Paolo Abeni [Fri, 23 Feb 2024 16:14:14 +0000 (17:14 +0100)]
mptcp: push at DSS boundaries
when inserting not contiguous data in the subflow write queue,
the protocol creates a new skb and prevent the TCP stack from
merging it later with already queued skbs by setting the EOR marker.
Still no push flag is explicitly set at the end of previous GSO
packet, making the aggregation on the receiver side sub-optimal -
and packetdrill self-tests less predictable.
Explicitly mark the end of not contiguous DSS with the push flag.
After the 'Fixes' commit mentioned below, the client side might print
the following warning once when a subflow is fully established at the
reception of any valid additional ack:
MPTCP: bogus mpc option on established client sk
That's a normal situation, and no warning should be printed for that. We
can then skip the check when the label is used.
Geliang Tang [Fri, 23 Feb 2024 16:14:12 +0000 (17:14 +0100)]
selftests: mptcp: rm subflow with v4/v4mapped addr
Now both a v4 address and a v4-mapped address are supported when
destroying a userspace pm subflow, this patch adds a second subflow
to "userspace pm add & remove address" test, and two subflows could
be removed two different ways, one with the v4mapped and one with v4.
That's because on the server side, the family is set to AF_INET6 and the
v4 address is mapped in a v6 one.
This patch fixes this issue. In mptcp_pm_nl_subflow_destroy_doit(), before
checking local address family with remote address family, map an IPv4
address to an IPv6 address if the pair is a v4-mapped address.
Oleksij Rempel [Thu, 22 Feb 2024 12:38:38 +0000 (13:38 +0100)]
lan78xx: enable auto speed configuration for LAN7850 if no EEPROM is detected
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Linus Torvalds [Mon, 26 Feb 2024 19:06:30 +0000 (11:06 -0800)]
Merge tag 'mtd/fixes-for-6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
"Many NAND page layouts have been added to the Marvell NAND controller
but could not be used in practice so they are being removed.
Regarding the SPI-NAND area, Gigadevice chips were not using the right
buffer for an ECC status check operation.
Aside from these driver fixes, there is also a refcount fix in the MTD
core nodes parsing logic"
* tag 'mtd/fixes-for-6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: marvell: fix layouts
mtd: Fix possible refcounting issue when going through partition nodes
mtd: spinand: gigadevice: Fix the get ecc status issue
Linus Torvalds [Mon, 26 Feb 2024 19:00:54 +0000 (11:00 -0800)]
Merge tag 'for-6.8-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A more fixes for recently reported or discovered problems:
- fix corner case of send that would generate potentially large
stream of zeros if there's a hole at the end of the file
- fix chunk validation in zoned mode on conventional zones, it was
possible to create chunks that would not be allowed on sequential
zones
- fix validation of dev-replace ioctl filenames
- fix KCSAN warnings about access to block reserve struct members"
* tag 'for-6.8-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix data race at btrfs_use_block_rsv() when accessing block reserve
btrfs: fix data races when accessing the reserved amount of block reserves
btrfs: send: don't issue unnecessary zero writes for trailing hole
btrfs: dev-replace: properly validate device names
btrfs: zoned: don't skip block group profile checks on conventional zones
Mickaël Salaün [Mon, 19 Feb 2024 19:03:45 +0000 (20:03 +0100)]
landlock: Fix asymmetric private inodes referring
When linking or renaming a file, if only one of the source or
destination directory is backed by an S_PRIVATE inode, then the related
set of layer masks would be used as uninitialized by
is_access_to_paths_allowed(). This would result to indeterministic
access for one side instead of always being allowed.
This bug could only be triggered with a mounted filesystem containing
both S_PRIVATE and !S_PRIVATE inodes, which doesn't seem possible.
The collect_domain_accesses() calls return early if
is_nouser_or_private() returns false, which means that the directory's
superblock has SB_NOUSER or its inode has S_PRIVATE. Because rename or
link actions are only allowed on the same mounted filesystem, the
superblock is always the same for both source and destination
directories. However, it might be possible in theory to have an
S_PRIVATE parent source inode with an !S_PRIVATE parent destination
inode, or vice versa.
To make sure this case is not an issue, explicitly initialized both set
of layer masks to 0, which means to allow all actions on the related
side. If at least on side has !S_PRIVATE, then
collect_domain_accesses() and is_access_to_paths_allowed() check for the
required access rights.
Eric Dumazet [Thu, 22 Feb 2024 12:17:47 +0000 (12:17 +0000)]
ipv6: fix potential "struct net" leak in inet6_rtm_getaddr()
It seems that if userspace provides a correct IFA_TARGET_NETNSID value
but no IFA_ADDRESS and IFA_LOCAL attributes, inet6_rtm_getaddr()
returns -EINVAL with an elevated "struct net" refcount.
Jakub Kicinski [Wed, 21 Feb 2024 23:12:10 +0000 (15:12 -0800)]
net: veth: clear GRO when clearing XDP even when down
veth sets NETIF_F_GRO automatically when XDP is enabled,
because both features use the same NAPI machinery.
The logic to clear NETIF_F_GRO sits in veth_disable_xdp() which
is called both on ndo_stop and when XDP is turned off.
To avoid the flag from being cleared when the device is brought
down, the clearing is skipped when IFF_UP is not set.
Bringing the device down should indeed not modify its features.
Unfortunately, this means that clearing is also skipped when
XDP is disabled _while_ the device is down. And there's nothing
on the open path to bring the device features back into sync.
IOW if user enables XDP, disables it and then brings the device
up we'll end up with a stray GRO flag set but no NAPI instances.
We don't depend on the GRO flag on the datapath, so the datapath
won't crash. We will crash (or hang), however, next time features
are sync'ed (either by user via ethtool or peer changing its config).
The GRO flag will go away, and veth will try to disable the NAPIs.
But the open path never created them since XDP was off, the GRO flag
was a stray. If NAPI was initialized before we'll hang in napi_disable().
If it never was we'll crash trying to stop uninitialized hrtimer.
Move the GRO flag updates to the XDP enable / disable paths,
instead of mixing them with the ndo_open / ndo_close paths.
Linus Torvalds [Sun, 25 Feb 2024 23:31:57 +0000 (15:31 -0800)]
Merge tag 'bcachefs-2024-02-25' of https://evilpiepirate.org/git/bcachefs
Pull bcachefs fixes from Kent Overstreet:
"Some more mostly boring fixes, but some not
User reported ones:
- the BTREE_ITER_FILTER_SNAPSHOTS one fixes a really nasty
performance bug; user reported an untar initially taking two
seconds and then ~2 minutes
- kill a __GFP_NOFAIL in the buffered read path; this was a leftover
from the trickier fix to kill __GFP_NOFAIL in readahead, where we
can't return errors (and have to silently truncate the read
ourselves).
bcachefs can't use GFP_NOFAIL for folio state unlike iomap based
filesystems because our folio state is just barely too big, 2MB
hugepages cause us to exceed the 2 page threshhold for GFP_NOFAIL.
additionally, the flags argument was just buggy, we weren't
supplying GFP_KERNEL previously (!)"
* tag 'bcachefs-2024-02-25' of https://evilpiepirate.org/git/bcachefs:
bcachefs: fix bch2_save_backtrace()
bcachefs: Fix check_snapshot() memcpy
bcachefs: Fix bch2_journal_flush_device_pins()
bcachefs: fix iov_iter count underflow on sub-block dio read
bcachefs: Fix BTREE_ITER_FILTER_SNAPSHOTS on inodes btree
bcachefs: Kill __GFP_NOFAIL in buffered read path
bcachefs: fix backpointer_to_text() when dev does not exist
Linus Torvalds [Sun, 25 Feb 2024 18:58:12 +0000 (10:58 -0800)]
Merge tag 'docs-6.8-fixes3' of git://git.lwn.net/linux
Pull two documentation build fixes from Jonathan Corbet:
- The XFS online fsck documentation uses incredibly deeply nested
subsection and list nesting; that broke the PDF docs build. Tweak a
parameter to tell LaTeX to allow the deeper nesting.
