When the CPU goes idle for the last time during the CPU down hotplug
process, RCU reports a final quiescent state for the current CPU. If
this quiescent state propagates up to the top, some tasks may then be
woken up to complete the grace period: the main grace period kthread
and/or the expedited main workqueue (or kworker).
If those kthreads have a SCHED_FIFO policy, the wake up can indirectly
arm the RT bandwith timer to the local offline CPU. Since this happens
after hrtimers have been migrated at CPUHP_AP_HRTIMERS_DYING stage, the
timer gets ignored. Therefore if the RCU kthreads are waiting for RT
bandwidth to be available, they may never be actually scheduled.
The situation can't be solved with just unpinning the timer. The hrtimer
infrastructure and the nohz heuristics involved in finding the best
remote target for an unpinned timer would then also need to handle
enqueues from an offline CPU in the most horrendous way.
So fix this on the RCU side instead and defer the wake up to an online
CPU if it's too late for the local one.
Reported-by: Paul E. McKenney <[email protected]> Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier") Signed-off-by: Frederic Weisbecker <[email protected]> Signed-off-by: Paul E. McKenney <[email protected]> Signed-off-by: Neeraj Upadhyay (AMD) <[email protected]>
Linus Torvalds [Wed, 24 Jan 2024 16:55:51 +0000 (08:55 -0800)]
Merge tag 'fbdev-for-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes and cleanups from Helge Deller:
"A crash fix in stifb which was missed to be included in the drm-misc
tree, two checks to prevent wrong userspace input in sisfb and
savagefb and two trivial printk cleanups:
- stifb: Fix crash in stifb_blank()
- savage/sis: Error out if pixclock equals zero
- minor trivial cleanups"
* tag 'fbdev-for-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: stifb: Fix crash in stifb_blank()
fbcon: Fix incorrect printed function name in fbcon_prepare_logo()
fbdev: sis: Error out if pixclock equals zero
fbdev: savage: Error out if pixclock equals zero
fbdev: vt8500lcdfb: Remove unnecessary print function dev_err()
NeilBrown [Mon, 22 Jan 2024 03:58:16 +0000 (14:58 +1100)]
nfsd: fix RELEASE_LOCKOWNER
The test on so_count in nfsd4_release_lockowner() is nonsense and
harmful. Revert to using check_for_locks(), changing that to not sleep.
First: harmful.
As is documented in the kdoc comment for nfsd4_release_lockowner(), the
test on so_count can transiently return a false positive resulting in a
return of NFS4ERR_LOCKS_HELD when in fact no locks are held. This is
clearly a protocol violation and with the Linux NFS client it can cause
incorrect behaviour.
If RELEASE_LOCKOWNER is sent while some other thread is still
processing a LOCK request which failed because, at the time that request
was received, the given owner held a conflicting lock, then the nfsd
thread processing that LOCK request can hold a reference (conflock) to
the lock owner that causes nfsd4_release_lockowner() to return an
incorrect error.
The Linux NFS client ignores that NFS4ERR_LOCKS_HELD error because it
never sends NFS4_RELEASE_LOCKOWNER without first releasing any locks, so
it knows that the error is impossible. It assumes the lock owner was in
fact released so it feels free to use the same lock owner identifier in
some later locking request.
When it does reuse a lock owner identifier for which a previous RELEASE
failed, it will naturally use a lock_seqid of zero. However the server,
which didn't release the lock owner, will expect a larger lock_seqid and
so will respond with NFS4ERR_BAD_SEQID.
So clearly it is harmful to allow a false positive, which testing
so_count allows.
The test is nonsense because ... well... it doesn't mean anything.
so_count is the sum of three different counts.
1/ the set of states listed on so_stateids
2/ the set of active vfs locks owned by any of those states
3/ various transient counts such as for conflicting locks.
When it is tested against '2' it is clear that one of these is the
transient reference obtained by find_lockowner_str_locked(). It is not
clear what the other one is expected to be.
In practice, the count is often 2 because there is precisely one state
on so_stateids. If there were more, this would fail.
In my testing I see two circumstances when RELEASE_LOCKOWNER is called.
In one case, CLOSE is called before RELEASE_LOCKOWNER. That results in
all the lock states being removed, and so the lockowner being discarded
(it is removed when there are no more references which usually happens
when the lock state is discarded). When nfsd4_release_lockowner() finds
that the lock owner doesn't exist, it returns success.
The other case shows an so_count of '2' and precisely one state listed
in so_stateid. It appears that the Linux client uses a separate lock
owner for each file resulting in one lock state per lock owner, so this
test on '2' is safe. For another client it might not be safe.
So this patch changes check_for_locks() to use the (newish)
find_any_file_locked() so that it doesn't take a reference on the
nfs4_file and so never calls nfsd_file_put(), and so never sleeps. With
this check is it safe to restore the use of check_for_locks() rather
than testing so_count against the mysterious '2'.
Dinghao Liu [Tue, 28 Nov 2023 09:29:01 +0000 (17:29 +0800)]
net/mlx5e: fix a potential double-free in fs_any_create_groups
When kcalloc() for ft->g succeeds but kvzalloc() for in fails,
fs_any_create_groups() will free ft->g. However, its caller
fs_any_create_table() will free ft->g again through calling
mlx5e_destroy_flow_table(), which will lead to a double-free.
Fix this by setting ft->g to NULL in fs_any_create_groups().
Zhipeng Lu [Wed, 17 Jan 2024 07:17:36 +0000 (15:17 +0800)]
net/mlx5e: fix a double-free in arfs_create_groups
When `in` allocated by kvzalloc fails, arfs_create_groups will free
ft->g and return an error. However, arfs_create_table, the only caller of
arfs_create_groups, will hold this error and call to
mlx5e_destroy_flow_table, in which the ft->g will be freed again.
Leon Romanovsky [Sun, 26 Nov 2023 09:08:10 +0000 (11:08 +0200)]
net/mlx5e: Ignore IPsec replay window values on sender side
XFRM stack doesn't prevent from users to configure replay window
in TX side and strongswan sets replay_window to be 1. It causes
to failures in validation logic when trying to offload the SA.
Replay window is not relevant in TX side and should be ignored.
Fixes: cded6d80129b ("net/mlx5e: Store replay window in XFRM attributes") Signed-off-by: Aya Levin <[email protected]> Signed-off-by: Leon Romanovsky <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
Leon Romanovsky [Tue, 12 Dec 2023 11:52:55 +0000 (13:52 +0200)]
net/mlx5e: Allow software parsing when IPsec crypto is enabled
All ConnectX devices have software parsing capability enabled, but it is
more correct to set allow_swp only if capability exists, which for IPsec
means that crypto offload is supported.
