Eric Dumazet [Fri, 17 Jul 2015 08:19:23 +0000 (10:19 +0200)]
caif: fix leaks and race in caif_queue_rcv_skb()
1) If sk_filter() is applied, skb was leaked (not freed)
2) Testing SOCK_DEAD twice is racy :
packet could be freed while already queued.
3) Remove obsolete comment about caching skb->len
Let TC+eBPF programs call skb_vlan_push/pop via helpers.
v1->v2:
- reworded commit log to better explain correctness of re-caching
and fixed comparison of mixed endiannes (suggested by Eric)
====================
improve accuracy of timing in test_bpf and add two stress tests:
- {skb->data[0], get_smp_processor_id} repeated 2k times
- {skb->data[0], vlan_push} x 68 followed by {skb->data[0], vlan_pop} x 68
1st test is useful to test performance of JIT implementation of BPF_LD_ABS
together with BPF_CALL instructions.
2nd test is stressing skb_vlan_push/pop logic together with skb->data access
via BPF_LD_ABS insn which checks that re-caching of skb->data is done correctly.
In order to call bpf_skb_vlan_push() from test_bpf.ko have to add
three export_symbol_gpl.
Allow eBPF programs attached to TC qdiscs call skb_vlan_push/pop via
helper functions. These functions may change skb->data/hlen which are
cached by some JITs to improve performance of ld_abs/ld_ind instructions.
Therefore JITs need to recognize bpf_skb_vlan_push/pop() calls,
re-compute header len and re-cache skb->data/hlen back into cpu registers.
Note, skb->data/hlen are not directly accessible from the programs,
so any changes to skb->data done either by these helpers or by other
TC actions are safe.
eBPF JIT supported by three architectures:
- arm64 JIT is using bpf_load_pointer() without caching, so it's ok as-is.
- x64 JIT re-caches skb->data/hlen unconditionally after vlan_push/pop calls
(experiments showed that conditional re-caching is slower).
- s390 JIT falls back to interpreter for now when bpf_skb_vlan_push() is present
in the program (re-caching is tbd).
These helpers allow more scalable handling of vlan from the programs.
Instead of creating thousands of vlan netdevs on top of eth0 and attaching
TC+ingress+bpf to all of them, the program can be attached to eth0 directly
and manipulate vlans as necessary.
David S. Miller [Tue, 21 Jul 2015 03:50:19 +0000 (20:50 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-07-17
This series contains updates to igb, ixgbe, ixgbevf, i40e, bnx2x,
freescale, siena and dp83640.
Jacob provides several patches to clarify the intended way to implement
both SIOCSHWTSTAMP and ethtool's get_ts_info(). It is okay to support
the specific filters in SIOCSHWTSTAMP by upscaling them to the generic
filters.
Alex Duyck provides a igb patch to pull the time stamp from the fragment
before it gets added to the skb, to avoid a possible issue in which the
fragment can possibly be less than IGB_RX_HDR_LEN due to the time stamp
being pulled after the copybreak check. Also provides a ixgbevf patch to
fold the ixgbevf_pull_tail() call into ixgbevf_add_rx_frag(), which gives
the advantage that the fragment does not have to be modified after it is
added to the skb.
Fan provides patches for ixgbe/ixgbevf to set the receive hash type
based on receive descriptor RSS type.
Todd provides a fix for igb where on check for link on any media other
than copper was not being detected since it was looking on the incorrect
PHY page (due to the page being used gets switched before the function
to check link gets executed).
====================
This patch series reworks how we perform PHY initialization and resets in the
GENET driver. Although this contains mostly fixes, some of the changes are a
bit too intrusive to be backported to 'net' at the moment.
Some of the motivations behind these changes were to reduce the time spent in how
performing MDIO transactions, since it is better to perform then when we have
interrupts enabled. This reduces the bring-up time of GENET from ~600 msecs down
to ~8 msecs, and about the same time for suspend/resume.
Since I do not currently have a system which is not DT-aware, can you (Petri,
Jaedon) give this a try and confirm things keep working as expected?
====================
net: bcmgenet: Remove init parameter from bcmgenet_mii_config
Now that we have reworked the way we perform the PHY initialization, we
no longer need to differentiate between init time vs. non-init time
calls, just use a dev_info_once() print to print the PHY type.
net: bcmgenet: Delay PHY initialization to bcmgenet_open()
We are currently doing a full PHY initialization and even starting the
pHY state machine during bcmgenet_mii_init() which is executed in the
driver's probe function. This is convenient to determine whether we can
attach to a proper PHY device but comes at the expense of spending up to
10ms per MDIO transactions (to reach the waitqueue timeout), which slows
things down.
This also creates a sitaution where we end-up attaching twice to the
PHY, which is not quite correct either.
Fix this by moving bcmgenet_mii_probe() into bcmgenet_open() and update
its error path accordingly.
Avoid printing the message "attached PHY at address 1 [...]" every time
we bring up/down the interface and remove this print since it duplicates
what the PHY driver already does for us.
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: bcmgenet: Determine PHY type before scanning MDIO bus
Our internal GPHY might be powered off before we attempt scanning the
MDIO bus and bind a driver to it. The way we are currently determining
whether a PHY is internal or not is done *after* we have successfully
matched its driver. If the PHY is powered down, it will not respond to
the MDIO bus, so we will not be able to bind a driver to it.
Our Device Tree for GENET interfaces specifies a "phy-mode" value:
"internal" which tells if this internal uses an internal PHY or not.
If of_get_phy_mode() fails to parse the 'phy-mode' property, do an
additional manual lookup, and if we find "internal" set the
corresponding internal variable accordingly.
