Ben Hutchings [Thu, 22 Jan 2015 12:40:25 +0000 (12:40 +0000)]
sh_eth: Detach net device when stopping queue to resize DMA rings
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.
I could easily trigger this by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Ben Hutchings [Thu, 22 Jan 2015 12:40:13 +0000 (12:40 +0000)]
sh_eth: Fix padding of short frames on TX
If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding. This could result in leaking sensitive
data. We also pass different lengths to dma_map_single() and
dma_unmap_single().
Use skb_padto() to pad properly, before calling dma_map_single().
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.
Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.
Dave Airlie [Mon, 26 Jan 2015 23:56:13 +0000 (09:56 +1000)]
Merge branch 'drm-fixes-3.19' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Suspend/resume regression fix for 3.19.
* 'drm-fixes-3.19' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Remove rdev->gart.pages_addr array
drm/radeon: Restore GART table contents after pinning it in VRAM v3
drm/radeon: Split off gart_get_page_entry ASIC hook from set_page_entry
David S. Miller [Mon, 26 Jan 2015 23:50:24 +0000 (15:50 -0800)]
Merge branch 'cls_bpf'
Daniel Borkmann says:
====================
Two cls_bpf fixes
Found them while doing a review on act_bpf and going over the
cls_bpf code again. Will also address the first issue in act_bpf
as it needs to be fixed there, too.
====================
Daniel Borkmann [Thu, 22 Jan 2015 09:41:02 +0000 (10:41 +0100)]
net: cls_bpf: fix auto generation of per list handles
When creating a bpf classifier in tc with priority collisions and
invoking automatic unique handle assignment, cls_bpf_grab_new_handle()
will return a wrong handle id which in fact is non-unique. Usually
altering of specific filters is being addressed over major id, but
in case of collisions we result in a filter chain, where handle ids
address individual cls_bpf_progs inside the classifier.
Issue is, in cls_bpf_grab_new_handle() we probe for head->hgen handle
in cls_bpf_get() and in case we found a free handle, we're supposed
to use exactly head->hgen. In case of insufficient numbers of handles,
we bail out later as handle id 0 is not allowed.
Daniel Borkmann [Thu, 22 Jan 2015 09:41:01 +0000 (10:41 +0100)]
net: cls_bpf: fix size mismatch on filter preparation
In cls_bpf_modify_existing(), we read out the number of filter blocks,
do some sanity checks, allocate a block on that size, and copy over the
BPF instruction blob from user space, then pass everything through the
classic BPF checker prior to installation of the classifier.
We should reject mismatches here, there are 2 scenarios: the number of
filter blocks could be smaller than the provided instruction blob, so
we do a partial copy of the BPF program, and thus the instructions will
either be rejected from the verifier or a valid BPF program will be run;
in the other case, we'll end up copying more than we're supposed to,
and most likely the trailing garbage will be rejected by the verifier
as well (i.e. we need to fit instruction pattern, ret {A,K} needs to be
last instruction, load/stores must be correct, etc); in case not, we
would leak memory when dumping back instruction patterns. The code should
have only used nla_len() as Dave noted to avoid this from the beginning.
Anyway, lets fix it by rejecting such load attempts.
Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier") Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Jiri Pirko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Dave Airlie [Mon, 26 Jan 2015 23:48:33 +0000 (09:48 +1000)]
Merge tag 'drm-amdkfd-fixes-2015-01-26' of git://people.freedesktop.org/~gabbayo/linux into drm-fixes
A couple of fixes for -rc7 in amdkfd:
- Forgot to free resources when creation of queue has failed
- Initialization of pipelines was incorrect (3 patches)
In addition, The patch "drm/amdkfd: Allow user to limit only queues per device"
is not a fix, but I would like to push it for 3.19 as it changes the ABI
between amdkfd and userspace (by changing the module parameters). I would
prefer *not* to support the two deprecated module parameters if I don't have
too, as amdkfd hasn't been released yet.
* tag 'drm-amdkfd-fixes-2015-01-26' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Fix bug in call to init_pipelines()
drm/amdkfd: Fix bug in pipelines initialization
drm/radeon: Don't increment pipe_id in kgd_init_pipeline
drm/amdkfd: Allow user to limit only queues per device
drm/amdkfd: PQM handle queue creation fault
David S. Miller [Mon, 26 Jan 2015 23:24:14 +0000 (15:24 -0800)]
Merge tag 'linux-can-fixes-for-3.19-20150121' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-01-21
this is a pull request for v3.19, net/master, which consists of a single patch.
Viktor Babrian fixes the issue in the c_can dirver, that the CAN interface
might continue to send frames after the interface has been shut down.
====================
Linus Torvalds [Mon, 26 Jan 2015 23:17:34 +0000 (15:17 -0800)]
Merge branch 'for-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"The lifetime rules of cgroup hierarchies always have been somewhat
counter-intuitive and cgroup core tried to enforce that hierarchies
w/o userland-visible usages must die in finite amount of time so that
the controllers can be reused for other hierarchies; unfortunately,
this can't be implemented reasonably for the memory controller - the
kmemcg part doesn't have any way to forcefully drain the existing
usages, leading to an interruptible hang if a following mount attempts
to use the controller in any way.
