Qingqing Zhuo [Wed, 25 Aug 2021 16:29:28 +0000 (12:29 -0400)]
drm/amd/display: Extend w/a for hard hang on HPD to dcn20
[Why]
HPD disable and enable sequences are not mutually exclusive on Linux.
For HPDs that spans under 1s (i.e. HPD low = 1s), part of the disable
sequence (specifically, a request to SMU to lower refclk) could come
right before the call to PHY enablement, causing DMUB to access an
irresponsive PHY and thus a hard hang on the system.
[How]
Disable 48mhz refclk off when there is any HPD status in connected state
for dcn20.
Harry Wentland [Mon, 13 Sep 2021 17:32:50 +0000 (13:32 -0400)]
drm/amd/display: Reduce stack size for dml21_ModeSupportAndSystemConfigurationFull
[Why & How]
With Werror enabled in the kernel we were failing the clang build since
dml21_ModeSupportAndSystemConfigurationFull's stack frame is 1064 when
building with clang, and exceeding the default 1024 stack frame limit.
The culprit seems to be the Pipe struct, so pull the relevant block
out into its own sub-function.
Harry Wentland [Wed, 8 Sep 2021 00:22:13 +0000 (20:22 -0400)]
drm/amd/display: Allocate structs needed by dcn_bw_calc_rq_dlg_ttu in pipe_ctx
[Why & How]
dcn_bw_calc_rq_dlg_ttu uses a stack frame great than 1024. To solve this
we could allocate the rq_param, dlg_sys_param, and input structs
dynamically. Since this function is inside a kernel_fpu_begin()/end()
call we want to avoid memory allocation. Instead it's much
safer to pre-allocate these on the pipe_ctx.
Harry Wentland [Wed, 8 Sep 2021 14:21:37 +0000 (10:21 -0400)]
drm/amd/display: Pass all structs in display_rq_dlg_helpers by pointer
Passing structs adds a lot of overhead. We don't ever want to pass
anything bigger than primitives by value.
This patch fixes these Coverity IDs:
Addresses-Coverity-ID: 1423868: ("Big parameter passed by value")
Addresses-Coverity-ID: 1423870: ("Big parameter passed by value")
Harry Wentland [Tue, 7 Sep 2021 23:40:06 +0000 (19:40 -0400)]
drm/amd/display: Pass display_pipe_params_st as const in DML
[Why]
This neither needs to be on the stack nor passed by value
to each function call. In fact, when building with clang
it seems to break the Linux's default 1024 byte stack
frame limit.
[How]
We can simply pass this as a const pointer.
This patch fixes these Coverity IDs
Addresses-Coverity-ID: 1424031: ("Big parameter passed by value")
Addresses-Coverity-ID: 1423970: ("Big parameter passed by value")
Addresses-Coverity-ID: 1423941: ("Big parameter passed by value")
Addresses-Coverity-ID: 1451742: ("Big parameter passed by value")
Addresses-Coverity-ID: 1451887: ("Big parameter passed by value")
Addresses-Coverity-ID: 1454146: ("Big parameter passed by value")
Addresses-Coverity-ID: 1454152: ("Big parameter passed by value")
Addresses-Coverity-ID: 1454413: ("Big parameter passed by value")
Addresses-Coverity-ID: 1466144: ("Big parameter passed by value")
Addresses-Coverity-ID: 1487237: ("Big parameter passed by value")
Philip Yang [Tue, 14 Sep 2021 20:33:40 +0000 (16:33 -0400)]
drm/amdkfd: fix dma mapping leaking warning
For xnack off, restore work dma unmap previous system memory page, and
dma map the updated system memory page to update GPU mapping, this is
not dma mapping leaking, remove the WARN_ONCE for dma mapping leaking.
prange->dma_addr store the VRAM page pfn after the range migrated to
VRAM, should not dma unmap VRAM page when updating GPU mapping or
remove prange. Add helper svm_is_valid_dma_mapping_addr to check VRAM
page and error cases.
