Jim Mattson [Tue, 15 Oct 2019 17:44:05 +0000 (10:44 -0700)]
KVM: nVMX: Don't leak L1 MMIO regions to L2
If the "virtualize APIC accesses" VM-execution control is set in the
VMCS, the APIC virtualization hardware is triggered when a page walk
in VMX non-root mode terminates at a PTE wherein the address of the 4k
page frame matches the APIC-access address specified in the VMCS. On
hardware, the APIC-access address may be any valid 4k-aligned physical
address.
KVM's nVMX implementation enforces the additional constraint that the
APIC-access address specified in the vmcs12 must be backed by
a "struct page" in L1. If not, L0 will simply clear the "virtualize
APIC accesses" VM-execution control in the vmcs02.
The problem with this approach is that the L1 guest has arranged the
vmcs12 EPT tables--or shadow page tables, if the "enable EPT"
VM-execution control is clear in the vmcs12--so that the L2 guest
physical address(es)--or L2 guest linear address(es)--that reference
the L2 APIC map to the APIC-access address specified in the
vmcs12. Without the "virtualize APIC accesses" VM-execution control in
the vmcs02, the APIC accesses in the L2 guest will directly access the
APIC-access page in L1.
When there is no mapping whatsoever for the APIC-access address in L1,
the L2 VM just loses the intended APIC virtualization. However, when
the APIC-access address is mapped to an MMIO region in L1, the L2
guest gets direct access to the L1 MMIO device. For example, if the
APIC-access address specified in the vmcs12 is 0xfee00000, then L2
gets direct access to L1's APIC.
Since this vmcs12 configuration is something that KVM cannot
faithfully emulate, the appropriate response is to exit to userspace
with KVM_INTERNAL_ERROR_EMULATION.
Miaohe Lin [Fri, 18 Oct 2019 02:50:31 +0000 (10:50 +0800)]
KVM: SVM: Fix potential wrong physical id in avic_handle_ldr_update
Guest physical APIC ID may not equal to vcpu->vcpu_id in some case.
We may set the wrong physical id in avic_handle_ldr_update as we
always use vcpu->vcpu_id. Get physical APIC ID from vAPIC page
instead.
Export and use kvm_xapic_id here and in avic_handle_apic_id_update
as suggested by Vitaly.
Sudeep Holla [Fri, 18 Oct 2019 10:58:15 +0000 (11:58 +0100)]
cpufreq: Cancel policy update work scheduled before freeing
Scheduled policy update work may end up racing with the freeing of the
policy and unregistering the driver.
One possible race is as below, where the cpufreq_driver is unregistered,
but the scheduled work gets executed at later stage when, cpufreq_driver
is NULL (i.e. after freeing the policy and driver).
Unable to handle kernel NULL pointer dereference at virtual address 0000001c
pgd = (ptrval)
[0000001c] *pgd=80000080204003, *pmd=00000000
Internal error: Oops: 206 [#1] SMP THUMB2
Modules linked in:
CPU: 0 PID: 34 Comm: kworker/0:1 Not tainted 5.4.0-rc3-00006-g67f5a8081a4b #86
Hardware name: ARM-Versatile Express
Workqueue: events handle_update
PC is at cpufreq_set_policy+0x58/0x228
LR is at dev_pm_qos_read_value+0x77/0xac
Control: 70c5387d Table: 80203000 DAC: fffffffd
Process kworker/0:1 (pid: 34, stack limit = 0x(ptrval))
(cpufreq_set_policy) from (refresh_frequency_limits.part.24+0x37/0x48)
(refresh_frequency_limits.part.24) from (handle_update+0x2f/0x38)
(handle_update) from (process_one_work+0x16d/0x3cc)
(process_one_work) from (worker_thread+0xff/0x414)
(worker_thread) from (kthread+0xff/0x100)
(kthread) from (ret_from_fork+0x11/0x28)
Fixes: 67d874c3b2c6 ("cpufreq: Register notifiers with the PM QoS framework") Signed-off-by: Sudeep Holla <[email protected]>
[ rjw: Cancel the work before dropping the QoS requests ] Acked-by: Viresh Kumar <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
Gerald Schaefer [Mon, 21 Oct 2019 17:56:00 +0000 (19:56 +0200)]
s390/kaslr: add support for R_390_GLOB_DAT relocation type
Commit "bpf: Process in-kernel BTF" in linux-next introduced an undefined
__weak symbol, which results in an R_390_GLOB_DAT relocation type. That
is not yet handled by the KASLR relocation code, and the kernel stops with
the message "Unknown relocation type".
Add code to detect and handle R_390_GLOB_DAT relocation types and undefined
symbols.
Johan Hovold [Thu, 10 Oct 2019 13:13:33 +0000 (15:13 +0200)]
s390/zcrypt: fix memleak at release
If a process is interrupted while accessing the crypto device and the
global ap_perms_mutex is contented, release() could return early and
fail to free related resources.