- Fix a 6.8 PDF-build regression
* tag 'docs-6.8-fixes3' of git://git.lwn.net/linux:
docs: translations: use attribute to store current language
docs: Instruct LaTeX to cope with deeper nesting
Linus Torvalds [Sun, 25 Feb 2024 18:41:57 +0000 (10:41 -0800)]
Merge tag 'usb-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 6.8-rc6 to resolve some reported
problems. These include:
- regression fixes with typec tpcm code as reported by many
- cdnsp and cdns3 driver fixes
- usb role setting code bugfixes
- build fix for uhci driver
- ncm gadget driver bugfix
- MAINTAINERS entry update
All of these have been in linux-next all week with no reported issues
and there is at least one fix in here that is in Thorsten's regression
list that is being tracked"
* tag 'usb-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tpcm: Fix issues with power being removed during reset
MAINTAINERS: Drop myself as maintainer of TYPEC port controller drivers
usb: gadget: ncm: Avoid dropping datagrams of properly parsed NTBs
Revert "usb: typec: tcpm: reset counter when enter into unattached state after try role"
usb: gadget: omap_udc: fix USB gadget regression on Palm TE
usb: dwc3: gadget: Don't disconnect if not started
usb: cdns3: fix memory double free when handle zero packet
usb: cdns3: fixed memory use after free at cdns3_gadget_ep_disable()
usb: roles: don't get/set_role() when usb_role_switch is unregistered
usb: roles: fix NULL pointer issue when put module's reference
usb: cdnsp: fixed issue with incorrect detecting CDNSP family controllers
usb: cdnsp: blocked some cdns3 specific code
usb: uhci-grlib: Explicitly include linux/platform_device.h
Linus Torvalds [Sun, 25 Feb 2024 18:35:41 +0000 (10:35 -0800)]
Merge tag 'tty-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are three small serial/tty driver fixes for 6.8-rc6 that resolve
the following reported errors:
- riscv hvc console driver fix that was reported by many
- amba-pl011 serial driver fix for RS485 mode
- stm32 serial driver fix for RS485 mode
All of these have been in linux-next all week with no reported
problems"
* tag 'tty-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: amba-pl011: Fix DMA transmission in RS485 mode
serial: stm32: do not always set SER_RS485_RX_DURING_TX if RS485 is enabled
tty: hvc: Don't enable the RISC-V SBI console by default
Linus Torvalds [Sun, 25 Feb 2024 18:22:21 +0000 (10:22 -0800)]
Merge tag 'x86_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Make sure clearing CPU buffers using VERW happens at the latest
possible point in the return-to-userspace path, otherwise memory
accesses after the VERW execution could cause data to land in CPU
buffers again
* tag 'x86_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM/VMX: Move VERW closer to VMentry for MDS mitigation
KVM/VMX: Use BT+JNC, i.e. EFLAGS.CF to select VMRESUME vs. VMLAUNCH
x86/bugs: Use ALTERNATIVE() instead of mds_user_clear static key
x86/entry_32: Add VERW just before userspace transition
x86/entry_64: Add VERW just before userspace transition
x86/bugs: Add asm helpers for executing VERW
Linus Torvalds [Sun, 25 Feb 2024 18:14:12 +0000 (10:14 -0800)]
Merge tag 'irq_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Make sure GICv4 always gets initialized to prevent a kexec-ed kernel
from silently failing to set it up
- Do not call bus_get_dev_root() for the mbigen irqchip as it always
returns NULL - use NULL directly
- Fix hardware interrupt number truncation when assigning MSI
interrupts
- Correct sending end-of-interrupt messages to disabled interrupts
lines on RISC-V PLIC
* tag 'irq_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Do not assume vPE tables are preallocated
irqchip/mbigen: Don't use bus_get_dev_root() to find the parent
PCI/MSI: Prevent MSI hardware interrupt number truncation
irqchip/sifive-plic: Enable interrupt if needed before EOI
Linus Torvalds [Sun, 25 Feb 2024 17:29:05 +0000 (09:29 -0800)]
Merge tag 'pull-fixes.pathwalk-rcu-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull RCU pathwalk fixes from Al Viro:
"We still have some races in filesystem methods when exposed to RCU
pathwalk. This series is a result of code audit (the second round of
it) and it should deal with most of that stuff.
Still pending: ntfs3 ->d_hash()/->d_compare() and ceph_d_revalidate().
Up to maintainers (a note for NTFS folks - when documentation says
that a method may not block, it *does* imply that blocking allocations
are to be avoided. Really)"
[ More explanations for people who aren't familiar with the vagaries of
RCU path walking: most of it is hidden from filesystems, but if a
filesystem actively participates in the low-level path walking it
needs to make sure the fields involved in that walk are RCU-safe.
That "actively participate in low-level path walking" includes things
like having its own ->d_hash()/->d_compare() routines, or by having
its own directory permission function that doesn't just use the common
helpers. Having a ->d_revalidate() function will also have this issue.
Note that instead of making everything RCU safe you can also choose to
abort the RCU pathwalk if your operation cannot be done safely under
RCU, but that obviously comes with a performance penalty. One common
pattern is to allow the simple cases under RCU, and abort only if you
need to do something more complicated.
So not everything needs to be RCU-safe, and things like the inode etc
that the VFS itself maintains obviously already are. But these fixes
tend to be about properly RCU-delaying things like ->s_fs_info that
are maintained by the filesystem and that got potentially released too
early. - Linus ]
* tag 'pull-fixes.pathwalk-rcu-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ext4_get_link(): fix breakage in RCU mode
cifs_get_link(): bail out in unsafe case
fuse: fix UAF in rcu pathwalks
procfs: make freeing proc_fs_info rcu-delayed
procfs: move dropping pde and pid from ->evict_inode() to ->free_inode()
nfs: fix UAF on pathwalk running into umount
nfs: make nfs_set_verifier() safe for use in RCU pathwalk
afs: fix __afs_break_callback() / afs_drop_open_mmap() race
hfsplus: switch to rcu-delayed unloading of nls and freeing ->s_fs_info
exfat: move freeing sbi, upcase table and dropping nls into rcu-delayed helper
affs: free affs_sb_info with kfree_rcu()
rcu pathwalk: prevent bogus hard errors from may_lookup()
fs/super.c: don't drop ->s_user_ns until we free struct super_block itself
Linus Torvalds [Sun, 25 Feb 2024 17:17:15 +0000 (09:17 -0800)]
Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes - revert of regression from this cycle and a fix for
erofs failure exit breakage (had been there since way back)"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
erofs: fix handling kern_mount() failure
Revert "get rid of DCACHE_GENOCIDE"
Al Viro [Sat, 3 Feb 2024 06:17:34 +0000 (01:17 -0500)]
ext4_get_link(): fix breakage in RCU mode
1) errors from ext4_getblk() should not be propagated to caller
unless we are really sure that we would've gotten the same error
in non-RCU pathwalk.
2) we leak buffer_heads if ext4_getblk() is successful, but bh is
not uptodate.
Al Viro [Wed, 20 Sep 2023 02:28:16 +0000 (22:28 -0400)]
cifs_get_link(): bail out in unsafe case
->d_revalidate() bails out there, anyway. It's not enough
to prevent getting into ->get_link() in RCU mode, but that
could happen only in a very contrieved setup. Not worth
trying to do anything fancy here unless ->d_revalidate()
stops kicking out of RCU mode at least in some cases.