So, it seems like we're stuck with "hierarchies live on till they die
whenever that may be" at least for now. This pretty much confines
attaching controllers to hierarchies to before the hierarchies are
actively used by making dynamic configurations post active usages
unreliable. This has never been reliable and should be fine in
practice given how cgroups are used.
After the patch, hierarchies aren't killed if it isn't already
drained. A following mount attempt of the same mount options will
reuse the existing hierarchy. Mount attempts with differing options
will fail w/ -EBUSY"
* 'for-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: prevent mount hang due to memory controller lifetime
Dave Airlie [Mon, 26 Jan 2015 23:12:53 +0000 (09:12 +1000)]
Merge branch 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm into drm-fixes
3 fixes for the tda998x.
* 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: set the CEC I2C address based on the slave I2C address
drm: tda998x: Fix EDID read timeout on HDMI connect
drm: tda998x: Protect the page register
Linus Torvalds [Mon, 26 Jan 2015 22:52:08 +0000 (14:52 -0800)]
Merge tag 'regulator-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One correctness fix here for the s2mps11 driver which would have
resulted in some of the regulators being completely broken together
with a fix for locking in regualtor_put() (which is fortunately rarely
called at all in practical systems)"
* tag 'regulator-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mps11: Fix wrong calculation of register offset
regulator: core: fix race condition in regulator_put()
Linus Torvalds [Mon, 26 Jan 2015 22:51:19 +0000 (14:51 -0800)]
Merge tag 'spi-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here, some fixes for issues introduced and
discovered during recent work on the DesignWare driver (which has been
getting a lot of attention recently) and a couple of other drivers.
All serious things for people who run into them"
* tag 'spi-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dw: amend warning message
spi: sh-msiof: fix MDR1_FLD_MASK value
spi: dw-mid: fix FIFO size
spi: dw: Fix detecting FIFO depth
spi/pxa2xx: Clear cur_chip pointer before starting next message
Greg Thelen [Mon, 26 Jan 2015 20:58:38 +0000 (12:58 -0800)]
memcg: remove extra newlines from memcg oom kill log
Commit e61734c55c24 ("cgroup: remove cgroup->name") added two extra
newlines to memcg oom kill log messages. This makes dmesg hard to read
and parse. The issue affects 3.15+.
Example:
Task in /t <<< extra #1
killed as a result of limit of /t
<<< extra #2
memory: usage 102400kB, limit 102400kB, failcnt 274712
Remove the extra newlines from memcg oom kill messages, so the messages
look like:
Task in /t killed as a result of limit of /t
memory: usage 102400kB, limit 102400kB, failcnt 240649
Kees Cook [Mon, 26 Jan 2015 20:58:35 +0000 (12:58 -0800)]
x86, build: replace Perl script with Shell script
Commit e6023367d779 ("x86, kaslr: Prevent .bss from overlaping initrd")
added Perl to the required build environment. This reimplements in
shell the Perl script used to find the size of the kernel with bss and
brk added.
Johannes Weiner [Mon, 26 Jan 2015 20:58:32 +0000 (12:58 -0800)]
mm: page_alloc: embed OOM killing naturally into allocation slowpath
The OOM killing invocation does a lot of duplicative checks against the
task's allocation context. Rework it to take advantage of the existing
checks in the allocator slowpath.
The OOM killer is invoked when the allocator is unable to reclaim any
pages but the allocation has to keep looping. Instead of having a check
for __GFP_NORETRY hidden in oom_gfp_allowed(), just move the OOM
invocation to the true branch of should_alloc_retry(). The __GFP_FS
check from oom_gfp_allowed() can then be moved into the OOM avoidance
branch in __alloc_pages_may_oom(), along with the PF_DUMPCORE test.
__alloc_pages_may_oom() can then signal to the caller whether the OOM
killer was invoked, instead of requiring it to duplicate the order and
high_zoneidx checks to guess this when deciding whether to continue.
David Ahern [Fri, 19 Dec 2014 02:11:11 +0000 (19:11 -0700)]
tools lib traceevent: Add support for IP address formats
Add helpers for the following kernel formats:
%pi4 print an IPv4 address with leading zeros
%pI4 print an IPv4 address without leading zeros
%pi6 print an IPv6 address without colons
%pI6 print an IPv6 address with colons
%pI6c print an IPv6 address in compressed form with colons
%pISpc print an IP address from a sockaddr
Allows these formats to be used in tracepoints.
Quite a bit of this is adapted from code in lib/vsprintf.c.
v4:
- fixed pI6c description in git commit message per Valdis' comment
v3:
- use of 'c' and 'p' requires 'I'
v2:
- pass ptr+1 to print_ip_arg per Namhyung's comments
- added field length checks to sockaddr function
Clemens Ladisch [Sun, 25 Jan 2015 13:34:29 +0000 (14:34 +0100)]
ALSA: seq-dummy: remove deadlock-causing events on close
When the last subscriber to a "Through" port has been removed, the
subscribed destination ports might still be active, so it would be
wrong to send "all sounds off" and "reset controller" events to them.
The proper place for such a shutdown would be the closing of the actual
MIDI port (and close_substream() in rawmidi.c already can do this).
This also fixes a deadlock when dummy_unuse() tries to send events to
its own port that is already locked because it is being freed.
