This commit is completely bogus. The STACR register has two formats, old
and new, depending on the version of the IP block used. There's a pair of
device-tree properties that can be used to specify the format used:
has-inverted-stacr-oc
has-new-stacr-staopc
What this commit did was to change the bit definition used with the old
parts to match the new parts. This of course breaks the driver on all
the old ones.
Instead, the author should have set the appropriate properties in the
device-tree for the variant used on his board.
David S. Miller [Sat, 8 Dec 2018 00:24:40 +0000 (16:24 -0800)]
Merge branch 'skb-headroom-slab-out-of-bounds'
Stefano Brivio says:
====================
Fix slab out-of-bounds on insufficient headroom for IPv6 packets
Patch 1/2 fixes a slab out-of-bounds occurring with short SCTP packets over
IPv4 over L2TP over IPv6 on a configuration with relatively low HEADER_MAX.
Patch 2/2 makes sure we avoid writing before the allocated buffer in
neigh_hh_output() in case the headroom is enough for the unaligned hardware
header size, but not enough for the aligned one, and that we warn if we hit
this condition.
====================
Stefano Brivio [Thu, 6 Dec 2018 18:30:37 +0000 (19:30 +0100)]
neighbour: Avoid writing before skb->head in neigh_hh_output()
While skb_push() makes the kernel panic if the skb headroom is less than
the unaligned hardware header size, it will proceed normally in case we
copy more than that because of alignment, and we'll silently corrupt
adjacent slabs.
In the case fixed by the previous patch,
"ipv6: Check available headroom in ip6_xmit() even without options", we
end up in neigh_hh_output() with 14 bytes headroom, 14 bytes hardware
header and write 16 bytes, starting 2 bytes before the allocated buffer.
Always check we're not writing before skb->head and, if the headroom is
not enough, warn and drop the packet.
v2:
- instead of panicking with BUG_ON(), WARN_ON_ONCE() and drop the packet
(Eric Dumazet)
- if we avoid the panic, though, we need to explicitly check the headroom
before the memcpy(), otherwise we'll have corrupted slabs on a running
kernel, after we warn
- use __skb_push() instead of skb_push(), as the headroom check is
already implemented here explicitly (Eric Dumazet)
Stefano Brivio [Thu, 6 Dec 2018 18:30:36 +0000 (19:30 +0100)]
ipv6: Check available headroom in ip6_xmit() even without options
Even if we send an IPv6 packet without options, MAX_HEADER might not be
enough to account for the additional headroom required by alignment of
hardware headers.
On a configuration without HYPERV_NET, WLAN, AX25, and with IPV6_TUNNEL,
sending short SCTP packets over IPv4 over L2TP over IPv6, we start with
100 bytes of allocated headroom in sctp_packet_transmit(), end up with 54
bytes after l2tp_xmit_skb(), and 14 bytes in ip6_finish_output2().
Those would be enough to append our 14 bytes header, but we're going to
align that to 16 bytes, and write 2 bytes out of the allocated slab in
neigh_hh_output().
Eric Dumazet [Thu, 6 Dec 2018 17:58:24 +0000 (09:58 -0800)]
tcp: lack of available data can also cause TSO defer
tcp_tso_should_defer() can return true in three different cases :
1) We are cwnd-limited
2) We are rwnd-limited
3) We are application limited.
Neal pointed out that my recent fix went too far, since
it assumed that if we were not in 1) case, we must be rwnd-limited
Fix this by properly populating the is_cwnd_limited and
is_rwnd_limited booleans.
After this change, we can finally move the silly check for FIN
flag only for the application-limited case.
The same move for EOR bit will be handled in net-next,
since commit 1c09f7d073b1 ("tcp: do not try to defer skbs
with eor mark (MSG_EOR)") is scheduled for linux-4.21
Tested by running 200 concurrent netperf -t TCP_RR -- -r 60000,100
and checking none of them was rwnd_limited in the chrono_stat
output from "ss -ti" command.
Linus Torvalds [Fri, 7 Dec 2018 22:34:10 +0000 (14:34 -0800)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vhost/virtio fixes from Michael Tsirkin:
"A couple of last-minute fixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/vsock: fix use-after-free in network stack callers
virtio/s390: fix race in ccw_io_helper()
virtio/s390: avoid race on vcdev->config
vhost/vsock: fix reset orphans race with close timeout
Linus Torvalds [Fri, 7 Dec 2018 22:18:49 +0000 (14:18 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Avoid sending IPIs with interrupts disabled"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: hibernate: Avoid sending cross-calling with interrupts disabled
* tag 'gcc-plugins-v4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
stackleak: Register the 'stackleak_cleanup' pass before the '*free_cfg' pass
stackleak: Mark stackleak_track_stack() as notrace
Linus Torvalds [Fri, 7 Dec 2018 21:07:10 +0000 (13:07 -0800)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Disable the new crypto stats interface as it's still being changed
- Fix potential uses-after-free in cbc/cfb/pcbc.
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: user - Disable statistics interface
crypto: do not free algorithm before using
Damien Le Moal [Fri, 30 Nov 2018 06:31:48 +0000 (15:31 +0900)]
dm zoned: Fix target BIO completion handling
struct bioctx includes the ref refcount_t to track the number of I/O
fragments used to process a target BIO as well as ensure that the zone
of the BIO is kept in the active state throughout the lifetime of the
BIO. However, since decrementing of this reference count is done in the
target .end_io method, the function bio_endio() must be called multiple
times for read and write target BIOs, which causes problems with the
value of the __bi_remaining struct bio field for chained BIOs (e.g. the
clone BIO passed by dm core is large and splits into fragments by the
block layer), resulting in incorrect values and inconsistencies with the
BIO_CHAIN flag setting. This is turn triggers the BUG_ON() call:
BUG_ON(atomic_read(&bio->__bi_remaining) <= 0);
in bio_remaining_done() called from bio_endio().
Fix this ensuring that bio_endio() is called only once for any target
BIO by always using internal clone BIOs for processing any read or
write target BIO. This allows reference counting using the target BIO
context counter to trigger the target BIO completion bio_endio() call
once all data, metadata and other zone work triggered by the BIO
complete.
Overall, this simplifies the code too as the target .end_io becomes
unnecessary and differences between read and write BIO issuing and
completion processing disappear.