Takashi Iwai [Tue, 22 Oct 2019 15:45:14 +0000 (17:45 +0200)]
ALSA: usb-audio: Fix copy&paste error in the validator
The recently introduced USB-audio descriptor validator had a stupid
copy&paste error that may lead to an unexpected overlook of too short
descriptors for processing and extension units. It's likely the cause
of the report triggered by syzkaller fuzzer. Let's fix it.
allows CAP_EXCLUSIVE events to be grouped with other events. Since all
of those also happen to be AUX events (which is not the case the other
way around, because arch/s390), this changes the rules for stopping the
output: the AUX event may not be on its PMU's context any more, if it's
grouped with a HW event, in which case it will be on that HW event's
context instead. If that's the case, munmap() of the AUX buffer can't
find and stop the AUX event, potentially leaving the last reference with
the atomic context, which will then end up freeing the AUX buffer. This
will then trip warnings:
Fix this by using the context's PMU context when looking for events
to stop, instead of the event's PMU context.
Paolo Bonzini [Tue, 22 Oct 2019 11:31:29 +0000 (13:31 +0200)]
Merge tag 'kvmarm-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm fixes for 5.4, take #2
Special PMU edition:
- Fix cycle counter truncation
- Fix cycle counter overflow limit on pure 64bit system
- Allow chained events to be actually functional
- Correct sample period after overflow
KVM: VMX: Remove specialized handling of unexpected exit-reasons
Commit bf653b78f960 ("KVM: vmx: Introduce handle_unexpected_vmexit
and handle WAITPKG vmexit") introduced specialized handling of
specific exit-reasons that should not be raised by CPU because
KVM configures VMCS such that they should never be raised.
However, since commit 7396d337cfad ("KVM: x86: Return to userspace
with internal error on unexpected exit reason"), VMX & SVM
exit handlers were modified to generically handle all unexpected
exit-reasons by returning to userspace with internal error.
Therefore, there is no need for specialized handling of specific
unexpected exit-reasons (This specialized handling also introduced
inconsistency for these exit-reasons to silently skip guest instruction
instead of return to userspace on internal-error).
Fixes: bf653b78f960 ("KVM: vmx: Introduce handle_unexpected_vmexit and handle WAITPKG vmexit") Signed-off-by: Liran Alon <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
selftests: kvm: fix sync_regs_test with newer gccs
Commit 204c91eff798a ("KVM: selftests: do not blindly clobber registers in
guest asm") was intended to make test more gcc-proof, however, the result
is exactly the opposite: on newer gccs (e.g. 8.2.1) the test breaks with
==== Test Assertion Failure ====
x86_64/sync_regs_test.c:168: run->s.regs.regs.rbx == 0xBAD1DEA + 1
pid=14170 tid=14170 - Invalid argument
1 0x00000000004015b3: main at sync_regs_test.c:166 (discriminator 6)
2 0x00007f413fb66412: ?? ??:0
3 0x000000000040191d: _start at ??:?
rbx sync regs value incorrect 0x1.
Apparently, compile is still free to play games with registers even
when they have variables attached.
Re-write guest code with 'asm volatile' by embedding ucall there and
making sure rbx is preserved.
Fixes: 204c91eff798a ("KVM: selftests: do not blindly clobber registers in guest asm") Signed-off-by: Vitaly Kuznetsov <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
selftests: kvm: vmx_set_nested_state_test: don't check for VMX support twice
vmx_set_nested_state_test() checks if VMX is supported twice: in the very
beginning (and skips the whole test if it's not) and before doing
test_vmx_nested_state(). One should be enough.
Linus Torvalds [Tue, 22 Oct 2019 10:40:07 +0000 (06:40 -0400)]
Merge tag 'pinctrl-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a bunch of pin control fixes. I was lagging behind on this
one, some fixes should have come in earlier, sorry about that.
Anyways here it is, pretty straight-forward fixes, the Strago fix
stand out as something serious affecting a lot of machines.
Summary:
- Handle multiple instances of Intel chips without complaining.
- Restore the Intel Strago DMI workaround
- Make the Armada 37xx handle pins over 32
- Fix the polarity of the LED group on Armada 37xx
- Fix an off-by-one bug in the NS2 driver
- Fix error path for iproc's platform_get_irq()
- Fix error path on the STMFX driver
- Fix a typo in the Berlin AS370 driver
- Fix up misc errors in the Aspeed 2600 BMC support
- Fix a stray SPDX tag"
* tag 'pinctrl-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: aspeed-g6: Rename SD3 to EMMC and rework pin groups
pinctrl: aspeed-g6: Fix UART13 group pinmux
pinctrl: aspeed-g6: Make SIG_DESC_CLEAR() behave intuitively
pinctrl: aspeed-g6: Fix I3C3/I3C4 pinmux configuration
pinctrl: aspeed-g6: Fix I2C14 SDA description
pinctrl: aspeed-g6: Sort pins for sanity
dt-bindings: pinctrl: aspeed-g6: Rework SD3 function and groups
pinctrl: berlin: as370: fix a typo s/spififib/spdifib
pinctrl: armada-37xx: swap polarity on LED group
pinctrl: stmfx: fix null pointer on remove
pinctrl: iproc: allow for error from platform_get_irq()
pinctrl: ns2: Fix off by one bugs in ns2_pinmux_enable()
pinctrl: bcm-iproc: Use SPDX header
pinctrl: armada-37xx: fix control of pins 32 and up
pinctrl: cherryview: restore Strago DMI workaround for all versions
pinctrl: intel: Allocate IRQ chip dynamic
Zhenzhong Duan [Fri, 18 Oct 2019 00:49:29 +0000 (08:49 +0800)]
cpuidle: haltpoll: Take 'idle=' override into account
Currenly haltpoll isn't aware of the 'idle=' override, the priority is
'idle=poll' > haltpoll > 'idle=halt'. When 'idle=poll' is used, cpuidle
driver is bypassed but current_driver in sys still shows 'haltpoll'.