Thierry Reding [Fri, 23 Jan 2015 15:37:52 +0000 (16:37 +0100)]
iommu/tegra: gart: Provide default ->map_sg() callback
Commit 315786ebbf4a ("iommu: Add iommu_map_sg() function") adds a new
->map_sg() callback and provides a default implementation that drivers
can use until they implement a hardware-specific variant. Unfortunately
the Tegra GART driver was not updated as part of that commit, so that
iommu_map_sg() calls on a domain provided by the GART cause an oops.
Thierry Reding [Fri, 23 Jan 2015 15:37:51 +0000 (16:37 +0100)]
iommu/tegra: gart: Do not register with bus
The driver currently doesn't work as expected and causes existing setups
with Tegra20 to break after commit df06b759f2cf ("drm/tegra: Add IOMMU
support"). To restore these setups, do not register the operations with
the platform bus for now. Fixing this properly will involve non-trivial
changes to the DRM driver, which are unlikely to be accepted at this
point in the release cycle.
Takashi Iwai [Mon, 26 Jan 2015 12:33:39 +0000 (13:33 +0100)]
Merge tag 'asoc-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.19
There's a lot more fixes here than I'd like since I've been lax in
sending things throughout the release cycle but there's only two in
generic code and they've had quite some time to cook in -next so
hopefully on balance are OK.
The two generic fixes are a fix for crashes on capture DAIs in the
compress code and a fix for error handling on probe failures which would
have been harmless in the past but now oopses with the new dynamic probe
code.
Rodrigo Vivi [Wed, 21 Jan 2015 18:33:53 +0000 (10:33 -0800)]
drm/i915: Fix and clean BDW PCH identification
It seems in the past we have BDW with PCH not been propperly identified
and we force it to be LPT and we were warning !IS_HASWELL on propper identification.
Now that products are out there we are receiveing logs with this incorrect WARN.
And also according to local tests on all production BDW here ULT or HALO we don't
need this force anymore. So let's clean this block for real.
v2: Fix LPT_LP WARNs to avoid wrong warns on BDW_ULT (By Jani).
Bob Paauwe [Thu, 18 Dec 2014 17:51:26 +0000 (09:51 -0800)]
drm/i915: Only fence tiled region of object.
When creating a fence for a tiled object, only fence the area that
makes up the actual tiles. The object may be larger than the tiled
area and if we allow those extra addresses to be fenced, they'll
get converted to addresses beyond where the object is mapped. This
opens up the possiblity of writes beyond the end of object.
To prevent this, we adjust the size of the fence to only encompass
the area that makes up the actual tiles. The extra space is considered
un-tiled and now behaves as if it was a linear object.
drm/i915: respect the VBT minimum backlight brightness
introduced a bug which resulted in inconsistent brightness levels on
different machines. If a suspended was entered with the screen off some
machines would resume with the screen at minimum brightness and others
at maximum brightness.
The following commands can be used to produce this behavior.
xset dpms force off
sleep 1
sudo systemctl suspend
(resume ...)
The root cause of this problem is a comparison which checks to see if
the backlight level is zero when the panel is enabled. If it is zero,
it is set to the maximum level. Unfortunately, not all machines have a
minimum level of zero. On those machines the level is left at the
minimum instead of begin set to the maximum.
Fix the bug by updating the comparison to check for the minimum
backlight level instead of zero. Also, expand the comparison for
the possible case when the level is less than the minimum.
Fixes: 6dda730e55f4 ("respect the VBT minimum backlight brightness") Signed-off-by: Jeremiah Mahler <[email protected]> Signed-off-by: Jani Nikula <[email protected]>
David Woodhouse [Tue, 20 Jan 2015 17:21:42 +0000 (17:21 +0000)]
drm/i915: Init PPGTT before context enable
Commit 82460d972 ("drm/i915: Rework ppgtt init to no require an aliasing
ppgtt") introduced a regression on Broadwell, triggering the following
IOMMU fault at startup:
I sugggested this change to David after staring at the offending patch
for a while. I have no idea and theory whatsoever why this would upset
the gpu less than the other way round. But it seems to work. David
promised to chase hw people a bit more to get a more meaningful answer.
Wrt the comment that this deletes: I've done some digging and afaict
loading context before ppgtt enable was once required before our recent
restructuring of the context/ppgtt init code: Before that context sw
setup (i.e. allocating the default context) and hw setup was smashed
together. Also the setup of the default context was the bit that
actually allocated the aliasing ppgtt structures. Which is the reason
for the context before ppgtt depency.
Or was, since with all the untangling there's no no real depency any
more (functional, who knows what the hw is doing), so the comment is
just stale.
Today we expect that all the bank are enabled, and count the number of banks
used by the pinctrl based on it instead of using the last bank id enabled.
So switch to it, set the chained IRQ at runtime based on enabled banks
and wait only the number of enabled gpio controllers at probe time.
David S. Miller [Mon, 26 Jan 2015 07:38:20 +0000 (23:38 -0800)]
Merge branch 's390'
Ursula Braun says:
====================
s390/qeth patches for net
here are two s390/qeth patches built for net.
One patch is quite large, but we would like to fix the locking warning
seen in recent kernels as soon as possible. But if you want me to submit
these patches for net-next, I will do.
Or Gerlitz says:
====================
Thomas Richter [Wed, 21 Jan 2015 12:39:10 +0000 (13:39 +0100)]
390/qeth: Fix locking warning during qeth device setup
Do not wait for channel command buffers in IPA commands.