Replace all uses of phy_is_internal() with a check against
priv->internal_phy to avoid having to rely on whether or not
priv->phydev is set correctly.
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: bcmgenet: Power on integrated GPHY in bcmgenet_power_up()
We are currently disabling the GPHY interface during bcmgenet_close(),
and attempting to power it back on during bcmgenet_open(). This works
fine for the first time, because we called bcmgenet_mii_config() which
took care of enabling the interface, however, bcmgenet_power_up() really
needs to power on the GPHY for correctness.
This will be particularly important as we want to move
bcmgenet_mii_probe() down to bcmgenet_open() to avoid seeing the "PHY
already attached" message.
Fixes: a642c4f7906f36 ("net: bcmgenet: power up and down integrated GPHY when unused") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
bcmgenet_open()'s error path call free_irq() with a dev_id argument
different from the one we used to call request_irq() with, this will
make us trip over the warning in kernel/irq/manage.c:__free_irq()
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
We are currently issuing multiple PHY resets during a suspend/resume,
first during bcmgenet_power_up() which does a hardware reset, then a
software reset by calling bcmgenet_mii_reset(). This is both unnecessary
and can take as long as 10ms per MDIO transactions while we re-apply
workarounds because we do not yet have MDIO interrupts enabled.
phy_resume() takes care of re-apply our workarounds in case we need any,
and bcmgenet_power_up() does a PHY hardware reset, all of this is more
than enough to guarantee that the PHY operates correctly.
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Tue, 21 Jul 2015 03:45:58 +0000 (20:45 -0700)]
Merge branch 'stmmac-cleanup'
Joachim Eastwood says:
====================
stmmac clean up for 4.3 part1
This patch set continues the conversion of the dwmac glue layers
to more proper platform drivers. The first part of the patch set
cleans up stmmac_platform a bit. Refactors code from the common
probe function and exports two functions that will be used in
the dwmac-* drivers.
Second part converts two simple dwmac-* drivers to have their
own probe function and use the exported functions. This brings
us closer to point where stmmac_platform is only a library of
common functions for the dwmac-* drivers to use.
The plan next is:
* add probe functions to the rest of the dwmac-* drivers
* move probe function in stmmac_platform to dwmac-generic
* remove struct stmmac_of_data and let those drivers
that actually need match data handle it themselves
* clean up include/linux/stmmac.h
Note that this patch set has only been tested on lpc18xx so
testing on other platforms is greatly appreciated.
Previous parts can be found here:
http://www.spinics.net/lists/netdev/msg328997.html
http://www.spinics.net/lists/netdev/msg329932.html
====================
Joachim Eastwood [Thu, 16 Jul 2015 22:26:11 +0000 (00:26 +0200)]
stmmac: add proper probe function to dwmac-meson
By using a few functions from stmmac_platform we can now create
a proper probe function in this driver. By doing so we can drop
the OF match data and simplify the overall driver.
Joachim Eastwood [Thu, 16 Jul 2015 22:26:10 +0000 (00:26 +0200)]
stmmac: add proper probe function to dwmac-lpc18xx
By using a few functions from stmmac_platform we can now create
a proper probe function in this driver. By doing so we can drop
the OF match data and simplify the overall driver.
Joachim Eastwood [Thu, 16 Jul 2015 22:26:09 +0000 (00:26 +0200)]
stmmac: export probe_config_dt() and get_platform_resources()
Export stmmac_probe_config_dt() and stmmac_get_platform_resources()
so they can be used in the dwmac-* drivers themselves. This will
allow us to build more flexible and standalone drivers which just
use stmmac_platform as a library for setup functions.
Joachim Eastwood [Thu, 16 Jul 2015 22:26:08 +0000 (00:26 +0200)]
stmmac: make stmmac_probe_config_dt return the platform data struct
Since stmmac_probe_config_dt() allocates the platform data structure
it is cleaner if it just returned this structure directly. This
function will later be used in the probe function in dwmac-* drivers.
Joachim Eastwood [Thu, 16 Jul 2015 22:26:07 +0000 (00:26 +0200)]
stmmac: introduce stmmac_get_platform_resources()
Refactor all code that deals with platform resources into it's
own get function. This function will later be used in the probe
function in dwmac-* drivers.
Joachim Eastwood [Thu, 16 Jul 2015 22:26:06 +0000 (00:26 +0200)]
stmmac: clean up platform/of_match data retrieval
Refactor code to clearly separate probing non-dt versus dt. In the
non-dt case platform data must be supplied to probe successfully.
For dt the platform data structure is created and match data is
copied into it. Note that support for supplying platform data in
dt from AUXDATA is dropped as no users in mainline does this.
This change will allow dt dwmac-* drivers to call the config_dt()
function from probe to create the needed platform data struct and
retrieve common dt properties.
qmi_wwan: add the second QMI/network interface for Sierra Wireless MC7305/MC7355
Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.
Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:31 +0000 (16:54 -0400)]
tipc: reduce locking scope during packet reception
We convert packet/message reception according to the same principle
we have been using for message sending and timeout handling:
We move the function tipc_rcv() to node.c, hence handling the initial
packet reception at the link aggregation level. The function grabs
the node lock, selects the receiving link, and accesses it via a new
call tipc_link_rcv(). This function appends buffers to the input
queue for delivery upwards, but it may also append outgoing packets
to the xmit queue, just as we do during regular message sending. The
latter will happen when buffers are forwarded from the link backlog,
or when retransmission is requested.
Upon return of this function, and after having released the node lock,
tipc_rcv() delivers/tranmsits the contents of those queues, but it may
also perform actions such as link activation or reset, as indicated by
the return flags from the link.
