Merge tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Build fix for omap_hsmmc with OF against 3.4-rc1.
- Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3, which
broke hotplug card detection when UNSAFE_RESUME is set.
- Fix a race condition in omap_hsmmc with runtime PM.
- Fix two libertas SDIO-powered-resume regressions.
- Small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
* tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: core: Do not pre-claim host in suspend
mmc: dw_mmc: prevent NULL dereference for dma_ops
mmc: unbreak sdhci-esdhc-imx on i.MX25
mmc: cd-gpio: Include header to pickup exported symbol prototypes
mmc: sdhci: refine non-removable card checking for card detection
mmc: dw_mmc: Fix switch from DMA to PIO
mmc: remove MMC bus legacy suspend/resume method
mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage
mmc: omap_hsmmc: build fix for CONFIG_OF=y and CONFIG_MMC_OMAP_HS=m
mmc: fixes for eMMC v4.5 sanitize operation
mmc: fixes for eMMC v4.5 discard operation
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on
Kaffeine (Fedora 16 Bugzilla #812895);
- Fixes a mutex unlock at an error condition at drx-k;
- Fix winbond-cir set mode;
- mt9m032: Fix a compilation breakage with some random Kconfig;
- mt9m032: fix two dead locks;
- xc5000: don't require an special firmware (that won't be provided by
the vendor) just because the xtal frequency is different;
- V4L DocBook: fix some typos at multi-plane formats description.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
[media] V4L: mt9m032: fix compilation breakage
[media] V4L: DocBook: Fix typos in the multi-plane formats description
[media] V4L: mt9m032: fix two dead-locks
[media] rc-core: set mode for winbond-cir
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
[media] dvb_frontend: Fix a regression when switching back to DVB-S
Merge tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
Wenqi Ma [Thu, 19 Apr 2012 00:39:37 +0000 (00:39 +0000)]
net/hyperv: Adding cancellation to ensure rndis filter is closed
Although the network interface is down, the RX packets number which
could be observed by ifconfig may keep on increasing.
This is because the WORK scheduled in netvsc_set_multicast_list()
may be executed after netvsc_close(). That means the rndis filter
may be re-enabled by do_set_multicast() even if it was closed by
netvsc_close().
By canceling possible WORK before close the rndis filter, the issue
could be never happened.
Stephen Boyd [Wed, 18 Apr 2012 17:25:58 +0000 (17:25 +0000)]
ks8851: Fix mutex deadlock in ks8851_net_stop()
There is a potential deadlock scenario when the ks8851 driver
is removed. The interrupt handler schedules a workqueue which
acquires a mutex that ks8851_net_stop() also acquires before
flushing the workqueue. Previously lockdep wouldn't be able
to find this problem but now that it has the support we can
trigger this lockdep warning by rmmoding the driver after
an ifconfig up.
Fix the possible deadlock by disabling the interrupts in
the chip and then release the lock across the workqueue
flushing. The mutex is only there to proect the registers
anyway so this should be ok.
=======================================================
[ INFO: possible circular locking dependency detected ] 3.0.21-00021-g8b33780-dirty #2911
-------------------------------------------------------
rmmod/125 is trying to acquire lock:
((&ks->irq_work)){+.+...}, at: [<c019e0b8>] flush_work+0x0/0xac
but task is already holding lock:
(&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Al Viro [Sat, 21 Apr 2012 01:49:41 +0000 (21:49 -0400)]
aio: don't bother with unmapping when aio_free_ring() is coming from exit_aio()
... since exit_mmap() is coming and it will munmap() everything anyway.
In all other cases aio_free_ring() has ctx->mm == current->mm; moreover,
all other callers of vm_munmap() have mm == current->mm, so this will
allow us to get rid of mm argument of vm_munmap().
The NFSv4 spec is ambiguous about whether or not it is permissible
to reuse open owner names, so play it safe. This patch adds a timestamp
to the state_owner structure, and combines that with the IDA based
uniquifier.
Fixes a regression whereby the Linux server returns NFS4ERR_BAD_SEQID.
Thomas Abraham [Sat, 21 Apr 2012 00:26:23 +0000 (17:26 -0700)]
ARM: EXYNOS: Fix incorrect initialization of GIC
Use the of_irq_init() call to setup the gic which also properly
registers the gic device node pointer with gic irq domain,
without which all interrupt specifier translations for gic fail.
