drm/amd/display: Fix DP MST timeslot issue when fallback happened
[Why]
When USB4 DP link training failed and fell back to lower link rate,
the time slot calculation uses the verified_link_cap.
And the verified_link_cap was not updated to the new one.
It caused the wrong VC payload time-slot was allocated.
[How]
Updated verified_link_cap with the new one from cur_link_settings
after the LT completes successfully.
drm/amd/display: Display distortion after hotplug 5K tiled display
[Why]
During hot plug of specific 5K tiled display, sometimes both the tiles
are not synchronized resulting in distortion. The reason is that otgs of
both the tiles goes out of sync when otg workaround (dcnxxx_disable_otg_wa)
is applied for bandwidth optimization. The otg workaround reenables otg
but otg synchronization context is not reset and hence dc_trigger_sync()
does not resynchronize otg again.
[How]
Implement reset_sync_context_for_pipe() to reset the otg synchronization
context for the disabled pipe and its slave pipes when otg workaround is
applied.
zhikzhai [Fri, 26 Aug 2022 11:44:50 +0000 (19:44 +0800)]
drm/amd/display: skip audio setup when audio stream is enabled
[why]
We have minimal pipe split transition method to avoid pipe
allocation outage.However, this method will invoke audio setup
which cause audio output stuck once pipe reallocate.
[how]
skip audio setup for pipelines which audio stream has been enabled
Hugo Hu [Thu, 1 Sep 2022 02:08:35 +0000 (10:08 +0800)]
drm/amd/display: update gamut remap if plane has changed
[Why]
The desktop plane and full-screen game plane may have different
gamut remap coefficients, if switching between desktop and
full-screen game without updating the gamut remap will cause
incorrect color.
Michael Strauss [Wed, 31 Aug 2022 19:10:43 +0000 (15:10 -0400)]
drm/amd/display: Assume an LTTPR is always present on fixed_vs links
[WHY]
LTTPRs can in very rare instsances fail to increment DPCD LTTPR count.
This results in aux-i LTTPR requests to be sent to the wrong DPCD
address, which causes link training failure.
[HOW]
Override internal repeater count if fixed_vs flag is set for a given link
Leo Li [Tue, 30 Aug 2022 20:38:16 +0000 (16:38 -0400)]
drm/amd/display: Fix double cursor on non-video RGB MPO
[Why]
DC makes use of layer_index (zpos) when picking the HW plane to enable
HW cursor on. However, some compositors will not attach zpos information
to each DRM plane. Consequently, in amdgpu, we default layer_index to 0
and do not update it.
This causes said DC logic to enable HW cursor on all planes of the same
layer_index, which manifests as a double cursor issue if one of the
planes is scaled (and hence scaling the cursor as well).
[How]
Use DRM core helpers to calculate a normalized_zpos value for each
drm_plane_state under each crtc, within the atomic state.
This helper will first consider existing zpos values, and if
identical/unset, fallback to plane ID ordering.
The normalized_zpos is then passed to dc_plane_info during atomic check
for later use by the cursor logic.
Chris Park [Mon, 12 Sep 2022 14:36:49 +0000 (22:36 +0800)]
drm/amd/display: Port DCN30 420 logic to DCN32
[Why]
420 modes are limited by FMT buffer width of 4096
which requires multi-pipe support in form of ODM
combine. If 420 modes have greater HActive than
4096, the DML logic should accomodate whether
it should be rejected, or ODM combine 2:1 or 4:1
is triggered accordingly.
[How]
FMT Buffer limit of 4096 in DCN32. Force ODM
combine depending on HActive and FMT Buffer limit.
Reject modes if TMDS 420 and above 4096.
This patch updates the PTE flags when translate further (TF) is
enabled:
- With translate_further enabled, invalid PTEs can be 0. Reading
consecutive invalid PTEs as 0 is considered a fault. To prevent
this, ensure invalid PTEs have at least 1 bit set.
- The current invalid PTE flags settings to translate a retry fault
into a no-retry fault, doesn't work with TF enabled. As a result,
update invalid PTE flags settings which works for both TF enabled
and disabled case.
Fixes: 352e683b72e79d ("drm/amdgpu: Enable translate_further to extend UTCL2 reach") Reviewed-by: Christian König <[email protected]> Reviewed-by: Felix Kuehling <[email protected]> Signed-off-by: Mukul Joshi <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Tony Krowiak [Tue, 23 Aug 2022 15:06:42 +0000 (11:06 -0400)]
s390/vfio-ap: bypass unnecessary processing of AP resources
It is not necessary to go through the process of validation, linking of
queues to mdev and vice versa and filtering the APQNs assigned to the
matrix mdev to build an AP configuration for a guest if an adapter or
domain being assigned is already assigned to the matrix mdev. Likewise, it
is not necessary to proceed through the process the unassignment of an
adapter, domain or control domain if it is not assigned to the matrix mdev.
Since it is not necessary to process assignment of a resource already
assigned or process unassignment of a resource that is been assigned,
this patch will bypass all assignment/unassignment operations for an
adapter, domain or control domain under these circumstances.
Not only is assignment of a duplicate adapter or domain unnecessary, it
will also cause a hang situation when removing the matrix mdev to which it is
assigned. The reason is because the same vfio_ap_queue objects with an
APQN containing the APID of the adapter or APQI of the domain being
assigned will get added multiple times to the hashtable that holds them.
This results in the pprev and next pointers of the hlist_node (mdev_qnode
field in the vfio_ap_queue object) pointing to the queue object itself
resulting in an interminable loop when the mdev is removed and the queue
table is iterated to reset the queues.
