Marek Szyprowski [Tue, 30 Apr 2024 18:46:56 +0000 (20:46 +0200)]
clk: samsung: Revert "clk: Use device_get_match_data()"
device_get_match_data() function should not be used on the device other
than the one matched to the given driver, because it always returns the
match_data of the matched driver. In case of exynos-clkout driver, the
original code matches the OF IDs on the PARENT device, so replacing it
with of_device_get_match_data() broke the driver.
This has been already pointed once in commit 2bc5febd05ab ("clk: samsung:
Revert "clk: samsung: exynos-clkout: Use of_device_get_match_data()"").
To avoid further confusion, add a comment about this special case, which
requires direct of_match_device() call to pass custom IDs array.
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fix from Paolo Bonzini:
"A pretty straightforward fix for a NULL pointer dereference, plus the
accompanying reproducer"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: selftests: Add test for uaccesses to non-existent vgic-v2 CPUIF
KVM: arm64: vgic-v2: Check for non-NULL vCPU in vgic_v2_parse_attr()
Input: amimouse - mark driver struct with __refdata to prevent section mismatch
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent the following section mismatch warning
usb: typec: tcpm: Check for port partner validity before consuming it
typec_register_partner() does not guarantee partner registration
to always succeed. In the event of failure, port->partner is set
to the error value or NULL. Given that port->partner validity is
not checked, this results in the following crash:
Unable to handle kernel NULL pointer dereference at virtual address xx
pc : run_state_machine+0x1bc8/0x1c08
lr : run_state_machine+0x1b90/0x1c08
..
Call trace:
run_state_machine+0x1bc8/0x1c08
tcpm_state_machine_work+0x94/0xe4
kthread_worker_fn+0x118/0x328
kthread+0x1d0/0x23c
ret_from_fork+0x10/0x20
To prevent the crash, check for port->partner validity before
derefencing it in all the call sites.
usb: typec: tcpm: enforce ready state when queueing alt mode vdm
Before sending Enter Mode for an Alt Mode, there is a gap between Discover
Modes and the Alt Mode driver queueing the Enter Mode VDM for the port
partner to send a message to the port.
If this message results in unregistering Alt Modes such as in a DR_SWAP,
then the following deadlock can occur with respect to the DisplayPort Alt
Mode driver:
1. The DR_SWAP state holds port->lock. Unregistering the Alt Mode driver
results in a cancel_work_sync() that waits for the current dp_altmode_work
to finish.
2. dp_altmode_work makes a call to tcpm_altmode_enter. The deadlock occurs
because tcpm_queue_vdm_unlock attempts to hold port->lock.
Before attempting to grab the lock, ensure that the port is in a state
vdm_run_state_machine can run in. Alt Mode unregistration will not occur
in these states.
usb: typec: tcpm: unregister existing source caps before re-registration
Check and unregister existing source caps in tcpm_register_source_caps
function before registering new ones. This change fixes following
warning when port partner resends source caps after negotiating PD contract
for the purpose of re-negotiation.
[ 343.135030][ T151] sysfs: cannot create duplicate filename '/devices/virtual/usb_power_delivery/pd1/source-capabilities'
[ 343.135071][ T151] Call trace:
[ 343.135076][ T151] dump_backtrace+0xe8/0x108
[ 343.135099][ T151] show_stack+0x18/0x24
[ 343.135106][ T151] dump_stack_lvl+0x50/0x6c
[ 343.135119][ T151] dump_stack+0x18/0x24
[ 343.135126][ T151] sysfs_create_dir_ns+0xe0/0x140
[ 343.135137][ T151] kobject_add_internal+0x228/0x424
[ 343.135146][ T151] kobject_add+0x94/0x10c
[ 343.135152][ T151] device_add+0x1b0/0x4c0
[ 343.135187][ T151] device_register+0x20/0x34
[ 343.135195][ T151] usb_power_delivery_register_capabilities+0x90/0x20c
[ 343.135209][ T151] tcpm_pd_rx_handler+0x9f0/0x15b8
[ 343.135216][ T151] kthread_worker_fn+0x11c/0x260
[ 343.135227][ T151] kthread+0x114/0x1bc
[ 343.135235][ T151] ret_from_fork+0x10/0x20
[ 343.135265][ T151] kobject: kobject_add_internal failed for source-capabilities with -EEXIST, don't try to register things with the same name in the same directory.
usb: typec: tcpm: clear pd_event queue in PORT_RESET
When a Fast Role Swap control message attempt results in a transition
to ERROR_RECOVERY, the TCPC can still queue a TCPM_SOURCING_VBUS event.