The potential wait could be done while holding a spin lock and causes
in recent kernels such a bug if kernel lock debugging is enabled:
The device driver has plenty of command buffers available
per channel for channel command communication.
In the extremely rare case when there is no command buffer
available, return a NULL pointer and issue a warning
in the kernel log. The caller handles the case when
a NULL pointer is encountered and returns an error.
In the case the wait for command buffer is possible
(because no lock is held as in the OSN case), still wait
until a channel command buffer is available.
Eugene Crosser [Wed, 21 Jan 2015 12:39:09 +0000 (13:39 +0100)]
qeth: clean up error handling
In the functions that are registering and unregistering MAC
addresses in the qeth-handled hardware, remove callback functions
that are unnesessary, as only the return code is analyzed.
Translate hardware response codes to semi-standard 'errno'-like
codes for readability.
Add kernel-doc description to the internal API function
qeth_send_control_data().
Martin KaFai Lau [Wed, 21 Jan 2015 03:16:02 +0000 (19:16 -0800)]
ipv6: Fix __ip6_route_redirect
In my last commit (a3c00e4: ipv6: Remove BACKTRACK macro), the changes in
__ip6_route_redirect is incorrect. The following case is missed:
1. The for loop tries to find a valid gateway rt. If it fails to find
one, rt will be NULL.
2. When rt is NULL, it is set to the ip6_null_entry.
3. The newly added 'else if', from a3c00e4, will stop the backtrack from
happening.
Linus Torvalds [Mon, 26 Jan 2015 02:11:17 +0000 (18:11 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Hopefully the last round of fixes for 3.19
- regression fix for the LDT changes
- regression fix for XEN interrupt handling caused by the APIC
changes
- regression fixes for the PAT changes
- last minute fixes for new the MPX support
- regression fix for 32bit UP
- fix for a long standing relocation issue on 64bit tagged for stable
- functional fix for the Hyper-V clocksource tagged for stable
- downgrade of a pr_err which tends to confuse users
Looks a bit on the large side, but almost half of it are valuable
comments"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
x86, tls, ldt: Stop checking lm in LDT_empty
x86, mpx: Strictly enforce empty prctl() args
x86, mpx: Fix potential performance issue on unmaps
x86, mpx: Explicitly disable 32-bit MPX support on 64-bit kernels
x86, hyperv: Mark the Hyper-V clocksource as being continuous
x86: Don't rely on VMWare emulating PAT MSR correctly
x86, irq: Properly tag virtualization entry in /proc/interrupts
x86, boot: Skip relocs when load address unchanged
x86/xen: Override ACPI IRQ management callback __acpi_unregister_gsi
ACPI: pci: Do not clear pci_dev->irq in acpi_pci_irq_disable()
x86/xen: Treat SCI interrupt as normal GSI interrupt
Linus Torvalds [Mon, 26 Jan 2015 02:07:01 +0000 (18:07 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"From the irqchip departement you get:
- regression fix for omap-intc
- regression fix for atmel-aic-common
- functional correctness fix for hip04
- type mismatch fix for gic-v3-its
- proper error pointer check for mtd-sysirq
Mostly one and two liners except for the omap regression fix which is
slightly larger than desired"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: atmel-aic-common: Prevent clobbering of priority when changing IRQ type
irqchip: omap-intc: Fix legacy DMA regression
irqchip: gic-v3-its: Fix use of max with decimal constant
irqchip: hip04: Initialize hip04_cpu_map to 0xffff
irqchip: mtk-sysirq: Use IS_ERR() instead of NULL pointer check
Linus Torvalds [Mon, 26 Jan 2015 01:47:34 +0000 (17:47 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A set of small fixes:
- regression fix for exynos_mct clocksource
- trivial build fix for kona clocksource
- functional one liner fix for the sh_tmu clocksource
- two validation fixes to prevent (root only) data corruption in the
kernel via settimeofday and adjtimex. Tagged for stable"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: adjtimex: Validate the ADJ_FREQUENCY values
time: settimeofday: Validate the values of tv from user
clocksource: sh_tmu: Set cpu_possible_mask to fix SMP broadcast
clocksource: kona: fix __iomem annotation
clocksource: exynos_mct: Fix bitmask regression for exynos4_mct_write
Linus Torvalds [Mon, 26 Jan 2015 01:29:06 +0000 (17:29 -0800)]
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A week's worth of fixes for various ARM platforms. Diff wise, the
largest fix is for OMAP to deal with how GIC now registers interrupts
(irq_domain_add_legacy() -> irq_domain_add_linear() changes).
Besides this, a few more renesas platforms needed the GIC instatiation
done for legacy boards. There's also a fix that disables coherency of
mvebu due to issues, and a few other smaller fixes"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: add baud rate to Juno stdout-path
ARM: dts: imx25: Fix PWM "per" clocks
bus: mvebu-mbus: fix support of MBus window 13
Merge tag 'mvebu-fixes-3.19-3' of git://git.infradead.org/linux-mvebu into fixes
ARM: mvebu: completely disable hardware I/O coherency
ARM: OMAP: Work around hardcoded interrupts
ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
Linus Torvalds [Mon, 26 Jan 2015 01:27:18 +0000 (17:27 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes - deadlock in CIFS and build breakage in cris serial
driver (resurfaced f_dentry in there)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
VFS: Convert file->f_dentry->d_inode to file_inode()
fix deadlock in cifs_ioctl_clone()
Linus Torvalds [Mon, 26 Jan 2015 01:25:01 +0000 (17:25 -0800)]
Merge tag 'dm-3.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two stable fixes for dm-cache and one 3.19 DM core fix:
- fix potential for dm-cache metadata corruption via stale metadata
buffers being used when switching an inactive cache table to
active; this could occur due to each table having it's own bufio
client rather than sharing the client between tables.