This reduces the number of cpu cycles spent inside the node spinlock,
and reduces contention on that lock.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:30 +0000 (16:54 -0400)]
tipc: introduce node contact FSM
The logics for determining when a node is permitted to establish
and maintain contact with its peer node becomes non-trivial in the
presence of multiple parallel links that may come and go independently.
A known failure scenario is that one endpoint registers both its links
to the peer lost, cleans up it binding table, and prepares for a table
update once contact is re-establihed, while the other endpoint may
see its links reset and re-established one by one, hence seeing
no need to re-synchronize the binding table. To avoid this, a node
must not allow re-establishing contact until it has confirmation that
even the peer has lost both links.
Currently, the mechanism for handling this consists of setting and
resetting two state flags from different locations in the code. This
solution is hard to understand and maintain. A closer analysis even
reveals that it is not completely safe.
In this commit we do instead introduce an FSM that keeps track of
the conditions for when the node can establish and maintain links.
It has six states and four events, and is strictly based on explicit
knowledge about the own node's and the peer node's contact states.
Only events leading to state change are shown as edges in the figure
below.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:29 +0000 (16:54 -0400)]
tipc: move link supervision timer to node level
In our effort to move control of the links to the link aggregation
layer, we move the perodic link supervision timer to struct tipc_node.
The new timer is shared between all links belonging to the node, thus
saving resources, while still kicking the FSM on both its pertaining
links at each expiration.
The current link timer and corresponding functions are removed.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:28 +0000 (16:54 -0400)]
tipc: simplify link timer implementation
We create a second, simpler, link timer function, tipc_link_timeout().
The new function makes use of the new FSM function introduced in the
previous commit, and just like it, takes a buffer queue as parameter.
It returns an event bit field and potentially a link protocol packet
to the caller.
The existing timer function, link_timeout(), is still needed for a
while, so we redesign it to become a wrapper around the new function.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:27 +0000 (16:54 -0400)]
tipc: improve link FSM implementation
The link FSM implementation is currently unnecessarily complex.
It sometimes checks for conditional state outside the FSM data
before deciding next state, and often performs actions directly
inside the FSM logics.
In this commit, we create a second, simpler FSM implementation,
that as far as possible acts only on states and events that it is
strictly defined for, and postpone any actions until it is finished
with its decisions. It also returns an event flag field and an a
buffer queue which may potentially contain a protocol message to
be sent by the caller.
Unfortunately, we cannot yet make the FSM "clean", in the sense
that its decisions are only based on FSM state and event, and that
state changes happen only here. That will have to wait until the
activate/reset logics has been cleaned up in a future commit.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:26 +0000 (16:54 -0400)]
tipc: introduce new link protocol msg create function
As a preparation for later changes, we introduce a new function
tipc_link_build_proto_msg(). Instead of actually sending the created
protocol message, it only creates it and adds it to the head of a
skb queue provided by the caller.
Since we still need the existing function tipc_link_protocol_xmit()
for a while, we redesign it to make use of the new function.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:25 +0000 (16:54 -0400)]
tipc: clean up definitions and usage of link flags
The status flag LINK_STOPPED is not needed any more, since the
mechanism for delayed deletion of links has been removed.
Likewise, LINK_STARTED and LINK_START_EVT are unnecessary,
because we can just as well start the link timer directly from
inside tipc_link_create().
We eliminate these flags in this commit.
Instead of the above flags, we now introduce three new link modes,
TIPC_LINK_OPEN, TIPC_LINK_BLOCKED and TIPC_LINK_TUNNEL. The values
indicate whether, and in the case of TIPC_LINK_TUNNEL, which, messages
the link is allowed to receive in this state. TIPC_LINK_BLOCKED also
blocks timer-driven protocol messages to be sent out, and any change
to the link FSM. Since the modes are mutually exclusive, we convert
them to state values, and rename the 'flags' field in struct tipc_link
to 'exec_mode'.
Finally, we move the #defines for link FSM states and events from link.h
into enums inside the file link.c, which is the real usage scope of
these definitions.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:24 +0000 (16:54 -0400)]
tipc: make media xmit call outside node spinlock context
Currently, message sending is performed through a deep call chain,
where the node spinlock is grabbed and held during a significant
part of the transmission time. This is clearly detrimental to
overall throughput performance; it would be better if we could send
the message after the spinlock has been released.
In this commit, we do instead let the call revert on the stack after
the buffer chain has been added to the transmission queue, whereafter
clones of the buffers are transmitted to the device layer outside the
spinlock scope.
As a further step in our effort to separate the roles of the node
and link entities we also move the function tipc_link_xmit() to
node.c, and rename it to tipc_node_xmit().
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:23 +0000 (16:54 -0400)]
tipc: change sk_buffer handling in tipc_link_xmit()
When the function tipc_link_xmit() is given a buffer list for
transmission, it currently consumes the list both when transmission
is successful and when it fails, except for the special case when
it encounters link congestion.
This behavior is inconsistent, and needs to be corrected if we want
to avoid problems in later commits in this series.
In this commit, we change this to let the function consume the list
only when transmission is successful, and leave the list with the
sender in all other cases. We also modifiy the socket code so that
it adapts to this change, i.e., purges the list when a non-congestion
error code is returned.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:22 +0000 (16:54 -0400)]
tipc: use bearer index when looking up active links
struct tipc_node currently holds two arrays of link pointers; one,
indexed by bearer identity, which contains all links irrespective of
current state, and one two-slot array for the currently active link
or links. The latter array contains direct pointers into the elements
of the former. This has the effect that we cannot know the bearer id of
a link when accessing it via the "active_links[]" array without actually
dereferencing the pointer, something we want to avoid in some cases.
