Huang Rui [Mon, 12 Dec 2016 12:28:26 +0000 (07:28 -0500)]
iommu/amd: Fix the left value check of cmd buffer
The generic command buffer entry is 128 bits (16 bytes), so the offset
of tail and head pointer should be 16 bytes aligned and increased with
0x10 per command.
When cmd buf is full, head = (tail + 0x10) % CMD_BUFFER_SIZE.
So when left space of cmd buf should be able to store only two
command, we should be issued one COMPLETE_WAIT additionally to wait
all older commands completed. Then the left space should be increased
after IOMMU fetching from cmd buf.
So left check value should be left <= 0x20 (two commands).
Signed-off-by: Huang Rui <[email protected]> Fixes: ac0ea6e92b222 ('x86/amd-iommu: Improve handling of full command buffer') Signed-off-by: Joerg Roedel <[email protected]>
Jacob Pan [Tue, 6 Dec 2016 18:14:23 +0000 (10:14 -0800)]
iommu/vt-d: Fix pasid table size encoding
Different encodings are used to represent supported PASID bits
and number of PASID table entries.
The current code assigns ecap_pss directly to extended context
table entry PTS which is wrong and could result in writing
non-zero bits to the reserved fields. IOMMU fault reason
11 will be reported when reserved bits are nonzero.
This patch converts ecap_pss to extend context entry pts encoding
based on VT-d spec. Chapter 9.4 as follows:
- number of PASID bits = ecap_pss + 1
- number of PASID table entries = 2^(pts + 5)
Software assigned limit of pasid_max value is also respected to
match the allocation limitation of PASID table.
Xunlei Pang [Mon, 5 Dec 2016 12:09:07 +0000 (20:09 +0800)]
iommu/vt-d: Flush old iommu caches for kdump when the device gets context mapped
We met the DMAR fault both on hpsa P420i and P421 SmartArray controllers
under kdump, it can be steadily reproduced on several different machines,
the dmesg log is like:
HP HPSA Driver (v 3.4.16-0)
hpsa 0000:02:00.0: using doorbell to reset controller
hpsa 0000:02:00.0: board ready after hard reset.
hpsa 0000:02:00.0: Waiting for controller to respond to no-op
DMAR: Setting identity map for device 0000:02:00.0 [0xe8000 - 0xe8fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xf4000 - 0xf4fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6e000 - 0xbdf6efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6f000 - 0xbdf7efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf7f000 - 0xbdf82fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf83000 - 0xbdf84fff]
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [02:00.0] fault addr fffff000 [fault reason 06] PTE Read access is not set
hpsa 0000:02:00.0: controller message 03:00 timed out
hpsa 0000:02:00.0: no-op failed; re-trying
After some debugging, we found that the fault addr is from DMA initiated at
the driver probe stage after reset(not in-flight DMA), and the corresponding
pte entry value is correct, the fault is likely due to the old iommu caches
of the in-flight DMA before it.
Thus we need to flush the old cache after context mapping is setup for the
device, where the device is supposed to finish reset at its driver probe
stage and no in-flight DMA exists hereafter.
I'm not sure if the hardware is responsible for invalidating all the related
caches allocated in the iommu hardware before, but seems not the case for hpsa,
actually many device drivers have problems in properly resetting the hardware.
Anyway flushing (again) by software in kdump kernel when the device gets context
mapped which is a quite infrequent operation does little harm.
With this patch, the problematic machine can survive the kdump tests.
Arvind Yadav [Tue, 13 Dec 2016 08:20:52 +0000 (13:50 +0530)]
video: fbdev: cobalt_lcdfb: Handle return NULL error from devm_ioremap
Here, If devm_ioremap will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Takashi Iwai [Tue, 6 Dec 2016 15:20:36 +0000 (16:20 +0100)]
ALSA: hda - Fix up GPIO for ASUS ROG Ranger
ASUS ROG Ranger VIII with ALC1150 codec requires the extra GPIO pin to
up for the front panel. Just use the existing fixup for setting up
the GPIO pins.
