Evgeny Novikov [Sun, 22 Aug 2021 09:48:03 +0000 (11:48 +0200)]
media: dvb-frontends: mn88443x: Handle errors of clk_prepare_enable()
mn88443x_cmn_power_on() did not handle possible errors of
clk_prepare_enable() and always finished successfully so that its caller
mn88443x_probe() did not care about failed preparing/enabling of clocks
as well.
Add missed error handling in both mn88443x_cmn_power_on() and
mn88443x_probe(). This required to change the return value of the former
from "void" to "int".
Found by Linux Driver Verification project (linuxtesting.org).
media: rcar-isp: Add Renesas R-Car Image Signal Processor driver
Add a V4L2 driver for Renesas R-Car Image Signal Processor. The driver
supports the R-Car V3U SoC where the ISP IP sits between the R-Car CSI-2
receiver and VIN and filters the CSI-2 data based on VC/DT and directs
the video stream to different VIN IPs.
The only usage of imgu_subdev_internal_ops is to assign its address to
the internal_ops field in the v4l2_subdev struct, which is a pointer to
const v4l2_subdev_internal_ops. Make it const to allow the compiler to
put it in read-only memory.
Sakari Ailus [Fri, 20 Aug 2021 12:56:26 +0000 (14:56 +0200)]
media: admin-guide: Update i2c-cardlist
Add MIPI CCS compliant devices, a few Sony IMX, Hynix Hi-846 and
Omnivision ov13b10 sensors and the DW9768 lens driver to the list of
supported devices. Also drop SMIA since as a standard it is obsolete.
media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera
The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports
usual features like I2C control, CSI-2 for frame data, digital/analog
gain control or test patterns.
This driver supports the 640x480, 1280x720 and 1632x1224 resolution
modes. It supports runtime PM in order not to draw any unnecessary power.
The part is also called YACG4D0C9SHC and a datasheet can be found at
https://product.skhynix.com/products/cis/cis.go
The large sets of partly undocumented register values are for example
found when searching for the hi846_mipi_raw_Sensor.c Android driver.
Dikshita Agarwal [Tue, 10 Aug 2021 09:47:55 +0000 (11:47 +0200)]
media: venus: Set buffer to FW based on FW min count requirement.
- Get the min buffer count required by FW from source event change
and use the same value to decide actual buffer count and for
buffer size calculation.
- Setup DPB and OPB buffers after session continue incase of
reconfig.
Dikshita Agarwal [Tue, 10 Aug 2021 09:47:52 +0000 (11:47 +0200)]
media: venus: hfi: Skip AON register programming for V6 1pipe
AON register programming is used to set NOC to low power mode
during V6 power off sequence. However AON register memory map
is not applicable to 1pipe, hence skipping AON register programming.
media: venus: fix vpp frequency calculation for decoder
In existing video driver implementation vpp frequency calculation in
calculate_inst_freq() is always zero because the value of vpp_freq_per_mb
is always zero for decoder.
Fixed this by correcting the calculating the vpp frequency calculation for
decoder.
Fixes: 3cfe5815ce0e ("media: venus: Enable low power setting for encoder") Signed-off-by: Mansur Alisha Shaik <[email protected]> Signed-off-by: Stanimir Varbanov <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
media: venus: vdec: update output buffer size during vdec_s_fmt()
Video driver maintains an internal context for the output buffer size.
During S_fmt() on capture plane, the output buffer size is not updated
in driver context. As a result, during buf_prepare(), the size of the
vb2_plane and internal size of the buffer, as maintained by the driver,
does not match. This leads to buf_prepare() failure.
Update the instance context for the output buffer size during s_fmt().
media: venus: helper: change log level for false warning message
In current video driver implementation in calculate_inst_freq()
frequency is calculated based on filled_len. The filled_len may
vary frame to frame, because of this in load_scale_v4() since
frequency is calculated for all instances, driver is throwing
false warning like "HW is overloaded".
