scsi: libsas: sas_discover: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: mtx1_defconfig mips):
drivers/scsi/libsas/sas_discover.c: In function ‘sas_discover_domain’:
./include/linux/printk.h:309:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_NOTICE pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/libsas/sas_discover.c:459:3: note: in expansion of macro ‘pr_notice’
pr_notice("ATA device seen but CONFIG_SCSI_SAS_ATA=N so cannot attach\n");
^~~~~~~~~
drivers/scsi/libsas/sas_discover.c:462:2: note: here
default:
^~~~~~~
power: supply: ab8500_charger: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: allmodconfig arm):
drivers/power/supply/ab8500_charger.c: In function ‘ab8500_charger_max_usb_curr’:
drivers/power/supply/ab8500_charger.c:738:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (di->vbus_detected) {
^
drivers/power/supply/ab8500_charger.c:745:2: note: here
case USB_STAT_HM_IDGND:
^~~~
watchdog: wdt285: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: footbridge_defconfig arm):
drivers/watchdog/wdt285.c: In function ‘watchdog_ioctl’:
drivers/watchdog/wdt285.c:170:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
watchdog_ping();
^~~~~~~~~~~~~~~
drivers/watchdog/wdt285.c:172:2: note: here
case WDIOC_GETTIMEOUT:
^~~~
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: assabet_defconfig arm):
drivers/mtd/maps/sa1100-flash.c: In function ‘sa1100_probe_subdev’:
drivers/mtd/maps/sa1100-flash.c:82:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_WARNING "SA1100 flash: unknown base address "
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"0x%08lx, assuming CS0\n", phys);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/maps/sa1100-flash.c:85:2: note: here
case SA1100_CS0_PHYS:
^~~~
drm/sun4i: tcon: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: sunxi_defconfig arm):
drivers/gpu/drm/sun4i/sun4i_tcon.c: In function ‘sun4i_tcon0_mode_set_dithering’:
drivers/gpu/drm/sun4i/sun4i_tcon.c:318:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
val |= SUN4I_TCON0_FRM_CTL_MODE_B;
drivers/gpu/drm/sun4i/sun4i_tcon.c:319:2: note: here
case MEDIA_BUS_FMT_RGB666_1X18:
^~~~
drm/sun4i: sun6i_mipi_dsi: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: multi_v7_defconfig arm):
drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c: In function ‘sun6i_dsi_transfer’:
drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c:993:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (msg->rx_len == 1) {
^
drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c:998:2: note: here
default:
^~~~~~~
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: rpc_defconfig arm):
arch/arm/mach-rpc/riscpc.c: In function ‘parse_tag_acorn’:
arch/arm/mach-rpc/riscpc.c:48:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
vram_size += PAGE_SIZE * 256;
~~~~~~~~~~^~~~~~~~~~~~~~~~~~
arch/arm/mach-rpc/riscpc.c:49:2: note: here
case 256:
^~~~
dmaengine: fsldma: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
Fix the following warnings (Building: powerpc-ppa8548_defconfig powerpc):
drivers/dma/fsldma.c: In function ‘fsl_dma_chan_probe’:
drivers/dma/fsldma.c:1165:26: warning: this statement may fall through [-Wimplicit-fallthrough=]
chan->toggle_ext_pause = fsl_chan_toggle_ext_pause;
~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/dma/fsldma.c:1166:2: note: here
case FSL_DMA_IP_83XX:
^~~~
dma-direct: fix zone selection after an unaddressable CMA allocation
The new dma_alloc_contiguous hides if we allocate CMA or regular
pages, and thus fails to retry a ZONE_NORMAL allocation if the CMA
allocation succeeds but isn't addressable. That means we either fail
outright or dip into a small zone that might not succeed either.
Linus Torvalds [Tue, 20 Aug 2019 18:18:43 +0000 (11:18 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- a few regression fixes for wacom driver (including fix for my earlier
mismerge) from Aaron Armstrong Skomra and Jason Gerecke
- revert of a few Logitech device ID additions which turn out to not
work perfectly with the hidpp driver at the moment; proper support is
now scheduled for 5.4. Fixes from Benjamin Tissoires
- scheduling-in-atomic fix for cp2112 driver, from Benjamin Tissoires
- new device ID to intel-ish, from Even Xu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: wacom: correct misreported EKR ring values
HID: cp2112: prevent sleeping function called from invalid context
HID: intel-ish-hid: ipc: add EHL device id
HID: wacom: Correct distance scale for 2nd-gen Intuos devices
HID: logitech-hidpp: remove support for the G700 over USB
Revert "HID: logitech-hidpp: add USB PID for a few more supported mice"
HID: wacom: add back changes dropped in merge commit
Wenwen Wang [Sun, 18 Aug 2019 18:54:46 +0000 (13:54 -0500)]
infiniband: hfi1: fix memory leaks
In fault_opcodes_write(), 'data' is allocated through kcalloc(). However,
it is not deallocated in the following execution if an error occurs,
leading to memory leaks. To fix this issue, introduce the 'free_data' label
to free 'data' before returning the error.
Wenwen Wang [Sun, 18 Aug 2019 19:29:31 +0000 (14:29 -0500)]
infiniband: hfi1: fix a memory leak bug
In fault_opcodes_read(), 'data' is not deallocated if debugfs_file_get()
fails, leading to a memory leak. To fix this bug, introduce the 'free_data'
label to free 'data' before returning the error.
Wenwen Wang [Sun, 18 Aug 2019 20:23:01 +0000 (15:23 -0500)]
IB/mlx4: Fix memory leaks
In mlx4_ib_alloc_pv_bufs(), 'tun_qp->tx_ring' is allocated through
kcalloc(). However, it is not always deallocated in the following execution
if an error occurs, leading to memory leaks. To fix this issue, free
'tun_qp->tx_ring' whenever an error occurs.
zhengbin [Mon, 19 Aug 2019 04:27:39 +0000 (12:27 +0800)]
RDMA/cma: fix null-ptr-deref Read in cma_cleanup
In cma_init, if cma_configfs_init fails, need to free the
previously memory and return fail, otherwise will trigger
null-ptr-deref Read in cma_cleanup.
Moni Shoua [Thu, 15 Aug 2019 08:38:34 +0000 (11:38 +0300)]
IB/mlx5: Block MR WR if UMR is not possible
Check conditions that are mandatory to post_send UMR WQEs.
1. Modifying page size.
2. Modifying remote atomic permissions if atomic access is required.
If either condition is not fulfilled then fail to post_send() flow.