Dan Carpenter [Thu, 15 Sep 2022 11:30:58 +0000 (14:30 +0300)]
i2c: mux: harden i2c_mux_alloc() against integer overflows
A couple years back we went through the kernel an automatically
converted size calculations to use struct_size() instead. The
struct_size() calculation is protected against integer overflows.
However it does not make sense to use the result from struct_size()
for additional math operations as that would negate any safeness.
The i2c-mlxbf.c driver is currently broken because there is a bug
in the calculation of the frequency. core_f, core_r and core_od
are components read from hardware registers and are used to
compute the frequency used to compute different timing parameters.
The shifting mechanism used to get core_f, core_r and core_od is
wrong. Use FIELD_GET to mask and shift the bitfields properly.
tools headers cpufeatures: Sync with the kernel sources
To pick the changes from:
7df548840c496b01 ("x86/bugs: Add "unknown" reporting for MMIO Stale Data")
This only causes these perf files to be rebuilt:
CC /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o
CC /tmp/build/perf/bench/mem-memset-x86-64-asm.o
And addresses this perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
diff -u tools/arch/x86/include/asm/cpufeatures.h arch/x86/include/asm/cpufeatures.h
Adrian Hunter [Thu, 15 Sep 2022 12:26:12 +0000 (15:26 +0300)]
libperf evlist: Fix polling of system-wide events
Originally, (refer commit f90d194a867a5a1d ("perf evlist: Do not poll
events that use the system_wide flag") there wasn't much reason to poll
system-wide events because:
1. The mmaps get "merged" via set-output anyway (the per-cpu case)
2. perf reads all mmaps when any event is woken
3. system-wide mmaps do not fill up as fast as the mmaps for user
selected events
But there was 1 reason not to poll which was that it prevented correct
termination due to POLLHUP on all user selected events. That issue is
now easily resolved by using fdarray_flag__nonfilterable.
With the advent of commit ae4f8ae16a078964 ("libperf evlist: Allow
mixing per-thread and per-cpu mmaps"), system-wide mmaps can be used
also in the per-thread case where reason 1 does not apply.
Fix the omission of system-wide events from polling by using the
fdarray_flag__nonfilterable flag.
Adrian Hunter [Thu, 15 Sep 2022 12:26:11 +0000 (15:26 +0300)]
perf record: Fix cpu mask bit setting for mixed mmaps
With mixed per-thread and (system-wide) per-cpu maps, the "any cpu" value
-1 must be skipped when setting CPU mask bits.
Prior to commit cbd7bfc7fd99acdd ("tools/perf: Fix out of bound access
to cpu mask array") the invalid setting went unnoticed, but since then
it causes perf record to fail with an error.
Example:
Before:
$ perf record -e intel_pt// --per-thread uname
Failed to initialize parallel data streaming masks
After:
$ perf record -e intel_pt// --per-thread uname
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.068 MB perf.data ]
* tag 'opp-fixes-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
dt-bindings: opp: Add missing (unevaluated|additional)Properties on child nodes
OPP: Fix an un-initialized variable usage
Merge tag 'for-linus-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux
Pull UML fixes from Richard Weinberger:
- Various fixes for build warnings
- Fix default kernel command line
* tag 'for-linus-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux:
arch: um: Mark the stack non-executable to fix a binutils warning
um: Prevent KASAN splats in dump_stack()
um: fix default console kernel parameter
um: Cleanup compiler warning in arch/x86/um/tls_32.c
um: Cleanup syscall_handler_t cast in syscalls_32.h
Merge tag 'mips-fixes_6.0_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fix missing export for Lantiq watchdog driver
- fix ethernet phy interface setup for Loongson32
* tag 'mips-fixes_6.0_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Loongson32: Fix PHY-mode being left unspecified
MIPS: lantiq: export clk_get_io() for lantiq_wdt.ko
* tag 'dmaengine-fix-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: zynqmp_dma: Typecast with enum to fix the coverity warning
dmaengine: ti: k3-udma-private: Fix refcount leak bug in of_xudma_dev_get()
dmaengine: xilinx_dma: Report error in case of dma_set_mask_and_coherent API failure
dmaengine: xilinx_dma: cleanup for fetching xlnx,num-fstores property
dmaengine: xilinx_dma: Fix devm_platform_ioremap_resource error handling
Merge tag 'iommu-fixes-v6.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Two fixes for Intel VT-d:
- Check the right capability bit for 5-level page table support.
- Revert a previous fix which caused a regression with Thunderbolt
devices"
* tag 'iommu-fixes-v6.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Check correct capability for sagaw determination
Revert "iommu/vt-d: Fix possible recursive locking in intel_iommu_init()"
Merge tag 'sound-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bit more changes than wished, but still manageable amount.
Most of commits are HD-audio specific device fixes / quirks, while
there is a revert for the previous fix due to regressions and a
double-free fix in ALSA core code"
* tag 'sound-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: usb-audio: Split endpoint setups for hw_params and prepare"
ALSA: core: Fix double-free at snd_card_new()
ALSA: hda/realtek: Add a quirk for HP OMEN 16 (8902) mute LED
ALSA: hda/hdmi: Fix the converter reuse for the silent stream
ALSA: hda/realtek: Add quirk for ASUS GA503R laptop
ALSA: hda/realtek: Add pincfg for ASUS G533Z HP jack
ALSA: hda/realtek: Add pincfg for ASUS G513 HP jack
ALSA: hda/realtek: Re-arrange quirk table entries
ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5530 laptop
ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5570 laptop
ALSA: hda: Fix Nvidia dp infoframe
ALSA: hda/realtek: Add quirk for Huawei WRT-WX9
ALSA: hda/tegra: set depop delay for tegra
ALSA: hda: add Intel 5 Series / 3400 PCI DID
ALSA: hda: Fix hang at HD-audio codec unbinding due to refcount saturation
Matthew Rosato [Tue, 20 Sep 2022 19:30:25 +0000 (15:30 -0400)]
KVM: s390: pci: register pci hooks without interpretation
The kvm registration hooks must be registered even if the facilities
necessary for zPCI interpretation are unavailable, as vfio-pci-zdev will
expect to use the hooks regardless.
