Commit b9562545ef0b ("bcma: complete workaround for BCMA43224 and
BCM4313") introduced the wrong masks for setting the chip control
registers - the "mask" parameter is inverse.
It should be the mask of bits *not* changed, which is admittedly a bit
non-intuitive.
The incorrect mask not only causes the driver to not work correctly on
the chips affected (eg the BCM43224 on the Macbook Air 4,2) but the
state persists over a soft reset, causing the next boot to not
necessarily see the device correctly.
This should fix the problem reported by Fengguang:
The coccinelle static checker emits these warnings:
drivers/bcma/scan.c:466:3-9: ERROR: missing iounmap; ioremap on line 451 and execution via conditional on line 465
drivers/bcma/scan.c:540:3-9: ERROR: missing iounmap; ioremap on line 515 and execution via conditional on line 539
This should be fixed properly later so that the correct interrupt
numbers are assigned to the cores independently from the ordering of
the list. This patch restores the old behavior again. I will look into
the problem more deeply later.
I also changed the order of the list with the cores and their assigned
interrupt number which gets printed to the log. Now they are printed in
the same order like all the other lists of cores and like it was done
before the patch which changed the order.
Merge tag 'char-misc-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg Kroah-Hartman:
"Here's the "big" pull request for 3.6-rc1 for the char/misc drivers.
It's really just a few updates to the mei driver, plus 4 other tiny
patches, nothing big at all.
Signed-off-by: Greg Kroah-Hartman <[email protected]>"
* tag 'char-misc-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: use module_pci_driver
powerpc/BSR: cleanup the error path of bsr_init
mei: mei_irq_thread_write_handler - line break fix
mei: streamline the _mei_irq_thread_close/ioctol functions
mei: introduce mei_data2slots wrapper
mei: mei_wd_host_init: update the comment
mei: remove write only wariable wd_due_counter
mei: mei_device can be const for mei register access functions
mei: revamp host buffer interface function
mei: don't query HCSR for host buffer depth
mei: group wd_interface_reg with watchdog variables within struct mei_device
mei: mei_irq_thread_write_handler check for overflow
mei: make mei_write_message more readable
mei: check for error codes that mei_flow_ctrl_creds retuns
misc: at25: Parse dt settings
misc: hpilo: increase number of max supported channels
mei: mei.txt: minor grammar fixes
Merge tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg Kroah-Hartman:
"Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes
now settled down. All we have here is some extcon driver updates, w1
driver updates, a few printk cleanups that weren't needed for 3.5, but
are good to have now, and some other minor fixes/changes in the driver
core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <[email protected]>"
* tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
printk: Export struct log size and member offsets through vmcoreinfo
Drivers: hv: Change the hex constant to a decimal constant
driver core: don't trigger uevent after failure
extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device
sysfs: fail dentry revalidation after namespace change fix
sysfs: fail dentry revalidation after namespace change
extcon: spelling of detach in function doc
extcon: arizona: Stop microphone detection if we give up on it
extcon: arizona: Update cable reporting calls and split headset
PM / Runtime: Do not increment device usage counts before probing
kmsg - do not flush partial lines when the console is busy
kmsg - export "continuation record" flag to /dev/kmsg
kmsg - avoid warning for CONFIG_PRINTK=n compilations
kmsg - properly print over-long continuation lines
driver-core: Use kobj_to_dev instead of re-implementing it
driver-core: Move kobj_to_dev from genhd.h to device.h
driver core: Move deferred devices to the end of dpm_list before probing
driver core: move uevent call to driver_register
driver core: fix shutdown races with probe/remove(v3)
Extcon: Arizona: Add driver for Wolfson Arizona class devices
...
Merge tag 'staging-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree patches from Greg Kroah-Hartman:
"Here's the big staging tree merge for the 3.6-rc1 merge window.
There are some patches in here outside of drivers/staging/, notibly
the iio code (which is still stradeling the staging / not staging
boundry), the pstore code, and the tracing code. All of these have
gotten acks from the various subsystem maintainers to be included in
this tree. The pstore and tracing patches are related, and are coming
here as they replace one of the android staging drivers.
