Xingyu Wu [Mon, 21 Aug 2023 14:41:47 +0000 (22:41 +0800)]
ASoC: dt-bindings: snps,designware-i2s: Add StarFive JH7110 SoC support
Add the StarFive JH7110 (TX0/TX1/RX channel) SoC support in the bindings
of Designware I2S controller. The I2S controller needs two reset items
to work properly on the JH7110 SoC. And TX0 channel as master mode needs
5 clock items and TX1/RX channels as slave mode need 9 clock items on
the JH7110 SoC. The RX channel needs System Register Controller property
to enable it and other platforms do not need it.
Peter Ujfalusi [Tue, 22 Aug 2023 06:54:19 +0000 (09:54 +0300)]
ASoC: SOF: ipc4-topology: Add module parameter to ignore the CPC value
Add a new module parameter ipc4_ignore_cpc which can be used to force the
kernel to ignore the queried CPC value for all firmware modules and use 0
instead.
The CPC lookup is still done to report missing configurations and the
debug print is going to be different to be explicit that the CPC is ignored
and what was the value we would have used.
The CPC value is sent to the firmware with the MOD_INIT_INSTANCE message
and it is used by the firmware as a parameter for clock scaling.
The flag is intended to be used only when there is a need to validate the
firmware behavior regarding to clock scaling since the 0 CPC value will
force the DSP to run in full speed, disabling the scaling and provides
additional counter point to rule out clock management related issues.
The SRC component in a pipeline provides flexibility on the sampling
rate which was not handled previously. This series will improve the
kernel side with the needed logic to be able to deal with the SRC type
of components in pipelines.
This patch chain adds support for the Cirrus Logic cs42l43 PC focused
SoundWire CODEC. The chain is currently based of Lee's for-mfd-next
branch.
This series is mostly just a resend keeping pace with the kernel under
it, except for a minor fixup in the ASoC stuff.
Thanks,
Charles
Charles Keepax (4):
dt-bindings: mfd: cirrus,cs42l43: Add initial DT binding
mfd: cs42l43: Add support for cs42l43 core driver
pinctrl: cs42l43: Add support for the cs42l43
ASoC: cs42l43: Add support for the cs42l43
Lucas Tanure (2):
soundwire: bus: Allow SoundWire peripherals to register IRQ handlers
spi: cs42l43: Add SPI controller support
ASoC: SOF: ipc4-topology: Modify the reference output valid_bits for copier
If the copier has only output valid_bits across all its output
formats, the reference for selecting the output format must be set that
instead of the valid_bits from the selected input format.
ASoC: SOF: ipc4-topology: Fix pipeline params at the output of copier
When we walk the list of connected widgets from the source to the sink
to prepare all widgets, the pipeline_params must be modified to reflect
the output audio format at each widget. But, the copier only modifies
the sample format in the pipeline_params. So, fix it to also modify the
rate and channels.
ASoC: SOF: ipc4-topology: Fix the output reference params for SRC
For playback, the SRC sink rate must be configured based on the requested
output format which is restricted to only handle DAI's that support a
single audio format for now. For capture, the SRC module should convert
the rate to match the rate requested by the PCM hw_params.
Charles Keepax [Fri, 4 Aug 2023 10:46:02 +0000 (11:46 +0100)]
ASoC: cs42l43: Add support for the cs42l43
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
The ASoC component provides the majority of the functionality of the
device, all the audio functions.
ASoC: amd: acp: Add kcontrols and widgets per-codec in common code
Commit 7ac3404c2e21 ("ASoC: amd: acp: Map missing jack kcontrols") adds
card kcontrols and DAPM widgets corresponding to jacks for Headphone and
Headset Mic. But these were already being added in acp-legacy-mach.c and
acp-sof-mach.c, so this causes a probe error:
sof_mach rt5682s-hs-rt1019: control 2:0:0:Headphone Jack Switch:0 is already present
sof_mach rt5682s-hs-rt1019: ASoC: Failed to add Headphone Jack Switch: -16
sof_mach rt5682s-hs-rt1019: devm_snd_soc_register_card(sof-rt5682s-hs-rt1019) failed: -16
sof_mach: probe of rt5682s-hs-rt1019 failed with error -16
Removing the new duplicates from the common code might be enough to fix
the issue. But some of the codecs use different kcontrols and widgets.
NAU8821 alone has an "Int Mic". MAX98360A has a single "Spk", while
RT1019 has "Left Spk" and "Right Spk" (and two codec instances with name
prefixes).
Since there are per-codec differences, add the kcontrols and widgets
in the common code as each dai-link is being initialized, instead of in
the two machine drivers' probe().
Also, MAX98388 has Left and Right instances, but uses a single "SPK"
widget. That seems weird, so normalize it to use two widgets (one per
each instance like RT1019) while we're adding controls.