Moni Shoua [Thu, 15 Aug 2019 08:38:33 +0000 (11:38 +0300)]
IB/mlx5: Fix MR re-registration flow to use UMR properly
The UMR WQE in the MR re-registration flow requires that
modify_atomic and modify_entity_size capabilities are enabled.
Therefore, check that the these capabilities are present before going to
umr flow and go through slow path if not.
Moni Shoua [Thu, 15 Aug 2019 08:38:32 +0000 (11:38 +0300)]
IB/mlx5: Report and handle ODP support properly
ODP depends on the several device capabilities, among them is the ability
to send UMR WQEs with that modify atomic and entity size of the MR.
Therefore, only if all conditions to send such a UMR WQE are met then
driver can report that ODP is supported. Use this check of conditions
in all places where driver needs to know about ODP support.
Also, implicit ODP support depends on ability of driver to send UMR WQEs
for an indirect mkey. Therefore, verify that all conditions to do so are
met when reporting support.
Leon Romanovsky [Thu, 15 Aug 2019 08:38:29 +0000 (11:38 +0300)]
RDMA/restrack: Rewrite PID namespace check to be reliable
task_active_pid_ns() is wrong API to check PID namespace because it
posses some restrictions and return PID namespace where the process
was allocated. It created mismatches with current namespace, which
can be different.
Rewrite whole rdma_is_visible_in_pid_ns() logic to provide reliable
results without any relation to allocated PID namespace.
Leon Romanovsky [Thu, 15 Aug 2019 08:38:28 +0000 (11:38 +0300)]
RDMA/counters: Properly implement PID checks
"Auto" configuration mode is called for visible in that PID
namespace and it ensures that all counters and QPs are coexist
in the same namespace and belong to same PID.
Ido Kalir [Thu, 15 Aug 2019 08:38:27 +0000 (11:38 +0300)]
IB/core: Fix NULL pointer dereference when bind QP to counter
If QP is not visible to the pid, then we try to decrease its reference
count and return from the function before the QP pointer is
initialized. This lead to NULL pointer dereference.
Fix it by pass directly the res to the rdma_restract_put as arg instead of
&qp->res.
Kaike Wan [Thu, 15 Aug 2019 19:20:58 +0000 (15:20 -0400)]
IB/hfi1: Drop stale TID RDMA packets that cause TIDErr
In a congested fabric with adaptive routing enabled, traces show that
packets could be delivered out of order. A stale TID RDMA data packet
could lead to TidErr if the TID entries have been released by duplicate
data packets generated from retries, and subsequently erroneously force
the qp into error state in the current implementation.
Since the payload has already been dropped by hardware, the packet can
be simply dropped and it is no longer necessary to put the qp into
error state.
Kaike Wan [Thu, 15 Aug 2019 19:20:51 +0000 (15:20 -0400)]
IB/hfi1: Add additional checks when handling TID RDMA WRITE DATA packet
In a congested fabric with adaptive routing enabled, traces show that
packets could be delivered out of order, which could cause incorrect
processing of stale packets. For stale TID RDMA WRITE DATA packets that
cause KDETH EFLAGS errors, this patch adds additional checks before
processing the packets.
Kaike Wan [Thu, 15 Aug 2019 19:20:45 +0000 (15:20 -0400)]
IB/hfi1: Add additional checks when handling TID RDMA READ RESP packet
In a congested fabric with adaptive routing enabled, traces show that
packets could be delivered out of order, which could cause incorrect
processing of stale packets. For stale TID RDMA READ RESP packets that
cause KDETH EFLAGS errors, this patch adds additional checks before
processing the packets.
Kaike Wan [Thu, 15 Aug 2019 19:20:39 +0000 (15:20 -0400)]
IB/hfi1: Unsafe PSN checking for TID RDMA READ Resp packet
When processing a TID RDMA READ RESP packet that causes KDETH EFLAGS
errors, the packet's IB PSN is checked against qp->s_last_psn and
qp->s_psn without the protection of qp->s_lock, which is not safe.
This patch fixes the issue by acquiring qp->s_lock first.
Kaike Wan [Thu, 15 Aug 2019 19:20:33 +0000 (15:20 -0400)]
IB/hfi1: Drop stale TID RDMA packets
In a congested fabric with adaptive routing enabled, traces show that
the sender could receive stale TID RDMA NAK packets that contain newer
KDETH PSNs and older Verbs PSNs. If not dropped, these packets could
cause the incorrect rewinding of the software flows and the incorrect
completion of TID RDMA WRITE requests, and eventually leading to memory
corruption and kernel crash.
The current code drops stale TID RDMA ACK/NAK packets solely based
on KDETH PSNs, which may lead to erroneous processing. This patch
fixes the issue by also checking the Verbs PSN. Addition checks are
added before rewinding the TID RDMA WRITE DATA packets.
Jason Gunthorpe [Thu, 15 Aug 2019 08:38:30 +0000 (11:38 +0300)]
RDMA/mlx5: Fix MR npages calculation for IB_ACCESS_HUGETLB
When ODP is enabled with IB_ACCESS_HUGETLB then the required pages
should be calculated based on the extent of the MR, which is rounded
to the nearest huge page alignment.
Jens Axboe [Tue, 20 Aug 2019 17:03:11 +0000 (11:03 -0600)]
io_uring: don't enter poll loop if we have CQEs pending
We need to check if we have CQEs pending before starting a poll loop,
as those could be the events we will be spinning for (and hence we'll
find none). This can happen if a CQE triggers an error, or if it is
found by eg an IRQ before we get a chance to find it through polling.
nvme: Add quirk for LiteON CL1 devices running FW 22301111
One of the components in LiteON CL1 device has limitations that
can be encountered based upon boundary race conditions using the
nvme bus specific suspend to idle flow.
When this situation occurs the drive doesn't resume properly from
suspend-to-idle.
LiteON has confirmed this problem and fixed in the next firmware
version. As this firmware is already in the field, avoid running
nvme specific suspend to idle flow.
Commit 1b1031ca63b2 ("nvme: validate cntlid during controller initialisation")
introduced a validation for controllers with duplicate cntlid that runs
on nvme_init_subsystem(). The problem is that the validation relies on
ctrl->cntlid, and this value is assigned (from id_ctrl value) after the
call for nvme_init_subsystem() in nvme_init_identify() for non-fabrics
scenario. That leads to ctrl->cntlid always being 0 in case we have a
physical set of controllers in the same subsystem.