This fixes an issue where vfio-pci-zdev will fail its open function
because of a missing kvm_register when running on hardware that does not
support zPCI interpretation.
Matthew Rosato [Wed, 7 Sep 2022 15:59:52 +0000 (11:59 -0400)]
KVM: s390: pci: fix GAIT physical vs virtual pointers usage
The GAIT and all of its entries must be represented by physical
addresses as this structure is shared with underlying firmware.
We can keep a virtual address of the GAIT origin in order to
handle processing in the kernel, but when traversing the entries
we must again convert the physical AISB stored in that GAIT entry
into a virtual address in order to process it.
Note: this currently doesn't fix a real bug, since virtual addresses
are indentical to physical ones.
This silences smatch warnings reported by kbuild bot:
arch/s390/kvm/gaccess.c:859 guest_range_to_gpas() error: uninitialized symbol 'prot'.
arch/s390/kvm/gaccess.c:1064 access_guest_with_key() error: uninitialized symbol 'prot'.
This is because it cannot tell that the value is not used in this case.
The trans_exc* only examine prot if code is PGM_PROTECTION.
Pass a dummy value for other codes.
Jakub Kicinski [Wed, 21 Sep 2022 13:52:32 +0000 (06:52 -0700)]
Merge tag 'linux-can-fixes-for-6.0-20220921' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-09-21
The 1st patch is by me, targets the flexcan driver and fixes a
potential system hang on single core systems under high CAN packet
rate.
The next 2 patches are also by me and target the gs_usb driver. A
potential race condition during the ndo_open callback as well as the
return value if the ethtool identify feature is not supported are
fixed.
* tag 'linux-can-fixes-for-6.0-20220921' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: gs_usb: gs_usb_set_phys_id(): return with error if identify is not supported
can: gs_usb: gs_can_open(): fix race dev->can.state condition
can: flexcan: flexcan_mailbox_read() fix return value for drop = true
====================
Namhyung Kim [Fri, 16 Sep 2022 18:41:32 +0000 (11:41 -0700)]
perf test: Add a new test for perf stat cgroup BPF counter
$ sudo ./perf test -v each-cgroup
96: perf stat --bpf-counters --for-each-cgroup test :
--- start ---
test child forked, pid 79600
test child finished with 0
---- end ----
perf stat --bpf-counters --for-each-cgroup test: Ok
Namhyung Kim [Fri, 16 Sep 2022 18:41:31 +0000 (11:41 -0700)]
perf stat: Use evsel->core.cpus to iterate cpus in BPF cgroup counters
If it mixes core and uncore events, each evsel would have different cpu map.
But it assumed they are same with evlist's all_cpus and accessed by the same
index. This resulted in a crash like below.
$ perf stat -a --bpf-counters --for-each_cgroup ^. -e cycles,imc/cas_count_read/ sleep 1
Segmentation fault
While it's not recommended to use uncore events for cgroup aggregation, it
should not crash.
Namhyung Kim [Fri, 16 Sep 2022 18:41:29 +0000 (11:41 -0700)]
perf stat: Fix BPF program section name
It seems the recent libbpf got more strict about the section name.
I'm seeing a failure like this:
$ sudo ./perf stat -a --bpf-counters --for-each-cgroup ^. sleep 1
libbpf: prog 'on_cgrp_switch': missing BPF prog type, check ELF section name 'perf_events'
libbpf: prog 'on_cgrp_switch': failed to load: -22
libbpf: failed to load object 'bperf_cgroup_bpf'
libbpf: failed to load BPF skeleton 'bperf_cgroup_bpf': -22
Failed to load cgroup skeleton
The section name should be 'perf_event' (without the trailing 's').
Although it's related to the libbpf change, it'd be better fix the
section name in the first place.
Merge tag 'fpga-for-6.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into char-misc-linus
Xu writes:
FPGA Manager changes for 6.0-final
Intel m10 bmc secure update
- Russ's change fixes the memory leak for a sysfs node reading
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-6.0 branch).
Signed-off-by: Xu Yilun <[email protected]>
* tag 'fpga-for-6.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
fpga: m10bmc-sec: Fix possible memory leak of flash_buf
Jianglei Nie [Wed, 14 Sep 2022 01:42:38 +0000 (09:42 +0800)]
net: atlantic: fix potential memory leak in aq_ndev_close()
If aq_nic_stop() fails, aq_ndev_close() returns err without calling
aq_nic_deinit() to release the relevant memory and resource, which
will lead to a memory leak.
We can fix it by deleting the if condition judgment and goto statement to
call aq_nic_deinit() directly after aq_nic_stop() to fix the memory leak.
The following set contains netfilter fixes for the *net* tree.
Regressions (rc only):
recent ebtables crash fix was incomplete, it added a memory leak.
The patch to fix possible buffer overrun for BIG TCP in ftp conntrack
tried to be too clever, we cannot re-use ct->lock: NAT engine might
grab it again -> deadlock. Revert back to a global spinlock.
Both from myself.
Remove the documentation for the recently removed
'nf_conntrack_helper' sysctl as well, from Pablo Neira.