Hence to handle this, changed log level to low log message. Since the
actual session rejection is happening in decide_core() based on
load.
gcc notices that the driver mixes 'dma_addr_t' 'u8 *' and 'u32'
to store DMA addresses:
drivers/media/platform/omap/omap_vout.c: In function 'omap_vout_vb2_prepare':
drivers/media/platform/omap/omap_vout.c:979:37: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
vout->queued_buf_addr[vb->index] = (u8 *)buf_phy_addr;
^
drivers/media/platform/omap/omap_vout.c: In function 'omap_vout_create_video_devices':
drivers/media/platform/omap/omap_vout.c:1479:21: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
vout->fbuf.base = (void *)info.paddr;
Use dma_addr_t everywhere here to avoid the type conversions and document
what the address is used for. Assigning to vout->fbuf.base still requires
a cast, since that is part of the driver independent data structure.
Kieran Bingham [Fri, 18 Jun 2021 19:09:05 +0000 (21:09 +0200)]
media: vsp1: Simplify DRM UIF handling
In commit 6732f3139380 ("media: v4l: vsp1: Fix uif null pointer access")
the handling of the UIF was over complicated, and the patch applied
before review.
media: imx-jpeg: Remove soft reset between frames encoding
Remove soft reset between frames, which was merely a workaround,
actually replace it with something less aggressive: clearing of jpeg stream
buffer pointer, via STM_CTRL[BITBUF_PTR_CLR].
According to the reference manual, the BITBUF_PTR_CLR is performed on
context switch, but, per hardware team recommendation, it is also working
without context switch, which is the case for this driver, for now.
Without soft reset and without BITBUF_PTR_CLR, successive encoding jobs
continue from where the previous left off, basically writing past the
v4l2 buffer.
media: hantro: Auto generate the AXI ID to avoid conflicts
The AXI ID is an AXI bus configuration for improve bus performance.
If read and write operations use different IDs the operations can be
paralleled, whereas when they have the same ID the operations will be
serialized. Right now, the write ID is fixed to 0 but we can set it to
0xff to get auto generated IDs to avoid possible conflicts.
This change has no functional changes, but seems reasonable to let the
hardware to autogenerate the ID instead of hardcoding in software.
Randy Dunlap [Tue, 21 Sep 2021 22:10:40 +0000 (00:10 +0200)]
media: CEC: keep related menu entries together
Keep all of the CEC menu items grouped together.
By grouping all of these menu entries inside a menu/endmenu block,
they are forced to be kept together and they are displayed/presented
in a group for users.
Tested with xconfig, gconfig, menuconfig, and nconfig.
Fixes: 46d2a3b964dd ("media: place CEC menu before MEDIA_SUPPORT") Signed-off-by: Randy Dunlap <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
The only usage of vpu_m2m_ops is to pass its address to v4l2_m2m_init()
which has a pointer to const struct v4l2_m2m_ops as argument. Make it
const to allow the compiler to put it in read-only memory.
Colin Ian King [Fri, 17 Sep 2021 16:07:02 +0000 (18:07 +0200)]
media: em28xx: Don't use ops->suspend if it is NULL
The call to ops->suspend for the dev->dev_next case can currently
trigger a call on a null function pointer if ops->suspend is null.
Skip over the use of function ops->suspend if it is null.
Addresses-Coverity: ("Dereference after null check")
Fixes: be7fd3c3a8c5 ("media: em28xx: Hauppauge DualHD second tuner functionality") Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
media: rcar-csi2: Add checking to rcsi2_start_receiver()
If rcsi2_code_to_fmt() return NULL, then null pointer dereference occurs
in the next cycle. That should not be possible now but adding checking
protects from future bugs.
The patch adds checking if format is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
elf: don't use MAP_FIXED_NOREPLACE for elf interpreter mappings
In commit b212921b13bd ("elf: don't use MAP_FIXED_NOREPLACE for elf
executable mappings") we still leave MAP_FIXED_NOREPLACE in place for
load_elf_interp.
Unfortunately, this will cause kernel to fail to start with:
1 (init): Uhuuh, elf segment at 00003ffff7ffd000 requested but the memory is mapped already
Failed to execute /init (error -17)
The reason is that the elf interpreter (ld.so) has overlapping segments.
readelf -l ld-2.31.so
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000000000 0x0000000000000000 0x0000000000000000
0x000000000002c94c 0x000000000002c94c R E 0x10000
LOAD 0x000000000002dae0 0x000000000003dae0 0x000000000003dae0
0x00000000000021e8 0x0000000000002320 RW 0x10000
LOAD 0x000000000002fe00 0x000000000003fe00 0x000000000003fe00
0x00000000000011ac 0x0000000000001328 RW 0x10000
The reason for this problem is the same as described in commit ad55eac74f20 ("elf: enforce MAP_FIXED on overlaying elf segments").