This patch fixes that by loading the discovered cntlid id_ctrl value into
ctrl->cntlid before the subsystem initialization, only for the non-fabrics
case. The patch was tested with emulated nvme devices (qemu) having two
controllers in a single subsystem. Without the patch, we couldn't make
it work failing in the duplicate check; when running with the patch, we
could see the subsystem holding both controllers.
For the fabrics case we see ctrl->cntlid has a more intricate relation
with the admin connect, so we didn't change that.
Anton Eidelman [Mon, 12 Aug 2019 20:00:36 +0000 (23:00 +0300)]
nvme-multipath: fix possible I/O hang when paths are updated
nvme_state_set_live() making a path available triggers requeue_work
in order to resubmit requests that ended up on requeue_list when no
paths were available.
This requeue_work may race with concurrent nvme_ns_head_make_request()
that do not observe the live path yet.
Such concurrent requests may by made by either:
- New IO submission.
- Requeue_work triggered by nvme_failover_req() or another ana_work.
A race may cause requeue_work capture the state of requeue_list before
more requests get onto the list. These requests will stay on the list
forever unless requeue_work is triggered again.
In order to prevent such race, nvme_state_set_live() should
synchronize_srcu(&head->srcu) before triggering the requeue_work and
prevent nvme_ns_head_make_request referencing an old snapshot of the
path list.
Jens Axboe [Mon, 19 Aug 2019 18:15:59 +0000 (12:15 -0600)]
io_uring: fix potential hang with polled IO
If a request issue ends up being punted to async context to avoid
blocking, we can get into a situation where the original application
enters the poll loop for that very request before it has been issued.
This should not be an issue, except that the polling will hold the
io_uring uring_ctx mutex for the duration of the poll. When the async
worker has actually issued the request, it needs to acquire this mutex
to add the request to the poll issued list. Since the application
polling is already holding this mutex, the workqueue sleeps on the
mutex forever, and the application thus never gets a chance to poll for
the very request it was interested in.
Fix this by ensuring that the polling drops the uring_ctx occasionally
if it's not making any progress.
Dexuan Cui [Tue, 7 May 2019 07:46:55 +0000 (07:46 +0000)]
Drivers: hv: vmbus: Fix virt_to_hvpfn() for X86_PAE
In the case of X86_PAE, unsigned long is u32, but the physical address type
should be u64. Due to the bug here, the netvsc driver can not load
successfully, and sometimes the VM can panic due to memory corruption (the
hypervisor writes data to the wrong location).
Vitaly Kuznetsov [Mon, 19 Aug 2019 14:44:09 +0000 (16:44 +0200)]
Tools: hv: kvp: eliminate 'may be used uninitialized' warning
When building hv_kvp_daemon GCC-8.3 complains:
hv_kvp_daemon.c: In function ‘kvp_get_ip_info.constprop’:
hv_kvp_daemon.c:812:30: warning: ‘ip_buffer’ may be used uninitialized in this function [-Wmaybe-uninitialized]
struct hv_kvp_ipaddr_value *ip_buffer;
this seems to be a false positive: we only use ip_buffer when
op == KVP_OP_GET_IP_INFO and it is only unset when op == KVP_OP_ENUMERATE.
Silence the warning by initializing ip_buffer to NULL.
Dexuan Cui [Tue, 20 Aug 2019 03:06:40 +0000 (03:06 +0000)]
Drivers: hv: vmbus: Remove the unused "tsc_page" from struct hv_context
This field is no longer used after the commit 63ed4e0c67df ("Drivers: hv: vmbus: Consolidate all Hyper-V specific clocksource code")
, because it's replaced by the global variable
"struct ms_hyperv_tsc_page *tsc_pg;" (now, the variable is in
drivers/clocksource/hyperv_timer.c).
Fixes: 63ed4e0c67df ("Drivers: hv: vmbus: Consolidate all Hyper-V specific clocksource code") Signed-off-by: Dexuan Cui <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Nishka Dasgupta [Mon, 19 Aug 2019 07:51:26 +0000 (13:21 +0530)]
auxdisplay: ht16k33: Make ht16k33_fb_fix and ht16k33_fb_var constant
The static structures ht16k33_fb_fix and ht16k33_fb_var, of types
fb_fix_screeninfo and fb_var_screeninfo respectively, are not used
except to be copied into other variables. Hence make both of them
constant to prevent unintended modification.
Issue found with
Coccinelle.
arm: select the dma-noncoherent symbols for all swiotlb builds
We need to provide the arch hooks for non-coherent dma-direct
and swiotlb for all swiotlb builds, not just when LPAS is enabled.
Without that the Xen build that selects SWIOTLB indirectly through
SWIOTLB_XEN fails to build.
Fixes: ad3c7b18c5b3 ("arm: use swiotlb for bounce buffering on LPAE configs") Reported-by: Stefan Wahren <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]> Tested-by: Stefan Wahren <[email protected]>
James Smart [Fri, 16 Aug 2019 02:36:49 +0000 (19:36 -0700)]
scsi: lpfc: Mitigate high memory pre-allocation by SCSI-MQ
When SCSI-MQ is enabled, the SCSI-MQ layers will do pre-allocation of MQ
resources based on shost values set by the driver. In newer cases of the
driver, which attempts to set nr_hw_queues to the cpu count, the
multipliers become excessive, with a single shost having SCSI-MQ
pre-allocation reaching into the multiple GBytes range. NPIV, which
creates additional shosts, only multiply this overhead. On lower-memory
systems, this can exhaust system memory very quickly, resulting in a system
crash or failures in the driver or elsewhere due to low memory conditions.
After testing several scenarios, the situation can be mitigated by limiting
the value set in shost->nr_hw_queues to 4. Although the shost values were
changed, the driver still had per-cpu hardware queues of its own that
allowed parallelization per-cpu. Testing revealed that even with the
smallish number for nr_hw_queues for SCSI-MQ, performance levels remained
near maximum with the within-driver affiinitization.
A module parameter was created to allow the value set for the nr_hw_queues
to be tunable.