The static_branch_inc() that guards the 'chain stats enabled' path
needs to be deferred further, until the entire transaction was created.
From Tetsuo Handa.
Older bugs:
Since 5.3:
nf_tables_addchain may leak pcpu memory in error path when
offloading fails. Also from Tetsuo Handa.
====================
can: gs_usb: gs_usb_set_phys_id(): return with error if identify is not supported
Until commit 409c188c57cd ("can: tree-wide: advertise software
timestamping capabilities") the ethtool_ops was only assigned for
devices which support the GS_CAN_FEATURE_IDENTIFY feature. That commit
assigns ethtool_ops unconditionally.
This results on controllers without GS_CAN_FEATURE_IDENTIFY support
for the following ethtool error:
The dev->can.state is set to CAN_STATE_ERROR_ACTIVE, after the device
has been started. On busy networks the CAN controller might receive
CAN frame between and go into an error state before the dev->can.state
is assigned.
Assign dev->can.state before starting the controller to close the race
window.
can: flexcan: flexcan_mailbox_read() fix return value for drop = true
The following happened on an i.MX25 using flexcan with many packets on
the bus:
The rx-offload queue reached a length more than skb_queue_len_max. In
can_rx_offload_offload_one() the drop variable was set to true which
made the call to .mailbox_read() (here: flexcan_mailbox_read()) to
_always_ return ERR_PTR(-ENOBUFS) and drop the rx'ed CAN frame. So
can_rx_offload_offload_one() returned ERR_PTR(-ENOBUFS), too.
can_rx_offload_irq_offload_fifo() looks as follows:
| while (1) {
| skb = can_rx_offload_offload_one(offload, 0);
| if (IS_ERR(skb))
| continue;
| if (!skb)
| break;
| ...
| }
The flexcan driver wrongly always returns ERR_PTR(-ENOBUFS) if drop is
requested, even if there is no CAN frame pending. As the i.MX25 is a
single core CPU, while the rx-offload processing is active, there is
no thread to process packets from the offload queue. So the queue
doesn't get any shorter and this results is a tight loop.
Instead of always returning ERR_PTR(-ENOBUFS) if drop is requested,
return NULL if no CAN frame is pending.
Changes since v1: https://lore.kernel.org/all/20220810144536[email protected]
- don't break in can_rx_offload_irq_offload_fifo() in case of an error,
return NULL in flexcan_mailbox_read() in case of no pending CAN frame
instead
Meng Li [Wed, 21 Sep 2022 03:20:20 +0000 (11:20 +0800)]
gpiolib: cdev: Set lineevent_state::irq after IRQ register successfully
When running gpio test on nxp-ls1028 platform with below command
gpiomon --num-events=3 --rising-edge gpiochip1 25
There will be a warning trace as below:
Call trace:
free_irq+0x204/0x360
lineevent_free+0x64/0x70
gpio_ioctl+0x598/0x6a0
__arm64_sys_ioctl+0xb4/0x100
invoke_syscall+0x5c/0x130
......
el0t_64_sync+0x1a0/0x1a4
The reason of this issue is that calling request_threaded_irq()
function failed, and then lineevent_free() is invoked to release
the resource. Since the lineevent_state::irq was already set, so
the subsequent invocation of free_irq() would trigger the above
warning call trace. To fix this issue, set the lineevent_state::irq
after the IRQ register successfully.
David Gow [Wed, 21 Sep 2022 06:48:55 +0000 (14:48 +0800)]
arch: um: Mark the stack non-executable to fix a binutils warning
Since binutils 2.39, ld will print a warning if any stack section is
executable, which is the default for stack sections on files without a
.note.GNU-stack section.
This was fixed for x86 in commit ffcf9c5700e4 ("x86: link vdso and boot with -z noexecstack --no-warn-rwx-segments"),
but remained broken for UML, resulting in several warnings:
/usr/bin/ld: warning: arch/x86/um/vdso/vdso.o: missing .note.GNU-stack section implies executable stack
/usr/bin/ld: NOTE: This behaviour is deprecated and will be removed in a future version of the linker
/usr/bin/ld: warning: .tmp_vmlinux.kallsyms1 has a LOAD segment with RWX permissions
/usr/bin/ld: warning: .tmp_vmlinux.kallsyms1.o: missing .note.GNU-stack section implies executable stack
/usr/bin/ld: NOTE: This behaviour is deprecated and will be removed in a future version of the linker
/usr/bin/ld: warning: .tmp_vmlinux.kallsyms2 has a LOAD segment with RWX permissions
/usr/bin/ld: warning: .tmp_vmlinux.kallsyms2.o: missing .note.GNU-stack section implies executable stack
/usr/bin/ld: NOTE: This behaviour is deprecated and will be removed in a future version of the linker
/usr/bin/ld: warning: vmlinux has a LOAD segment with RWX permissions
Link both the VDSO and vmlinux with -z noexecstack, fixing the warnings
about .note.GNU-stack sections. In addition, pass --no-warn-rwx-segments
to dodge the remaining warnings about LOAD segments with RWX permissions
in the kallsyms objects. (Note that this flag is apparently not
available on lld, so hide it behind a test for BFD, which is what the
x86 patch does.)
net: sh_eth: Fix PHY state warning splat during system resume
Since commit 744d23c71af39c7d ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 626 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xe4
As the Renesas SuperH Ethernet driver already calls phy_{stop,start}()
in its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
net: ravb: Fix PHY state warning splat during system resume
Since commit 744d23c71af39c7d ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 1197 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xc8
As the Renesas Ethernet AVB driver already calls phy_{stop,start}() in
its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
netfilter: ebtables: fix memory leak when blob is malformed
The bug fix was incomplete, it "replaced" crash with a memory leak.
