There are clearly multiple calls, one per component, but they cannot be
discriminated from each other.
Change the ftrace events to also print the component name, to make it clear
which part of the code is involved. This requires changing the passed value
from a struct snd_soc_card, where the DAPM context is not kwown, to a
struct snd_soc_dapm_context where it is obviously known but the a card
pointer is also available.
intel-mid.h is providing some core parts of the South Complex PM,
which are usually are not used by individual drivers. In particular,
this driver doesn't use it, so simply remove the unused header.
Chancel Liu [Mon, 4 Mar 2024 07:21:28 +0000 (16:21 +0900)]
ASoC: soc-core.c: Prefer to return dai->driver->name in snd_soc_dai_name_get()
ASoC machine driver can use snd_soc_{of_}get_dlc() (A) to get DAI name
for dlc (snd_soc_dai_link_component). In this function call
dlc->dai_name is parsed via snd_soc_dai_name_get() (B).
(B) has a priority to return dai->name as dlc->dai_name. In most cases
card can probe successfully. However it has an issue that ASoC tries to
rebind card. Here is a simplified flow for example:
| a) Card probes successfully at first
| b) One of the component bound to this card is removed for some
| reason the component->dev is released
| c) That component is re-registered
v d) ASoC calls snd_soc_try_rebind_card()
a) points dlc->dai_name to dai->name. b) releases all resource of the
old DAI. c) creates new DAI structure. In result d) can not use
dlc->dai_name to add new created DAI.
So it's reasonable that prefer to return dai->driver->name in
snd_soc_dai_name_get() because dai->driver is a pre-defined global
variable. Also update snd_soc_is_matching_dai() for alignment.
ASoC: cs-amp-lib: Add KUnit test for calibration helpers
Add a KUnit test for the cs-amp-lib library. This has test cases
for cs_amp_get_efi_calibration_data() and cs_amp_write_cal_coeffs().
A KUNIT_STATIC_STUB_REDIRECT() has been added to
cs_amp_get_efi_variable() and cs_amp_write_cal_coeff() so that the
KUnit test can redirect these to test harness functions.
Much of the testing involves invoking the same function with different
parameters, i.e. the number of amps and the amp index within the array.
This uses parameterization rather than looping. The idea is to avoid
looping over configurations within one test case as that has a higher
chance of having a bug that doesn't actually test all the expected cases.
Having the test run exactly one configuration, and then tear-down, is less
prone to accidentally skipped configurations.
ASoC: cs35l56: Prevent bad sign extension in cs35l56_read_silicon_uid()
Cast u8 values to u32 when using them to build a 32-bit unsigned value
that is then stored in a u64. This avoids the possibility of a bad sign
extension where the u8 is implicitly extended to an int, thus changing it
from an unsigned to a signed value.
Whether this is a real problem is debatable, but it does no harm to
ensure that the u8 are cast to a suitable type for shifting.
This are various fixes and clean up gathered while working on Amlogic audio
support. These help better handle higher and unusual clock configuration
for TDM, SPDIF or PDM.
The patchset may not cover all codecs found in the codecs/ directory -
noticed a possible improvement and grepped for similar pattern across C
files found in the directory. Those addressed here seem pretty
straightforward.
Most of clk_xxx() functions do check if provided clk-pointer is
non-NULL. These do not check if the pointer is an error-pointer.
Providing such to a clk_xxx() results in a panic.
By utilizing _optional() variant of devm_clk_get() the driver code is
both simplified and more robust. There is no need to remember about
IS_ERR(clk) checks each time mclk is accessed.
Jerome Brunet [Fri, 23 Feb 2024 17:51:11 +0000 (18:51 +0100)]
ASoC: meson: axg-fifo: take continuous rates
The rate of the stream does not matter for the fifos of the axg family.
Fifos will just push or pull data to/from the DDR according to consumption
or production of the downstream element, which is the DPCM backend.
Drop the rate list and allow continuous rates. The lower and upper rate are
set according what is known to work with the different backends
This allows the PDM input backend to also use continuous rates.
Jerome Brunet [Fri, 23 Feb 2024 17:51:10 +0000 (18:51 +0100)]
ASoC: meson: axg-spdifin: use max width for rate detection
Use maximum width between 2 edges to setup spdifin thresholds
and detect the input sample rate. This comes from Amlogic SDK and
seems to be marginally more reliable than minimum width.
This is done to align with a future eARC support.
No issue was reported with minimum width so far, this is considered
to be an update so no Fixes tag is set.
According to Amlogic datasheets for the SoCs supported by this driver, the
maximum bit clock rate is 100MHz.
The tdm interface allows the rates listed by the DAI driver, regardless of
the number slots or their width. However, these will impact the bit clock
rate.
Hitting the 100MHz limit is very unlikely for most use cases but it is
possible.
For example with 32 slots / 32 bits wide, the maximum rate is no longer
384kHz but ~96kHz.
Add the constraint accordingly if the component is not already active.
If it is active, the rate is already constrained by the first stream rate.
Jerome Brunet [Fri, 23 Feb 2024 17:51:07 +0000 (18:51 +0100)]
ASoC: meson: axg-tdm-interface: fix mclk setup without mclk-fs
By default, when mclk-fs is not provided, the tdm-interface driver
requests an MCLK that is 4x the bit clock, SCLK.
However there is no justification for this:
* If the codec needs MCLK for its operation, mclk-fs is expected to be set
according to the codec requirements.
* If the codec does not need MCLK the minimum is 2 * SCLK, because this is
minimum the divider between SCLK and MCLK can do.
Multiplying by 4 may cause problems because the PLL limit may be reached
sooner than it should, so use 2x instead.
ASoC: codecs: tx-macro: correct TX SMIC MUXn widgets on SM8350+
Starting with Qualcomm SM8350 SoC, so Low Power Audio SubSystem (LPASS)
block version v9.2, the register responsible for TX SMIC MUXn muxes is
different. In earlier LPASS versions this mux had bit fields for
analogue (ADCn) and digital (SWR_DMICn) MICs. Choice of ADCn was
selecting the analogue path in CDC_TX_TOP_CSR_SWR_DMICn_CTL register.
With LPASS v9.2 and newer, the bit fields are integrated into just
SWR_MICn and there is no distinction for analogue or digital MIC in the
register.
Fix support for LPASS v9.2+:
1. Add new set of widgets and audio routes for LPASS v9.2.
2. Do not choose analogue or digital in CDC_TX_TOP_CSR_SWR_DMICn_CTL
based on value of the mux.