Al Viro [Thu, 28 Sep 2023 04:19:39 +0000 (00:19 -0400)]
fuse: fix UAF in rcu pathwalks
->permission(), ->get_link() and ->inode_get_acl() might dereference
->s_fs_info (and, in case of ->permission(), ->s_fs_info->fc->user_ns
as well) when called from rcu pathwalk.
Freeing ->s_fs_info->fc is rcu-delayed; we need to make freeing ->s_fs_info
and dropping ->user_ns rcu-delayed too.
Al Viro [Wed, 20 Sep 2023 04:12:00 +0000 (00:12 -0400)]
procfs: make freeing proc_fs_info rcu-delayed
makes proc_pid_ns() safe from rcu pathwalk (put_pid_ns()
is still synchronous, but that's not a problem - it does
rcu-delay everything that needs to be)
Al Viro [Thu, 28 Sep 2023 02:11:26 +0000 (22:11 -0400)]
nfs: fix UAF on pathwalk running into umount
NFS ->d_revalidate(), ->permission() and ->get_link() need to access
some parts of nfs_server when called in RCU mode:
server->flags
server->caps
*(server->io_stats)
and, worst of all, call
server->nfs_client->rpc_ops->have_delegation
(the last one - as NFS_PROTO(inode)->have_delegation()). We really
don't want to RCU-delay the entire nfs_free_server() (it would have
to be done with schedule_work() from RCU callback, since it can't
be made to run from interrupt context), but actual freeing of
nfs_server and ->io_stats can be done via call_rcu() just fine.
nfs_client part is handled simply by making nfs_free_client() use
kfree_rcu().
Al Viro [Thu, 28 Sep 2023 01:50:25 +0000 (21:50 -0400)]
nfs: make nfs_set_verifier() safe for use in RCU pathwalk
nfs_set_verifier() relies upon dentry being pinned; if that's
the case, grabbing ->d_lock stabilizes ->d_parent and guarantees
that ->d_parent points to a positive dentry. For something
we'd run into in RCU mode that is *not* true - dentry might've
been through dentry_kill() just as we grabbed ->d_lock, with
its parent going through the same just as we get to into
nfs_set_verifier_locked(). It might get to detaching inode
(and zeroing ->d_inode) before nfs_set_verifier_locked() gets
to fetching that; we get an oops as the result.
That can happen in nfs{,4} ->d_revalidate(); the call chain in
question is nfs_set_verifier_locked() <- nfs_set_verifier() <-
nfs_lookup_revalidate_delegated() <- nfs{,4}_do_lookup_revalidate().
We have checked that the parent had been positive, but that's
done before we get to nfs_set_verifier() and it's possible for
memory pressure to pick our dentry as eviction candidate by that
time. If that happens, back-to-back attempts to kill dentry and
its parent are quite normal. Sure, in case of eviction we'll
fail the ->d_seq check in the caller, but we need to survive
until we return there...
In __afs_break_callback() we might check ->cb_nr_mmap and if it's non-zero
do queue_work(&vnode->cb_work). In afs_drop_open_mmap() we decrement
->cb_nr_mmap and do flush_work(&vnode->cb_work) if it reaches zero.
The trouble is, there's nothing to prevent __afs_break_callback() from
seeing ->cb_nr_mmap before the decrement and do queue_work() after both
the decrement and flush_work(). If that happens, we might be in trouble -
vnode might get freed before the queued work runs.
__afs_break_callback() is always done under ->cb_lock, so let's make
sure that ->cb_nr_mmap can change from non-zero to zero while holding
->cb_lock (the spinlock component of it - it's a seqlock and we don't
need to mess with the counter).
Al Viro [Tue, 19 Sep 2023 19:53:32 +0000 (15:53 -0400)]
exfat: move freeing sbi, upcase table and dropping nls into rcu-delayed helper
That stuff can be accessed by ->d_hash()/->d_compare(); as it is, we have
a hard-to-hit UAF if rcu pathwalk manages to get into ->d_hash() on a filesystem
that is in process of getting shut down.
Besides, having nls and upcase table cleanup moved from ->put_super() towards
the place where sbi is freed makes for simpler failure exits.
Al Viro [Sat, 30 Sep 2023 01:11:41 +0000 (21:11 -0400)]
rcu pathwalk: prevent bogus hard errors from may_lookup()
If lazy call of ->permission() returns a hard error, check that
try_to_unlazy() succeeds before returning it. That both makes
life easier for ->permission() instances and closes the race
in ENOTDIR handling - it is possible that positive d_can_lookup()
seen in link_path_walk() applies to the state *after* unlink() +
mkdir(), while nd->inode matches the state prior to that.
Normally seeing e.g. EACCES from permission check in rcu pathwalk
means that with some timings non-rcu pathwalk would've run into
the same; however, running into a non-executable regular file
in the middle of a pathname would not get to permission check -
it would fail with ENOTDIR instead.
Kent Overstreet [Sat, 24 Feb 2024 06:18:45 +0000 (01:18 -0500)]
bcachefs: Fix check_snapshot() memcpy
check_snapshot() copies the bch_snapshot to a temporary to easily handle
older versions that don't have all the fields of the current version,
but it lacked a min() to correctly handle keys newer and larger than the
current version.
Brian Foster [Thu, 15 Feb 2024 17:16:05 +0000 (12:16 -0500)]
bcachefs: fix iov_iter count underflow on sub-block dio read
bch2_direct_IO_read() checks the request offset and size for sector
alignment and then falls through to a couple calculations to shrink
the size of the request based on the inode size. The problem is that
these checks round up to the fs block size, which runs the risk of
underflowing iter->count if the block size happens to be large
enough. This is triggered by fstest generic/361 with a 4k block
size, which subsequently leads to a crash. To avoid this crash,
check that the shorten length doesn't exceed the overall length of
the iter.
Kent Overstreet [Sun, 25 Feb 2024 00:14:36 +0000 (19:14 -0500)]
bcachefs: Fix BTREE_ITER_FILTER_SNAPSHOTS on inodes btree
If we're in FILTER_SNAPSHOTS mode and we start scanning a range of the
keyspace where no keys are visible in the current snapshot, we have a
problem - we'll scan for a very long time before scanning terminates.
Awhile back, this was fixed for most cases with peek_upto() (and
assertions that enforce that it's being used).
But the fix missed the fact that the inodes btree is different - every
key offset is in a different snapshot tree, not just the inode field.
Kent Overstreet [Fri, 23 Feb 2024 02:39:13 +0000 (21:39 -0500)]
bcachefs: Kill __GFP_NOFAIL in buffered read path
Recently, we fixed our __GFP_NOFAIL usage in the readahead path, but the
easy one in read_single_folio() (where wa can return an error) was
missed - oops.
Linus Torvalds [Sat, 24 Feb 2024 23:59:26 +0000 (15:59 -0800)]
Merge tag 'iommu-fixes-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Intel VT-d fixes for nested domain handling:
- Cache invalidation for changes in a parent domain
- Dirty tracking setting for parent and nested domains
- Fix a constant-out-of-range warning
- ARM SMMU fixes:
- Fix CD allocation from atomic context when using SVA with SMMUv3
- Revert the conversion of SMMUv2 to domain_alloc_paging(), as it
breaks the boot for Qualcomm MSM8996 devices
- Restore SVA handle sharing in core code as it turned out there are
still drivers relying on it
* tag 'iommu-fixes-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/sva: Restore SVA handle sharing
iommu/arm-smmu-v3: Do not use GFP_KERNEL under as spinlock
iommu/vt-d: Fix constant-out-of-range warning
iommu/vt-d: Set SSADE when attaching to a parent with dirty tracking
iommu/vt-d: Add missing dirty tracking set for parent domain
iommu/vt-d: Wrap the dirty tracking loop to be a helper
iommu/vt-d: Remove domain parameter for intel_pasid_setup_dirty_tracking()
iommu/vt-d: Add missing device iotlb flush for parent domain
iommu/vt-d: Update iotlb in nested domain attach
iommu/vt-d: Add missing iotlb flush for parent domain
iommu/vt-d: Add __iommu_flush_iotlb_psi()
iommu/vt-d: Track nested domains in parent
Revert "iommu/arm-smmu: Convert to domain_alloc_paging()"
Linus Torvalds [Sat, 24 Feb 2024 23:53:40 +0000 (15:53 -0800)]
Merge tag 'cxl-fixes-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dan Williams:
"A collection of significant fixes for the CXL subsystem.
