Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes before final release:
Marvell Armada:
- One to fix a typo in the devicetree specifying memory ranges for
the crypto engine
- Two to deal with marking PCI and device-memory as strongly ordered
to avoid hardware deadlocks, in particular when enabling above
crypto driver.
- Compile fix for PM
Allwinner:
- DT clock fixes to deal with u-boot-enabled framebuffer (simplefb).
- Make R8 (C.H.I.P. SoC) inherit system compatibility from A13 to
make clocks register proper.
Tegra:
- Fix SD card voltage setting on the Tegra3 Beaver dev board
Misc:
- Two maintainers updates for STM32 and STi platforms"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: beaver: Allow SD card voltage to be changed
MAINTAINERS: update STi maintainer list
MAINTAINERS: update STM32 maintainers list
ARM: mvebu: compile pm code conditionally
ARM: dts: sun7i: Fix pll3x2 and pll7x2 not having a parent clock
ARM: dts: sunxi: Add pll3 to simplefb nodes clocks lists
ARM: dts: armada-38x: fix MBUS_ID for crypto SRAM on Armada 385 Linksys
ARM: mvebu: map PCI I/O regions strongly ordered
ARM: mvebu: fix HW I/O coherency related deadlocks
ARM: sunxi/dt: make the CHIP inherit from allwinner,sun5i-a13
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull key handling fixes from James Morris:
"Quoting David Howells:
Here are three miscellaneous fixes:
(1) Fix a panic in some debugging code in PKCS#7. This can only
happen by explicitly inserting a #define DEBUG into the code.
(2) Fix the calculation of the digest length in the PE file parser.
This causes a failure where there should be a success.
(3) Fix the case where an X.509 cert can be added as an asymmetric key
to a trusted keyring with no trust restriction if no AKID is
supplied.
Bugs (1) and (2) aren't particularly problematic, but (3) allows a
security check to be bypassed. Happily, this is a recent regression
and never made it into a released kernel"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: Fix for erroneous trust of incorrectly signed X.509 certs
pefile: Fix the failure of calculation for digest
PKCS#7: Fix panic when referring to the empty AKID when DEBUG defined
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A few more fixes for the input subsystem:
- restore naming for tsc2005 touchscreens as some userspace match on it
- fix out of bound access in legacy keyboard driver
- fixup in RMI4 driver
Everything is tagged for stable as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc200x - report proper input_dev name
tty/vt/keyboard: fix OOB access in do_compute_shiftstate()
Input: synaptics-rmi4 - fix maximum size check for F12 control register 8
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Dan Williams:
"This contains a regression fix for a problem that was introduced in
v4.7-rc6.
In 4.7-rc1 we introduced auto-probing for the ACPI DSM (device-
specific-method) format that the platform firmware implements for
nvdimm devices. We initially fixed a regression in probing the QEMU
DSM implementation by making acpi_check_dsm() tolerant of the way QEMU
reports the "0 DSMs supported" condition.
However, that broke HPE platforms since that tolerance caused the
driver to mistakenly match the 1-zero-byte response those platforms
give to "unknown" commands. Instead, we simply make the driver
tolerant of not finding any supported DSMs. This has been tested to
work with both QEMU and HPE platforms.
This commit has appeared in a -next release with no reported issues"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: make DIMM DSMs optional
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"Fix a bug in the at91 clk driver, two compile time warnings in sunxi
clk drivers, and one bug in a sunxi clk driver introduced in the 4.7
merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: fix clk_programmable_set_parent()
clk: sunxi: remove unused variable
clk: sunxi: display: Add per-clock flags
clk: sunxi: tcon-ch1: Do not return a negative error in get_parent
Merge tag 'sound-4.7-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No surprise, just a few small fixes: a couple of changes are seen in
the core part, and both of them are rather for unusual error paths.
The rest are the regular HD-audio fixes and one USB-audio regression
fix"
* tag 'sound-4.7-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix quirks code is not called
ALSA: hda: add AMD Stoney PCI ID with proper driver caps
ALSA: hda - fix use-after-free after module unload
ALSA: pcm: Free chmap at PCM free callback, too
ALSA: ctl: Stop notification after disconnection
ALSA: hda/realtek - add new pin definition in alc225 pin quirk table
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull NVMe fix from Jens Axboe:
"Late addition here, it's basically a revert of a patch that was added
in this merge window, but has proven to cause problems.