Johan Hovold [Tue, 3 Jan 2017 15:39:54 +0000 (16:39 +0100)]
USB: serial: mos7720: remove obsolete port initialisation
Since commit b69578df7e98 ("USB: usbserial: mos7720: add support for
parallel port on moschip 7715"), the interrupt urb is no longer
submitted at first port open and the endpoint-address initialisation at
port-probe is no longer used.
Johan Hovold [Tue, 3 Jan 2017 15:39:53 +0000 (16:39 +0100)]
USB: serial: mos7720: fix parallel probe
A static usb-serial-driver structure that is used to initialise the
interrupt URB was modified during probe depending on the currently
probed device type, something which could break a parallel probe of a
device of a different type.
Fix this up by overriding the default completion callback for MCS7715
devices in attach() instead. We may want to use two usb-serial driver
instances for the two types later.
Fixes: fb088e335d78 ("USB: serial: add support for serial port on the
moschip 7715") Cc: stable <[email protected]> Signed-off-by: Johan Hovold <[email protected]>
Johan Hovold [Tue, 3 Jan 2017 15:39:52 +0000 (16:39 +0100)]
USB: serial: mos7720: fix parport use-after-free on probe errors
Do not submit the interrupt URB until after the parport has been
successfully registered to avoid another use-after-free in the
completion handler when accessing the freed parport private data in case
of a racing completion.
Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715") Cc: stable <[email protected]> Signed-off-by: Johan Hovold <[email protected]>
Johan Hovold [Tue, 3 Jan 2017 15:39:51 +0000 (16:39 +0100)]
USB: serial: mos7720: fix use-after-free on probe errors
The interrupt URB was submitted on probe but never stopped on probe
errors. This can lead to use-after-free issues in the completion
handler when accessing the freed usb-serial struct:
Unable to handle kernel paging request at virtual address 6b6b6be7
...
[<bf052e70>] (mos7715_interrupt_callback [mos7720]) from [<c052a894>] (__usb_hcd_giveback_urb+0x80/0x140)
[<c052a894>] (__usb_hcd_giveback_urb) from [<c052a9a4>] (usb_hcd_giveback_urb+0x50/0x138)
[<c052a9a4>] (usb_hcd_giveback_urb) from [<c0550684>] (musb_giveback+0xc8/0x1cc)
Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715") Cc: stable <[email protected]> Signed-off-by: Johan Hovold <[email protected]>
Johan Hovold [Tue, 3 Jan 2017 15:39:48 +0000 (16:39 +0100)]
USB: serial: keyspan_pda: verify endpoints at probe
Check for the expected endpoints in attach() and fail loudly if not
present.
Note that failing to do this appears to be benign since da280e348866
("USB: keyspan_pda: clean up write-urb busy handling") which prevents a
NULL-pointer dereference in write() by never marking a non-existent
write-urb as free.
Johan Hovold [Tue, 3 Jan 2017 15:39:46 +0000 (16:39 +0100)]
USB: serial: io_ti: bind to interface after fw download
Bind to the interface, but do not register any ports, after having
downloaded the firmware. The device will still disconnect and
re-enumerate, but this way we avoid an error messages from being logged
as part of the process:
Johan Hovold [Tue, 3 Jan 2017 15:39:44 +0000 (16:39 +0100)]
USB: serial: io_ti: fix another NULL-deref at open
In case a device is left in "boot-mode" we must not register any port
devices in order to avoid a NULL-pointer dereference on open due to
missing endpoints. This could be used by a malicious device to trigger
an OOPS:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf0caa84>] (edge_open [io_ti]) from [<bf0b0118>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf0b0118>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf0b0da0>] (serial_open+0x48/0x6c [usbserial])
[<bf0b0da0>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
xfs: fix crash and data corruption due to removal of busy COW extents
There is a race window between write_cache_pages calling
clear_page_dirty_for_io and XFS calling set_page_writeback, in which
the mapping for an inode is tagged neither as dirty, nor as writeback.
If the COW shrinker hits in exactly that window we'll remove the delayed
COW extents and writepages trying to write it back, which in release
kernels will manifest as corruption of the bmap btree, and in debug
kernels will trip the ASSERT about now calling xfs_bmapi_write with the
COWFORK flag for holes. A complex customer load manages to hit this
window fairly reliably, probably by always having COW writeback in flight
while the cow shrinker runs.
