Ezequiel Garcia [Fri, 30 May 2014 16:40:05 +0000 (13:40 -0300)]
net: mvneta: Limit the TSO segments and adjust stop/wake thresholds
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.
In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Kristian Evensen [Fri, 30 May 2014 10:17:00 +0000 (12:17 +0200)]
ipheth: Add support for iPad 2 and iPad 3
Each iPad model has a different product id, this patch adds support for iPad 2
(pid 0x12a2) and iPad 3 (pid 0x12a6). Note that iPad 2 must be jailbroken and a
third-party app must be used for tethering to work. On iPad 3, tethering works
out of the box (assuming your ISP is nice).
David S. Miller [Mon, 2 Jun 2014 23:01:37 +0000 (16:01 -0700)]
Merge branch 'cdc_ncm'
Bjørn Mork says:
====================
cdc_ncm: fixes and conversion to sysfs API
After considering the comments received after the ethtool coalesce
support was commited, I have ended up concluding that we should
remove it again, while we can, before it hits a release. The idea
was not well enough thought through, and all comments received
pointed to advantages of using a sysfs based API instead.
This series removes the ethtool coalesce support and replaces it
with sysfs attributes in a driver specific group under the netdev.
The first 3 patches are unrelated fixes:
patch 1: reducing truesize as discussed
patch 2: fixing a potentional buffer overrun when changing tx_max
patch 3: prevent framing errors when changing rx_max
Changes v2:
- minor editorial changes to patch 8, as suggested by Peter Stuge
====================
Bjørn Mork [Fri, 30 May 2014 07:31:09 +0000 (09:31 +0200)]
net: cdc_ncm: allow tuning min_tx_pkt
The min_tx_pkt variable decides the cutoff point where the driver
will stop padding out NTBs to maximum size. The padding is a tradeoff
where we use some USB bus bandwidth to allow the device to receive
fixed size buffers. Different devices will have different optimal
settings, spanning from no padding at all to padding every NTB.
There is no way to automatically figure out which setting is best
for a specific device.
The default value is a reasonable tradeoff, calculated based on the
USB packet size and out NTB max size. This may have to be changed
along with any tx_max changes.
Bjørn Mork [Fri, 30 May 2014 07:31:08 +0000 (09:31 +0200)]
net: cdc_ncm: export NCM Transfer Block (NTB) parameters
The mandatory GetNtbParameters control request is an important part of
the host <-> device protocol negotiation in CDC NCM (and CDC MBIM). It
gives device limits which the host must obey when configuring the
protocol aggregation variables. The driver will enforce this by
rejecting attempts to set any of the tunable variables to a value
which is not supported by the device. Exporting the parameter block
helps userspace decide which values are allowed without resorting
to trial and error.
Bjørn Mork [Fri, 30 May 2014 07:31:07 +0000 (09:31 +0200)]
net: cdc_ncm: drop ethtool coalesce support
The ethtool coalesce API is not applicable for this driver. Forcing
it to fit the NCM aggregation redefined the API in a driver specific
way, which is much worse than defining a clean new API. These ethtool
coalesce functions have therefore been replaced by a new sysfs API.
Bjørn Mork [Fri, 30 May 2014 07:31:06 +0000 (09:31 +0200)]
net: cdc_ncm: use sysfs for rx/tx aggregation tuning
Attach a driver specific sysfs group to the netdev, and use it
for the rx/tx aggregation variables.
The datagram aggregation defined by the CDC NCM specification is
specific to this device class (including CDC MBIM). Using the
ethtool interrupt coalesce API as an interface to the aggregation
parameters redefined that API in a driver specific and confusing
way. A sysfs group
- makes it clear that this is a driver specific userspace API, and
- allows us to export the real values instead of some translated
version, and
- lets us include more aggregation variables which were impossible
to force into the ethtool API.
Additionally, using sysfs allows tuning the driver on space
constrained hosts where userspace tools like ethtool are undesired.
Bjørn Mork [Fri, 30 May 2014 07:31:05 +0000 (09:31 +0200)]
net: cdc_ncm: inform usbnet when rx buffers are reduced
It doesn't matter whether the buffer size goes up or down. We have to
keep usbnet and device syncronized to be able to split transfers at the
correct boundaries. The spec allow skipping short packets when using
max sized transfers. If we don't tell usbnet about our new expected rx
buffer size, then it will merge and/or split NTBs. The driver does not
support this, and the result will be lots of framing errors.
Fix by always reallocating usbnet rx buffers when the rx_max value
changes.
Fixes: 68864abf08f0 ("net: cdc_ncm: support rx_max/tx_max updates when running") Signed-off-by: Bjørn Mork <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Bjørn Mork [Fri, 30 May 2014 07:31:04 +0000 (09:31 +0200)]
net: cdc_ncm: always reallocate tx_curr_skb when tx_max increases
We are calling usbnet_start_xmit() to flush any remaining data,
depending on the side effect that tx_curr_skb is set to NULL,
ensuring a new allocation using the updated tx_max. But this
side effect will only happen if there were any cached data ready
to transmit. If not, then an empty tx_curr_skb is still allocated
using the old tx_max size. Free it to avoid a buffer overrun.
Fixes: 68864abf08f0 ("net: cdc_ncm: support rx_max/tx_max updates when running") Signed-off-by: Bjørn Mork <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Bjørn Mork [Fri, 30 May 2014 07:31:03 +0000 (09:31 +0200)]
net: cdc_ncm: reduce skb truesize in rx path
Cloning the big skbs we use for USB buffering chokes up TCP and
SCTP because the socket memory limits are hitting earlier than
they should. It is better to unconditionally copy the unwrapped
packets to freshly allocated skbs.
dingtianhong [Fri, 30 May 2014 06:32:49 +0000 (14:32 +0800)]
macvlan: fix the problem when mac address changes for passthru mode
The macvlan dev should always have the same mac address like lowerdev
when in the passthru mode, change the mac address alone will break the
work mechanism, so when the lowerdev or macvlan mac address changes,
we should propagate the changes to another dev.
v1->v2: Allow macvlan dev to change mac address for passthru mode and propagate to
lowerdev.
v2->v3: Don't set the mac address to the lower dev's unicast address for
passthru mode when mac address changes.