This is swapping out the RCU based namespace protection with a good
old mutex instead"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: Remove RCU namespace protection
radix-tree: fix radix_tree_iter_retry() for tagged iterators.
radix_tree_iter_retry() resets slot to NULL, but it doesn't reset tags.
Then NULL slot and non-zero iter.tags passed to radix_tree_next_slot()
leading to crash:
Johannes Weiner [Wed, 20 Jul 2016 22:44:57 +0000 (15:44 -0700)]
mm: memcontrol: fix cgroup creation failure after many small jobs
The memory controller has quite a bit of state that usually outlives the
cgroup and pins its CSS until said state disappears. At the same time
it imposes a 16-bit limit on the CSS ID space to economically store IDs
in the wild. Consequently, when we use cgroups to contain frequent but
small and short-lived jobs that leave behind some page cache, we quickly
run into the 64k limitations of outstanding CSSs. Creating a new cgroup
fails with -ENOSPC while there are only a few, or even no user-visible
cgroups in existence.
Although pinning CSSs past cgroup removal is common, there are only two
instances that actually need an ID after a cgroup is deleted: cache
shadow entries and swapout records.
Cache shadow entries reference the ID weakly and can deal with the CSS
having disappeared when it's looked up later. They pose no hurdle.
Swap-out records do need to pin the css to hierarchically attribute
swapins after the cgroup has been deleted; though the only pages that
remain swapped out after offlining are tmpfs/shmem pages. And those
references are under the user's control, so they are manageable.
This patch introduces a private 16-bit memcg ID and switches swap and
cache shadow entries over to using that. This ID can then be recycled
after offlining when the CSS remains pinned only by objects that don't
specifically need it.
This script demonstrates the problem by faulting one cache page in a new
cgroup and deleting it again:
set -e
mkdir -p pages
for x in `seq 128000`; do
[ $((x % 1000)) -eq 0 ] && echo $x
mkdir /cgroup/foo
echo $$ >/cgroup/foo/cgroup.procs
echo trex >pages/$x
echo $$ >/cgroup/cgroup.procs
rmdir /cgroup/foo
done
When run on an unpatched kernel, we eventually run out of possible IDs
even though there are no visible cgroups:
[root@ham ~]# ./cssidstress.sh
[...]
65000
mkdir: cannot create directory '/cgroup/foo': No space left on device
After this patch, the IDs get released upon cgroup destruction and the
cache and css objects get released once memory reclaim kicks in.
I stumbled over a build error with COMPILE_TEST and CONFIG_OF
disabled:
drivers/gpio/gpio-tegra.c: In function 'tegra_gpio_probe':
drivers/gpio/gpio-tegra.c:603:9: error: 'struct gpio_chip' has no member named 'of_node'
The problem is that the newly added GPIO_TEGRA Kconfig symbol
does not have a dependency on CONFIG_OF. However, there is another
problem here as the driver gets enabled unconditionally whenever
COMPILE_TEST is set.
This fixes both problems, by making the symbol user-visible
when COMPILE_TEST is set and default-enabled for ARCH_TEGRA=y.
As a side-effect, it is now possible to compile-test a Tegra
kernel with GPIO support disabled, which is harmless.
libceph: apply new_state before new_up_client on incrementals
Currently, osd_weight and osd_state fields are updated in the encoding
order. This is wrong, because an incremental map may look like e.g.
new_up_client: { osd=6, addr=... } # set osd_state and addr
new_state: { osd=6, xorstate=EXISTS } # clear osd_state
Suppose osd6's current osd_state is EXISTS (i.e. osd6 is down). After
applying new_up_client, osd_state is changed to EXISTS | UP. Carrying
on with the new_state update, we flip EXISTS and leave osd6 in a weird
"!EXISTS but UP" state. A non-existent OSD is considered down by the
mapping code
2087 for (i = 0; i < pg->pg_temp.len; i++) {
2088 if (ceph_osd_is_down(osdmap, pg->pg_temp.osds[i])) {
2089 if (ceph_can_shift_osds(pi))
2090 continue;
2091
2092 temp->osds[temp->size++] = CRUSH_ITEM_NONE;
and so requests get directed to the second OSD in the set instead of
the first, resulting in OSD-side errors like:
[WRN] : client.4239 192.168.122.21:0/2444980242 misdirected client.4239.1:2827 pg 2.5df899f2 to osd.4 not [1,4,6] in e680/680
and hung rbds on the client:
[ 493.566367] rbd: rbd0: write 400000 at 11cc00000 (0)
[ 493.566805] rbd: rbd0: result -6 xferred 400000
[ 493.567011] blk_update_request: I/O error, dev rbd0, sector 9330688
The fix is to decouple application from the decoding and:
- apply new_weight first
- apply new_state before new_up_client
- twiddle osd_state flags if marking in
- clear out some of the state if osd is destroyed
Andy Lutomirski [Thu, 21 Jul 2016 21:16:52 +0000 (14:16 -0700)]
x86/boot: Simplify EBDA-vs-BIOS reservation logic
Both the intent and the effect of reserve_bios_regions() is simple:
reserve the range from the apparent BIOS start (suitably filtered)
through 1MB and, if the EBDA start address is sensible, extend that
reservation downward to cover the EBDA as well.