This patch adds another check for having the I_DIRTY_PAGES flag set,
which is still set during this race window. While this fixes the problem
I'm still not overly happy about the way the COW shrinker works as it
still seems a bit fragile.
Darrick J. Wong [Wed, 4 Jan 2017 02:39:33 +0000 (18:39 -0800)]
xfs: use the actual AG length when reserving blocks
We need to use the actual AG length when making per-AG reservations,
since we could otherwise end up reserving more blocks out of the last
AG than there are actual blocks.
Jan Kara [Wed, 14 Dec 2016 13:40:05 +0000 (14:40 +0100)]
audit: Fix sleep in atomic
Audit tree code was happily adding new notification marks while holding
spinlocks. Since fsnotify_add_mark() acquires group->mark_mutex this can
lead to sleeping while holding a spinlock, deadlocks due to lock
inversion, and probably other fun. Fix the problem by acquiring
group->mark_mutex earlier.
Linus Torvalds [Tue, 3 Jan 2017 18:50:05 +0000 (10:50 -0800)]
Merge branch 'parisc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
- limit usage of processor-internal cr16 clocksource to UP systems only
- segfault info lines in syslog were too long, split those up
- drop own TIF_RESTORE_SIGMASK flag and switch to generic code
* 'parisc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Add line-break when printing segfault info
parisc: Drop TIF_RESTORE_SIGMASK and switch to generic code
parisc: Mark cr16 clocksource unstable on SMP systems
Jiandi An [Wed, 28 Dec 2016 00:47:32 +0000 (18:47 -0600)]
Xen: ARM: Zero reserved fields of xatp before making hypervisor call
Ensure all reserved fields of xatp are zero before making
hypervisor call to XEN in xen_map_device_mmio().
xenmem_add_to_physmap_one() in XEN fails the mapping request if
extra.res reserved field in xatp is not zero for XENMAPSPACE_dev_mmio
request.
Sudeep Holla [Tue, 3 Jan 2017 12:32:47 +0000 (12:32 +0000)]
drivers: psci: annotate timer on stack to silence odebug messages
When DEBUG_OBJECTS config is enabled, we get the below odebug warnings:
ODEBUG: object is on stack, but not annotated
WARNING: CPU: 3 PID: 1304 at kernel/lib/debugobjects.c:300 __debug_object_init+0x1f0/0x458
CPU: 3 PID: 1304 Comm: psci_suspend_te Tainted: G W 4.9.0-06564-gf80f3f199260 #284
task: ffffe9e1b55a1600 task.stack: ffffe9e1b51c0000
PC is at __debug_object_init+0x1f0/0x458
LR is at __debug_object_init+0x1ec/0x458
Call trace:
__debug_object_init+0x1f0/0x458
debug_object_activate+0x150/0x260
mod_timer+0xb4/0x4c0
suspend_test_thread+0x1cc/0x3c0
kthread+0x110/0x140
ret_from_fork+0x10/0x40
This patch annotates the timer on the stack using setup_timer_on_stack
function to remove the above warnings.
Felipe Balbi [Tue, 3 Jan 2017 16:28:53 +0000 (18:28 +0200)]
usb: host: xhci: handle COMP_STOP from SETUP phase too
Stop Endpoint command can come at any point and we
have no control of that. We should make sure to
handle COMP_STOP on SETUP phase as well, otherwise
urb->actual_length might be set to negative values
in some occasions such as below:
trb->length is 8 for SETUP stage (8 control request
bytes), so actual_length would be set to -4 in this
case.
While doing that, also make sure to use TRB_TYPE
field of the actual TRB instead of matching pointers
to figure out in which stage of the control transfer
we got our completion event.
OGAWA Hirofumi [Tue, 3 Jan 2017 16:28:51 +0000 (18:28 +0200)]
xhci: Fix race related to abort operation
Current abort operation has race.
xhci_handle_command_timeout()
xhci_abort_cmd_ring()
xhci_write_64(CMD_RING_ABORT)
xhci_handshake(5s)
do {
check CMD_RING_RUNNING
udelay(1)
...