In this commit, we do instead store the bearer identity in the
"active_links" array, and use this as an index to find the right element
in the overall link entry array. This change should be seen as a
preparation for the later commits in this series.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:21 +0000 (16:54 -0400)]
tipc: move link input queue to tipc_node
At present, the link input queue and the name distributor receive
queues are fields aggregated in struct tipc_link. This is a hazard,
because a link might be deleted while a receiving socket still keeps
reference to one of the queues.
This commit fixes this bug. However, rather than adding yet another
reference counter to the critical data path, we move the two queues
to safe ground inside struct tipc_node, which is already protected, and
let the link code only handle references to the queues. This is also
in line with planned later changes in this area.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:20 +0000 (16:54 -0400)]
tipc: move link creation from neighbor discoverer to node
As a step towards turning links into node internal entities, we move the
creation of links from the neighbor discovery logics to the node's link
control logics.
We also create an additional entry for the link's media address in the
newly introduced struct tipc_link_entry, since this is where it is
needed in the upcoming commits. The current copy in struct tipc_link
is kept for now, but will be removed later.
Jon Paul Maloy [Thu, 16 Jul 2015 20:54:19 +0000 (16:54 -0400)]
tipc: introduce link entry structure to struct tipc_node
struct 'tipc_node' currently contains two arrays for link attributes,
one for the link pointers, and one for the usable link MTUs.
We now group those into a new struct 'tipc_link_entry', and intoduce
one single array consisting of such enties. Apart from being a cosmetic
improvement, this is a starting point for the strict master-slave
relation between node and link that we will introduce in the following
commits.
net: netcp: fix improper initialization in netcp_ndo_open()
The keystone qmss will raise interrupt when packet arrive at the
receive queue. Only control available to avoid interrupt from happening
is to keep the free descriptor queue (FDQ) empty in the receive side.
So the filling of descriptors into the FDQ has to happen after
request_irq() call is made as part of knav_queue_enable_notify(). So
move the function netcp_rxpool_refill() after this call.
bonding: correct the MAC address for "follow" fail_over_mac policy
The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:
1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
bond0 has the same mac address with eth0, it is MAC1.
2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
eth1 is backup, eth1 has MAC2.
3) ifconfig eth0 down
eth1 became active slave, bond will swap MAC for eth0 and eth1,
so eth1 has MAC1, and eth0 has MAC2.
4) ifconfig eth1 down
there is no active slave, and eth1 still has MAC1, eth2 has MAC2.
5) ifconfig eth0 up
the eth0 became active slave again, the bond set eth0 to MAC1.
Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.
This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.
- Per Nicolas Dichtel review: remove errant empty union.
v2:
- Per davem review: in sk_buff, union fwd_mark with secmark to save space
since features appear to be mutually exclusive.
- Per Simon Horman review:
- fix grammar in switchdev.txt wrt fwd_mark
- remove some unrelated changes that snuck in
v1:
This patchset was previously submitted as RFC. No changes from the last
version (v2) sent under RFC. Including RFC version history here for reference.
RFC v2:
- s/fwd_mark/offload_fwd_mark
- use consume_skb rather than kfree_skb when dropping pkt on egress.
- Use Jiri's suggestion to use ifindex of one of the ports in a group
as the mark for all the ports in the group. This can be done with
no additional storage (no hashtable from v1). To pull it off, we
need some simple recursive routines to walk the netdev tree ensuring
all leaves in the tree (ports) in the same group (e.g. bridge)
belonging to the same switch device will have the same offload fwd mark.
Maybe someone sees a better design for the recusive routines? They're
not too bad, and should cover the stacked driver cases.
RFC v1:
With switchdev support for offloading L2/L3 forwarding data path to a
switch device, we have a general problem where both the device and the
kernel may forward the packet, resulting in duplicate packets on the wire.
Anytime a packet is forwarded by the device and a copy is sent to the CPU,
there is potential for duplicate forwarding, as the kernel may also do a
forwarding lookup and send the packet on the wire.
The specific problem this patch series is interested in solving is avoiding
duplicate packets on bridged ports. There was a previous RFC from Roopa
(http://marc.info/?l=linux-netdev&m=142687073314252&w=2) to address this
problem, but didn't solve the problem of mixed ports in the bridge from
different devices; there was no way to exclude some ports from forwarding
and include others. This RFC solves that problem by tagging the ingressing
packet with a unique mark, and then comparing the packet mark with the
egress port mark, and skip forwarding when there is a match. For the mixed
ports bridge case, only those ports with matching marks are skipped.
The switchdev port driver must do two things:
1) Generate a fwd_mark for each switch port, using some unique key of the
switch device (and optionally port). This is done when the port netdev
is registered or if the port's group membership changes (joins/leaves
a bridge, for example).
2) On packet ingress from port, mark the skb with the ingress port's
fwd_mark. If the device supports it, it's useful to only mark skbs
which were already forwarded by the device. If the device does not
support such indication, all skbs can be marked, even if they're
local dst.
Two new 32-bit fields are added to struct sk_buff and struct netdevice to
hold the fwd_mark. I've wrapped these with CONFIG_NET_SWITCHDEV for now. I
tried using skb->mark for this purpose, but ebtables can overwrite the
skb->mark before the bridge gets it, so that will not work.
In general, this fwd_mark can be used for any case where a packet is
forwarded by the device and a copy is sent to the CPU, to avoid the kernel
re-forwarding the packet. sFlow is another use-case that comes to mind,
but I haven't explored the details.
====================
Scott Feldman [Sun, 19 Jul 2015 01:24:51 +0000 (18:24 -0700)]
rocker: add offload_fwd_mark support
If device flags ingress packet as "fwd offload", mark the
skb->offlaod_fwd_mark using the ingress port's dev->offlaod_fwd_mark. This
will be the hint to the kernel that this packet has already been forwarded
by device to egress ports matching skb->offlaod_fwd_mark.