Linus Torvalds [Mon, 19 Aug 2019 23:28:25 +0000 (16:28 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A couple fixes to the core framework logic that finds clk parents, a
handful of samsung clk driver fixes for audio and display clks, and a
small fix for the Stratix10 SoC driver that was checking the wrong
register for validity"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Fix potential NULL dereference in clk_fetch_parent_index()
clk: Fix falling back to legacy parent string matching
clk: socfpga: stratix10: fix rate caclulationg for cnt_clks
clk: samsung: exynos542x: Move MSCL subsystem clocks to its sub-CMU
clk: samsung: exynos5800: Move MAU subsystem clocks to MAU sub-CMU
clk: samsung: Change signature of exynos5_subcmus_init() function
Linus Torvalds [Mon, 19 Aug 2019 23:17:59 +0000 (16:17 -0700)]
Merge branch 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull kernel thread signal handling fix from Eric Biederman:
"I overlooked the fact that kernel threads are created with all signals
set to SIG_IGN, and accidentally caused a regression in cifs and drbd
when replacing force_sig with send_sig.
This is my fix for that regression. I add a new function
allow_kernel_signal which allows kernel threads to receive signals
sent from the kernel, but continues to ignore all signals sent from
userspace. This ensures the user space interface for cifs and drbd
remain the same.
These kernel threads depend on blocking networking calls which block
until something is received or a signal is pending. Making receiving
of signals somewhat necessary for these kernel threads.
Perhaps someday we can cleanup those interfaces and remove
allow_kernel_signal. If not allow_kernel_signal is pretty trivial and
clearly documents what is going on so I don't think we will mind
carrying it"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Allow cifs and drbd to receive their terminating signals
Michael Kelley [Thu, 1 Aug 2019 23:53:53 +0000 (23:53 +0000)]
genirq: Properly pair kobject_del() with kobject_add()
If alloc_descs() fails before irq_sysfs_init() has run, free_desc() in the
cleanup path will call kobject_del() even though the kobject has not been
added with kobject_add().
Fix this by making the call to kobject_del() conditional on whether
irq_sysfs_init() has run.
This problem surfaced because commit aa30f47cf666 ("kobject: Add support
for default attribute groups to kobj_type") makes kobject_del() stricter
about pairing with kobject_add(). If the pairing is incorrrect, a WARNING
and backtrace occur in sysfs_remove_group() because there is no parent.
[ tglx: Add a comment to the code and make it work with CONFIG_SYSFS=n ]
Tom Lendacky [Mon, 19 Aug 2019 15:52:35 +0000 (15:52 +0000)]
x86/CPU/AMD: Clear RDRAND CPUID bit on AMD family 15h/16h
There have been reports of RDRAND issues after resuming from suspend on
some AMD family 15h and family 16h systems. This issue stems from a BIOS
not performing the proper steps during resume to ensure RDRAND continues
to function properly.
RDRAND support is indicated by CPUID Fn00000001_ECX[30]. This bit can be
reset by clearing MSR C001_1004[62]. Any software that checks for RDRAND
support using CPUID, including the kernel, will believe that RDRAND is
not supported.
Update the CPU initialization to clear the RDRAND CPUID bit for any family
15h and 16h processor that supports RDRAND. If it is known that the family
15h or family 16h system does not have an RDRAND resume issue or that the
system will not be placed in suspend, the "rdrand=force" kernel parameter
can be used to stop the clearing of the RDRAND CPUID bit.
Additionally, update the suspend and resume path to save and restore the
MSR C001_1004 value to ensure that the RDRAND CPUID setting remains in
place after resuming from suspend.
Note, that clearing the RDRAND CPUID bit does not prevent a processor
that normally supports the RDRAND instruction from executing it. So any
code that determined the support based on family and model won't #UD.
1) Fix jmp to 1st instruction in x64 JIT, from Alexei Starovoitov.
2) Severl kTLS fixes in mlx5 driver, from Tariq Toukan.
3) Fix severe performance regression due to lack of SKB coalescing of
fragments during local delivery, from Guillaume Nault.
4) Error path memory leak in sch_taprio, from Ivan Khoronzhuk.
5) Fix batched events in skbedit packet action, from Roman Mashak.
6) Propagate VLAN TX offload to hw_enc_features in bond and team
drivers, from Yue Haibing.
7) RXRPC local endpoint refcounting fix and read after free in
rxrpc_queue_local(), from David Howells.
8) Fix endian bug in ibmveth multicast list handling, from Thomas
Falcon.
9) Oops, make nlmsg_parse() wrap around the correct function,
__nlmsg_parse not __nla_parse(). Fix from David Ahern.
10) Memleak in sctp_scend_reset_streams(), fro Zheng Bin.
11) Fix memory leak in cxgb4, from Wenwen Wang.
12) Yet another race in AF_PACKET, from Eric Dumazet.
13) Fix false detection of retransmit failures in tipc, from Tuong
Lien.
14) Use after free in ravb_tstamp_skb, from Tho Vu.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
ravb: Fix use-after-free ravb_tstamp_skb
netfilter: nf_tables: map basechain priority to hardware priority
net: sched: use major priority number as hardware priority
wimax/i2400m: fix a memory leak bug
net: cavium: fix driver name
ibmvnic: Unmap DMA address of TX descriptor buffers after use
bnxt_en: Fix to include flow direction in L2 key
bnxt_en: Use correct src_fid to determine direction of the flow
bnxt_en: Suppress HWRM errors for HWRM_NVM_GET_VARIABLE command
bnxt_en: Fix handling FRAG_ERR when NVM_INSTALL_UPDATE cmd fails
bnxt_en: Improve RX doorbell sequence.
bnxt_en: Fix VNIC clearing logic for 57500 chips.
net: kalmia: fix memory leaks
cx82310_eth: fix a memory leak bug
bnx2x: Fix VF's VLAN reconfiguration in reload.
Bluetooth: Add debug setting for changing minimum encryption key size
tipc: fix false detection of retransmit failures
lan78xx: Fix memory leaks
MAINTAINERS: r8169: Update path to the driver
MAINTAINERS: PHY LIBRARY: Update files in the record
...
David Howells [Mon, 19 Aug 2019 15:02:01 +0000 (16:02 +0100)]
keys: Fix description size
The maximum key description size is 4095. Commit f771fde82051 ("keys:
Simplify key description management") inadvertantly reduced that to 255
and made sizes between 256 and 4095 work weirdly, and any size whereby
size & 255 == 0 would cause an assertion in __key_link_begin() at the
following line:
BUG_ON(index_key->desc_len == 0);
This can be fixed by simply increasing the size of desc_len in struct
keyring_index_key to a u16.
Note the argument length test in keyutils only checked empty
descriptions and descriptions with a size around the limit (ie. 4095)
and not for all the values in between, so it missed this. This has been
addressed and
keyctl add user "aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa" a @s
It breaks logic in find_trampoline_placement(): bios_start lands on the
end of the first 4k page and trampoline start gets placed below 0.