Eric Bénard [Wed, 18 Apr 2012 00:30:20 +0000 (02:30 +0200)]
mmc: unbreak sdhci-esdhc-imx on i.MX25
This was broken by me in 37865fe91582582a6f6c00652f6a2b1ff71f8a78
("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more
extensive tests would have shown that read or write of data to the
card were failing (even if the partition table was correctly read).
Daniel Drake [Mon, 9 Apr 2012 23:14:20 +0000 (00:14 +0100)]
mmc: sdhci: refine non-removable card checking for card detection
Commit c79396c191bc19 ("mmc: sdhci: prevent card detection activity
for non-removable cards") disables card detection where the cards
are marked as non-removable.
This makes sense, but the implementation detail of calling
mmc_card_is_removable() causes some problems, because
mmc_card_is_removable() is overloaded with CONFIG_MMC_UNSAFE_RESUME
semantics.
In the OLPC XO case, we need CONFIG_MMC_UNSAFE_RESUME because our root
filesystem is stored on SD, but we also have external SD card slots
where we want automatic card detection.
Refine the check to only apply to hosts marked as MMC_CAP_NONREMOVABLE,
which is defined to mean that the card is *really* nonremovable. This
could be revisited in future if we find a way to improve
CONFIG_MMC_UNSAFE_RESUME semantics.
When dw_mci_pre_dma_transfer returns failure in some reasons,
dw_mci_submit_data will prepare to switch the PIO mode from DMA.
After switching to PIO mode, DMA(IDMAC in particular) is still
enabled. This makes the corruption in handling interrupt and
the driver lock-up.
MMC bus is using legacy suspend/resume method, which is not compatible if
runtime pm callbacks are used. In this scenario, MMC bus suspend/resume
callbacks cannot be called when system entering S3. So change to use the
new defined dev_pm_ops for system sleeping mode.
Tested on AM335x Platform. Solves major issue/crash reported at
http://www.mail-archive.com/[email protected]/msg65425.html
This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.
This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c. But that way we don't have
to export our internal do_mmap_pgoff() function.
Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead. We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage
of_have_populated_dt() is not expected to be used in drivers but
instead only in early platform init code.
Drivers on the other hand should rely on dev->of_node or of_match_device().
Besides usage of of_have_populated_dt() also throws up build error as below
which was reported by Balaji TK, when omap_hsmmc is built as a module.
Adrian Hunter [Thu, 5 Apr 2012 11:45:48 +0000 (14:45 +0300)]
mmc: fixes for eMMC v4.5 sanitize operation
eMMC v4.5 sanitize operation erases all copies of unmapped
data. However trim or erase operations must be used first
to unmap the required sectors. That was not being done.
Adrian Hunter [Thu, 5 Apr 2012 11:45:47 +0000 (14:45 +0300)]
mmc: fixes for eMMC v4.5 discard operation
eMMC v4.5 discard operation is significantly different from the
existing trim operation because it is not guaranteed to work with
the new sanitize operation. Consequently mmc_can_trim() is
separated from mmc_can_discard().
Also the new discard operation does not result in the sectors being
set to all-zeros, so discard_zeroes_data must not be set.
In addition, the new discard has the same timeout as trim, but from
v4.5 trim is defined to use the hc timeout. The timeout calculation
is adjusted accordingly.
Thomas Abraham [Sat, 14 Apr 2012 15:04:46 +0000 (08:04 -0700)]
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
With the addition of platform specific driver data in the sdhci driver
for EXYNOS4 and EXYNOS5, the device name of sdhci controllers on EXYNOS4
and EXYNOS5 are changed accordingly.
Jan Kara [Fri, 2 Sep 2011 23:09:43 +0000 (01:09 +0200)]
nfs: Enclose hostname in brackets when needed in nfs_do_root_mount
When hostname contains colon (e.g. when it is an IPv6 address) it needs
to be enclosed in brackets to make parsing of NFS device string possible.
Fix nfs_do_root_mount() to enclose hostname properly when needed. NFS code
actually does not need this as it does not parse the string passed by
nfs_do_root_mount() but the device string is exposed to userspace in
/proc/mounts.
Merge tag 'for-torvalds-20120418' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- Fixed compilation errors and warnings
- Stricter checks on the ops vtable
* tag 'for-torvalds-20120418' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: implement pinctrl_check_ops
pinctrl: include <linux/bug.h> to prevent compile errors
pinctrl: fix compile error if not select PINMUX support
Merge tag 'tty-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull 3 tiny tty bugfixes from Greg Kroah-Hartman.