Otherwise, the normal staging mess. Lots of cleanups and a few new
drivers (some iio drivers, and the large csr wireless driver
abomination.)
Signed-off-by: Greg Kroah-Hartman <[email protected]>"
Fixed up trivial conflicts in drivers/staging/comedi/drivers/s626.h and
drivers/staging/gdm72xx/netlink_k.c
Merge tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and
drivers. There's some scsi changes that I think also went in through
the scsi tree, but they merge just fine. All of these patches have
been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <[email protected]>"
Fix up trivial conflicts in include/scsi/scsi_device.h (same libata
conflict that Jeff had already encountered)
* tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams
usb: Add quirk detection based on interface information
usb: s3c-hsotg: Add header file protection macros in s3c-hsotg.h
USB: ehci-s5p: Add vbus setup function to the s5p ehci glue layer
USB: add USB_VENDOR_AND_INTERFACE_INFO() macro
USB: notify phy when root hub port connect change
USB: remove 8 bytes of padding from usb_host_interface on 64 bit builds
USB: option: add ZTE MF821D
USB: sierra: QMI mode MC7710 moved to qcserial
USB: qcserial: adding Sierra Wireless devices
USB: qcserial: support generic Qualcomm serial ports
USB: qcserial: make probe more flexible
USB: qcserial: centralize probe exit path
USB: qcserial: consolidate usb_set_interface calls
USB: ehci-s5p: Add support for device tree
USB: ohci-exynos: Add support for device tree
USB: ehci-omap: fix compile failure(v1)
usb: host: tegra: pass correct pointer in ehci_setup()
USB: ehci-fsl: Update ifdef check to work on 64-bit ppc
USB: serial: keyspan: Removed unrequired parentheses.
...
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata updates from Jeff Garzik:
"Notable changes:
- Updating libata to directly bind with ACPI / runtime power mgmt.
This is a pre-req for SATA ZPODD (CD-ROM power management).
Touches ACPI (exports++) and SCSI in minor ways. Has been in
linux-next for weeks.
The rest of this should come via SCSI tree, as it involves a lot of
updates to the 'sr' driver etc.
Other, minor changes:
- module_pci_driver() removes a lot of common boilerplate from each
PCI driver
- minor coding style, whitespace cleanups
- pata_pcmcia bug fix, caught by Coccinelle
- pata_imx, sata_dwc_460ex minor vendor updates
- ahci_platform: use simple PM ops, and thereby add hibernation cb's
- Add a few device-specific quirks"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (23 commits)
[libata] pata_cmd64x: whitespace cleanup
libata-acpi: fix up for acpi_pm_device_sleep_state API
sata_dwc_460ex: device tree may specify dma_channel
ahci, trivial: fixed coding style issues related to braces
ahci_platform: add hibernation callbacks
libata-eh.c: local functions should not be exposed globally
libata-transport.c: local functions should not be exposed globally
sata_dwc_460ex: support hardreset
ata: use module_pci_driver
drivers/ata/pata_pcmcia.c: adjust suspicious bit operation
pata_imx: Convert to clk_prepare_enable/clk_disable_unprepare
ahci: Enable SB600 64bit DMA on MSI K9AGM2 (MS-7327) v2
[libata] Prevent interface errors with Seagate FreeAgent GoFlex
drivers/acpi/glue: revert accidental license-related 6b66d95895c bits
libata-acpi: add missing inlines in libata.h
libata: tell scsi layer device supports runtime power off
libata: detect Device Attention support
libata-acpi: register/unregister device to/from power resource
libata-acpi: add ata port runtime D3Cold support
libata-acpi: set acpi state for SATA port
...
ARM: mxs: fix compile error caused by prom_update_property change
The commit 475d009 (of: Improve prom_update_property() function)
changed prom_update_property interface, and causes the compile
error below.
CC arch/arm/mach-mxs/mach-mxs.o
arch/arm/mach-mxs/mach-mxs.c: In function ‘update_fec_mac_prop’:
arch/arm/mach-mxs/mach-mxs.c:216:4: error: too many arguments to function ‘prom_update_property’
include/linux/of.h:263:12: note: declared here
Update the caller update_fec_mac_prop to fix the error.