When 'idle=halt' is used, haltpoll takes precedence and makes
'idle=halt' have no effect.
Add a check to prevent the haltpoll driver from loading if 'idle=' is
present.
Any subsequent call to perf_trace_event_reg() will observe total_ref_count > 0,
causing the perf_trace_buf to be always NULL. This can result in perf_trace_buf
getting accessed from perf_trace_buf_alloc() without being initialized. Acquiring
event_mutex in perf_kprobe_init() before calling perf_trace_event_init() should
fix this race.
The race caused the following bug:
Unable to handle kernel paging request at virtual address 0000003106f2003c
Mem abort info:
ESR = 0x96000045
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000045
CM = 0, WnR = 1
user pgtable: 4k pages, 39-bit VAs, pgdp = ffffffc034b9b000
[0000003106f2003c] pgd=0000000000000000, pud=0000000000000000
Internal error: Oops: 96000045 [#1] PREEMPT SMP
Process syz-executor (pid: 18393, stack limit = 0xffffffc093190000)
pstate: 80400005 (Nzcv daif +PAN -UAO)
pc : __memset+0x20/0x1ac
lr : memset+0x3c/0x50
sp : ffffffc09319fc50
Ingo Molnar [Mon, 21 Oct 2019 23:15:45 +0000 (01:15 +0200)]
Merge tag 'perf-core-for-mingo-5.5-20191021' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
perf trace:
- Add syscall failure stats to -s/--summary and -S/--with-summary, works in
combination with specifying just a set of syscalls, see below first with
-s/--summary, then with -S/--with-summary just for the syscalls we saw failing
with -s:
- Add a generator for x86's IRQ vectors -> strings
- Introduce stroul() (string -> number) methods for the strarray and
strarrays classes, also strtoul_flags, allowing to go from both strings
and or-ed strings to numbers, allowing things like:
- Fix objdump --no-show-raw-insn flag to work with goth gcc and clang.
- Streamline objdump execution, preserving the right error codes for better
reporting to user.
perf report:
- Add warning when libunwind not compiled in.
perf stat:
Jin Yao:
- Support --all-kernel/--all-user, to match options available in 'perf record',
asking that all the events specified work just with kernel or user events.
perf list:
Jin Yao:
- Hide deprecated events by default, allow showing them with --deprecated.
libbperf:
Jiri Olsa:
- Allow to build with -ltcmalloc.
- Finish mmap interface, getting more stuff from tools/perf while adding
abstractions to avoid pulling too much stuff, to get libperf to grow as
tools needs things like auxtrace, etc.
perf scripting engines:
Steven Rostedt (VMware):
- Iterate on tep event arrays directly, fixing script generation with
'-g python' when having multiple tracepoints in a perf.data file.
core:
- Allow to build with -ltcmalloc.
perf test:
Leo Yan:
- Report failure for mmap events.
- Avoid infinite loop for task exit case.
- Remove needless headers for bp_account test.
- Add dedicated checking helper is_supported().
- Disable bp_signal testing for arm64.
Vendor events:
arm64:
John Garry:
- Fix Hisi hip08 DDRC PMU eventname.
- Add some missing events for Hisi hip08 DDRC, L3C and HHA PMUs.
The platform detection VMWARE_PORT macro uses the VMWARE_HYPERVISOR_PORT
definition, but expects it to be an integer. However, when it was moved
to the new vmware.h include file, it was changed to be a string to better
fit into the VMWARE_HYPERCALL set of macros. This obviously breaks the
platform detection VMWARE_PORT functionality.
Change the VMWARE_HYPERVISOR_PORT and VMWARE_HYPERVISOR_PORT_HB
definitions to be integers, and use __stringify() for their stringified
form when needed.
Olof Johansson [Mon, 21 Oct 2019 19:07:35 +0000 (12:07 -0700)]
Merge tag 'davinci-fixes-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
DaVinci fixes for v5.4
======================
* fix GPIO backlight support on DA850 by enabling the needed config
in davinci_all_defconfig. This is a fix because the driver and board
support got converted to use BACKLIGHT_GPIO driver, but defconfig update
is still missing in v5.4.
* fix for McBSP DMA on DM365
* tag 'davinci-fixes-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
Olof Johansson [Mon, 21 Oct 2019 19:07:27 +0000 (12:07 -0700)]
Merge tag 'v5.4-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
A number of fixes for individual boards like the rockpro64, and Hugsun X99
as well as a fix for the Gru-Kevin display override and fixing the dt-
binding for Theobroma boards to the correct naming that is also actually
used in the wild.