* tag 'tty-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
drivers/tty/amiserial.c: add missing tty_unlock
pch_uart: Fix dma channel unallocated issue
ARM: clps711x: serial driver hungs are a result of call disable_irq within ISR
Merge tag 'stable/for-linus-3.4-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
- mechanism to work with misconfigured backends (where they are
advertised but in reality don't exist).
- two tiny compile warning fixes.
- proper error handling in gnttab_resume
- Not using VM_PFNMAP anymore to allow backends in the same domain.
* tag 'stable/for-linus-3.4-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
Revert "xen/p2m: m2p_find_override: use list_for_each_entry_safe"
xen/resume: Fix compile warnings.
xen/xenbus: Add quirk to deal with misconfigured backends.
xen/blkback: Fix warning error.
xen/p2m: m2p_find_override: use list_for_each_entry_safe
xen/gntdev: do not set VM_PFNMAP
xen/grant-table: add error-handling code on failure of gnttab_resume
It breaks reboot on at least one Thinkpad T43, as reported by Jörg Otte:
"On reboot it shuts down as normal.
The last lines displayed are:
>Unmounting temporary filesystems.. [OK]
>Deactivating swap... [OK]
>Unmounting local filesystems... [OK]
>Will now restart
> Restarting system
Then I hear it accessing the cd-drive, but then it's being stuck."
Jörg bisected the regression to this commit.
That commit fixes another machine (see
https://bugzilla.kernel.org/show_bug.cgi?id=11533
for details) that has a BIOS bug and doesn't support ACPI reset.
However, at least one of those other reporters no longer even has the
machine in question, and had a different workaround to begin with.
Besides, it clearly was a buggy BIOS. Let's not break the correct case
to fix that case.
memblock: memblock should be able to handle zero length operations
Commit 24aa07882b ("memblock, x86: Replace memblock_x86_reserve/
free_range() with generic ones") replaced x86 specific memblock
operations with the generic ones; unfortunately, it lost zero length
operation handling in the process making the kernel panic if somebody
tries to reserve zero length area.
There isn't much to be gained by being cranky to zero length operations
and panicking is almost the worst response. Drop the BUG_ON() in
memblock_reserve() and update memblock_add_region/isolate_range() so
that all zero length operations are handled as noops.
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pyll hwmon fixes from Guenter Roeck:
"Two patches: Fix build warning in ads1015 driver, and fix bogus power
values with current BIOSes in fam15h_power driver."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ads1015) Fix build warning
hwmon: fam15h_power: fix bogus values with current BIOSes
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Fixes for a few regressions of HD-audio, originated partly from 3.4
and partly 3.3.
The fixes for ThinkPad docking-station are for 3.3 kernels, thus they
are based on 3.3 then merged back to 3.4, so that they can be merged
to stable tree cleanly. The non-trivial merge conflicts are because
of this action.
In addition, a couple of trivial fixes for documentation and a long-
standing issue in the listing of built-in sound driver at boot time."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/conexant - Set up the missing docking-station pins
ALSA: hda/conexant - Don't set HP pin-control bit unconditionally
ALSA: workaround: change the timing of alsa_sound_last_init()
ALSA: hda/sigmatel - Fix inverted mute LED
ALSA: hda/realtek - Fix regression on Quanta/Gericom KN1
ALSA: fix core/vmaster.c kernel-doc warning
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"Fix for one particular device (bluetooth Tivo Slide) and change of
'default y' -> 'default n' for CONFIG_HID_BATTERY_STRENGTH which I
overlooked in the initial merge of the battery support"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: default HID_BATTERY_STRENGTH to no
HID: tivo: fix support for bluetooth version of tivo Slide
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68k arch fixes from Greg Ungerer:
"This contains four fixes for 3.4. Two fix and clean up compilation
for the nommu 68x328 CPU targets. The other two fix the platform
definition and multi-function pin setup of the second eth interface
on the ColdFire 5275 SoC."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: make sure 2nd FEC eth interface pins are enabled on 5275 ColdFire
m68knommu: fix id number for second eth device on 5275 ColdFire
m68knommu: move and fix the 68VZ328 platform bootlogo.h
m68knommu: remove the unused bootlogo.h processing for 68EZ328 and 68VZ328
Jiri Olsa [Wed, 18 Apr 2012 13:46:58 +0000 (15:46 +0200)]
perf symbols: Read plt symbols from proper symtab_type binary
When loading symbols from DSO we check multiple paths of DSO binary
until we succeed to load symbols ('.symtab' section). Once symbols are
read we try to load also plt symbols.