Kim, Milo [Fri, 20 Jul 2012 08:43:59 +0000 (16:43 +0800)]
leds: add new lp8788 led driver
TI LP8788 PMU has the current sink as the keyboard led driver.
The brightness is controlled by the i2c commands.
Configurable parameters can be defined in the platform side.
Patch v2.
(a) use workqueue on changing the brightness
(b) use mutex_lock/unlock when the brightness is set
and the led block of lp8788 device is enabled
(c) remove err_dev on _probe()
: just return as returned value if any errors
(d) replace module_init/exit() with module_platform_driver()
(e) add led configuration structure and loading them by default
if platform data is null
Dave Airlie [Thu, 26 Jul 2012 00:40:31 +0000 (10:40 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
Daniel writes: (this pull is the one with the bad patch dropped)
First pile of fixes for 3.6 already, and I'm afraid it's a bit larger than
what I'd wish for. But I've moved all the feature-y stuff to -next, so
this really is all -fixes. Most of it is handling fallout from the hw
context stuff, discovered now that mesa git has started using them for
real. Otherwise all just small fixes:
- unbreak modeset=0 on gen6+ (regressed in next)
- const mismatch fix for ->mode_fixup
- simplify overly clever lvds modeset code (current code can totally
confuse backlights, resulting in broken panels until a full power draw
restores them).
- fix some fallout from the flushing_list disabling (regression only
introduced in -next)
- DP link train improvements (this also kills the last 3.2 dp regression
afaik)
- bugfix for the new ddc VGA detection on newer platforms
- minor backlight fixes (one of them a -next regression)
- only enable the required PM interrupts (to avoid waking up the cpu
unnecessarily)
- some really minor bits (workaround clarification, make coverty happy,
hsw init fix)
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (23 commits)
drm/i915: unbreak lastclose for failed driver init
drm/i915: Set the context before setting up regs for the context.
drm/i915: constify mode in crtc_mode_fixup
drm/i915/lvds: ditch ->prepare special case
drm/i915: dereferencing an error pointer
drm/i915: fix invalid reference handling of the default ctx obj
drm/i915: Add -EIO to the list of known errors for __wait_seqno
drm/i915: Flush the context object from the CPU caches upon switching
drm/i915: Make the lock for pageflips interruptible
drm/i915: don't forget the PCH backlight registers
drm/i915: Insert a flush between batches if the breadcrumb was dropped
drm/i915: missing error case in init status page
drm/i915: mask tiled bit when updating ILK sprites
drm/i915: try to train DP even harder
drm/i915: kill intel_ddc_probe
drm/i915: check whether we actually received an edid in detect_ddc
drm/i915: fix up PCH backlight #define mixup
drm/i915: Add comments to explain the BSD tail write workaround
drm/i915: Disable the BLT on pre-production SNB hardware
drm/i915: initialize power wells in modeset_init_hw
...
Dave Airlie [Thu, 26 Jul 2012 00:35:44 +0000 (10:35 +1000)]
Merge branch 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: init vblank requests list
drm/nv50: extend vblank semaphore to generic dmaobj + offset pair
drm/nouveau: mark most of our ioctls as deprecated, move to compat layer
drm/nouveau: move current gpuobj code out of nouveau_object.c
drm/nouveau/gem: fix object reference leak in a failure path
drm/nv50: rename INVALID_QUERY_OR_TEXTURE error to INVALID_OPERATION
drm/nv84: decode PCRYPT errors
drm/nouveau: dcb table quirk for fdo#50830
nouveau: Fix alignment requirements on src and dst addresses
nouveau: Fix alignment requirements on src and dst addresses
Linear copy works by adding the offset to the buffer address,
which may end up not being 16-byte aligned.
Some tests I've written for prime_pcopy show that the engine
allows this correctly, so the restriction on lowest 4 bits of
address can be lifted safely.
The comments added were by envyas, I think because I used
a newer version.