The code is overcomplicated, though, and contains head-scratchers
like:
if (ebda_start < BIOS_START_MIN)
ebda_start = BIOS_START_MAX;
That snipped is trying to say "if ebda_start < BIOS_START_MIN,
ignore it".
Simplify it: reorder the code so that it makes sense. This should
have no functional effect under any circumstances.
ovl: verify upper dentry in ovl_remove_and_whiteout()
The upper dentry may become stale before we call ovl_lock_rename_workdir.
For example, someone could (mistakenly or maliciously) manually unlink(2)
it directly from upperdir.
To ensure it is not stale, let's lookup it after ovl_lock_rename_workdir
and and check if it matches the upper dentry.
Essentially, it is the same problem and similar solution as in
commit 11f3710417d0 ("ovl: verify upper dentry before unlink and rename").
sock_cmsg_send() can return different error codes and not only
-EINVAL, and we should properly propagate them.
Fixes: c14ac9451c34 ("sock: enable timestamping using control messages") Signed-off-by: Soheil Hassas Yeganeh <[email protected]> Cc: Willem de Bruijn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Bob Peterson [Thu, 21 Jul 2016 18:02:44 +0000 (13:02 -0500)]
GFS2: Fix gfs2_replay_incr_blk for multiple journal sizes
Before this patch, if you used gfs2_jadd to add new journals of a
size smaller than the existing journals, replaying those new journals
would withdraw. That's because function gfs2_replay_incr_blk was
using the number of journal blocks (jd_block) from the superblock's
journal pointer. In other words, "My journal's max size" rather than
"the journal we're replaying's size." This patch changes the function
to use the size of the pertinent journal rather than always using the
journal we happen to be using.
Dave Hansen [Wed, 20 Jul 2016 19:45:51 +0000 (12:45 -0700)]
x86/fpu: Do not BUG_ON() in early FPU code
I don't think it is really possible to have a system where CPUID
enumerates support for XSAVE but that it does not have FP/SSE
(they are "legacy" features and always present).
But, I did manage to hit this case in qemu when I enabled its
somewhat shaky XSAVE support. The bummer is that the FPU is set
up before we parse the command-line or have *any* console support
including earlyprintk. That turned what should have been an easy
thing to debug in to a bit more of an odyssey.
So a BUG() here is worthless. All it does it guarantee that
if/when we hit this case we have an empty console. So, remove
the BUG() and try to limp along by disabling XSAVE and trying to
continue. Add a comment on why we are doing this, and also add
a common "out_disable" path for leaving fpu__init_system_xstate().
x86/boot: Reorganize and clean up the BIOS area reservation code
So the reserve_ebda_region() code has accumulated a number of
problems over the years that make it really difficult to read
and understand:
- The calculation of 'lowmem' and 'ebda_addr' is an unnecessarily
interleaved mess of first lowmem, then ebda_addr, then lowmem tweaks...
- 'lowmem' here means 'super low mem' - i.e. 16-bit addressable memory. In other
parts of the x86 code 'lowmem' means 32-bit addressable memory... This makes it
super confusing to read.
- It does not help at all that we have various memory range markers, half of which
are 'start of range', half of which are 'end of range' - but this crucial
property is not obvious in the naming at all ... gave me a headache trying to
understand all this.
- Also, the 'ebda_addr' name sucks: it highlights that it's an address (which is
obvious, all values here are addresses!), while it does not highlight that it's
the _start_ of the EBDA region ...
- 'BIOS_LOWMEM_KILOBYTES' says a lot of things, except that this is the only value
that is a pointer to a value, not a memory range address!
- The function name itself is a misnomer: it says 'reserve_ebda_region()' while
its main purpose is to reserve all the firmware ROM typically between 640K and
1MB, while the 'EBDA' part is only a small part of that ...