Jiri Pirko [Thu, 29 May 2014 18:46:17 +0000 (20:46 +0200)]
team: fix mtu setting
Now it is not possible to set mtu to team device which has a port
enslaved to it. The reason is that when team_change_mtu() calls
dev_set_mtu() for port device, notificator for NETDEV_PRECHANGEMTU
event is called and team_device_event() returns NOTIFY_BAD forbidding
the change. So fix this by returning NOTIFY_DONE here in case team is
changing mtu in team_change_mtu().
Introduced-by: 3d249d4c "net: introduce ethernet teaming device" Signed-off-by: Jiri Pirko <[email protected]> Acked-by: Flavio Leitner <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Eric Dumazet [Thu, 29 May 2014 15:45:14 +0000 (08:45 -0700)]
net: fix inet_getid() and ipv6_select_ident() bugs
I noticed we were sending wrong IPv4 ID in TCP flows when MTU discovery
is disabled.
Note how GSO/TSO packets do not have monotonically incrementing ID.
06:37:41.575531 IP (id 14227, proto: TCP (6), length: 4396)
06:37:41.575534 IP (id 14272, proto: TCP (6), length: 65212)
06:37:41.575544 IP (id 14312, proto: TCP (6), length: 57972)
06:37:41.575678 IP (id 14317, proto: TCP (6), length: 7292)
06:37:41.575683 IP (id 14361, proto: TCP (6), length: 63764)
It appears I introduced this bug in linux-3.1.
inet_getid() must return the old value of peer->ip_id_count,
not the new one.
Lets revert this part, and remove the prevention of
a null identification field in IPv6 Fragment Extension Header,
which is dubious and not even done properly.
Fixes: 87c48fa3b463 ("ipv6: make fragment identifications less predictable") Signed-off-by: Eric Dumazet <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Chen-Yu Tsai [Thu, 29 May 2014 14:31:40 +0000 (22:31 +0800)]
net: stmmac: Handle different error codes from platform_get_irq_byname
The following patch moved device tree interrupt resolution into
platform_get_irq_byname:
ad69674 of/irq: do irq resolution in platform_get_irq_byname()
As a result, the function no longer only return -ENXIO on error.
This breaks DT based probing of stmmac, as seen in test runs of
linux-next next-20140526 cubie2-sunxi_defconfig:
This patch makes the stmmac_platform probe function properly handle
error codes, such as returning for deferred probing, and other codes
returned by of_irq_get_by_name.
net: qmi_wwan: interface #11 in Sierra Wireless MC73xx is not QMI
This interface is unusable, as the cdc-wdm character device doesn't reply to
any QMI command. Also, the out-of-tree Sierra Wireless GobiNet driver fully
skips it.
Toshiaki Makita [Mon, 26 May 2014 06:15:53 +0000 (15:15 +0900)]
bridge: Prevent insertion of FDB entry with disallowed vlan
br_handle_local_finish() is allowing us to insert an FDB entry with
disallowed vlan. For example, when port 1 and 2 are communicating in
vlan 10, and even if vlan 10 is disallowed on port 3, port 3 can
interfere with their communication by spoofed src mac address with
vlan id 10.
Note: Even if it is judged that a frame should not be learned, it should
not be dropped because it is destined for not forwarding layer but higher
layer. See IEEE 802.1Q-2011 8.13.10.
Please pull this remaining batch of updates intended for the 3.16 stream...
For the mac80211 bits, Johannes says:
"The remainder for -next right now is mostly fixes, and a handful of
small new things like some CSA infrastructure, the regdb script mW/dBm
conversion change and sending wiphy notifications."
For the bluetooth bits, Gustavo says:
"Some more patches for 3.16. There is nothing really special here, just a
bunch of clean ups, fixes plus some small improvements. Please pull."
For the nfc bits, Samuel says:
"We have:
- Felica (Type3) tags support for trf7970a
- Type 4b tags support for port100
- st21nfca DTS typo fix
- A few sparse warning fixes"
For the atheros bits, Kalle says:
"Ben added support for setting antenna configurations. Michal improved
warm reset so that we would not need to fall back to cold reset that
often, an issue where ath10k stripped protected flag while in monitor
mode and made module initialisation asynchronous to fix the problems
with firmware loading when the driver is linked to the kernel.
Luca removed unused channel_switch_beacon callbacks both from ath9k and
ath10k. Marek fixed Protected Management Frames (PMF) when using Action
Frames. Also we had other small fixes everywhere in the driver."
Along with that, there are a handful of updates to a variety
of drivers. This includes updates to at76c50x-usb, ath9k, b43,
brcmfmac, mwifiex, rsi, rtlwifi, and wil6210.
====================
Eric Dumazet [Mon, 2 Jun 2014 12:26:03 +0000 (05:26 -0700)]
inetpeer: get rid of ip_id_count
Ideally, we would need to generate IP ID using a per destination IP
generator.
linux kernels used inet_peer cache for this purpose, but this had a huge
cost on servers disabling MTU discovery.
1) each inet_peer struct consumes 192 bytes
2) inetpeer cache uses a binary tree of inet_peer structs,
with a nominal size of ~66000 elements under load.
3) lookups in this tree are hitting a lot of cache lines, as tree depth
is about 20.
4) If server deals with many tcp flows, we have a high probability of
not finding the inet_peer, allocating a fresh one, inserting it in
the tree with same initial ip_id_count, (cf secure_ip_id())
5) We garbage collect inet_peer aggressively.
IP ID generation do not have to be 'perfect'
Goal is trying to avoid duplicates in a short period of time,
so that reassembly units have a chance to complete reassembly of
fragments belonging to one message before receiving other fragments
with a recycled ID.