Not only executable binaries, elf interpreters (e.g. ld.so) can have
overlapping elf segments, so we better drop MAP_FIXED_NOREPLACE and go
back to MAP_FIXED in load_elf_interp.
Linus Torvalds [Sun, 3 Oct 2021 20:56:53 +0000 (13:56 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix a number of ext4 bugs in fast_commit, inline data, and delayed
allocation.
Also fix error handling code paths in ext4_dx_readdir() and
ext4_fill_super().
Finally, avoid a grabbing a journal head in the delayed allocation
write in the common cases where we are overwriting a pre-existing
block or appending to an inode"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: recheck buffer uptodate bit under buffer lock
ext4: fix potential infinite loop in ext4_dx_readdir()
ext4: flush s_error_work before journal destroy in ext4_fill_super
ext4: fix loff_t overflow in ext4_max_bitmap_size()
ext4: fix reserved space counter leakage
ext4: limit the number of blocks in one ADD_RANGE TLV
ext4: enforce buffer head state assertion in ext4_da_map_blocks
ext4: remove extent cache entries when truncating inline data
ext4: drop unnecessary journal handle in delalloc write
ext4: factor out write end code of inline file
ext4: correct the error path of ext4_write_inline_data_end()
ext4: check and update i_disksize properly
ext4: add error checking to ext4_ext_replay_set_iblocks()
Linus Torvalds [Sun, 3 Oct 2021 20:45:48 +0000 (13:45 -0700)]
objtool: print out the symbol type when complaining about it
The objtool warning that the kvm instruction emulation code triggered
wasn't very useful:
arch/x86/kvm/emulate.o: warning: objtool: __ex_table+0x4: don't know how to handle reloc symbol type: kvm_fastop_exception
in that it helpfully tells you which symbol name it had trouble figuring
out the relocation for, but it doesn't actually say what the unknown
symbol type was that triggered it all.
In this case it was because of missing type information (type 0, aka
STT_NOTYPE), but on the whole it really should just have printed that
out as part of the message.
Because if this warning triggers, that's very much the first thing you
want to know - why did reloc2sec_off() return failure for that symbol?
So rather than just saying you can't handle some type of symbol without
saying what the type _was_, just print out the type number too.
Linus Torvalds [Sun, 3 Oct 2021 20:34:19 +0000 (13:34 -0700)]
kvm: fix objtool relocation warning
The recent change to make objtool aware of more symbol relocation types
(commit 24ff65257375: "objtool: Teach get_alt_entry() about more
relocation types") also added another check, and resulted in this
objtool warning when building kvm on x86:
arch/x86/kvm/emulate.o: warning: objtool: __ex_table+0x4: don't know how to handle reloc symbol type: kvm_fastop_exception
The reason seems to be that kvm_fastop_exception() is marked as a global
symbol, which causes the relocation to ke kept around for objtool. And
at the same time, the kvm_fastop_exception definition (which is done as
an inline asm statement) doesn't actually set the type of the global,
which then makes objtool unhappy.
The minimal fix is to just not mark kvm_fastop_exception as being a
global symbol. It's only used in that one compilation unit anyway, so
it was always pointless. That's how all the other local exception table
labels are done.
I'm not entirely happy about the kinds of games that the kvm code plays
with doing its own exception handling, and the fact that it confused
objtool is most definitely a symptom of the code being a bit too subtle
and ad-hoc. But at least this trivial one-liner makes objtool no longer
upset about what is going on.
Linus Torvalds [Sun, 3 Oct 2021 18:10:09 +0000 (11:10 -0700)]
Merge tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core and kernfs fixes for reported issues for
5.15-rc4. These fixes include:
- kernfs positive dentry bugfix
- debugfs_create_file_size error path fix
- cpumask sysfs file bugfix to preserve the user/kernel abi (has been
reported multiple times.)