Linus Torvalds [Fri, 7 Dec 2018 20:58:34 +0000 (12:58 -0800)]
Merge tag 'pci-v4.20-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Revert ASPM change that caused a regression"
* tag 'pci-v4.20-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI/ASPM: Do not initialize link state when aspm_disabled is set"
Shmulik Ladkani [Fri, 7 Dec 2018 07:50:17 +0000 (09:50 +0200)]
ipv6: sr: properly initialize flowi6 prior passing to ip6_route_output
In 'seg6_output', stack variable 'struct flowi6 fl6' was missing
initialization.
Fixes: 6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels") Signed-off-by: Shmulik Ladkani <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Fri, 7 Dec 2018 18:40:37 +0000 (10:40 -0800)]
Merge tag 'for-linus-20181207' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Let's try this again...
We're finally happy with the DM livelock issue, and it's also passed
overnight testing and the corruption regression test. The end result
is much nicer now too, which is great.
Outside of that fix, there's a pull request for NVMe with two small
fixes, and a regression fix for BFQ from this merge window. The BFQ
fix looks bigger than it is, it's 90% comment updates"
* tag 'for-linus-20181207' of git://git.kernel.dk/linux-block:
blk-mq: punt failed direct issue to dispatch list
nvmet-rdma: fix response use after free
nvme: validate controller state before rescheduling keep alive
block, bfq: fix decrement of num_active_groups
Linus Torvalds [Fri, 7 Dec 2018 18:31:31 +0000 (10:31 -0800)]
Merge branch 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A set of driver bugfixes for the I2C subsystem"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: uniphier-f: fix violation of tLOW requirement for Fast-mode
i2c: uniphier: fix violation of tLOW requirement for Fast-mode
i2c: uniphier-f: fill TX-FIFO only in IRQ handler for repeated START
i2c: uniphier-f: fix timeout error after reading 8 bytes
i2c: scmi: Fix probe error on devices with an empty SMB0001 ACPI device node
i2c: axxia: properly handle master timeout
i2c: rcar: check bus state before reinitializing
i2c: nvidia-gpu: limit reads also for combined messages
i2c: nvidia-gpu: adhere to I2C fault codes
Linus Torvalds [Fri, 7 Dec 2018 17:58:34 +0000 (09:58 -0800)]
Merge tag 'dmaengine-fix-4.20-rc6' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Another pull request for dmaengine. We got bunch of fixes early this
week and all are tagged to stable. Hope this is last fix for this
cycle:
- Fix imx-sdma handling of channel terminations, this involves
reverting two commits and implement async termination
- Fix cppi dma channel deletion from pending list on stop
- Fix FIFO size for dw controller in Intel Merrifield"
* tag 'dmaengine-fix-4.20-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw: Fix FIFO size for Intel Merrifield
dmaengine: cppi41: delete channel from pending list when stop channel
dmaengine: imx-sdma: use GFP_NOWAIT for dma descriptor allocations
dmaengine: imx-sdma: implement channel termination via worker
Revert "dmaengine: imx-sdma: alloclate bd memory from dma pool"
Revert "dmaengine: imx-sdma: Use GFP_NOWAIT for dma allocations"
x86/vdso: Drop implicit common-page-size linker flag
GNU linker's -z common-page-size's default value is based on the target
architecture. arch/x86/entry/vdso/Makefile sets it to the architecture
default, which is implicit and redundant. Drop it.
Will Deacon [Fri, 7 Dec 2018 12:47:10 +0000 (12:47 +0000)]
arm64: hibernate: Avoid sending cross-calling with interrupts disabled
Since commit 3b8c9f1cdfc50 ("arm64: IPI each CPU after invalidating the
I-cache for kernel mappings"), a call to flush_icache_range() will use
an IPI to cross-call other online CPUs so that any stale instructions
are flushed from their pipelines. This triggers a WARN during the
hibernation resume path, where flush_icache_range() is called with
interrupts disabled and is therefore prone to deadlock:
Since all secondary CPUs have been taken offline prior to invalidating
the I-cache, there's actually no need for an IPI and we can simply call
__flush_icache_range() instead.
Jens Axboe [Fri, 7 Dec 2018 05:17:44 +0000 (22:17 -0700)]
blk-mq: punt failed direct issue to dispatch list
After the direct dispatch corruption fix, we permanently disallow direct
dispatch of non read/write requests. This works fine off the normal IO
path, as they will be retried like any other failed direct dispatch
request. But for the blk_insert_cloned_request() that only DM uses to
bypass the bottom level scheduler, we always first attempt direct
dispatch. For some types of requests, that's now a permanent failure,
and no amount of retrying will make that succeed. This results in a
livelock.
Instead of making special cases for what we can direct issue, and now
having to deal with DM solving the livelock while still retaining a BUSY
condition feedback loop, always just add a request that has been through
->queue_rq() to the hardware queue dispatch list. These are safe to use
as no merging can take place there. Additionally, if requests do have
prepped data from drivers, we aren't dependent on them not sharing space
in the request structure to safely add them to the IO scheduler lists.
This basically reverts ffe81d45322c and is based on a patch from Ming,
but with the list insert case covered as well.
Israel Rukshin [Wed, 5 Dec 2018 16:54:57 +0000 (16:54 +0000)]
nvmet-rdma: fix response use after free
nvmet_rdma_release_rsp() may free the response before using it at error
flow.
Fixes: 8407879 ("nvmet-rdma: fix possible bogus dereference under heavy load") Signed-off-by: Israel Rukshin <[email protected]> Reviewed-by: Sagi Grimberg <[email protected]> Reviewed-by: Max Gurtovoy <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
James Smart [Wed, 28 Nov 2018 01:04:44 +0000 (17:04 -0800)]
nvme: validate controller state before rescheduling keep alive
Delete operations are seeing NULL pointer references in call_timer_fn.
Tracking these back, the timer appears to be the keep alive timer.
nvme_keep_alive_work() which is tied to the timer that is cancelled
by nvme_stop_keep_alive(), simply starts the keep alive io but doesn't
wait for it's completion. So nvme_stop_keep_alive() only stops a timer
when it's pending. When a keep alive is in flight, there is no timer
running and the nvme_stop_keep_alive() will have no affect on the keep
alive io. Thus, if the io completes successfully, the keep alive timer
will be rescheduled. In the failure case, delete is called, the
controller state is changed, the nvme_stop_keep_alive() is called while
the io is outstanding, and the delete path continues on. The keep
alive happens to successfully complete before the delete paths mark it
as aborted as part of the queue termination, so the timer is restarted.