3. Replace all the input widgets (TX SWR_ADCn, TX SWR_DMICn) with TX
SWR_INPUTn ones.
The change is not backwards compatible with older DTBs and existing
mixer settings, therefore it does not change handling of older platforms
with working micrphones (SC8280xp) but only the ones with issues
(SM8450, SM8550) which need the fix.
ASoC: codecs: tx-macro: split widgets per different LPASS versions
TX macro codec differs slightly between different Qualcomm Low Power
Audio SubSystem (LPASS) block versions. In LPASS version 9.2 the
register responsible for TX SMIC MUXn muxes is different, thus to
properly support it, the driver needs to register different widgets per
different LPASS version.
Prepare for supporting this register difference by refactoring existing
code:
1. Move few widgets (TX SMIC MUXn, TX SWR_ADCn, TX SWR_DMICn) out of
common 'tx_macro_dapm_widgets[]' array to a new per-variant specific
array 'tx_macro_dapm_widgets_v9[]'.
2. Move also related audio routes into new array.
3. Store pointers to these variant-specific arrays in new variant-data
structure 'tx_macro_data'.
4. Add variant-specific widgets and routes in component probe, instead
of driver probe.
The change should have no real impact, except re-shuffling code and
registering some widgets and audio routes in component probe, instead of
driver probe.
ASoC: cs-amp-lib: Add helpers for factory calibration data
Create a new library for code that is used by multiple Cirrus Logic
amps. This initially implements extracting amp calibration data
from EFI and writing it to firmware controls.
During factory calibration of built-in speakers the firmware
calibration constants are stored in an EFI file. The file contains
an array of calibration constants for each of the speakers.
cs_amp_get_calibration_data() searches for an entry matching the
requested UID stamp, otherwise by array index. If the data is found in
EFI the constants for that speaker are copied back to the caller.
If EFI is not enabled, the cs_amp_get_calibration_data() implementation
will compile to simply return -ENOENT and the linker can drop the code.
The code to write calibration controls uses cs_dsp. Building of cs_dsp
is not forced. Instead, the code will compile away the calls to
cs_dsp if cs_dsp is not reachable.
This strategy of conditional code allows cs-amp-lib to be shared by
multiple drivers without forcing inclusion of other modules that might
be unnecessary.
The calls to efi.get_variable() and cs_dsp are in small wrapper
functions. This is so that a KUNIT_STATIC_STUB_REDIRECT can be added in
a future patch to redirect these calls to replacement functions for
KUnit testing.
Most of clk_xxx() functions do check if provided clk-pointer is
non-NULL. These do not check if the pointer is an error-pointer.
Providing such to a clk_xxx() results in a panic.
By utilizing _optional() variant of devm_clk_get() the driver code is
both simplified and more robust. There is no need to remember about
IS_ERR(clk) checks each time mclk is accessed.
Most of clk_xxx() functions do check if provided clk-pointer is
non-NULL. These do not check if the pointer is an error-pointer.
Providing such to a clk_xxx() results in a panic.
rt5640_set_dai_sysclk() is an example of that - clk_set_rate() is not
guarded by IS_ERR().
By utilizing _optional() variant of devm_clk_get() the driver code is
both simplified and more robust. There is no need to remember about
IS_ERR(clk) checks each time mclk is accessed.
Most of clk_xxx() functions do check if provided clk-pointer is
non-NULL. These do not check if the pointer is an error-pointer.
Providing such to a clk_xxx() results in a panic.
By utilizing _optional() variant of devm_clk_get() the driver code is
both simplified and more robust. There is no need to remember about
IS_ERR(clk) checks each time mclk is accessed.
Most of clk_xxx() functions do check if provided clk-pointer is
non-NULL. These do not check if the pointer is an error-pointer.
Providing such to a clk_xxx() results in a panic.
By utilizing _optional() variant of devm_clk_get() the driver code is
both simplified and more robust. There is no need to remember about
IS_ERR(clk) checks each time mclk is accessed.
Most of clk_xxx() functions do check if provided clk-pointer is
non-NULL. These do not check if the pointer is an error-pointer.
Providing such to a clk_xxx() results in a panic.
By utilizing _optional() variant of devm_clk_get() the driver code is
both simplified and more robust. There is no need to remember about
IS_ERR(clk) checks each time mclk is accessed.
Most of clk_xxx() functions do check if provided clk-pointer is
non-NULL. These do not check if the pointer is an error-pointer.
Providing such to a clk_xxx() results in a panic.
By utilizing _optional() variant of devm_clk_get() the driver code is
both simplified and more robust. There is no need to remember about
IS_ERR(clk) checks each time mclk is accessed.
On some boards with multiple WSA8840/WSA8845 speakers, the reset
(shutdown) GPIO is shared between two speakers. Use the reset
controller framework and its "reset-gpio" driver to handle this case.
This allows bring-up and proper handling of all WSA884x speakers on
X1E80100-CRD board.
ASoC: dt-bindings: qcom,wsa8840: Add reset-gpios for shared line
On newer Qualcomm platforms, like X1E80100-CRD, the WSA884x speakers
share SD_N GPIOs between two speakers, thus a coordinated assertion is
needed. Linux supports handling shared GPIO lines through "reset-gpios"
property, thus allow specifying either powerdown or reset GPIOs (these
are the same).
The avs-driver continues to be utilized on more recent Intel machines.
As TGL-based (cAVS 2.5) e.g.: RPL, inherit most of the functionality
from previous platforms:
SKL <- APL <- CNL <- ICL <- TGL
rather than putting everything into a single file, the platform-specific
bits are split into cnl/icl/tgl.c files instead. Makes the division clear
and code easier to maintain.
Layout of the patchset:
First are two changes combined together address the sound-clipping
problem, present when only one stream is running - specifically one
CAPTURE stream.
Follow up is naming-scheme adjustment for some of the existing functions
what improves code incohesiveness. As existing IPC/IRQ code operates
solely on cAVS 1.5 architecture, it needs no abstraction. The situation
changes when newer platforms come into the picture. Thus the next two
patches abstract the existing IPC/IRQ handlers so that majority of the
common code can be re-used.
The ICCMAX change stands out a bit - the AudioDSP firmware loading
procedure differs on ICL-based platforms (and onwards) and having a
separate commit makes the situation clear to the developers who are
going to support the solution from LTS perspective. For that reason
I decided not to merge it into the commit introducing the icl.c file.