- devlink fixes for mdiobus devices as reported by the subsystem
maintainers.
Also included in here are some devlink debugging changes to make it
easier for people to report problems when asked. They have already
helped with the mdiobus and other subsystems reporting issues.
All of these have been linux-next for a while with no reported issues"
* tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: also call kernfs_set_rev() for positive dentry
driver core: Add debug logs when fwnode links are added/deleted
driver core: Create __fwnode_link_del() helper function
driver core: Set deferred probe reason when deferred by driver core
net: mdiobus: Set FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD for mdiobus parents
driver core: fw_devlink: Add support for FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD
driver core: fw_devlink: Improve handling of cyclic dependencies
cpumask: Omit terminating null byte in cpumap_print_{list,bitmask}_to_buf
debugfs: debugfs_create_file_size(): use IS_ERR to check for error
Linus Torvalds [Sun, 3 Oct 2021 17:32:27 +0000 (10:32 -0700)]
Merge tag 'perf_urgent_for_v5.15_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Make sure the destroy callback is reset when a event initialization
fails
- Update the event constraints for Icelake
- Make sure the active time of an event is updated even for inactive
events
* tag 'perf_urgent_for_v5.15_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: fix userpage->time_enabled of inactive events
perf/x86/intel: Update event constraints for ICX
perf/x86: Reset destroy callback on event init failure
Linus Torvalds [Sun, 3 Oct 2021 17:23:54 +0000 (10:23 -0700)]
Merge tag 'objtool_urgent_for_v5.15_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fix from Borislav Petkov:
- Handle symbol relocations properly due to changes in the toolchains
which remove section symbols now
* tag 'objtool_urgent_for_v5.15_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Teach get_alt_entry() about more relocation types
Linus Torvalds [Sun, 3 Oct 2021 00:51:01 +0000 (17:51 -0700)]
Merge tag 'hwmon-for-v5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fixed various potential NULL pointer accesses in w8379* drivers
- Improved error handling, fault reporting, and fixed rounding in
thmp421 driver
- Fixed error handling in ltc2947 driver
- Added missing attribute to pmbus/mp2975 driver
- Fixed attribute values in pbus/ibm-cffps, occ, and mlxreg-fan
drivers
- Removed unused residual code from k10temp driver
* tag 'hwmon-for-v5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (w83793) Fix NULL pointer dereference by removing unnecessary structure field
hwmon: (w83792d) Fix NULL pointer dereference by removing unnecessary structure field
hwmon: (w83791d) Fix NULL pointer dereference by removing unnecessary structure field
hwmon: (pmbus/mp2975) Add missed POUT attribute for page 1 mp2975 controller
hwmon: (pmbus/ibm-cffps) max_power_out swap changes
hwmon: (occ) Fix P10 VRM temp sensors
hwmon: (ltc2947) Properly handle errors when looking for the external clock
hwmon: (tmp421) fix rounding for negative values
hwmon: (tmp421) report /PVLD condition as fault
hwmon: (tmp421) handle I2C errors
hwmon: (mlxreg-fan) Return non-zero value when fan current state is enforced from sysfs
hwmon: (k10temp) Remove residues of current and voltage
- fix for wrong infolevel struct used in some getattr/setattr paths
- two small documentation fixes"
* tag '5.15-rc3-ksmbd-fixes' of git://git.samba.org/ksmbd:
ksmbd: missing check for NULL in convert_to_nt_pathname()
ksmbd: fix transform header validation
ksmbd: add buffer validation for SMB2_CREATE_CONTEXT
ksmbd: add validation in smb2 negotiate
ksmbd: add request buffer validation in smb2_set_info
ksmbd: use correct basic info level in set_file_basic_info()
ksmbd: remove NTLMv1 authentication
ksmbd: fix documentation for 2 functions
MAINTAINERS: rename cifs_common to smbfs_common in cifs and ksmbd entry
ksmbd: fix invalid request buffer access in compound
ksmbd: remove RFC1002 check in smb2 request
Linus Torvalds [Sat, 2 Oct 2021 19:56:03 +0000 (12:56 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five fairly minor fixes and spelling updates, all in drivers. Even
though the ufs fix is in tracing, it's a potentially exploitable use
beyond end of array bug"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: csiostor: Add module softdep on cxgb4
scsi: qla2xxx: Fix excessive messages during device logout
scsi: virtio_scsi: Fix spelling mistake "Unsupport" -> "Unsupported"
scsi: ses: Fix unsigned comparison with less than zero
scsi: ufs: Fix illegal offset in UPIU event trace
Linus Torvalds [Sat, 2 Oct 2021 18:00:36 +0000 (11:00 -0700)]
Merge tag 'block-5.15-2021-10-01' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few block fixes for this release:
- Revert a BFQ commit that causes breakage for people. Unfortunately
it was auto-selected for stable as well, so now 5.14.7 suffers from
it too. Hopefully stable will pick up this revert quickly too, so
we can remove the issue on that end as well.