Detect underflow and don't touch bios_start for such cases. It makes
kernel ignore E820 table on machines that doesn't have two usable pages
below BIOS_START_MAX.
Jason Gerecke [Wed, 7 Aug 2019 21:11:55 +0000 (14:11 -0700)]
HID: wacom: Correct distance scale for 2nd-gen Intuos devices
Distance values reported by 2nd-gen Intuos tablets are on an inverted
scale (0 == far, 63 == near). We need to change them over to a normal
scale before reporting to userspace or else userspace drivers and
applications can get confused.
Ref: https://github.com/linuxwacom/input-wacom/issues/98 Fixes: eda01dab53 ("HID: wacom: Add four new Intuos devices") Signed-off-by: Jason Gerecke <[email protected]> Cc: <[email protected]> # v4.4+ Signed-off-by: Jiri Kosina <[email protected]>
signal: Allow cifs and drbd to receive their terminating signals
My recent to change to only use force_sig for a synchronous events
wound up breaking signal reception cifs and drbd. I had overlooked
the fact that by default kthreads start out with all signals set to
SIG_IGN. So a change I thought was safe turned out to have made it
impossible for those kernel thread to catch their signals.
Reverting the work on force_sig is a bad idea because what the code
was doing was very much a misuse of force_sig. As the way force_sig
ultimately allowed the signal to happen was to change the signal
handler to SIG_DFL. Which after the first signal will allow userspace
to send signals to these kernel threads. At least for
wake_ack_receiver in drbd that does not appear actively wrong.
So correct this problem by adding allow_kernel_signal that will allow
signals whose siginfo reports they were sent by the kernel through,
but will not allow userspace generated signals, and update cifs and
drbd to call allow_kernel_signal in an appropriate place so that their
thread can receive this signal.
Fixing things this way ensures that userspace won't be able to send
signals and cause problems, that it is clear which signals the
threads are expecting to receive, and it guarantees that nothing
else in the system will be affected.
This change was partly inspired by similar cifs and drbd patches that
added allow_signal.
Reported-by: ronnie sahlberg <[email protected]> Reported-by: Christoph Böhmwalder <[email protected]> Tested-by: Christoph Böhmwalder <[email protected]> Cc: Steve French <[email protected]> Cc: Philipp Reisner <[email protected]> Cc: David Laight <[email protected]> Fixes: 247bc9470b1e ("cifs: fix rmmod regression in cifs.ko caused by force_sig changes") Fixes: 72abe3bcf091 ("signal/cifs: Fix cifs_put_tcp_session to call send_sig instead of force_sig") Fixes: fee109901f39 ("signal/drbd: Use send_sig not force_sig") Fixes: 3cf5d076fb4d ("signal: Remove task parameter from force_sig") Signed-off-by: "Eric W. Biederman" <[email protected]>
Thomas Gleixner [Fri, 9 Aug 2019 12:54:07 +0000 (14:54 +0200)]
x86/apic: Handle missing global clockevent gracefully
Some newer machines do not advertise legacy timers. The kernel can handle
that situation if the TSC and the CPU frequency are enumerated by CPUID or
MSRs and the CPU supports TSC deadline timer. If the CPU does not support
TSC deadline timer the local APIC timer frequency has to be known as well.
Some Ryzens machines do not advertize legacy timers, but there is no
reliable way to determine the bus frequency which feeds the local APIC
timer when the machine allows overclocking of that frequency.
As there is no legacy timer the local APIC timer calibration crashes due to
a NULL pointer dereference when accessing the not installed global clock
event device.
Switch the calibration loop to a non interrupt based one, which polls
either TSC (if frequency is known) or jiffies. The latter requires a global
clockevent. As the machines which do not have a global clockevent installed
have a known TSC frequency this is a non issue. For older machines where
TSC frequency is not known, there is no known case where the legacy timers
do not exist as that would have been reported long ago.
sched/core: Schedule new worker even if PI-blocked
If a task is PI-blocked (blocking on sleeping spinlock) then we don't want to
schedule a new kworker if we schedule out due to lock contention because !RT
does not do that as well. A spinning spinlock disables preemption and a worker
does not schedule out on lock contention (but spin).
On RT the RW-semaphore implementation uses an rtmutex so
tsk_is_pi_blocked() will return true if a task blocks on it. In this case we
will now start a new worker which may deadlock if one worker is waiting on
progress from another worker. Since a RW-semaphore starts a new worker on !RT,
we should do the same on RT.
XFS is able to trigger this deadlock.
Allow to schedule new worker if the current worker is PI-blocked.
Darrick J. Wong [Thu, 15 Aug 2019 00:38:09 +0000 (17:38 -0700)]
xfs: fix reflink source file racing with directio writes
While trawling through the dedupe file comparison code trying to fix
page deadlocking problems, Dave Chinner noticed that the reflink code
only takes shared IOLOCK/MMAPLOCKs on the source file. Because
page_mkwrite and directio writes do not take the EXCL versions of those
locks, this means that reflink can race with writer processes.
For pure remapping this can lead to undefined behavior and file
corruption; for dedupe this means that we cannot be sure that the
contents are identical when we decide to go ahead with the remapping.
drm/mediatek: mtk_drm_drv.c: Add of_node_put() before goto
Each iteration of for_each_child_of_node puts the previous
node, but in the case of a goto from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
goto in two places.
Issue found with Coccinelle.
Fixes: 119f5173628a (drm/mediatek: Add DRM Driver for Mediatek SoC MT8173) Signed-off-by: Nishka Dasgupta <[email protected]> Signed-off-by: CK Hu <[email protected]>
Tho Vu [Fri, 16 Aug 2019 15:17:02 +0000 (17:17 +0200)]
ravb: Fix use-after-free ravb_tstamp_skb
When a Tx timestamp is requested, a pointer to the skb is stored in the
ravb_tstamp_skb struct. This was done without an skb_get. There exists
the possibility that the skb could be freed by ravb_tx_free (when
ravb_tx_free is called from ravb_start_xmit) before the timestamp was
processed, leading to a use-after-free bug.
Use skb_get when filling a ravb_tstamp_skb struct, and add appropriate
frees/consumes when a ravb_tstamp_skb struct is freed.
This patchset contains two updates for the flow_offload users:
1) Pass the major tc priority to drivers so they do not have to
lshift it. This is a preparation patch for the fix coming in
patch #2.