Cezary Rojewski [Tue, 20 Feb 2024 11:50:35 +0000 (12:50 +0100)]
ASoC: Intel: avs: Populate board selection with new I2S entries
Update board selection with tables specifying supported I2S
configurations. DMIC/HDAudio board selection require no update as
dmic/hdaudio machine boards are generic and not tied to any specific
codec.
Cezary Rojewski [Tue, 20 Feb 2024 11:50:34 +0000 (12:50 +0100)]
ASoC: Intel: avs: ICCMAX recommendations for ICL+ platforms
For ICL+ platforms to avoid DMI/OPIO L1 entry during the base firmware
load procedure, HW recommends to set LTRP_GB to 95us and start an
additional CAPTURE stream in the background.
Once the load completes, original LTRP_GB value is restored and the
additional stream is released.
Cezary Rojewski [Tue, 20 Feb 2024 11:50:33 +0000 (12:50 +0100)]
ASoC: Intel: avs: TGL-based platforms support
Define handlers specific to cAVS 2.5 platforms, that is TGL, ADL, RPL
and all other variants based on this very version of AudioDSP
architecture. Most operations are inherited from their predecessors with
the major difference being AudioDSP cores management - firmware handlers
that on its own so there is no need to interfere.
Cezary Rojewski [Tue, 20 Feb 2024 11:50:32 +0000 (12:50 +0100)]
ASoC: Intel: avs: ICL-based platforms support
Define handlers specific to cAVS 2.0 platforms, that is ICL, JSL and all
other variants based on this very version of AudioDSP architecture. Most
operations are inherited from their predecessors with the major
difference being firmware-logging functionality - IPC request as well as
debug memory windows layout have changed.
Cezary Rojewski [Tue, 20 Feb 2024 11:50:31 +0000 (12:50 +0100)]
ASoC: Intel: avs: CNL-based platforms support
Define handlers specific to cAVS 1.8 platforms, that is CNL, CFL, CML
and all other variants based on this very version of AudioDSP
architecture. Most operations are inherited from their predecessors.
Cezary Rojewski [Tue, 20 Feb 2024 11:50:30 +0000 (12:50 +0100)]
ASoC: Intel: avs: Abstract IRQ handling
Servicing IPCs on CNL platforms and onward differs from the existing
one. To make room for these, relocate SKL-based platforms specific code
into the skl.c file leaving only the genering irq_handler in the common
code.
Cezary Rojewski [Tue, 20 Feb 2024 11:50:29 +0000 (12:50 +0100)]
ASoC: Intel: avs: Abstract IPC handling
Servicing IPCs on CNL platforms and onward differs from the existing
one. To make room for these, enrich platform descriptor with fields
representing crucial IPC registers and utilize them throughout the code.
While cleaning up device descriptors, reduce the number of code lines by
assigning 'min_fw_version' within a single line.
Cezary Rojewski [Tue, 20 Feb 2024 11:50:27 +0000 (12:50 +0100)]
ASoC: Intel: avs: Fix sound clipping in single capture scenario
To avoid sound clipping when there just one, single CAPTURE stream
ongoing, disable L1SEN before it is started. Any PLAYBACK stream or
additional CAPTURE allows L1SEN to be re-enabled.
Cezary Rojewski [Tue, 20 Feb 2024 11:50:26 +0000 (12:50 +0100)]
ASoC: Intel: avs: L1SEN reference counted
Code loading is not the only procedure that manipulates L1SEN. Update
existing mechanism so the stream starting procedure can interfere with
L1SEN without causing any trouble to its other users.
Colin Ian King [Fri, 16 Feb 2024 14:22:19 +0000 (14:22 +0000)]
ASoC: tas2781: Remove redundant initialization of pointer 'data'
The pointer 'data' being initialized with a value that is never read, it
is being re-assigned inside a while-loop. The initialization is redundant
and can be removed.
Cleans up clang scan build warning
sound/soc/codecs/tas2781-fmwlib.c:1534:17: warning: Value stored to
'data' during its initialization is never read [deadcode.DeadStores]
Arnd Bergmann [Mon, 19 Feb 2024 09:38:45 +0000 (10:38 +0100)]
ASoC: SOF: amd: fix soundwire dependencies
The soundwire-amd driver has a bit of a layering violation requiring
the SOF driver to directly call into its exported symbols rather than
through an abstraction.
The SND_SOC_SOF_AMD_SOUNDWIRE Kconfig symbol tries to deal with the
dependency by selecting SOUNDWIRE_AMD in a complicated set of conditions,
but gets it wrong for a configuration involving SND_SOC_SOF_AMD_COMMON=y,
SND_SOC_SOF_AMD_ACP63=m, and SND_SOC_SOF_AMD_SOUNDWIRE_LINK_BASELINE=m
SOUNDWIRE_AMD=m, which results in a link failure:
In essence, the SND_SOC_SOF_AMD_COMMON option cannot be built-in when
trying to link against a modular SOUNDWIRE_AMD driver.
Since CONFIG_SOUNDWIRE_AMD is a user-visible option, it really should
never be selected by another driver in the first place, so replace the
extra complexity with a normal Kconfig dependency in SND_SOC_SOF_AMD_SOUNDWIRE,
plus a top-level check that forbids any of the AMD SOF drivers from being
built-in with CONFIG_SOUNDWIRE_AMD=m.
In normal configs, they should all either be built-in or all loadable
modules anyway, so this simplification does not limit any real usecases.
Vijendar Mukunda [Wed, 14 Feb 2024 10:40:04 +0000 (16:10 +0530)]
ASoC: amd: ps: fix for acp pme wake for soundwire configuration
Consider the below scenario, When ACP and SoundWire managers are in
D3 state and SoundWire manager power off mode is selected and acp and
SoundWire manager instances are in runtime suspended state.
In this case, for the ACP PME wake event, the ACP PCI driver should resume
SoundWire manager devices based on wake enable status set.
Add code for handling ACP PME wake event for runtime suspend scenario
when SoundWire power off mode is selected.
Vijendar Mukunda [Wed, 14 Feb 2024 10:40:03 +0000 (16:10 +0530)]
ASoC: amd: ps: remove acp_reset flag
The earlier acp_reset flag is set to true in two instances as mentioned
below.
1. When active SoundWire manager instances power mode is set to
Power off mode when SoundWire configuration is selected.
2. For other acp configurations
As code being refactored and common function being used for scanning
SoundWire controller, acp_reset flag update logic is dropped.
Instead of it, check the SoundWire manager instance enable state, based on
it update sdw_en_stat flag which will be used to apply ACP init/de-init
sequence during suspend/resume callbacks based on flag set value when
SoundWire configuration is selected.