- Add a quirk for Apple NVMe controllers, which due to their
non-compliance broke due to the introduction of command sequences
(Keith)
- Use shifts in nbd, fixing a __divdi3 issue (Nick)"
* tag 'block-5.15-2021-10-01' of git://git.kernel.dk/linux-block:
nbd: use shifts rather than multiplies
Revert "block, bfq: honor already-setup queue merges"
nvme: add command id quirk for apple controllers
Linus Torvalds [Sat, 2 Oct 2021 17:26:19 +0000 (10:26 -0700)]
Merge tag 'io_uring-5.15-2021-10-01' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Two fixes in here:
- The signal issue that was discussed start of this week (me).
- Kill dead fasync support in io_uring. Looks like it was broken
since io_uring was initially merged, and given that nobody has ever
complained about it, let's just kill it (Pavel)"
* tag 'io_uring-5.15-2021-10-01' of git://git.kernel.dk/linux-block:
io_uring: kill fasync
io-wq: exclusively gate signal based exit on get_signal() return
Linus Torvalds [Sat, 2 Oct 2021 17:08:35 +0000 (10:08 -0700)]
Merge tag 'libnvdimm-fixes-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A fix for a regression added this cycle in the pmem driver, and for a
long standing bug for failed NUMA node lookups on ARM64.
This has appeared in -next for several days with no reported issues.
Summary:
- Fix a regression that caused the sysfs ABI for pmem block devices
to not be registered. This fails the nvdimm unit tests and dax
xfstests.
- Fix numa node lookups for dax-kmem memory (device-dax memory
assigned to the page allocator) on ARM64"
* tag 'libnvdimm-fixes-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm/pmem: fix creating the dax group
ACPI: NFIT: Use fallback node id when numa info in NFIT table is incorrect
cachefiles: Fix oops in trace_cachefiles_mark_buried due to NULL object
In cachefiles_mark_object_buried, the dentry in question may not have an
owner, and thus our cachefiles_object pointer may be NULL when calling
the tracepoint, in which case we will also not have a valid debug_id to
print in the tracepoint.
Check for NULL object in the tracepoint and if so, just set debug_id to
MAX_UINT as was done in 2908f5e101e3 ("fscache: Add a cookie debug ID
and use that in traces").
Hugh Dickins [Sat, 2 Oct 2021 10:17:29 +0000 (03:17 -0700)]
drm/i915: fix blank screen booting crashes
5.15-rc1 crashes with blank screen when booting up on two ThinkPads
using i915. Bisections converge convincingly, but arrive at different
and suprising "culprits", none of them the actual culprit.
netconsole (with init_netconsole() hacked to call i915_init() when
logging has started, instead of by module_init()) tells the story:
kernel BUG at drivers/gpu/drm/i915/i915_sw_fence.c:245!
with RSI: ffffffff814d408b pointing to sw_fence_dummy_notify().
I've been building with CONFIG_CC_OPTIMIZE_FOR_SIZE=y, and that
function needs to be 4-byte aligned.
hwmon: (w83793) Fix NULL pointer dereference by removing unnecessary structure field
If driver read tmp value sufficient for
(tmp & 0x08) && (!(tmp & 0x80)) && ((tmp & 0x7) == ((tmp >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
hwmon: (w83792d) Fix NULL pointer dereference by removing unnecessary structure field
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
hwmon: (w83791d) Fix NULL pointer dereference by removing unnecessary structure field
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
The bytes for max_power_out from the ibm-cffps devices differ in byte
order for some power supplies.