- Likewise, the paravirt quirk flag name 'ebda_search' is misleading as well: this
too should be about whether to reserve firmware areas in the paravirt case.
- In fact thinking about this as 'end of RAM' is confusing: what this function
*really* wants to reserve is firmware data and code areas! Once the thinking is
inverted from a mixed 'ram' and 'reserved firmware area' notion to a pure
'reserved area' notion everything becomes a lot clearer.
To improve all this rewrite the whole code (without changing the logic):
- Firstly invert the naming from 'lowmem end' to 'BIOS reserved area start'
and propagate this concept through all the variable names and constants.
- Then clean up the name of the function itself by renaming it
to reserve_bios_regions() and renaming the ::ebda_search paravirt
flag to ::reserve_bios_regions.
- Fix up all the comments (fix typos), harmonize and simplify their
formulation and remove comments that become unnecessary due to
the much better naming all around.
Jan Stancek [Thu, 30 Jun 2016 10:23:51 +0000 (12:23 +0200)]
crypto: qat - make qat_asym_algs.o depend on asn1 headers
Parallel build can sporadically fail because asn1 headers may
not be built yet by the time qat_asym_algs.o is compiled:
drivers/crypto/qat/qat_common/qat_asym_algs.c:55:32: fatal error: qat_rsapubkey-asn1.h: No such file or directory
#include "qat_rsapubkey-asn1.h"
Michael Welling [Wed, 20 Jul 2016 17:02:07 +0000 (10:02 -0700)]
Input: tsc200x - report proper input_dev name
Passes input_id struct to the common probe function for the tsc200x drivers
instead of just the bustype.
This allows for the use of the product variable to set the input_dev->name
variable according to the type of touchscreen used. Note that when we
introduced support for TSC2004 we started calling everything TSC200X, so
let's keep this quirk.
Dmitry Torokhov [Mon, 27 Jun 2016 21:12:34 +0000 (14:12 -0700)]
tty/vt/keyboard: fix OOB access in do_compute_shiftstate()
The size of individual keymap in drivers/tty/vt/keyboard.c is NR_KEYS,
which is currently 256, whereas number of keys/buttons in input device (and
therefor in key_down) is much larger - KEY_CNT - 768, and that can cause
out-of-bound access when we do
sym = U(key_maps[0][k]);
with large 'k'.
To fix it we should not attempt iterating beyond smaller of NR_KEYS and
KEY_CNT.
Also while at it let's switch to for_each_set_bit() instead of open-coding
it.
net/mlx5e: Fix del vxlan port command buffer memset
memset the command buffers rather than the pointers to them.
Fixes: b3f63c3d5e2c ("net/mlx5e: Add netdev support for VXLAN tunneling") Signed-off-by: Saeed Mahameed <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Michael Walle [Tue, 19 Jul 2016 14:43:26 +0000 (16:43 +0200)]
hwmon: (adt7411) set bit 3 in CFG1 register
According to the datasheet you should only write 1 to this bit. If it is
not set, at least AIN3 will return bad values on newer silicon revisions.
Fixes: d84ca5b345c2 ("hwmon: Add driver for ADT7411 voltage and temperature sensor") Signed-off-by: Michael Walle <[email protected]> Signed-off-by: Guenter Roeck <[email protected]>
packet: fix second argument of sock_tx_timestamp()
This patch fixes an issue that a syscall (e.g. sendto syscall) cannot
work correctly. Since the sendto syscall doesn't have msg_control buffer,
the sock_tx_timestamp() in packet_snd() cannot work correctly because
the socks.tsflags is set to 0.
So, this patch sets the socks.tsflags to sk->sk_tsflags as default.
Andrew Duggan [Wed, 20 Jul 2016 00:53:59 +0000 (17:53 -0700)]
Input: synaptics-rmi4 - fix maximum size check for F12 control register 8
According to the RMI4 spec the maximum size of F12 control register 8 is
15 bytes. The current code incorrectly reports an error if control 8 is
greater then 14. Making sensors with a control register 8 with 15 bytes
unusable.
Vivien Didelot [Mon, 18 Jul 2016 19:02:06 +0000 (15:02 -0400)]
net: switchdev: change ageing_time type to clock_t
The switchdev value for the SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME
attribute is a clock_t and requires to use helpers such as
clock_t_to_jiffies() to convert to milliseconds.
Change ageing_time type from u32 to clock_t to make it explicit.