For other acp configurations, acp init/de-init will be called by default.
Refactor existing pm ops logic for SoundWire configuration and use
sdw_en_stat flag for invoking acp init/de-init sequence.
Linus Torvalds [Sun, 18 Feb 2024 18:09:25 +0000 (10:09 -0800)]
Merge tag 'kbuild-fixes-v6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Reformat nested if-conditionals in Makefiles with 4 spaces
- Fix CONFIG_DEBUG_INFO_BTF builds for big endian
- Fix modpost for module srcversion
- Fix an escape sequence warning in gen_compile_commands.py
- Fix kallsyms to ignore ARMv4 thunk symbols
* tag 'kbuild-fixes-v6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kallsyms: ignore ARMv4 thunks along with others
modpost: trim leading spaces when processing source files list
gen_compile_commands: fix invalid escape sequence warning
kbuild: Fix changing ELF file type for output of gen_btf for big endian
docs: kconfig: Fix grammar and formatting
kbuild: use 4-space indentation when followed by conditionals
Linus Torvalds [Sun, 18 Feb 2024 17:22:48 +0000 (09:22 -0800)]
Merge tag 'x86_urgent_for_v6.8_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Borislav Petkov:
- Use a GB page for identity mapping only when memory of this size is
requested so that mapping of reserved regions is prevented which
would otherwise lead to system crashes on UV machines
* tag 'x86_urgent_for_v6.8_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/ident_map: Use gbpages only where full GB page should be mapped.
- Prevent spurious interrupts on Broadcom devices using GIC v3
architecture
- Other minor fixes
* tag 'irq_urgent_for_v6.8_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix GICv4.1 VPE affinity update
irqchip/gic-v3-its: Restore quirk probing for ACPI-based systems
irqchip/gic-v3-its: Handle non-coherent GICv4 redistributors
irqchip/qcom-mpm: Fix IS_ERR() vs NULL check in qcom_mpm_init()
irqchip/loongson-eiointc: Use correct struct type in eiointc_domain_alloc()
irqchip/irq-brcmstb-l2: Add write memory barrier before exit
Linus Torvalds [Sun, 18 Feb 2024 17:08:57 +0000 (09:08 -0800)]
Merge tag 'i2c-for-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two fixes for i801 and qcom-geni devices. Meanwhile, a fix from Arnd
addresses a compilation error encountered during compile test on
powerpc"
* tag 'i2c-for-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Fix block process call transactions
i2c: pasemi: split driver into two separate modules
i2c: qcom-geni: Correct I2C TRE sequence
Linus Torvalds [Sun, 18 Feb 2024 00:59:31 +0000 (16:59 -0800)]
Merge tag 'powerpc-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"This is a bit of a big batch for rc4, but just due to holiday hangover
and because I didn't send any fixes last week due to a late revert
request. I think next week should be back to normal.
- Fix ftrace bug on boot caused by exit text sections with
'-fpatchable-function-entry'
- Fix accuracy of stolen time on pseries since the switch to
VIRT_CPU_ACCOUNTING_GEN
- Fix a crash in the IOMMU code when doing DLPAR remove
- Set pt_regs->link on scv entry to fix BPF stack unwinding
- Add missing PPC_FEATURE_BOOKE on 64-bit e5500/e6500, which broke
gdb
- Fix boot on some 6xx platforms with STRICT_KERNEL_RWX enabled
- Fix build failures with KASAN enabled and 32KB stack size
- Some other minor fixes
Thanks to Arnd Bergmann, Benjamin Gray, Christophe Leroy, David
Engraf, Gaurav Batra, Jason Gunthorpe, Jiangfeng Xiao, Matthias
Schiffer, Nathan Lynch, Naveen N Rao, Nicholas Piggin, Nysal Jan K.A,
R Nageswara Sastry, Shivaprasad G Bhat, Shrikanth Hegde, Spoorthy,
Srikar Dronamraju, and Venkat Rao Bagalkote"
* tag 'powerpc-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/iommu: Fix the missing iommu_group_put() during platform domain attach
powerpc/pseries: fix accuracy of stolen time
powerpc/ftrace: Ignore ftrace locations in exit text sections
powerpc/cputable: Add missing PPC_FEATURE_BOOKE on PPC64 Book-E
powerpc/kasan: Limit KASAN thread size increase to 32KB
Revert "powerpc/pseries/iommu: Fix iommu initialisation during DLPAR add"
powerpc: 85xx: mark local functions static
powerpc: udbg_memcons: mark functions static
powerpc/kasan: Fix addr error caused by page alignment
powerpc/6xx: set High BAT Enable flag on G2_LE cores
selftests/powerpc/papr_vpd: Check devfd before get_system_loc_code()
powerpc/64: Set task pt_regs->link to the LR value on scv entry
powerpc/pseries/iommu: Fix iommu initialisation during DLPAR add
powerpc/pseries/papr-sysparm: use u8 arrays for payloads
Linus Torvalds [Sat, 17 Feb 2024 16:56:41 +0000 (08:56 -0800)]
Merge tag 'driver-core-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes, a kobject fix, and a documentation
update for 6.8-rc5. In detail these changes are:
- devlink fixes for reported issues with 6.8-rc1
- topology scheduling regression fix that has been reported by many
- kobject loosening of checks change in -rc1 is now reverted as some
codepaths seemed to need the checks
- documentation update for the CVE process. Has been reviewed by
many, the last minute change to the document was to bring the .rst
format back into the the new style rules, the contents did not
change.
All of these, except for the documentation update, have been in
linux-next for over a week. The documentation update has been reviewed
for weeks by a group of developers, and in public for a week and the
wording has stabilized for now. If future changes are needed, we can
do so before 6.8-final is out (or anytime after that)"
* tag 'driver-core-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation: Document the Linux Kernel CVE process
Revert "kobject: Remove redundant checks for whether ktype is NULL"
driver core: fw_devlink: Improve logs for cycle detection
driver core: fw_devlink: Improve detection of overlapping cycles
driver core: Fix device_link_flag_is_sync_state_only()
topology: Set capacity_freq_ref in all cases
Linus Torvalds [Sat, 17 Feb 2024 16:52:38 +0000 (08:52 -0800)]
Merge tag 'char-misc-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / miscdriver fixes from Greg KH:
"Here is a small set of char/misc and IIO driver fixes for 6.8-rc5.