We simply use an array of generators, and a Jenkin hash using the dst IP
as a key.
ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it
belongs (it is only used from this file)
secure_ip_id() and secure_ipv6_id() no longer are needed.
Rename ip_select_ident_more() to ip_select_ident_segs() to avoid
unnecessary decrement/increment of the number of segments.
Daniel Mack [Mon, 2 Jun 2014 11:32:46 +0000 (13:32 +0200)]
of: of_mdio: export symbol of_mdiobus_link_phydev
Make of_mdiobus_link_phydev externally available.
This fixes CONFIG_OF_MDIO=m.
Signed-off-by: Daniel Mack <[email protected]> Reported-by: Stephen Rothwell <[email protected]> Fixes: 86f6cf41272 ("net: of_mdio: add of_mdiobus_link_phydev()") Signed-off-by: David S. Miller <[email protected]>
Daniel Mack [Mon, 2 Jun 2014 11:32:45 +0000 (13:32 +0200)]
net: of_mdio: use int type for address variable
Use int rather than u32 to fix the following warning:
drivers/of/of_mdio.c:147 of_mdiobus_register() warn: unsigned 'addr' is
never less than zero.
Signed-off-by: Daniel Mack <[email protected]> Fixes: 8f8382888cba ("net: of_mdio: factor out code to parse a phy's 'reg' property") Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Mon, 2 Jun 2014 17:41:30 +0000 (10:41 -0700)]
Merge branch 'netdevsync'
Alexander Duyck says:
====================
Provide common means for device address sync
The following series implements a means for synchronizing both unicast and
multicast addresses on a device interface. The code is based on the original
implementation of dev_uc_sync that was available for syncing a VLAN to the
lower dev.
The original reason for coming up for this patch is a driver that is still in
the early stages of development. The nearest driver I could find that
appeared to have the same limitations as the driver I was working on was the
Cisco enic driver. For this reason I chose it as the first driver to make use
of this interface publicly.
However, I do not have a Cisco enic interface so I have only been able to
compile test any changes made to the driver. I tried to keep this change as
simple as possible to avoid any issues. Any help with testing would be
greatly appreciated.
====================
Alexander Duyck [Thu, 29 May 2014 01:44:52 +0000 (18:44 -0700)]
enic: Update driver to use __dev_uc/mc_sync/unsync calls
This change updates the enic driver to make use of __dev_uc_sync and
__dev_mc_sync calls. Previously the driver was doing its own list
management by storing the mc_addr and uc_addr list in a 32 address array.
With this change the sync data is stored in the netdev_addr_list structures
and instead we just track how many addresses we have written to the device.
When we encounter 32 we stop and print a message as occurred previously with
the old approach.
Other than the core change the only other bit needed was to propagate the
constant attribute with the MAC address as there were several spots where
is twas only passed as a u8 * instead of a const u8 *.
This patch is meant to maintain the original functionality without the use
of the mc_addr and uc_addr arrays.
Alexander Duyck [Thu, 29 May 2014 01:44:46 +0000 (18:44 -0700)]
net: Add support for device specific address syncing
This change provides a function to be used in order to break the
ndo_set_rx_mode call into a set of address add and remove calls. The code
is based on the implementation of dev_uc_sync/dev_mc_sync. Since they
essentially do the same thing but with only one dev I simply named my
functions __dev_uc_sync/__dev_mc_sync.
I also implemented an unsync version of the functions as well to allow for
cleanup on close.
David S. Miller [Mon, 2 Jun 2014 17:39:52 +0000 (10:39 -0700)]
Merge branch '6lowpan-next'
Alexander Aring says:
====================
6lowpan: fragmentation fixes
This patch series fix the 6LoWPAN fragmentation which are in two cases broken.
The first case is if we have exactly two 6LoWPAN fragments only. This is fixed
by patch "6lowpan_rtnl: fix fragmentation with two fragments".
The second case is a off by one issue if we have payload which hits the fragment
boundary.
Alexander Aring [Mon, 2 Jun 2014 11:21:58 +0000 (13:21 +0200)]
6lowpan_rtnl: fix off by one while fragmentation
This patch fix a off by one error while fragmentation. If the frag_cap
value is equal to skb_unprocessed value we need to stop the
fragmentation loop because the last fragment which has a size of
skb_unprocessed fits into the frag capability size.
Alexander Aring [Mon, 2 Jun 2014 11:21:57 +0000 (13:21 +0200)]
6lowpan_rtnl: fix fragmentation with two fragments
This patch fix the 6LoWPAN fragmentation for the case if we have exactly
two fragments. The problem is that the (skb_unprocessed >= frag_cap)
condition is always false on the second fragment after sending the first
fragment. A fragmentation with only one fragment doesn't make any sense.
The solution is that we use a do while loop here, that ensures we sending
always a minimum of two fragments if we need a fragmentation.
Emil Goode [Mon, 2 Jun 2014 09:30:50 +0000 (11:30 +0200)]
stmmac: Remove spin_lock call in stmmac_get_pauseparam()
The following patch removed unnecessary spin_lock/unlock calls
in ethtool_ops callback functions. In the second and final version
of the patch one spin_lock call was left behind.
net: driver: stmicro: Remove some useless the lock protection
This introduced the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c:424:1: warning:
context imbalance in 'stmmac_get_pauseparam' -
different lock contexts for basic block
Jukka Taimisto [Thu, 22 May 2014 10:02:39 +0000 (10:02 +0000)]
Bluetooth: Fix L2CAP deadlock
-[0x01 Introduction
We have found a programming error causing a deadlock in Bluetooth subsystem
of Linux kernel. The problem is caused by missing release_sock() call when
L2CAP connection creation fails due full accept queue.
The issue can be reproduced with 3.15-rc5 kernel and is also present in
earlier kernels.