Rahul Rameshbabu [Tue, 28 Nov 2023 22:01:54 +0000 (14:01 -0800)]
net/mlx5: Use mlx5 device constant for selecting CQ period mode for ASO
mlx5 devices have specific constants for choosing the CQ period mode. These
constants do not have to match the constants used by the kernel software
API for DIM period mode selection.
Fixes: cdd04f4d4d71 ("net/mlx5: Add support to create SQ and CQ for ASO") Signed-off-by: Rahul Rameshbabu <[email protected]> Reviewed-by: Jianbo Liu <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
net/mlx5: DR, Use the right GVMI number for drop action
When FW provides ICM addresses for drop RX/TX, the provided capability
is 64 bits that contain its GVMI as well as the ICM address itself.
In case of TX DROP this GVMI is different from the GVMI that the
domain is operating on.
This patch fixes the action to use these GVMI IDs, as provided by FW.
Moshe Shemesh [Sat, 30 Dec 2023 20:40:37 +0000 (22:40 +0200)]
net/mlx5: Bridge, fix multicast packets sent to uplink
To enable multicast packets which are offloaded in bridge multicast
offload mode to be sent also to uplink, FTE bit uplink_hairpin_en should
be set. Add this bit to FTE for the bridge multicast offload rules.
Vlad Buslov [Fri, 10 Nov 2023 10:10:22 +0000 (11:10 +0100)]
net/mlx5e: Fix peer flow lists handling
The cited change refactored mlx5e_tc_del_fdb_peer_flow() to only clear DUP
flag when list of peer flows has become empty. However, if any concurrent
user holds a reference to a peer flow (for example, the neighbor update
workqueue task is updating peer flow's parent encap entry concurrently),
then the flow will not be removed from the peer list and, consecutively,
DUP flag will remain set. Since mlx5e_tc_del_fdb_peers_flow() calls
mlx5e_tc_del_fdb_peer_flow() for every possible peer index the algorithm
will try to remove the flow from eswitch instances that it has never peered
with causing either NULL pointer dereference when trying to remove the flow
peer list head of peer_index that was never initialized or a warning if the
list debug config is enabled[0].
Fix the issue by always removing the peer flow from the list even when not
releasing the last reference to it.
Tariq Toukan [Sun, 5 Nov 2023 15:09:46 +0000 (17:09 +0200)]
net/mlx5e: Fix inconsistent hairpin RQT sizes
The processing of traffic in hairpin queues occurs in HW/FW and does not
involve the cpus, hence the upper bound on max num channels does not
apply to them. Using this bound for the hairpin RQT max_table_size is
wrong. It could be too small, and cause the error below [1]. As the
RQT size provided on init does not get modified later, use the same
value for both actual and max table sizes.
[1]
mlx5_core 0000:08:00.1: mlx5_cmd_out_err:805:(pid 1200): CREATE_RQT(0x916) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x538faf), err(-22)
Fixes: 74a8dadac17e ("net/mlx5e: Preparations for supporting larger number of channels") Signed-off-by: Tariq Toukan <[email protected]> Reviewed-by: Gal Pressman <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
Rahul Rameshbabu [Thu, 23 Nov 2023 02:32:11 +0000 (18:32 -0800)]
net/mlx5e: Fix operation precedence bug in port timestamping napi_poll context
Indirection (*) is of lower precedence than postfix increment (++). Logic
in napi_poll context would cause an out-of-bound read by first increment
the pointer address by byte address space and then dereference the value.
Rather, the intended logic was to dereference first and then increment the
underlying value.
Fixes: 92214be5979c ("net/mlx5e: Update doorbell for port timestamping CQ before the software counter") Signed-off-by: Rahul Rameshbabu <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
Saeed Mahameed [Sat, 16 Dec 2023 03:31:14 +0000 (19:31 -0800)]
net/mlx5e: Use the correct lag ports number when creating TISes
The cited commit moved the code of mlx5e_create_tises() and changed the
loop to create TISes over MLX5_MAX_PORTS constant value, instead of
getting the correct lag ports supported by the device, which can cause
FW errors on devices with less than MLX5_MAX_PORTS ports.
Change that back to mlx5e_get_num_lag_ports(mdev).
Also IPoIB interfaces create there own TISes, they don't use the eth
TISes, pass a flag to indicate that.
This fixes the following errors that might appear in kernel log:
mlx5_cmd_out_err:808:(pid 650): CREATE_TIS(0x912) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x595b5d), err(-22)
mlx5e_create_mdev_resources:174:(pid 650): alloc tises failed, -22
Fixes: b25bd37c859f ("net/mlx5: Move TISes from priv to mdev HW resources") Signed-off-by: Saeed Mahameed <[email protected]>
====================
gve: Alloc before freeing when changing config
Functions allocating resources did so directly into priv thus far. The
assumption doing that was that priv was not already holding references
to live resources.
When ring configuration is changed in any way from userspace, thus far
we relied on calling the ndo_stop and ndo_open callbacks in succession.
This meant that we teardown existing resources and rob the OS of
networking before we have successfully allocated resources for the new
config.
Correcting this requires us to perform allocations without editing priv.
That is what the "gve: Switch to config-aware..." patch does: it modifies
all the allocation paths so that they take a new configuration as input
and return references to newly allocated resources without modifying
priv or interfering with live resources in any way.
Having corrected the allocation paths so, the ndo open and close
callbacks are refactored to make available distinct functions for
allocating queue resources and starting or stopping them. This is then
put to use in the set_channels and set_features hooks in the last two
patches.
These changes have been tested by verifying the integrity of a stream of
integers while the driver is continuously reconfigured with ethtool.
====================
Shailend Chand [Mon, 22 Jan 2024 18:26:32 +0000 (18:26 +0000)]
gve: Alloc before freeing when changing features
Previously, existing queues were being freed before the resources for
the new queues were being allocated. This would take down the interface
if someone were to attempt to change feature flags under a resource
crunch.
Shailend Chand [Mon, 22 Jan 2024 18:26:31 +0000 (18:26 +0000)]
gve: Alloc before freeing when adjusting queues
Previously, existing queues were being freed before the resources for
the new queues were being allocated. This would take down the interface
if someone were to attempt to change queue counts under a resource
crunch.