Eric Dumazet [Wed, 25 Jul 2012 05:11:23 +0000 (05:11 +0000)]
ipv4: rt_cache_valid must check expired routes
commit d2d68ba9fe8 (ipv4: Cache input routes in fib_info nexthops.)
introduced rt_cache_valid() helper. It unfortunately doesn't check if
route is expired before caching it.
I noticed sk_setup_caps() was constantly called on a tcp workload.
Wei Yang [Wed, 25 Jul 2012 02:13:59 +0000 (02:13 +0000)]
net/pch_gpe: Cannot disable ethernet autonegation
When attempting to disable ethernet autonegation via ethtool,
the pch_gpe driver will set software reset bit of PHY chip, But
control register of PHY chip of FRI2 will reenable ethernet autonegation.
Commit efc73f4b "net: Fix memory leak - vlan_info struct" adds deletion of
VLAN 0 for devices with feature NETIF_F_HW_VLAN_FILTER. For driver
qeth these are the layer 3 devices. Usually there exists no
separate vlan net_device for VLAN 0. Thus the qeth functions
qeth_l3_free_vlan_addresses4() and qeth_l3_free_vlan_addresses6()
require an extra checking if function __vlan_find_dev_deep()
returns with a net_device.
Let the driver core handle device attribute creation and removal. This
will simplify the code and eliminates races between attribute
availability and userspace notification via uevents.
Currently the mlx4 drivers don't have the necessary callbacks to
implement EEH errors detection and recovery, so the PCI layer uses the
probe and remove callbacks to try to recover the device after an error on
the bus. However, these callbacks have race conditions with the internal
catastrophic error recovery functions, which will also detect the error
and this can cause the system to crash if both EEH and catas functions
try to reset the device.
This patch adds the necessary error recovery callbacks and makes sure
that the internal catastrophic error functions will not try to reset the
device in such scenarios. It also adds some calls to
pci_channel_offline() to suppress reads/writes on the bus when the slot
cannot accept I/O operations so we prevent unnecessary accesses to the
bus and speed up the device removal.
Chris Metcalf [Wed, 25 Jul 2012 19:49:23 +0000 (15:49 -0400)]
tilepro pci: fix pci_bus.subordinate bad bombing from b918c62e
The bombing to convert pci_bus.subordinate to busn_res.end accidentally
modified a "struct pci_dev" site, causing this file not to compile.
This commit reverts that code to use dev->subordinate again.
Chris Metcalf [Wed, 25 Jul 2012 19:40:50 +0000 (15:40 -0400)]
tilegx pci: fix semantic merge conflict with 3527ed81c
Yinghai Lu removed pci_bus.subordinate in pci-next, which meant that
the tile-next changes to add tilegx PCI support don't build. This
was expected (seen in linux-next) and this one-line fix is along
the same lines as commit b918c62e for all other architectures.
Alexander Block [Wed, 25 Jul 2012 21:19:24 +0000 (23:19 +0200)]
Btrfs: introduce BTRFS_IOC_SEND for btrfs send/receive
This patch introduces the BTRFS_IOC_SEND ioctl that is
required for send. It allows btrfs-progs to implement
full and incremental sends. Patches for btrfs-progs will
follow.
Alexander Block [Tue, 5 Jun 2012 19:07:48 +0000 (21:07 +0200)]
Btrfs: add btrfs_compare_trees function
This function is used to find the differences between
two trees. The tree compare skips whole subtrees if it
detects shared tree blocks and thus is pretty fast.
Alexander Block [Wed, 25 Jul 2012 15:35:53 +0000 (17:35 +0200)]
Btrfs: introduce subvol uuids and times
This patch introduces uuids for subvolumes. Each
subvolume has it's own uuid. In case it was snapshotted,
it also contains parent_uuid. In case it was received,
it also contains received_uuid.
It also introduces subvolume ctime/otime/stime/rtime. The
first two are comparable to the times found in inodes. otime
is the origin/creation time and ctime is the change time.
stime/rtime are only valid on received subvolumes.
stime is the time of the subvolume when it was
sent. rtime is the time of the subvolume when it was
received.
Additionally to the times, we have a transid for each
time. They are updated at the same place as the times.
btrfs receive uses stransid and rtransid to find out
if a received subvolume changed in the meantime.