The Witherspoon power supply returns the bytes in MSB/LSB order.
The Rainier power supply returns the bytes in LSB/MSB order.
The Witherspoon power supply uses version cffps1. The Rainier power
supply should use version cffps2. If version is cffps1, swap the bytes
before output to max_power_out.
Eddie James [Wed, 29 Sep 2021 15:36:04 +0000 (10:36 -0500)]
hwmon: (occ) Fix P10 VRM temp sensors
The P10 (temp sensor version 0x10) doesn't do the same VRM status
reporting that was used on P9. It just reports the temperature, so
drop the check for VRM fru type in the sysfs show function, and don't
set the name to "alarm".
Because Rui is now going to focus on work that is not related to the
maintenance of the thermal subsystem in the kernel, Rafael will start
to help Daniel with handling the development process as a new member
of the thermal maintainers team. Rui will continue to review patches
in that area.
The thermal development process flow will change so that the material
from the thermal git tree will be merged into the thermal branch of
the linux-pm.git tree before going into the mainline.
Update the information in MAINTAINERS accordingly.
Linus Torvalds [Fri, 1 Oct 2021 18:08:07 +0000 (11:08 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more kvm fixes from Paolo Bonzini:
"Small x86 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: selftests: Ensure all migrations are performed when test is affined
KVM: x86: Swap order of CPUID entry "index" vs. "significant flag" checks
ptp: Fix ptp_kvm_getcrosststamp issue for x86 ptp_kvm
x86/kvmclock: Move this_cpu_pvti into kvmclock.h
selftests: KVM: Don't clobber XMM register when read
KVM: VMX: Fix a TSX_CTRL_CPUID_CLEAR field mask issue
Linus Torvalds [Fri, 1 Oct 2021 17:27:44 +0000 (10:27 -0700)]
Merge tag 'drm-fixes-2021-10-01' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Daniel Vetter:
"Dave is out on a long w/e, should be back next week.
Nothing nefarious, just a bunch of driver fixes: amdgpu, i915, tegra,
and one exynos driver fix"
* tag 'drm-fixes-2021-10-01' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: force exit gfxoff on sdma resume for rmb s0ix
drm/amdgpu: check tiling flags when creating FB on GFX8-
drm/amd/display: Pass PCI deviceid into DC
drm/amd/display: initialize backlight_ramping_override to false
drm/amdgpu: correct initial cp_hqd_quantum for gfx9
drm/amd/display: Fix Display Flicker on embedded panels
drm/amdgpu: fix gart.bo pin_count leak
drm/i915: Remove warning from the rps worker
drm/i915/request: fix early tracepoints
drm/i915/guc, docs: Fix pdfdocs build error by removing nested grid
gpu: host1x: Plug potential memory leak
gpu/host1x: fence: Make spinlock static
drm/tegra: uapi: Fix wrong mapping end address in case of disabled IOMMU
drm/tegra: dc: Remove unused variables
drm/exynos: Make use of the helper function devm_platform_ioremap_resource()
drm/i915/gvt: fix the usage of ww lock in gvt scheduler.
Pavel Begunkov [Fri, 1 Oct 2021 09:39:33 +0000 (10:39 +0100)]
io_uring: kill fasync
We have never supported fasync properly, it would only fire when there
is something polling io_uring making it useless. The original support came
in through the initial io_uring merge for 5.1. Since it's broken and
nobody has reported it, get rid of the fasync bits.
Linus Torvalds [Fri, 1 Oct 2021 17:14:29 +0000 (10:14 -0700)]
Merge tag 'iommu-fixes-v5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Two fixes for the new Apple DART driver to fix a kernel panic and a
stale data usage issue
- Intel VT-d fix for how PCI device ids are printed
* tag 'iommu-fixes-v5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dart: Clear sid2group entry when a group is freed
iommu/vt-d: Drop "0x" prefix from PCI bus & device addresses
iommu/dart: Remove iommu_flush_ops
Michal Koutný [Fri, 17 Sep 2021 15:30:37 +0000 (17:30 +0200)]
sched/fair: Add ancestors of unthrottled undecayed cfs_rq
Since commit a7b359fc6a37 ("sched/fair: Correctly insert cfs_rq's to
list on unthrottle") we add cfs_rqs with no runnable tasks but not fully
decayed into the load (leaf) list. We may ignore adding some ancestors
and therefore breaking tmp_alone_branch invariant. This broke LTP test
cfs_bandwidth01 and it was partially fixed in commit fdaba61ef8a2
("sched/fair: Ensure that the CFS parent is added after unthrottling").