The old code had an assignment to "ret" embedded into the conditional,
restore this.
Fixes: 7997eff82828 ("netfilter: ebtables: reject blobs that don't provide all entry points") Reported-and-tested-by: [email protected] Signed-off-by: Florian Westphal <[email protected]>
netfilter: nf_tables: fix percpu memory leak at nf_tables_addchain()
It seems to me that percpu memory for chain stats started leaking since
commit 3bc158f8d0330f0a ("netfilter: nf_tables: map basechain priority to
hardware priority") when nft_chain_offload_priority() returned an error.
netfilter: nf_tables: fix nft_counters_enabled underflow at nf_tables_addchain()
syzbot is reporting underflow of nft_counters_enabled counter at
nf_tables_addchain() [1], for commit 43eb8949cfdffa76 ("netfilter:
nf_tables: do not leave chain stats enabled on error") missed that
nf_tables_chain_destroy() after nft_basechain_init() in the error path of
nf_tables_addchain() decrements the counter because nft_basechain_init()
makes nft_is_base_chain() return true by setting NFT_CHAIN_BASE flag.
Increment the counter immediately after returning from
nft_basechain_init().
ice: Fix interface being down after reset with link-down-on-close flag on
When performing a reset on ice driver with link-down-on-close flag on
interface would always stay down. Fix this by moving a check of this
flag to ice_stop() that is called only when user wants to bring
interface down.
Fixes: ab4ab73fc1ec ("ice: Add ethtool private flag to make forcing link down optional") Signed-off-by: Mateusz Palczewski <[email protected]> Tested-by: Petr Oros <[email protected]> Tested-by: Gurucharan <[email protected]> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <[email protected]>
ice: config netdev tc before setting queues number
After lowering number of tx queues the warning appears:
"Number of in use tx queues changed invalidating tc mappings. Priority
traffic classification disabled!"
Example command to reproduce:
ethtool -L enp24s0f0 tx 36 rx 36
Fix this by setting correct tc mapping before setting real number of
queues on netdev.
Fixes: 0754d65bd4be5 ("ice: Add infrastructure for mqprio support via ndo_setup_tc") Signed-off-by: Michal Swiatkowski <[email protected]> Tested-by: Gurucharan <[email protected]> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <[email protected]>
Jakub Kicinski [Tue, 20 Sep 2022 18:41:17 +0000 (11:41 -0700)]
Merge branch 'fixes-for-tc-taprio-software-mode'
Vladimir Oltean says:
====================
Fixes for tc-taprio software mode
While working on some new features for tc-taprio, I found some strange
behavior which looked like bugs. I was able to eventually trigger a NULL
pointer dereference. This patch set fixes 2 issues I saw. Detailed
explanation in patches.
====================
This is because tc_modify_qdisc() behaves differently when mqprio is
root, vs when taprio is root.
In the mqprio case, it finds the parent qdisc through
p = qdisc_lookup(dev, TC_H_MAJ(clid)), and then the child qdisc through
q = qdisc_leaf(p, clid). This leaf qdisc q has handle 0, so it is
ignored according to the comment right below ("It may be default qdisc,
ignore it"). As a result, tc_modify_qdisc() goes through the
qdisc_create() code path, and this gives taprio_init() a chance to check
for sch_parent != TC_H_ROOT and error out.
Whereas in the taprio case, the returned q = qdisc_leaf(p, clid) is
different. It is not the default qdisc created for each netdev queue
(both taprio and mqprio call qdisc_create_dflt() and keep them in
a private q->qdiscs[], or priv->qdiscs[], respectively). Instead, taprio
makes qdisc_leaf() return the _root_ qdisc, aka itself.
When taprio does that, tc_modify_qdisc() goes through the qdisc_change()
code path, because the qdisc layer never finds out about the child qdisc
of the root. And through the ->change() ops, taprio has no reason to
check whether its parent is root or not, just through ->init(), which is
not called.
The problem is the taprio_leaf() implementation. Even though code wise,
it does the exact same thing as mqprio_leaf() which it is copied from,
it works with different input data. This is because mqprio does not
attach itself (the root) to each device TX queue, but one of the default
qdiscs from its private array.
In fact, since commit 13511704f8d7 ("net: taprio offload: enforce qdisc
to netdev queue mapping"), taprio does this too, but just for the full
offload case. So if we tried to attach a taprio child to a fully
offloaded taprio root qdisc, it would properly fail too; just not to a
software root taprio.
To fix the problem, stop looking at the Qdisc that's attached to the TX
queue, and instead, always return the default qdiscs that we've
allocated (and to which we privately enqueue and dequeue, in software
scheduling mode).
Since Qdisc_class_ops :: leaf is only called from tc_modify_qdisc(),
the risk of unforeseen side effects introduced by this change is
minimal.
Fixes: 5a781ccbd19e ("tc: Add support for configuring the taprio scheduler") Signed-off-by: Vladimir Oltean <[email protected]> Reviewed-by: Vinicius Costa Gomes <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Vladimir Oltean [Thu, 15 Sep 2022 10:08:01 +0000 (13:08 +0300)]
net/sched: taprio: avoid disabling offload when it was never enabled
In an incredibly strange API design decision, qdisc->destroy() gets
called even if qdisc->init() never succeeded, not exclusively since
commit 87b60cfacf9f ("net_sched: fix error recovery at qdisc creation"),
but apparently also earlier (in the case of qdisc_create_dflt()).