Shailend Chand [Mon, 22 Jan 2024 18:26:30 +0000 (18:26 +0000)]
gve: Refactor gve_open and gve_close
gve_open is rewritten to be composed of two funcs: gve_queues_mem_alloc
and gve_queues_start. The former only allocates queue resources without
doing anything to install the queues, which is taken up by the latter.
Similarly gve_close is split into gve_queues_stop and
gve_queues_mem_free.
Separating the acts of queue resource allocation and making the queue
become live help with subsequent changes that aim to not take down the
datapath when applying new configurations.
Shailend Chand [Mon, 22 Jan 2024 18:26:29 +0000 (18:26 +0000)]
gve: Switch to config-aware queue allocation
The new config-aware functions will help achieve the goal of being able
to allocate resources for new queues while there already are active
queues serving traffic.
These new functions work off of arbitrary queue allocation configs
rather than just the currently active config in priv, and they return
the newly allocated resources instead of writing them into priv.
Shailend Chand [Mon, 22 Jan 2024 18:26:28 +0000 (18:26 +0000)]
gve: Refactor napi add and remove functions
This change makes the napi poll functions non-static and moves the
gve_(add|remove)_napi functions to gve_utils.c, to make possible future
"start queue" hooks in the datapath files.
Shailend Chand [Mon, 22 Jan 2024 18:26:27 +0000 (18:26 +0000)]
gve: Define config structs for queue allocation
Queue allocation functions currently can only allocate into priv and
free memory in priv. These new structs would be passed into the queue
functions in a subsequent change to make them capable of returning newly
allocated resources and not just writing them into priv. They also make
it possible to allocate resources for queues with a different config
than that of the currently active queues.
Ido Schimmel [Mon, 22 Jan 2024 13:28:43 +0000 (15:28 +0200)]
net/sched: flower: Fix chain template offload
When a qdisc is deleted from a net device the stack instructs the
underlying driver to remove its flow offload callback from the
associated filter block using the 'FLOW_BLOCK_UNBIND' command. The stack
then continues to replay the removal of the filters in the block for
this driver by iterating over the chains in the block and invoking the
'reoffload' operation of the classifier being used. In turn, the
classifier in its 'reoffload' operation prepares and emits a
'FLOW_CLS_DESTROY' command for each filter.
However, the stack does not do the same for chain templates and the
underlying driver never receives a 'FLOW_CLS_TMPLT_DESTROY' command when
a qdisc is deleted. This results in a memory leak [1] which can be
reproduced using [2].
Fix by introducing a 'tmplt_reoffload' operation and have the stack
invoke it with the appropriate arguments as part of the replay.
Implement the operation in the sole classifier that supports chain
templates (flower) by emitting the 'FLOW_CLS_TMPLT_{CREATE,DESTROY}'
command based on whether a flow offload callback is being bound to a
filter block or being unbound from one.
As far as I can tell, the issue happens since cited commit which
reordered tcf_block_offload_unbind() before tcf_block_flush_all_chains()
in __tcf_block_put(). The order cannot be reversed as the filter block
is expected to be freed after flushing all the chains.
[2]
# tc qdisc add dev swp1 clsact
# tc chain add dev swp1 ingress proto ip chain 1 flower dst_ip 0.0.0.0/32
# tc qdisc del dev swp1 clsact
# devlink dev reload pci/0000:06:00.0
Fixes: bbf73830cd48 ("net: sched: traverse chains in block with tcf_get_next_chain()") Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Breno Leitao [Mon, 22 Jan 2024 18:19:55 +0000 (10:19 -0800)]
net/ipv6: resolve warning in ip6_fib.c
In some configurations, the 'iter' variable in function
fib6_repair_tree() is unused, resulting the following warning when
compiled with W=1.
net/ipv6/ip6_fib.c:1781:6: warning: variable 'iter' set but not used [-Wunused-but-set-variable]
1781 | int iter = 0;
| ^
It is unclear what is the advantage of this RT6_TRACE() macro[1], since
users can control pr_debug() in runtime, which is better than at
compilation time. pr_debug() has no overhead when disabled.
Remove the RT6_TRACE() in favor of simple pr_debug() helpers.
Breno Leitao [Mon, 22 Jan 2024 18:19:54 +0000 (10:19 -0800)]
net/ipv6: Remove unnecessary pr_debug() logs
In the ipv6 system, we have some logs basically dumping the name of the
function that is being called. This is not ideal, since ftrace give us
"for free". Moreover, checkpatch is not happy when touching that code:
WARNING: Unnecessary ftrace-like logging - prefer using ftrace
Remove debug functions that only print the current function name.
Michael Kelley [Mon, 22 Jan 2024 16:20:28 +0000 (08:20 -0800)]
hv_netvsc: Calculate correct ring size when PAGE_SIZE is not 4 Kbytes
Current code in netvsc_drv_init() incorrectly assumes that PAGE_SIZE
is 4 Kbytes, which is wrong on ARM64 with 16K or 64K page size. As a
result, the default VMBus ring buffer size on ARM64 with 64K page size
is 8 Mbytes instead of the expected 512 Kbytes. While this doesn't break
anything, a typical VM with 8 vCPUs and 8 netvsc channels wastes 120
Mbytes (8 channels * 2 ring buffers/channel * 7.5 Mbytes/ring buffer).
Unfortunately, the module parameter specifying the ring buffer size
is in units of 4 Kbyte pages. Ideally, it should be in units that
are independent of PAGE_SIZE, but backwards compatibility prevents
changing that now.
Fix this by having netvsc_drv_init() hardcode 4096 instead of using
PAGE_SIZE when calculating the ring buffer size in bytes. Also
use the VMBUS_RING_SIZE macro to ensure proper alignment when running
with page size larger than 4K.
Konrad Dybcio [Mon, 22 Jan 2024 12:02:22 +0000 (13:02 +0100)]
net: ethernet: qualcomm: Remove QDF24xx support
This SoC family was destined for server use, featuring Qualcomm's very
interesting Kryo cores (before "Kryo" became a marketing term for Arm
cores with small modifications). It did however not leave the labs of
Qualcomm and presumably some partners, nor was it ever productized.
Remove the related drivers, as they seem to be long obsolete.
Using skb_ensure_writable_head_tail without a call to skb_unshare causes
the MACsec stack to operate on the original skb rather than a copy in the
macsec_encrypt path. This causes the buffer to be exceeded in space, and
leads to warnings generated by skb_put operations. Opting to revert this
change since skb_copy_expand is more efficient than
skb_ensure_writable_head_tail followed by a call to skb_unshare.
Linus Torvalds [Wed, 24 Jan 2024 00:48:09 +0000 (16:48 -0800)]
Merge tag 'trace-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing and eventfs fixes from Steven Rostedt:
- Fix histogram tracing_map insertion.