Olof Johansson [Mon, 21 Oct 2019 19:07:13 +0000 (12:07 -0700)]
Merge tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4:
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
* tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Olof Johansson [Mon, 21 Oct 2019 19:06:46 +0000 (12:06 -0700)]
Merge tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
More fixes for omap variants:
- Update more panel options in omap2plus_defconfig that got changed
as we moved to use generic LCD panels
- Remove unused twl_keypad for logicpd-torpedo-som to avoid boot
time warnings. This is only a cosmetic fix, but at least dmesg output
is now getting more readable after all the fixes to remove pointless
warnings
- Fix gpu_cm node name as we still have a non-standard node name
dependency for clocks. This should eventually get fixed by use
of domain specific compatible property
- Fix use of i2c-mux-idle-disconnect for m3874-iceboard
- Use level interrupt for omap4 & 5 wlcore to avoid lost edge
interrupts
* tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Use level interrupt for omap4 & 5 wlcore
ARM: dts: am3874-iceboard: Fix 'i2c-mux-idle-disconnect' usage
ARM: dts: omap5: fix gpu_cm clock provider name
ARM: dts: logicpd-torpedo-som: Remove twl_keypad
ARM: omap2plus_defconfig: Fix selected panels after generic panel changes
afzal mohammed [Mon, 21 Oct 2019 05:06:14 +0000 (06:06 +0100)]
ARM: 8926/1: v7m: remove register save to stack before svc
r0-r3 & r12 registers are saved & restored, before & after svc
respectively. Intention was to preserve those registers across thread to
handler mode switch.
On v7-M, hardware saves the register context upon exception in AAPCS
complaint way. Restoring r0-r3 & r12 is done from stack location where
hardware saves it, not from the location on stack where these registers
were saved.
To clarify, on stm32f429 discovery board:
1. before svc, sp - 0x90009ff8
2. r0-r3,r12 saved to 0x90009ff8 - 0x9000a00b
3. upon svc, h/w decrements sp by 32 & pushes registers onto stack
4. after svc, sp - 0x90009fd8
5. r0-r3,r12 restored from 0x90009fd8 - 0x90009feb
Above means r0-r3,r12 is not restored from the location where they are
saved, but since hardware pushes the registers onto stack, the registers
are restored correctly.
Note that during register saving to stack (step 2), it goes past
0x9000a000. And it seems, based on objdump, there are global symbols
residing there, and it perhaps can cause issues on a non-XIP Kernel
(on XIP, data section is setup later).
Based on the analysis above, manually saving registers onto stack is at
best no-op and at worst can cause data section corruption. Hence remove
storing of registers onto stack before svc.
Fixes: b70cd406d7fe ("ARM: 8671/1: V7M: Preserve registers across switch from Thread to Handler mode") Signed-off-by: afzal mohammed <[email protected]> Acked-by: Vladimir Murzin <[email protected]> Signed-off-by: Russell King <[email protected]>
For Sitronix st1633 multi-touch controller driver the coordinates reported
for multiple fingers were wrong, as it was always taking LSB of coordinates
from the first contact data.
Sascha Hauer [Fri, 18 Oct 2019 09:39:34 +0000 (11:39 +0200)]
mmc: mxs: fix flags passed to dmaengine_prep_slave_sg
Since ceeeb99cd821 we no longer abuse the DMA_CTRL_ACK flag for custom
driver use and introduced the MXS_DMA_CTRL_WAIT4END instead. We have not
changed all users to this flag though. This patch fixes it for the
mxs-mmc driver.
Mihail Atanassov [Thu, 10 Oct 2019 10:30:07 +0000 (10:30 +0000)]
drm/komeda: Don't flush inactive pipes
HW doesn't allow flushing inactive pipes and raises an MERR interrupt
if you try to do so. Stop triggering the MERR interrupt in the
middle of a commit by calling drm_atomic_helper_commit_planes
with the ACTIVE_ONLY flag.
In case of master pending state, it should not trigger a master
command, otherwise data could be corrupted because this H/W shares
the same data buffer for slave and master operations. It also means
that H/W command queue handling is unreliable because of the buffer
sharing issue. To fix this issue, it clears command queue if a
master command is queued in pending state to use S/W solution
instead of H/W command queue handling. Also, it refines restarting
mechanism of the pending master command.
Takashi Iwai [Mon, 21 Oct 2019 12:05:26 +0000 (14:05 +0200)]
Merge tag 'asoc-fix-v5.4-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.4
A collection of fixes that have arrived since the merge window. There
are a small number of core fixes here but they are smaller ones around
error handling.
Faiz Abbas [Thu, 10 Oct 2019 10:52:30 +0000 (16:22 +0530)]
mmc: sdhci-omap: Fix Tuning procedure for temperatures < -20C
According to the App note[1] detailing the tuning algorithm, for
temperatures < -20C, the initial tuning value should be min(largest value
in LPW - 24, ceil(13/16 ratio of LPW)). The largest value in LPW is
(max_window + 4 * (max_len - 1)) and not (max_window + 4 * max_len) itself.
Fix this implementation.
Thomas Richter [Mon, 21 Oct 2019 08:33:54 +0000 (10:33 +0200)]
perf/aux: Fix tracking of auxiliary trace buffer allocation
The following commit from the v5.4 merge window:
d44248a41337 ("perf/core: Rework memory accounting in perf_mmap()")
... breaks auxiliary trace buffer tracking.