-[0x02 Details
The problem occurs when multiple L2CAP connections are created to a PSM which
contains listening socket (like SDP) and left pending, for example,
configuration (the underlying ACL link is not disconnected between
connections).
When L2CAP connection request is received and listening socket is found the
l2cap_sock_new_connection_cb() function (net/bluetooth/l2cap_sock.c) is called.
This function locks the 'parent' socket and then checks if the accept queue
is full.
1178 lock_sock(parent);
1179
1180 /* Check for backlog size */
1181 if (sk_acceptq_is_full(parent)) {
1182 BT_DBG("backlog full %d", parent->sk_ack_backlog);
1183 return NULL;
1184 }
If case the accept queue is full NULL is returned, but the 'parent' socket
is not released. Thus when next L2CAP connection request is received the code
blocks on lock_sock() since the parent is still locked.
Also note that for connections already established and waiting for
configuration to complete a timeout will occur and l2cap_chan_timeout()
(net/bluetooth/l2cap_core.c) will be called. All threads calling this
function will also be blocked waiting for the channel mutex since the thread
which is waiting on lock_sock() alread holds the channel mutex.
We were able to reproduce this by sending continuously L2CAP connection
request followed by disconnection request containing invalid CID. This left
the created connections pending configuration.
After the deadlock occurs it is impossible to kill bluetoothd, btmon will not
get any more data etc. requiring reboot to recover.
-[0x03 Fix
Releasing the 'parent' socket when l2cap_sock_new_connection_cb() returns NULL
seems to fix the issue.
netfilter: nf_tables: allow to delete several objects from a batch
Three changes to allow the deletion of several objects with dependencies
in one transaction, they are:
1) Introduce speculative counter increment/decrement that is undone in
the abort path if required, thus we avoid hitting -EBUSY when deleting
the chain. The counter updates are reverted in the abort path.
2) Increment/decrement table/chain use counter for each set/rule. We need
this to fully rely on the use counters instead of the list content,
eg. !list_empty(&chain->rules) which evaluate true in the middle of the
transaction.
3) Decrement table use counter when an anonymous set is bound to the
rule in the commit path. This avoids hitting -EBUSY when deleting
the table that contains anonymous sets. The anonymous sets are released
in the nf_tables_rule_destroy path. This should not be a problem since
the rule already bumped the use counter of the chain, so the bound
anonymous set reflects dependencies through the rule object, which
already increases the chain use counter.
So the general assumption after this patch is that the use counters are
bumped by direct object dependencies.
There's no rbtree rcu version yet, so let's fall back on the spinlock
to protect the concurrent access of this structure both from user
(to update the set content) and kernel-space (in the packet path).
netfilter: nf_tables: release objects in reverse order in the abort path
The patch c7c32e7 ("netfilter: nf_tables: defer all object release via
rcu") indicates that we always release deleted objects in the reverse
order, but that is only needed in the abort path. These are the two
possible scenarios when releasing objects:
1) Deletion scenario in the commit path: no need to release objects in
the reverse order since userspace already ensures that dependencies are
fulfilled), ie. userspace tells us to delete rule -> ... -> rule ->
chain -> table. In this case, we have to release the objects in the
*same order* as userspace provided.
2) Deletion scenario in the abort path: we have to iterate in the reverse
order to undo what it cannot be added, ie. userspace sent us a batch
that includes: table -> chain -> rule -> ... -> rule, and that needs to
be partially undone. In this case, we have to release objects in the
reverse order to ensure that the set and chain objects point to valid
rule and table objects.
netfilter: nf_tables: fix wrong transaction ordering in set elements
The transaction needs to be placed at the end of the commit list,
otherwise event notifications are reordered and we may crash when
releasing object via call_rcu.
This problem was introduced in 60319eb ("netfilter: nf_tables: use new
transaction infrastructure to handle elements").
Mathieu Poirier [Mon, 2 Jun 2014 01:42:58 +0000 (19:42 -0600)]
netfilter: nfnetlink_acct: Fix memory leak
Allocation of memory need only to happen once, that is
after the proper checks on the NFACCT_FLAGS have been
done. Otherwise the code can return without freeing
already allocated memory.
Johan Hedberg [Mon, 2 Jun 2014 07:12:44 +0000 (10:12 +0300)]
Bluetooth: Fix missing check for FIPS security level
When checking whether a legacy link key provides at least HIGH security
level we also need to check for FIPS level which is one step above HIGH.
This patch fixes a missing check in the hci_link_key_request_evt()
function.
Stephen Boyd [Wed, 28 May 2014 20:11:12 +0000 (13:11 -0700)]
net: ks8851: Don't use regulator_get_optional()
We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.
David S. Miller [Mon, 2 Jun 2014 05:17:21 +0000 (22:17 -0700)]
Merge branch 'filter-next'
Daniel Borkmann says:
====================
BPF + test suite updates
These are the last bigger BPF changes that I had in my todo
queue for now. As the first two patches from this series
contain additional test cases for the test suite, I have
rebased them on top of current net-next with the set from [1]
applied to avoid introducing any unnecessary merge conflicts.
For details, please refer to the individual patches. Test
suite runs fine with the set applied.
Daniel Borkmann [Thu, 29 May 2014 08:22:51 +0000 (10:22 +0200)]
net: filter: improve filter block macros
Commit 9739eef13c92 ("net: filter: make BPF conversion more readable")
started to introduce helper macros similar to BPF_STMT()/BPF_JUMP()
macros from classic BPF.
However, quite some statements in the filter conversion functions
remained in the old style which gives a mixture of block macros and
non block macros in the code. This patch makes the block macros itself
more readable by using explicit member initialization, and converts
the remaining ones where possible to remain in a more consistent state.