COMP_CMD_ABORT event
COMP_CMD_STOP event
xhci_handle_stopped_cmd_ring()
restart cmd_ring
CMD_RING_RUNNING become 1 again
} while ()
return -ETIMEDOUT
xhci_write_64(CMD_RING_ABORT)
/* can abort random command */
To do abort operation correctly, we have to wait both of COMP_CMD_STOP
event and negation of CMD_RING_RUNNING.
But like above, while timeout handler is waiting negation of
CMD_RING_RUNNING, event handler can restart cmd_ring. So timeout
handler never be notice negation of CMD_RING_RUNNING, and retry of
CMD_RING_ABORT can abort random command (BTW, I guess retry of
CMD_RING_ABORT was workaround of this race).
To fix this race, this moves xhci_handle_stopped_cmd_ring() to
xhci_abort_cmd_ring(). And timeout handler waits COMP_CMD_STOP event.
At this point, timeout handler is owner of cmd_ring, and safely
restart cmd_ring by using xhci_handle_stopped_cmd_ring().
[FWIW, as bonus, this way would be easily extend to add CMD_RING_PAUSE
operation]
[locks edited as patch is rebased on other locking fixes -Mathias] Signed-off-by: OGAWA Hirofumi <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
OGAWA Hirofumi [Tue, 3 Jan 2017 16:28:50 +0000 (18:28 +0200)]
xhci: Use delayed_work instead of timer for command timeout
This is preparation to fix abort operation race (See "xhci: Fix race
related to abort operation"). To make timeout sleepable, use
delayed_work instead of timer.
[change a newly added pending timer fix to pending work -Mathias] Signed-off-by: OGAWA Hirofumi <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Lu Baolu [Tue, 3 Jan 2017 16:28:49 +0000 (18:28 +0200)]
usb: xhci: hold lock over xhci_abort_cmd_ring()
In command timer function, xhci_handle_command_timeout(), xhci->lock
is unlocked before call into xhci_abort_cmd_ring(). This might cause
race between the timer function and the event handler.
The xhci_abort_cmd_ring() function sets the CMD_RING_ABORT bit in the
command register and polling it until the setting takes effect. A stop
command ring event might be handled between writing the abort bit and
polling for it. The event handler will restart the command ring, which
causes the failure of polling, and we ever believed that we failed to
stop it.
As a bonus, this also fixes some issues of calling functions without
locking in xhci_handle_command_timeout().
Mathias Nyman [Tue, 3 Jan 2017 16:28:48 +0000 (18:28 +0200)]
xhci: Handle command completion and timeout race
If we get a command completion event at the same time as the command
timeout work starts on another cpu we might end up aborting the wrong
command.
If the command completion takes the xhci lock before the timeout work, it
will handle the command, pick the next command, mark it as current_cmd, and
re-queue the timeout work. When the timeout work finally gets the lock
It will start aborting the wrong command.
This case can be resolved by checking if the timeout work is pending inside
the timeout function itself. A new timeout work can only be pending if the
command completed and a new command was queued.
If there are no more commands pending then command completion will set
the current_cmd to NULL, which is already handled in the timeout work.
Baolin Wang [Tue, 3 Jan 2017 16:28:47 +0000 (18:28 +0200)]
usb: host: xhci: Fix possible wild pointer when handling abort command
When current command was supposed to be aborted, host will free the command
in handle_cmd_completion() function. But it might be still referenced by
xhci->current_cmd, which need to set NULL.
Lu Baolu [Tue, 3 Jan 2017 16:28:46 +0000 (18:28 +0200)]
usb: xhci: fix possible wild pointer
handle_cmd_completion() frees a command structure which might be still
referenced by xhci->current_cmd.
This might cause problem when xhci->current_cmd is accessed after that.
A real-life case could be like this. The host takes a very long time to
respond to a command, and the command timer is fired at the same time
when the command completion event arrives. The command completion
handler frees xhci->current_cmd before the timer function can grab
xhci->lock. Afterward, timer function grabs the lock and go ahead with
checking and setting members of xhci->current_cmd.