Included in here are:
- lots of iio driver fixes for reported issues
- nvmem device naming fixup for reported problem
- interconnect driver fixes for reported issues
All of these have been in linux-next for a while with no reported the
issues (the nvmem patch was included in a different branch in
linux-next before sent to me for inclusion here)"
* tag 'char-misc-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
nvmem: include bit index in cell sysfs file name
iio: adc: ad4130: only set GPIO_CTRL if pin is unused
iio: adc: ad4130: zero-initialize clock init data
interconnect: qcom: x1e80100: Add missing ACV enable_mask
interconnect: qcom: sm8650: Use correct ACV enable_mask
iio: accel: bma400: Fix a compilation problem
iio: commom: st_sensors: ensure proper DMA alignment
iio: hid-sensor-als: Return 0 for HID_USAGE_SENSOR_TIME_TIMESTAMP
iio: move LIGHT_UVA and LIGHT_UVB to the end of iio_modifier
staging: iio: ad5933: fix type mismatch regression
iio: humidity: hdc3020: fix temperature offset
iio: adc: ad7091r8: Fix error code in ad7091r8_gpio_setup()
iio: adc: ad_sigma_delta: ensure proper DMA alignment
iio: imu: adis: ensure proper DMA alignment
iio: humidity: hdc3020: Add Makefile, Kconfig and MAINTAINERS entry
iio: imu: bno055: serdev requires REGMAP
iio: magnetometer: rm3100: add boundary check for the value read from RM3100_REG_TMRC
iio: pressure: bmp280: Add missing bmp085 to SPI id table
iio: core: fix memleak in iio_device_register_sysfs
interconnect: qcom: sm8550: Enable sync_state
...
Linus Torvalds [Sat, 17 Feb 2024 16:46:57 +0000 (08:46 -0800)]
Merge tag 'tty-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial fixes from Greg KH:
"Here are three small tty and serial driver fixes for 6.8-rc5:
- revert a 8250_pci1xxxx off-by-one change that was incorrect
- two changes to fix the transmit path of the mxs-auart driver,
fixing a regression in the 6.2 release
All of these have been in linux-next for over a week with no reported
issues"
* tag 'tty-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: mxs-auart: fix tx
serial: core: introduce uart_port_tx_flags()
serial: 8250_pci1xxxx: partially revert off by one patch
Linus Torvalds [Sat, 17 Feb 2024 16:44:55 +0000 (08:44 -0800)]
Merge tag 'usb-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt fixes from Greg KH:
"Here are two small fixes for 6.8-rc5:
- thunderbolt to fix a reported issue on many platforms
- dwc3 driver revert of a commit that caused problems in -rc1
Both of these changes have been in linux-next for over a week with no
reported issues"
* tag 'usb-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "usb: dwc3: Support EBC feature of DWC_usb31"
thunderbolt: Fix setting the CNS bit in ROUTER_CS_5
Linus Torvalds [Sat, 17 Feb 2024 16:13:32 +0000 (08:13 -0800)]
Merge tag 'media/v6.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- regression fix for rkisp1 shared IRQ logic
- fix atomisp breakage due to a kAPI change
- permission fix for remote controller BPF support
- memleak fix in ir_toy driver
- Kconfig dependency fix for pwm-ir-rx
* tag 'media/v6.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: pwm-ir-tx: Depend on CONFIG_HIGH_RES_TIMERS
media: ir_toy: fix a memleak in irtoy_tx
media: rc: bpf attach/detach requires write permission
media: atomisp: Adjust for v4l2_subdev_state handling changes in 6.8
media: rkisp1: Fix IRQ handling due to shared interrupts
media: Revert "media: rkisp1: Drop IRQF_SHARED"
Linus Torvalds [Sat, 17 Feb 2024 16:06:20 +0000 (08:06 -0800)]
Merge tag 'pci-v6.8-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Keep bridges in D0 if we need to poll downstream devices for PME to
resolve a v6.6 regression where we failed to enumerate devices below
bridges put in D3hot by runtime PM, e.g., NVMe drives connected via
Thunderbolt or USB4 docks (Alex Williamson)
- Add Siddharth Vadapalli as PCI TI DRA7XX/J721E reviewer
* tag 'pci-v6.8-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
MAINTAINERS: Add Siddharth Vadapalli as PCI TI DRA7XX/J721E reviewer
PCI: Fix active state requirement in PME polling
Linus Torvalds [Sat, 17 Feb 2024 15:59:47 +0000 (07:59 -0800)]
Merge tag 'probes-fixes-v6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fix from Masami Hiramatsu:
- tracing/probes: Fix BTF structure member finder to find the members
which are placed after any anonymous union member correctly.
* tag 'probes-fixes-v6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/probes: Fix to search structure fields correctly
Linus Torvalds [Sat, 17 Feb 2024 15:56:10 +0000 (07:56 -0800)]
Merge tag '6.8-rc4-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
"Five smb3 client fixes, most also for stable:
- Two multichannel fixes (one to fix potential handle leak on retry)
- Work around possible serious data corruption (due to change in
folios in 6.3, for cases when non standard maximum write size
negotiated)
- Symlink creation fix
- Multiuser automount fix"
* tag '6.8-rc4-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: Fix regression in writes when non-standard maximum write size negotiated
smb: client: handle path separator of created SMB symlinks
smb: client: set correct id, uid and cruid for multiuser automounts
cifs: update the same create_guid on replay
cifs: fix underflow in parse_server_interfaces()
Documentation: Document the Linux Kernel CVE process
The Linux kernel project now has the ability to assign CVEs to fixed
issues, so document the process and how individual developers can get a
CVE if one is not automatically assigned for their fixes.
tracing/probes: Fix to search structure fields correctly
Fix to search a field from the structure which has anonymous union
correctly.
Since the reference `type` pointer was updated in the loop, the search
loop suddenly aborted where it hits an anonymous union. Thus it can not
find the field after the anonymous union. This avoids updating the
cursor `type` pointer in the loop.
Wolfram Sang [Sat, 17 Feb 2024 12:13:33 +0000 (13:13 +0100)]
Merge tag 'i2c-host-fixes-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
Three fixes are included here. Two are strictly hardware-related
for the i801 and qcom-geni devices. Meanwhile, a fix from Arnd
addresses a compilation error encountered during compile test on
powerpc.
Linus Torvalds [Fri, 16 Feb 2024 22:05:02 +0000 (14:05 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three fixes: the two fnic ones are a revert and a refix, which is why
the diffstat is a bit big. The target one also extracts a function to
add a check for configuration and so looks bigger than it is"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fnic: Move fnic_fnic_flush_tx() to a work queue
scsi: Revert "scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock"
scsi: target: Fix unmap setup during configuration
Linus Torvalds [Fri, 16 Feb 2024 22:00:19 +0000 (14:00 -0800)]
Merge tag 'wq-for-6.8-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"Just one patch to revert commit ca10d851b9ad ("workqueue: Override
implicit ordered attribute in workqueue_apply_unbound_cpumask()").