The delete paths then tear down the controller, and later on the timer
code fires and the timer entry is now corrupt.
Fix by validating the controller state before rescheduling the keep
alive. Testing with the fix has confirmed the condition above was hit.
Paolo Valente [Thu, 6 Dec 2018 18:18:18 +0000 (19:18 +0100)]
block, bfq: fix decrement of num_active_groups
Since commit '2d29c9f89fcd ("block, bfq: improve asymmetric scenarios
detection")', if there are process groups with I/O requests waiting for
completion, then BFQ tags the scenario as 'asymmetric'. This detection
is needed for preserving service guarantees (for details, see comments
on the computation * of the variable asymmetric_scenario in the
function bfq_better_to_idle).
Unfortunately, commit '2d29c9f89fcd ("block, bfq: improve asymmetric
scenarios detection")' contains an error exactly in the updating of
the number of groups with I/O requests waiting for completion: if a
group has more than one descendant process, then the above number of
groups, which is renamed from num_active_groups to a more appropriate
num_groups_with_pending_reqs by this commit, may happen to be wrongly
decremented multiple times, namely every time one of the descendant
processes gets all its pending I/O requests completed.
A correct, complete solution should work as follows. Consider a group
that is inactive, i.e., that has no descendant process with pending
I/O inside BFQ queues. Then suppose that num_groups_with_pending_reqs
is still accounting for this group, because the group still has some
descendant process with some I/O request still in
flight. num_groups_with_pending_reqs should be decremented when the
in-flight request of the last descendant process is finally completed
(assuming that nothing else has changed for the group in the meantime,
in terms of composition of the group and active/inactive state of
child groups and processes). To accomplish this, an additional
pending-request counter must be added to entities, and must be
updated correctly.
To avoid this additional field and operations, this commit resorts to
the following tradeoff between simplicity and accuracy: for an
inactive group that is still counted in num_groups_with_pending_reqs,
this commit decrements num_groups_with_pending_reqs when the first
descendant process of the group remains with no request waiting for
completion.
This simplified scheme provides a fix to the unbalanced decrements
introduced by 2d29c9f89fcd. Since this error was also caused by lack
of comments on this non-trivial issue, this commit also adds related
comments.
Nic Soudée [Thu, 6 Dec 2018 16:59:25 +0000 (11:59 -0500)]
HID: quirks: fix RetroUSB.com devices
SNES RetroPort and RetroPad register only 4 gamepad buttons
when they should register all 8 buttons. This is described here:
https://ask.fedoraproject.org/en/question/128102
This is happening because of:
Commit 190d7f02ce8e ("HID: input: do not increment usages when
duplicate is found")
Here, I add the quirk HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE
(created for backward compatibility with the change in 190d7f02ce8e)
for the two products.
Fix an off-by-one error in the memory resource range. This resource is
used to determine the address range of the memory to be hot-plugged as
ZONE_DEVICE memory. The current end address results in the kernel
attempting to map an additional memblock and the hypervisor may reject
the mapping resulting in the entire hot-plug failing.
Fixes: b5beae5e224f ("powerpc/pseries: Add driver for PAPR SCM regions") Signed-off-by: Oliver O'Halloran <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
Making PAPR_SCM select LIBNVDIMM results in circular dependencies in
Kconfig when another symbol depends on it. Fix this by replacing the
select with a depends.
Fixes: b5beae5e224f ("powerpc/pseries: Add driver for PAPR SCM regions") Reported-by: Alastair D'Silva <[email protected]> Signed-off-by: Oliver O'Halloran <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
Sandipan Das [Thu, 6 Dec 2018 09:27:01 +0000 (14:57 +0530)]
powerpc/bpf: Fix broken uapi for BPF_PROG_TYPE_PERF_EVENT
Now that there are different variants of pt_regs for userspace and
kernel, the uapi for the BPF_PROG_TYPE_PERF_EVENT program type must be
changed by exporting the user_pt_regs structure instead of the pt_regs
structure that is in-kernel only.
Fixes: 002af9391bfb ("powerpc: Split user/kernel definitions of struct pt_regs") Signed-off-by: Sandipan Das <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
Kailang Yang [Fri, 7 Dec 2018 07:14:59 +0000 (15:14 +0800)]
ALSA: hda/realtek - Fixed headphone issue for ALC700
If it plugged headphone or headset into the jack, then
do the reboot, it will have a chance to cause headphone no sound.
It just need to run the headphone mode procedure after boot time.
The issue will be fixed.
It also suitable for ALC234 ALC274 and ALC294.
Linus Torvalds [Fri, 7 Dec 2018 03:35:50 +0000 (19:35 -0800)]
Merge tag 'drm-fixes-2018-12-07' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"There's a bit more in here than I'd like, and I'm hoping things calm
down when I'm out.
msm:
- a bunch of display fixes for the new DPU
- a couple of command submission fixes
omap:
- some DSI fixes
ast:
- driver unload crash fix
core:
- fix the lease uevent so userspace can distinguish it
amd:
- fix a bpc regression
- fix lru handling regression
- fixed firmware support for new GPUs
- power management fixes for vega20"
* tag 'drm-fixes-2018-12-07' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/ast: Fix connector leak during driver unload
drm/amdgpu/vcn: Update vcn.cur_state during suspend
drm/amd/display: Fix overflow/truncation from strncpy.
drm/amd/powerplay: improve OD code robustness
drm/amdgpu: enlarge maximum waiting time of KIQ
drm/fb-helper: Fix typo in parameter description
drm/amd/powerplay: support SoftMin/Max setting for some specific DPM
drm/amd/powerplay: issue pre-display settings for display change event
drm/amd/powerplay: support new pptable upload on Vega20
drm/amdgpu/gmc8: always load MC firmware in the driver
drm/amdgpu/gmc8: update MC firmware for polaris
drm/amdgpu: update mc firmware image for polaris12 variants
drm/msm: Fix error return checking
drm/msm/dpu: Ignore alpha for XBGR8888 format
drm/msm: dpu: Fix "WARNING: invalid free of devm_ allocated data"
drm/msm/hdmi: Drop pointless static qualifier in msm_hdmi_bind()
drm/msm: Move fence put to where failure occurs
drm/msm: dpu: Don't set legacy plane->crtc pointer
drm/msm/gpu: Don't map command buffers with nr_relocs equal to 0
drm/msm/hdmi: Enable HPD after HDMI IRQ is set up
...