2) Set the hardware priority from the netfilter basechain priority,
some drivers break when using the existing hardware priority
number that is set to zero.
v5: fix patch 2/2 to address a clang warning and to simplify
the priority mapping.
====================
netfilter: nf_tables: map basechain priority to hardware priority
This patch adds initial support for offloading basechains using the
priority range from 1 to 65535. This is restricting the netfilter
priority range to 16-bit integer since this is what most drivers assume
so far from tc. It should be possible to extend this range of supported
priorities later on once drivers are updated to support for 32-bit
integer priorities.
net: sched: use major priority number as hardware priority
tc transparently maps the software priority number to hardware. Update
it to pass the major priority which is what most drivers expect. Update
drivers too so they do not need to lshift the priority field of the
flow_cls_common_offload object. The stmmac driver is an exception, since
this code assumes the tc software priority is fine, therefore, lshift it
just to be conservative.
Wenwen Wang [Thu, 15 Aug 2019 20:29:51 +0000 (15:29 -0500)]
wimax/i2400m: fix a memory leak bug
In i2400m_barker_db_init(), 'options_orig' is allocated through kstrdup()
to hold the original command line options. Then, the options are parsed.
However, if an error occurs during the parsing process, 'options_orig' is
not deallocated, leading to a memory leak bug. To fix this issue, free
'options_orig' before returning the error.
The driver name gets exposed in sysfs under /sys/bus/pci/drivers
so it should look like other devices. Change it to be common
format (instead of "Cavium PTP").
This is a trivial fix that was observed by accident because
Debian kernels were building this driver into kernel (bug).
Thomas Falcon [Wed, 14 Aug 2019 19:57:05 +0000 (14:57 -0500)]
ibmvnic: Unmap DMA address of TX descriptor buffers after use
There's no need to wait until a completion is received to unmap
TX descriptor buffers that have been passed to the hypervisor.
Instead unmap it when the hypervisor call has completed. This patch
avoids the possibility that a buffer will not be unmapped because
a TX completion is lost or mishandled.
David S. Miller [Sun, 18 Aug 2019 20:05:01 +0000 (13:05 -0700)]
Merge branch 'bnxt_en-Bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
2 Bug fixes related to 57500 shutdown sequence and doorbell sequence,
2 TC Flower bug fixes related to the setting of the flow direction,
1 NVRAM update bug fix, and a minor fix to suppress an unnecessary
error message. Please queue for -stable as well. Thanks.
====================
Somnath Kotur [Sat, 17 Aug 2019 21:04:52 +0000 (17:04 -0400)]
bnxt_en: Fix to include flow direction in L2 key
FW expects the driver to provide unique flow reference handles
for Tx or Rx flows. When a Tx flow and an Rx flow end up sharing
a reference handle, flow offload does not seem to work.
This could happen in the case of 2 flows having their L2 fields
wildcarded but in different direction.
Fix to incorporate the flow direction as part of the L2 key
v2: Move the dir field to the end of the bnxt_tc_l2_key struct to
fix the warning reported by kbuild test robot <[email protected]>.
There is existing code that initializes the structure using
nested initializer and will warn with the new u8 field added to
the beginning. The structure also packs nicer when this new u8 is
added to the end of the structure [MChan].
Fixes: abd43a13525d ("bnxt_en: Support for 64-bit flow handle.") Signed-off-by: Somnath Kotur <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Venkat Duvvuru [Sat, 17 Aug 2019 21:04:51 +0000 (17:04 -0400)]
bnxt_en: Use correct src_fid to determine direction of the flow
Direction of the flow is determined using src_fid. For an RX flow,
src_fid is PF's fid and for TX flow, src_fid is VF's fid. Direction
of the flow must be specified, when getting statistics for that flow.
Currently, for DECAP flow, direction is determined incorrectly, i.e.,
direction is initialized as TX for DECAP flow, instead of RX. Because
of which, stats are not reported for this DECAP flow, though it is
offloaded and there is traffic for that flow, resulting in flow age out.
This patch fixes the problem by determining the DECAP flow's direction
using correct fid. Set the flow direction in all cases for consistency
even if 64-bit flow handle is not used.
Fixes: abd43a13525d ("bnxt_en: Support for 64-bit flow handle.") Signed-off-by: Venkat Duvvuru <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vasundhara Volam [Sat, 17 Aug 2019 21:04:50 +0000 (17:04 -0400)]
bnxt_en: Suppress HWRM errors for HWRM_NVM_GET_VARIABLE command
For newly added NVM parameters, older firmware may not have the support.
Suppress the error message to avoid the unncessary error message which is
triggered when devlink calls the driver during initialization.
Fixes: 782a624d00fa ("bnxt_en: Add bnxt_en initial params table and register it.") Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vasundhara Volam [Sat, 17 Aug 2019 21:04:49 +0000 (17:04 -0400)]
bnxt_en: Fix handling FRAG_ERR when NVM_INSTALL_UPDATE cmd fails
If FW returns FRAG_ERR in response error code, driver is resending the
command only when HWRM command returns success. Fix the code to resend
NVM_INSTALL_UPDATE command with DEFRAG install flags, if FW returns
FRAG_ERR in its response error code.
Fixes: cb4d1d626145 ("bnxt_en: Retry failed NVM_INSTALL_UPDATE with defragmentation flag enabled.") Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Michael Chan [Sat, 17 Aug 2019 21:04:48 +0000 (17:04 -0400)]
bnxt_en: Improve RX doorbell sequence.
When both RX buffers and RX aggregation buffers have to be
replenished at the end of NAPI, post the RX aggregation buffers first
before RX buffers. Otherwise, we may run into a situation where
there are only RX buffers without RX aggregation buffers for a split
second. This will cause the hardware to abort the RX packet and
report buffer errors, which will cause unnecessary cleanup by the
driver.
Ringing the Aggregation ring doorbell first before the RX ring doorbell
will prevent some of these buffer errors. Use the same sequence during
ring initialization as well.
Fixes: 697197e5a173 ("bnxt_en: Re-structure doorbells.") Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Michael Chan [Sat, 17 Aug 2019 21:04:47 +0000 (17:04 -0400)]
bnxt_en: Fix VNIC clearing logic for 57500 chips.
During device shutdown, the VNIC clearing sequence needs to be modified
to free the VNIC first before freeing the RSS contexts. The current
code is doing the reverse and we can get mis-directed RX completions
to CP ring ID 0 when the RSS contexts are freed and zeroed. The clearing
of RSS contexts is not required with the new sequence.
Refactor the VNIC clearing logic into a new function bnxt_clear_vnic()
and do the chip specific VNIC clearing sequence.