This commit could break ordering guarantees for ordered workqueues.
The problem that the commit tried to resolve partially - making
ordered workqueues follow unbound cpumask - is fully solved in
wq/for-6.9 branch"
* tag 'wq-for-6.8-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
Revert "workqueue: Override implicit ordered attribute in workqueue_apply_unbound_cpumask()"
Linus Torvalds [Fri, 16 Feb 2024 21:37:15 +0000 (13:37 -0800)]
Merge tag 'ceph-for-6.8-rc5' of https://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Additional cap handling fixes from Xiubo to avoid "client isn't
responding to mclientcaps(revoke)" stalls on the MDS side"
* tag 'ceph-for-6.8-rc5' of https://github.com/ceph/ceph-client:
ceph: add ceph_cap_unlink_work to fire check_caps() immediately
ceph: always queue a writeback when revoking the Fb caps
Linus Torvalds [Fri, 16 Feb 2024 18:48:14 +0000 (10:48 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM:
- Avoid dropping the page refcount twice when freeing an unlinked
page-table subtree.
- Don't source the VFIO Kconfig twice
- Fix protected-mode locking order between kvm and vcpus
RISC-V:
- Fix steal-time related sparse warnings
x86:
- Cleanup gtod_is_based_on_tsc() to return "bool" instead of an "int"
- Make a KVM_REQ_NMI request while handling KVM_SET_VCPU_EVENTS if
and only if the incoming events->nmi.pending is non-zero. If the
target vCPU is in the UNITIALIZED state, the spurious request will
result in KVM exiting to userspace, which in turn causes QEMU to
constantly acquire and release QEMU's global mutex, to the point
where the BSP is unable to make forward progress.
- Fix a type (u8 versus u64) goof that results in pmu->fixed_ctr_ctrl
being incorrectly truncated, and ultimately causes KVM to think a
fixed counter has already been disabled (KVM thinks the old value
is '0').
- Fix a stack leak in KVM_GET_MSRS where a failed MSR read from
userspace that is ultimately ignored due to ignore_msrs=true
doesn't zero the output as intended.
Selftests cleanups and fixes:
- Remove redundant newlines from error messages.
- Delete an unused variable in the AMX test (which causes build
failures when compiling with -Werror).
- Fail instead of skipping tests if open(), e.g. of /dev/kvm, fails
with an error code other than ENOENT (a Hyper-V selftest bug
resulted in an EMFILE, and the test eventually got skipped).
- Fix TSC related bugs in several Hyper-V selftests.
- Fix a bug in the dirty ring logging test where a sem_post() could
be left pending across multiple runs, resulting in incorrect
synchronization between the main thread and the vCPU worker thread.
- Relax the dirty log split test's assertions on 4KiB mappings to fix
false positives due to the number of mappings for memslot 0 (used
for code and data that is NOT being dirty logged) changing, e.g.
due to NUMA balancing"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
KVM: arm64: Fix double-free following kvm_pgtable_stage2_free_unlinked()
RISC-V: KVM: Use correct restricted types
RISC-V: paravirt: Use correct restricted types
RISC-V: paravirt: steal_time should be static
KVM: selftests: Don't assert on exact number of 4KiB in dirty log split test
KVM: selftests: Fix a semaphore imbalance in the dirty ring logging test
KVM: x86: Fix KVM_GET_MSRS stack info leak
KVM: arm64: Do not source virt/lib/Kconfig twice
KVM: x86/pmu: Fix type length error when reading pmu->fixed_ctr_ctrl
KVM: x86: Make gtod_is_based_on_tsc() return 'bool'
KVM: selftests: Make hyperv_clock require TSC based system clocksource
KVM: selftests: Run clocksource dependent tests with hyperv_clocksource_tsc_page too
KVM: selftests: Use generic sys_clocksource_is_tsc() in vmx_nested_tsc_scaling_test
KVM: selftests: Generalize check_clocksource() from kvm_clock_test
KVM: x86: make KVM_REQ_NMI request iff NMI pending for vcpu
KVM: arm64: Fix circular locking dependency
KVM: selftests: Fail tests when open() fails with !ENOENT
KVM: selftests: Avoid infinite loop in hyperv_features when invtsc is missing
KVM: selftests: Delete superfluous, unused "stage" variable in AMX test
KVM: selftests: x86_64: Remove redundant newlines
...
Linus Torvalds [Fri, 16 Feb 2024 18:33:51 +0000 (10:33 -0800)]
Merge tag 'trace-v6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix the #ifndef that didn't have the 'CONFIG_' prefix on
HAVE_DYNAMIC_FTRACE_WITH_REGS
The fix to have dynamic trampolines work with x86 broke arm64 as the
config used in the #ifdef was HAVE_DYNAMIC_FTRACE_WITH_REGS and not
CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS which removed the fix that the
previous fix was to fix.
- Fix tracing_on state
The code to test if "tracing_on" is set incorrectly used
ring_buffer_record_is_on() which returns false if the ring buffer
isn't able to be written to.
But the ring buffer disable has several bits that disable it. One is
internal disabling which is used for resizing and other modifications
of the ring buffer. But the "tracing_on" user space visible flag
should only report if tracing is actually on and not internally
disabled, as this can cause confusion as writing "1" when it is
disabled will not enable it.
Instead use ring_buffer_record_is_set_on() which shows the user space
visible settings.
- Fix a false positive kmemleak on saved cmdlines
Now that the saved_cmdlines structure is allocated via alloc_page()
and not via kmalloc() it has become invisible to kmemleak. The
allocation done to one of its pointers was flagged as a dangling
allocation leak. Make kmemleak aware of this allocation and free.
- Fix synthetic event dynamic strings
An update that cleaned up the synthetic event code removed the return
value of trace_string(), and had it return zero instead of the
length, causing dynamic strings in the synthetic event to always have
zero size.