The tracing_map_insert copies the value into the elt variable and
then assigns the elt to the entry value. But it is possible that the
entry value becomes visible on other CPUs before the elt is fully
initialized. This is fixed by adding a wmb() between the
initialization of the elt variable and assigning it.
- Have eventfs directory have unique inode numbers.
Having them be all the same proved to be a failure as the 'find'
application will think that the directories are causing loops, as it
checks for directory loops via their inodes. Have the evenfs dir
entries get their inodes assigned when they are referenced and then
save them in the eventfs_inode structure.
* tag 'trace-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
eventfs: Save directory inodes in the eventfs_inode structure
tracing: Ensure visibility when inserting an element into tracing_map
The reason is that commit 2cd3e3772e41 ("x86/cfi,bpf: Fix bpf_struct_ops
CFI") changes the func_addr of arch_prepare_bpf_trampoline in struct_ops
from NULL to non-NULL, while we use func_addr on RV64 to differentiate
between struct_ops and regular trampoline. When the struct_ops testcase
is triggered, it emits wrong prologue and epilogue, and lead to
unpredictable issues. After commit 2cd3e3772e41, we can use
BPF_TRAMP_F_INDIRECT to distinguish them as it always be set in
struct_ops.
Jakub Kicinski [Tue, 23 Jan 2024 16:38:13 +0000 (08:38 -0800)]
Merge tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.8-rc2
The most visible fix here is the ath11k crash fix which was introduced
in v6.7. We also have a fix for iwlwifi memory corruption and few
smaller fixes in the stack.
* tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix race condition on enabling fast-xmit
wifi: iwlwifi: fix a memory corruption
wifi: mac80211: fix potential sta-link leak
wifi: cfg80211/mac80211: remove dependency on non-existing option
wifi: cfg80211: fix missing interfaces when dumping
wifi: ath11k: rely on mac80211 debugfs handling for vif
wifi: p54: fix GCC format truncation warning with wiphy->fw_version
====================
Merge branch 'netfs-fixes' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull netfs fixes from David Howells:
* 'netfs-fixes' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix missing/incorrect unlocking of RCU read lock
afs: Remove afs_dynroot_d_revalidate() as it is redundant
afs: Fix error handling with lookup via FS.InlineBulkStatus
afs: Hide silly-rename files from userspace
cachefiles, erofs: Fix NULL deref in when cachefiles is not doing ondemand-mode
netfs: Fix a NULL vs IS_ERR() check in netfs_perform_write()
netfs, fscache: Prevent Oops in fscache_put_cache()
cifs: Don't use certain unnecessary folio_*() functions
afs: Don't use certain unnecessary folio_*() functions
netfs: Don't use certain unnecessary folio_*() functions
eventfs: Save directory inodes in the eventfs_inode structure
The eventfs inodes and directories are allocated when referenced. But this
leaves the issue of keeping consistent inode numbers and the number is
only saved in the inode structure itself. When the inode is no longer
referenced, it can be freed. When the file that the inode was representing
is referenced again, the inode is once again created, but the inode number
needs to be the same as it was before.
Just making the inode numbers the same for all files is fine, but that
does not work with directories. The find command will check for loops via
the inode number and having the same inode number for directories triggers:
# find /sys/kernel/tracing
find: File system loop detected;
'/sys/kernel/debug/tracing/events/initcall/initcall_finish' is part of the same file system loop as
'/sys/kernel/debug/tracing/events/initcall'.
[..]
Linus pointed out that the eventfs_inode structure ends with a single
32bit int, and on 64 bit machines, there's likely a 4 byte hole due to
alignment. We can use this hole to store the inode number for the
eventfs_inode. All directories in eventfs are represented by an
eventfs_inode and that data structure can hold its inode number.
That last int was also purposely placed at the end of the structure to
prevent holes from within. Now that there's a 4 byte number to hold the
inode, both the inode number and the last integer can be moved up in the
structure for better cache locality, where the llist and rcu fields can be
moved to the end as they are only used when the eventfs_inode is being
deleted.
Eric Dumazet [Mon, 22 Jan 2024 11:26:03 +0000 (11:26 +0000)]
inet_diag: skip over empty buckets
After the removal of inet_diag_table_mutex, sock_diag_table_mutex
and sock_diag_mutex, I was able so see spinlock contention from
inet_diag_dump_icsk() when running 100 parallel invocations.
Eric Dumazet [Mon, 22 Jan 2024 11:26:02 +0000 (11:26 +0000)]
sock_diag: remove sock_diag_mutex
sock_diag_rcv() is still serializing its operations using
a mutex, for no good reason.
This came with commit 0a9c73014415 ("[INET_DIAG]: Fix oops
in netlink_rcv_skb"), but the root cause has been fixed
with commit cd40b7d3983c ("[NET]: make netlink user -> kernel
interface synchronious")
Remove this mutex to let multiple threads run concurrently.
Eric Dumazet [Mon, 22 Jan 2024 11:26:00 +0000 (11:26 +0000)]
sock_diag: allow concurrent operations
sock_diag_broadcast_destroy_work() and __sock_diag_cmd()
are currently using sock_diag_table_mutex to protect
against concurrent sock_diag_handlers[] changes.
This makes inet_diag dump serialized, thus less scalable
than legacy /proc files.
Erick Archer [Fri, 19 Jan 2024 17:16:55 +0000 (18:16 +0100)]
wifi: iwlegacy: Use kcalloc() instead of kzalloc()
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the purpose specific kcalloc() function instead of the argument
size * count in the kzalloc() function.
Also, it is preferred to use sizeof(*pointer) instead of sizeof(type)
due to the type of the variable can change and one needs not change the
former (unlike the latter).
Chih-Kang Chang [Fri, 19 Jan 2024 08:15:01 +0000 (16:15 +0800)]
wifi: rtw89: fix disabling concurrent mode TX hang issue
When disabling concurrent mode and switching to a single interface, the
TX might stuck. The reason is TBTT prohibit area circuit still enable
to block TX. To disable tbtt prohibit area circuit need to delay 2ms to
make it effective. However, we only delay 2us in original code. So we
fix it.