Fixes: 7b3af4f75b81 ("bnxt_en: Add RSS support for 57500 chips.") Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Wenwen Wang [Wed, 14 Aug 2019 18:56:43 +0000 (13:56 -0500)]
net: kalmia: fix memory leaks
In kalmia_init_and_get_ethernet_addr(), 'usb_buf' is allocated through
kmalloc(). In the following execution, if the 'status' returned by
kalmia_send_init_packet() is not 0, 'usb_buf' is not deallocated, leading
to memory leaks. To fix this issue, add the 'out' label to free 'usb_buf'.
Wenwen Wang [Wed, 14 Aug 2019 18:03:38 +0000 (13:03 -0500)]
cx82310_eth: fix a memory leak bug
In cx82310_bind(), 'dev->partial_data' is allocated through kmalloc().
Then, the execution waits for the firmware to become ready. If the firmware
is not ready in time, the execution is terminated. However, the allocated
'dev->partial_data' is not deallocated on this path, leading to a memory
leak bug. To fix this issue, free 'dev->partial_data' before returning the
error.
Manish Chopra [Sun, 18 Aug 2019 14:25:48 +0000 (07:25 -0700)]
bnx2x: Fix VF's VLAN reconfiguration in reload.
Commit 04f05230c5c13 ("bnx2x: Remove configured vlans as
part of unload sequence."), introduced a regression in driver
that as a part of VF's reload flow, VLANs created on the VF
doesn't get re-configured in hardware as vlan metadata/info
was not getting cleared for the VFs which causes vlan PING to stop.
This patch clears the vlan metadata/info so that VLANs gets
re-configured back in the hardware in VF's reload flow and
PING/traffic continues for VLANs created over the VFs.
Fixes: 04f05230c5c13 ("bnx2x: Remove configured vlans as part of unload sequence.") Signed-off-by: Manish Chopra <[email protected]> Signed-off-by: Sudarsana Kalluru <[email protected]> Signed-off-by: Shahed Shaikh <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Sun, 18 Aug 2019 16:51:48 +0000 (09:51 -0700)]
Merge tag 'for-5.3-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Two fixes that popped up during testing:
- fix for sysfs-related code that adds/removes block groups, warnings
appear during several fstests in connection with sysfs updates in
5.3, the fix essentially replaces a workaround with scope NOFS and
applies to 5.2-based branch too
- add sanity check of trim range"
* tag 'for-5.3-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: trim: Check the range passed into to prevent overflow
Btrfs: fix sysfs warning and missing raid sysfs directories
Linus Torvalds [Sun, 18 Aug 2019 16:45:42 +0000 (09:45 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the inconsistent error handling in the umwait init code
- Rework the boot param zeroing so gcc9 stops complaining about out
of bound memset. The resulting source code is actually more sane to
read than the smart solution we had
- Maintainers update so Tony gets involved when Intel models are
added
- Some more fallthrough fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Save fields explicitly, zero out everything else
MAINTAINERS, x86/CPU: Tony Luck will maintain asm/intel-family.h
x86/fpu/math-emu: Address fallthrough warnings
x86/apic/32: Fix yet another implicit fallthrough warning
x86/umwait: Fix error handling in umwait_init()
Linus Torvalds [Sun, 18 Aug 2019 16:36:51 +0000 (09:36 -0700)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Thomas Gleixner:
"A single fix for a EFI mixed mode regression caused by recent rework
which did not take the firmware bitwidth into account"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi-stub: Fix get_efi_config_table on mixed-mode setups
Linus Torvalds [Sun, 18 Aug 2019 16:26:16 +0000 (09:26 -0700)]
Merge tag 'spdx-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX fixes from Greg KH:
"Here are four small SPDX fixes for 5.3-rc5.
A few style fixes for some SPDX comments, added an SPDX tag for one
file, and fix up some GPL boilerplate for another file.
All of these have been in linux-next for a few weeks with no reported
issues (they are comment changes only, so that's to be expected...)"
* tag 'spdx-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
i2c: stm32: Use the correct style for SPDX License Identifier
intel_th: Use the correct style for SPDX License Identifier
coccinelle: api/atomic_as_refcounter: add SPDX License Identifier
kernel/configs: Replace GPL boilerplate code with SPDX identifier
Linus Torvalds [Sun, 18 Aug 2019 16:17:41 +0000 (09:17 -0700)]
Merge tag 'char-misc-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for 5.3-rc5.
These are two different subsystems needing some fixes, the habanalabs
driver which is has some more big endian fixes for problems found. The
other are some small soundwire fixes, including some Kconfig
dependencies needed to resolve reported build errors.
All of these have been in linux-next this week with no reported
issues"
* tag 'char-misc-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: xilinx-sdfec: fix dependency and build error
habanalabs: fix device IRQ unmasking for BE host
habanalabs: fix endianness handling for internal QMAN submission
habanalabs: fix completion queue handling when host is BE
habanalabs: fix endianness handling for packets from user
habanalabs: fix DRAM usage accounting on context tear down
habanalabs: Avoid double free in error flow
soundwire: fix regmap dependencies and align with other serial links
soundwire: cadence_master: fix definitions for INTSTAT0/1
soundwire: cadence_master: fix register definition for SLAVE_STATE
Linus Torvalds [Sun, 18 Aug 2019 16:14:56 +0000 (09:14 -0700)]
Merge tag 'staging-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are four small staging and iio driver fixes for 5.3-rc5
Two are for the dt3000 comedi driver for some reported problems found
in that codebase, and two are some small iio fixes.
All of these have been in linux-next this week with no reported
issues"
* tag 'staging-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: dt3000: Fix rounding up of timer divisor
staging: comedi: dt3000: Fix signed integer overflow 'divider * base'
iio: adc: max9611: Fix temperature reading in probe
iio: frequency: adf4371: Fix output frequency setting
Linus Torvalds [Sun, 18 Aug 2019 16:11:29 +0000 (09:11 -0700)]
Merge tag 'usb-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are number of small USB fixes for 5.3-rc5.
Syzbot has been on a tear recently now that it has some good USB
debugging hooks integrated, so there's a number of fixes in here found
by those tools for some _very_ old bugs. Also a handful of gadget
driver fixes for reported issues, some hopefully-final dma fixes for
host controller drivers, and some new USB serial gadget driver ids.