The taprio qdisc does not fully acknowledge this when it attempts full
offload, because it starts off with q->flags = TAPRIO_FLAGS_INVALID in
taprio_init(), then it replaces q->flags with TCA_TAPRIO_ATTR_FLAGS
parsed from netlink (in taprio_change(), tail called from taprio_init()).
But in taprio_destroy(), we call taprio_disable_offload(), and this
determines what to do based on FULL_OFFLOAD_IS_ENABLED(q->flags).
But looking at the implementation of FULL_OFFLOAD_IS_ENABLED()
(a bitwise check of bit 1 in q->flags), it is invalid to call this macro
on q->flags when it contains TAPRIO_FLAGS_INVALID, because that is set
to U32_MAX, and therefore FULL_OFFLOAD_IS_ENABLED() will return true on
an invalid set of flags.
As a result, it is possible to crash the kernel if user space forces an
error between setting q->flags = TAPRIO_FLAGS_INVALID, and the calling
of taprio_enable_offload(). This is because drivers do not expect the
offload to be disabled when it was never enabled.
The error that we force here is to attach taprio as a non-root qdisc,
but instead as child of an mqprio root qdisc:
Fixes: 9c66d1564676 ("taprio: Add support for hardware offloading") Signed-off-by: Vladimir Oltean <[email protected]> Reviewed-by: Vinicius Costa Gomes <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
ipv6: Fix crash when IPv6 is administratively disabled
The global 'raw_v6_hashinfo' variable can be accessed even when IPv6 is
administratively disabled via the 'ipv6.disable=1' kernel command line
option, leading to a crash [1].
Fix by restoring the original behavior and always initializing the
variable, regardless of IPv6 support being administratively disabled or
not.
Vladimir Oltean [Fri, 16 Sep 2022 13:32:09 +0000 (16:32 +0300)]
net: enetc: deny offload of tc-based TSN features on VF interfaces
TSN features on the ENETC (taprio, cbs, gate, police) are configured
through a mix of command BD ring messages and port registers:
enetc_port_rd(), enetc_port_wr().
Port registers are a region of the ENETC memory map which are only
accessible from the PCIe Physical Function. They are not accessible from
the Virtual Functions.
Moreover, attempting to access these registers crashes the kernel:
$ echo 1 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs
pci 0000:00:01.0: [1957:ef00] type 00 class 0x020001
fsl_enetc_vf 0000:00:01.0: Adding to iommu group 15
fsl_enetc_vf 0000:00:01.0: enabling device (0000 -> 0002)
fsl_enetc_vf 0000:00:01.0 eno0vf0: renamed from eth0
$ tc qdisc replace dev eno0vf0 root taprio num_tc 8 map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 base-time 0 \
sched-entry S 0x7f 900000 sched-entry S 0x80 100000 flags 0x2
Unable to handle kernel paging request at virtual address ffff800009551a08
Internal error: Oops: 96000007 [#1] PREEMPT SMP
pc : enetc_setup_tc_taprio+0x170/0x47c
lr : enetc_setup_tc_taprio+0x16c/0x47c
Call trace:
enetc_setup_tc_taprio+0x170/0x47c
enetc_setup_tc+0x38/0x2dc
taprio_change+0x43c/0x970
taprio_init+0x188/0x1e0
qdisc_create+0x114/0x470
tc_modify_qdisc+0x1fc/0x6c0
rtnetlink_rcv_msg+0x12c/0x390
Split enetc_setup_tc() into separate functions for the PF and for the
VF drivers. Also remove enetc_qos.o from being included into
enetc-vf.ko, since it serves absolutely no purpose there.
Vladimir Oltean [Fri, 16 Sep 2022 13:32:08 +0000 (16:32 +0300)]
net: enetc: move enetc_set_psfp() out of the common enetc_set_features()
The VF netdev driver shouldn't respond to changes in the NETIF_F_HW_TC
flag; only PFs should. Moreover, TSN-specific code should go to
enetc_qos.c, which should not be included in the VF driver.
Jakub Kicinski [Tue, 20 Sep 2022 18:26:18 +0000 (11:26 -0700)]
Merge branch 'wireguard-patches-for-6-0-rc6'
Jason A. Donenfeld says:
====================
wireguard patches for 6.0-rc6
1) The ratelimiter timing test doesn't help outside of development, yet
it is currently preventing the module from being inserted on some
kernels when it flakes at insertion time. So we disable it.
2) A fix for a build error on UML, caused by a recent change in a
different tree.
3) A WARN_ON() is triggered by Kees' new fortified memcpy() patch, due
to memcpy()ing over a sockaddr pointer with the size of a
sockaddr_in[6]. The type safe fix is pretty simple. Given how classic
of a thing sockaddr punning is, I suspect this may be the first in a
few patches like this throughout the net tree, once Kees' fortify
series is more widely deployed (current it's just in next).
====================
wireguard: netlink: avoid variable-sized memcpy on sockaddr
Doing a variable-sized memcpy is slower, and the compiler isn't smart
enough to turn this into a constant-size assignment.
Further, Kees' latest fortified memcpy will actually bark, because the
destination pointer is type sockaddr, not explicitly sockaddr_in or
sockaddr_in6, so it thinks there's an overflow:
memcpy: detected field-spanning write (size 28) of single field
"&endpoint.addr" at drivers/net/wireguard/netlink.c:446 (size 16)
Fix this by just assigning by using explicit casts for each checked
case.
wireguard: selftests: do not install headers on UML
Since 1b620d539ccc ("kbuild: disable header exports for UML in a
straightforward way"), installing headers fails on UML, so just disable
installing them, since they're not needed anyway on the architecture.