- fix dm-cache target to properly account for discard IO while
suspending otherwise IO quiescing could complete prematurely.
- fix DM core's handling of multiple internal suspends by maintaining
an 'internal_suspend_count' and only resuming the device when this
count drops to zero"
* tag 'dm-3.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix handling of multiple internal suspends
dm cache: fix problematic dual use of a single migration count variable
dm cache: share cache-metadata object across inactive and active DM tables
Linus Torvalds [Mon, 26 Jan 2015 01:23:34 +0000 (17:23 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull two block layer fixes from Jens Axboe:
"Two small patches that should make it into 3.19:
- a fixup from me for NVMe, making the cq_vector a signed variable.
Otherwise our -1 comparison fails, and commit 2b25d981790b doesn't
do what it was supposed to.
- a fixup for the hotplug handling for blk-mq from Ming Lei, using
the proper kobject referencing to ensure we release resources at
the right time"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: fix hctx/ctx kobject use-after-free
NVMe: cq_vector should be signed
Vivien Didelot [Wed, 21 Jan 2015 00:13:32 +0000 (19:13 -0500)]
net: dsa: set slave MII bus PHY mask
When registering a mdio bus, Linux assumes than every port has a PHY and tries
to scan it. If a switch port has no PHY registered, DSA will fail to register
the slave MII bus. To fix this, set the slave MII bus PHY mask to the switch
PHYs mask.
As an example, if we use a Marvell MV88E6352 (which is a 7-port switch with no
registered PHYs for port 5 and port 6), with the following declared names:
DSA will fail to create the switch instance. With the PHY mask set for the
slave MII bus, only the PHY for ports 0-4 will be scanned and the instance will
be successfully created.
Maxime Ripard [Thu, 22 Jan 2015 21:10:54 +0000 (22:10 +0100)]
ARM: sunxi: dt: Fix aliases
Commit f77d55a3b56a ("serial: 8250_dw: get index of serial line from DT
aliases") made the serial driver now use the serial aliases to get the tty
number, pointing out that our aliases have been wrong all along.
Remove them from the DTSI and add custom ones in the relevant boards.
Macpaul Lin [Fri, 23 Jan 2015 06:39:02 +0000 (14:39 +0800)]
USB: Add OTG PET device to TPL
OTG device shall support this device for allowing compliance automated testing.
The modification is derived from Pavankumar and Vijayavardhans' previous work.
Mark Knibbs [Mon, 19 Jan 2015 17:42:10 +0000 (17:42 +0000)]
storage: Revise/fix quirk for 04E6:000F SCM USB-SCSI converter
I recently posted a patch ("storage: Add quirk for another SCM-based
USB-SCSI converter") to add a quirk for the converter with ID 04E6:000F,
which is listed along with 04E6:000B in the Windows INF file for the
Startech ICUSBSCSI2 as "eUSB SCSI Adapter (Bus Powered)".
The already-present quirk for 04E6:000B has USB_SC_SCSI/USB_PR_BULK, not
USB_SC_DEVICE/USB_PR_DEVICE. Change the 04E6:000F quirk to match that,
since it will probably be required.
Marc Dietrich [Tue, 20 Jan 2015 22:01:28 +0000 (23:01 +0100)]
staging: nvec: specify a platform-device base id
commit 6e3f62f079 (mfd: core: Fix platform-device id generation) modified
the computation of the mfd cell id. Negative numbers forbit the specification
of cell ids as we do. Fix this for now by specifying a base of 0 instead. In
the long run, this may be changed to automatic cell ids (base -2).
Mahesh Bandewar [Sun, 25 Jan 2015 05:53:43 +0000 (21:53 -0800)]
ipvlan: fix incorrect usage of IS_ERR() macro in IPv6 code path.
The ip6_route_output() always returns a valid dst pointer unlike in IPv4
case. So the validation has to be different from the IPv4 path. Correcting
that error in this patch.
This was picked up by a static checker with a following warning -
drivers/net/ipvlan/ipvlan_core.c:380 ipvlan_process_v6_outbound()
warn: 'dst' isn't an ERR_PTR
Sasha Levin [Sat, 24 Jan 2015 01:47:00 +0000 (20:47 -0500)]
net: llc: use correct size for sysctl timeout entries
The timeout entries are sizeof(int) rather than sizeof(long), which
means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
With the commit d75b1ade567ffab ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. When we are in busy_poll we return 0 in
napi_poll. We should return budget.
* A fix that improves roaming behavior. Same fix has been tested for
a while in iwldvm. This is a bit of a work around, but the real fix
should be in mac80211 and will come later.
* A fix for BARs that avoids a WARNING.
* one fix for rfkill while scheduled scan is running.