If an older kernel mounts a filesystem with the
extented fields, all fields become invalid. The next
mount with a new kernel will detect this and reset the
fields.
Chris Mason [Wed, 25 Jul 2012 19:57:13 +0000 (15:57 -0400)]
Btrfs: call the ordered free operation without any locks held
Each ordered operation has a free callback, and this was called with the
worker spinlock held. Josef made the free callback also call iput,
which we can't do with the spinlock.
This drops the spinlock for the free operation and grabs it again before
moving through the rest of the list. We'll circle back around to this
and find a cleaner way that doesn't bounce the lock around so much.
Btrfs: Check INCOMPAT flags on remount and add helper function
In support of the recently added capability to remount with lzo
compression, provide a helper function to check the compression
INCOMPAT flags when remounting with lzo compression, and set
the flags if necessary.
Also, implement the new helper function when defragmenting with
explicit lzo compression and when setting the default subvolume.
Stephen Warren [Wed, 25 Jul 2012 20:02:44 +0000 (14:02 -0600)]
ARM: dt: tegra trimslice: add vbus-gpio property
On TrimSlice, Tegra's USB1 port may be routed to either an external micro
USB port, or an internal USB->SATA bridge for SSD or HDD. This muxing is
controlled by a GPIO. Whilst not strictly a VBUS GPIO, the TrimSlice
board files caused this GPIO to be set appropriately to enable the SATA
bridge by passing it as the VBUS GPIO to the USB driver. Echo this same
configuration in device tree to enable the SATA bridge.
An alternative might be to implement a full USB bus mux driver. However,
that seems over-complex right now.
libata-acpi: fix up for acpi_pm_device_sleep_state API
After merging the libata tree, today's [2012-07-01] linux-next build (x86_64
allmodconfig) failed like this:
drivers/ata/libata-acpi.c: In function 'ata_acpi_set_state':
drivers/ata/libata-acpi.c:872:5: error: too few arguments to function 'acpi_pm_device_sleep_state'
include/acpi/acpi_bus.h:418:5: note: declared here
Caused by commit 3bd46600a7a7 ("libata-acpi: add ata port runtime D3Cold
support") from the libata tree interacting with commit ee85f543710d
("ACPI/PM: specify lowest allowed state for device sleep state") from the
pci tree.
This patch adds ACPI_STATE_D3 as the new third parameter to
acpi_pm_device_sleep_state()
sata_dwc_460ex: device tree may specify dma_channel
Only channel 0 is currently support and the driver code is fixed on
channel 0. This patch lets device node specifying dma-channel in case
it is not 0. If no dma-channel property is specified, channel 0 is
used as default.
Jeff Layton [Wed, 25 Jul 2012 18:59:54 +0000 (14:59 -0400)]
cifs: ensure that we always do cifsFileInfo_get under the spinlock
The readpages bug is a regression that was introduced in 6993f74a5.
This also fixes a couple of similar bugs in the uncached read and write
codepaths.
Also, prevent this sort of thing in the future by having cifsFileInfo_get
take the spinlock itself, and adding a _locked variant for use in places
that are already holding the lock. The _put code has always done that
so this makes for a less confusing interface.
libata-transport.c: local functions should not be exposed globally
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol 'ata_is_port' was not declared. Should it be static?
warning: symbol 'ata_is_link' was not declared. Should it be static?
warning: symbol 'ata_is_ata_dev' was not declared. Should it be static?
The hardreset operation is currently not supported. This causes
sometime the SATA driver does cause kernel crash because of
none-determined state.a This patch will fix the issue.
Julia Lawall [Wed, 6 Jun 2012 21:41:40 +0000 (23:41 +0200)]
drivers/ata/pata_pcmcia.c: adjust suspicious bit operation
IO_DATA_PATH_WIDTH_8 is 0, so a bit-and with it is always false. The
value IO_DATA_PATH_WIDTH covers the bits of the IO_DATA_PATH constants, so
first pick those bits and then make the test using !=.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/).