Chih-Kang Chang [Fri, 19 Jan 2024 08:15:00 +0000 (16:15 +0800)]
wifi: rtw89: fix HW scan timeout due to TSF sync issue
When STA connects to an AP and doesn't receive any beacon yet, the
hardware scan is triggered. This scan begins with the default TSF
value. Once STA receives a beacon when switches back to the operating
channel, its TSF synchronizes with the AP. However, if there is a
significant difference in TSF values between the default value and
the synchronized value, it will cause firmware fail to trigger
interrupt, and the C2H won't be sent out. As a result, the scan
continues until a timeout occurs. To fix this issue, we disable TSF
synchronization during scanning to prevent drastic TSF changes, and
enable TSF synchronization after scan.
Po-Hao Huang [Fri, 19 Jan 2024 08:14:56 +0000 (16:14 +0800)]
wifi: rtw89: Set default CQM config if not present
When wpa_supplicant is initiated by users and not by NetworkManager,
the CQM configuration might not be set. Without this setting, ICs
with connection monitor handled by driver won't detect connection
loss. To fix this we prepare a default setting upon associated at
first, then update again if any is given later.
Po-Hao Huang [Fri, 19 Jan 2024 08:14:55 +0000 (16:14 +0800)]
wifi: rtw89: refine hardware scan C2H events
Define struct for scan offload C2H events and update each elements'
bitfield. This patch does not change original behavior, just style
conversion and naming changes.
Chung-Hsuan Hung [Sat, 20 Jan 2024 00:38:31 +0000 (08:38 +0800)]
wifi: rtw89: 8922a: add BTG functions to assist BT coexistence to control TX/RX
These functions are to control baseband AGC while BT coexists with WiFi.
Among these functions, ctrl_btg_bt_rx is used to control AGC related
settings, which is affected by BT RX, while BT shares the same path with
WiFi; ctrl_nbtg_bt_tx is used to control AGC settings under non-shared
path condition, which is affected by BT TX.
Ping-Ke Shih [Sat, 20 Jan 2024 00:38:30 +0000 (08:38 +0800)]
wifi: rtw89: 8922a: add TX power related ops
The ::power_trim is to write bias value programmed in efuse to normalize
TX power, and then using ::set_txpwr_ctrl to set reference TX power value.
The ::set_txpwr is to set final TX power according to regulation of current
country.
Ping-Ke Shih [Sat, 20 Jan 2024 00:38:29 +0000 (08:38 +0800)]
wifi: rtw89: 8922a: add register definitions of H2C, C2H, page, RRSR and EDCCA
Firmware H2C commands and C2H events can go via registers, so define them
accordingly. The page registers are to arrange local buffer of WiFi chip.
RRSR is to define rate selection to transmit BA or ACK. EDCCA is to set
threshold of engine detection mechanism by BB hardware.
Like other chips, define these registers and we can share the same flow.
Ping-Ke Shih [Sat, 20 Jan 2024 00:38:28 +0000 (08:38 +0800)]
wifi: rtw89: 8922a: add chip_ops related to BB init
The chip_ops::bb_preinit and ::bb_postinit are called before and after
loading BB parameters from tables of firmware file. The ::bb_reset is
used to reset hardware state, and currently it is not needed by 8922AE so
leave it as empty. The ::bb_sethw is to implement conditional parameters.
When we are going to up interface to make connection, turn on BB and RF
hardware power by enable_bb_rf ops. Oppositely, using disable_bb_rf to
turn them off.
Ping-Ke Shih [Sat, 20 Jan 2024 00:38:26 +0000 (08:38 +0800)]
wifi: rtw89: add mlo_dbcc_mode for WiFi 7 chips
WiFi 7 chips can operate in various MLO applications, such as 1 link (2SS)
and 2 links (1SS + 1SS), and we should configure different PHY mode for
each of them.
For example,
- MLO_2_PLUS_0_1RF is 1 link with 2SS rate, and enable one RF component.
- MLO_1_PLUS_1_1RF is 2 links with 1SS rate for each, and enable one RF
component that can support two paths.
By default, we set the mode to legacy MLO_DBCC_NOT_SUPPORT (don't support
MLO and DBCC yet), and later we will introduce logic to change the mode.
Amir Goldstein [Sat, 20 Jan 2024 10:18:39 +0000 (12:18 +0200)]
ovl: mark xwhiteouts directory with overlay.opaque='x'
An opaque directory cannot have xwhiteouts, so instead of marking an
xwhiteouts directory with a new xattr, overload overlay.opaque xattr
for marking both opaque dir ('y') and xwhiteouts dir ('x').
This is more efficient as the overlay.opaque xattr is checked during
lookup of directory anyway.
This also prevents unnecessary checking the xattr when reading a
directory without xwhiteouts, i.e. most of the time.
Note that the xwhiteouts marker is not checked on the upper layer and
on the last layer in lowerstack, where xwhiteouts are not expected.
Zhengchao Shao [Mon, 22 Jan 2024 01:18:07 +0000 (09:18 +0800)]
netlink: fix potential sleeping issue in mqueue_flush_file
I analyze the potential sleeping issue of the following processes:
Thread A Thread B
... netlink_create //ref = 1
do_mq_notify ...
sock = netlink_getsockbyfilp ... //ref = 2
info->notify_sock = sock; ...
... netlink_sendmsg
... skb = netlink_alloc_large_skb //skb->head is vmalloced
... netlink_unicast
... sk = netlink_getsockbyportid //ref = 3
... netlink_sendskb
... __netlink_sendskb
... skb_queue_tail //put skb to sk_receive_queue
... sock_put //ref = 2
... ...
... netlink_release
... deferred_put_nlk_sk //ref = 1
mqueue_flush_file
spin_lock
remove_notification
netlink_sendskb
sock_put //ref = 0
sk_free
...
__sk_destruct
netlink_sock_destruct
skb_queue_purge //get skb from sk_receive_queue
...
__skb_queue_purge_reason
kfree_skb_reason
__kfree_skb
...
skb_release_all
skb_release_head_state
netlink_skb_destructor
vfree(skb->head) //sleeping while holding spinlock
In netlink_sendmsg, if the memory pointed to by skb->head is allocated by
vmalloc, and is put to sk_receive_queue queue, also the skb is not freed.
When the mqueue executes flush, the sleeping bug will occur. Use
vfree_atomic instead of vfree in netlink_skb_destructor to solve the issue.
selftest: Don't reuse port for SO_INCOMING_CPU test.
Jakub reported that ASSERT_EQ(cpu, i) in so_incoming_cpu.c seems to
fire somewhat randomly.
# # RUN so_incoming_cpu.before_reuseport.test3 ...
# # so_incoming_cpu.c:191:test3:Expected cpu (32) == i (0)
# # test3: Test terminated by assertion
# # FAIL so_incoming_cpu.before_reuseport.test3
# not ok 3 so_incoming_cpu.before_reuseport.test3
When the test failed, not-yet-accepted CLOSE_WAIT sockets received
SYN with a "challenging" SEQ number, which was sent from an unexpected
CPU that did not create the receiver.