Linus's system hit this issue. WiFi would be unavailable
after this has happpened because of bad state in cfg80211.
Linus Torvalds [Sat, 24 Jan 2015 22:52:30 +0000 (14:52 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
pULL SCSI fixes from James Bottomley:
"This consists of four real fixes and three MAINTAINER updates.
Three of the fixes are obvious (the DIX and atomic allocation are bug
on and warn on fixes and the other is just trivial) and the ipr one is
a bit more involved but is required because without it, the card
double completes aborted commands and causes a kernel oops"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ibmvscsi driver maintainer change
MAINTAINERS: ibmvfc driver maintainer change
MAINTAINERS: Remove self as isci maintainer
scsi_debug: test always evaluates to false, || should be used instead
scsi: Avoid crashing if device uses DIX but adapter does not support it
scsi_debug: use atomic allocation in resp_rsup_opcodes
ipr: wait for aborted command responses
Linus Torvalds [Sat, 24 Jan 2015 22:47:24 +0000 (14:47 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"This will fix reboot issues with the imx2_wdt driver and it also drops
some forgotten owner assignments from platform_drivers"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: drop owner assignment from platform_drivers
watchdog: imx2_wdt: Disable power down counter on boot
watchdog: imx2_wdt: Improve power management support.
Linus Torvalds [Sat, 24 Jan 2015 22:37:31 +0000 (14:37 -0800)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull hwmon update from Jean Delvare:
"This contains a single thing: a new driver for the temperature sensor
embedded in the Intel 5500/5520/X58 chipsets.
Sorry for the late request, it's been so long since I last sent a pull
request and I've been so busy with other tasks meanwhile that I simply
forgot about these patches. But given that this is a new driver, it
can't introduce any regression so I thought it could still be OK.
This has been in linux-next for months now"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
hwmon: (i5500_temp) Convert to module_pci_driver
hwmon: (i5500_temp) Don't bind to disabled sensors
hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
Linus Torvalds [Sat, 24 Jan 2015 22:34:54 +0000 (14:34 -0800)]
Merge tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fix some race conditions caused by a regression on videobuf2
- fix a interrupt release bug on cx23885
- fix support for Mygica T230 and HVR4400
- fix compilation breakage when USB is not selected on tlg2300
- fix capabilities report on ompa3isp, soc-camera, rcar_vin and
pvrusb2
* tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] omap3isp: Correctly set QUERYCAP capabilities
[media] cx23885: fix free interrupt bug
[media] pvrusb2: fix missing device_caps in querycap
[media] vb2: fix vb2_thread_stop race conditions
[media] rcar_vin: Update device_caps and capabilities in querycap
[media] soc-camera: fix device capabilities in multiple camera host drivers
[media] Fix Mygica T230 support
[media] cx23885: Split Hauppauge WinTV Starburst from HVR4400 card entry
[media] tlg2300: Fix media dependencies
Mikulas Patocka [Thu, 8 Jan 2015 23:52:26 +0000 (18:52 -0500)]
dm: fix handling of multiple internal suspends
Commit ffcc393641 ("dm: enhance internal suspend and resume interface")
attempted to handle multiple internal suspends on the same device, but
it did that incorrectly. When these functions are called in this order
on the same device the device is no longer suspended, but it should be:
dm_internal_suspend_noflush
dm_internal_suspend_noflush
dm_internal_resume
Fix this bug by maintaining an 'internal_suspend_count' and resuming
the device when this count drops to zero.
Jean Delvare [Sat, 24 Jan 2015 13:16:21 +0000 (14:16 +0100)]
hwmon: (i5500_temp) Don't bind to disabled sensors
On many motherboards, for an unknown reason, the thermal sensor seems
to be disabled and will return a constant temperature value of 36.5
degrees Celsius. Don't bind to the device in that case, so that we
don't report this bogus value to userspace.
Lendacky, Thomas [Tue, 20 Jan 2015 18:20:31 +0000 (12:20 -0600)]
amd-xgbe: Use proper Rx flow control register
Updated hardware documention shows the Rx flow control settings were
moved from the Rx queue operation mode register to a new Rx queue flow
control register. The old flow control settings are now reserved areas
of the Rx queue operation mode register. Update the code to use the new
register.
Paul Osmialowski [Mon, 19 Jan 2015 16:03:33 +0000 (17:03 +0100)]
i2c: s3c2410: fix ABBA deadlock by keeping clock prepared
This patch solves deadlock between clock prepare mutex and regmap mutex reported
by Tomasz Figa in [1] by implementing solution from [2]: "always leave the clock
of the i2c controller in a prepared state".
On each i2c transfer handled by s3c24xx_i2c_xfer(), clk_prepare_enable() was
called, which calls clk_prepare() then clk_enable(). clk_prepare() takes
prepare_lock mutex before proceeding. Note that i2c transfer functions are
invoked from many places in kernel, typically with some other additional lock
held.
It may happen that function on CPU1 (e.g. regmap_update_bits()) has taken a
mutex (i.e. regmap lock mutex) then it attempts i2c communication in order to
proceed (so it needs to obtain clock related prepare_lock mutex during transfer
preparation stage due to clk_prepare() call). At the same time other task on
CPU0 wants to operate on clock (e.g. to (un)prepare clock for some other reason)
so it has taken prepare_lock mutex.
