct 2013 02:18:41 +0000 (19:18 -0700)]
usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
Commit 3fa4d734 (usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv)
changed the conditional around the declaration of usb_nop_xceiv_register
from
#if defined(CONFIG_NOP_USB_XCEIV) ||
(defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))
to
#if IS_ENABLED(CONFIG_NOP_USB_XCEIV)
While that looks the same, it is semantically different. The first expression
is true if CONFIG_NOP_USB_XCEIV is built as module and if the including
code is built as module. The second expression is true if code depending on
CONFIG_NOP_USB_XCEIV if built as module or into the kernel.
As a result, the arm:allmodconfig build fails with
arch/arm/mach-omap2/built-in.o: In function `omap3_evm_init':
arch/arm/mach-omap2/board-omap3evm.c:703: undefined reference to
`usb_nop_xceiv_register'
Fix the problem by reverting to the old conditional.
Revert "Drivers: hv: vmbus: Fix a bug in channel rescind code"
This reverts commit 90d33f3ec519db19d785216299a4ee85ef58ec97 as it's not
the correct fix for this issue, and it causes a build warning to be
added to the kernel tree.
ACPI / PM: Drop two functions that are not used any more
Two functions defined in device_pm.c, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), have no callers and may be
dropped, so drop them.
Moreover, they are the only functions adding entries to and removing
entries from the power_dependent list in struct acpi_device, so drop
that list too.
Aaron Lu [Thu, 17 Oct 2013 13:38:53 +0000 (15:38 +0200)]
ATA / ACPI: remove power dependent device handling
Previously, we wanted SCSI devices corrsponding to ATA devices to
be runtime resumed when the power resource for those ATA device was
turned on by some other device, so we added the SCSI device to the
dependent device list of the ATA device's ACPI node. However, this
code has no effect after commit 41863fc (ACPI / power: Drop automaitc
resume of power resource dependent devices) and the mechanism it was
supposed to implement is regarded as a bad idea now, so drop it.
Linus Torvalds [Thu, 17 Oct 2013 04:36:03 +0000 (21:36 -0700)]
Merge branch 'akpm' (fixes from Andrew Morton)
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <[email protected]>: (21 commits)
mm: revert mremap pud_free anti-fix
mm: fix BUG in __split_huge_page_pmd
swap: fix set_blocksize race during swapon/swapoff
procfs: call default get_unmapped_area on MMU-present architectures
procfs: fix unintended truncation of returned mapped address
writeback: fix negative bdi max pause
percpu_refcount: export symbols
fs: buffer: move allocation failure loop into the allocator
mm: memcg: handle non-error OOM situations more gracefully
tools/testing/selftests: fix uninitialized variable
block/partitions/efi.c: treat size mismatch as a warning, not an error
mm: hugetlb: initialize PG_reserved for tail pages of gigantic compound pages
mm/zswap: bugfix: memory leak when re-swapon
mm: /proc/pid/pagemap: inspect _PAGE_SOFT_DIRTY only on present pages
mm: migration: do not lose soft dirty bit if page is in migration state
gcov: MAINTAINERS: Add an entry for gcov
mm/hugetlb.c: correct missing private flag clearing
mm/vmscan.c: don't forget to free shrinker->nr_deferred
ipc/sem.c: synchronize semop and semctl with IPC_RMID
ipc: update locking scheme comments
...
Hugh Dickins [Wed, 16 Oct 2013 20:47:09 +0000 (13:47 -0700)]
mm: revert mremap pud_free anti-fix
Revert commit 1ecfd533f4c5 ("mm/mremap.c: call pud_free() after fail
calling pmd_alloc()").
The original code was correct: pud_alloc(), pmd_alloc(), pte_alloc_map()
ensure that the pud, pmd, pt is already allocated, and seldom do they
need to allocate; on failure, upper levels are freed if appropriate by
the subsequent do_munmap(). Whereas commit 1ecfd533f4c5 did an
unconditional pud_free() of a most-likely still-in-use pud: saved only
by the near-impossiblity of pmd_alloc() failing.
Hugh Dickins [Wed, 16 Oct 2013 20:47:08 +0000 (13:47 -0700)]
mm: fix BUG in __split_huge_page_pmd
Occasionally we hit the BUG_ON(pmd_trans_huge(*pmd)) at the end of
__split_huge_page_pmd(): seen when doing madvise(,,MADV_DONTNEED).
It's invalid: we don't always have down_write of mmap_sem there: a racing
do_huge_pmd_wp_page() might have copied-on-write to another huge page
before our split_huge_page() got the anon_vma lock.