During the reading of plt symbols, the dso file is reopened from
location given by dso->long_name. This could be wrong in case we want
process buildid binaries.
The change is to make the plt symbols being read from the DSO path, that
normal symbols were read from.
If we have another thread (very likely) touched the list, we
end up hitting a problem "that the next element is wrong because
we should be able to cope with that. The problem is that the
next->next pointer would be set LIST_POISON1. " (Stefano's
comment on the patch).
Fixed too small hardcoded timeout values for usb_control_msg
in driver for SiliconLabs cp210x-based usb-to-serial adapters.
Replaced with USB_CTRL_GET_TIMEOUT/USB_CTRL_SET_TIMEOUT.
Nicolas Ferre [Mon, 16 Apr 2012 12:46:30 +0000 (14:46 +0200)]
dmaengine: at_hdmac: remove clear-on-read in atc_dostart()
This loop on EBCISR register was designed to clear IRQ sources before enabling
a DMA channel. This register is clear-on-read so a race condition can appear if
another channel is already active and has just finished its transfer.
Removing this read on EBCISR is fixing the issue as there is no case where an IRQ
could be pending: we already make sure that this register is drained at probe()
time and during resume.
ALSA: HDA: Add external mic quirk for Asus Zenbook UX31E
According to the reporter, external mic starts to work if the
laptop-dmic model is used. According to BIOS pin config, all
pins are consistent with the alc269vb_laptop_dmic fixup, except
for the external mic, which is not present.
Since the VIC was converted to use generic IRQ domains IRQ 0
is silently ignored. This IRQ is used on the U300 so we're
missing it now. Bump all IRQ numbers by one since they are
now decoupled from the hardware IRQ numbers.
It doesn't make sense to grant permission to change the status of a
regulator that is also set as always on and similarly it doesn't make
sense to allow a driver to change the voltage of a regulator which can
only be set to a single voltage.
Jeff Layton [Fri, 13 Apr 2012 21:16:59 +0000 (17:16 -0400)]
cifs: fix offset handling in cifs_iovec_write
In the recent update of the cifs_iovec_write code to use async writes,
the handling of the file position was broken. That patch added a local
"offset" variable to handle the offset, and then only updated the
original "*poffset" before exiting.
Unfortunately, it copied off the original offset from the beginning,
instead of doing so after generic_write_checks had been called. Fix
this by moving the initialization of "offset" after that in the
function.
Merge branch 'for-3.4' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from J. Bruce Fields:
"One bugfix, and one minor header fix from Jeff Layton while we're
here"
* 'for-3.4' of git://linux-nfs.org/~bfields/linux:
nfsd: include cld.h in the headers_install target
nfsd: don't fail unchecked creates of non-special files
Steven Rostedt [Thu, 19 Apr 2012 14:31:47 +0000 (10:31 -0400)]
tracing: Fix stacktrace of latency tracers (irqsoff and friends)
While debugging a latency with someone on IRC (mirage335) on #linux-rt (OFTC),
we discovered that the stacktrace output of the latency tracers
(preemptirqsoff) was empty.
This bug was caused by the creation of the dynamic length stack trace
again (like commit 12b5da3 "tracing: Fix ent_size in trace output" was).
This bug is caused by the latency tracers requiring the next event
to determine the time between the current event and the next. But by
grabbing the next event, the iter->ent_size is set to the next event
instead of the current one. As the stacktrace event is the last event,
this makes the ent_size zero and causes nothing to be printed for
the stack trace. The dynamic stacktrace uses the ent_size to determine
how much of the stack can be printed. The ent_size of zero means
no stack.
The simple fix is to save the iter->ent_size before finding the next event.
Note, mirage335 asked to remain anonymous from LKML and git, so I will
not add the Reported-by and Tested-by tags, even though he did report
the issue and tested the fix.
Mingkai Hu [Mon, 16 Apr 2012 02:05:06 +0000 (10:05 +0800)]
powerpc/mpic_msgr: add lock for MPIC message global variable
Also fix issue of accessing invalid msgr pointer issue. The local
msgr pointer in fucntion mpic_msgr_get will be accessed before
getting a valid address which will cause kernel crash.