Pan Bian [Tue, 3 Jan 2017 16:28:45 +0000 (18:28 +0200)]
usb: return error code when platform_get_irq fails
In function xhci_mtk_probe(), variable ret takes the return value. Its
value should be negative on failures. However, when the call to function
platform_get_irq() fails, it does not set the error code, and 0 will be
returned. 0 indicates no error. As a result, the callers of function
xhci_mtk_probe() will not be able to detect the error. This patch fixes
the bug by assigning the return value of platform_get_irq() to variable
ret if it fails.
Lu Baolu [Tue, 3 Jan 2017 16:28:44 +0000 (18:28 +0200)]
usb: xhci: fix return value of xhci_setup_device()
xhci_setup_device() should return failure with correct error number
when xhci host has died, removed or halted.
During usb device enumeration, if usb host is not accessible (died,
removed or halted), the hc_driver->address_device() should return
a corresponding error code to usb core. But current xhci driver just
returns success. This misleads usb core to continue the enumeration
by reading the device descriptor, which will result in failure, and
users will get a misleading message like "device descriptor read/8,
error -110".
Florian Fainelli [Thu, 15 Dec 2016 01:13:24 +0000 (17:13 -0800)]
staging: octeon: Call SET_NETDEV_DEV()
The Octeon driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner") Reported-by: Aaro Koskinen <[email protected]> Cc: stable <[email protected]> # 4.9+ Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Sabrina Dubroca [Tue, 3 Jan 2017 15:26:04 +0000 (16:26 +0100)]
benet: stricter vxlan offloading check in be_features_check
When VXLAN offloading is enabled, be_features_check() tries to check if
an encapsulated packet is indeed a VXLAN packet. The check is not strict
enough, and considers any UDP-encapsulated ethernet frame with a 8-byte
tunnel header as being VXLAN. Unfortunately, both GENEVE and VXLAN-GPE
have a 8-byte header, so they get through this check.
Force the UDP destination port to be the one that has been offloaded to
hardware.
Without this, GENEVE-encapsulated packets can end up having an incorrect
checksum when both a GENEVE and a VXLAN (offloaded) tunnel are
configured.
This is similar to commit a547224dceed ("mlx4e: Do not attempt to
offload VXLAN ports that are unrecognized").
Alexander Duyck [Mon, 2 Jan 2017 21:32:54 +0000 (13:32 -0800)]
ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules
In the case of custom rules being present we need to handle the case of the
LOCAL table being intialized after the new rule has been added. To address
that I am adding a new check so that we can make certain we don't use an
alias of MAIN for LOCAL when allocating a new table.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse") Reported-by: Oliver Brunel <[email protected]> Signed-off-by: Alexander Duyck <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Bartosz Folta [Mon, 2 Jan 2017 12:41:50 +0000 (12:41 +0000)]
net: macb: Updated resource allocation function calls to new version of API.
Changed function calls of resource allocation to new API. Changed way
of setting DMA mask. Removed unnecessary sanity check.
This patch is sent in regard to recently applied patch
Commit 83a77e9ec4150ee4acc635638f7dedd9da523a26
net: macb: Added PCI wrapper for Platform Driver.
David S. Miller [Tue, 3 Jan 2017 14:33:00 +0000 (09:33 -0500)]
Merge branch 'dwmac-oxnas-leaks'
Johan Hovold says:
====================
net: stmmac: dwmac-oxnas: fix leaks and simplify pm
These patches fixes of-node and fixed-phydev leaks in the recently added
dwmac-oxnas driver, and ultimately switches over to using the generic pm
implementation as the required callbacks are now in place.
Note that this series has only been compile tested.
====================
Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by calling the new glue
helper function.
For driver unbind, use the generic stmmac-platform remove implementation
and add an exit callback to disable the clock.
Fixes: 5ed7414062e7 ("net: stmmac: Add OXNAS Glue Driver") Signed-off-by: Johan Hovold <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Johan Hovold [Mon, 2 Jan 2017 11:56:02 +0000 (12:56 +0100)]
net: stmmac: dwmac-oxnas: fix of-node leak
Use the syscon lookup-by-phandle helper so that the reference taken by
of_parse_phandle() is released when done with the node.