Daniel Borkmann [Thu, 29 May 2014 08:22:50 +0000 (10:22 +0200)]
net: filter: get rid of BPF_S_* enum
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Daniel Borkmann [Thu, 29 May 2014 08:22:49 +0000 (10:22 +0200)]
net: filter: add test for loading SKF_AD_OFF limits
This check tests that overloading BPF_LD | BPF_ABS with an
always invalid BPF extension, that is SKF_AD_MAX, fails to
make sure classic BPF behaviour is correct in filter checker.
Also, we add a test for loading at packet offset SKF_AD_OFF-1
which should pass the filter, but later on fail during runtime.
Daniel Borkmann [Thu, 29 May 2014 08:22:48 +0000 (10:22 +0200)]
net: filter: add slot overlapping test with fully filled M[]
Also add a test for the scratch memory store that first fills
all slots and then sucessively reads all of them back adding
up to A, and eventually returning A. This and the previous
M[] test with alternating fill/spill will detect possible JIT
errors on M[].
Jon Maxwell [Thu, 29 May 2014 07:27:16 +0000 (17:27 +1000)]
bridge: notify user space after fdb update
There has been a number incidents recently where customers running KVM have
reported that VM hosts on different Hypervisors are unreachable. Based on
pcap traces we found that the bridge was broadcasting the ARP request out
onto the network. However some NICs have an inbuilt switch which on occasions
were broadcasting the VMs ARP request back through the physical NIC on the
Hypervisor. This resulted in the bridge changing ports and incorrectly learning
that the VMs mac address was external. As a result the ARP reply was directed
back onto the external network and VM never updated it's ARP cache. This patch
will notify the bridge command, after a fdb has been updated to identify such
port toggling.
wangweidong [Thu, 29 May 2014 02:15:30 +0000 (10:15 +0800)]
bridge: fix the unbalanced promiscuous count when add_if failed
As commit 2796d0c648c94 ("bridge: Automatically manage port
promiscuous mode."), make the add_if use dev_set_allmulti
instead of dev_set_promiscuous, so when add_if failed, we
should do dev_set_allmulti(dev, -1).
Stephen Boyd [Wed, 28 May 2014 20:11:12 +0000 (13:11 -0700)]
net: ks8851: Don't use regulator_get_optional()
We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.
After 1e785f48d29a ("net: Start with correct mac_len in
skb_network_protocol") skb->mac_len is used as a start of the
calculation in skb_network_protocol() but that is not always correct. If
skb->protocol == 8021Q/AD, usually the vlan header is already inserted
in the skb (i.e. vlan reorder hdr == 0). Usually when the packet enters
dev_hard_xmit it has mac_len == 0 so we take 2 bytes from the
destination mac address (skb->data + VLAN_HLEN) as a type in
skb_network_protocol() and return vlan_depth == 4. In the case where TSO is
off, then the mac_len is set but it's == 18 (ETH_HLEN + VLAN_HLEN), so
skb_network_protocol() returns a type from inside the packet and
offset == 22. Also make vlan_depth unsigned as suggested before.
As suggested by Eric Dumazet, move the while() loop in the if() so we
can avoid additional testing in fast path.
Here are few netperf tests + debug printk's to illustrate:
cat netperf.tso-on.reorder-on.bugged
- Vlan -> device (reorder on, default, this case is okay)
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
192.168.3.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
- Vlan -> device (reorder off, bad)
cat netperf.tso-on.reorder-off.bugged
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
192.168.3.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 241.35
[ 204.578332] skb->len 1518 skb->gso_size 0 skb->proto 0x8100
skb->mac_len 0 vlan_depth 4 type 0x5301
0x5301 are the last two bytes of the destination mac.
And if we stop TSO, we may get even the following:
[ 83.343156] skb->len 2966 skb->gso_size 1448 skb->proto 0x8100
skb->mac_len 18 vlan_depth 22 type 0xb84
Because mac_len already accounts for VLAN_HLEN.
After the fix:
cat netperf.tso-on.reorder-off.fixed
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
192.168.3.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
David S. Miller [Mon, 2 Jun 2014 02:17:18 +0000 (19:17 -0700)]
Merge branch 'mlx4-next'
Amir Vadai says:
====================
cpumask,net: Affinity hint helper function
This patchset will set affinity hint to influence IRQs to be allocated on the
same NUMA node as the one where the card resides. As discussed in
http://www.spinics.net/lists/netdev/msg271497.html
If the number of IRQs allocated is greater than the number of local NUMA cores, all
local cores will be used first, and the rest of the IRQs will be on a remote
NUMA node.
If no NUMA support - IRQ's and cores will be mapped 1:1
Since the utility function to calculate the mapping could be useful in other mq
drivers in the kernel, it was added to cpumask.[ch]
This patchset was tested and applied on top of net-next since the first
consumer is a network device (mlx4_en). Over commit 506724c: "tg3: Override
clock, link aware and link idle mode during NVRAM dump"
I couldn't find a maintainer for cpumask.c, so only added the kernel mailing
list
Amir
Changes from V5:
- Moved the utility function from kernel/irq/manage.c to lib/cpumask.c, and
renamed it's name accordingly to cpumask_set_cpu_local_first()
- Added some comments as Thomas Gleixner suggested
- Changed -EINVAL to -EAGAIN, that describes the error situtation better.
Changes from V4:
- Patch 1/2: irq: Utility function to get affinity_hint by policy
Thank you Ben for the great review:
- Moved the function it kernel/irq/manage.c since it could be useful for
block mq devices
- Fixed Typo's
- Use cpumask_t * instead of cpumask_var_t in function header
- Restructured the function to remove NULL assignment in a cpumask_var_t
- Fix for offline local CPU's
Changes from V3:
- Patch 2/2: net/mlx4_en: Use affinity hint
- somehow patch file was corrupted
Changes from V2:
- Patch 1/2: net: Utility function to get affinity_hint by policy
- Fixed style issues
Changes from V1:
- Patch 1/2: net: Utility function to get affinity_hint by policy
- Fixed error flow to return -EINVAL on error (thanks govind)
- Patch 2/2: net/mlx4_en: Use affinity hint
- Set ring->affinity_hint to NULL on error
Changes from V0:
- Fixed small style issues
====================
Yuval Atias [Sun, 25 May 2014 14:47:27 +0000 (17:47 +0300)]
net/mlx4_en: Use affinity hint
The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.