Forget the BUG_ON, just go back and try again if this happens.
swap: fix set_blocksize race during swapon/swapoff
Fix race between swapoff and swapon. Swapoff used old_block_size from
swap_info outside of swapon_mutex so it could be overwritten by
concurrent swapon.
The race has visible effect only if more than one swap block device
exists with different block sizes (e.g. /dev/sda1 with block size 4096
and /dev/sdb1 with 512). In such case it leads to setting the blocksize
of swapped off device with wrong blocksize.
The bug can be triggered with multiple concurrent swapoff and swapon:
0. Swap for some device is on.
1. swapoff:
First the swapoff is called on this device and "struct swap_info_struct
*p" is assigned. This is done under swap_lock however this lock is
released for the call try_to_unuse().
2. swapon:
After the assignment above (and before acquiring swapon_mutex &
swap_lock by swapoff) the swapon is called on the same device.
The p->old_block_size is assigned to the value of block_size the device.
This block size should be the same as previous but sometimes it is not.
The swapon ends successfully.
3. swapoff:
Swapoff resumes, grabs the locks and mutex and continues to disable this
swap device. Now it sets the block size to value taken from swap_info
which was overwritten by swapon in 2.
HATAYAMA Daisuke [Wed, 16 Oct 2013 20:47:05 +0000 (13:47 -0700)]
procfs: call default get_unmapped_area on MMU-present architectures
Commit c4fe24485729 ("sparc: fix PCI device proc file mmap(2)") added
proc_reg_get_unmapped_area in proc_reg_file_ops and
proc_reg_file_ops_no_compat, by which now mmap always returns EIO if
get_unmapped_area method is not defined for the target procfs file,
which causes regression of mmap on /proc/vmcore.
To address this issue, like get_unmapped_area(), call default
current->mm->get_unmapped_area on MMU-present architectures if
pde->proc_fops->get_unmapped_area, i.e. the one in actual file
operation in the procfs file, is not defined.
HATAYAMA Daisuke [Wed, 16 Oct 2013 20:47:04 +0000 (13:47 -0700)]
procfs: fix unintended truncation of returned mapped address
Currently, proc_reg_get_unmapped_area truncates upper 32-bit of the
mapped virtual address returned from get_unmapped_area method in
pde->proc_fops due to the variable rv of signed integer on x86_64. This
is too small to have vitual address of unsigned long on x86_64 since on
x86_64, signed integer is of 4 bytes while unsigned long is of 8 bytes.
To fix this issue, use unsigned long instead.
Fixes a regression added in commit c4fe24485729 ("sparc: fix PCI device
proc file mmap(2)").
Since pause is bounded by [min_pause, max_pause] where min_pause is also
bounded by max_pause. It's suspected and demonstrated that the
max_pause calculation goes wrong:
The problem lies in the two "long = unsigned long" assignments in
bdi_max_pause() which might go negative if the highest bit is 1, and the
min_t(long, ...) check failed to protect it falling under 0. Fix all of
them by using "unsigned long" throughout the function.
Johannes Weiner [Wed, 16 Oct 2013 20:47:00 +0000 (13:47 -0700)]
fs: buffer: move allocation failure loop into the allocator
Buffer allocation has a very crude indefinite loop around waking the
flusher threads and performing global NOFS direct reclaim because it can
not handle allocation failures.
The most immediate problem with this is that the allocation may fail due
to a memory cgroup limit, where flushers + direct reclaim might not make
any progress towards resolving the situation at all. Because unlike the
global case, a memory cgroup may not have any cache at all, only
anonymous pages but no swap. This situation will lead to a reclaim
livelock with insane IO from waking the flushers and thrashing unrelated
filesystem cache in a tight loop.
Use __GFP_NOFAIL allocations for buffers for now. This makes sure that
any looping happens in the page allocator, which knows how to
orchestrate kswapd, direct reclaim, and the flushers sensibly. It also
allows memory cgroups to detect allocations that can't handle failure
and will allow them to ultimately bypass the limit if reclaim can not
make progress.