Fixes: b438b3b8d6e6 ("wireguard: selftests: support UML") Signed-off-by: Jason A. Donenfeld <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
wireguard: ratelimiter: disable timings test by default
A previous commit tried to make the ratelimiter timings test more
reliable but in the process made it less reliable on other
configurations. This is an impossible problem to solve without
increasingly ridiculous heuristics. And it's not even a problem that
actually needs to be solved in any comprehensive way, since this is only
ever used during development. So just cordon this off with a DEBUG_
ifdef, just like we do for the trie's randomized tests, so it can be
enabled while hacking on the code, and otherwise disabled in CI. In the
process we also revert 151c8e499f47.
Fixes: 151c8e499f47 ("wireguard: ratelimiter: use hrtimer in selftest") Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Merge tag 'for-6.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- two fixes for hangs in the umount sequence where threads depend on
each other and the work must be finished in the right order
- in zoned mode, wait for flushing all block group metadata IO before
finishing the zone
* tag 'for-6.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: wait for extent buffer IOs before finishing a zone
btrfs: fix hang during unmount when stopping a space reclaim worker
btrfs: fix hang during unmount when stopping block group reclaim worker
Merge tag 'fs.fixes.v6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping
Pull vfs fix from Christian Brauner:
"Beginning of the merge window we introduced the vfs{g,u}id_t types in b27c82e12965 ("attr: port attribute changes to new types") and changed
various codepaths over including chown_common().
When userspace passes -1 for an ownership change the ownership fields
in struct iattr stay uninitialized. Usually this is fine because any
code making use of any fields in struct iattr must check the
->ia_valid field whether the value of interest has been initialized.
That's true for all struct iattr passing code.
However, over the course of the last year with more heavy use of KMSAN
we found quite a few places that got this wrong. A recent one I fixed
was 3cb6ee991496 ("9p: only copy valid iattrs in 9P2000.L setattr
implementation").
But we also have LSM hooks. Actually we have two. The first one is
security_inode_setattr() in notify_change() which does the right thing
and passes the full struct iattr down to LSMs and thus LSMs can check
whether it is initialized.
But then we also have security_path_chown() which passes down a path
argument and the target ownership as the filesystem would see it. For
the latter we now generate the target values based on struct iattr and
pass it down. However, when userspace passes -1 then struct iattr
isn't initialized.
This patch simply initializes ->ia_vfs{g,u}id with INVALID_VFS{G,U}ID
so the hook continue to see invalid ownership when -1 is passed from
userspace. The only LSM that cares about the actual values is Tomoyo.
The vfs codepaths don't look at these fields without ->ia_valid being
set so there's no harm in initializing ->ia_vfs{g,u}id. Arguably this
is also safer since we can't end up copying valid ownership values
when invalid ownership values should be passed.
This only affects mainline. No kernel has been released with this and
thus no backport is needed. The commit is thus marked with a Fixes:
tag but annotated with "# mainline only" (I didn't quite remember what
Greg said about how to tell stable autoselect to not bother with fixes
for mainline only)"
* tag 'fs.fixes.v6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping:
open: always initialize ownership fields
There is a single kmalloc in this driver, and it's not currently
guarded against allocation failure. Do it here by just bailing-out
the reboot handler, in case this tentative allocation fails.
Fixes: 416581e48679 ("efi: efibc: avoid efivar API for setting variables") Signed-off-by: Guilherme G. Piccoli <[email protected]> Signed-off-by: Ard Biesheuvel <[email protected]>
Merge tag 'execve-v6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull execve reverts from Kees Cook:
"The recent work to support time namespace unsharing turns out to have
some undesirable corner cases, so rather than allowing the API to stay
exposed for another release, it'd be best to remove it ASAP, with the
replacement getting another cycle of testing. Nothing is known to use
this yet, so no userspace breakage is expected.
- Remove the recent 'unshare time namespace on vfork+exec' feature
(Andrei Vagin)"
* tag 'execve-v6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
Revert "fs/exec: allow to unshare a time namespace on vfork+exec"
Revert "selftests/timens: add a test for vfork+exit"
syzbot is still complaining uninit-value in tcp_recvmsg(), for
commit 1228b34c8d0ecf6d ("net: clear msg_get_inq in __sys_recvfrom() and
__copy_msghdr_from_user()") missed that __get_compat_msghdr() is called
instead of copy_msghdr_from_user() when MSG_CMSG_COMPAT is specified.
ipmr: Always call ip{,6}_mr_forward() from RCU read-side critical section
These functions expect to be called from RCU read-side critical section,
but this only happens when invoked from the data path via
ip{,6}_mr_input(). They can also be invoked from process context in
response to user space adding a multicast route which resolves a cache
entry with queued packets [1][2].
Fix by adding missing rcu_read_lock() / rcu_read_unlock() in these call
paths.
Alex Elder [Tue, 13 Sep 2022 20:46:02 +0000 (15:46 -0500)]
net: ipa: properly limit modem routing table use
IPA can route packets between IPA-connected entities. The AP and
modem are currently the only such entities supported, and no routing
is required to transfer packets between them.
The number of entries in each routing table is fixed, and defined at
initialization time. Some of these entries are designated for use
by the modem, and the rest are available for the AP to use. The AP
sends a QMI message to the modem which describes (among other
things) information about routing table memory available for the
modem to use.
Currently the QMI initialization packet gives wrong information in
its description of routing tables. What *should* be supplied is the
maximum index that the modem can use for the routing table memory
located at a given location. The current code instead supplies the
total *number* of routing table entries. Furthermore, the modem is
granted the entire table, not just the subset it's supposed to use.