If I run command 'perf record -e rbd000' to record samples and saving
them in the **auxiliary** trace buffer then the value of 'locked_vm' becomes
negative after all trace buffers have been allocated and released:
The value of user->locked_vm increases to a limit then the memory
is tracked by pinned_vm.
During deallocation the size is subtracted from pinned_vm until
it hits a limit. Then a larger value is subtracted from locked_vm
leading to a large number (because of type unsigned):
This value sticks for the user until system is rebooted, causing
follow-on system calls using locked_vm resource limit to fail.
Note: There is no issue using the normal trace buffer.
In fact the issue is in perf_mmap_close(). During allocation auxiliary
trace buffer memory is either traced as 'extra' and added to 'pinned_vm'
or trace as 'user_extra' and added to 'locked_vm'. This applies for
normal trace buffers and auxiliary trace buffer.
However in function perf_mmap_close() all auxiliary trace buffer is
subtraced from 'locked_vm' and never from 'pinned_vm'. This breaks the
ballance.
Marek Szyprowski [Thu, 17 Oct 2019 10:27:58 +0000 (12:27 +0200)]
opp: core: Revert "add regulators enable and disable"
All the drivers, which use the OPP framework control regulators, which
are already enabled. Typically those regulators are also system critical,
due to providing power to CPU core or system buses. It turned out that
there are cases, where calling regulator_enable() on such boot-enabled
regulator has side-effects and might change its initial voltage due to
performing initial voltage balancing without all restrictions from the
consumers. Until this issue becomes finally solved in regulator core,
avoid calling regulator_enable()/disable() from the OPP framework.
According to MS-CIFS specification MID 0xFFFF should not be used by the
CIFS client, but we actually do. Besides, this has proven to cause races
leading to oops between SendReceive2/cifs_demultiplex_thread. On SMB1,
MID is a 2 byte value easy to reach in CurrentMid which may conflict with
an oplock break notification request coming from server
Steve French [Sat, 12 Oct 2019 00:36:13 +0000 (17:36 -0700)]
cifs: clarify comment about timestamp granularity for old servers
It could be confusing why we set granularity to 1 seconds rather
than 2 seconds (1 second is the max the VFS allows) for these
mounts to very old servers ...
cifs: Handle -EINPROGRESS only when noblockcnt is set
We only want to avoid blocking in connect when mounting SMB root
filesystems, otherwise bail out from generic_ip_connect() so cifs.ko
can perform any reconnect failover appropriately.
This fixes DFS failover/reconnection tests in upstream buildbot.
Fixes: 8eecd1c2e5bc ("cifs: Add support for root file systems") Signed-off-by: Paulo Alcantara (SUSE) <[email protected]> Signed-off-by: Steve French <[email protected]>
PM: QoS: Drop frequency QoS types from device PM QoS
There are no more active users of DEV_PM_QOS_MIN_FREQUENCY and
DEV_PM_QOS_MAX_FREQUENCY device PM QoS request types, so drop them
along with the code supporting them.
Replace the CPU device PM QoS used for the management of min and max
frequency constraints in cpufreq (and its users) with per-policy
frequency QoS to avoid problems with cpufreq policies covering
more then one CPU.
Namely, a cpufreq driver is registered with the subsys interface
which calls cpufreq_add_dev() for each CPU, starting from CPU0, so
currently the PM QoS notifiers are added to the first CPU in the
policy (i.e. CPU0 in the majority of cases).
In turn, when the cpufreq driver is unregistered, the subsys interface
doing that calls cpufreq_remove_dev() for each CPU, starting from CPU0,
and the PM QoS notifiers are only removed when cpufreq_remove_dev() is
called for the last CPU in the policy, say CPUx, which as a rule is
not CPU0 if the policy covers more than one CPU. Then, the PM QoS
notifiers cannot be removed, because CPUx does not have them, and
they are still there in the device PM QoS notifiers list of CPU0,
which prevents new PM QoS notifiers from being registered for CPU0
on the next attempt to register the cpufreq driver.
The same issue occurs when the first CPU in the policy goes offline
before unregistering the driver.
After this change it does not matter which CPU is the policy CPU at
the driver registration time and whether or not it is online all the
time, because the frequency QoS is per policy and not per CPU.
Introduce frequency QoS, based on the "raw" low-level PM QoS, to
represent min and max frequency requests and aggregate constraints.
The min and max frequency requests are to be represented by
struct freq_qos_request objects and the aggregate constraints are to
be represented by struct freq_constraints objects. The latter are
expected to be initialized with the help of freq_constraints_init().
The freq_qos_read_value() helper is defined to retrieve the aggregate
constraints values from a given struct freq_constraints object and
there are the freq_qos_add_request(), freq_qos_update_request() and
freq_qos_remove_request() helpers to manipulate the min and max
frequency requests. It is assumed that the the helpers will not
run concurrently with each other for the same struct freq_qos_request
object, so if that may be the case, their uses must ensure proper
synchronization between them (e.g. through locking).
In addition, freq_qos_add_notifier() and freq_qos_remove_notifier()
are provided to add and remove notifiers that will trigger on aggregate
constraint changes to and from a given struct freq_constraints object,
respectively.