The test basically does:
1. for each cpu:
1-1. create a server
1-2. set SO_INCOMING_CPU
2. for each cpu:
2-1. set cpu affinity
2-2. create some clients
2-3. let clients connect() to the server on the same cpu
2-4. close() clients
3. for each server:
3-1. accept() all child sockets
3-2. check if all children have the same SO_INCOMING_CPU with the server
The root cause was the close() in 2-4. and net.ipv4.tcp_tw_reuse.
In a loop of 2., close() changed the client state to FIN_WAIT_2, and
the peer transitioned to CLOSE_WAIT.
In another loop of 2., connect() happened to select the same port of
the FIN_WAIT_2 socket, and it was reused as the default value of
net.ipv4.tcp_tw_reuse is 2.
As a result, the new client sent SYN to the CLOSE_WAIT socket from
a different CPU, and the receiver's sk_incoming_cpu was overwritten
with unexpected CPU ID.
Also, the SYN had a different SEQ number, so the CLOSE_WAIT socket
responded with Challenge ACK. The new client properly returned RST
and effectively killed the CLOSE_WAIT socket.
This way, all clients were created successfully, but the error was
detected later by 3-2., ASSERT_EQ(cpu, i).
To avoid the failure, let's make sure that (i) the number of clients
is less than the number of available ports and (ii) such reuse never
happens.
On CPUs with weak memory models, reads and updates performed by tcp_push
to the sk variables can get reordered leaving the socket throttled when
it should not. The tasklet running tcp_wfree() may also not observe the
memory updates in time and will skip flushing any packets throttled by
tcp_push(), delaying the sending. This can pathologically cause 40ms
extra latency due to bad interactions with delayed acks.
Adding a memory barrier in tcp_push removes the bug, similarly to the
previous commit bf06200e732d ("tcp: tsq: fix nonagle handling").
smp_mb__after_atomic() is used to not incur in unnecessary overhead
on x86 since not affected.
Patch has been tested using an AWS c7g.2xlarge instance with Ubuntu
22.04 and Apache Tomcat 9.0.83 running the basic servlet below:
public class HelloWorldServlet extends HttpServlet {
@Override
protected void doGet(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
response.setContentType("text/html;charset=utf-8");
OutputStreamWriter osw = new OutputStreamWriter(response.getOutputStream(),"UTF-8");
String s = "a".repeat(3096);
osw.write(s,0,s.length());
osw.flush();
}
}
Load was applied using wrk2 (https://github.com/kinvolk/wrk2) from an AWS
c6i.8xlarge instance. Before the patch an additional 40ms latency from P99.99+
values is observed while, with the patch, the extra latency disappears.
No patch and tcp_autocorking=1
./wrk -t32 -c128 -d40s --latency -R10000 http://172.31.60.173:8080/hello/hello
...
50.000% 0.91ms
75.000% 1.13ms
90.000% 1.46ms
99.000% 1.74ms
99.900% 1.89ms
99.990% 41.95ms <<< 40+ ms extra latency
99.999% 48.32ms
100.000% 48.96ms
With patch and tcp_autocorking=1
./wrk -t32 -c128 -d40s --latency -R10000 http://172.31.60.173:8080/hello/hello
...
50.000% 0.90ms
75.000% 1.13ms
90.000% 1.45ms
99.000% 1.72ms
99.900% 1.83ms
99.990% 2.11ms <<< no 40+ ms extra latency
99.999% 2.53ms
100.000% 2.62ms
Patch has been also tested on x86 (m7i.2xlarge instance) which it is not
affected by this issue and the patch doesn't introduce any additional
delay.
Helge Deller [Mon, 22 Jan 2024 20:26:33 +0000 (21:26 +0100)]
fbdev: stifb: Fix crash in stifb_blank()
Avoid a kernel crash in stifb by providing the correct pointer to the fb_info
struct. Prior to commit e2e0b838a184 ("video/sticore: Remove info field from
STI struct") the fb_info struct was at the beginning of the fb struct.
Fixes: e2e0b838a184 ("video/sticore: Remove info field from STI struct") Signed-off-by: Helge Deller <[email protected]> Cc: Thomas Zimmermann <[email protected]>
David Howells [Tue, 2 Jan 2024 14:02:37 +0000 (14:02 +0000)]
afs: Fix error handling with lookup via FS.InlineBulkStatus
When afs does a lookup, it tries to use FS.InlineBulkStatus to preemptively
look up a bunch of files in the parent directory and cache this locally, on
the basis that we might want to look at them too (for example if someone
does an ls on a directory, they may want want to then stat every file
listed).
FS.InlineBulkStatus can be considered a compound op with the normal abort
code applying to the compound as a whole. Each status fetch within the
compound is then given its own individual abort code - but assuming no
error that prevents the bulk fetch from returning the compound result will
be 0, even if all the constituent status fetches failed.
At the conclusion of afs_do_lookup(), we should use the abort code from the
appropriate status to determine the error to return, if any - but instead
it is assumed that we were successful if the op as a whole succeeded and we
return an incompletely initialised inode, resulting in ENOENT, no matter
the actual reason. In the particular instance reported, a vnode with no
permission granted to be accessed is being given a UAEACCES abort code
which should be reported as EACCES, but is instead being reported as
ENOENT.
Fix this by abandoning the inode (which will be cleaned up with the op) if
file[1] has an abort code indicated and turn that abort code into an error
instead.
Whilst we're at it, add a tracepoint so that the abort codes of the
individual subrequests of FS.InlineBulkStatus can be logged. At the moment
only the container abort code can be 0.
David Howells [Mon, 8 Jan 2024 17:22:36 +0000 (17:22 +0000)]
afs: Hide silly-rename files from userspace
There appears to be a race between silly-rename files being created/removed
and various userspace tools iterating over the contents of a directory,
leading to such errors as:
find: './kernel/.tmp_cpio_dir/include/dt-bindings/reset/.__afs2080': No such file or directory
tar: ./include/linux/greybus/.__afs3C95: File removed before we read it
when building a kernel.
Fix afs_readdir() so that it doesn't return .__afsXXXX silly-rename files
to userspace. This doesn't stop them being looked up directly by name as
we need to be able to look them up from within the kernel as part of the
silly-rename algorithm.