Linus Torvalds [Fri, 7 Dec 2018 02:57:04 +0000 (18:57 -0800)]
Merge tag 'nfs-for-4.20-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"This is mainly fallout from the updates to the SUNRPC code that is
being triggered from less common combinations of NFS mount options.
Highlights include:
Stable fixes:
- Fix a page leak when using RPCSEC_GSS/krb5p to encrypt data.
Bugfixes:
- Fix a regression that causes the RPC receive code to hang
- Fix call_connect_status() so that it handles tasks that got
transmitted while queued waiting for the socket lock.
- Fix a memory leak in call_encode()
- Fix several other connect races.
- Fix receive code error handling.
- Use the discard iterator rather than MSG_TRUNC for compatibility
with AF_UNIX/AF_LOCAL sockets.
- nfs: don't dirty kernel pages read by direct-io
- pnfs/Flexfiles fix to enforce per-mirror stateid only for NFSv4
data servers"
* tag 'nfs-for-4.20-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Don't force a redundant disconnection in xs_read_stream()
SUNRPC: Fix up socket polling
SUNRPC: Use the discard iterator rather than MSG_TRUNC
SUNRPC: Treat EFAULT as a truncated message in xs_read_stream_request()
SUNRPC: Fix up handling of the XDRBUF_SPARSE_PAGES flag
SUNRPC: Fix RPC receive hangs
SUNRPC: Fix a potential race in xprt_connect()
SUNRPC: Fix a memory leak in call_encode()
SUNRPC: Fix leak of krb5p encode pages
SUNRPC: call_connect_status() must handle tasks that got transmitted
nfs: don't dirty kernel pages read by direct-io
flexfiles: enforce per-mirror stateid only for v4 DSes
Linus Torvalds [Fri, 7 Dec 2018 00:45:36 +0000 (16:45 -0800)]
Merge branch 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM spectre fix from Russell King:
"Exynos folk noticed that CPU hotplug wasn't working with their kernel
configuration, and have tested this as fixing the problem"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: ensure that processor vtables is not lost after boot
Masahiro Yamada [Thu, 6 Dec 2018 03:55:26 +0000 (12:55 +0900)]
i2c: uniphier-f: fill TX-FIFO only in IRQ handler for repeated START
- For a repeated START condition, this controller starts data transfer
immediately after the slave address is written to the TX-FIFO.
- Once the TX-FIFO empty interrupt is asserted, the controller makes
a pause even if additional data are written to the TX-FIFO.
Given those circumstances, the data after a repeated START may not be
transferred if the interrupt is asserted while the TX-FIFO is being
filled up. A more reliable way is to append TX data only in the
interrupt handler.
Masahiro Yamada [Thu, 6 Dec 2018 03:55:25 +0000 (12:55 +0900)]
i2c: uniphier-f: fix timeout error after reading 8 bytes
I was totally screwed up in commit eaba68785c2d ("i2c: uniphier-f:
fix race condition when IRQ is cleared"). Since that commit, if the
number of read bytes is multiple of the FIFO size (8, 16, 24... bytes),
the STOP condition could be issued twice, depending on the timing.
If this happens, the controller will go wrong, resulting in the timeout
error.
It was more than 3 years ago when I wrote this driver, so my memory
about this hardware was vague. Please let me correct the description
in the commit log of eaba68785c2d.
Clearing the IRQ status on exiting the IRQ handler is absolutely
fine. This controller makes a pause while any IRQ status is asserted.
If the IRQ status is cleared first, the hardware may start the next
transaction before the IRQ handler finishes what it supposed to do.
This partially reverts the bad commit with clear comments so that I
will never repeat this mistake.
I also investigated what is happening at the last moment of the read
mode. The UNIPHIER_FI2C_INT_RF interrupt is asserted a bit earlier
(by half a period of the clock cycle) than UNIPHIER_FI2C_INT_RB.
I consulted a hardware engineer, and I got the following information:
UNIPHIER_FI2C_INT_RF
asserted at the falling edge of SCL at the 8th bit.
UNIPHIER_FI2C_INT_RB
asserted at the rising edge of SCL at the 9th (ACK) bit.
In order to avoid calling uniphier_fi2c_stop() twice, check the latter
interrupt. I also commented this because it is obscure hardware internal.
Fixes: eaba68785c2d ("i2c: uniphier-f: fix race condition when IRQ is cleared") Signed-off-by: Masahiro Yamada <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
Hans de Goede [Wed, 21 Nov 2018 09:19:55 +0000 (10:19 +0100)]
i2c: scmi: Fix probe error on devices with an empty SMB0001 ACPI device node
Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.
This leads to the following error in dmesg:
[ 5.222731] cmi: probe of SMB0001:00 failed with error -5
This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.
The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.
The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.
To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
David S. Miller [Thu, 6 Dec 2018 21:31:09 +0000 (13:31 -0800)]
Merge branch 'mlxsw-Various-fixes'
Ido Schimmel says:
====================
mlxsw: Various fixes
Patches #1 and #2 fix two VxLAN related issues. The first patch removes
warnings that can currently be triggered from user space. Second patch
avoids leaking a FID in an error path.
Patch #3 fixes a too strict check that causes certain host routes not to
be promoted to perform GRE decapsulation in hardware.
Last patch avoids a use-after-free when deleting a VLAN device via an
ioctl when it is enslaved to a bridge. I have a patchset for net-next
that reworks this code and makes the driver more robust.
====================
Ido Schimmel [Thu, 6 Dec 2018 17:44:53 +0000 (17:44 +0000)]
mlxsw: spectrum_switchdev: Fix VLAN device deletion via ioctl
When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.
The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.
Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Petr Machata <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Nir Dotan [Thu, 6 Dec 2018 17:44:52 +0000 (17:44 +0000)]
mlxsw: spectrum_router: Relax GRE decap matching check
GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.
Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.
Fixes: 4607f6d26950 ("mlxsw: spectrum_router: Support IPv4 underlay decap") Signed-off-by: Nir Dotan <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().
Drop the reference when this unlikely error is hit.