In this case though we're enabling 64bit DMA for another MSI motherboard,
the K9AGM2 or MS-7327. It is new enough that all of the BIOS releases
since the initial release (1.0 from 2007-02-09) work correctly with 64bit
DMA enabled.
[libata] Prevent interface errors with Seagate FreeAgent GoFlex
When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.
Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.
Lin Ming [Mon, 2 Jul 2012 04:31:19 +0000 (12:31 +0800)]
libata-acpi: add missing inlines in libata.h
Adds inline for ata_acpi_unregister/ata_acpi_bind/ata_acpi_unbind
in drivers/ata/libata.h for !CONFIG_ATA_ACPI to fix below warnings.
warning: 'ata_acpi_unregister' defined but not used [-Wunused-function]
warning: 'ata_acpi_bind' defined but not used [-Wunused-function]
warning: 'ata_acpi_unbind' defined but not used [-Wunused-function]
Arne Jansen [Tue, 13 Sep 2011 09:18:10 +0000 (11:18 +0200)]
Btrfs: add helper for tree enumeration
Often no exact match is wanted but just the next lower or
higher item. There's a lot of duplicated code throughout
btrfs to deal with the corner cases. This patch adds a
helper function that can facilitate searching.
David Sterba [Mon, 1 Aug 2011 16:11:57 +0000 (18:11 +0200)]
btrfs: allow cross-subvolume file clone
Lift the EXDEV condition and allow different root trees for files being
cloned, then pass source inode's root when searching for extents.
Cloning is not allowed to cross vfsmounts, ie. when two subvolumes from
one filesystem are mounted separately.
Simon Baatz [Wed, 18 Jul 2012 22:04:09 +0000 (00:04 +0200)]
ARM: Orion: fix driver probe error handling with respect to clk
The clk patches added code to get and enable clocks in the
respective driver probe functions. If the probe function failed
for some reason after enabling the clock, the clock was not
disabled again in many cases.
Simon Baatz [Fri, 6 Jul 2012 18:42:38 +0000 (20:42 +0200)]
ARM: Kirkwood: Fix PHY disable clk problems
Commit 98d9986 (ARM: Kirkwood: Replace clock gating) and the fix 5fb2ce
(ARM: Kirkwood: clk_register_gate_fn: add fn assignment) introduced a custom
variant of clock gating which allows to define a function to be called
before gating the clock off.
This is used to disable the SATA and PCIe PHYs if the respective clocks
are unused after initialization.
However, of these two drivers, the SATA driver may be compiled as a module.
The driver re-enables the clocks at module init but the PHYs stay disabled.
Since the custom clock gating disabled the PHYs when gating the clock off,
it should also re-enable them when enabling the clock gate. This is done by
adding a second function that may be used to enable the PHYs.
Andrew Lunn [Thu, 19 Jul 2012 06:58:08 +0000 (08:58 +0200)]
ARM: Kirkwood: Ensure runit clock always ticks.
Marvell engineers tell us:
It seems that many units use the RUNIT clock.
SPI, UART, NAND, TWSI, ...
So it's not possible to clock gate it.
Currently the SPI, NAND and TWSI driver will clk_prepaure_enable()
this clk, but since we have no idea what ... is, and turning this clk
off results in a hard lock, unconditionally enable runit.
ARM: versatile: Don't use platform clock for Integrator & VE
Due to automatic merge of a613163dff04cbfcb7d66b06ef4a5f65498ee59b
"ARM: integrator: convert to common clock" and 56a34b03ff427046494db87f05fc810aaedd23a5 "ARM: versatile: Make
plat-versatile clock optional" two platforms: Integrator and
Versatile Express now select both COMMON_CLK and
PLAT_VERSATILE_CLOCK which breaks building them. Fixed now.
Which results in the drm core calling our lastclose function to clean
up the mess, but that one is neatly broken for such failure cases
since kms has been introduced in
Eric Anholt [Mon, 23 Jul 2012 19:33:55 +0000 (12:33 -0700)]
drm/i915: Set the context before setting up regs for the context.
Fixes failures in transform feedback on gen7 because our SOL_RESET
flag was setting the transform feedback offsets in the old context
(occasionally happened to be ours) instead of the new context.