Mask out SVM_RANGE_VRAM_DOMAIN flag in dma_addr before calling amdgpu vm
update to avoid BUG_ON(*addr & 0xFFFF00000000003FULL), and set it again
immediately after. This flag is used to know the type of page later to
dma unmapping system memory page.
Fixes: 1d5dbfe6c06a ("drm/amdkfd: classify and map mixed svm range pages in GPU") Signed-off-by: Philip Yang <[email protected]> Reviewed-by: Felix Kuehling <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Philip Yang [Mon, 13 Sep 2021 14:03:36 +0000 (10:03 -0400)]
drm/amdkfd: SVM map to gpus check vma boundary
SVM range may includes multiple VMAs with different vm_flags, if prange
page index is the last page of the VMA offset + npages, update GPU
mapping to create GPU page table with same VMA access permission.
Using an empty macro expansion as a conditional expression
produces a W=1 warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c: In function 'dce_aux_transfer_with_retries':
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:775:156: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
775 | "dce_aux_transfer_with_retries: AUX_RET_SUCCESS: AUX_TRANSACTION_REPLY_I2C_OVER_AUX_DEFER");
| ^
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:783:155: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
783 | "dce_aux_transfer_with_retries: AUX_RET_SUCCESS: AUX_TRANSACTION_REPLY_I2C_OVER_AUX_NACK");
| ^
Expand it to "do { } while (0)" instead to make the expression
more robust and avoid the warning.
Fixes: 56aca2309301 ("drm/amd/display: Add AUX I2C tracing.") Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
drm/amdgpu: Fix resume failures when device is gone
Problem:
When device goes into suspend and unplugged during it
then all HW programming during resume fails leading
to a bad SW during pci remove handling which follows.
Because device is first resumed and only later removed
we cannot rely on drm_dev_enter/exit here.
Fix:
Use a flag we use for PCIe error recovery to avoid
accessing registres. This allows to successfully complete
pm resume sequence and finish pci remove.
Why:
VCE/UVD had dependency on SMC block for their suspend but
SMC block is the first to do HW fini due to some constraints
How:
Since the original patch was dealing with suspend issues
move the SMC block dependency back into suspend hooks as
was done in V1 of the original patches.
Keep flushing idle work both in suspend and HW fini seuqnces
since it's essential in both cases.
Fixes: 859e4659273f1d ("drm/amdgpu: add missing cleanups for more ASICs on UVD/VCE suspend") Fixes: bf756fb833cbe8 ("drm/amdgpu: add missing cleanups for Polaris12 UVD/VCE on suspend") Signed-off-by: Andrey Grodzovsky <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
xinhui pan [Thu, 16 Sep 2021 01:35:47 +0000 (09:35 +0800)]
drm/amdgpu: Fix uvd ib test timeout when use pre-allocated BO
Now we use same BO for create/destroy msg. So destroy will wait for the
fence returned from create to be signaled. The default timeout value in
destroy is 10ms which is too short.
xinhui pan [Wed, 15 Sep 2021 01:08:28 +0000 (09:08 +0800)]
drm/amdgpu: Put drm_dev_enter/exit outside hot codepath
We hit soft hang while doing memory pressure test on one numa system.
After a qucik look, this is because kfd invalid/valid userptr memory
frequently with process_info lock hold.
Looks like update page table mapping use too much cpu time.
So move drm_dev_enter/exit outside gmc code, instead let caller do it.
They are gart_unbind, gart_map, vm_clear_bo, vm_update_pdes and
gmc_init_pdb0. vm_bo_update_mapping already calls it.
Simon Ser [Fri, 10 Sep 2021 15:37:41 +0000 (15:37 +0000)]
amd/display: enable panel orientation quirks
This patch allows panel orientation quirks from DRM core to be
used. They attach a DRM connector property "panel orientation"
which indicates in which direction the panel has been mounted.
Some machines have the internal screen mounted with a rotation.
Since the panel orientation quirks need the native mode from the
EDID, check for it in amdgpu_dm_connector_ddc_get_modes.