We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it. To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores. If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Amir Vadai [Sun, 25 May 2014 14:47:26 +0000 (17:47 +0300)]
cpumask: Utility function to set n'th cpu - local cpu first
This function sets the n'th cpu - local cpu's first.
For example: in a 16 cores server with even cpu's local, will get the
following values:
cpumask_set_cpu_local_first(0, numa, cpumask) => cpu 0 is set
cpumask_set_cpu_local_first(1, numa, cpumask) => cpu 2 is set
...
cpumask_set_cpu_local_first(7, numa, cpumask) => cpu 14 is set
cpumask_set_cpu_local_first(8, numa, cpumask) => cpu 1 is set
cpumask_set_cpu_local_first(9, numa, cpumask) => cpu 3 is set
...
cpumask_set_cpu_local_first(15, numa, cpumask) => cpu 15 is set
Curently this function will be used by multi queue networking devices to
calculate the irq affinity mask, such that as many local cpu's as
possible will be utilized to handle the mq device irq's.
Linus Torvalds [Mon, 2 Jun 2014 01:28:58 +0000 (18:28 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A fair number of fixes across the field. Nothing terribly
complicated; the one liners in below changelog should be fairly
descriptive.
Noteworthy is the SB1 change which the result of changes to binutils
resulting in one big gas warning for most files being assembled as
well as the asid_cache and branch emulation fixes which fix corruption
or possible uninteded behaviour of kernel or application code. The
remainder of fixes are more platforms or subsystem specific"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: R46000: Fix Micro-assembler field overflow for R4600 V2
MIPS: ptrace: Avoid smp_processor_id() in preemptible code
MIPS: Lemote 2F: cs5536: mfgpt: use raw locks
MIPS: SB1: Fix excessive kernel warnings.
MIPS: RC32434: fix broken PCI resource initialization
MIPS: malta: memory.c: Initialize the 'memsize' variable
MIPS: Fix typo when reporting cache and ftlb errors for ImgTec cores
MIPS: Fix inconsistancy of __NR_Linux_syscalls value
MIPS: Fix branch emulation of branch likely instructions.
MIPS: Fix a typo error in AUDIT_ARCH definition
MIPS: Change type of asid_cache to unsigned long
Linus Torvalds [Mon, 2 Jun 2014 01:26:59 +0000 (18:26 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Various fixlets, mostly related to the (root-only) SCHED_DEADLINE
policy, but also a hotplug bug fix and a fix for a NR_CPUS related
overallocation bug causing a suspend/resume regression"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix hotplug vs. set_cpus_allowed_ptr()
sched/cpupri: Replace NR_CPUS arrays
sched/deadline: Replace NR_CPUS arrays
sched/deadline: Restrict user params max value to 2^63 ns
sched/deadline: Change sched_getparam() behaviour vs SCHED_DEADLINE
sched: Disallow sched_attr::sched_policy < 0
sched: Make sched_setattr() correctly return -EFBIG
Johan Hedberg [Sun, 1 Jun 2014 06:45:24 +0000 (09:45 +0300)]
Bluetooth: Fix requiring SMP MITM for outgoing connections
Due to recent changes to the way that the MITM requirement is set for
outgoing pairing attempts we can no longer rely on the hcon->auth_type
variable (which is actually good since it was formed from BR/EDR
concepts that don't really exist for SMP).
To match the logic that BR/EDR now uses simply rely on the local IO
capability and/or needed security level to set the MITM requirement for
outgoing pairing requests.
here you have another very small fix intended for net/linux-3.15.
It prevents some multicast functions from dereferencing a NULL pointer.
(Actually it was nothing more than a typo)
I hope it is not too late for such a small patch.
====================
Linus Torvalds [Sat, 31 May 2014 16:47:55 +0000 (09:47 -0700)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core futex/rtmutex fixes from Thomas Gleixner:
"Three fixlets for long standing issues in the futex/rtmutex code
unearthed by Dave Jones syscall fuzzer:
- Add missing early deadlock detection checks in the futex code
- Prevent user space from attaching a futex to kernel threads
- Make the deadlock detector of rtmutex work again
Looks large, but is more comments than code change"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Fix deadlock detector for real
futex: Prevent attaching to kernel threads
futex: Add another early deadlock detection check
Linus Torvalds [Sat, 31 May 2014 16:19:02 +0000 (09:19 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Mostly quiet now:
i915:
fixing userspace visiblie issues, all stable marked
radeon:
one more pll fix, two crashers, one suspend/resume regression"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: Resume fbcon last
drm/radeon: only allocate necessary size for vm bo list
drm/radeon: don't allow RADEON_GEM_DOMAIN_CPU for command submission
drm/radeon: avoid crash if VM command submission isn't available
drm/radeon: lower the ref * post PLL maximum once more
drm/i915: Prevent negative relocation deltas from wrapping
drm/i915: Only copy back the modified fields to userspace from execbuffer
drm/i915: Fix dynamic allocation of physical handles
Linus Torvalds [Sat, 31 May 2014 16:13:21 +0000 (09:13 -0700)]
dcache: add missing lockdep annotation
lock_parent() very much on purpose does nested locking of dentries, and
is careful to maintain the right order (lock parent first). But because
it didn't annotate the nested locking order, lockdep thought it might be
a deadlock on d_lock, and complained.
Add the proper annotation for the inner locking of the child dentry to
make lockdep happy.
Introduced by commit 046b961b45f9 ("shrink_dentry_list(): take parent's
->d_lock earlier").
Jukka Rissanen [Tue, 27 May 2014 08:33:22 +0000 (11:33 +0300)]
Bluetooth: 6LoWPAN: Fix MAC address universal/local bit handling
The universal/local bit handling was incorrectly done in the code.