Fixes: f55ac58ae64c ("switchdev: add bridge ageing_time attribute") Signed-off-by: Vivien Didelot <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Douglas Miller [Mon, 18 Jul 2016 17:28:45 +0000 (12:28 -0500)]
Update maintainer for EHEA driver.
Since Thadeu left IBM, EHEA has gone mostly unmaintained, since his email
address doesn't work anymore. I'm stepping up to help maintain this
driver upstream.
I'm adding Thadeu's personal e-mail address in Cc, hoping that we can
get his ack.
David S. Miller [Tue, 19 Jul 2016 23:44:12 +0000 (16:44 -0700)]
Merge branch 'mlx4-fixes'
Tariq Toukan says:
====================
Safe flow for mlx4_en configuration change
This patchset improves the mlx4_en driver resiliency, especially on
systems with low memory. Upon a configuration change that requires
the allocation of new resources, we first try to allocate, prior to
destroying the current ones. Once it is successfully done,
we release the old resources and attach the new ones. Otherwise, we
stay with a functioning interface having the same old configuration.
This improvement became of greater significance after removing the use
of vmap.
====================
This patch fixes the lost of Ethernet port on low memory system,
when driver frees its resources and fails to allocate new resources.
Issue could happen while changing number of channels, rings size or
changing the timestamp configuration.
This fix is necessary because of removing vmap use in the code.
When vmap was in use driver could allocate non-contiguous memory
and make it contiguous with vmap. Now it could fail to allocate
a large chunk of contiguous memory and lose the port.
Current code tries to allocate new resources and then upon success
frees the old resources.
Fixes: 73898db04301 ('net/mlx4: Avoid wrong virtual mappings') Signed-off-by: Eugenia Emantayev <[email protected]> Signed-off-by: Tariq Toukan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Dan Williams [Tue, 19 Jul 2016 19:32:39 +0000 (12:32 -0700)]
nfit: make DIMM DSMs optional
Commit 4995734e973a "acpi, nfit: fix acpi_check_dsm() vs zero functions
implemented" attempted to fix a QEMU regression by supporting its usage
of a zero-mask as a valid response to a DSM-family probe request.
However, this behavior breaks HP platforms that return a zero-mask by
default causing the probe to misidentify the DSM-family.
Instead, the QEMU regression can be fixed by simply not requiring the DSM
family to be identified.
This effectively reverts commit 4995734e973a, and removes the DSM
requirement from the init path.
tick_nohz_start_idle is called before checking whether the idle tick can be
stopped. If the tick cannot be stopped, calling tick_nohz_start_idle() is
pointless and just wasting CPU cycles.
Only invoke tick_nohz_start_idle() when can_stop_idle_tick() returns true. A
short one minute observation of the effect on ARM64 shows a reduction of calls
by 1.5% thus optimizing the idle entry sequence.
Vincent Stehle [Mon, 18 Jul 2016 20:56:26 +0000 (22:56 +0200)]
genirq: Fix missing irq allocation affinity hint
The new affinity hint argument of __irq_domain_alloc_irqs() is missing in
irq_reserve_ipi(). Add it.
This fixes the following compilation error:
kernel/irq/ipi.c: In function ‘irq_reserve_ipi’:
kernel/irq/ipi.c:85:9: error: too few arguments to function ‘__irq_domain_alloc_irqs’
virq = __irq_domain_alloc_irqs(domain, virq, nr_irqs, NUMA_NO_NODE,
^ Fixes: 06ee6d571f0e ("genirq: Add affinity hint to irq allocation") Signed-off-by: Vincent Stehlé <[email protected]> Cc: [email protected] Cc: Christoph Hellwig <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]>
Ben Dooks [Fri, 17 Jun 2016 15:56:14 +0000 (16:56 +0100)]
clockevents: Make clockevents_subsys static
The clockevents_subsys struct is used for sysfs support and
is not declared or used outside the file it is defined in.
Fix the following warning by making it static:
kernel/time/clockevents.c:648:17: warning: symbol 'clockevents_subsys' was not declared. Should it be static?
Dave Airlie [Tue, 19 Jul 2016 08:00:15 +0000 (18:00 +1000)]
Merge tag 'topic/kbl-4.7-fixes-2016-07-18' of git://anongit.freedesktop.org/drm-intel into drm-fixes
As promised here's the pile of kbl cherry-picks assembled by Mika&Rodrigo.
It's a bit much, but all well-contained to kbl code and been tested for a
while in drm-intel-next. Still separate in case too much, but in that case
I think we'd need to disable kbl by default again (which would be annoying
too) in 4.7.