Paul Menzel [Mon, 13 Sep 2021 08:34:11 +0000 (10:34 +0200)]
drm/amdgpu: Demote TMZ unsupported log message from warning to info
As the user cannot do anything about the unsupported Trusted Memory Zone
(TMZ) feature, do not warn about it, but make it informational, so
demote the log level from warning to info.
Michel Dänzer [Thu, 9 Sep 2021 16:56:28 +0000 (18:56 +0200)]
drm/amdgpu: Drop inline from amdgpu_ras_eeprom_max_record_count
This was unusual; normally, inline functions are declared static as
well, and defined in a header file if used by multiple compilation
units. The latter would be more involved in this case, so just drop
the inline declaration for now.
Fixes compile failure building for ppc64le on RHEL 8:
In file included from ../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.h:32,
from ../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:33:
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c: In function ‘amdgpu_ras_recovery_init’:
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras_eeprom.h:90:17: error: inlining failed in call
to ‘always_inline’ ‘amdgpu_ras_eeprom_max_record_count’: function body not available
90 | inline uint32_t amdgpu_ras_eeprom_max_record_count(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:1985:34: note: called from here
1985 | max_eeprom_records_len = amdgpu_ras_eeprom_max_record_count();
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: c84d46707ebb "drm/amdgpu: validate bad page threshold in ras(v3)" Reviewed-by: Lyude Paul <[email protected]> Signed-off-by: Michel Dänzer <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Evan Quan [Thu, 9 Sep 2021 03:01:00 +0000 (11:01 +0800)]
drm/amd/pm: fix runpm hang when amdgpu loaded prior to sound driver
Current RUNPM mechanism relies on PMFW to master the timing for BACO
in/exit. And that needs cooperation from sound driver for dstate
change notification for function 1(audio). Otherwise(on sound driver
missing), BACO cannot be kicked in correctly and hang will be observed
on RUNPM exit.
By switching back to legacy message way on sound driver missing,
we are able to fix the runpm hang observed for the scenario below:
amdgpu driver loaded -> runpm suspend kicked -> sound driver loaded
drm/amdgpu: Get atomicOps info from Host for sriov setup
The AtomicOp Requester Enable bit is reserved in VFs and the PF value applies to all
associated VFs. so guest driver can not directly enable the atomicOps for VF, it
depends on PF to enable it. In current design, amdgpu driver will get the enabled
atomicOps bits through private pf2vf data
drm/amd/display: Link training retry fix for abort case
[Why]
If link training is aborted, it shall be retried if sink is present.
[How]
Check hpd status to find out whether sink is present or not. If sink is
present, then link training shall be tried again with same settings.
Otherwise, link training shall be aborted.
Qingqing Zhuo [Fri, 27 Aug 2021 10:58:38 +0000 (06:58 -0400)]
drm/amd/display: Fix unstable HPCP compliance on Chrome Barcelo
[Why]
Intermittently, there presents two occurrences of 0 stream
commits in a single HPD event. Current HDCP sequence does
not consider such scenerio, and will thus disable HDCP.
[How]
Add condition check to include stream remove and re-enable
case for HDCP enable.
Aric Cyr [Sun, 29 Aug 2021 22:44:22 +0000 (18:44 -0400)]
drm/amd/display: 3.2.152
* Correct degamma coefficients
* Optimize bandwidth on following fast update
* Fix multiple memory leaks reported by coverity
* Get backlight from PWM if DMCU is not initialized
Hersen Wu [Wed, 25 Aug 2021 20:27:47 +0000 (16:27 -0400)]
drm/amd/display: dsc mst 2 4K displays go dark with 2 lane HBR3
[Why]
call stack of amdgpu dsc mst pbn, slot num calculation is as below:
-compute_bpp_x16_from_target_bandwidth
-decide_dsc_target_bpp_x16
-setup_dsc_config
-dc_dsc_compute_bandwidth_range
-compute_mst_dsc_configs_for_link
-compute_mst_dsc_configs_for_state
from pbn -> dsc target bpp_x16
bpp_x16 is calulated by compute_bpp_x16_from_target_bandwidth.