So when setting EUI address from BD address we do this:
- If BD address type is PUBLIC, then we clear the universal bit
in EUI address. If the address type is RANDOM, then the universal
bit is set (BT 6lowpan draft chapter 3.2.2)
- After this we invert the universal/local bit according to RFC 2464
When figuring out BD address we do the reverse:
- Take EUI address from stateless IPv6 address, invert the
universal/local bit according to RFC 2464
- If universal bit is 1 in this modified EUI address, then address
type is set to RANDOM, otherwise it is PUBLIC
Note that 6lowpan_iphc.[ch] does the final toggling of U/L bit
before sending or receiving the network packet.
Johan Hedberg [Fri, 30 May 2014 11:45:19 +0000 (14:45 +0300)]
Bluetooth: Fix authentication check for FIPS security level
When checking whether we need to request authentication or not we should
include HCI_SECURITY_FIPS to the levels that always need authentication.
This patch fixes check for it in the hci_outgoing_auth_needed()
function.
Johan Hedberg [Thu, 29 May 2014 16:36:53 +0000 (19:36 +0300)]
Bluetooth: Fix properly ignoring LTKs of unknown types
In case there are new LTK types in the future we shouldn't just blindly
assume that != MGMT_LTK_UNAUTHENTICATED means that the key is
authenticated. This patch adds explicit checks for each allowed key type
in the form of a switch statement and skips any key which has an unknown
value.
David S. Miller [Sat, 31 May 2014 00:56:09 +0000 (17:56 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
The following patchset contains a late fix for IPVS:
* Fix crash when trying to remove the transport header with non-linear
skbuffs, this was introduced in 3.6-rc. Patch from Peter Christensen
via the IPVS folks.
I'll pass this to -stable once this hits mainstream.
====================
====================
Netfilter/IPVS updates for net-next
This small patchset contains three accumulated Netfilter/IPVS updates,
they are:
1) Refactorize common NAT code by encapsulating it into a helper
function, similarly to what we do in other conntrack extensions,
from Florian Westphal.
2) A minor format string mismatch fix for IPVS, from Masanari Iida.
3) Add quota support to the netfilter accounting infrastructure, now
you can add quotas to accounting objects via the nfnetlink interface
and use them from iptables. You can also listen to quota
notifications from userspace. This enhancement from Mathieu Poirier.
====================
David S. Miller [Sat, 31 May 2014 00:51:27 +0000 (17:51 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and i40evf.
Kevin updates the i40e and i40evf driver i40e_check_asq_alive() to ensure
the length register offset is non-zero which indicates that the software
has initialized the admin queue. Also removes PCTYPE definitions which are
now reserved.
Mitch enables descriptor prefetch for rings belonging to the virtual function.
Also configures the VF minimum transmit rate to 50 Mbps rather than 0 which was
be interpreted as no limit at all. Mitch found in order for the VF to achieve
its programmed transmit rate, we need to set the max credit value to 4.
Lastly fixes a Tx hang and firmware crash that happens after setting the MTU
on a VF by not using the RESETTING state during reinit, this is because
the RESETTING state means that a catastrophic hardware bad thing is happening
and the driver needs to tiptoe around and not use the admin queue or registers.
A reinit is no big deal and we can use the admin queue (and we should) so
do not set the state to RESETTING during reinit to resolve the bug.
Akeem changes the declaration of the transmit and receive rings inside
several loops to eliminate declaring the same ring every time for the
duration of the loop and declares them just once before the loop. Also fixes
the driver to clear the recovery pending bit if pf_reset fails instead of
falling through the setup process.
Anjali makes a change based on feedback from Ben Hutchings that cmd->data
needs to be reported in ETHTOOL_GRXCLSRLCNT and use a helper function to
calculate the total filter count.
Jesse removes storm control since the storm control features are not apart
of the hardware and were mistakenly left in the code.
Greg changes tx_lpi_status and rx_lpi_status from bool to u32 to avoid
sparse errors.
Shannon adds the clear_pxe AdminQ API call to tell the firmware that the
driver is taking over from PXE. In addition, relaxes the firmware API
check to allow more flexibility in handling newer NICs and NVMs in the field.
Vasu ensures that FCoE is disabled for MFP modes since it is not supported
by overriding the hardware FCoE capability.
====================
Ursula Braun [Wed, 28 May 2014 08:22:29 +0000 (10:22 +0200)]
af_iucv: correct cleanup if listen backlog is full
In case of transport HIPER a sock struct is allocated for an incoming
connect request. If the backlog queue is full this socket is not
needed, but is left in the list of af_iucv sockets. Final socket
release posts console message "Attempt to release alive iucv socket".
This patch makes sure the new created socket is cleaned up correctly
if the backlog queue is full.
If a socket is bound to an address using before calling connect
it is usual to leave it to the network system to choose an appropriate
outgoing application name respective port address.
af_iucv on VM uses a counter and uses simple numbers as unique identifiers.
This behaviour was missing when af_iucv is used with HiperSockets.
This patch contains a simple approach to harmonize af_iucv's behaviour.
David S. Miller [Sat, 31 May 2014 00:27:39 +0000 (17:27 -0700)]
Merge branch 'be2net-next'
Sathya Perla says:
====================
be2net: patch set
Patch 1 is a minor optimization for issuing multicast promisc FW cmd
only when the interface is not already in that mode.
Patch 2 provides support for VF TX-rate setting on Skyhawk-R.
Patch 3 provides support for flashing new FW flash regions.
Patches 4, 5, 6 cleanup the MCC processing (for FW cmds) code in be_cmds.c.
The MCC error reporting and event handling code are areas that needed
cleanup.