Johannes Weiner [Wed, 16 Oct 2013 20:46:59 +0000 (13:46 -0700)]
mm: memcg: handle non-error OOM situations more gracefully
Commit 3812c8c8f395 ("mm: memcg: do not trap chargers with full
callstack on OOM") assumed that only a few places that can trigger a
memcg OOM situation do not return VM_FAULT_OOM, like optional page cache
readahead. But there are many more and it's impractical to annotate
them all.
First of all, we don't want to invoke the OOM killer when the failed
allocation is gracefully handled, so defer the actual kill to the end of
the fault handling as well. This simplifies the code quite a bit for
added bonus.
Second, since a failed allocation might not be the abrupt end of the
fault, the memcg OOM handler needs to be re-entrant until the fault
finishes for subsequent allocation attempts. If an allocation is
attempted after the task already OOMed, allow it to bypass the limit so
that it can quickly finish the fault and invoke the OOM killer.
Doug Anderson [Wed, 16 Oct 2013 20:46:57 +0000 (13:46 -0700)]
block/partitions/efi.c: treat size mismatch as a warning, not an error
In commit 27a7c642174e ("partitions/efi: account for pmbr size in lba")
we started treating bad sizes in lba field of the partition that has the
0xEE (GPT protective) as errors.
However, we may run into these "bad sizes" in the real world if someone
uses dd to copy an image from a smaller disk to a bigger disk. Since
this case used to work (even without using force_gpt), keep it working
and treat the size mismatch as a warning instead of an error.
Andrea Arcangeli [Wed, 16 Oct 2013 20:46:56 +0000 (13:46 -0700)]
mm: hugetlb: initialize PG_reserved for tail pages of gigantic compound pages
Commit 11feeb498086 ("kvm: optimize away THP checks in
kvm_is_mmio_pfn()") introduced a memory leak when KVM is run on gigantic
compound pages.
That commit depends on the assumption that PG_reserved is identical for
all head and tail pages of a compound page. So that if get_user_pages
returns a tail page, we don't need to check the head page in order to
know if we deal with a reserved page that requires different
refcounting.
The assumption that PG_reserved is the same for head and tail pages is
certainly correct for THP and regular hugepages, but gigantic hugepages
allocated through bootmem don't clear the PG_reserved on the tail pages
(the clearing of PG_reserved is done later only if the gigantic hugepage
is freed).
This patch corrects the gigantic compound page initialization so that we
can retain the optimization in 11feeb498086. The cacheline was already
modified in order to set PG_tail so this won't affect the boot time of
large memory systems.
Consider the following scenario:
thread 0: reclaim entry x (get refcount, but not call zswap_get_swap_cache_page)
thread 1: call zswap_frontswap_invalidate_page to invalidate entry x.
finished, entry x and its zbud is not freed as its refcount != 0
now, the swap_map[x] = 0
thread 0: now call zswap_get_swap_cache_page
swapcache_prepare return -ENOENT because entry x is not used any more
zswap_get_swap_cache_page return ZSWAP_SWAPCACHE_NOMEM
zswap_writeback_entry do nothing except put refcount
Now, the memory of zswap_entry x and its zpage leak.
Modify:
- check the refcount in fail path, free memory if it is not referenced.
- use ZSWAP_SWAPCACHE_FAIL instead of ZSWAP_SWAPCACHE_NOMEM as the fail path
can be not only caused by nomem but also by invalidate.
Cyrill Gorcunov [Wed, 16 Oct 2013 20:46:53 +0000 (13:46 -0700)]
mm: /proc/pid/pagemap: inspect _PAGE_SOFT_DIRTY only on present pages
If a page we are inspecting is in swap we may occasionally report it as
having soft dirty bit (even if it is clean). The pte_soft_dirty helper
should be called on present pte only.
Cyrill Gorcunov [Wed, 16 Oct 2013 20:46:51 +0000 (13:46 -0700)]
mm: migration: do not lose soft dirty bit if page is in migration state
If page migration is turned on in config and the page is migrating, we
may lose the soft dirty bit. If fork and mprotect are called on
migrating pages (once migration is complete) pages do not obtain the
soft dirty bit in the correspond pte entries. Fix it adding an
appropriate test on swap entries.
Joonsoo Kim [Wed, 16 Oct 2013 20:46:48 +0000 (13:46 -0700)]
mm/hugetlb.c: correct missing private flag clearing
We should clear the page's private flag when returing the page to the
hugepage pool. Otherwise, marked hugepage can be allocated to the user
who tries to allocate the non-reserved hugepage. If this user fail to
map this hugepage, he would try to return the page to the hugepage pool.