Fixes: 5ed7414062e7 ("net: stmmac: Add OXNAS Glue Driver") Signed-off-by: Johan Hovold <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Merge tag 'fixes-for-v4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.10-rc3
The first set of fixes for v4.10-rc cycle. The most
important of which is a big regression on dwc3-pci
which prevents it from probing altogether.
There's also a fix to avoid Overflow events on DWC3
and another to make sure we don't starve DMA
resources.
Dummy HCD got some love after a long hiatus and DWC2
got a couple fixes related to DMA usage. Other than
these, we have a set of minor fixes here and there.
David Lechner [Mon, 2 Jan 2017 23:28:39 +0000 (17:28 -0600)]
usb: gadget: Fix copy/pasted error message
This fixes an error message that was probably copied and pasted. The same
message is used for both the in and out endpoints, so it makes it impossible
to know which one actually failed because both cases say "IN".
ALSA: firewire-lib: change structure member with proper type
The 'amdtp_stream' structure is initialized by a call of
'amdtp_stream_init()'. Although a parameter of this function is for bit
flags of packet attributes, its type is enumerator.
This commit changes the type so that it's proper for a bit flags.
ALSA: fireworks: fix asymmetric API call at unit removal
ALSA fireworks driver has a bug not to call an API to destroy
'cmp_connection' structure for input direction. Currently this causes no
issues because it just destroys 'mutex' structure, while it's better to
fix it for future work.
As the fence may be signaled concurrently from an interrupt on another
device, it is possible for the list of requests on the timeline to be
modified as we walk it. Take both (the context's timeline and the global
timeline) locks to prevent such modifications.
Chris Wilson [Fri, 23 Dec 2016 14:57:58 +0000 (14:57 +0000)]
drm/i915: Silence allocation failure during sg_trim()
As trimming the sg table is merely an optimisation that gracefully fails
if we cannot allocate a new table, we do not need to report the failure
either.
Chris Wilson [Fri, 23 Dec 2016 14:57:57 +0000 (14:57 +0000)]
drm/i915: Don't clflush before release phys object
When we teardown the backing storage for the phys object, we copy from
the coherent contiguous block back to the shmemfs object, clflushing as
we go. Trying to clflush the invalid sg beforehand just oops and would
be redundant (due to it already being coherent, and clflushed
afterwards).
Ville Syrjälä [Wed, 7 Dec 2016 17:56:47 +0000 (17:56 +0000)]
drm/i915: Fix oopses in the overlay code due to i915_gem_active stuff
The i915_gem_active stuff doesn't like a NULL ->retire hook, but
the overlay code can set it to NULL. That obviously ends up oopsing.
Fix it by introducing a new helper to assign the retirement callback
that will switch out the NULL function pointer with
i915_gem_retire_noop.
Ville Syrjälä [Tue, 20 Dec 2016 15:39:02 +0000 (17:39 +0200)]
drm/i915: Move the min_pixclk[] handling to the end of readout
Trying to determine the pixel rate of the pipe can't be done until we
know the clock, which means it can't be done until the encoder
.get_config() hooks have been called. So let's move the min_pixclk[]
stuff to the end of intel_modeset_readout_hw_state() when we actually
have gathered all the required infromation.
Ville Syrjälä [Tue, 20 Dec 2016 16:51:17 +0000 (18:51 +0200)]
drm/i915: Force VDD off on the new power seqeuencer before starting to use it
Apparently some VLV BIOSen like to leave the VDD force bit enabled
even for power seqeuncers that aren't properly hooked up to any
port. That will result in a imbalance in the AUX power domain
refcount when we stat to use said power sequencer as edp_panel_vdd_on()
will not grab the power domain reference if it sees that the VDD is
already on.
To fix this let's make sure we turn off the VDD force bit when we
initialize the power sequencer registers. That is, unless it's
being done from the init path since there we are actually
initializing the registers for the current power sequencer and
we don't want to turn VDD off needlessly as that would require
waiting for the power cycle delay before we turn it back on.
This fixes the following kind of warnings:
WARNING: CPU: 0 PID: 123 at ../drivers/gpu/drm/i915/intel_runtime_pm.c:1455 intel_display_power_put+0x13a/0x170 [i915]()
WARN_ON(!power_domains->domain_use_count[domain])
...