The largest change in this set, that bordered on "new development", is
the fix for the fact that the location of the new qos_class attribute
did not match the Documentation. The fix ends up deleting more code
than it added, and it has a new unit test to backstop basic errors in
this interface going forward. So the "red-diff" and unit test saved
the "rip it out and try again" response.
In contrast, the new notification path for firmware reported CXL
errors (CXL CPER notifications) has a locking context bug that can not
be fixed with a red-diff. Given where the release cycle stands, it is
not comfortable to squeeze in that fix in these waning days. So, that
receives the "back it out and try again later" treatment.
There is a regression fix in the code that establishes memory NUMA
nodes for platform CXL regions. That has an ack from x86 folks. There
are a couple more fixups for Linux to understand (reassemble) CXL
regions instantiated by platform firmware. The policy around platforms
that do not match host-physical-address with system-physical-address
(i.e. systems that have an address translation mechanism between the
address range reported in the ACPI CEDT.CFMWS and endpoint decoders)
has been softened to abort driver load rather than teardown the memory
range (can cause system hangs). Lastly, there is a robustness /
regression fix for cases where the driver would previously continue in
the face of error, and a fixup for PCI error notification handling.
Summary:
- Fix NUMA initialization from ACPI CEDT.CFMWS
- Fix region assembly failures due to async init order
- Fix / simplify export of qos_class information
- Fix cxl_acpi initialization vs single-window-init failures
- Fix handling of repeated 'pci_channel_io_frozen' notifications
- Workaround platforms that violate host-physical-address ==
system-physical address assumptions
- Defer CXL CPER notification handling to v6.9"
* tag 'cxl-fixes-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/acpi: Fix load failures due to single window creation failure
acpi/ghes: Remove CXL CPER notifications
cxl/pci: Fix disabling memory if DVSEC CXL Range does not match a CFMWS window
cxl/test: Add support for qos_class checking
cxl: Fix sysfs export of qos_class for memdev
cxl: Remove unnecessary type cast in cxl_qos_class_verify()
cxl: Change 'struct cxl_memdev_state' *_perf_list to single 'struct cxl_dpa_perf'
cxl/region: Allow out of order assembly of autodiscovered regions
cxl/region: Handle endpoint decoders in cxl_region_find_decoder()
x86/numa: Fix the sort compare func used in numa_fill_memblks()
x86/numa: Fix the address overlap check in numa_fill_memblks()
cxl/pci: Skip to handle RAS errors if CXL.mem device is detached
Linus Torvalds [Sat, 24 Feb 2024 17:55:29 +0000 (09:55 -0800)]
Merge tag 'for-6.8/dm-fix-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
- Fix DM integrity and verity targets to not use excessive stack when
they recheck in the error path.
* tag 'for-6.8/dm-fix-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm-integrity, dm-verity: reduce stack usage for recheck
Linus Torvalds [Sat, 24 Feb 2024 17:49:16 +0000 (09:49 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes: the four driver ones are pretty trivial.
The larger two core changes are to try to fix various USB attached
devices which have somewhat eccentric ways of handling the VPD and
other mode pages which necessitate multiple revalidates (that were
removed in the interests of efficiency) and updating the heuristic for
supported VPD pages"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: jazz_esp: Only build if SCSI core is builtin
scsi: smartpqi: Fix disable_managed_interrupts
scsi: ufs: Uninitialized variable in ufshcd_devfreq_target()
scsi: target: pscsi: Fix bio_put() for error case
scsi: core: Consult supported VPD page list prior to fetching page
scsi: sd: usb_storage: uas: Access media prior to querying device properties
Linus Torvalds [Sat, 24 Feb 2024 17:36:35 +0000 (09:36 -0800)]
Merge tag 'loongarch-fixes-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix two cpu-hotplug issues, fix the init sequence about FDT system,
fix the coding style of dts, and fix the wrong CPUCFG ID handling of
KVM"
* tag 'loongarch-fixes-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Streamline kvm_check_cpucfg() and improve comments
LoongArch: KVM: Rename _kvm_get_cpucfg() to _kvm_get_cpucfg_mask()
LoongArch: KVM: Fix input validation of _kvm_get_cpucfg() & kvm_check_cpucfg()
LoongArch: dts: Minor whitespace cleanup
LoongArch: Call early_init_fdt_scan_reserved_mem() earlier
LoongArch: Update cpu_sibling_map when disabling nonboot CPUs
LoongArch: Disable IRQ before init_fn() for nonboot CPUs
Arnd Bergmann [Sat, 24 Feb 2024 13:48:03 +0000 (14:48 +0100)]
dm-integrity, dm-verity: reduce stack usage for recheck
The newly added integrity_recheck() function has another larger stack
allocation, just like its caller integrity_metadata(). When it gets
inlined, the combination of the two exceeds the warning limit for 32-bit
architectures and possibly risks an overflow when this is called from
a deep call chain through a file system:
Since the caller at this point is done using its checksum buffer,
just reuse the same buffer in the new function to avoid the double
allocation.
[Mikulas: add "noinline" to integrity_recheck and verity_recheck.
These functions are only called on error, so they shouldn't bloat the
stack frame or code size of the caller.]
Fixes: c88f5e553fe3 ("dm-integrity: recheck the integrity tag after a failure") Fixes: 9177f3c0dea6 ("dm-verity: recheck the hash after a failure") Cc: [email protected] Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: Mikulas Patocka <[email protected]> Signed-off-by: Mike Snitzer <[email protected]>
Doug Smythies [Sat, 17 Feb 2024 21:30:10 +0000 (13:30 -0800)]
cpufreq: intel_pstate: fix pstate limits enforcement for adjust_perf call back
There is a loophole in pstate limit clamping for the intel_cpufreq CPU
frequency scaling driver (intel_pstate in passive mode), schedutil CPU
frequency scaling governor, HWP (HardWare Pstate) control enabled, when
the adjust_perf call back path is used.
Fix it.
Fixes: a365ab6b9dfb cpufreq: intel_pstate: Implement the ->adjust_perf() callback Signed-off-by: Doug Smythies <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
mm/debug_vm_pgtable: fix BUG_ON with pud advanced test
Architectures like powerpc add debug checks to ensure we find only devmap
PUD pte entries. These debug checks are only done with CONFIG_DEBUG_VM.
This patch marks the ptes used for PUD advanced test devmap pte entries so
that we don't hit on debug checks on architecture like ppc64 as below.
Nhat Pham [Tue, 20 Feb 2024 03:01:21 +0000 (19:01 -0800)]
mm: cachestat: fix folio read-after-free in cache walk
In cachestat, we access the folio from the page cache's xarray to compute
its page offset, and check for its dirty and writeback flags. However, we
do not hold a reference to the folio before performing these actions,
which means the folio can concurrently be released and reused as another
folio/page/slab.