Fixes: 1c30d1836aeb ("mlxsw: spectrum: Enable VxLAN enslavement to bridges") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Jiri Pirko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.
Fix by removing these warnings for now.
Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.
Fixes: 6e6030bd5412 ("mlxsw: spectrum_nve: Implement common NVE core") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Petr Machata <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Stefan Hajnoczi [Mon, 5 Nov 2018 10:35:47 +0000 (10:35 +0000)]
vhost/vsock: fix use-after-free in network stack callers
If the network stack calls .send_pkt()/.cancel_pkt() during .release(),
a struct vhost_vsock use-after-free is possible. This occurs because
.release() does not wait for other CPUs to stop using struct
vhost_vsock.
Switch to an RCU-enabled hashtable (indexed by guest CID) so that
.release() can wait for other CPUs by calling synchronize_rcu(). This
also eliminates vhost_vsock_lock acquisition in the data path so it
could have a positive effect on performance.
This is CVE-2018-14625 "kernel: use-after-free Read in vhost_transport_send_pkt".
Halil Pasic [Wed, 26 Sep 2018 16:48:30 +0000 (18:48 +0200)]
virtio/s390: fix race in ccw_io_helper()
While ccw_io_helper() seems like intended to be exclusive in a sense that
it is supposed to facilitate I/O for at most one thread at any given
time, there is actually nothing ensuring that threads won't pile up at
vcdev->wait_q. If they do, all threads get woken up and see the status
that belongs to some other request than their own. This can lead to bugs.
For an example see:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1788432
This race normally does not cause any problems. The operations provided
by struct virtio_config_ops are usually invoked in a well defined
sequence, normally don't fail, and are normally used quite infrequent
too.
Yet, if some of the these operations are directly triggered via sysfs
attributes, like in the case described by the referenced bug, userspace
is given an opportunity to force races by increasing the frequency of the
given operations.
Let us fix the problem by ensuring, that for each device, we finish
processing the previous request before starting with a new one.
Halil Pasic [Wed, 26 Sep 2018 16:48:29 +0000 (18:48 +0200)]
virtio/s390: avoid race on vcdev->config
Currently we have a race on vcdev->config in virtio_ccw_get_config() and
in virtio_ccw_set_config().
This normally does not cause problems, as these are usually infrequent
operations. However, for some devices writing to/reading from the config
space can be triggered through sysfs attributes. For these, userspace can
force the race by increasing the frequency.
Stefan Hajnoczi [Thu, 6 Dec 2018 19:14:34 +0000 (19:14 +0000)]
vhost/vsock: fix reset orphans race with close timeout
If a local process has closed a connected socket and hasn't received a
RST packet yet, then the socket remains in the table until a timeout
expires.
When a vhost_vsock instance is released with the timeout still pending,
the socket is never freed because vhost_vsock has already set the
SOCK_DONE flag.
Check if the close timer is pending and let it close the socket. This
prevents the race which can leak sockets.
Linus Torvalds [Thu, 6 Dec 2018 17:25:53 +0000 (09:25 -0800)]
Merge tag 'sound-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Still more incoming fixes than wished at this stage, but all look like
small and reasonable fixes.
In addition to the usual HD-audio and USB-audio quirks for various
devices, two notable changes are included:
- a fix for USB-audio UAF at probing a malformed descriptor
- workarounds for PCM rwsem mutex starvation"
* tag 'sound-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4860G/Z6860G
ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4660G
ALSA: hda/realtek - Add support for Acer Aspire C24-860 headset mic
ALSA: hda/realtek: ALC286 mic and headset-mode fixups for Acer Aspire U27-880
ALSA: usb-audio: Fix UAF decrement if card has no live interfaces in card.c
ALSA: hda/realtek - Fix speaker output regression on Thinkpad T570
ALSA: pcm: Fix interval evaluation with openmin/max
ALSA: hda: Add support for AMD Stoney Ridge
ALSA: usb-audio: Add SMSL D1 to quirks for native DSD support
ALSA: pcm: Fix starvation on down_write_nonblock()
ALSA: pcm: Call snd_pcm_unlink() conditionally at closing
Alexander Popov [Thu, 6 Dec 2018 15:13:07 +0000 (18:13 +0300)]
stackleak: Register the 'stackleak_cleanup' pass before the '*free_cfg' pass
Currently the 'stackleak_cleanup' pass deleting a CALL insn is executed
after the 'reload' pass. That allows gcc to do some weird optimization in
function prologues and epilogues, which are generated later [1].
Let's avoid that by registering the 'stackleak_cleanup' pass before
the '*free_cfg' pass. It's the moment when the stack frame size is
already final, function prologues and epilogues are generated, and the
machine-dependent code transformations are not done.
Russell King [Thu, 6 Dec 2018 16:36:38 +0000 (16:36 +0000)]
ARM: ensure that processor vtables is not lost after boot
Marek Szyprowski reported problems with CPU hotplug in current kernels.
This was tracked down to the processor vtables being located in an
init section, and therefore discarded after kernel boot, despite being
required after boot to properly initialise the non-boot CPUs.
Arrange for these tables to end up in .rodata when required.
Reported-by: Marek Szyprowski <[email protected]> Tested-by: Krzysztof Kozlowski <[email protected]> Fixes: 383fb3ee8024 ("ARM: spectre-v2: per-CPU vtables to work around big.Little systems") Signed-off-by: Russell King <[email protected]>
The broken macros make the glibc compile error. If there is no
__NR3264_fstat*, we should also removed related definitions.
Reported-by: Marcin Juszkiewicz <[email protected]> Fixes: bf4b6a7d371e ("y2038: Remove stat64 family from default syscall set")
[arnd: Both Marcin and Guo provided this patch to fix up my clearly
broken commit, I applied the version with the better changelog.] Signed-off-by: Guo Ren <[email protected]> Signed-off-by: Mao Han <[email protected]> Cc: Arnd Bergmann <[email protected]> Signed-off-by: Arnd Bergmann <[email protected]>
These interrupt functions are already non-attachable by kprobes.
Blacklist them explicitly so that they can show up in
/sys/kernel/debug/kprobes/blacklist and tools like BCC can use this
additional information.
Macpaul Lin [Wed, 17 Oct 2018 15:08:38 +0000 (23:08 +0800)]
kgdboc: fix KASAN global-out-of-bounds bug in param_set_kgdboc_var()
This patch is trying to fix KE issue due to
"BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198"
reported by Syzkaller scan."