Daniel Vetter [Wed, 11 Jul 2012 14:27:52 +0000 (16:27 +0200)]
drm/i915/lvds: ditch ->prepare special case
LVDS is the first output where dpms on/off and prepare/commit don't
perfectly match. Now the idea behind this special case seems to be
that for simple resolution changes on the LVDS we don't need to stop
the pipe, because (at least on newer chips) we can adjust the panel
fitter on the fly.
There are a few problems with the current code though:
- We still stop and restart the pipe unconditionally, because the crtc
helper code isn't flexible enough.
- We show some ugly flickering, especially when changing crtcs (this
the crtc helper would actually take into account, but we don't
implement the encoder->get_crtc callback required to make this work
properly).
So it doesn't even work as advertised. I agree that it would be nice
to do resolution changes on LVDS (and also eDP) whithout blacking the
screen where the panel fitter allows to do that. But imo we should
implement this as a special case a few layers up in the mode set code,
akin to how we already detect simple framebuffer changes (and only
update the required registers with ->mode_set_base).
Until this is all in place, make our lives easier and just rip it out.
Also note that this seems to fix actual bugs with enabling the lvds
output, see:
Chris Wilson [Sun, 15 Jul 2012 11:34:22 +0000 (12:34 +0100)]
drm/i915: Flush the context object from the CPU caches upon switching
The issue is that we stale data in the CPU caches, when we come to
swap-out the object, the CPU may short-circuit the reads from those
cacheline and so corrupt the context object.
Secondary, leaving the context object as being marked in the CPU write
domain whilst on the GPU active list is a bad idea and will throw
warnings later.
Note: Thanks to calling set_to_gtt_domain with write = false and not
setting any gpu write domain when putting a context object onto the
active list (when we switch away from it) the set_to_gtt_domain call
won't block.
Signed-off-by: Chris Wilson <[email protected]> Reviewed-by: Ben Widawsky <[email protected]>
[danvet: Added a note to the commit message and a comment in the code
to explain the clever non-blocking trick.] Signed-off-by: Daniel Vetter <[email protected]>
drm/radeon: on hotplug force link training to happen (v2)
To have DP behave like VGA/DVI we need to retrain the link
on hotplug. For this to happen we need to force link
training to happen by setting connector dpms to off
before asking it turning it on again.
v2: agd5f
- drop the dp_get_link_status() change in atombios_dp.c
for now. We still need the dpms OFF change.
drm/radeon: fix hotplug of DP to DVI|HDMI passive adapters (v2)
No need to retrain the link for passive adapters.
v2: agd5f
- no passive DP to VGA adapters, update comments
- assign radeon_connector_atom_dig after we are sure
we have a digital connector as analog connectors
have different private data.
- get new sink type before checking for retrain. No
need to check if it's no longer a DP connection.
We want to print link status query failed only if it's
an unexepected fail. If we query to see if we need
link training it might be because there is nothing
connected and thus link status query have the right
to fail in that case.
To avoid printing failure when it's expected, move the
failure message to proper place.
Ilija Hadzic [Tue, 15 May 2012 20:40:10 +0000 (16:40 -0400)]
drm: track dev_mapping in more robust and flexible way
Setting dev_mapping (pointer to the address_space structure
used for memory mappings) to the address_space of the first
opener's inode and then failing if other openers come in
through a different inode has a few restrictions that are
eliminated by this patch.
If we already have valid dev_mapping and we spot an opener
with different i_node, we force its i_mapping pointer to the
already established address_space structure (first opener's
inode). This will make all mappings from drm device hang off
the same address_space object.
Some benefits (things that now work and didn't work
before) of this patch are:
* user space can mknod and use any number of device
nodes and they will all work fine as long as the major
device number is that of the drm module.
* user space can even remove the first opener's device
nodes and mknod the new one and the applications and
windowing system will still work.
* GPU drivers can safely assume that dev->dev_mapping is
correct address_space and just blindly copy it
into their (private) bdev.dev_mapping
For reference, some discussion that lead to this patch can
be found here:
With commit 6503e5df08008b9a47022b5e9ebba658c8fa69af,
the value of /sys/class/thermal/thermal_zoneX/mode has been changed
from user/kernel to enabled/disabled.