For rocker, derive port dev->offlaod_fwd_mark based on device switch ID and
port ifindex. If port is bridged, use the bridge ifindex rather than the
port ifindex.
Scott Feldman [Sun, 19 Jul 2015 01:24:50 +0000 (18:24 -0700)]
switchdev: add offload_fwd_mark generator helper
skb->offload_fwd_mark and dev->offload_fwd_mark are 32-bit and should be
unique for device and may even be unique for a sub-set of ports within
device, so add switchdev helper function to generate unique marks based on
port's switch ID and group_ifindex. group_ifindex would typically be the
container dev's ifindex, such as the bridge's ifindex.
The generator uses a global hash table to store offload_fwd_marks hashed by
{switch ID, group_ifindex} key.
Scott Feldman [Sun, 19 Jul 2015 01:24:48 +0000 (18:24 -0700)]
net: don't reforward packets already forwarded by offload device
Just before queuing skb for xmit on port, check if skb has been marked by
switchdev port driver as already fordwarded by device. If so, drop skb. A
non-zero skb->offload_fwd_mark field is set by the switchdev port
driver/device on ingress to indicate the skb has already been forwarded by
the device to egress ports with matching dev->skb_mark. The switchdev port
driver would assign a non-zero dev->offload_skb_mark for each device port
netdev during registration, for example.
Simon Horman [Thu, 16 Jul 2015 01:39:14 +0000 (10:39 +0900)]
rocker: forward packets to CPU when port is joined to openvswitch
Teach rocker to forward packets to CPU when a port is joined to Open vSwitch.
There is scope to later refine what is passed up as per Open vSwitch flows
on a port.
This does not change the behaviour of rocker ports that are
not joined to Open vSwitch.
Herbert Xu [Mon, 20 Jul 2015 09:55:38 +0000 (17:55 +0800)]
Revert "sit: Add gro callbacks to sit_offload"
This patch reverts 19424e052fb44da2f00d1a868cbb51f3e9f4bbb5 ("sit:
Add gro callbacks to sit_offload") because it generates packets
that cannot be handled even by our own GSO.
net: dsa: bcm_sf2: do not use indirect reads and writes for 7445E0
7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).
For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.
Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).
We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
bonding: correctly handle bonding type change on enslave failure
If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)
After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
Signed-off-by: Nikolay Aleksandrov <[email protected]> Fixes: e36b9d16c6a6 ("bonding: clean muticast addresses when device changes type") Signed-off-by: David S. Miller <[email protected]>
bridge: mcast: fix br_multicast_dev_del warn when igmp snooping is not defined
Fix:
net/bridge/br_if.c: In function 'br_dev_delete':
>> net/bridge/br_if.c:284:2: error: implicit declaration of function
>> 'br_multicast_dev_del' [-Werror=implicit-function-declaration]
br_multicast_dev_del(br);
^
cc1: some warnings being treated as errors
Phil Sutter [Wed, 15 Jul 2015 19:56:26 +0000 (21:56 +0200)]
net/ipv6: update flowi6_oif in ip6_dst_lookup_flow if not set
Newly created flows don't have flowi6_oif set (at least if the
associated socket is not interface-bound). This leads to a mismatch in
__xfrm6_selector_match() for policies which specify an interface in the
selector (sel->ifindex != 0).
Backtracing shows this happens in code-paths originating from e.g.
ip6_datagram_connect(), rawv6_sendmsg() or tcp_v6_connect(). (UDP was
not tested for.)
In summary, this patch fixes policy matching on outgoing interface for
locally generated packets.
bonding: fix destruction of bond with devices different from arphrd_ether
When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[ 908.963051] eql: event: 9
[ 908.963052] eql: IFF_SLAVE
[ 908.963054] eql: event: 2
[ 908.963056] eql: IFF_SLAVE
[ 908.963058] eql: event: 6
[ 908.963059] eql: IFF_SLAVE
[ 908.963110] bond0: Releasing active interface eql
[ 908.976168] bond0: Destroying bond bond0
[ 908.976266] bond0 (unregistering): Released all slaves
[ 908.984097] ------------[ cut here ]------------
[ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[ 908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]
Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit f9399814927ad ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: Carol Soto <[email protected]> Signed-off-by: Nikolay Aleksandrov <[email protected]> Fixes: a64d49c3dd50 ("bonding: Manage /proc/net/bonding/ entries from
the netdev events") Tested-by: Carol L Soto <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Get rid of these:
drivers/net/bonding//bond_main.c: In function ‘bond_update_slave_arr’:
drivers/net/bonding//bond_main.c:3754:6: warning: variable
‘slaves_in_agg’ set but not used [-Wunused-but-set-variable]
int slaves_in_agg;
^
CC [M] drivers/net/bonding//bond_3ad.o
drivers/net/bonding//bond_3ad.c: In function
‘ad_marker_response_received’:
drivers/net/bonding//bond_3ad.c:1870:61: warning: parameter ‘marker’
set but not used [-Wunused-but-set-parameter]
static void ad_marker_response_received(struct bond_marker *marker,
^
drivers/net/bonding//bond_3ad.c:1871:19: warning: parameter ‘port’ set
but not used [-Wunused-but-set-parameter]
struct port *port)
^
David S. Miller [Mon, 20 Jul 2015 19:49:11 +0000 (12:49 -0700)]
Merge branch 'bridge-temp-and-perm'
Nikolay Aleksandrov says:
====================
bridge: multicast: temp and perm entries behaviour enhancements
Patch 01 adds a notify when a group is deleted via br_multicast_del_pg()
(on expire, on device delete or on device down).