- Clean up documentation and header files for seq_buf
* tag 'trace-v6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
seq_buf: Fix kernel documentation
seq_buf: Don't use "proxy" headers
tracing/synthetic: Fix trace_string() return value
tracing: Inform kmemleak of saved_cmdlines allocation
tracing: Use ring_buffer_record_is_set_on() in tracer_tracing_is_on()
tracing: Fix HAVE_DYNAMIC_FTRACE_WITH_REGS ifdef
Linus Torvalds [Fri, 16 Feb 2024 18:28:29 +0000 (10:28 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"It's a little busier than normal, but it's still not a lot of code and
things seem fairly quiet in general:
- Fix allocation failure during SVE coredumps
- Fix handling of SVE context on signal delivery
- Enable Neoverse N2 CPU errata workarounds for Microsoft's "Azure
Cobalt 100" clone
- Work around CMN PMU erratum in AmpereOneX implementation
- Fix typo in CXL PMU event definition
- Fix jump label asm constraints"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/sve: Lower the maximum allocation for the SVE ptrace regset
arm64: Subscribe Microsoft Azure Cobalt 100 to ARM Neoverse N2 errata
perf/arm-cmn: Workaround AmpereOneX errata AC04_MESH_1 (incorrect child count)
arm64: jump_label: use constraints "Si" instead of "i"
arm64: fix typo in comments
perf: CXL: fix mismatched cpmu event opcode
arm64/signal: Don't assume that TIF_SVE means we saved SVE state
Linus Torvalds [Fri, 16 Feb 2024 17:29:26 +0000 (09:29 -0800)]
Merge tag 'zonefs-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs fix from Damien Le Moal:
- Fix direct write error handling to avoid a race between failed IO
completion and the submission path itself which can result in an
invalid file size exposed to the user after the failed IO.
* tag 'zonefs-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Improve error handling
Linus Torvalds [Fri, 16 Feb 2024 17:02:19 +0000 (09:02 -0800)]
Merge tag 'sound-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of device-specific fixes. It became a bit bigger than
wished, but all look reasonably small and safe to apply.
- A few Cirrus Logic CS35L56 and CS42L43 driver fixes
- ASoC SOF fixes and workarounds
- Various ASoC Intel fixes
- Lots of HD-, USB-audio and AMD ACP quirks"
* tag 'sound-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (33 commits)
ALSA: usb-audio: More relaxed check of MIDI jack names
ALSA: hda/realtek: fix mute/micmute LED For HP mt645
ALSA: hda/realtek: cs35l41: Fix order and duplicates in quirks table
ALSA: hda/realtek: cs35l41: Fix device ID / model name
ALSA: hda/realtek: cs35l41: Add internal speaker support for ASUS UM3402 with missing DSD
ASoC: cs35l56: Workaround for ACPI with broken spk-id-gpios property
ALSA: hda: Add Lenovo Legion 7i gen7 sound quirk
ASoC: SOF: IPC3: fix message bounds on ipc ops
ASoC: SOF: ipc4-pcm: Workaround for crashed firmware on system suspend
ASoC: q6dsp: fix event handler prototype
ASoC: SOF: Intel: pci-lnl: Change the topology path to intel/sof-ipc4-tplg
ASoC: SOF: Intel: pci-tgl: Change the default paths and firmware names
ASoC: amd: yc: Fix non-functional mic on Lenovo 82UU
ASoC: rt5645: Add DMI quirk for inverted jack-detect on MeeGoPad T8
ASoC: rt5645: Make LattePanda board DMI match more precise
ASoC: SOF: amd: Fix locking in ACP IRQ handler
ASoC: rt5645: Fix deadlock in rt5645_jack_detect_work()
ASoC: Intel: cht_bsw_rt5645: Cleanup codec_name handling
ASoC: Intel: Boards: Fix NULL pointer deref in BYT/CHT boards
ASoC: cs35l56: Remove default from IRQ1_CFG register
...
Linus Torvalds [Fri, 16 Feb 2024 16:55:46 +0000 (08:55 -0800)]
Merge tag 'gpio-fixes-for-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- add missing stubs for functions that are not built with GPIOLIB
disabled
* tag 'gpio-fixes-for-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: add gpio_device_get_label() stub for !GPIOLIB
gpiolib: add gpio_device_get_base() stub for !GPIOLIB
gpiolib: add gpiod_to_gpio_device() stub for !GPIOLIB
Linus Torvalds [Fri, 16 Feb 2024 16:05:30 +0000 (08:05 -0800)]
Merge tag 'drm-fixes-2024-02-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular weekly fixes, nothing too major, mostly amdgpu, then i915, xe,
msm and nouveau with some scattered bits elsewhere.
crtc:
- fix uninit variable
prime:
- support > 4GB page arrays
buddy:
- fix error handling in allocations
i915:
- fix blankscreen on JSL chromebooks
- stable fix to limit DP sst link rates
xe:
- Fix an out-of-bounds shift.
- Fix the display code thinking xe uses shmem
- Fix a warning about index out-of-bound
- Fix a clang-16 compilation warning
amdgpu:
- PSR fixes
- Suspend/resume fixes
- Link training fix
- Aspect ratio fix
- DCN 3.5 fixes
- VCN 4.x fix
- GFX 11 fix
- Misc display fixes
- Misc small fixes
amdkfd:
- Cache size reporting fix
- SIMD distribution fix
msm:
- GPU:
- dmabuf vmap fix
- a610 UBWC corruption fix (incorrect hbb)
- revert a commit that was making GPU recovery unreliable
- tlb invalidation fix
* tag 'drm-fixes-2024-02-16' of git://anongit.freedesktop.org/drm/drm: (38 commits)
drm/amdgpu: Fix implicit assumtion in gfx11 debug flags
drm/amdkfd: update SIMD distribution algo for GFXIP 9.4.2 onwards
drm/amd/display: Increase ips2_eval delay for DCN35
drm/amdgpu/display: Initialize gamma correction mode variable in dcn30_get_gamcor_current()
drm/amdgpu/soc21: update VCN 4 max HEVC encoding resolution
drm/amd/display: fixed integer types and null check locations
drm/amd/display: Fix array-index-out-of-bounds in dcn35_clkmgr
drm/amd/display: Preserve original aspect ratio in create stream
drm/amd/display: Fix possible NULL dereference on device remove/driver unload
Revert "drm/amd/display: increased min_dcfclk_mhz and min_fclk_mhz"
drm/amd/display: Add align done check
Revert "drm/amd: flush any delayed gfxoff on suspend entry"
drm/amd: Stop evicting resources on APUs in suspend
drm/amd/display: Fix possible buffer overflow in 'find_dcfclk_for_voltage()'
drm/amd/display: Fix possible use of uninitialized 'max_chunks_fbc_mode' in 'calculate_bandwidth()'
drm/amd/display: Initialize 'wait_time_microsec' variable in link_dp_training_dpia.c
drm/amd/display: Fix && vs || typos
drm/amdkfd: Fix L2 cache size reporting in GFX9.4.3
drm/amdgpu: make damage clips support configurable
drm/msm: Wire up tlb ops
...