Get around this altogether by just using xarray's existing machinery for
the folio page offsets and dirty/writeback states.
This changes behavior for tmpfs files to now always report zeroes in their
dirty and writeback counters. This is okay as tmpfs doesn't follow
conventional writeback cache behavior: its pages get "cleaned" during
swapout, after which they're no longer resident etc.
Lorenzo Stoakes [Tue, 20 Feb 2024 06:44:10 +0000 (06:44 +0000)]
MAINTAINERS: add memory mapping entry with reviewers
Recently there have been a number of patches which have affected various
aspects of the memory mapping logic as implemented in mm/mmap.c where it
would have been useful for regular contributors to have been notified.
Add an entry for this part of mm in particular with regular contributors
tagged as reviewers.
Byungchul Park [Fri, 16 Feb 2024 11:15:02 +0000 (20:15 +0900)]
mm/vmscan: fix a bug calling wakeup_kswapd() with a wrong zone index
With numa balancing on, when a numa system is running where a numa node
doesn't have its local memory so it has no managed zones, the following
oops has been observed. It's because wakeup_kswapd() is called with a
wrong zone index, -1. Fixed it by checking the index before calling
wakeup_kswapd().
Marco Elver [Mon, 29 Jan 2024 10:07:02 +0000 (11:07 +0100)]
kasan: revert eviction of stack traces in generic mode
This partially reverts commits cc478e0b6bdf, 63b85ac56a64, 08d7c94d9635, a414d4286f34, and 773688a6cb24 to make use of variable-sized stack depot
records, since eviction of stack entries from stack depot forces fixed-
sized stack records. Care was taken to retain the code cleanups by the
above commits.
Eviction was added to generic KASAN as a response to alleviating the
additional memory usage from fixed-sized stack records, but this still
uses more memory than previously.
With the re-introduction of variable-sized records for stack depot, we can
just switch back to non-evictable stack records again, and return back to
the previous performance and memory usage baseline.
As can be seen from the counters, with a generic KASAN config, refcounted
allocations and evictions are no longer used. Due to using variable-sized
records, I observe a reduction of 278 stack depot pools (saving 4448 KiB)
with my test setup.
Marco Elver [Mon, 29 Jan 2024 10:07:01 +0000 (11:07 +0100)]
stackdepot: use variable size records for non-evictable entries
With the introduction of stack depot evictions, each stack record is now
fixed size, so that future reuse after an eviction can safely store
differently sized stack traces. In all cases that do not make use of
evictions, this wastes lots of space.
Fix it by re-introducing variable size stack records (up to the max
allowed size) for entries that will never be evicted. We know if an entry
will never be evicted if the flag STACK_DEPOT_FLAG_GET is not provided,
since a later stack_depot_put() attempt is undefined behavior.
With my current kernel config that enables KASAN and also SLUB owner
tracking, I observe (after a kernel boot) a whopping reduction of 296
stack depot pools, which translates into 4736 KiB saved. The savings here
are from SLUB owner tracking only, because KASAN generic mode still uses
refcounting.
Ard Biesheuvel [Fri, 23 Feb 2024 13:20:35 +0000 (14:20 +0100)]
crypto: arm64/neonbs - fix out-of-bounds access on short input
The bit-sliced implementation of AES-CTR operates on blocks of 128
bytes, and will fall back to the plain NEON version for tail blocks or
inputs that are shorter than 128 bytes to begin with.
It will call straight into the plain NEON asm helper, which performs all
memory accesses in granules of 16 bytes (the size of a NEON register).
For this reason, the associated plain NEON glue code will copy inputs
shorter than 16 bytes into a temporary buffer, given that this is a rare
occurrence and it is not worth the effort to work around this in the asm
code.
The fallback from the bit-sliced NEON version fails to take this into
account, potentially resulting in out-of-bounds accesses. So clone the
same workaround, and use a temp buffer for short in/outputs.
Herbert Xu [Wed, 21 Feb 2024 09:07:44 +0000 (17:07 +0800)]
crypto: lskcipher - Copy IV in lskcipher glue code always
The lskcipher glue code for skcipher needs to copy the IV every
time rather than only on the first and last request. Otherwise
those algorithms that use IV to perform chaining may break, e.g.,
CBC.
This is because crypto_skcipher_import/export do not include the
IV as part of the saved state.
Reported-by: [email protected] Fixes: 662ea18d089b ("crypto: skcipher - Make use of internal state") Signed-off-by: Herbert Xu <[email protected]>
Corey Minyard [Wed, 21 Feb 2024 19:27:13 +0000 (20:27 +0100)]
i2c: imx: when being a target, mark the last read as processed
When being a target, NAK from the controller means that all bytes have
been transferred. So, the last byte needs also to be marked as
'processed'. Otherwise index registers of backends may not increase.
Fixes: f7414cd6923f ("i2c: imx: support slave mode for imx I2C driver") Signed-off-by: Corey Minyard <[email protected]> Tested-by: Andrew Manley <[email protected]> Reviewed-by: Andrew Manley <[email protected]> Reviewed-by: Oleksij Rempel <[email protected]>
[wsa: fixed comment and commit message to properly describe the case] Signed-off-by: Wolfram Sang <[email protected]> Signed-off-by: Andi Shyti <[email protected]>
Mickaël Salaün [Fri, 23 Feb 2024 19:05:46 +0000 (20:05 +0100)]
apparmor: fix lsm_get_self_attr()
In apparmor_getselfattr() when an invalid AppArmor attribute is
requested, or a value hasn't been explicitly set for the requested
attribute, the label passed to aa_put_label() is not properly
initialized which can cause problems when the pointer value is non-NULL
and AppArmor attempts to drop a reference on the bogus label object.
Mickaël Salaün [Fri, 23 Feb 2024 19:05:45 +0000 (20:05 +0100)]
selinux: fix lsm_get_self_attr()
selinux_getselfattr() doesn't properly initialize the string pointer
it passes to selinux_lsm_getattr() which can cause a problem when an
attribute hasn't been explicitly set; selinux_lsm_getattr() returns
0/success, but does not set or initialize the string label/attribute.
Failure to properly initialize the string causes problems later in
selinux_getselfattr() when the function attempts to kfree() the
string.
Cc: Casey Schaufler <[email protected]> Fixes: 762c934317e6 ("SELinux: Add selfattr hooks") Suggested-by: Paul Moore <[email protected]>
[PM: description changes as discussed in the thread] Signed-off-by: Mickaël Salaün <[email protected]> Signed-off-by: Paul Moore <[email protected]>
Linus Torvalds [Fri, 23 Feb 2024 18:40:20 +0000 (10:40 -0800)]
Merge tag 'parisc-for-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
"Fixes CPU hotplug, the parisc stack unwinder and two possible build
errors in kprobes and ftrace area:
- Fix CPU hotplug
- Fix unaligned accesses and faults in stack unwinder
- Fix potential build errors by always including asm-generic/kprobes.h
- Fix build bug by add missing CONFIG_DYNAMIC_FTRACE check"
* tag 'parisc-for-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix stack unwinder
parisc/kprobes: always include asm-generic/kprobes.h
parisc/ftrace: add missing CONFIG_DYNAMIC_FTRACE check
Revert "parisc: Only list existing CPUs in cpu_possible_mask"
Linus Torvalds [Fri, 23 Feb 2024 18:31:28 +0000 (10:31 -0800)]
Merge tag 'arm-fixes-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull arm and RISC-V SoC fixes from Arnd Bergmann:
"The Rockchip and IMX8 platforms get a number of fixes for dts files in
order to address some misconfigurations, including a regression for
USB-C support on some boards.
The other dts fixes are part of a series by Rob Herring to clean up
another class of dtc compiler warnings across all platforms, with a
few others helping out as well. With this, we can enable the warning
for the coming merge window without introducing regressions.