Implemented solution from [2] leaves i2c clock prepared. Preparation is done in
s3c24xx_i2c_probe() function. Without this patch, it is immediately unprepared
by clk_disable_unprepare() call. I've replaced this call with clk_disable() and
I've added clk_unprepare() call in s3c24xx_i2c_remove().
The s3c24xx_i2c_xfer() function now uses clk_enable() instead of
clk_prepare_enable() (and clk_disable() instead of clk_unprepare_disable()).
Lee Jones [Thu, 28 Aug 2014 14:02:03 +0000 (15:02 +0100)]
i2c: st: Rename clock reference to something that exists
CLK_S_ICN_REG_0 hasn't existed for a while now. This was renamed
over a few commits, then finally removed in commit 5aa02b9 (ARM:
STi: DT: STiH415: Remove unused CLK_S_ICN_REG_0 fixed clock).
Linus Torvalds [Sat, 24 Jan 2015 02:31:27 +0000 (14:31 +1200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We have a few fixes in my for-linus branch.
Qu Wenruo's batch fix a regression between some our merge window pull
and the inode_cache feature. The rest are smaller bugs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: Don't call btrfs_start_transaction() on frozen fs to avoid deadlock.
btrfs: Fix the bug that fs_info->pending_changes is never cleared.
btrfs: fix state->private cast on 32 bit machines
Btrfs: fix race deleting block group from space_info->ro_bgs list
Btrfs: fix incorrect freeing in scrub_stripe
btrfs: sync ioctl, handle errors after transaction start
Linus Torvalds [Fri, 23 Jan 2015 23:26:13 +0000 (11:26 +1200)]
Merge tag 'platform-drivers-x86-v3.19-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull platform driver fix from Darren Hart:
"Revert keyboard backlight sysfs support and documentation.
The support for the dell-laptop keyboard backlight was flawed and the
fix:
https://lkml.org/lkml/2015/1/14/539
was more invasive that I felt comfortable sending at RC5.
This series reverts the support for the dell-laptop keyboard backlight
as well as the documentation for the newly created sysfs attributes.
We'll get this implemented correctly for 3.20"
* tag 'platform-drivers-x86-v3.19-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
Revert "Documentation: Add entry for dell-laptop sysfs interface"
Linus Torvalds [Fri, 23 Jan 2015 22:58:47 +0000 (10:58 +1200)]
Merge tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for:
- a resource management problem that causes a Radeon "Fatal error
during GPU init" on machines where the BIOS programmed an invalid
Root Port window. This was a regression in v3.16.
- an Atheros AR93xx device that doesn't handle PCI bus resets
correctly. This was a regression in v3.14.
- an out-of-date email address"
* tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update Richard Zhu's email address
sparc/PCI: Clip bridge windows to fit in upstream windows
powerpc/PCI: Clip bridge windows to fit in upstream windows
parisc/PCI: Clip bridge windows to fit in upstream windows
mn10300/PCI: Clip bridge windows to fit in upstream windows
microblaze/PCI: Clip bridge windows to fit in upstream windows
ia64/PCI: Clip bridge windows to fit in upstream windows
frv/PCI: Clip bridge windows to fit in upstream windows
alpha/PCI: Clip bridge windows to fit in upstream windows
x86/PCI: Clip bridge windows to fit in upstream windows
PCI: Add pci_claim_bridge_resource() to clip window if necessary
PCI: Add pci_bus_clip_resource() to clip to fit upstream window
PCI: Pass bridge device, not bus, when updating bridge windows
PCI: Mark Atheros AR93xx to avoid bus reset
PCI: Add flag for devices where we can't use bus reset
Linus Torvalds [Fri, 23 Jan 2015 22:55:05 +0000 (10:55 +1200)]
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree bug fixes and documentation updates from Grant Likely:
"A few bugfixes for the new DT overlay feature, documentation updates,
spelling corrections, and changes to MAINTAINERS. Nothing earth
shattering here"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Overlays with sub-devices tests
of/platform: Handle of_populate drivers in notifier
of/overlay: Do not generate duplicate nodes
devicetree: document the "qemu" and "virtio" vendor prefixes
devicetree: document ARM bindings for QEMU's Firmware Config interface
Documentation: of: fix typo in graph bindings
dma-mapping: fix debug print to display correct dma_pfn_offset
of: replace Asahi Kasei Corp vendor prefix
ARM: dt: GIC: Spelling s/specific/specifier/, s/flaggs/flags/
dt/bindings: arm-boards: Spelling s/pointong/pointing/
MAINTAINERS: Update DT website and git repository
MAINTAINERS: drop DT regex matching on of_get_property and of_match_table
Robin Murphy [Thu, 22 Jan 2015 11:21:32 +0000 (11:21 +0000)]
arm64: dts: add baud rate to Juno stdout-path
Without explicit command-line parameters, the Juno UART ends up running
at 57600 baud in the kernel, which is at odds with the 115200 baud used
by the rest of the firmware. Since commit 7914a7c5651a5161 now lets us
fix this by specifying default options in stdout-path, do so.