Shuming Fan [Fri, 18 Aug 2023 02:37:32 +0000 (02:37 +0000)]
ASoC: rt5645: improve the depop sequences of CBJ detection
This patch will improve the depop function of CBJ detection before the headphone playback
when the system resumes.
We also want to complete the CBJ detection in the system-level resume function.
It could avoid triggering the detection at the playing state of headphones.
Linus Walleij [Thu, 17 Aug 2023 14:03:18 +0000 (16:03 +0200)]
ASoC: rt5665: Convert to use GPIO descriptors
The RT5665 driver has some stub support for GPIO descriptors
going back to the initial driver commit, where there are
two GPIO descriptors for the LDO and headphone detection
defined in the device state. Well, let's make use of the
descriptor properly.
We remove the global GPIO number from the platform data,
but it is still possible to create board files using GPIO
descriptor tables, if desired.
Linus Walleij [Thu, 17 Aug 2023 14:03:17 +0000 (16:03 +0200)]
ASoC: rt5640: Convert to just use GPIO descriptors
The RT5640 driver is already using GPIO descriptors for some
stuff, all that is needed is to convert the remaining LDO1
control line to also use descriptors.
Simplify the code using gpiod_get_optional() and drop the
special "of" parsing function: these descriptors need not
come from device tree and it's optional so hey.
Keep some NULL checks around the GPIO operations even though
gpiolib is essentially NULL-tolerant, because by checking
for whether we have a valid GPIO descriptor or not we can
avoid a 400 ms delay which is great.
Maciej Strozek [Thu, 17 Aug 2023 11:27:11 +0000 (12:27 +0100)]
ASoC: cs35l56: Read firmware uuid from a device property instead of _SUB
Use a device property "cirrus,firmware-uid" to get the unique firmware
identifier instead of using ACPI _SUB. There aren't any products that use
_SUB.
There will not usually be a _SUB in Soundwire nodes. The ACPI can use a
_DSD section for custom properties.
There is also a need to support instantiating this driver using software
nodes. This is for systems where the CS35L56 is a back-end device and the
ACPI refers only to the front-end audio device - there will not be any ACPI
references to CS35L56.
Charles Keepax [Fri, 4 Aug 2023 10:46:00 +0000 (11:46 +0100)]
pinctrl: cs42l43: Add support for the cs42l43
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
Add a basic pinctrl driver which supports driver strength for the
various pins, gpios, and pinmux for the 2 multi-function pins.
Charles Keepax [Fri, 4 Aug 2023 10:45:59 +0000 (11:45 +0100)]
mfd: cs42l43: Add support for cs42l43 core driver
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
The MFD component registers and initialises the device and provides
PM/system power management.
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
Lucas Tanure [Fri, 4 Aug 2023 10:45:57 +0000 (11:45 +0100)]
soundwire: bus: Allow SoundWire peripherals to register IRQ handlers
Currently the in-band alerts for SoundWire peripherals can only
be communicated to the driver through the interrupt_callback
function. This however is slightly inconvenient for devices that wish
to share IRQ handling code between SoundWire and I2C/SPI, the later
would normally register an IRQ handler with the IRQ subsystem. However
there is no reason the SoundWire in-band IRQs can not also be
communicated as an actual IRQ to the driver.
Add support for SoundWire peripherals to register a normal IRQ
handler to receive SoundWire in-band alerts, allowing code to be
shared across control buses. Note that we allow users to use both the
interrupt_callback and the IRQ handler, this is useful for devices
which must clear additional chip specific SoundWire registers that are
not a part of the normal IRQ flow, or the SoundWire specification.
ASoC: samsung: odroid: use of_property_present to check for property
"samsung,audio-widgets" and "samsung,audio-routing" are not boolean
properties, thus more appropriate is to use of_property_present() to
check if they are present.
ASoC: dt-bindings: samsung,tm2: use common sound card
Reference the common sound card properties and deprecate the
custom "samsung,audio-routing" in favor of generic one. This allows to
remove "model" property and make the binding closer to other sounds
cards.
ASoC: dt-bindings: samsung,odroid: use common sound card
Reference the common sound card properties and deprecate the
custom "samsung,audio-routing" in favor of generic one. This allows to
remove "model" property and make the binding closer to other sounds
cards.
ASoC: dt-bindings: samsung,midas-audio: use common sound card
Reference the common sound card properties and deprecate the
custom "samsung,audio-routing" in favor of generic one. This allows to
remove "model" property and make the binding closer to other sounds
cards.
ASoC: dt-bindings: samsung,aries-wm8994: use common sound card
Reference the common sound card properties and deprecate the
custom "samsung,audio-routing" in favor of generic one. This allows to
remove "model" property and make the binding closer to other sounds
cards.