All of these have been in linux-next this week with no reported issues
(the usb-serial ones were in linux-next in its own branch, but merged
into mine on Friday)"
* tag 'usb-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: add a hcd_uses_dma helper
usb: don't create dma pools for HCDs with a localmem_pool
usb: chipidea: imx: fix EPROBE_DEFER support during driver probe
usb: host: fotg2: restart hcd after port reset
USB: CDC: fix sanity checks in CDC union parser
usb: cdc-acm: make sure a refcount is taken early enough
USB: serial: option: add the BroadMobi BM818 card
USB: serial: option: Add Motorola modem UARTs
USB: core: Fix races in character device registration and deregistraion
usb: gadget: mass_storage: Fix races between fsg_disable and fsg_set_alt
usb: gadget: composite: Clear "suspended" on reset/disconnect
usb: gadget: udc: renesas_usb3: Fix sysfs interface of "role"
USB: serial: option: add D-Link DWM-222 device ID
USB: serial: option: Add support for ZTE MF871A
Linus Torvalds [Sun, 18 Aug 2019 02:39:54 +0000 (19:39 -0700)]
Merge tag 'for-linus-2019-08-17' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into this series. This contains:
- Revert of the REQ_NOWAIT_INLINE and associated dio changes. There
were still corner cases there, and even though I had a solution for
it, it's too involved for this stage. (me)
- Set of NVMe fixes (via Sagi)
- io_uring fix for fixed buffers (Anthony)
- io_uring defer issue fix (Jackie)
- Regression fix for queue sync at exit time (zhengbin)
- xen blk-back memory leak fix (Wenwen)"
* tag 'for-linus-2019-08-17' of git://git.kernel.dk/linux-block:
io_uring: fix an issue when IOSQE_IO_LINK is inserted into defer list
block: remove REQ_NOWAIT_INLINE
io_uring: fix manual setup of iov_iter for fixed buffers
xen/blkback: fix memory leaks
blk-mq: move cancel of requeue_work to the front of blk_exit_queue
nvme-pci: Fix async probe remove race
nvme: fix controller removal race with scan work
nvme-rdma: fix possible use-after-free in connect error flow
nvme: fix a possible deadlock when passthru commands sent to a multipath device
nvme-core: Fix extra device_put() call on error path
nvmet-file: fix nvmet_file_flush() always returning an error
nvmet-loop: Flush nvme_delete_wq when removing the port
nvmet: Fix use-after-free bug when a port is removed
nvme-multipath: revalidate nvme_ns_head gendisk in nvme_validate_ns
Linus Torvalds [Sun, 18 Aug 2019 02:31:30 +0000 (19:31 -0700)]
Merge tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V fixes from Sasha Levin:
- A few fixes for the userspace hyper-v tools from Adrian Vladu.
- A fix for the hyper-v MAINTAINERs entry from Lan Tianyu.
- Fix for SPDX license identifier in the userspace tools from Nishad
Kamdar.
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
MAINTAINERS: Fix Hyperv vIOMMU driver file name
tools: hv: Use the correct style for SPDX License Identifier
tools: hv: fix typos in toolchain
tools: hv: fix KVP and VSS daemons exit code
tools: hv: fixed Python pep8/flake8 warnings for lsvmbus
David S. Miller [Sat, 17 Aug 2019 19:37:47 +0000 (12:37 -0700)]
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2019-08-17
Here's a set of Bluetooth fixes for the 5.3-rc series:
- Multiple fixes for Qualcomm (btqca & hci_qca) drivers
- Minimum encryption key size debugfs setting (this is required for
Bluetooth Qualification)
- Fix hidp_send_message() to have a meaningful return value
====================
tools: hv: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style
in the trace header file related to Microsoft Hyper-V
client drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
Adrian Vladu [Mon, 6 May 2019 17:27:37 +0000 (17:27 +0000)]
tools: hv: fixed Python pep8/flake8 warnings for lsvmbus
Fixed pep8/flake8 python style code for lsvmbus tool.
The TAB indentation was on purpose ignored (pep8 rule W191) to make
sure the code is complying with the Linux code guideline.
The following command doe not show any warnings now:
pep8 --ignore=W191 lsvmbus
flake8 --ignore=W191 lsvmbus
Linus Torvalds [Sat, 17 Aug 2019 17:44:50 +0000 (10:44 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has one revert because of a regression, two fixes for tiny race
windows (which we were not able to trigger), a MAINTAINERS addition,
and a SPDX fix"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32: Use the correct style for SPDX License Identifier
i2c: emev2: avoid race when unregistering slave client
i2c: rcar: avoid race when unregistering slave client
MAINTAINERS: i2c-imx: take over maintainership
Revert "i2c: imx: improve the error handling in i2c_imx_dma_request()"
Linus Torvalds [Sat, 17 Aug 2019 17:36:47 +0000 (10:36 -0700)]
Merge tag 'riscv/for-v5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
- Two patches to fix significant bugs in floating point register
context handling
- A minor fix in RISC-V flush_tlb_page(), to supply a valid end address
to flush_tlb_range()
- Two minor defconfig additions: to build the virtio hwrng driver by
default (for QEMU targets), and to partially synchronize the 32-bit
defconfig with the 64-bit defconfig
* tag 'riscv/for-v5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Make __fstate_clean() work correctly.
riscv: Correct the initialized flow of FP register
riscv: defconfig: Update the defconfig
riscv: rv32_defconfig: Update the defconfig
riscv: fix flush_tlb_range() end address for flush_tlb_page()
Bluetooth: Add debug setting for changing minimum encryption key size
For testing and qualification purposes it is useful to allow changing
the minimum encryption key size value that the host stack is going to
enforce. This adds a new debugfs setting min_encrypt_key_size to achieve
this functionality.
Darrick J. Wong [Sun, 11 Aug 2019 22:52:25 +0000 (15:52 -0700)]
vfs: fix page locking deadlocks when deduping files
When dedupe wants to use the page cache to compare parts of two files
for dedupe, we must be very careful to handle locking correctly. The
current code doesn't do this. It must lock and unlock the page only
once if the two pages are the same, since the overlapping range check
doesn't catch this when blocksize < pagesize. If the pages are distinct
but from the same file, we must observe page locking order and lock them
in order of increasing offset to avoid clashing with writeback locking.
Fixes: 876bec6f9bbfcb3 ("vfs: refactor clone/dedupe_file_range common functions") Signed-off-by: Darrick J. Wong <[email protected]> Reviewed-by: Bill O'Donnell <[email protected]> Reviewed-by: Matthew Wilcox (Oracle) <[email protected]>
projects / linux.git / log