David Howells [Fri, 19 Jan 2024 20:49:34 +0000 (20:49 +0000)]
cachefiles, erofs: Fix NULL deref in when cachefiles is not doing ondemand-mode
cachefiles_ondemand_init_object() as called from cachefiles_open_file() and
cachefiles_create_tmpfile() does not check if object->ondemand is set
before dereferencing it, leading to an oops something like:
Petr Pavlu [Mon, 22 Jan 2024 15:09:28 +0000 (16:09 +0100)]
tracing: Ensure visibility when inserting an element into tracing_map
Running the following two commands in parallel on a multi-processor
AArch64 machine can sporadically produce an unexpected warning about
duplicate histogram entries:
$ while true; do
echo hist:key=id.syscall:val=hitcount > \
/sys/kernel/debug/tracing/events/raw_syscalls/sys_enter/trigger
cat /sys/kernel/debug/tracing/events/raw_syscalls/sys_enter/hist
sleep 0.001
done
$ stress-ng --sysbadaddr $(nproc)
The "memcpy(elt->key, key, map->key_size);" and "entry->val = elt;"
stores may become visible in the reversed order on another CPU. This
second CPU might then incorrectly determine that a new key doesn't match
an already present val->key and subsequently insert a new element,
resulting in a duplicate.
Fix the problem by adding a write barrier between
"memcpy(elt->key, key, map->key_size);" and "entry->val = elt;", and for
good measure, also use WRITE_ONCE(entry->val, elt) for publishing the
element. The sequence pairs with the mentioned "READ_ONCE(entry->val);"
and the "val->key" check which has an address dependency.
The barrier is placed on a path executed when adding an element for
a new key. Subsequent updates targeting the same key remain unaffected.
From the user's perspective, the issue was introduced by commit c193707dde77 ("tracing: Remove code which merges duplicates"), which
followed commit cbf4100efb8f ("tracing: Add support to detect and avoid
duplicates"). The previous code operated differently; it inherently
expected potential races which result in duplicates but merged them
later when they occurred.
David Howells [Tue, 9 Jan 2024 17:54:35 +0000 (17:54 +0000)]
cifs: Don't use certain unnecessary folio_*() functions
Filesystems should use folio->index and folio->mapping, instead of
folio_index(folio), folio_mapping() and folio_file_mapping() since
they know that it's in the pagecache.
David Howells [Tue, 9 Jan 2024 17:51:08 +0000 (17:51 +0000)]
afs: Don't use certain unnecessary folio_*() functions
Filesystems should use folio->index and folio->mapping, instead of
folio_index(folio), folio_mapping() and folio_file_mapping() since
they know that it's in the pagecache.
David Howells [Tue, 9 Jan 2024 17:17:36 +0000 (17:17 +0000)]
netfs: Don't use certain unnecessary folio_*() functions
Filesystems should use folio->index and folio->mapping, instead of
folio_index(folio), folio_mapping() and folio_file_mapping() since
they know that it's in the pagecache.
fbcon: Fix incorrect printed function name in fbcon_prepare_logo()
If the boot logo does not fit, a message is printed, including a wrong
function name prefix. Instead of correcting the function name (or using
__func__), just use "fbcon", like is done in several other messages.
While at it, modernize the call by switching to pr_info().
Linus Torvalds [Mon, 22 Jan 2024 21:29:42 +0000 (13:29 -0800)]
Merge tag 'for-6.8-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- zoned mode fixes:
- fix slowdown when writing large file sequentially by looking up
block groups with enough space faster
- locking fixes when activating a zone
- new mount API fixes:
- preserve mount options for a ro/rw mount of the same subvolume
- scrub fixes:
- fix use-after-free in case the chunk length is not aligned to
64K, this does not happen normally but has been reported on
images converted from ext4
- similar alignment check was missing with raid-stripe-tree
- subvolume deletion fixes:
- prevent calling ioctl on already deleted subvolume
- properly track flag tracking a deleted subvolume
- in subpage mode, fix decompression of an inline extent (zlib, lzo,
zstd)
- fix crash when starting writeback on a folio, after integration with
recent MM changes this needs to be started conditionally
- reject unknown flags in defrag ioctl
- error handling, API fixes, minor warning fixes
* tag 'for-6.8-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: scrub: limit RST scrub to chunk boundary
btrfs: scrub: avoid use-after-free when chunk length is not 64K aligned
btrfs: don't unconditionally call folio_start_writeback in subpage
btrfs: use the original mount's mount options for the legacy reconfigure
btrfs: don't warn if discard range is not aligned to sector
btrfs: tree-checker: fix inline ref size in error messages
btrfs: zstd: fix and simplify the inline extent decompression
btrfs: lzo: fix and simplify the inline extent decompression
btrfs: zlib: fix and simplify the inline extent decompression
btrfs: defrag: reject unknown flags of btrfs_ioctl_defrag_range_args
btrfs: avoid copying BTRFS_ROOT_SUBVOL_DEAD flag to snapshot of subvolume being deleted
btrfs: don't abort filesystem when attempting to snapshot deleted subvolume
btrfs: zoned: fix lock ordering in btrfs_zone_activate()
btrfs: fix unbalanced unlock of mapping_tree_lock
btrfs: ref-verify: free ref cache before clearing mount opt
btrfs: fix kvcalloc() arguments order in btrfs_ioctl_send()
btrfs: zoned: optimize hint byte for zoned allocator
btrfs: zoned: factor out prepare_allocation_zoned()
Bernd Edlinger [Mon, 22 Jan 2024 18:34:21 +0000 (19:34 +0100)]
exec: Fix error handling in begin_new_exec()
If get_unused_fd_flags() fails, the error handling is incomplete because
bprm->cred is already set to NULL, and therefore free_bprm will not
unlock the cred_guard_mutex. Note there are two error conditions which
end up here, one before and one after bprm->cred is cleared.
Consolidate the calls to allow_write_access()/fput() into a single
place, since we repeat this code pattern. Add comments around the
callers for the details on it.
Linus Torvalds [Mon, 22 Jan 2024 17:47:24 +0000 (09:47 -0800)]
Merge tag 'Wstringop-overflow-for-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull stringop-overflow warning update from Gustavo A. R. Silva:
"Enable -Wstringop-overflow globally.