Fabio Estevam [Fri, 30 Dec 2016 10:09:03 +0000 (08:09 -0200)]
ARM: dts: imx6: Disable "weim" node in the dtsi files
Commit 1be81ea5860744520 ("ARM: dts: imx6: Add imx-weim parameters to
dtsi's") causes the following probe error when the weim node is not
present on the board dts (such as imx6q-sabresd):
imx-weim 21b8000.weim: Invalid 'ranges' configuration
imx-weim: probe of 21b8000.weim failed with error -22
There is no need to always enable the "weim" node on mx6. Do the same
as in the other i.MX dtsi files where "weim" is disabled and only gets
enabled on a per dts basis.
All the imx6 weim dts users explicitily provide 'status = "okay"', so
this change has no impact on current imx6 weim users.
If a board does not use the weim driver it will not describe its 'ranges'
property, so simply disable the 'weim' node in the imx6 dtsi files to
avoid such probe error message.
Linus Torvalds [Tue, 3 Jan 2017 02:32:59 +0000 (18:32 -0800)]
Merge tag 'fscrypt-for-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt
Pull fscrypt fixes from Ted Ts'o:
"Two fscrypt bug fixes, one of which was unmasked by an update to the
crypto tree during the merge window"
* tag 'fscrypt-for-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
fscrypt: fix renaming and linking special files
fscrypt: fix the test_dummy_encryption mount option
Chanwoo Choi [Wed, 28 Dec 2016 11:52:36 +0000 (20:52 +0900)]
PM / devfreq: exynos-bus: Fix the wrong return value
This patch fixes the wrong return value. If devfreq driver requires the wrong
and non-available governor, it is fail. So, this patch returns the error
insead of -EPROBE_DEFER.
Fixes: 403e0689d2a9 (PM / devfreq: exynos: Add support of bus frequency of sub-blocks using passive governor) Signed-off-by: Chanwoo Choi <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
Chanwoo Choi [Wed, 28 Dec 2016 11:52:35 +0000 (20:52 +0900)]
PM / devfreq: Fix the bug of devfreq_add_device when governor is NULL
This patch fixes the bug of devfreq_add_device(). The devfreq device must
have the default governor. If find_devfreq_governor() returns error,
devfreq_add_device() fail to add the devfreq instance.
Fixes: 1b5c1be2c88e (PM / devfreq: map devfreq drivers to governor using name) Signed-off-by: Chanwoo Choi <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
Chanwoo Choi [Wed, 28 Dec 2016 11:52:34 +0000 (20:52 +0900)]
MAINTAINERS: Add myself as reviewer for DEVFREQ subsystem support
Add myself to the DEVFREQ entry as reviewer, I've been helping reviewing
and tesing the devfreq support patches for the couple of years. Also,
I'm going to contribute the improvement for devfreq subsystem. It would
be easier for me for review if I'm cc'ed for patches.
PM / docs: Drop confusing kernel-doc references from infrastructure.rst
The references to drivers/base/power/main.c and
drivers/acpi/scan.c from Documentation/driver-api/infrastructure.rst
are confusing. They both cause descriptions of functions that are
not relevant to device drivers at all to be generated and none of
them is sufficient to cover the API in a meaningful way.
ACPI / scan: Prefer devices without _HID/_CID for _ADR matching
The way acpi_find_child_device() works currently is that, if there
are two (or more) devices with the same _ADR value in the same
namespace scope (which is not specifically allowed by the spec and
the OS behavior in that case is not defined), the first one of them
found to be present (with the help of _STA) will be returned.
This covers the majority of cases, but is not sufficient if some of
the devices in question have a _HID (or _CID) returning some valid
ACPI/PNP device IDs (which is disallowed by the spec) and the
ASL writers' expectation appears to be that the OS will match
devices without a valid ACPI/PNP device ID against a given bus
address first.
To cover this special case as well, modify find_child_checks()
to prefer devices without ACPI/PNP device IDs over devices that
have them.