This patch fixes this. First, the ipa_mem_bounds structure is
generalized so its "end" field can be interpreted either as a final
byte offset, or a final array index. Second, the IPv4 and IPv6
(non-hashed and hashed) table information fields in the QMI
ipa_init_modem_driver_req structure are changed to be ipa_mem_bounds
rather than ipa_mem_array structures. Third, we set the "end" value
for each routing table to be the last index, rather than setting the
"count" to be the number of indices. Finally, instead of allowing
the modem to use all of a routing table's memory, it is limited to
just the portion meant to be used by the modem. In all versions of
IPA currently supported, that is IPA_ROUTE_MODEM_COUNT (8) entries.
Chris Wilson [Fri, 16 Sep 2022 09:24:03 +0000 (11:24 +0200)]
drm/i915/gem: Really move i915_gem_context.link under ref protection
i915_perf assumes that it can use the i915_gem_context reference to
protect its i915->gem.contexts.list iteration. However, this requires
that we do not remove the context from the list until after we drop the
final reference and release the struct. If, as currently, we remove the
context from the list during context_close(), the link.next pointer may
be poisoned while we are holding the context reference and cause a GPF:
v3: fix incorrect syntax of spin_lock() replacing spin_lock_irqsave()
v2: irqsave not required in a worker, neither conversion to irq safe
elsewhere (Tvrtko),
- perf: it's safe to call gen8_configure_context() even if context has
been closed, no need to check,
- drop unrelated cleanup (Andi, Tvrtko)
Due to i915_perf assuming that it can use the i915_gem_context reference
to protect its i915->gem.contexts.list iteration, we need to defer removal
of the context from the list until last reference to the context is put.
However, there is a risk of triggering kernel warning on contexts list not
empty at driver release time if we deleagate that task to a worker for
i915_gem_context_release_work(), unless that work is flushed first.
Unfortunately, it is not flushed on driver release. Fix it.
Instead of additionally calling flush_workqueue(), either directly or via
a new dedicated wrapper around it, replace last call to
i915_gem_drain_freed_objects() with existing i915_gem_drain_workqueue()
that performs both tasks.
Dusty Mabe reported consistent hang during CoreOS shutdown with a MD
RAID1 setup. Although apparently similar hangs happened before,
and this patch most likely is not the root cause it made it much
more severe. Revert it until we can figure out what is going on
with the md driver.
gpio: mockup: fix NULL pointer dereference when removing debugfs
We now remove the device's debugfs entries when unbinding the driver.
This now causes a NULL-pointer dereference on module exit because the
platform devices are unregistered *after* the global debugfs directory
has been recursively removed. Fix it by unregistering the devices first.
Cong Wang [Mon, 12 Sep 2022 17:35:53 +0000 (10:35 -0700)]
tcp: read multiple skbs in tcp_read_skb()
Before we switched to ->read_skb(), ->read_sock() was passed with
desc.count=1, which technically indicates we only read one skb per
->sk_data_ready() call. However, for TCP, this is not true.
TCP at least has sk_rcvlowat which intentionally holds skb's in
receive queue until this watermark is reached. This means when
->sk_data_ready() is invoked there could be multiple skb's in the
queue, therefore we have to read multiple skbs in tcp_read_skb()
instead of one.
net: dsa: microchip: lan937x: fix maximum frame length check
Maximum frame length check is enabled in lan937x switch on POR, But it
is found to be disabled on driver during port setup operation. Due to
this, packets are not dropped when transmitted with greater than configured
value. For testing, setup made for lan1->lan2 transmission and configured
lan1 interface with a frame length (less than 1500 as mentioned in
documentation) and transmitted packets with greater than configured value.
Expected no packets at lan2 end, but packets observed at lan2.
Based on the documentation, packets should get discarded if the actual
packet length doesn't match the frame length configured. Frame length check
should be disabled only for cascaded ports due to tailtags.
This feature was disabled on ksz9477 series due to ptp issue, which is
not in lan937x series. But since lan937x took ksz9477 as base, frame
length check disabled here as well. Patch added to remove this portion
from port setup so that maximum frame length check will be active for
normal ports.
Beginning of the merge window we introduced the vfs{g,u}id_t types in b27c82e12965 ("attr: port attribute changes to new types") and changed
various codepaths over including chown_common().
During that change we forgot to account for the case were the passed
ownership value is -1. In this case the ownership fields in struct iattr
aren't initialized but we rely on them being initialized by the time we
generate the ownership to pass down to the LSMs. All the major LSMs
don't care about the ownership values at all. Only Tomoyo uses them and
so it took a while for syzbot to unearth this issue.
Fix this by initializing the ownership fields and do it within the
retry_deleg block. While notify_change() doesn't alter the ownership
fields currently we shouldn't rely on it.
Since no kernel has been released with these changes this does not
needed to be backported to any stable kernels.
Randy Dunlap [Tue, 31 May 2022 02:55:57 +0000 (19:55 -0700)]
drm/hisilicon: Add depends on MMU
The Kconfig symbol depended on MMU but was dropped by the commit acad3fe650a5 ("drm/hisilicon: Removed the dependency on the mmu")
because it already had as a dependency ARM64 that already selects MMU.
But later, commit a0f25a6bb319 ("drm/hisilicon/hibmc: Allow to be built
if COMPILE_TEST is enabled") allowed the driver to be built for non-ARM64
when COMPILE_TEST is set but that could lead to unmet direct dependencies
and linking errors.
Prevent a kconfig warning when MMU is not enabled by making
DRM_HISI_HIBMC depend on MMU.
projects / linux.git / log