Since this page has a private flag, resv_huge_pages would mistakenly
increase. This patch fixes this situation.
Manfred Spraul [Wed, 16 Oct 2013 20:46:45 +0000 (13:46 -0700)]
ipc/sem.c: synchronize semop and semctl with IPC_RMID
After acquiring the semlock spinlock, operations must test that the
array is still valid.
- semctl() and exit_sem() would walk stale linked lists (ugly, but
should be ok: all lists are empty)
- semtimedop() would sleep forever - and if woken up due to a signal -
access memory after free.
The patch also:
- standardizes the tests for .deleted, so that all tests in one
function leave the function with the same approach.
- unconditionally tests for .deleted immediately after every call to
sem_lock - even it it means that for semctl(GETALL), .deleted will be
tested twice.
Both changes make the review simpler: After every sem_lock, there must
be a test of .deleted, followed by a goto to the cleanup code (if the
function uses "goto cleanup").
The only exception is semctl_down(): If sem_ids().rwsem is locked, then
the presence in ids->ipcs_idr is equivalent to !.deleted, thus no
additional test is required.
David Rientjes [Wed, 16 Oct 2013 20:46:43 +0000 (13:46 -0700)]
mm, memcg: protect mem_cgroup_read_events for cpu hotplug
for_each_online_cpu() needs the protection of {get,put}_online_cpus() so
cpu_online_mask doesn't change during the iteration.
cpu_hotplug.lock is held while a cpu is going down, it's a coarse lock
that is used kernel-wide to synchronize cpu hotplug activity. Memcg has
a cpu hotplug notifier, called while there may not be any cpu hotplug
refcounts, which drains per-cpu event counts to memcg->nocpu_base.events
to maintain a cumulative event count as cpus disappear. Without
get_online_cpus() in mem_cgroup_read_events(), it's possible to account
for the event count on a dying cpu twice, and this value may be
significantly large.
In fact, all memcg->pcp_counter_lock use should be nested by
{get,put}_online_cpus().
This fixes that issue and ensures the reported statistics are not vastly
over-reported during cpu hotplug.
driver core: Release device_hotplug_lock when store_mem_state returns EINVAL
When inserting a wrong value to /sys/devices/system/memory/memoryX/state file,
following messages are shown. And device_hotplug_lock is never released.
================================================
[ BUG: lock held when returning to user space! ]
3.12.0-rc4-debug+ #3 Tainted: G W
------------------------------------------------
bash/6442 is leaving the kernel with locks still held!
1 lock held by bash/6442:
#0: (device_hotplug_lock){+.+.+.}, at: [<ffffffff8146cbb5>] lock_device_hotplug_sysfs+0x15/0x50
This issue was introdued by commit fa2be40 (drivers: base: use standard
device online/offline for state change).
This patch releases device_hotplug_lcok when store_mem_state returns EINVAL.
Linus Torvalds [Thu, 17 Oct 2013 00:16:57 +0000 (17:16 -0700)]
Merge tag 'dm-3.12-fix-cve' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fix from Alasdair Kergon:
"A patch to avoid data corruption in a device-mapper snapshot.
This is primarily a data corruption bug that all users of
device-mapper snapshots will want to fix. The CVE is due to a data
leak under specific circumstances if, for example, the snapshot is
presented to a virtual machine: a block written as data inside the VM
can get interpreted incorrectly on the host outside the VM as
metadata, causing the host to provide the VM with access to blocks it
would not otherwise see. This is likely to affect few, if any,
people"
* tag 'dm-3.12-fix-cve' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm snapshot: fix data corruption
Linus Torvalds [Thu, 17 Oct 2013 00:15:57 +0000 (17:15 -0700)]
Merge tag 'gpio-v3.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"Three GPIO fixes for the v3.12 series:
- A fix to the Lynxpoint IRQ handler
- Two late fixes to fallout from the gpiod refactoring"
* tag 'gpio-v3.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: let gpiod_request() return -EPROBE_DEFER
gpiolib: safer implementation of desc_to_gpio()
gpio/lynxpoint: check if the interrupt is enabled in IRQ handler
Charles Keepax [Mon, 14 Oct 2013 18:36:47 +0000 (19:36 +0100)]
cpufreq: s3c64xx: Rename index to driver_data
The index field of cpufreq_frequency_table has been renamed to
driver_data by commit 5070158 (cpufreq: rename index as driver_data
in cpufreq_frequency_table).