Beside pixel clock and bpp, num_slices_h and bpp_increment_div
will also affect bpp_x16.
from dsc target bpp_x16 -> pbn
within dm_update_mst_vcpi_slots_for_dsc,
pbn = drm_dp_calc_pbn_mode(clock, bpp_x16, true);
bpp / 16 trunc digits after decimal point. This will cause calculation
delta. drm_dp_calc_pbn_mode does not have other informations,
like num_slices_h, bpp_increment_div. therefore, it does not do revese
calcuation properly from bpp_x16 to pbn.
pbn from drm_dp_calc_pbn_mode is less than pbn from
compute_mst_dsc_configs_for_state. This cause not enough mst slot
allocated to display. display could not visually light up.
[How]
pass pbn from compute_mst_dsc_configs_for_state to
dm_update_mst_vcpi_slots_for_dsc
Dale Zhao [Mon, 23 Aug 2021 08:44:37 +0000 (16:44 +0800)]
drm/amd/display: Refine condition of cursor visibility for pipe-split
[Why]
In some scenarios like fullscreen game, major plane is scaled. Then
if a upper layer owns the cursor, cursor is invisiable in the
majority of the screen.
[How]
Instead assuming upper plane handles cursor, summing up upper
split planes on the same layer. If whole upper plane covers current
half/whole pipe plane, disable cursor.
Qingqing Zhuo [Tue, 17 Aug 2021 20:29:07 +0000 (16:29 -0400)]
drm/amd/display: Apply w/a for hard hang on HPD
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans under 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enablement, causing DMUB to access an irresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off when there is any HPD status in
connected state.
Jaehyun Chung [Tue, 24 Aug 2021 18:05:48 +0000 (14:05 -0400)]
drm/amd/display: Add regamma/degamma coefficients and set sRGB when TF is BT709
[Why]
In YUV case, need to set the input TF to sRGB instead of BT709,
even though the input TF type is distributed. SRGB was not
being used because pixel format was not being set in the
surface update sequence.
Also, we were using the same coefficients for degamma and
regamma formula, causing the cutoff point of the linear
section of the curve to be incorrect.
[How]
Set pixel format in the surface update sequence. Add separate
coefficient arrays for regamma and degamma.
Harry Wentland [Mon, 16 Aug 2021 19:57:12 +0000 (15:57 -0400)]
drm/amd/display: Get backlight from PWM if DMCU is not initialized
On Carrizo/Stoney systems we set backlight through panel_cntl, i.e.
directly via the PWM registers, if DMCU is not initialized. We
always read it back through ABM registers which leads to a
mismatch and forces atomic_commit to program the backlight
each time.
Instead make sure we use the same logic for backlight readback,
i.e. read it from panel_cntl if DMCU is not initialized.
We also need to remove some extraneous and incorrect calculations
at the end of dce_get_16_bit_backlight_from_pwm.
Jimmy Kizito [Tue, 10 Aug 2021 23:07:43 +0000 (19:07 -0400)]
drm/amd/display: Fix dynamic link encoder access.
[Why]
Assuming DIG link encoders are statically mapped to links can cause
system instability due to null pointer accesses.
[How]
- Add checks for non-null link encoder pointers before trying to access
them.
- When a hardware platform uses dynamic DIG assignment (i.e. resource
function 'link_encs_assign' defined) and a link supports flexible
mapping to DIGs, use the link_enc_cfg API to access the DIG assigned to
a link or stream.
Aurabindo Pillai [Fri, 13 Aug 2021 19:15:03 +0000 (15:15 -0400)]
drm/amd/display: Add flag to detect dpms force off during HPD
[Why] When a connector is unplugged, dpms is forced off so that some
connector allocations are cleared off. This is done outside the commit
sequence from the userspace. This causes HUBP blank. Due to the blank
hubp, a non blocking commit which queues flip will encounter a timeout
waiting for the flip_done because prior to writing the surface flip
address, hubp was in blank.
[How] Add a marker to DM's crtc state and use this field to indicate
whether dpms was forced off during an HPD. Check for this marker before
queuing the flip.
Josip Pavic [Thu, 19 Aug 2021 13:25:22 +0000 (09:25 -0400)]
drm/amd/display: unblock abm when odm is enabled only on configs that support it
[Why]
When ODM is enabled, ABM is blocked on dcn31 but unblocked on dcn30.