* tag 'topic/kbl-4.7-fixes-2016-07-18' of git://anongit.freedesktop.org/drm-intel: (28 commits)
drm/i915/kbl: Introduce the first official DMC for Kabylake.
drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.
drm/i915/gen9: implement WaConextSwitchWithConcurrentTLBInvalidate
drm/i915/gen9: Add WaFbcHighMemBwCorruptionAvoidance
drm/i195/fbc: Add WaFbcNukeOnHostModify
drm/i915/gen9: Add WaFbcWakeMemOn
drm/i915/gen9: Add WaFbcTurnOffFbcWatermark
drm/i915/kbl: Add WaClearSlmSpaceAtContextSwitch
drm/i915/gen9: Add WaEnableChickenDCPR
drm/i915/kbl: Add WaDisableSbeCacheDispatchPortSharing
drm/i915/kbl: Add WaDisableGafsUnitClkGating
drm/i915/kbl: Add WaForGAMHang
drm/i915: Add WaInsertDummyPushConstP for bxt and kbl
drm/i915/kbl: Add WaDisableDynamicCreditSharing
drm/i915/kbl: Add WaDisableGamClockGating
drm/i915/gen9: Enable must set chicken bits in config0 reg
drm/i915/kbl: Add WaDisableLSQCROPERFforOCL
drm/i915/kbl: Add WaDisableSDEUnitClockGating
drm/i915/kbl: Add WaDisableFenceDestinationToSLM for A0
drm/i915/kbl: Add WaEnableGapsTsvCreditFix
...
Merge tag 'perf-core-for-mingo-20160718' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- Properly report when a function wildcard produces no matches in 'perf probe'
(Masami Hiramatsu)
- Balance opening and reading events in 'perf stat', which could cause
it to get stuck trying to close invalid file descriptors (Mark Rutland)
Infrastructure changes:
- Copy more headers from the kernel, this time for headers that
were just including the contents of its kernel counterparts, should
help resolving the problems with linux-next, where some uapi related
patches seem to be breaking tools/object/ build. (Arnaldo Carvalho de Melo)
Some more combing will be done, but at least it is possible to build
perf out of tree, via a detached tarball (make help | grep perf),
without including kernel files in its MANIFEST (Arnaldo Carvalho de Melo)
- Fix smatch found errors that were not causing problems, but are
mistakes nonetheless (Dan Carpenter)
- Fix string vs. byte array resolving in the python script code (Jiri Olsa)
Dave Airlie [Tue, 19 Jul 2016 06:09:20 +0000 (16:09 +1000)]
Merge tag 'drm-intel-fixes-2016-07-18' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Two more regression fixes for 4.7.
* tag 'drm-intel-fixes-2016-07-18' of git://anongit.freedesktop.org/drm-intel:
drm/i915: add missing condition for committing planes on crtc
drm/i915: Treat eDP as always connected, again
net/sched/sch_htb: clamp xstats tokens to fit into 32-bit int
In kernel HTB keeps tokens in signed 64-bit in nanoseconds. In netlink
protocol these values are converted into pshed ticks (64ns for now) and
truncated to 32-bit. In struct tc_htb_xstats fields "tokens" and "ctokens"
are declared as unsigned 32-bit but they could be negative thus tool 'tc'
prints them as signed. Big values loose higher bits and/or become negative.
This patch clamps tokens in xstat into range from INT_MIN to INT_MAX.
In this way it's easier to understand what's going on here.
Boris Brezillon [Mon, 18 Jul 2016 07:49:12 +0000 (09:49 +0200)]
clk: at91: fix clk_programmable_set_parent()
Since commit 1bdf02326b71e ("clk: at91: make use of syscon/regmap
internally"), clk_programmable_set_parent() is always selecting the
first parent (AKA slow_clk), no matter what's passed in the 'index'
parameter.
Fix that by initializing the pckr variable to the index value.
Jiri Olsa [Sat, 16 Jul 2016 16:11:18 +0000 (18:11 +0200)]
perf script python: Fix string vs byte array resolving
Jirka reported that python code returns all arrays as strings. This
makes impossible to get all items for byte array tracepoint field
containing 0x00 value item.
Fixing this by scanning full length of the array and returning it as
PyByteArray object in case non printable byte is found.
perf probe: Warn unmatched function filter correctly
Warn unmatched function filter correctly instead of warning
"symbol-loading error", since that can be a filter issue.
From the technical point of view, this adds a filter chech in map__load
and if there is a filter, it returns -2 (filter-out), instead of -1
(error), and perf-probe checks it and change message.