Mingkai Hu [Mon, 16 Apr 2012 02:05:05 +0000 (10:05 +0800)]
powerpc/mpic_msgr: fix compile error when SMP disabled
In file included from arch/powerpc/sysdev/mpic_msgr.c:20:0:
~/arch/powerpc/include/asm/mpic_msgr.h: In function 'mpic_msgr_set_destination':
~/arch/powerpc/include/asm/mpic_msgr.h:117:2:
error: implicit declaration of function 'get_hard_smp_processor_id'
make[1]: *** [arch/powerpc/sysdev/mpic_msgr.o] Error 1
Commit 46d026ac ("powerpc/85xx: consolidate of_platform_bus_probe calls")
replaced platform-specific of_device_id tables with a single function
that probes the most of the busses in 85xx device trees. If a specific
platform needed additional busses probed, then it could call
of_platform_bus_probe() again. Typically, the additional platform-specific
busses are children of existing busses that have already been probed.
of_platform_bus_probe() does not handle those child busses automatically.
Unfortunately, this doesn't actually work. The second (platform-specific)
call to of_platform_bus_probe() never finds any of the busses it's asked
to find.
To remedy this, the platform-specific of_device_id tables are eliminated,
and their entries are merged into mpc85xx_common_ids[], so that all busses
are probed at once.
While reviewing the sysctl code in ax25 I spotted races in ax25_exit
where it is possible to receive notifications and packets after already
freeing up some of the data structures needed to process those
notifications and updates.
Call unregister_netdevice_notifier early so that the rest of the cleanup
code does not need to deal with network devices. This takes advantage
of my recent enhancement to unregister_netdevice_notifier to send
unregister notifications of all network devices that are current
registered.
Move the unregistration for packet types, socket types and protocol
types before we cleanup any of the ax25 data structures to remove the
possibilities of other races.
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.
tick: Fix the spurious broadcast timer ticks after resume
During resume, tick_resume_broadcast() programs the broadcast timer in
oneshot mode unconditionally. On the platforms where broadcast timer
is not really required, this will generate spurious broadcast timer
ticks upon resume. For example, on the always running apic timer
platforms with HPET, I see spurious hpet tick once every ~5minutes
(which is the 32-bit hpet counter wraparound time).
Similar to boot time, during resume make the oneshot mode setting of
the broadcast clock event device conditional on the state of active
broadcast users.
Thomas Gleixner [Wed, 18 Apr 2012 15:31:58 +0000 (17:31 +0200)]
tick: Ensure that the broadcast device is initialized
Santosh found another trap when we avoid to initialize the broadcast
device in the switch_to_oneshot code. The broadcast device might be
still in SHUTDOWN state when we actually need to use it. That
obviously breaks, as set_next_event() is called on a shutdown
device. This did not break on x86, but Suresh analyzed it:
From the review, most likely on Sven's system we are force enabling
the hpet using the pci quirk's method very late. And in this case,
hpet_clockevent (which will be global_clock_event) handler can be
null, specifically as this platform might not be using deeper c-states
and using the reliable APIC timer.
Prior to commit 'fa4da365bc7772c', that handler will be set to
'tick_handle_oneshot_broadcast' when we switch the broadcast timer to
oneshot mode, even though we don't use it. Post commit
'fa4da365bc7772c', we stopped switching the broadcast mode to oneshot
as this is not really needed and his platform's global_clock_event's
handler will remain null. While on my SNB laptop, same is set to
'clockevents_handle_noop' because hpet gets enabled very early. (noop
handler on my platform set when the early enabled hpet timer gets
replaced by the lapic timer).
But the commit 'fa4da365bc7772c' tracked the broadcast timer mode in
the SW as oneshot, even though it didn't touch the HW timer. During
resume however, tick_resume_broadcast() saw the SW broadcast mode as
oneshot and actually programmed the broadcast device also into oneshot
mode. So this triggered the null pointer de-reference after the hpet
wraps around and depending on what the hpet counter is set to. On the
normal platforms where hpet gets enabled early we should be seeing a
spurious interrupt (in my SNB laptop I see one spurious interrupt
after around 5 minutes ;) which is 32-bit hpet counter wraparound
time), but that's a separate issue.