Olof Johansson [Fri, 23 Jan 2015 22:08:13 +0000 (14:08 -0800)]
Merge tag 'mvebu-fixes-3.19-4' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu/fixes #3" from Andrew Lunn:
mvebu fixes for 3.19. (Part 4)
bus: mvebu-mbus: fix support of MBus window 13
* tag 'mvebu-fixes-3.19-4' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: fix support of MBus window 13
ARM: mvebu: completely disable hardware I/O coherency
Linus Torvalds [Fri, 23 Jan 2015 21:58:17 +0000 (09:58 +1200)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Three small fixes.
Two for x86 and one avoids that sparse bails out"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: SYSENTER emulation is broken
KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
KVM: fix sparse warning in include/trace/events/kvm.h
Linus Torvalds [Fri, 23 Jan 2015 21:57:01 +0000 (09:57 +1200)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Another round of small ARM fixes.
restore_user_regs early stack deallocation is buggy in the presence of
FIQs which switch to SVC mode, and could lead to corrupted registers
being returned to a user process given an inopportune FIQ event.
Another bug was spotted in the ARM perf code where it could lose track
of perf counter overflows, leading to incorrect perf results.
Lastly, a bug in arm_add_memory() was spotted where the memory sizes
aren't properly rounded. As most people pass properly rounded sizes,
this hasn't been noticed"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8292/1: mm: fix size rounding-down of arm_add_memory() function
ARM: 8255/1: perf: Prevent wraparound during overflow
ARM: 8266/1: Remove early stack deallocation from restore_user_regs
Linus Torvalds [Fri, 23 Jan 2015 21:55:13 +0000 (09:55 +1200)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull two arm64 fixes from Will Deacon:
"Arm64 fixes seem to come in pairs recently. We've got a fix for
removing device-tree blobs when doing a make clean and another one
addressing a missing include, which fixes build failures in -next for
allmodconfig (spotted by Mark's buildbot).
Summary from signed tag:
- fix cleaning of .dtbs following directory restructuring
- fix allmodconfig build breakage in -next due to missing include"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: dump: Fix implicit inclusion of definition for PCI_IOBASE
arm64: Add dtb files to archclean rule
Joe Thornber [Fri, 23 Jan 2015 10:16:16 +0000 (10:16 +0000)]
dm cache: fix problematic dual use of a single migration count variable
Introduce a new variable to count the number of allocated migration
structures. The existing variable cache->nr_migrations became
overloaded. It was used to:
i) track of the number of migrations in flight for the purposes of
quiescing during suspend.
ii) to estimate the amount of background IO occuring.
Recent discard changes meant that REQ_DISCARD bios are processed with
a migration. Discards are not background IO so nr_migrations was not
incremented. However this could cause quiescing to complete early.
(i) is now handled with a new variable cache->nr_allocated_migrations.
cache->nr_migrations has been renamed cache->nr_io_migrations.
cleanup_migration() is now called free_io_migration(), since it
decrements that variable.
Also, remove the unused cache->next_migration variable that got replaced
with with prealloc_structs a while ago.
Joe Thornber [Fri, 23 Jan 2015 10:00:07 +0000 (10:00 +0000)]
dm cache: share cache-metadata object across inactive and active DM tables
If a DM table is reloaded with an inactive table when the device is not
suspended (normal procedure for LVM2), then there will be two dm-bufio
objects that can diverge. This can lead to a situation where the
inactive table uses bufio to read metadata at the same time the active
table writes metadata -- resulting in the inactive table having stale
metadata buffers once it is promoted to the active table slot.
Fix this by using reference counting and a global list of cache metadata
objects to ensure there is only one metadata object per metadata device.
Nadav Amit [Thu, 1 Jan 2015 21:11:11 +0000 (23:11 +0200)]
KVM: x86: SYSENTER emulation is broken
SYSENTER emulation is broken in several ways:
1. It misses the case of 16-bit code segments completely (CVE-2015-0239).
2. MSR_IA32_SYSENTER_CS is checked in 64-bit mode incorrectly (bits 0 and 1 can
still be set without causing #GP).
3. MSR_IA32_SYSENTER_EIP and MSR_IA32_SYSENTER_ESP are not masked in
legacy-mode.
4. There is some unneeded code.
Johannes Berg [Fri, 23 Jan 2015 10:10:12 +0000 (11:10 +0100)]
nl80211: fix per-station group key get/del and memory leak
In case userspace attempts to obtain key information for or delete a
unicast key, this is currently erroneously rejected unless the driver
sets the WIPHY_FLAG_IBSS_RSN flag. Apparently enough drivers do so it
was never noticed.
Fix that, and while at it fix a potential memory leak: the error path
in the get_key() function was placed after allocating a message but
didn't free it - move it to a better place. Luckily admin permissions
are needed to call this operation.
Mathy Vanhoef [Tue, 20 Jan 2015 14:05:08 +0000 (15:05 +0100)]
mac80211: properly set CCK flag in radiotap
Fix a regression introduced by commit a5e70697d0c4 ("mac80211: add radiotap flag
and handling for 5/10 MHz") where the IEEE80211_CHAN_CCK channel type flag was
incorrectly replaced by the IEEE80211_CHAN_OFDM flag. This commit fixes that by
using the CCK flag again.
"Fast TSC calibration failed" should not be considered as an error
since other calibration methods are being tried afterward. At most,
those send a warning if they fail (not an error). So let's change
the message from error to warning.
[ tglx: Make if pr_info. It's really not important at all ]
projects / linux.git / log