ACPI / power: Drop automaitc resume of power resource dependent devices
The mechanism causing devices depending on a given power resource
(that is, devices that can be in D0 only if that power resource is
on) to be resumed automatically when the power resource is turned
on (and their "inferred" power state becomes D0 as a result) is
inherently racy and in fact unnecessary.
It is racy, because if the power resource is turned on and then
immediately off, the device resume triggered by the first transition
to "on" may still happen, causing the power resource to be turned
on again. That again will trigger the "resume of dependent devices"
mechanism, but if the devices in question are not in use, they will
be suspended in the meantime causing the power resource to be turned
off. However, the "resume of dependent devices" will next resume
them again and so on. In some cases (USB port PM in particular) that
leads to an endless busy loop of flipping the resource on and off
continuously.
It is needless, because whoever turns a power resource on will most
likely turn it off at some point and the devices that go into "D0"
as a result of turning it on will then go back into D3cold
(generally, the state they were in before).
Moreover, turning on all power resources a device needs to go into
D0 is not sufficient for a full transition into D0 in general.
Namely, _PS0 may need to be executed in addition to that in some
cases. This means that the whole rationale of the "resume of
dependent devices" mechanism was incorrect to begin with and it's
best to remove it entirely.
Matthew Dawson [Wed, 16 Oct 2013 04:11:24 +0000 (00:11 -0400)]
usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
The USB3503 driver had an incorrect depedency on REGMAP, instead of
REGMAP_I2C. This caused the build to fail since the necessary regmap
i2c pieces were not available.
Oliver Neukum [Mon, 14 Oct 2013 13:24:55 +0000 (15:24 +0200)]
usb-storage: add quirk for mandatory READ_CAPACITY_16
Some USB drive enclosures do not correctly report an
overflow condition if they hold a drive with a capacity
over 2TB and are confronted with a READ_CAPACITY_10.
They answer with their capacity modulo 2TB.
The generic layer cannot cope with that. It must be told
to use READ_CAPACITY_16 from the beginning.
Roel Kluin [Mon, 14 Oct 2013 21:21:15 +0000 (23:21 +0200)]
serial: vt8500: add missing braces
Due to missing braces on an if statement, in presence of a device_node a
port was always assigned -1, regardless of any alias entries in the
device tree. Conversely, if device_node was NULL, an unitialized port
ended up being used.
This patch adds the missing braces, fixing the issues.
Mikulas Patocka [Wed, 16 Oct 2013 02:17:47 +0000 (03:17 +0100)]
dm snapshot: fix data corruption
This patch fixes a particular type of data corruption that has been
encountered when loading a snapshot's metadata from disk.
When we allocate a new chunk in persistent_prepare, we increment
ps->next_free and we make sure that it doesn't point to a metadata area
by further incrementing it if necessary.
When we load metadata from disk on device activation, ps->next_free is
positioned after the last used data chunk. However, if this last used
data chunk is followed by a metadata area, ps->next_free is positioned
erroneously to the metadata area. A newly-allocated chunk is placed at
the same location as the metadata area, resulting in data or metadata
corruption.
This patch changes the code so that ps->next_free skips the metadata
area when metadata are loaded in function read_exceptions.
The patch also moves a piece of code from persistent_prepare_exception
to a separate function skip_metadata to avoid code duplication.
John Johansen [Mon, 14 Oct 2013 18:46:27 +0000 (11:46 -0700)]
apparmor: fix bad lock balance when introspecting policy
BugLink: http://bugs.launchpad.net/bugs/1235977
The profile introspection seq file has a locking bug when policy is viewed
from a virtual root (task in a policy namespace), introspection from the
real root is not affected.
The test for root
while (parent) {
is correct for the real root, but incorrect for tasks in a policy namespace.
This allows the task to walk backup the policy tree past its virtual root
causing it to be unlocked before the virtual root should be in the p_stop
fn.
This results in the following lockdep back trace:
[ 78.479744] [ BUG: bad unlock balance detected! ]
[ 78.479792] 3.11.0-11-generic #17 Not tainted
[ 78.479838] -------------------------------------
[ 78.479885] grep/2223 is trying to release lock (&ns->lock) at:
[ 78.479952] [<ffffffff817bf3be>] mutex_unlock+0xe/0x10
[ 78.480002] but there are no more locks to release!