Enforce the mode setting when trying to set an event.
net: qmi_wwan: support Sierra Wireless MC77xx devices in QMI mode
The MC77xx devices can operate in two modes: "Direct IP" or "QMI",
switchable using a password protected AT command. Both product ID
and USB interface configuration will change when switched.
The "sierra_net" driver supports the "Direct IP" mode. This driver
supports the "QMI" mode.
There are also multiple possible USB interface configurations in each
mode, some providing more than one wwan interface. Like many other
devices made for Windows, different interface types are identified
using a static interface number. We define a Sierra specific
interface whitelist to support this.
Dan Carpenter [Tue, 17 Apr 2012 20:53:42 +0000 (20:53 +0000)]
bnx2x: off by one in bnx2x_ets_e3b0_sp_pri_to_cos_set()
The sp_pri_to_cos[] array size depends on the config but lets say it is
BX_E3B0_MAX_NUM_COS_PORT0 and max_num_of_cos is also
DCBX_E3B0_MAX_NUM_COS_PORT0. In the original code
"pri == max_num_of_cos" was accepted but it is one past the end of the
array.
Also we used "pri" before capping it. It's a harmless read past the end
of the array, but it would affect which error message gets printed.
linux/drivers/xen/manage.c: In function 'do_suspend':
linux/drivers/xen/manage.c:160:5: warning: 'si.cancelled' may be used uninitialized in this function
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"It's like a grab bag of one liners:
- core: fix page flip error path, reorder object teardown.
- usb: fix the drm_usb module license.
- i915: VT switch on SNB with non-native modes fix, and a regression
fix from 3.3.
- radeon: missing unreserve on SI, AGP/VRAM setup fix (fixes radeon on
IA64, but its a generic bug), an rn50 regression from 3.3, turn off
MSIs on rv515 (it loses rearms every so often)."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
nouveau: Set special lane map for the right chipset
drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
drm: Releasing FBs before releasing GEM objects during drm_release
drm/nouveau/pm: don't read/write beyond end of stack buffer
drivers: gpu: drm: gma500: mdfld_dsi_output.h: Remove not unneeded include of version.h
radeon: fix r600/agp when vram is after AGP (v3)
drm: fix page_flip error handling
drm/radeon/kms: fix the regression of DVI connector check
drm/usb: fix module license on drm/usb layer.
drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
drm/i915: Hold mode_config lock whilst changing mode for lastclose()
drm/radeon/si: add missing radeon_bo_unreserve in si_rlc_init() v2
drm/radeon: disable MSI on RV515
drm/i915: don't clobber the special upscaling lvds timings
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1
Linus Walleij says:
| My bad, was because the initial patch was submitted march 9th before
| these fixes were merged:
| http://marc.info/?l=linux-arm-kernel&m=133159655513844&w=2
|
| It was pending for a while in Russell's patch tracker and I
| rebased it to -rc2 without paying enough attention to recent
| related scheduler fixes ... lesson learned.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: lock slots_lock around device assignment
KVM: VMX: Fix kvm_set_shared_msr() called in preemptible context
KVM: unmap pages from the iommu when slots are removed
KVM: PMU emulation: GLOBAL_CTRL MSR should be enabled on reset
Dan Carpenter [Thu, 19 Apr 2012 07:00:19 +0000 (10:00 +0300)]
ksz884x: don't copy too much in netdev_set_mac_address()
MAX_ADDR_LEN is 32. ETH_ALEN is 6. mac->sa_data is a 14 byte array, so
the memcpy() is doing a read past the end of the array. I asked about
this on netdev and Ben Hutchings told me it's supposed to be copying
ETH_ALEN bytes (thanks Ben).
xen/xenbus: Add quirk to deal with misconfigured backends.
A rather annoying and common case is when booting a PVonHVM guest
and exposing the PV KBD and PV VFB - as broken toolstacks don't
always initialize the backends correctly.
Normally The HVM guest is using the VGA driver and the emulated
keyboard for this (though upstream version of QEMU implements
PV KBD, but still uses a VGA driver). We provide a very basic
two-stage wait mechanism - where we wait for 30 seconds for all
devices, and then for 270 for all them except the two mentioned.
That allows us to wait for the essential devices, like network
or disk for the full 6 minutes.