Linus Torvalds [Mon, 2 Jan 2017 20:42:50 +0000 (12:42 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- regression fix (caused by me applying a wrong version of patch) for
sensor-hub driver, from Srinivas Pandruvada
- hid-sony fixes (mostly related to DS4 device) from Roderick
Colenbrander
- three device-specific quirks-fixes from Alex Wood, Brendan McGrath
and Marcel Hasler
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: sensor-hub: Move the memset to sensor_hub_get_feature()
HID: usbhid: Add quirk for Mayflash/Dragonrise DolphinBar.
HID: usbhid: Add quirk for the Futaba TOSD-5711BB VFD
HID: sony: Ignore DS4 dongle reports when no device is connected
HID: sony: Use DS4 MAC address as unique identifier on USB
HID: sony: Fix error handling bug when touchpad registration fails
HID: asus: Fix keyboard support
Michael Walle [Mon, 2 Jan 2017 16:53:39 +0000 (17:53 +0100)]
hwmon: (lm90) fix temp1_max_alarm attribute
Since commit commit eb1c8f4325d5 ("hwmon: (lm90) Convert to use new hwmon
registration API") the temp1_max_alarm and temp1_crit_alarm attributes are
mapped to the same alarm bit. Fix the typo.
Fixes: eb1c8f4325d5 ("hwmon: (lm90) Convert to use new hwmon registration API") Signed-off-by: Micehael Walle <[email protected]> Signed-off-by: Guenter Roeck <[email protected]>
Michal Tesar [Mon, 2 Jan 2017 13:38:36 +0000 (14:38 +0100)]
igmp: Make igmp group member RFC 3376 compliant
5.2. Action on Reception of a Query
When a system receives a Query, it does not respond immediately.
Instead, it delays its response by a random amount of time, bounded
by the Max Resp Time value derived from the Max Resp Code in the
received Query message. A system may receive a variety of Queries on
different interfaces and of different kinds (e.g., General Queries,
Group-Specific Queries, and Group-and-Source-Specific Queries), each
of which may require its own delayed response.
Before scheduling a response to a Query, the system must first
consider previously scheduled pending responses and in many cases
schedule a combined response. Therefore, the system must be able to
maintain the following state:
o A timer per interface for scheduling responses to General Queries.
o A per-group and interface timer for scheduling responses to Group-
Specific and Group-and-Source-Specific Queries.
o A per-group and interface list of sources to be reported in the
response to a Group-and-Source-Specific Query.
When a new Query with the Router-Alert option arrives on an
interface, provided the system has state to report, a delay for a
response is randomly selected in the range (0, [Max Resp Time]) where
Max Resp Time is derived from Max Resp Code in the received Query
message. The following rules are then used to determine if a Report
needs to be scheduled and the type of Report to schedule. The rules
are considered in order and only the first matching rule is applied.
1. If there is a pending response to a previous General Query
scheduled sooner than the selected delay, no additional response
needs to be scheduled.
2. If the received Query is a General Query, the interface timer is
used to schedule a response to the General Query after the
selected delay. Any previously pending response to a General
Query is canceled.
--8<--
Currently the timer is rearmed with new random expiration time for
every incoming query regardless of possibly already pending report.
Which is not aligned with the above RFE.
It also might happen that higher rate of incoming queries can
postpone the report after the expiration time of the first query
causing group membership loss.
Now the per interface general query timer is rearmed only
when there is no pending report already scheduled on that interface or
the newly selected expiration time is before the already pending
scheduled report.
Ian Kumlien [Mon, 2 Jan 2017 08:18:35 +0000 (09:18 +0100)]
flow_dissector: Update pptp handling to avoid null pointer deref.
__skb_flow_dissect can be called with a skb or a data packet, either
can be NULL. All calls seems to have been moved to __skb_header_pointer
except the pptp handling which is still calling skb_header_pointer.
Fixes: ab10dccb1160 ("rps: Inspect PPTP encapsulated by GRE to get flow hash") Signed-off-by: Ian Kumlien <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Mon, 2 Jan 2017 17:08:45 +0000 (09:08 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Two bug fixes for 4.10-rc3"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kbuild: enable modversions for symbols exported from asm
s390/vtime: correct system time accounting
projects / linux.git / log