[ 78.480037]
[ 78.480037] other info that might help us debug this:
[ 78.480037] 1 lock held by grep/2223:
[ 78.480037] #0: (&p->lock){+.+.+.}, at: [<ffffffff812111bd>] seq_read+0x3d/0x3d0
[ 78.480037]
[ 78.480037] stack backtrace:
[ 78.480037] CPU: 0 PID: 2223 Comm: grep Not tainted 3.11.0-11-generic #17
[ 78.480037] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 78.480037] ffffffff817bf3beffff880007763d60ffffffff817b97efffff8800189d2190
[ 78.480037] ffff880007763d88ffffffff810e1c6effff88001f044730ffff8800189d2190
[ 78.480037] ffffffff817bf3beffff880007763e00ffffffff810e5bd60000000724fe56b7
[ 78.480037] Call Trace:
[ 78.480037] [<ffffffff817bf3be>] ? mutex_unlock+0xe/0x10
[ 78.480037] [<ffffffff817b97ef>] dump_stack+0x54/0x74
[ 78.480037] [<ffffffff810e1c6e>] print_unlock_imbalance_bug+0xee/0x100
[ 78.480037] [<ffffffff817bf3be>] ? mutex_unlock+0xe/0x10
[ 78.480037] [<ffffffff810e5bd6>] lock_release_non_nested+0x226/0x300
[ 78.480037] [<ffffffff817bf2fe>] ? __mutex_unlock_slowpath+0xce/0x180
[ 78.480037] [<ffffffff817bf3be>] ? mutex_unlock+0xe/0x10
[ 78.480037] [<ffffffff810e5d5c>] lock_release+0xac/0x310
[ 78.480037] [<ffffffff817bf2b3>] __mutex_unlock_slowpath+0x83/0x180
[ 78.480037] [<ffffffff817bf3be>] mutex_unlock+0xe/0x10
[ 78.480037] [<ffffffff81376c91>] p_stop+0x51/0x90
[ 78.480037] [<ffffffff81211408>] seq_read+0x288/0x3d0
[ 78.480037] [<ffffffff811e9d9e>] vfs_read+0x9e/0x170
[ 78.480037] [<ffffffff811ea8cc>] SyS_read+0x4c/0xa0
[ 78.480037] [<ffffffff817ccc9d>] system_call_fastpath+0x1a/0x1f
Linus Torvalds [Wed, 16 Oct 2013 00:14:13 +0000 (17:14 -0700)]
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree fixes and reverts from Grant Likely:
"One bug fix and three reverts. The reverts back out the slightly
controversial feeding the entire device tree into the random pool and
the reserved-memory binding which isn't fully baked yet. Expect the
reserved-memory patches at least to resurface for v3.13.
The bug fixes removes a scary but harmless warning on SPARC that was
introduced in the v3.12 merge window. v3.13 will contain a proper fix
that makes the new code work on SPARC.
On the plus side, the diffstat looks *awesome*. I love removing lines
of code"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
Revert "drivers: of: add initialization code for dma reserved memory"
Revert "ARM: init: add support for reserved memory defined by device tree"
Revert "of: Feed entire flattened device tree into the random pool"
of: fix unnecessary warning on missing /cpus node
Dirk Brandewie [Tue, 15 Oct 2013 18:06:14 +0000 (11:06 -0700)]
cpufreq / intel_pstate: Fix max_perf_pct on resume
If the system is suspended while max_perf_pct is less than 100 percent
or no_turbo set policy->{min,max} will be set incorrectly with scaled
values which turn the scaled values into hard limits.
Linus Torvalds [Tue, 15 Oct 2013 23:22:11 +0000 (16:22 -0700)]
Merge tag 'stable/for-linus-3.12-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Stefano Stabellini:
"A small fix for Xen on x86_32 and a build fix for xen-tpmfront on
arm64"
* tag 'stable/for-linus-3.12-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix possible user space selector corruption
tpm: xen-tpmfront: fix missing declaration of xen_domain
Lan Tianyu [Tue, 15 Oct 2013 11:48:11 +0000 (19:48 +0800)]
ACPI / power: Release resource_lock after acpi_power_get_state() return error
In acpi_resume_power_resources() resource_lock should be released
when acpi_power_get_state() fails and before passing to next power
resource on the list.