Dave Airlie [Fri, 16 Feb 2024 05:45:03 +0000 (15:45 +1000)]
Merge tag 'drm-xe-fixes-2024-02-15' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- Fix an out-of-bounds shift.
- Fix the display code thinking xe uses shmem
- Fix a warning about index out-of-bound
- Fix a clang-16 compilation warning
Dave Airlie [Fri, 16 Feb 2024 04:33:09 +0000 (14:33 +1000)]
Merge tag 'drm-misc-fixes-2024-02-15' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
A suspend/resume error fix for ivpu, a couple of scheduler fixes for
nouveau, a patch to support large page arrays in prime, a uninitialized
variable fix in crtc, a locking fix in rockchip/vop2 and a buddy
allocator error reporting fix.
Steve French [Tue, 6 Feb 2024 22:34:22 +0000 (16:34 -0600)]
smb: Fix regression in writes when non-standard maximum write size negotiated
The conversion to netfs in the 6.3 kernel caused a regression when
maximum write size is set by the server to an unexpected value which is
not a multiple of 4096 (similarly if the user overrides the maximum
write size by setting mount parm "wsize", but sets it to a value that
is not a multiple of 4096). When negotiated write size is not a
multiple of 4096 the netfs code can skip the end of the final
page when doing large sequential writes, causing data corruption.
This section of code is being rewritten/removed due to a large
netfs change, but until that point (ie for the 6.3 kernel until now)
we can not support non-standard maximum write sizes.
Add a warning if a user specifies a wsize on mount that is not
a multiple of 4096 (and round down), also add a change where we
round down the maximum write size if the server negotiates a value
that is not a multiple of 4096 (we also have to check to make sure that
we do not round it down to zero).
Damien Le Moal [Thu, 8 Feb 2024 08:26:59 +0000 (17:26 +0900)]
zonefs: Improve error handling
Write error handling is racy and can sometime lead to the error recovery
path wrongly changing the inode size of a sequential zone file to an
incorrect value which results in garbage data being readable at the end
of a file. There are 2 problems:
1) zonefs_file_dio_write() updates a zone file write pointer offset
after issuing a direct IO with iomap_dio_rw(). This update is done
only if the IO succeed for synchronous direct writes. However, for
asynchronous direct writes, the update is done without waiting for
the IO completion so that the next asynchronous IO can be
immediately issued. However, if an asynchronous IO completes with a
failure right before the i_truncate_mutex lock protecting the update,
the update may change the value of the inode write pointer offset
that was corrected by the error path (zonefs_io_error() function).
2) zonefs_io_error() is called when a read or write error occurs. This
function executes a report zone operation using the callback function
zonefs_io_error_cb(), which does all the error recovery handling
based on the current zone condition, write pointer position and
according to the mount options being used. However, depending on the
zoned device being used, a report zone callback may be executed in a
context that is different from the context of __zonefs_io_error(). As
a result, zonefs_io_error_cb() may be executed without the inode
truncate mutex lock held, which can lead to invalid error processing.
Fix both problems as follows:
- Problem 1: Perform the inode write pointer offset update before a
direct write is issued with iomap_dio_rw(). This is safe to do as
partial direct writes are not supported (IOMAP_DIO_PARTIAL is not
set) and any failed IO will trigger the execution of zonefs_io_error()
which will correct the inode write pointer offset to reflect the
current state of the one on the device.
- Problem 2: Change zonefs_io_error_cb() into zonefs_handle_io_error()
and call this function directly from __zonefs_io_error() after
obtaining the zone information using blkdev_report_zones() with a
simple callback function that copies to a local stack variable the
struct blk_zone obtained from the device. This ensures that error
handling is performed holding the inode truncate mutex.
This change also simplifies error handling for conventional zone files
by bypassing the execution of report zones entirely. This is safe to
do because the condition of conventional zones cannot be read-only or
offline and conventional zone files are always fully mapped with a
constant file size.
Linus Torvalds [Thu, 15 Feb 2024 19:39:27 +0000 (11:39 -0800)]
Merge tag 'net-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from can, wireless and netfilter.
Current release - regressions:
- af_unix: fix task hung while purging oob_skb in GC
- pds_core: do not try to run health-thread in VF path
Current release - new code bugs:
- sched: act_mirred: don't zero blockid when net device is being
deleted
Previous releases - regressions:
- netfilter:
- nat: restore default DNAT behavior
- nf_tables: fix bidirectional offload, broken when unidirectional
offload support was added
- openvswitch: limit the number of recursions from action sets
- eth: i40e: do not allow untrusted VF to remove administratively set
MAC address
Previous releases - always broken:
- tls: fix races and bugs in use of async crypto
- mptcp: prevent data races on some of the main socket fields, fix
races in fastopen handling
- dpll: fix possible deadlock during netlink dump operation
- dsa: lan966x: fix crash when adding interface under a lag when some
of the ports are disabled
- can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock
Misc:
- a handful of fixes and reliability improvements for selftests
- fix sysfs documentation missing net/ in paths
- finish the work of squashing the missing MODULE_DESCRIPTION()
warnings in networking"
* tag 'net-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits)
net: fill in MODULE_DESCRIPTION()s for missing arcnet
net: fill in MODULE_DESCRIPTION()s for mdio_devres
net: fill in MODULE_DESCRIPTION()s for ppp
net: fill in MODULE_DESCRIPTION()s for fddik/skfp
net: fill in MODULE_DESCRIPTION()s for plip
net: fill in MODULE_DESCRIPTION()s for ieee802154/fakelb
net: fill in MODULE_DESCRIPTION()s for xen-netback
net: ravb: Count packets instead of descriptors in GbEth RX path
pppoe: Fix memory leak in pppoe_sendmsg()
net: sctp: fix skb leak in sctp_inq_free()
net: bcmasp: Handle RX buffer allocation failure
net-timestamp: make sk_tskey more predictable in error path
selftests: tls: increase the wait in poll_partial_rec_async
ice: Add check for lport extraction to LAG init
netfilter: nf_tables: fix bidirectional offload regression
netfilter: nat: restore default DNAT behavior
netfilter: nft_set_pipapo: fix missing : in kdoc
igc: Remove temporary workaround
igb: Fix string truncation warnings in igb_set_fw_version
can: netlink: Fix TDCO calculation using the old data bittiming
...
projects / linux.git / log