Patch 02 changes how bridge device and bridge port delete and down/up are
handled. Until now on bridge down all groups were flushed, now only the
temp ones are (same for port), perm entries are flushed only on port or
bridge removal.
====================
bridge: multicast: fix handling of temp and perm entries
When the bridge (or port) is brought down/up flush only temp entries and
leave the perm ones. Flush perm entries only when deleting the bridge
device or the associated port.
Group notifications were not sent when a group expired or was deleted
due to bridge/port device being deleted. So add br_mdb_notify() to
br_multicast_del_pg().
Vivien Didelot [Wed, 15 Jul 2015 14:07:07 +0000 (10:07 -0400)]
net: dsa: mv88e6xxx: fix fid_mask when leaving bridge
The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.
This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.
Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).
Indeed, br0 uses FID 0, and br1 uses FID 3.
After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).
With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
virtio_net: don't require ANY_LAYOUT with VERSION_1
ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.
Daniel Borkmann [Wed, 15 Jul 2015 12:21:42 +0000 (14:21 +0200)]
ebpf: add helper to retrieve net_cls's classid cookie
It would be very useful to retrieve the net_cls's classid from an eBPF
program to allow for a more fine-grained classification, it could be
directly used or in conjunction with additional policies. I.e. docker,
but also tooling such as cgexec, can easily run applications via net_cls
cgroups:
Thus, their respecitve classid cookie of foo can then be looked up on
the egress path to apply further policies. The helper is desigend such
that a non-zero value returns the cgroup id.
Daniel Borkmann [Wed, 15 Jul 2015 12:21:41 +0000 (14:21 +0200)]
cls_cgroup: factor out classid retrieval
Split out retrieving the cgroups net_cls classid retrieval into its
own function, so that it can be reused later on from other parts of
the traffic control subsystem. If there's no skb->sk, then the small
helper returns 0 as well, which in cls_cgroup terms means 'could not
classify'.
enic: allow adaptive coalesce setting for msi/legacy intr
* Allow setting of adaptive coalescing setting for all types of interrupt.
* In msi & legacy intr, we use single interrupt for rx & tx. In this case
tx_coalesce_usecs is invalid. We should use only rx_coalesce_usecs.
Do not display tx_coal values for msi/intx. And do not allow user to set
this as well.
* Driver supports only tx/rx_coalesce_usec and adaptive coalesce settings.
For other values, driver does not return error. So ethtool succeeds for
unsupported values. Introduce enic_coalesce_valid() function to validate
the coalescing values.
* If user requests for coalesce value greater than what adaptor supports,
driver uses the max value. We should at least log this.
enic: add adaptive coalescing intr for intx and msi poll
Adaptive interrupt coalescing is available for msix. This patch adds the support
for msi poll. Interface for adaptive interrupt coalescing is already added in
driver. We just did not enable it for legacy intr & msi.
enic_calc_int_moderation() & enic_set_int_moderation() are defined as static
after enic_poll. Since enic_poll needs it, move both of these function
definitions above enic_poll. No change in functionality.
This causes some of the offsets used in entry.S to overflow their
instruction operand field. To fix this use aghi to create a
dedicated pointer for the thread_struct.
Migrate avr32 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We want to call cpu_idle_poll_ctrl() in shutdown only if we were in
oneshot or resume state earlier. Create another variable to save this
information and check that in shutdown callback.
Joachim Eastwood [Tue, 14 Jul 2015 22:25:26 +0000 (00:25 +0200)]
pinctrl: lpc18xx: fix schmitt trigger setup
The param_val variable is what determines if schmitt
trigger is enabled on a pin or not. A typo here mean
that schmitt trigger was always enabled for standard
and i2c pins.
Subject: pinctrl: imx1-core: Fix debug output in .pin_config_set callback
imx1_pinconf_set assumes that the array of pins in struct
imx1_pinctrl_soc_info can be indexed by pin id to get the
pinctrl_pin_desc for a pin. This used to be correct up to commit 607af165c047 which removed some entries from the array and so made it
wrong to access the array by pin id.
The result of this bug is a wrong pin name in the output for small pin
ids and an oops for the bigger ones.
This patch is the result of a discussion that includes patches by Markus
Pargmann and Chris Ruehl.
Jonathan Bell [Tue, 30 Jun 2015 11:35:39 +0000 (12:35 +0100)]
pinctrl: bcm2835: Clear the event latch register when disabling interrupts
It's possible to hit a race condition if interrupts are generated on a GPIO
pin when the IRQ line in question is being disabled.
If the interrupt is freed, bcm2835_gpio_irq_disable() is called which
disables the event generation sources (edge, level). If an event occurred
between the last disabling of hard IRQs and the write to the event
source registers, a bit would be set in the GPIO event detect register
(GPEDSn) which goes unacknowledged by bcm2835_gpio_irq_handler()
so Linux complains loudly.
There is no per-GPIO mask register, so when disabling GPIO interrupts
write 1 to the relevant bit in GPEDSn to clear out any stale events.
pinctrl: single: ensure pcs irq will not be forced threaded
The PSC IRQ is requested using request_irq() API and as result it can
be forced to be threaded IRQ in RT-Kernel if PCS_QUIRK_HAS_SHARED_IRQ
is enabled for pinctrl domain.