E.g. without this fix:
# perf probe -F rt_sp*
no symbols found in [kernel.kallsyms], maybe install a debug package?
Failed to load symbols in kernel
With this fix:
# perf probe -F rt_sp*
no symbols passed the given filter.
Failed to find symbols matched to "rt_sp*"
Error: Failed to show functions.
Mark Rutland [Fri, 15 Jul 2016 10:08:11 +0000 (11:08 +0100)]
perf cpu_map: Add more helpers
In some cases it's necessry to figure out the map-local index of a given
Linux logical CPU ID. Add a new helper, cpu_map__idx, to acquire this.
As the logic is largely the same as the existing cpu_map__has, this is
rewritten in terms of the new helper.
At the same time, add the inverse operation, cpu_map__cpu, which yields
the logical CPU id for a map-local index. While this can be performed
manually, wrapping this in a helper can make code more legible.
Mark Rutland [Fri, 15 Jul 2016 10:08:10 +0000 (11:08 +0100)]
perf stat: Balance opening and reading events
In create_perf_stat_counter, when a target CPU has not been provided, we
call __perf_evsel__open with empty_cpu_map, and open a single FD per
thread. However, in read_counter we assume that we opened events for the
product of threads and CPUs described in the evsel's cpu_map.
Thus, if an evsel has a cpu_map with more than one entry, we will
attempt to access FDs that we didn't open. This could result in a number
of problems (e.g. blocking while reading from STDIN if the fd memory
happened to be initialised to zero).
This is problematic for systems were a logical CPU PMU covers some
arbitrary subset of CPUs. The cpu_map of any evsel for that PMU will be
initialised based on the cpumask exposed through sysfs, even if the user
requests per-thread events.
Since 34b48db66e08 ("block: remove artifical max_hw_sectors cap"),
max_sectors is no longer limited to BLK_DEF_MAX_SECTORS and LITE-ON
CX1-JB256-HP keeps timing out with higher max_sectors. Revert it to
the previous value.
Dan Carpenter [Fri, 15 Jul 2016 21:08:36 +0000 (00:08 +0300)]
perf jit: Remove some no-op error handling
The 'info.e_machine' struct member is an uint16_t so 'm' is never less
than zero. It looks like this was maybe left over code from earlier
versions so I've just removed it.
drm/i915: add missing condition for committing planes on crtc
The i915 driver checks for color management properties changes as part
of a plane update. Therefore a color management update must imply a
plane update, otherwise we never update the transformation matrixes
and degamma/gamma LUTs.
v2: add comment about moving the commit of color management registers
to an async worker
v3: Commit color management register right after vblank
v4: Move back color management commit condition together with planes
commit
v5: Trigger color management commit through the planes commit (Daniel)
Ville Syrjälä [Mon, 18 Jul 2016 10:15:14 +0000 (13:15 +0300)]
drm/i915: Treat eDP as always connected, again
eDP should be treated as connected even if doesn't have an EDID. In that
case we'll use the timings from the VBT. That used to be the case until
commit f21a21983ef1 ("drm/i915: Splitting intel_dp_detect")
broke things by considering even eDP disconnected if we fail to get
an EDID for it.
Fix things up again by treating eDP as always connected.
snd_usb_{set_interface,ctl_msg}_quirk checks chip->usb_id to need
calling a quirks code. But existed code path that not calling
dev_set_drvdata in usb_audio_probe.
Robert Jarzmik [Thu, 14 Jul 2016 15:05:50 +0000 (17:05 +0200)]
mmc: pxamci: fix potential oops
As reported by Dan in his report in [1], there is a potential NULL
pointer derefence if these conditions are met :
- there is no platform_data provided, ie. host->pdata = NULL
Fix this by only using the platform data ro_invert when a gpio for
read-only is provided by the platform data.
This doesn't appear yet as every pxa board provides a platform_data, and
calls pxa_set_mci_info() with a non NULL pointer.
[1] [bug report] mmc: pxamci: fix card detect with slot-gpio API.