Update the documentation so that users won't be confused.
Durgadoss R [Wed, 25 Jul 2012 02:10:58 +0000 (10:10 +0800)]
Thermal: Make Thermal trip points writeable
Some of the thermal drivers using the Generic Thermal Framework
require (all/some) trip points to be writeable. This patch makes
the trip point temperatures writeable on a per-trip point basis,
and modifies the required function call in thermal.c. This patch
also updates the Documentation to reflect the new change.
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <[email protected]>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw:
GFS2: Eliminate 64-bit divides
GFS2: Reduce file fragmentation
GFS2: kernel panic with small gfs2 filesystems - 1 RG
GFS2: Fixing double brelse'ing bh allocated in gfs2_meta_read when EIO occurs
GFS2: Combine functions get_local_rgrp and gfs2_inplace_reserve
GFS2: Add kobject release method
GFS2: Size seq_file buffer more carefully
GFS2: Use seq_vprintf for glocks debugfs file
seq_file: Add seq_vprintf function and export it
GFS2: Use lvbs for storing rgrp information with mount option
GFS2: Cache last hash bucket for glock seq_files
GFS2: Increase buffer size for glocks and glstats debugfs files
GFS2: Fix error handling when reading an invalid block from the journal
GFS2: Add "top dir" flag support
GFS2: Fold quota data into the reservations struct
GFS2: Extend the life of the reservations
Merge branch 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue changes from Tejun Heo:
"There are three major changes.
- WQ_HIGHPRI has been reimplemented so that high priority work items
are served by worker threads with -20 nice value from dedicated
highpri worker pools.
- CPU hotplug support has been reimplemented such that idle workers
are kept across CPU hotplug events. This makes CPU hotplug cheaper
(for PM) and makes the code simpler.
- flush_kthread_work() has been reimplemented so that a work item can
be freed while executing. This removes an annoying behavior
difference between kthread_worker and workqueue."
* 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix spurious CPU locality WARN from process_one_work()
kthread_worker: reimplement flush_kthread_work() to allow freeing the work item being executed
kthread_worker: reorganize to prepare for flush_kthread_work() reimplementation
workqueue: simplify CPU hotplug code
workqueue: remove CPU offline trustee
workqueue: don't butcher idle workers on an offline CPU
workqueue: reimplement CPU online rebinding to handle idle workers
workqueue: drop @bind from create_worker()
workqueue: use mutex for global_cwq manager exclusion
workqueue: ROGUE workers are UNBOUND workers
workqueue: drop CPU_DYING notifier operation
workqueue: perform cpu down operations from low priority cpu_notifier()
workqueue: reimplement WQ_HIGHPRI using a separate worker_pool
workqueue: introduce NR_WORKER_POOLS and for_each_worker_pool()
workqueue: separate out worker_pool flags
workqueue: use @pool instead of @gcwq or @cpu where applicable
workqueue: factor out worker_pool from global_cwq
workqueue: don't use WQ_HIGHPRI for unbound workqueues
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull misc udf, ext2, ext3, and isofs fixes from Jan Kara:
"Assorted, mostly trivial, fixes for udf, ext2, ext3, and isofs. I'm
on vacation and scarcely checking email since we are expecting baby
any day now but these fixes should be safe to go in and I don't want
to delay them unnecessarily."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: avoid info leak on export
isofs: avoid info leak on export
udf: Improve table length check to avoid possible overflow
ext3: Check return value of blkdev_issue_flush()
jbd: Check return value of blkdev_issue_flush()
udf: Do not decrement i_blocks when freeing indirect extent block
udf: Fix memory leak when mounting
ext2: cleanup the confused goto label
UDF: Remove unnecessary variable "offset" from udf_fill_inode
udf: stop using s_dirt
ext3: force ro mount if ext3_setup_super() fails
quota: fix checkpatch.pl warning by replacing <asm/uaccess.h> with <linux/uaccess.h>
projects / linux.git / log