As result, following 'possible irq lock inversion dependency' report
can be seen:
=========================================================
[ INFO: possible irq lock inversion dependency detected ] 3.14.43-rt42-00360-g96ff499-dirty #24 Not tainted
---------------------------------------------------------
irq/369-pinctrl/927 just changed the state of lock:
(&pcs->lock){+.....}, at: [<c0375b54>] pcs_irq_handle+0x48/0x9c
but this lock was taken by another, HARDIRQ-safe lock in the past:
(&irq_desc_lock_class){-.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
Sergei Shtylyov [Thu, 25 Jun 2015 22:40:56 +0000 (01:40 +0300)]
sh-pfc: fix sparse GPIOs for R-Car SoCs
The PFC driver causes the kernel to hang on the R-Car gen2 SoC based boards
when the CPU_ALL_PORT() macro is fixed to reflect the reality, i.e. when the
GPIO space becomes actually sparse. This happens because the _GP_GPIO() macro
includes an indexed initializer which causes the "holes" (array entries filled
with all 0s) between the groups of the existing GPIOs; and the driver can't
cope with that. There seems to be no reason to use the indexed initializer,
so we can remove the index specifier and so avoid the "holes".
Commit a21763a0b1e5a5ab8310f581886d04beadc16616
"pinctrl: nomadik: activate strict mux mode"
put all Nomadik pin controllers to strict mode. This was
not good on the Snowball platform: the muxing of GPIOs to
different pins is done with hogs in the DTS file, and then
these GPIOs are used by offset, relying on hogs to mux the
pins. Since that means the pin controller "owns" the pins
and at the same time we have a GPIO user, this pin controller
is by definition not strict.
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fairly simple fixes: one is a change that causes us to have a very
low queue depth leading to performance issues and the other is a null
deref occasionally in tapes thanks to use after put"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix host max depth checking for the 'queue_depth' sysfs interface
st: null pointer dereference panic caused by use after kref_put by st_open
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2.
Things are looking quite decent at this stage but the recent work on
the FPU support took its toll:
- fix an incorrect overly restrictive ifdef
- select O32 64-bit FP support for O32 binary compatibility
- remove workarounds for Sibyte SB1250 Pass1 parts. There are rare
fixing the workarounds is not worth the effort.
- patch up an outdated and now incorrect comment"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
MIPS: SB1: Remove support for Pass 1 parts.
MIPS: Require O32 FP64 support for MIPS64 with O32 compat
MIPS: asm-offset.c: Patch up various comments refering to the old filename.
Merge branch 'parisc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"A memory leak fix from Christophe Jaillet which was introduced with
kernel 4.0 and which leads to kernel crashes on parisc after 1-3 days"
* 'parisc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: mm: Fix a memory leak related to pmd not attached to the pgd
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
Commit 6134d94923d0 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
added support for 64-bit FPU on a 32-bit MIPS R6 processor but it missed
the 64-bit CPU case leading to FPU failures when requesting FR=1 mode
(which is always the case for MIPS R6 userland) when running a 32-bit
kernel on a 64-bit CPU. We also fix the MIPS R2 case.
After this commit, the 'return' statement in pmd_free is executed in all
cases. Even for pmd that are not attached to the pgd. So 'free_pages'
can never be called anymore, leading to a memory leak.
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A small set of ARM fixes for -rc3, most of them not far off
one-liners, with the exception of fixing the V7 cache invalidation for
incoming SMP processors which was causing problems for SoCFPGA
devices"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix __virt_to_idmap build error on !MMU
ARM: invalidate L1 before enabling coherency
ARM: 8404/1: dma-mapping: fix off-by-one error in bitmap size check
ARM: 8402/1: perf: Don't use of_node after putting it
ARM: 8400/1: use virt_to_idmap to get phys_reset address
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two families of fixes:
- Fix an FPU context related boot crash on newer x86 hardware with
larger context sizes than what most people test. To fix this
without ugly kludges or extensive reverts we had to touch core task
allocator, to allow x86 to determine the task size dynamically, at
boot time.
I've tested it on a number of x86 platforms, and I cross-built it
to a handful of architectures:
... so I hope the cross-arch impact 'none', as intended.
(by Dave Hansen)
- Fix various NMI handling related bugs unearthed by the big asm code
rewrite and generally make the NMI code more robust and more
maintainable while at it. These changes are a bit late in the
cycle, I hope they are still acceptable.
(by Andy Lutomirski)"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu, sched: Introduce CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT and use it on x86
x86/fpu, sched: Dynamically allocate 'struct fpu'
x86/entry/64, x86/nmi/64: Add CONFIG_DEBUG_ENTRY NMI testing code
x86/nmi/64: Make the "NMI executing" variable more consistent
x86/nmi/64: Minor asm simplification
x86/nmi/64: Use DF to avoid userspace RSP confusing nested NMI detection
x86/nmi/64: Reorder nested NMI checks
x86/nmi/64: Improve nested NMI comments
x86/nmi/64: Switch stacks on userspace NMI entry
x86/nmi/64: Remove asm code that saves CR2
x86/nmi: Enable nested do_nmi() handling for 64-bit kernels
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix for a misplaced export that can cause build failures in certain
(rare) Kconfig situations"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Move the export of tick_broadcast_oneshot_control to the proper place
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"A oneliner rq throttling fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Test list head instead of list entry in throttle_cfs_rq()
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus a static key fix fixing /sys/devices/cpu/rdpmc"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Really allow to specify custom CC, AR or LD
perf auxtrace: Fix misplaced check for HAVE_SYNC_COMPARE_AND_SWAP_SUPPORT
perf hists browser: Take the --comm, --dsos, etc filters into account
perf symbols: Store if there is a filter in place
x86, perf: Fix static_key bug in load_mm_cr4()
tools: Copy lib/hweight.c from the kernel sources
perf tools: Fix the detached tarball wrt rbtree copy
perf thread_map: Fix the sizeof() calculation for map entries
tools lib: Improve clean target
perf stat: Fix shadow declaration of close
perf tools: Fix lockup using 32-bit compat vdso
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Misc irq fixes:
- two driver fixes
- a Xen regression fix
- a nested irq thread crash fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gicv3-its: Fix mapping of LPIs to collections
genirq: Prevent resend to interrupts marked IRQ_NESTED_THREAD
genirq: Revert sparse irq locking around __cpu_up() and move it to x86 for now
gpio/davinci: Fix race in installing chained irq handler
* emailed patches from Andrew Morton <[email protected]>: (25 commits)
lib/decompress: set the compressor name to NULL on error
mm/cma_debug: correct size input to bitmap function
mm/cma_debug: fix debugging alloc/free interface
mm/page_owner: set correct gfp_mask on page_owner
mm/page_owner: fix possible access violation
fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
/proc/$PID/cmdline: fixup empty ARGV case
dma-debug: skip debug_dma_assert_idle() when disabled
hexdump: fix for non-aligned buffers
checkpatch: fix long line messages about patch context
mm: clean up per architecture MM hook header files
MAINTAINERS: uclinux-h8-devel is moderated for non-subscribers
mailmap: update Sudeep Holla's email id
Update Viresh Kumar's email address
mm, meminit: suppress unused memory variable warning
configfs: fix kernel infoleak through user-controlled format string
include, lib: add __printf attributes to several function prototypes
s390/hugetlb: add hugepages_supported define
mm: hugetlb: allow hugepages_supported to be architecture specific
revert "s390/mm: make hugepages_supported a boot time decision"
...