Since the dcn31 firmware is now able to handle ABM interop with ODM, it
is no longer necessary to block ABM when ODM is enabled.
Since the dcn30 firmware does not handle ABM interop with ODM, leaving
that combination unblocked can lead to one side of the screen appearing
brighter than the other.
[How]
When ODM is enabled, unblock abm on dcn31 and block it on dcn30
Wayne Lin [Fri, 23 Jul 2021 03:50:28 +0000 (11:50 +0800)]
drm/amd/display: Fork thread to offload work of hpd_rx_irq
[Why]
Currently, we will try to get dm.dc_lock in handle_hpd_rx_irq() when
link lost happened, which is risky and could cause deadlock.
e.g. If we are under procedure to enable MST streams and then monitor
happens to toggle short hpd to notify link lost, then
handle_hpd_rx_irq() will get blocked due to stream enabling flow has
dc_lock. However, under MST, enabling streams involves communication
with remote sinks which need to use handle_hpd_rx_irq() to handle
sideband messages. Thus, we have deadlock here.
[How]
Target is to have handle_hpd_rx_irq() finished as soon as possilble.
Hence we can react to interrupt quickly. Besides, we should avoid to
grabe dm.dc_lock within handle_hpd_rx_irq() to avoid deadlock situation.
Firstly, revert patches which introduced to use dm.dc_lock in
handle_hpd_rx_irq():
* commit ("drm/amd/display: NULL pointer error during ")
* commit ("drm/amd/display: Only one display lights up while using MST")
* commit ("drm/amd/display: take dc_lock in short pulse handler only")
Instead, create work to handle irq events which needs dm.dc_lock.
Besides:
* Create struct hpd_rx_irq_offload_work_queue for each link to handle
its short hpd events
* Avoid to handle link lost/ automated test if the link is disconnected
* Defer dc_lock needed works in dc_link_handle_hpd_rx_irq(). This
function should just handle simple stuff for us (e.g. DPCD R/W).
However, deferred works should still be handled by the order that
dc_link_handle_hpd_rx_irq() used to be.
* Change function name dm_handle_hpd_rx_irq() to
dm_handle_mst_sideband_msg() to be more specific
Wayne Lin [Fri, 13 Aug 2021 07:54:47 +0000 (15:54 +0800)]
drm/amd/display: Add option to defer works of hpd_rx_irq
[Why & How]
Due to some code flow constraints, we need to defer dc_lock needed works
from dc_link_handle_hpd_rx_irq(). Thus, do following changes:
* Change allow_hpd_rx_irq() from static to public
* Change handle_automated_test() from static to public
* Extract link lost handling flow out from dc_link_handle_hpd_rx_irq()
and put those into a new function dc_link_dp_handle_link_loss()
* Add one option parameter to decide whether defer works within
dc_link_handle_hpd_rx_irq()
Wenjing Liu [Fri, 13 Aug 2021 23:49:43 +0000 (19:49 -0400)]
drm/amd/display: update conditions to do dfp cap ext validation
[why]
According to DP specs dfp cap ext validation is only for branch
device withou 128b/132b channel coding support and
downstream of the branch device doesn't have compression.
Therefore we are adding conditions to only do dfp cap
extension validation for branch devcie supporting 8b/10b
channel coding only and it has no DSC passthrough capability.
Wenjing Liu [Mon, 9 Aug 2021 21:00:12 +0000 (17:00 -0400)]
drm/amd/display: move bpp range decision in decide dsc bw range function
[why]
Before get dsc bw range is used to compute DSC bw range
based on the given fixed bpp min/max input.
The new change will merge any specs, signal, timing specific
bpp range decision into this function. So the function needs to make
a decision with all aspects considered.
Felix Kuehling [Tue, 31 Aug 2021 21:42:15 +0000 (17:42 -0400)]
drm/amdkfd: make needs_pcie_atomics FW-version dependent
On some GPUs the PCIe atomic requirement for KFD depends on the MEC
firmware version. Add a firmware version check for this. The minimum
firmware version that works without atomics can be updated in the
device_info structure for each GPU type.