Conor Dooley has collected fixes for RISC-V platforms, both for the
dts files and for platofrm specific drivers.
The ep93xx platform gets a regression for for its gpio descriptors"
* tag 'arm-fixes-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (28 commits)
ARM: dts: renesas: rcar-gen2: Add missing #interrupt-cells to DA9063 nodes
cache: ax45mp_cache: Align end size to cache boundary in ax45mp_dma_cache_wback()
arm64: dts: qcom: Fix interrupt-map cell sizes
arm: dts: Fix dtc interrupt_map warnings
arm64: dts: Fix dtc interrupt_provider warnings
arm: dts: Fix dtc interrupt_provider warnings
arm64: dts: freescale: Disable interrupt_map check
ARM: ep93xx: Add terminator to gpiod_lookup_table
riscv: dts: sifive: add missing #interrupt-cells to pmic
arm64: dts: rockchip: Correct Indiedroid Nova GPIO Names
arm64: dts: rockchip: Drop interrupts property from rk3328 pwm-rockchip node
arm64: dts: rockchip: set num-cs property for spi on px30
arm64: dts: rockchip: minor rk3588 whitespace cleanup
riscv: dts: starfive: replace underscores in node names
bus: imx-weim: fix valid range check
Revert "arm64: dts: imx8mn-var-som-symphony: Describe the USB-C connector"
Revert "arm64: dts: imx8mp-dhcom-pdk3: Describe the USB-C connector"
arm64: dts: tqma8mpql: fix audio codec iov-supply
arm64: dts: rockchip: drop unneeded status from rk3588-jaguar gpio-leds
ARM: dts: rockchip: Drop interrupts property from pwm-rockchip nodes
...
Linus Torvalds [Fri, 23 Feb 2024 18:26:43 +0000 (10:26 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A simple fix to a definition in the CXL PMU driver, a couple of
patches to restore SME control registers on the resume path (since
Arm's fast model now clears them) and a revert for our jump label asm
constraints after Geert noticed they broke the build with GCC 5.5.
There was then the ensuing discussion about raising the minimum GCC
(and corresponding binutils) versions at [1], but for now we'll keep
things working as they were until that goes ahead.
- Revert fix to jump label asm constraints, as it regresses the build
with some GCC 5.5 toolchains.
- Restore SME control registers when resuming from suspend
- Fix incorrect filter definition in CXL PMU driver"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/sme: Restore SMCR_EL1.EZT0 on exit from suspend
arm64/sme: Restore SME registers on exit from suspend
Revert "arm64: jump_label: use constraints "Si" instead of "i""
perf: CXL: fix CPMU filter value mask length
Linus Torvalds [Fri, 23 Feb 2024 17:54:13 +0000 (09:54 -0800)]
Merge tag 's390-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- Fix invalid -EBUSY on ccw_device_start() which can lead to failing
device initialization
- Add missing multiplication by 8 in __iowrite64_copy() to get the
correct byte length before calling zpci_memcpy_toio()
- Various config updates
* tag 's390-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: fix invalid -EBUSY on ccw_device_start
s390: use the correct count for __iowrite64_copy()
s390/configs: update default configurations
s390/configs: enable INIT_STACK_ALL_ZERO in all configurations
s390/configs: provide compat topic configuration target
Linus Torvalds [Fri, 23 Feb 2024 17:43:21 +0000 (09:43 -0800)]
Merge tag 'mm-hotfixes-stable-2024-02-22-15-02' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"A batch of MM (and one non-MM) hotfixes.
Ten are cc:stable and the remainder address post-6.7 issues or aren't
considered appropriate for backporting"
* tag 'mm-hotfixes-stable-2024-02-22-15-02' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
kasan: guard release_free_meta() shadow access with kasan_arch_is_ready()
mm/damon/lru_sort: fix quota status loss due to online tunings
mm/damon/reclaim: fix quota stauts loss due to online tunings
MAINTAINERS: mailmap: update Shakeel's email address
mm/damon/sysfs-schemes: handle schemes sysfs dir removal before commit_schemes_quota_goals
mm: memcontrol: clarify swapaccount=0 deprecation warning
mm/memblock: add MEMBLOCK_RSRV_NOINIT into flagname[] array
mm/zswap: invalidate duplicate entry when !zswap_enabled
lib/Kconfig.debug: TEST_IOV_ITER depends on MMU
mm/swap: fix race when skipping swapcache
mm/swap_state: update zswap LRU's protection range with the folio locked
selftests/mm: uffd-unit-test check if huge page size is 0
mm/damon/core: check apply interval in damon_do_apply_schemes()
mm: zswap: fix missing folio cleanup in writeback race path
Linus Torvalds [Fri, 23 Feb 2024 17:23:54 +0000 (09:23 -0800)]
Merge tag 'for-6.8/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Stable fixes for 3 DM targets (integrity, verity and crypt) to
address systemic failure that can occur if user provided pages map to
the same block.
- Fix DM crypt to not allow modifying data that being encrypted for
authenticated encryption.
- Fix DM crypt and verity targets to align their respective bvec_iter
struct members to avoid the need for byte level access (due to
__packed attribute) that is costly on some arches (like RISC).
* tag 'for-6.8/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm-crypt, dm-integrity, dm-verity: bump target version
dm-verity, dm-crypt: align "struct bvec_iter" correctly
dm-crypt: recheck the integrity tag after a failure
dm-crypt: don't modify the data when using authenticated encryption
dm-verity: recheck the hash after a failure
dm-integrity: recheck the integrity tag after a failure
Linus Torvalds [Fri, 23 Feb 2024 17:17:47 +0000 (09:17 -0800)]
Merge tag 'drm-fixes-2024-02-23' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This is the weekly drm fixes. Non-drivers there is a fbdev/sparc fix,
syncobj, ttm and buddy fixes.
On the driver side, ivpu, meson, i915 have a small fix each. Then
amdgpu and xe have a bunch. Nouveau has some minor uapi additions to
give userspace some useful info along with a Kconfig change to allow
the new GSP firmware paths to be used by default on the GPUs it
supports.
Seems about the usual amount for this time of release cycle.
xe:
- Remove support for persistent exec_queues
- Drop a reduntant sysfs newline printout
- A three-patch fix for a VM_BIND rebind optimization path
- Fix a modpost warning on an xe KUNIT module"
* tag 'drm-fixes-2024-02-23' of git://anongit.freedesktop.org/drm/drm: (27 commits)
nouveau: add an ioctl to report vram usage
nouveau: add an ioctl to return vram bar size.
nouveau/gsp: add kconfig option to enable GSP paths by default
drm/amdgpu: Fix the runtime resume failure issue
drm/amd/display: fix null-pointer dereference on edid reading
drm/amd/display: Fix memory leak in dm_sw_fini()
drm/amd/display: fix input states translation error for dcn35 & dcn351
drm/amd/display: Fix potential null pointer dereference in dc_dmub_srv
drm/amd/display: Only allow dig mapping to pwrseq in new asic
drm/amd/display: adjust few initialization order in dm
drm/syncobj: handle NULL fence in syncobj_eventfd_entry_func
drm/syncobj: call drm_syncobj_fence_add_wait when WAIT_AVAILABLE flag is set
drm/ttm: Fix an invalid freeing on already freed page in error path
sparc: Fix undefined reference to fb_is_primary_device
drm/xe: Fix modpost warning on xe_mocs kunit module
drm/xe/xe_gt_idle: Drop redundant newline in name
drm/xe: Return 2MB page size for compact 64k PTEs
drm/xe: Add XE_VMA_PTE_64K VMA flag
drm/xe: Fix xe_vma_set_pte_size
drm/xe/uapi: Remove support for persistent exec_queues
...