[26364:syz-executor0][name:report8t]BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198
[26364:syz-executor0][name:report&]Read of size 1 at addr ffffff900e44f95f by task syz-executor0/26364
[26364:syz-executor0][name:report&]
[26364:syz-executor0]CPU: 7 PID: 26364 Comm: syz-executor0 Tainted: G W 0
[26364:syz-executor0]Call trace:
[26364:syz-executor0][<ffffff9008095cf8>] dump_bacIctrace+Ox0/0x470
[26364:syz-executor0][<ffffff9008096de0>] show_stack+0x20/0x30
[26364:syz-executor0][<ffffff90089cc9c8>] dump_stack+Oxd8/0x128
[26364:syz-executor0][<ffffff90084edb38>] print_address_description +0x80/0x4a8
[26364:syz-executor0][<ffffff90084ee270>] kasan_report+Ox178/0x390
[26364:syz-executor0][<ffffff90084ee4a0>] _asan_report_loadi_noabort+Ox18/0x20
[26364:syz-executor0][<ffffff9008b092ac>] param_set_kgdboc_var+Ox194/0x198
[26364:syz-executor0][<ffffff900813af64>] param_attr_store+Ox14c/0x270
[26364:syz-executor0][<ffffff90081394c8>] module_attr_store+0x60/0x90
[26364:syz-executor0][<ffffff90086690c0>] sysfs_kl_write+Ox100/0x158
[26364:syz-executor0][<ffffff9008666d84>] kernfs_fop_write+0x27c/0x3a8
[26364:syz-executor0][<ffffff9008508264>] do_loop_readv_writev+0x114/0x1b0
[26364:syz-executor0][<ffffff9008509ac8>] do_readv_writev+0x4f8/0x5e0
[26364:syz-executor0][<ffffff9008509ce4>] vfs_writev+0x7c/Oxb8
[26364:syz-executor0][<ffffff900850ba64>] SyS_writev+Oxcc/0x208
[26364:syz-executor0][<ffffff90080883f0>] elO_svc_naked +0x24/0x28
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]The buggy address belongs to the variable:
[26364:syz-executor0][name:report&] kgdb_tty_line+Ox3f/0x40
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]Memory state around the buggy address:
[26364:syz-executor0] ffffff900e44f800: 00 00 00 00 00 04 fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0] ffffff900e44f880: fa fa fa fa 00 fa fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0]> ffffff900e44f900: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
[26364:syz-executor0][name:report&] ^
[26364:syz-executor0] ffffff900e44f980: 00 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
[26364:syz-executor0] ffffff900e44fa00: 04 fa fa fa fa fa fa fa 00 fa fa fa fa fa fa fa
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:panic&]Disabling lock debugging due to kernel taint
[26364:syz-executor0]------------[cut here]------------
After checking the source code, we've found there might be an out-of-bounds
access to "config[len - 1]" array when the variable "len" is zero.
Matthew Wilcox [Mon, 5 Nov 2018 18:19:54 +0000 (13:19 -0500)]
XArray tests: Handle larger indices more elegantly
xa_mk_value() only handles values up to LONG_MAX. I successfully hid
that inside xa_store_index() and xa_erase_index(), but it turned out I
also needed it for testing xa_alloc() on 32-bit machines. So extract
xa_mk_index() from the above two functions, and convert the non-constant
users of xa_mk_value() to xa_mk_index().
Matthew Wilcox [Mon, 26 Nov 2018 21:08:43 +0000 (16:08 -0500)]
XArray: Add xa_cmpxchg_irq and xa_cmpxchg_bh
These convenience wrappers match the other _irq and _bh wrappers we
already have. It turns out I'd already open-coded xa_cmpxchg_irq()
in the shmem code, so convert that.
Matthew Wilcox [Thu, 6 Dec 2018 13:19:13 +0000 (08:19 -0500)]
radix tree: Don't return retry entries from lookup
Commit 66ee620f06f9 ("idr: Permit any valid kernel pointer to be stored")
changed the radix tree lookup so that it stops when reaching the bottom
of the tree. However, the condition was added in the wrong place,
making it possible to return retry entries to the caller. Reorder the
tests to check for the retry entry before checking whether we're at the
bottom of the tree. The retry entry should never be found in the tree
root, so it's safe to defer the check until the end of the loop.
Add a regression test to the test-suite to be sure this doesn't come
back.
Fixes: 66ee620f06f9 ("idr: Permit any valid kernel pointer to be stored") Reported-by: Greg Kurz <[email protected]> Signed-off-by: Matthew Wilcox <[email protected]>
Mathias Nyman [Wed, 5 Dec 2018 12:22:39 +0000 (14:22 +0200)]
xhci: Prevent U1/U2 link pm states if exit latency is too long
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Sandeep Singh [Wed, 5 Dec 2018 12:22:38 +0000 (14:22 +0200)]
xhci: workaround CSS timeout on AMD SNPS 3.0 xHC
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
After checking the sdhci code, we found the timeout check actually has a
little window that the CPU can be scheduled out and when it comes back,
the original time set or check is not valid.
In commit 5e9dcb6188a4 ("powerpc/boot: Expose Kconfig symbols to
wrapper") we added a dependency to serial.c on autoconf.h:
$(obj)/serial.c: $(obj)/autoconf.h
This works when building in-tree (ie. with KBUILD_OUTPUT unset)
because the obj tree is the src tree.
But when building with eg. O=build and -j 1 the build fails:
gcc ... -I../arch/powerpc/boot -c -o arch/powerpc/boot/serial.o arch/powerpc/boot/serial.c
gcc: error: arch/powerpc/boot/serial.c: No such file or directory
Why this is only happening with -j 1 is not clear, when building with
-j greater than 1 somehow we decide to look for serial.c in the src
tree (../), eg:
Regardless we shouldn't be specifying a dependency on serial.c in the
build tree, we want to add a dependency to the version in $(srctree)
so fix the rule to say that.
Fixes: 5e9dcb6188a4 ("powerpc/boot: Expose Kconfig symbols to wrapper") Tested-by: Daniel Axtens <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
Jiri Wiesner [Wed, 5 Dec 2018 15:55:29 +0000 (16:55 +0100)]
ipv4: ipv6: netfilter: Adjust the frag mem limit when truesize changes
The *_frag_reasm() functions are susceptible to miscalculating the byte
count of packet fragments in case the truesize of a head buffer changes.