I noticed the named test still fails even with the fix (but with low
probability, 1 in ~1000 executions of the test). The reason is when
bailing out of unthrottle_cfs_rq early, we may miss adding ancestors of
the unthrottled cfs_rq, thus, not joining tmp_alone_branch properly.
Fix this by adding ancestors if we notice the unthrottled cfs_rq was
added to the load list.
Song Liu [Wed, 29 Sep 2021 19:43:13 +0000 (12:43 -0700)]
perf/core: fix userpage->time_enabled of inactive events
Users of rdpmc rely on the mmapped user page to calculate accurate
time_enabled. Currently, userpage->time_enabled is only updated when the
event is added to the pmu. As a result, inactive event (due to counter
multiplexing) does not have accurate userpage->time_enabled. This can
be reproduced with something like:
/* open 20 task perf_event "cycles", to create multiplexing */
fd = perf_event_open(); /* open task perf_event "cycles" */
userpage = mmap(fd); /* use mmap and rdmpc */
while (true) {
time_enabled_mmap = xxx; /* use logic in perf_event_mmap_page */
time_enabled_read = read(fd).time_enabled;
if (time_enabled_mmap > time_enabled_read)
BUG();
}
Fix this by updating userpage for inactive events in merge_sched_in.
perf/x86: Reset destroy callback on event init failure
perf_init_event tries multiple init callbacks and does not reset the
event state between tries. When x86_pmu_event_init runs, it
unconditionally sets the destroy callback to hw_perf_event_destroy. On
the next init attempt after x86_pmu_event_init, in perf_try_init_event,
if the pmu's capabilities includes PERF_PMU_CAP_NO_EXCLUDE, the destroy
callback will be run. However, if the next init didn't set the destroy
callback, hw_perf_event_destroy will be run (since the callback wasn't
reset).
Looking at other pmu init functions, the common pattern is to only set
the destroy callback on a successful init. Resetting the callback on
failure tries to replicate that pattern.
This was discovered after commit f11dd0d80555 ("perf/x86/amd/ibs: Extend
PERF_PMU_CAP_NO_EXCLUDE to IBS Op") when the second (and only second)
run of the perf tool after a reboot results in 0 samples being
generated. The extra run of hw_perf_event_destroy results in
active_events having an extra decrement on each perf run. The second run
has active_events == 0 and every subsequent run has active_events < 0.
When active_events == 0, the NMI handler will early-out and not record
any samples.
Peter Zijlstra [Thu, 30 Sep 2021 10:43:10 +0000 (12:43 +0200)]
objtool: Teach get_alt_entry() about more relocation types
Occasionally objtool encounters symbol (as opposed to section)
relocations in .altinstructions. Typically they are the alternatives
written by elf_add_alternative() as encountered on a noinstr
validation run on vmlinux after having already ran objtool on the
individual .o files.
Basically this is the counterpart of commit 44f6a7c0755d ("objtool:
Fix seg fault with Clang non-section symbols"), because when these new
assemblers (binutils now also does this) strip the section symbols,
elf_add_reloc_to_insn() is forced to emit symbol based relocations.
As such, teach get_alt_entry() about different relocation types.