Linus Torvalds [Fri, 23 Feb 2024 17:05:56 +0000 (09:05 -0800)]
Merge tag 'ata-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fixes from Niklas Cassel:
- Do not try to set a sleeping device to standby. Sleep is a deeper
sleep state than standby, and needs a reset to wake up the drive. A
system resume will reset the port. Sending a command other than reset
to a sleeping device is not wise, as the command will timeout (Damien
Le Moal)
- Do not try to put a device to standby twice during system shutdown.
ata_dev_power_set_standby() is currently called twice during
shutdown, once after the scsi device is removed, and another when
ata_pci_shutdown_one() executes. Modify ata_dev_power_set_standby()
to do nothing if the device is already in standby (Damien Le Moal)
- Add a quirk for ASM1064 to fixup the number of implemented ports. We
probe all ports that the hardware reports to be implemented. Probing
ports that are not implemented causes significantly increased boot
time (Andrey Jr. Melnikov)
- Fix error handling for the ahci_ceva driver. Ensure that the
ahci_ceva driver does a proper cleanup of its resources in the error
path (Radhey Shyam Pandey)
* tag 'ata-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-core: Do not call ata_dev_power_set_standby() twice
ata: ahci_ceva: fix error handling for Xilinx GT PHY support
ahci: asm1064: correct count of reported ports
ata: libata-core: Do not try to set sleeping devices to standby
Linus Torvalds [Fri, 23 Feb 2024 17:01:35 +0000 (09:01 -0800)]
Merge tag 'gpio-fixes-for-v6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- fix a use-case where no pins are mapped to GPIOs in
gpiochip_generic_config()
* tag 'gpio-fixes-for-v6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: Handle no pin_ranges in gpiochip_generic_config()
Linus Torvalds [Fri, 23 Feb 2024 16:58:47 +0000 (08:58 -0800)]
Merge tag 'hwmon-for-v6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix a global-out-of-bounds bug in nct6775 driver"
* tag 'hwmon-for-v6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (nct6775) Fix access to temperature configuration registers
Jason Gunthorpe [Thu, 22 Feb 2024 14:07:41 +0000 (10:07 -0400)]
iommu/sva: Restore SVA handle sharing
Prior to commit 092edaddb660 ("iommu: Support mm PASID 1:n with sva
domains") the code allowed a SVA handle to be bound multiple times to the
same (mm, device) pair. This was alluded to in the kdoc comment, but we
had understood this to be more a remark about allowing multiple devices,
not a literal same-driver re-opening the same SVA.
It turns out uacce and idxd were both relying on the core code to handle
reference counting for same-device same-mm scenarios. As this looks hard
to resolve in the drivers bring it back to the core code.
The new design has changed the meaning of the domain->users refcount to
refer to the number of devices that are sharing that domain for the same
mm. This is part of the design to lift the SVA domain de-duplication out
of the drivers.
Return the old behavior by explicitly de-duplicating the struct iommu_sva
handle. The same (mm, device) will return the same handle pointer and the
core code will handle tracking this. The last unbind of the handle will
destroy it.
Arnd Bergmann [Fri, 23 Feb 2024 12:54:36 +0000 (13:54 +0100)]
Merge tag 'renesas-fixes-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v6.8
- Add missing #interrupt-cells to DA9063 nodes.
* tag 'renesas-fixes-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: renesas: rcar-gen2: Add missing #interrupt-cells to DA9063 nodes
Arnd Bergmann [Fri, 23 Feb 2024 12:54:07 +0000 (13:54 +0100)]
Merge tag 'riscv-dt-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V Devicetree fixes for v6.8-rc6
Two fixes for W=2 issues in devicetrees, which should constitute fixes
for all reasonable-to-fix W=2 problems on RISC-V. The others are caused
by standard USB and MMC property names containing underscores that are
not likely to ever change.
Signed-off-by: Conor Dooley <[email protected]>
* tag 'riscv-dt-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: sifive: add missing #interrupt-cells to pmic
riscv: dts: starfive: replace underscores in node names
Arnd Bergmann [Fri, 23 Feb 2024 12:53:30 +0000 (13:53 +0100)]
Merge tag 'riscv-cache-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V Cache driver fixes for v6.8-rc6
A single fix for an inconsistency reported during CIP review by Pavel in
the newly added ax45mp cache driver.
Signed-off-by: Conor Dooley <[email protected]>
* tag 'riscv-cache-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
cache: ax45mp_cache: Align end size to cache boundary in ax45mp_dma_cache_wback()
Geoff Levand [Wed, 21 Feb 2024 02:27:29 +0000 (11:27 +0900)]
ps3/gelic: Fix SKB allocation
Commit 3ce4f9c3fbb3 ("net/ps3_gelic_net: Add gelic_descr structures") of
6.8-rc1 had a copy-and-paste error where the pointer that holds the
allocated SKB (struct gelic_descr.skb) was set to NULL after the SKB was
allocated. This resulted in a kernel panic when the SKB pointer was
accessed.
This fix moves the initialization of the gelic_descr to before the SKB
is allocated.
Vladimir Oltean [Tue, 20 Feb 2024 22:34:42 +0000 (00:34 +0200)]
net: dpaa: fman_memac: accept phy-interface-type = "10gbase-r" in the device tree
Since commit 5d93cfcf7360 ("net: dpaa: Convert to phylink"), we support
the "10gbase-r" phy-mode through a driver-based conversion of "xgmii",
but we still don't actually support it when the device tree specifies
"10gbase-r" proper.
This is because boards such as LS1046A-RDB do not define pcs-handle-names
(for whatever reason) in the ethernet@f0000 device tree node, and the
code enters through this code path:
err = of_property_match_string(mac_node, "pcs-handle-names", "xfi");
// code takes neither branch and falls through
if (err >= 0) {
(...)
} else if (err != -EINVAL && err != -ENODATA) {
goto _return_fm_mac_free;
}
(...)
/* For compatibility, if pcs-handle-names is missing, we assume this
* phy is the first one in pcsphy-handle
*/
err = of_property_match_string(mac_node, "pcs-handle-names", "sgmii");
if (err == -EINVAL || err == -ENODATA)
pcs = memac_pcs_create(mac_node, 0); // code takes this branch
else if (err < 0)
goto _return_fm_mac_free;
else
pcs = memac_pcs_create(mac_node, err);
// A default PCS is created and saved in "pcs"
// This determination fails and mistakenly saves the default PCS
// memac->sgmii_pcs instead of memac->xfi_pcs, because at this
// stage, mac_dev->phy_if == PHY_INTERFACE_MODE_10GBASER.
if (err && mac_dev->phy_if == PHY_INTERFACE_MODE_XGMII)
memac->xfi_pcs = pcs;
else
memac->sgmii_pcs = pcs;
In other words, in the absence of pcs-handle-names, the default
xfi_pcs assignment logic only works when in the device tree we have
PHY_INTERFACE_MODE_XGMII.
By reversing the order between the fallback xfi_pcs assignment and the
"xgmii" overwrite with "10gbase-r", we are able to support both values
in the device tree, with identical behavior.
Currently, it is impossible to make the s/xgmii/10gbase-r/ device tree
conversion, because it would break forward compatibility (new device
tree with old kernel). The only way to modify existing device trees to
phy-interface-mode = "10gbase-r" is to fix stable kernels to accept this
value and handle it properly.
One reason why the conversion is desirable is because with pre-phylink
kernels, the Aquantia PHY driver used to warn about the improper use
of PHY_INTERFACE_MODE_XGMII [1]. It is best to have a single (latest)
device tree that works with all supported stable kernel versions.