Linus Torvalds [Sun, 20 Oct 2019 16:36:57 +0000 (12:36 -0400)]
Merge tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild fixes from Masahiro Yamada:
- fix a bashism of setlocalversion
- do not use the too new --sort option of tar
* tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kheaders: substituting --sort in archive creation
scripts: setlocalversion: fix a bashism
kbuild: update comment about KBUILD_ALLDIRS
Linus Torvalds [Sun, 20 Oct 2019 10:31:14 +0000 (06:31 -0400)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- Prevent a NULL pointer dereference in the X2APIC code in case of a
CPU hotplug failure.
- Prevent boot failures on HP superdome machines by invalidating the
level2 kernel pagetable entries outside of the kernel area as
invalid so BIOS reserved space won't be touched unintentionally.
Also ensure that memory holes are rounded up to the next PMD
boundary correctly.
- Enable X2APIC support on Hyper-V to prevent boot failures.
- Set the paravirt name when running on Hyper-V for consistency
- Move a function under the appropriate ifdef guard to prevent build
warnings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/acpi: Move get_cmdline_acpi_rsdp() under #ifdef guard
x86/hyperv: Set pv_info.name to "Hyper-V"
x86/apic/x2apic: Fix a NULL pointer deref when handling a dying cpu
x86/hyperv: Make vapic support x2apic mode
x86/boot/64: Round memory hole size up to next PMD page
x86/boot/64: Make level2_kernel_pgt pages invalid outside kernel area
Linus Torvalds [Sun, 20 Oct 2019 10:27:54 +0000 (06:27 -0400)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A small set of irq chip driver fixes and updates:
- Update the SIFIVE PLIC interrupt driver to use the fasteoi handler
to address the shortcomings of the existing flow handling which was
prone to lose interrupts
- Use the proper limit for GIC interrupt line numbers
- Add retrigger support for the recently merged Anapurna Labs Fabric
interrupt controller to make it complete
- Enable the ATMEL AIC5 interrupt controller driver on the new
SAM9X60 SoC"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Switch to fasteoi flow
irqchip/gic-v3: Fix GIC_LINE_NR accessor
irqchip/atmel-aic5: Add support for sam9x60 irqchip
irqchip/al-fic: Add support for irq retrigger
Linus Torvalds [Sun, 20 Oct 2019 10:25:12 +0000 (06:25 -0400)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull hrtimer fixlet from Thomas Gleixner:
"A single commit annotating the lockcless access to timer->base with
READ_ONCE() and adding the WRITE_ONCE() counterparts for completeness"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Annotate lockless access to timer->base
Marc Zyngier [Sun, 6 Oct 2019 09:28:50 +0000 (10:28 +0100)]
KVM: arm64: pmu: Reset sample period on overflow handling
The PMU emulation code uses the perf event sample period to trigger
the overflow detection. This works fine for the *first* overflow
handling, but results in a huge number of interrupts on the host,
unrelated to the number of interrupts handled in the guest (a x20
factor is pretty common for the cycle counter). On a slow system
(such as a SW model), this can result in the guest only making
forward progress at a glacial pace.
It turns out that the clue is in the name. The sample period is
exactly that: a period. And once the an overflow has occured,
the following period should be the full width of the associated
counter, instead of whatever the guest had initially programed.
Reset the sample period to the architected value in the overflow
handler, which now results in a number of host interrupts that is
much closer to the number of interrupts in the guest.
Fixes: b02386eb7dac ("arm64: KVM: Add PMU overflow interrupt routing") Reviewed-by: Andrew Murray <[email protected]> Signed-off-by: Marc Zyngier <[email protected]>
Marc Zyngier [Thu, 3 Oct 2019 17:02:08 +0000 (18:02 +0100)]
KVM: arm64: pmu: Fix cycle counter truncation
When a counter is disabled, its value is sampled before the event
is being disabled, and the value written back in the shadow register.
In that process, the value gets truncated to 32bit, which is adequate
for any counter but the cycle counter (defined as a 64bit counter).
This obviously results in a corrupted counter, and things like
"perf record -e cycles" not working at all when run in a guest...
A similar, but less critical bug exists in kvm_pmu_get_counter_value.
Make the truncation conditional on the counter not being the cycle
counter, which results in a minor code reorganisation.
Fixes: 80f393a23be6 ("KVM: arm/arm64: Support chained PMU counters") Reviewed-by: Andrew Murray <[email protected]> Reported-by: Julien Thierry <[email protected]> Signed-off-by: Marc Zyngier <[email protected]>
Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
Eric Dumazet [Fri, 18 Oct 2019 22:20:05 +0000 (15:20 -0700)]
net: reorder 'struct net' fields to avoid false sharing
Intel test robot reported a ~7% regression on TCP_CRR tests
that they bisected to the cited commit.
Indeed, every time a new TCP socket is created or deleted,
the atomic counter net->count is touched (via get_net(net)
and put_net(net) calls)
So cpus might have to reload a contended cache line in
net_hash_mix(net) calls.
We need to reorder 'struct net' fields to move @hash_mix
in a read mostly cache line.
We move in the first cache line fields that can be
dirtied often.