The truesize member may be changed by the call to skb_unclone(), leaving
the fragment memory limit counter unbalanced even if all fragments are
processed. This miscalculation goes unnoticed as long as the network
namespace which holds the counter is not destroyed.
Should an attempt be made to destroy a network namespace that holds an
unbalanced fragment memory limit counter the cleanup of the namespace
never finishes. The thread handling the cleanup gets stuck in
inet_frags_exit_net() waiting for the percpu counter to reach zero. The
thread is usually in running state with a stacktrace similar to:
It is not possible to create new network namespaces, and processes
that call unshare() end up being stuck in uninterruptible sleep state
waiting to acquire the net_mutex.
The bug was observed in the IPv6 netfilter code by Per Sundstrom.
I thank him for his analysis of the problem. The parts of this patch
that apply to IPv4 and IPv6 fragment reassembly are preemptive measures.
If for some reason an association's fragmentation point is zero,
sctp_datamsg_from_user will try to endlessly try to divide a message
into zero-sized chunks. This eventually causes kernel panic due to
running out of memory.
Although this situation is quite unlikely, it has occurred before as
reported. I propose to add this simple last-ditch sanity check due to
the severity of the potential consequences.
Sam Bobroff [Mon, 3 Dec 2018 00:53:21 +0000 (11:53 +1100)]
drm/ast: Fix connector leak during driver unload
When unloading the ast driver, a warning message is printed by
drm_mode_config_cleanup() because a reference is still held to one of
the drm_connector structs.
Correct this by calling drm_crtc_force_disable_all() in
ast_fbdev_destroy().
Dave Airlie [Thu, 6 Dec 2018 04:08:43 +0000 (14:08 +1000)]
Merge branch 'drm-fixes-4.20' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.20:
- Fix banding regression on 6 bpc panels
- Vega20 fix for six 4k displays
- Fix LRU handling in ttm_buffer_object_transfer
- Use proper MC firmware for newer polaris variants
- Vega20 powerplay fixes
- VCN suspend/resume fix for PCO
- Misc other fixes
Dave Airlie [Thu, 6 Dec 2018 04:07:26 +0000 (14:07 +1000)]
Merge tag 'msm-fixes-2018-12-04' of https://gitlab.freedesktop.org/seanpaul/dpu-staging into drm-fixes
- Several related to incorrect error checking/handling (Various)
- Prevent IRQ storm on MDP5 HDMI hotplug (Todor)
- Don't capture crash state if unsupported (Sharat)
- Properly grab vblank reference in atomic wait for commit done (Sean)
put_uprobe() is calling delayed_uprobe_remove() without taking
delayed_uprobe_lock and thus the race sometimes results in a
kernel crash. Fix this by taking delayed_uprobe_lock before
calling delayed_uprobe_remove() from put_uprobe().
Anders Roxell [Fri, 30 Nov 2018 15:08:59 +0000 (16:08 +0100)]
stackleak: Mark stackleak_track_stack() as notrace
Function graph tracing recurses into itself when stackleak is enabled,
causing the ftrace graph selftest to run for up to 90 seconds and
trigger the softlockup watchdog.
Breakpoint 2, ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:200
200 mcount_get_lr_addr x0 // pointer to function's saved lr
(gdb) bt
\#0 ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:200
\#1 0xffffff80081d5280 in ftrace_caller () at ../arch/arm64/kernel/entry-ftrace.S:153
\#2 0xffffff8008555484 in stackleak_track_stack () at ../kernel/stackleak.c:106
\#3 0xffffff8008421ff8 in ftrace_ops_test (ops=0xffffff8009eaa840 <graph_ops>, ip=18446743524091297036, regs=<optimized out>) at ../kernel/trace/ftrace.c:1507
\#4 0xffffff8008428770 in __ftrace_ops_list_func (regs=<optimized out>, ignored=<optimized out>, parent_ip=<optimized out>, ip=<optimized out>) at ../kernel/trace/ftrace.c:6286
\#5 ftrace_ops_no_ops (ip=18446743524091297036, parent_ip=18446743524091242824) at ../kernel/trace/ftrace.c:6321
\#6 0xffffff80081d5280 in ftrace_caller () at ../arch/arm64/kernel/entry-ftrace.S:153
\#7 0xffffff800832fd10 in irq_find_mapping (domain=0xffffffc03fc4bc80, hwirq=27) at ../kernel/irq/irqdomain.c:876
\#8 0xffffff800832294c in __handle_domain_irq (domain=0xffffffc03fc4bc80, hwirq=27, lookup=true, regs=0xffffff800814b840) at ../kernel/irq/irqdesc.c:650
\#9 0xffffff80081d52b4 in ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:205
Rework so we mark stackleak_track_stack as notrace
Anson Huang [Tue, 4 Dec 2018 03:17:45 +0000 (03:17 +0000)]
ARM: imx: update the cpu power up timing setting on i.mx6sx
The sw2iso count should cover ARM LDO ramp-up time,
the MAX ARM LDO ramp-up time may be up to more than
100us on some boards, this patch sets sw2iso to 0xf
(~384us) which is the reset value, and it is much
more safe to cover different boards, since we have
observed that some customer boards failed with current
setting of 0x2.
Fixes: 05136f0897b5 ("ARM: imx: support arm power off in cpuidle for i.mx6sx") Signed-off-by: Anson Huang <[email protected]> Reviewed-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
Linus Torvalds [Thu, 6 Dec 2018 01:06:31 +0000 (17:06 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four obvious bug fixes. The vmw_pscsi is so old that it's amazing
no-one noticed before now"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: storvsc: Fix a race in sub-channel creation that can cause panic
scsi: vmw_pscsi: Rearrange code to avoid multiple calls to free_irq during unload
scsi: libiscsi: Fix NULL pointer dereference in iscsi_eh_session_reset
scsi: lpfc: fix block guard enablement on SLI3 adapters
Yuchung Cheng [Wed, 5 Dec 2018 22:38:38 +0000 (14:38 -0800)]
tcp: fix NULL ref in tail loss probe
TCP loss probe timer may fire when the retranmission queue is empty but
has a non-zero tp->packets_out counter. tcp_send_loss_probe will call
tcp_rearm_rto which triggers NULL pointer reference by fetching the
retranmission queue head in its sub-routines.