Merge branch 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are all from Filipe, and cover a few problems we've had reported
on the list recently (along with ones he found on his own)"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix file corruption after cloning inline extents
Btrfs: fix order by which delayed references are run
Btrfs: fix list transaction->pending_ordered corruption
Btrfs: fix memory leak in the extent_same ioctl
Btrfs: fix shrinking truncate when the no_holes feature is enabled
Merge tag 'rtc-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull rtc fixes from Alexandre Belloni:
"A few fixes for the RTC susbsystem for 4.2.
The mt6397 driver was introduce in 4.2 so it is worth fixing before
the final release. I though the compilation warning for armada38x was
fixed by akpm in commit f98b733e93e0 ("rtc-armada38x.c: remove unused
local `flags'") but he actually missed some occurrences of the
variables. Since I received 4 patches for that, I think we can
include it now.
Summary:
- fix mt6397 wakealarm creation
- remove a compilation warning for armada38x that was forgotten"
* tag 'rtc-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: armada38x: Remove unused variable from armada38x_rtc_set_time()
rtc: mt6397: enable wakeup before registering rtc device
Merge tag 'dm-4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- revert a request-based DM core change that caused IO latency to
increase and adversely impact both throughput and system load
- fix for a use after free bug in DM core's device cleanup
- a couple DM btree removal fixes (used by dm-thinp)
- a DM thinp fix for order-5 allocation failure
- a DM thinp fix to not degrade to read-only metadata mode when in
out-of-data-space mode for longer than the 'no_space_timeout'
- fix a long-standing oversight in both dm-thinp and dm-cache by now
exporting 'needs_check' in status if it was set in metadata
- fix an embarrassing dm-cache busy-loop that caused worker threads to
eat cpu even if no IO was actively being issued to the cache device
* tag 'dm-4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: avoid calls to prealloc_free_structs() if possible
dm cache: avoid preallocation if no work in writeback_some_dirty_blocks()
dm cache: do not wake_worker() in free_migration()
dm cache: display 'needs_check' in status if it is set
dm thin: display 'needs_check' in status if it is set
dm thin: stay in out-of-data-space mode once no_space_timeout expires
dm: fix use after free crash due to incorrect cleanup sequence
Revert "dm: only run the queue on completion if congested or no requests pending"
dm btree: silence lockdep lock inversion in dm_btree_del()
dm thin: allocate the cell_sort_array dynamically
dm btree remove: fix bug in redistribute3
igb: Fix i354 88E1112 PHY on RCC boards using AutoMediaDetect
e1000_check_for_link_media_swap() checks PHY page 0 for copper and PHY
page 1 for "other" (fiber) link. The switch back from page 1 to page 0
happened too soon, before e1000_check_for_link_82575() is executed, and
link on fiber (other) was never detected. Check for link while still on
the proper PHY page.
Fan Du [Wed, 29 Apr 2015 02:57:41 +0000 (10:57 +0800)]
ixgbe: Don't report flow director filter's status
For two reasons I want to disable this:
1. Not any part actually check the report status(Alexander Duyck)
2. To report hash value of a packet to stack,
RSS -> 32bits hash value
Perfect match fdir filter -> 13bits hash value
Hashed-based fdir filter -> 31bits hash value
fdir filter might hash on masked tuples for IP address,
so it's still not desirable for usage.
Alexander Duyck [Thu, 23 Apr 2015 04:49:32 +0000 (21:49 -0700)]
ixgbevf: fold ixgbevf_pull_tail into ixgbevf_add_rx_frag
This change folds the ixgbevf_pull_tail call into ixgbevf_add_rx_frag. The
advantage to doing this is that the fragment doesn't have to be modified
after it is added to the skb.
Alexander Duyck [Thu, 23 Apr 2015 04:49:17 +0000 (21:49 -0700)]
igb: Pull timestamp from fragment before adding it to skb
This change makes it so that we pull the timestamp from the fragment before
we add it to the skb. By doing this we can avoid a possible issue in which
the fragment can possibly be less than IGB_RX_HDR_LEN due to the timestamp
being pulled after the copybreak check.
While making this change I realized we could also pull the rest of the
igb_pull_tail function into igb_add_rx_frag since in the case of igb,
unlike ixgbe, we are able to unmap the entire buffer before calling
add_rx_frag so merging the two allows for sharing of code between the two
merged functions.
projects / linux.git / log