Zhang Yi [Fri, 10 Sep 2021 08:03:16 +0000 (16:03 +0800)]
ext4: recheck buffer uptodate bit under buffer lock
Commit 8e33fadf945a ("ext4: remove an unnecessary if statement in
__ext4_get_inode_loc()") forget to recheck buffer's uptodate bit again
under buffer lock, which may overwrite the buffer if someone else have
already brought it uptodate and changed it.
ext4: fix potential infinite loop in ext4_dx_readdir()
When ext4_htree_fill_tree() fails, ext4_dx_readdir() can run into an
infinite loop since if info->last_pos != ctx->pos this will reset the
directory scan and reread the failing entry. For example:
1. a dx_dir which has 3 block, block 0 as dx_root block, block 1/2 as
leaf block which own the ext4_dir_entry_2
2. block 1 read ok and call_filldir which will fill the dirent and update
the ctx->pos
3. block 2 read fail, but we has already fill some dirent, so we will
return back to userspace will a positive return val(see ksys_getdents64)
4. the second ext4_dx_readdir will reset the world since info->last_pos
!= ctx->pos, and will also init the curr_hash which pos to block 1
5. So we will read block1 too, and once block2 still read fail, we can
only fill one dirent because the hash of the entry in block1(besides
the last one) won't greater than curr_hash
6. this time, we forget update last_pos too since the read for block2
will fail, and since we has got the one entry, ksys_getdents64 can
return success
7. Latter we will trapped in a loop with step 4~6
ext4: flush s_error_work before journal destroy in ext4_fill_super
The error path in ext4_fill_super forget to flush s_error_work before
journal destroy, and it may trigger the follow bug since
flush_stashed_error_work can run concurrently with journal destroy
without any protection for sbi->s_journal.
static int start_this_handle(...)
BUG_ON(journal->j_flags & JBD2_UNMOUNT); <---- Trigger this
Besides, after we enable fast commit, ext4_fc_replay can add work to
s_error_work but return success, so the latter journal destroy in
ext4_load_journal can trigger this problem too.
Fix this problem with two steps:
1. Call ext4_commit_super directly in ext4_handle_error for the case
that called from ext4_fc_replay
2. Since it's hard to pair the init and flush for s_error_work, we'd
better add a extras flush_work before journal destroy in
ext4_fill_super
Besides, this patch will call ext4_commit_super in ext4_handle_error for
any nojournal case too. But it seems safe since the reason we call
schedule_work was that we should save error info to sb through journal
if available. Conversely, for the nojournal case, it seems useless delay
commit superblock to s_error_work.
Ritesh Harjani [Sat, 5 Jun 2021 05:09:32 +0000 (10:39 +0530)]
ext4: fix loff_t overflow in ext4_max_bitmap_size()
We should use unsigned long long rather than loff_t to avoid
overflow in ext4_max_bitmap_size() for comparison before returning.
w/o this patch sbi->s_bitmap_maxbytes was becoming a negative
value due to overflow of upper_limit (with has_huge_files as true)
Below is a quick test to trigger it on a 64KB pagesize system.
sudo mkfs.ext4 -b 65536 -O ^has_extents,^64bit /dev/loop2
sudo mount /dev/loop2 /mnt
sudo echo "hello" > /mnt/hello -> This will error out with
"echo: write error: File too large"
Jeffle Xu [Mon, 23 Aug 2021 06:13:58 +0000 (14:13 +0800)]
ext4: fix reserved space counter leakage
When ext4_insert_delayed block receives and recovers from an error from
ext4_es_insert_delayed_block(), e.g., ENOMEM, it does not release the
space it has reserved for that block insertion as it should. One effect
of this bug is that s_dirtyclusters_counter is not decremented and
remains incorrectly elevated until the file system has been unmounted.
This can result in premature ENOSPC returns and apparent loss of free
space.
Another effect of this bug is that
/sys/fs/ext4/<dev>/delayed_allocation_blocks can remain non-zero even
after syncfs has been executed on the filesystem.
Besides, add check for s_dirtyclusters_counter when inode is going to be
evicted and freed. s_dirtyclusters_counter can still keep non-zero until
inode is written back in .evict_inode(), and thus the check is delayed
to .destroy_inode().
Hou Tao [Fri, 20 Aug 2021 04:45:05 +0000 (12:45 +0800)]
ext4: limit the number of blocks in one ADD_RANGE TLV
Now EXT4_FC_TAG_ADD_RANGE uses ext4_extent to track the
newly-added blocks, but the limit on the max value of
ee_len field is ignored, and it can lead to BUG_ON as
shown below when running command "fallocate -l 128M file"
on a fast_commit-enabled fs:
projects / linux.git / log