Add a more detailed warning to help catch the root cause of the inflight
accounting inconsistency.
Eric Dumazet [Wed, 5 Dec 2018 22:24:31 +0000 (14:24 -0800)]
tcp: Do not underestimate rwnd_limited
If available rwnd is too small, tcp_tso_should_defer()
can decide it is worth waiting before splitting a TSO packet.
This really means we are rwnd limited.
Fixes: 5615f88614a4 ("tcp: instrument how long TCP is limited by receive window") Signed-off-by: Eric Dumazet <[email protected]> Acked-by: Soheil Hassas Yeganeh <[email protected]> Reviewed-by: Yuchung Cheng <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Edward Cree [Tue, 4 Dec 2018 17:37:57 +0000 (17:37 +0000)]
net: use skb_list_del_init() to remove from RX sublists
list_del() leaves the skb->next pointer poisoned, which can then lead to
a crash in e.g. OVS forwarding. For example, setting up an OVS VXLAN
forwarding bridge on sfc as per:
Fixes: 9af86f933894 ("net: core: fix use-after-free in __netif_receive_skb_list_core") Fixes: 7da517a3bc52 ("net: core: Another step of skb receive list processing") Fixes: a4ca8b7df73c ("net: ipv4: fix drop handling in ip_list_rcv() and ip_list_rcv_finish()") Fixes: d8269e2cbf90 ("net: ipv6: listify ipv6_rcv() and ip6_rcv_finish()") Signed-off-by: Edward Cree <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Wed, 5 Dec 2018 23:51:41 +0000 (15:51 -0800)]
Merge tag 'arc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes/updates from Vineet Gupta
- Missing reads{x}()/writes{x}() getting in the way of some drivers [Jose Abreu]
- Builds defaulting to ARCv2 ISA based configsa [Kevin Hilman]
- Misc fixes
* tag 'arc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: io.h: Implement reads{x}()/writes{x}()
ARC: change defconfig defaults to ARCv2
arc: [devboards] Add support of NFSv3 ACL
ARC: mm: fix uninitialised signal code in do_page_fault
ARC: [plat-hsdk] Enable DW APB GPIO support
ARCv2: boot log unaligned access in use
ARC: IOC: panic if kernel was started with previously enabled IOC
ARC: remove redundant 'default n' from Kconfig
David Rientjes [Wed, 5 Dec 2018 23:45:54 +0000 (15:45 -0800)]
mm, thp: restore node-local hugepage allocations
This is a full revert of ac5b2c18911f ("mm: thp: relax __GFP_THISNODE for
MADV_HUGEPAGE mappings") and a partial revert of 89c83fb539f9 ("mm, thp:
consolidate THP gfp handling into alloc_hugepage_direct_gfpmask").
By not setting __GFP_THISNODE, applications can allocate remote hugepages
when the local node is fragmented or low on memory when either the thp
defrag setting is "always" or the vma has been madvised with
MADV_HUGEPAGE.
Remote access to hugepages often has much higher latency than local pages
of the native page size. On Haswell, ac5b2c18911f was shown to have a
13.9% access regression after this commit for binaries that remap their
text segment to be backed by transparent hugepages.
The intent of ac5b2c18911f is to address an issue where a local node is
low on memory or fragmented such that a hugepage cannot be allocated. In
every scenario where this was described as a fix, there is abundant and
unfragmented remote memory available to allocate from, even with a greater
access latency.
If remote memory is also low or fragmented, not setting __GFP_THISNODE was
also measured on Haswell to have a 40% regression in allocation latency.
Dan Williams [Mon, 3 Dec 2018 18:30:25 +0000 (10:30 -0800)]
acpi/nfit: Fix user-initiated ARS to be "ARS-long" rather than "ARS-short"
A "short" ARS (address range scrub) instructs the platform firmware to
return known errors. In contrast, a "long" ARS instructs platform
firmware to arrange every data address on the DIMM to be read / checked
for poisoned data.
The conversion of the flags in commit d3abaf43bab8 "acpi, nfit: Fix
Address Range Scrub completion tracking", changed the meaning of passing
'0' to acpi_nfit_ars_rescan(). Previously '0' meant "not short", now '0'
is ARS_REQ_SHORT. Pass ARS_REQ_LONG to restore the expected scrub-type
behavior of user-initiated ARS sessions.
Dan Williams [Sat, 24 Nov 2018 18:47:04 +0000 (10:47 -0800)]
libnvdimm, pfn: Pad pfn namespaces relative to other regions
Commit cfe30b872058 "libnvdimm, pmem: adjust for section collisions with
'System RAM'" enabled Linux to workaround occasions where platform
firmware arranges for "System RAM" and "Persistent Memory" to collide
within a single section boundary. Unfortunately, as reported in this
issue [1], platform firmware can inflict the same collision between
persistent memory regions.
The approach of interrogating iomem_resource does not work in this
case because platform firmware may merge multiple regions into a single
iomem_resource range. Instead provide a method to interrogate regions
that share the same parent bus.
This is a stop-gap until the core-MM can grow support for hotplug on
sub-section boundaries.
Dan Williams [Wed, 5 Dec 2018 22:11:48 +0000 (14:11 -0800)]
tools/testing/nvdimm: Align test resources to 128M
In preparation for libnvdimm growing new restrictions to detect section
conflicts between persistent memory regions, enable nfit_test to
allocate aligned resources. Use a gen_pool to allocate nfit_test's fake
resources in a separate address space from the virtual translation of
the same.
Linus Torvalds [Wed, 5 Dec 2018 21:28:01 +0000 (13:28 -0800)]
Merge tag 'for-linus-20181205' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A bit earlier in the week as usual, but there's a fix here that should
go in sooner rather than later.
Under a combination of circumstance, the direct issue path in blk-mq
could corrupt data. This wasn't easy to hit, but the ones that are
affected by it, seem to hit it pretty easily. Full explanation in the
patch. None of the regular filesystem and storage testing has
triggered it, even though it's been around since 4.19-rc1.
Outside of that, whitelist trim tweak for certain Samsung devices for
libata"
* tag 'for-linus-20181205' of git://git.kernel.dk/linux-block:
blk-mq: fix corruption with direct issue
libata: whitelist all SAMSUNG MZ7KM* solid-state disks
projects / linux.git / log