ASoC: dt-bindings: mediatek,mt8188-mt6359: use common sound card
The mediatek,mt8188-mt6359 Linux sound machine driver requires the
"model" property, so binding was incomplete. Reference the common sound
card properties to fix that which also allows to remove duplicated
property definitions. Leave the relevant parts of "audio-routing"
description.
ASoC: dt-bindings: Add common sound card properties
Almost every board machine / sound cards has "audio-routing" and "model"
properties, so move them to common schema to have only one definition of
these properties.
For amlogic,gx-sound-card, drop the minItems: 2 from the
"audio-routing", because any limit here - lower or upper- is rather
meaningless. This will also fix `dtbs_check` warnings like:
meson-gxm-s912-libretech-pc.dtb: sound: audio-routing: ['AU2 INL', 'ACODEC LOLN', 'AU2 INR', 'ACODEC LORN', '7J4-14 LEFT', 'AU2 OUTL', '7J4-11 RIGHT', 'AU2 OUTR'] is too long
Vlad Karpovich [Tue, 15 Aug 2023 17:29:08 +0000 (12:29 -0500)]
firmware: cs_dsp: Fix new control name check
Before adding a new FW control, its name is checked against
existing controls list. But the string length in strncmp used
to compare controls names is taken from the list, so if beginnings
of the controls are matching, then the new control is not created.
For example, if CAL_R control already exists, CAL_R_SELECTED
is not created.
The fix is to compare string lengths as well.
The use of the widget name as a prefix for the kcontrol name is quite
useful in the case of multiple pipelines going to the same endpoint,
but it's overkill in simpler cases.
This patchset extends the existing DAPM code to drop the widget name
prefix and make the kcontrol names simpler when there's no possible
ambiguity, e.g. "gain.2.1 Main Playback Volume" becomes just "Main
Playback Volume".
Only attempt to download wmfw/bin files to a non-secured part if
it reports FIRMWARE_MISSING. If FIRMWARE_MISSING is false the
firmware has already been patched and overwriting the patch could
corrupt the running firmware.
For a secured part the wmfw/bin can be downloaded even if
FIRMWARE_MISSING is false, because they will only patch tunings.
ASoC: wm_adsp: Support powering-up DSP without trying to load firmware
Add a flag to wm_adsp_power_up() that indicates whether it should attempt
to find and load firmware files.
This is to support DSPs that have built-in firmware that may already have
been patched (for example, by the BIOS). In that case the patch must not
be overwritten because that could corrupt the running firmware.
Balamurugan C [Mon, 14 Aug 2023 23:13:58 +0000 (18:13 -0500)]
ASoC: Intel: RPL: Add entry for HDMI-In capture support on non-I2S codec boards.
Adding HDMI-In capture support for the RPL products doesn't have onboard
I2S codec.but need to support HDMI-In capture via I2S and audio playback
through HDMI/DP monitor.
Jyri Sarha [Mon, 14 Aug 2023 23:23:25 +0000 (18:23 -0500)]
ASoC: SOF: topology: Add a token for dropping widget name in kcontrol name
Adds SOF_TKN_COMP_NO_WNAME_IN_KCONTROL_NAME token, and copies the
token's tuple value to the no_wname_in_kcontrol_name flag in struct
snd_soc_dapm_widget.
If the tuple value for the token in the topology is true, then the
widget name is not added to the mixer name. In practice "gain.2.1 Post
Mixer Analog Playback Volume" becomes just "Post Mixer Analog Playback
Volume".
Jyri Sarha [Mon, 14 Aug 2023 23:23:24 +0000 (18:23 -0500)]
ASoC: dapm: Add a flag for not having widget name in kcontrol name
The existing soc-dapm code may add a prefix to control names, which in
some cases is useful but in others leads to long and confusing kcontrol
names such as "gain 2.1 Main Playback Volume".
This patch suggests an added flag to prevent the widget name prefix
from being added. That flag will be set in the topology file on a
per-widget basis.
The flag no_wname_in_kcontrol_name is added to struct snd_soc_dapm_widget,
and the logic in dapm_create_or_share_kcontrol() is changed to not to
add widget name if the flag is set.
Guiting Shen [Sun, 13 Aug 2023 12:55:20 +0000 (20:55 +0800)]
ASoC: tlv320aic32x4: Fix the divide by zero
The value of register(NDAC,MDAC,NADC,MADC,BCLKN) maybe zero lead to
divide by zero in clk_aic32x4_div_recalc_rate().And the rate should be
divide by 128 if the value was zero in this function according to the
datasheet.
Add the macro AIC32X4_DIV_MAX to present the 128 and return 0 if failing
to read the value of register.
projects / linux.git / log