We probably will have to address in a followup patch
the __randomize_layout that was added in linux-4.13,
since this might break our placement choices.
Fixes: 355b98553789 ("netns: provide pure entropy for net_hash_mix()") Signed-off-by: Eric Dumazet <[email protected]> Reported-by: kernel test robot <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vivien Didelot [Fri, 18 Oct 2019 21:02:46 +0000 (17:02 -0400)]
net: dsa: fix switch tree list
If there are multiple switch trees on the device, only the last one
will be listed, because the arguments of list_add_tail are swapped.
Fixes: 83c0afaec7b7 ("net: dsa: Add new binding implementation") Signed-off-by: Vivien Didelot <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Mans Rullgard [Fri, 18 Oct 2019 16:56:58 +0000 (17:56 +0100)]
net: ethernet: dwmac-sun8i: show message only when switching to promisc
Printing the info message every time more than the max number of mac
addresses are requested generates unnecessary log spam. Showing it only
when the hw is not already in promiscous mode is equally informative
without being annoying.
Chenwandun [Fri, 18 Oct 2019 10:20:37 +0000 (18:20 +0800)]
net: aquantia: add an error handling in aq_nic_set_multicast_list
add an error handling in aq_nic_set_multicast_list, it may not
work when hw_multicast_list_set error; and at the same time
it will remove gcc Wunused-but-set-variable warning.
====================
net: netem: fix further issues with packet corruption
This set is fixing two more issues with the netem packet corruption.
First patch (which was previously posted) avoids NULL pointer dereference
if the first frame gets freed due to allocation or checksum failure.
v2 improves the clarity of the code a little as requested by Cong.
Second patch ensures we don't return SUCCESS if the frame was in fact
dropped. Thanks to this commit message for patch 1 no longer needs the
"this will still break with a single-frame failure" disclaimer.
====================
Jakub Kicinski [Fri, 18 Oct 2019 16:16:58 +0000 (09:16 -0700)]
net: netem: correct the parent's backlog when corrupted packet was dropped
If packet corruption failed we jump to finish_segs and return
NET_XMIT_SUCCESS. Seeing success will make the parent qdisc
increment its backlog, that's incorrect - we need to return
NET_XMIT_DROP.
Fixes: 6071bd1aa13e ("netem: Segment GSO packets on enqueue") Signed-off-by: Jakub Kicinski <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jakub Kicinski [Fri, 18 Oct 2019 16:16:57 +0000 (09:16 -0700)]
net: netem: fix error path for corrupted GSO frames
To corrupt a GSO frame we first perform segmentation. We then
proceed using the first segment instead of the full GSO skb and
requeue the rest of the segments as separate packets.
If there are any issues with processing the first segment we
still want to process the rest, therefore we jump to the
finish_segs label.
Commit 177b8007463c ("net: netem: fix backlog accounting for
corrupted GSO frames") started using the pointer to the first
segment in the "rest of segments processing", but as mentioned
above the first segment may had already been freed at this point.
Backlog corrections for parent qdiscs have to be adjusted.
Michael Tretter [Fri, 18 Oct 2019 14:11:43 +0000 (16:11 +0200)]
macb: propagate errors when getting optional clocks
The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver
marks clock as not available if it receives an error when trying to get
a clock. This is wrong, because a clock controller might return
-EPROBE_DEFER if a clock is not available, but will eventually become
available.
In these cases, the driver would probe successfully but will never be
able to adjust the clocks, because the clocks were not available during
probe, but became available later.
For example, the clock controller for the ZynqMP is implemented in the
PMU firmware and the clocks are only available after the firmware driver
has been probed.
Use devm_clk_get_optional() in instead of devm_clk_get() to get the
optional clock and propagate all errors to the calling function.
Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).
This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.
This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yonglong Liu <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
The 'mmap' syscall has special needs so it doesn't use
SCA_STRARRAY_FLAGS, see its implementation in
syscall_arg__scnprintf_mmap_flags(), related to special handling of
MAP_ANONYMOUS, so set ->parm to the strarray__mmap_flags and hook up
with strarray__strtoul_flags manually, now we can filter by those or-ed
string expressions:
Now anything that uses STRARRAY_FLAGS, like the 'fsmount' syscall will
support mapping or-ed strings back to a value that can be used in a
filter.
In some cases, where STRARRAY_FLAGS isn't used but instead the scnprintf
is a special one because of specific needs, like for mmap, then one has
to set the ->pars to the strarray. See the next cset.
perf trace: Use strtoul for the fcntl 'cmd' argument
Since its values are in two ranges of values we ended up codifying it
using a 'struct strarrays', so now hook it up with STUL_STRARRAYS so
that we can do:
Jiri Olsa [Thu, 17 Oct 2019 10:59:09 +0000 (12:59 +0200)]
libperf: Introduce perf_evlist__for_each_mmap()
Add the perf_evlist__for_each_mmap() function and export it in the
perf/evlist.h header, so that the user can iterate through 'struct
perf_mmap' objects.
Add a internal perf_mmap__link() function to do the actual linking.