I waited for the release of -rc1 to run a final build-test on top of
it before sending this pull request. Fortunatelly, after building 358
kernels overnight (basically all supported archs with a wide variety
of configs), no more warnings have surfaced! :)
Thus, we are in a good position to enable this compiler option for all
versions of GCC that support it, with the exception of GCC-11, which
appears to have some issues with this option [1]"
Link: https://lore.kernel.org/lkml/[email protected]/
* tag 'Wstringop-overflow-for-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
init: Kconfig: Disable -Wstringop-overflow for GCC-11
Makefile: Enable -Wstringop-overflow globally
Linus Torvalds [Mon, 22 Jan 2024 17:40:05 +0000 (09:40 -0800)]
Merge tag 'xsa448-6.8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen netback fix from Juergen Gross:
"Transmit requests in Xen's virtual network protocol can consist of
multiple parts. While not really useful, except for the initial part
any of them may be of zero length, i.e. carry no data at all.
Besides a certain initial portion of the to be transferred data, these
parts are directly translated into what Linux calls SKB fragments.
Such converted request parts can, when for a particular SKB they are
all of length zero, lead to a de-reference of NULL in core networking
code"
* tag 'xsa448-6.8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-netback: don't produce zero-size SKB frags
net/rds: Fix UBSAN: array-index-out-of-bounds in rds_cmsg_recv
Syzcaller UBSAN crash occurs in rds_cmsg_recv(),
which reads inc->i_rx_lat_trace[j + 1] with index 4 (3 + 1),
but with array size of 4 (RDS_RX_MAX_TRACES).
Here 'j' is assigned from rs->rs_rx_trace[i] and in-turn from
trace.rx_trace_pos[i] in rds_recv_track_latency(),
with both arrays sized 3 (RDS_MSG_RX_DGRAM_TRACE_MAX). So fix the
off-by-one bounds check in rds_recv_track_latency() to prevent
a potential crash in rds_cmsg_recv().
Found by syzcaller:
=================================================================
UBSAN: array-index-out-of-bounds in net/rds/recv.c:585:39
index 4 is out of range for type 'u64 [4]'
CPU: 1 PID: 8058 Comm: syz-executor228 Not tainted 6.6.0-gd2f51b3516da #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.15.0-1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x136/0x150 lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:217 [inline]
__ubsan_handle_out_of_bounds+0xd5/0x130 lib/ubsan.c:348
rds_cmsg_recv+0x60d/0x700 net/rds/recv.c:585
rds_recvmsg+0x3fb/0x1610 net/rds/recv.c:716
sock_recvmsg_nosec net/socket.c:1044 [inline]
sock_recvmsg+0xe2/0x160 net/socket.c:1066
__sys_recvfrom+0x1b6/0x2f0 net/socket.c:2246
__do_sys_recvfrom net/socket.c:2264 [inline]
__se_sys_recvfrom net/socket.c:2260 [inline]
__x64_sys_recvfrom+0xe0/0x1b0 net/socket.c:2260
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
==================================================================
Fixes: 3289025aedc0 ("RDS: add receive message trace used by application") Reported-by: Chenyuan Yang <[email protected]> Closes: https://lore.kernel.org/linux-rdma/CALGdzuoVdq-wtQ4Az9iottBqC5cv9ZhcE5q8N7LfYFvkRsOVcw@mail.gmail.com/ Signed-off-by: Sharath Srinivasan <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Horatiu Vultur [Fri, 19 Jan 2024 10:47:50 +0000 (11:47 +0100)]
net: micrel: Fix PTP frame parsing for lan8814
The HW has the capability to check each frame if it is a PTP frame,
which domain it is, which ptp frame type it is, different ip address in
the frame. And if one of these checks fail then the frame is not
timestamp. Most of these checks were disabled except checking the field
minorVersionPTP inside the PTP header. Meaning that once a partner sends
a frame compliant to 8021AS which has minorVersionPTP set to 1, then the
frame was not timestamp because the HW expected by default a value of 0
in minorVersionPTP. This is exactly the same issue as on lan8841.
Fix this issue by removing this check so the userspace can decide on this.
Fix issues when performing unordered unbind/bind of a kernel modules
which are using a dpll device with DPLL_PIN_TYPE_MUX pins.
Currently only serialized bind/unbind of such use case works, fix
the issues and allow for unserialized kernel module bind order.
dpll: fix register pin with unregistered parent pin
In case of multiple kernel module instances using the same dpll device:
if only one registers dpll device, then only that one can register
directly connected pins with a dpll device. When unregistered parent is
responsible for determining if the muxed pin can be registered with it
or not, the drivers need to be loaded in serialized order to work
correctly - first the driver instance which registers the direct pins
needs to be loaded, then the other instances could register muxed type
pins.
Allow registration of a pin with a parent even if the parent was not
yet registered, thus allow ability for unserialized driver instance
load order.
Do not WARN_ON notification for unregistered pin, which can be invoked
for described case, instead just return error.
Fixes: 9431063ad323 ("dpll: core: Add DPLL framework base functions") Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions") Reviewed-by: Jan Glaza <[email protected]> Reviewed-by: Jiri Pirko <[email protected]> Signed-off-by: Arkadiusz Kubalewski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
If parent pin was unregistered but child pin was not, the userspace
would see the "zombie" pins - the ones that were registered with
a parent pin (dpll_pin_on_pin_register(..)).
Technically those are not available - as there is no dpll device in the
system. Do not dump those pins and prevent userspace from any
interaction with them. Provide a unified function to determine if the
pin is available and use it before acting/responding for user requests.
When a kernel module is unbound but the pin resources were not entirely
freed (other kernel module instance of the same PCI device have had kept
the reference to that pin), and kernel module is again bound, the pin
properties would not be updated (the properties are only assigned when
memory for the pin is allocated), prop pointer still points to the
kernel module memory of the kernel module which was deallocated on the
unbind.
If the pin dump is invoked in this state, the result is a kernel crash.
Prevent the crash by storing persistent pin properties in dpll subsystem,
copy the content from the kernel module when pin is allocated, instead of
using memory of the kernel module.
Fixes: 9431063ad323 ("dpll: core: Add DPLL framework base functions") Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions") Reviewed-by: Jan Glaza <[email protected]> Reviewed-by: Przemek Kitszel <[email protected]> Signed-off-by: Arkadiusz Kubalewski <[email protected]> Reviewed-by: Jiri Pirko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
If pin type is not expected, or pin properities failed to allocate
memory, the unwind error path shall not destroy pin's xarrays, which
were not yet initialized.
Add new goto label and use it to fix broken error path.
David S. Miller [Mon, 22 Jan 2024 10:58:05 +0000 (10:58 +0000)]
Merge branch 'tun-fixes'
Yunjian Wang says:
====================
fixes for tun
There are few places on the receive path where packet receives and
packet drops were not accounted for. This patchset fixes that issue.
====================
projects / linux.git / log