====================
Sathya Perla [Fri, 30 May 2014 13:36:28 +0000 (19:06 +0530)]
be2net: cleanup MCC async event processing code
The MCC async event processing code has 2 issues:
a) because of long struct names the code indentation is badly broken
b) description and definitions of how an MCC completion is interpreted as
an async event are confusing (for e.g. the last word of an MCC event is
named "code", while "code" is just a sub-field of the last word.)
This patch fixes the structure definitions, comments and re-factors code
as needed.
Sathya Perla [Fri, 30 May 2014 13:36:27 +0000 (19:06 +0530)]
be2net: move async cmd processing to a separate routine
For some FW cmds, the caller just issues the cmd and doesn't wait for a
response. The response handling is done in the MCCQ compl processing context
only. Move this code into a separate routine to make be_mcc_compl_process()
more manageable.
Kalesh AP [Fri, 30 May 2014 13:36:26 +0000 (19:06 +0530)]
be2net: re-factor MCCQ error status handling code
This patch improves MCCQ error status handling in the following ways:
a) A MCC cmd completion returns a base-status and an addl-status.
So far, the routine be_mcc_compl_process() returned only the "status" value.
Now, embedd both statuses in the return value and let the caller routine access
the value of interest using base_status() and addl_status() macros.
b) Rename variables accordingly (base/addl) to avoid confusion while error
checking.
b) Some of the errors returned by FW are harmless and so an error msg is not
logged for such errors. Capture this logic in a separate routine to make the
code more readable.
Vasundhara Volam [Fri, 30 May 2014 13:36:25 +0000 (19:06 +0530)]
be2net: support flashing new regions on Skyhawk-R
Certain new flash regions have been added to Skyhawk-R FW image. The newer
FW images specify op_types for each region. A region is flashed only
when it's CRC doesn't match that of the region on the HW flash. While
upgrading to a new FW image the driver is expected to tolerate certain
errors.
This patch re-factors code under be_flash() to support the above scheme. Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Sathya Perla <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Skyhawk-R FW supports TX-rate setting only as a % value of the link
speed, set via the SET_PROFILE_CONFIG cmd.
This patch makes the necessary changes to the FW cmd descriptors to support
the above change and also introduces checks in be_set_vf_tx_rate() to allow
only discrete values (that map to % of the link-speed).
Kalesh AP [Fri, 30 May 2014 13:36:23 +0000 (19:06 +0530)]
be2net: skip multicast promiscuos setting in already set
Set mc-promisc (multicast promiscuous) mode on an interface, only if it is
*not already* in that mode.
Also removed logs that report interface being set to multicast
promiscous mode. In an earlier comment on the netdev list such log messages
were deemed unnecessary as this behaviour is common across most of the
ethernet drivers.
David S. Miller [Sat, 31 May 2014 00:18:46 +0000 (17:18 -0700)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
Please pull this batch of updates intended for 3.16...
For the mac80211 bits, Johannes says:
"Here I just have Heikki's rfkill GPIO cleanups.
The ARM/tegra patch is OK with the maintainer (Stephen). Let me know of
any problems."
and;
"We have a whole bunch of work on CSA by Andrei, Luca and Michal, but
unfortunately it doesn't seem quite complete yet so it's still disabled.
There's some TDLS work from Arik, and the rest is mostly minor fixes and
cleanups."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones."
For the iwlwifi bits, Emmanuel says:
"Eran continues to work on new devices, Eyal is still digging in
the rate control stuff, and Johannes added new functionality to the
debug system we have in place now along with a few cleanups he made
on the way. That's pretty much it."
and;
"Avri continues to work on the power code and Eran is improving the
NVM handling as a preparations for new devices on which he works
with Liad. Luca cleans up a bit the code while working on CSA. I have
the regular BT Coex stuff and a small lockdep fix. Johannes has his
regular amount of clean ups and improvements, the main one is the
ability to leave 2 chains open to improve diversity and hence the
throughput in high attenuation scenarios."
and;
"The regular amount of housekeeping here. I merged iwlwifi-fixes.git to
be able to add the patch you didn't want in wireless.git at that stage
of the -rc cycle. Luca has a few preparations for CSA implementation
and also what seems to be a bugfix for P2P but hasn't caused issues
we could notice."
For the Atheros bits, Kalle says:
"For ath10k Michal did various small fixes on how we handle
hardware/firmware problems and he also fixed two memory leaks."
Also included are a couple of pulls from the wireless tree to
avoid/resolve merge issues...
====================
Paul Bolle [Tue, 27 May 2014 15:07:12 +0000 (17:07 +0200)]
atm: remove commented out check
This preprocessor check is commented out ever since this file was added
during the v2.3 development cycle. It is unclear what it purpose might
have been. Whatever it was, it can safely be removed now.
Ariel Elior [Tue, 27 May 2014 10:11:36 +0000 (13:11 +0300)]
bnx2x: update MAINTAINERS for bnx2x and e-mail addresses
The bnx2x development team has transferred from Broadcom to Qlogic.
This patch updates some obsolete email addresses to usable ones.
The bnx2x files contain headers with legal information from
Broadcom. Qlogic Legal depratment is taking their time coming up
with their own legal info. So this patch only updates contact
information. I will follow up with a patch for the headers once I
have the required info.
Nimrod Andy [Tue, 27 May 2014 07:51:08 +0000 (15:51 +0800)]
net: fec: use pinctrl PM helpers
when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.
Jack Morgenstein [Tue, 27 May 2014 06:26:38 +0000 (09:26 +0300)]
net/mlx4_core: Reset RoCE VF gids when guest driver goes down
Reset the GIDs assigned to a VF in the port RoCE GID table when
that guest goes down (either crashes or goes down cleanly).
As part of this fix, we refactor the RoCE gid table driver copy,
moving it to the mlx4_port_info structure (together with the MAC
and VLAN tables).
As with the MAC and VLAN tables, we now use a mutex per port
for the GID table so that modifying the driver copy and
modifying the firmware copy of a port GID table becomes an
atomic operation (thus avoiding driver-copy/FW-copy mismatches).
projects / linux.git / log