Note that the blamed commit does not constitute a regression per se.
Older stable kernels like 6.1 still do not work with "10gbase-r", but
for a different reason. That is a battle for another time.
Felix Fietkau [Wed, 21 Feb 2024 14:05:35 +0000 (15:05 +0100)]
wifi: mac80211: only call drv_sta_rc_update for uploaded stations
When a station has not been uploaded yet, receiving SMPS or channel width
notification action frames can lead to rate_control_rate_update calling
drv_sta_rc_update with uninitialized driver private data.
Fix this by adding a missing check for sta->uploaded.
WANG Xuerui [Fri, 23 Feb 2024 06:36:31 +0000 (14:36 +0800)]
LoongArch: KVM: Streamline kvm_check_cpucfg() and improve comments
All the checks currently done in kvm_check_cpucfg can be realized with
early returns, so just do that to avoid extra cognitive burden related
to the return value handling.
While at it, clean up comments of _kvm_get_cpucfg_mask() and
kvm_check_cpucfg(), by removing comments that are merely restatement of
the code nearby, and paraphrasing the rest so they read more natural for
English speakers (that likely are not familiar with the actual Chinese-
influenced grammar).
WANG Xuerui [Fri, 23 Feb 2024 06:36:31 +0000 (14:36 +0800)]
LoongArch: KVM: Rename _kvm_get_cpucfg() to _kvm_get_cpucfg_mask()
The function is not actually a getter of guest CPUCFG, but rather
validation of the input CPUCFG ID plus information about the supported
bit flags of that CPUCFG leaf. So rename it to avoid confusion.
WANG Xuerui [Fri, 23 Feb 2024 06:36:31 +0000 (14:36 +0800)]
LoongArch: KVM: Fix input validation of _kvm_get_cpucfg() & kvm_check_cpucfg()
The range check for the CPUCFG ID is wrong (should have been a ||
instead of &&) and useless in effect, so fix the obvious mistake.
Furthermore, the juggling of the temp return value is unnecessary,
because it is semantically equivalent and more readable to just
return at every switch case's end. This is done too to avoid potential
bugs in the future related to the unwanted complexity.
Also, the return value of _kvm_get_cpucfg is meant to be checked, but
this was not done, so bad CPUCFG IDs wrongly fall back to the default
case and 0 is incorrectly returned; check the return value to fix the
UAPI behavior.
While at it, also remove the redundant range check in kvm_check_cpucfg,
because out-of-range CPUCFG IDs are already rejected by the -EINVAL
as returned by _kvm_get_cpucfg().
The unflatten_and_copy_device_tree() function contains a call to
memblock_alloc(). This means that memblock is allocating memory before
any of the reserved memory regions are set aside in the arch_mem_init()
function which calls early_init_fdt_scan_reserved_mem(). Therefore,
there is a possibility for memblock to allocate from any of the
reserved memory regions.
Hence, move the call to early_init_fdt_scan_reserved_mem() to be earlier
in the init sequence, so that the reserved memory regions are set aside
before any allocations are done using memblock.
Cc: [email protected] Fixes: 88d4d957edc707e ("LoongArch: Add FDT booting support from efi system table") Signed-off-by: Oreoluwa Babatunde <[email protected]> Signed-off-by: Huacai Chen <[email protected]>
Huacai Chen [Fri, 23 Feb 2024 06:36:31 +0000 (14:36 +0800)]
LoongArch: Disable IRQ before init_fn() for nonboot CPUs
Disable IRQ before init_fn() for nonboot CPUs when hotplug, in order to
silence such warnings (and also avoid potential errors due to unexpected
interrupts):
Jeremy Kerr [Tue, 20 Feb 2024 08:10:53 +0000 (16:10 +0800)]
net: mctp: take ownership of skb in mctp_local_output
Currently, mctp_local_output only takes ownership of skb on success, and
we may leak an skb if mctp_local_output fails in specific states; the
skb ownership isn't transferred until the actual output routing occurs.
Instead, make mctp_local_output free the skb on all error paths up to
the route action, so it always consumes the passed skb.
Jakub Kicinski [Fri, 23 Feb 2024 03:19:37 +0000 (19:19 -0800)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-20 (ice)
This series contains updates to ice driver only.
Yochai sets parent device to properly reflect connection state between
source DPLL and output pin.
Arkadiusz fixes additional issues related to DPLL; proper reporting of
phase_adjust value and preventing use/access of data while resetting.
Amritha resolves ASSERT_RTNL() being triggered on certain reset/rebuild
flows.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix ASSERT_RTNL() warning during certain scenarios
ice: fix pin phase adjust updates on PF reset
ice: fix dpll periodic work data updates on PF reset
ice: fix dpll and dpll_pin data access on PF reset
ice: fix dpll input pin phase_adjust value updates
ice: fix connection state of DPLL and out pin
====================
The splat occurs because skb->data points past skb->head allocated area.
This is because neigh layer does:
__skb_pull(skb, skb_network_offset(skb));
... but skb_network_offset() returns a negative offset and __skb_pull()
arg is unsigned. IOW, we skb->data gets "adjusted" by a huge value.
The negative value is returned because skb->head and skb->data distance is
more than 64k and skb->network_header (u16) has wrapped around.
The bug is in the ip_tunnel infrastructure, which can cause
dev->needed_headroom to increment ad infinitum.
The syzkaller reproducer consists of packets getting routed via a gre
tunnel, and route of gre encapsulated packets pointing at another (ipip)
tunnel. The ipip encapsulation finds gre0 as next output device.
This results in the following pattern:
1). First packet is to be sent out via gre0.
Route lookup found an output device, ipip0.
2).
ip_tunnel_xmit for gre0 bumps gre0->needed_headroom based on the future
output device, rt.dev->needed_headroom (ipip0).
3).
ip output / start_xmit moves skb on to ipip0. which runs the same
code path again (xmit recursion).
4).
Routing step for the post-gre0-encap packet finds gre0 as output device
to use for ipip0 encapsulated packet.
tunl0->needed_headroom is then incremented based on the (already bumped)
gre0 device headroom.
This repeats for every future packet:
gre0->needed_headroom gets inflated because previous packets' ipip0 step
incremented rt->dev (gre0) headroom, and ipip0 incremented because gre0
needed_headroom was increased.
For each subsequent packet, gre/ipip0->needed_headroom grows until
post-expand-head reallocations result in a skb->head/data distance of
more than 64k.
Once that happens, skb->network_header (u16) wraps around when
pskb_expand_head tries to make sure that skb_network_offset() is unchanged
after the headroom expansion/reallocation.
After this skb_network_offset(skb) returns a different (and negative)
result post headroom expansion.
The next trip to neigh layer (or anything else that would __skb_pull the
network header) makes skb->data point to a memory location outside
skb->head area.
v2: Cap the needed_headroom update to an arbitarily chosen upperlimit to
prevent perpetual increase instead of dropping the headroom increment
completely.
Ryosuke Yasuoka [Wed, 21 Feb 2024 07:40:48 +0000 (16:40 +0900)]
netlink: Fix kernel-infoleak-after-free in __skb_datagram_iter
syzbot reported the following uninit-value access issue [1]:
netlink_to_full_skb() creates a new `skb` and puts the `skb->data`
passed as a 1st arg of netlink_to_full_skb() onto new `skb`. The data
size is specified as `len` and passed to skb_put_data(). This `len`
is based on `skb->end` that is not data offset but buffer offset. The
`skb->end` contains data and tailroom. Since the tailroom is not
initialized when the new `skb` created, KMSAN detects uninitialized
memory area when copying the data.
This patch resolved this issue by correct the len from `skb->end` to
`skb->len`, which is the actual data offset.
projects / linux.git / log