DRI clients that tried to grab the TTM lock when the master (X server) was
switched away during a VT switch were sent the SIGTERM signal by the
kernel. Fix this so that they are only sent that signal when the master has
exited.
iio:buffer: Free active scan mask in iio_disable_all_buffers()
Usually the active scan mask is freed in __iio_update_buffers() when the buffer
is disabled. But when the device is still sampling when it is removed we'll end
up disabling the buffers in iio_disable_all_buffers(). So we also need to free
the active scan mask here, otherwise it will be leaked.
drivers: thermal: allow ti-soc-thermal run without pcb zone
This patch changes the behavior of TI SoC thermal driver
when there is a PCB thermal zone.
Instead of reporting an error code when reading from
PCB temperature sensor fails, this patch will make
the driver attempt to compose the hotspot extrapolation
based on bandgap readings only.
Lukasz Majewski [Wed, 9 Oct 2013 06:29:52 +0000 (08:29 +0200)]
thermal: exynos: Provide initial setting for TMU's test MUX address at Exynos4412
The commit d0a0ce3e77c795258d47f9163e92d5031d0c5221 ("thermal: exynos: Add
missing definations and code cleanup") has removed setting of test MUX address
value at TMU configuration setting.
This field is not present on Exynos4210 and Exynos5 SoCs. However on Exynos4412
SoC it is required to set this field after reset because without it TMU shows
maximal available temperature, which causes immediate platform shutdown.
Lukasz Majewski [Wed, 9 Oct 2013 06:29:51 +0000 (08:29 +0200)]
thermal: exynos: Provide separate TMU data for Exynos4412
Up till now Exynos5250 and Exynos4412 had the same definitions for TMU
data. Following commit changes that, by introducing separate
exynos4412_default_tmu_data structure.
Since Exynos4412 was chronologically first, the corresponding name for
TMU registers and default data was renamed.
Additionally, new SOC_ARCH_EXYNOS4412 type has been defined.
Moreover, the SOC_ARCH_EXYNOS name has been changed to SOC_ARCH_EXYNOS5250.
Lukasz Majewski [Wed, 9 Oct 2013 06:29:50 +0000 (08:29 +0200)]
thermal: exynos: Remove check for thermal device pointer at exynos_report_trigger()
The commit 4de0bdaa9677d11406c9becb70c60887c957e1f0
("thermal: exynos: Add support for instance based register/unregister")
broke check for presence of therm_dev at global thermal zone in
exynos_report_trigger().
The resulting wrong test prevents thermal_zone_device_update() call, which
calls handlers for situation when trip points are passed.
Such behavior prevents thermal driver from proper reaction (when TMU interrupt
is raised) in a situation when overheating is detected at TMU hardware.
It turns out, that after exynos thermal subsystem redesign (at v3.12) this
check is not needed, since it is not possible to register thermal zone
without valid thermal device.
Lukasz Dorau [Mon, 14 Oct 2013 16:18:53 +0000 (18:18 +0200)]
libahci: fix turning on LEDs in ahci_start_port()
If EM Transmit bit is busy during init ata_msleep() is called. It is
wrong - msleep() should be used instead of ata_msleep(), because if EM
Transmit bit is busy for one port, it will be busy for all other ports
too, so using ata_msleep() causes wasting tries for another ports.
The most common scenario looks like that now
(six ports try to transmit a LED meaasege):
- port #0 tries for the 1st time and succeeds
- ports #1-5 try for the 1st time and sleeps
- port #1 tries for the 2nd time and succeeds
- ports #2-5 try for the 2nd time and sleeps
- port #2 tries for the 3rd time and succeeds
- ports #3-5 try for the 3rd time and sleeps
- port #3 tries for the 4th time and succeeds
- ports #4-5 try for the 4th time and sleeps
- port #4 tries for the 5th time and succeeds
- port #5 tries for the 5th time and sleeps
At this moment port #5 wasted all its five tries and failed to
initialize. Because there are only 5 (EM_MAX_RETRY) tries available
usually only five ports succeed to initialize. The sixth port and next
ones usually will fail.
If msleep() is used instead of ata_msleep() the first port succeeds to
initialize in the first try and next ones usually succeed to
initialize in the second try.
projects / linux.git / log