To trigger this, put this in your guest config:
vfb = [ 'vnc=1, vnclisten=0.0.0.0 ,vncunused=1']
instead of this:
vnc=1
vnclisten="0.0.0.0"
CC: [email protected] Acked-by: Stefano Stabellini <[email protected]>
[v3: Split delay in non-essential (30 seconds) and essential
devices per Ian and Stefano suggestion]
[v4: Added comments per Stefano suggestion] Signed-off-by: Konrad Rzeszutek Wilk <[email protected]>
x86, intel_cacheinfo: Fix error return code in amd_set_l3_disable_slot()
If the L3 disable slot is already in use, return -EEXIST instead of
-EINVAL. The caller, store_cache_disable(), checks this return value to
print an appropriate warning.
Also, we want to signal with -EEXIST that the current index we're
disabling has actually been already disabled on the node:
Henrik Rydberg [Thu, 12 Apr 2012 22:37:00 +0000 (00:37 +0200)]
nouveau: Set special lane map for the right chipset
The refactoring of the nv50 logic, introduced in 8663bc7c, modified the
test for the special lane map used on some Apple computers with Nvidia
chipsets. The tested MBA3,1 would still boot, but resume from suspend
stopped working. This patch restores the old test, which fixes the problem.
Merge fixes for Thinkpad docking-station regressions for 3.3 kernels
back to 3.4. These were committed in that branch to make the stable
merging easier.
ALSA: hda/conexant - Set up the missing docking-station pins
ThinkPad 410,420,510,520 and X201 with cx50585 & co chips have the
docking-station ports, but BIOS doesn't initialize for these pins.
Thus, like the former X200, we need to set up the pins manually in the
driver.
The odd part is that the same PCI SSID is used for X200 and T400, thus
we need to prepare individual fixup tables for cx5051 and others.
Dave Airlie [Thu, 19 Apr 2012 14:42:58 +0000 (15:42 +0100)]
drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
When the force changes went in back in 3.3.0, we ended up returning
disconnected in the !force case, and the connected in when forced,
as it hit the hardcoded check.
Fix it so all exits go via the hardcoded check and stop spurious
modesets on platforms with hardcoded EDIDs.
drm: Releasing FBs before releasing GEM objects during drm_release
During DRM release, all the FBs and gem objects are released. If
a gem object is being used as a FB and set to a crtc, it must not
be freed before releasing the framebuffer first.
If FBs are released first, the crtc using the FB is disabled first
so now the GEM object can be freed safely. The CRTC will be enabled
again when the driver restores fbdev mode.
Jim Meyering [Tue, 17 Apr 2012 19:27:54 +0000 (21:27 +0200)]
drm/nouveau/pm: don't read/write beyond end of stack buffer
NUL-terminate after strncpy.
If the parameter "profile" has length 16 or more, then strncpy
leaves "string" with no NUL terminator, so the following search
for '\n' may read beyond the end of that 16-byte buffer.
If it finds a newline there, then it will also write beyond the
end of that stack buffer.
Dave Airlie [Thu, 19 Apr 2012 13:13:52 +0000 (14:13 +0100)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
drm/i915: Hold mode_config lock whilst changing mode for lastclose()
drm/i915: don't clobber the special upscaling lvds timings
drm/radeon/kms: fix the regression of DVI connector check
The check of the encoder type in the commit [e00e8b5e: drm/radeon/kms:
fix analog load detection on DVI-I connectors] is obviously wrong, and
it's the culprit of the regression on my workstation with DVI-analog
connection resulting in the blank output.
Commit 4f5ca836b "HID: hid-input: add support for HID devices reporting
Battery Strength" added the CONFIG_HID_BATTERY_STRENGTH option to report
the battery strength of HID devices. The commit log explicitly mentions
it not working properly with recent userspace, but it is default y
anyway. This is rather odd, and actually causes problems on real
systems.
This works around Fedora bug
https://bugzilla.redhat.com/show_bug.cgi?id=806295
ALSA: workaround: change the timing of alsa_sound_last_init()
Current alsa_sound_last_init() was called as __initcall().
So, on current ALSA, only devices that had been properly
registered at this point were shown.
So, it will show "No soundcards found" if driver requests
probe deferment. it's often misleading.
This patch delays the timing of alsa_sound_last_init()
as workaround.
While refactoring the mute-LED handling for HP laptops, I messed up
the polarity check in a wrong way. The red (or the mute-LED if any)
should appear in the muted state, corresponding to GPIO on.
projects / linux.git / log