Leo Yan [Fri, 18 Oct 2019 08:55:31 +0000 (16:55 +0800)]
perf tests: Disable bp_signal testing for arm64
As there are several discussions for enabling perf breakpoint signal
testing on arm64 platform: arm64 needs to rely on single-step to execute
the breakpointed instruction and then reinstall the breakpoint exception
handler. But if we hook the breakpoint with a signal, the signal
handler will do the stepping rather than the breakpointed instruction,
this causes infinite loops as below:
Kernel space | Userspace
---------------------------------|--------------------------------
| __test_function() -> hit
| breakpoint
breakpoint_handler() |
`-> user_enable_single_step() |
do_signal() |
| sig_handler() -> Step one
| instruction and
| trap to kernel
single_step_handler() |
`-> reinstall_suspended_bps() |
| __test_function() -> hit
| breakpoint again and
| repeat up flow infinitely
As Will Deacon mentioned [1]: "that we require the overflow handler to
do the stepping on arm/arm64, which is relied upon by GDB/ptrace. The
hw_breakpoint code is a complete disaster so my preference would be to
rip out the perf part and just implement something directly in ptrace,
but it's a pretty horrible job". Though Will commented this on arm
architecture, but the comment also can apply on arm64 architecture.
For complete information, I searched online and found a few years back,
Wang Nan sent one patch 'arm64: Store breakpoint single step state into
pstate' [2]; the patch tried to resolve this issue by avoiding single
stepping in signal handler and defer to enable the signal stepping when
return to __test_function(). The fixing was not merged due to the
concern for missing to handle different usage cases.
Based on the info, the most feasible way is to skip Perf breakpoint
signal testing for arm64 and this could avoid the duplicate
investigation efforts when people see the failure. This patch skips
this case on arm64 platform, which is same with arm architecture.
The arm architecture supports breakpoint accounting but it doesn't
support breakpoint overflow signal handling. The current code uses the
same checking helper, thus it disables both testings (bp_account and
bp_signal) for arm platform.
For handling two testings separately, this patch adds a dedicated
checking helper is_supported() for breakpoint accounting testing, thus
it allows supporting breakpoint accounting testing on arm platform; the
old helper test__bp_signal_is_supported() is only used to checking for
breakpoint overflow signal testing.
Leo Yan [Fri, 18 Oct 2019 08:55:29 +0000 (16:55 +0800)]
perf tests: Remove needless headers for bp_account
A few headers are not needed and were introduced by copying from other
test file. This patch removes the needless headers for the breakpoint
accounting testing.
Jin Yao [Tue, 15 Oct 2019 02:53:57 +0000 (10:53 +0800)]
perf list: Hide deprecated events by default
There are some deprecated events listed by perf list. But we can't
remove them from perf list with ease because some old scripts may use
them.
Deprecated events are old names of renamed events. When an event gets
renamed the old name is kept around for some time and marked with
Deprecated. The newer Intel event lists in the tree already have these
headers.
So we need to keep them in the event list, but provide a new option to
show them. The new option is "--deprecated".
With this patch, the deprecated events are hidden by default but they
can be displayed when option "--deprecated" is enabled.
perf trace: Pass a syscall_arg to syscall_arg_fmt->strtoul()
With just what we need for the STUL_STRARRAY, i.e. the 'struct strarray'
pointer to be used, just like with syscall_arg_fmt->scnprintf() for the
other direction (number -> string).
With this all the strarrays that are associated with syscalls can be
used with '-e syscalls:sys_enter_SYSCALLNAME --filter', and soon will be
possible as well to use with the strace-like shorter form, with just the
syscall names, i.e. something like:
So we'll need a strarray__strtoul_flags() that will break donw the flags
into tokens separated by '|' before doing the lookup and then go on
reconstructing the value from, say:
Linus Torvalds [Sat, 19 Oct 2019 10:53:59 +0000 (06:53 -0400)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"Rather a lot of fixes, almost all affecting mm/"
* emailed patches from Andrew Morton <[email protected]>: (26 commits)
scripts/gdb: fix debugging modules on s390
kernel/events/uprobes.c: only do FOLL_SPLIT_PMD for uprobe register
mm/thp: allow dropping THP from page cache
mm/vmscan.c: support removing arbitrary sized pages from mapping
mm/thp: fix node page state in split_huge_page_to_list()
proc/meminfo: fix output alignment
mm/init-mm.c: include <linux/mman.h> for vm_committed_as_batch
mm/filemap.c: include <linux/ramfs.h> for generic_file_vm_ops definition
mm: include <linux/huge_mm.h> for is_vma_temporary_stack
zram: fix race between backing_dev_show and backing_dev_store
mm/memcontrol: update lruvec counters in mem_cgroup_move_account
ocfs2: fix panic due to ocfs2_wq is null
hugetlbfs: don't access uninitialized memmaps in pfn_range_valid_gigantic()
mm: memblock: do not enforce current limit for memblock_phys* family
mm: memcg: get number of pages on the LRU list in memcgroup base on lru_zone_size
mm/gup: fix a misnamed "write" argument, and a related bug
mm/gup_benchmark: add a missing "w" to getopt string
ocfs2: fix error handling in ocfs2_setattr()
mm: memcg/slab: fix panic in __free_slab() caused by premature memcg pointer release
mm/memunmap: don't access uninitialized memmap in memunmap_pages()
...
projects / linux.git / log