The commit fd546ee6a7dc ("mmc: pxamci: fix card detect with slot-gpio
API") from Sep 26, 2015, leads to the following static checker warning:
drivers/mmc/host/pxamci.c:809 pxamci_probe()
warn: variable dereferenced before check 'host->pdata' (see line 798)
Fixes: fd546ee6a7dc ("mmc: pxamci: fix card detect with slot-gpio API") Reported-by: Dan Carpenter <[email protected]> Signed-off-by: Robert Jarzmik <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>
The code that fills packed command header assumes that CPU runs in
little-endian mode. Hence the header is malformed in big-endian mode
and causes MMC data transfer errors:
[ 563.200828] mmcblk0: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc40
[ 563.219647] mmcblk0: packed cmd failed, nr 2, sectors 16, failure index: -1
Ville Viinikka [Fri, 8 Jul 2016 15:27:02 +0000 (18:27 +0300)]
mmc: block: fix free of uninitialized 'idata->buf'
Set 'idata->buf' to NULL so that it never gets returned without
initialization. This fixes a bug where mmc_blk_ioctl_cmd() would
free both 'idata' and 'idata->buf' but 'idata->buf' was returned
uninitialized.
Fixes: 1ff8950c0433 ("mmc: block: change to use kmalloc when copy data from userspace") Signed-off-by: Ville Viinikka <[email protected]> Cc: <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>
Mat Martineau [Sun, 17 Jul 2016 23:10:55 +0000 (00:10 +0100)]
KEYS: Fix for erroneous trust of incorrectly signed X.509 certs
Arbitrary X.509 certificates without authority key identifiers (AKIs)
can be added to "trusted" keyrings, including IMA or EVM certs loaded
from the filesystem. Signature verification is currently bypassed for
certs without AKIs.
Trusted keys were recently refactored, and this bug is not present in
4.6.
restrict_link_by_signature should return -ENOKEY (no matching parent
certificate found) if the certificate being evaluated has no AKIs,
instead of bypassing signature checks and returning 0 (new certificate
accepted).
net: cavium: liquidio: Avoid dma_unmap_single on uninitialized ndata
The label lio_xmit_failed is used 3 times through liquidio_xmit() but it
always makes a call to dma_unmap_single() using potentially
uninitialized variables from "ndata" variable. Out of the 3 gotos, 2 run
after ndata has been initialized, and had a prior dma_map_single() call.
Fix this by adding a new error label: lio_xmit_dma_failed which does
this dma_unmap_single() and then processed with the lio_xmit_failed
fallthrough.
Fixes: f21fb3ed364bb ("Add support of Cavium Liquidio ethernet adapters") Reported-by: coverity (CID 1309740) Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Paolo Abeni [Thu, 14 Jul 2016 16:00:10 +0000 (18:00 +0200)]
vlan: use a valid default mtu value for vlan over macsec
macsec can't cope with mtu frames which need vlan tag insertion, and
vlan device set the default mtu equal to the underlying dev's one.
By default vlan over macsec devices use invalid mtu, dropping
all the large packets.
This patch adds a netif helper to check if an upper vlan device
needs mtu reduction. The helper is used during vlan devices
initialization to set a valid default and during mtu updating to
forbid invalid, too bit, mtu values.
The helper currently only check if the lower dev is a macsec device,
if we get more users, we need to update only the helper (possibly
reserving an additional IFF bit).
Hans de Goede [Thu, 30 Jun 2016 17:12:32 +0000 (12:12 -0500)]
usb: musb: sunxi: Simplify dr_mode handling
phy-sun4i-usb now has proper dr_mode handling, it always registers an
extcon, and sends a notify with the mode (even when in peripheral- /
host-only mode) at least once.
So we can simply the sunxi musb glue by always registering its extcon
notifier and relying on sunxi_musb_work() to enable vbus when in
host-only mode.
This also enables host- and peripheral-only mode with vbus monitoring.
Ben Dooks [Thu, 30 Jun 2016 17:12:31 +0000 (12:12 -0500)]
usb: musb: sunxi: make unexported symbols static
The sunxi_musb_dma_controller_create and _destroy are not exported
or used outside the driver, so fix sparse warnings by making these
two static:
drivers/usb/musb/sunxi.c:357:23: warning: symbol 'sunxi_musb_dma_controller_create' was not declared. Should it be static?
drivers/usb/musb/sunxi.c:363:6: warning: symbol 'sunxi_musb_dma_controller_destroy' was not declared. Should it be static?
Bin Liu [Thu, 30 Jun 2016 17:12:24 +0000 (12:12 -0500)]
usb: musb: add tracepoints for register access
This adds tracepoints to musb register read/write wrappers to get
trace log for register access.
The default tacepoint log prefix here would be musb_readX/writeX(),
which is not much helpful. So this patch let the tracepoints use
__buildin_return_address(0) to print the caller funciton name to
provide more context of the register access.
projects / linux.git / log