Move PCIe atomic detection from kgd2kfd_probe into kgd2kfd_device_init
because the MEC firmware is not loaded yet at the probe stage.
Lang Yu [Fri, 27 Aug 2021 07:20:51 +0000 (15:20 +0800)]
drm/amdgpu: add manual sclk/vddc setting support for cyan skilfish(v3)
Add manual sclk/vddc setting supoort via pp_od_clk_voltage sysfs
to maintain consistency with other asics. As cyan skillfish doesn't
support DPM, there is only a single frequency and voltage to adjust.
v2: maintain consistency and add command guide.
v3: adjust user settings storage and coding style.
Command guide:
echo vc point sclk vddc > pp_od_clk_voltage
"vc" - sclk voltage curve
"point" - must be 0
"sclk" - target value of sclk(MHz), should be in safe range
"vddc" - target value of vddc(mV), a 6.25(mV) stepping is
recommended and should be in safe range (the real
vddc is an approximation of target value)
echo c > pp_od_clk_voltage
"c" - commit the changes of sclk and vddc, only after
the commit command, the target values set by "vc"
command will take effect
echo r > pp_od_clk_voltage
"r" - reset sclk and vddc to default value, a subsequent
commit command is needed to take effect
Example:
1) Check default sclk and vddc
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 862mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
2) Set sclk to 1500MHz and vddc to 700mV
$ echo vc 0 1500 700 > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1500Mhz *
OD_VDDC:
0: 693mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
3) Reset sclk and vddc to default
$ echo r > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 874mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
NOTE:
We don't specify an explicit safe range, you can set any values
between min and max at your own risk. Enjoy!
Nirmoy Das [Thu, 2 Sep 2021 13:31:07 +0000 (15:31 +0200)]
drm/amdgpu: cleanup debugfs for amdgpu rings
Use debugfs_create_file_size API for creating ring debugfs, and as its a
NULL returning API, change the return type for amdgpu_debugfs_ring_init
API as well. Also cleanup surrounding code.
drm/amd/display: make configure_lttpr_mode_transparent and configure_lttpr_mode_non_transparent static
This symbols is not used outside of dc_link_dp.c, so marks it static.
Fix the following sparse warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:1766:16:
warning: symbol 'configure_lttpr_mode_non_transparent' was not declared.
Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:1755:16:
warning: symbol 'configure_lttpr_mode_transparent' was not declared.
Should it be static?
Colin Ian King [Tue, 7 Sep 2021 11:09:13 +0000 (12:09 +0100)]
drm/radeon/ci_dpm: Remove redundant initialization of variables hi_sidd, lo_sidd
The variables hi_sidd and lo_sidd are being initialized with a values
that are never read, they are being updated later on. The assignments
are redundant and can be removed.
In amdgpu_dm_atomic_check, dc_validate_global_state is called. On
failure this logs a warning to the kernel journal. However warnings
shouldn't be used for atomic test-only commit failures: user-space
might be perfoming a lot of atomic test-only commits to find the
best hardware configuration.
Downgrade the log to a regular DRM atomic message. While at it, use
the new device-aware logging infrastructure.
This fixes error messages in the kernel when running gamescope [1].
Len Baker [Sat, 4 Sep 2021 15:41:06 +0000 (17:41 +0200)]
drm/radeon: Prefer kcalloc over open coded arithmetic
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, refactor the code a bit to use the purpose specific kcalloc()
function instead of the calculated size argument in the kzalloc()
function.
Christian König [Tue, 7 Sep 2021 07:37:52 +0000 (09:37 +0200)]
drm/amdgpu: fix use after free during BO move
The memory backing old_mem is already freed at that point, move the
check a bit more up.
Signed-off-by: Christian König <[email protected]> Fixes: bfa3357ef9ab ("drm/ttm: allocate resource object instead of embedding it v2")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1699 Acked-by: Nirmoy Das <[email protected]> Reviewed-by: Michel Dänzer <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
projects / linux.git / log