If the event is queued but processed after the tcpm_reset_port() call
in the PORT_RESET state, then the following occurs:
1. tcpm_reset_port() calls tcpm_init_vbus() to reset the vbus sourcing and
sinking state
2. tcpm_pd_event_handler() turns VBUS on before the port is in the default
state.
3. The port resolves as a sink. In the SNK_DISCOVERY state,
tcpm_set_charge() cannot set vbus to charge.
Clear pd events within PORT_RESET to get rid of non-applicable events.
drm/vmwgfx: Fix invalid reads in fence signaled events
Correctly set the length of the drm_event to the size of the structure
that's actually used.
The length of the drm_event was set to the parent structure instead of
to the drm_vmw_event_fence which is supposed to be read. drm_read
uses the length parameter to copy the event to the user space thus
resuling in oob reads.
Lyude Paul [Mon, 29 Apr 2024 18:23:09 +0000 (14:23 -0400)]
drm/nouveau/gsp: Use the sg allocator for level 2 of radix3
Currently we allocate all 3 levels of radix3 page tables using
nvkm_gsp_mem_ctor(), which uses dma_alloc_coherent() for allocating all of
the relevant memory. This can end up failing in scenarios where the system
has very high memory fragmentation, and we can't find enough contiguous
memory to allocate level 2 of the page table.
Currently, this can result in runtime PM issues on systems where memory
fragmentation is high - as we'll fail to allocate the page table for our
suspend/resume buffer:
Luckily, we don't actually need to allocate coherent memory for the page
table thanks to being able to pass the GPU a radix3 page table for
suspend/resume data. So, let's rewrite nvkm_gsp_radix3_sg() to use the sg
allocator for level 2. We continue using coherent allocations for lvl0 and
1, since they only take a single page.
V2:
* Don't forget to actually jump to the next scatterlist when we reach the
end of the scatterlist we're currently on when writing out the page table
for level 2
We hit this when trying to initialize firmware of type
NVKM_FIRMWARE_IMG_DMA because we allocate our memory with
dma_alloc_coherent, and DMA allocations can't be turned back into memory
pages - which a scatterlist needs in order to map them.
So, fix this by allocating the memory with vmalloc instead().
V2:
* Fixup explanation as the prior one was bogus
Unfortunately both Lenovo Legion Pro 7 16ARX8H and Legion 7i 16IAX7
got the very same PCI SSID while the hardware implementations are
completely different (the former is with TI TAS2781 codec while the
latter is with Cirrus CS35L41 codec). The former model got broken by
the recent fix for the latter model.
For addressing the regression, check the codec SSID and apply the
proper quirk for each model now.
Kailang Yang [Tue, 30 Apr 2024 09:15:53 +0000 (17:15 +0800)]
ALSA: hda/realtek - Set GPIO3 to default at S4 state for Thinkpad with ALC1318
There is a chance of damaging the IC when S4 resume.
Add safe mode for no stream to disable GPIO3.
Thinkpad with ALC1318 platform need to add this workaround.
Merge tag 'platform-drivers-x86-v6.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fix from Ilpo Järvinen:
- Add Grand Ridge to HPM CPU list
* tag 'platform-drivers-x86-v6.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: ISST: Add Grand Ridge to HPM CPU list
Alan Stern [Tue, 30 Apr 2024 14:33:48 +0000 (10:33 -0400)]
usb: Fix regression caused by invalid ep0 maxpacket in virtual SuperSpeed device
A virtual SuperSpeed device in the FreeBSD BVCP package
(https://bhyve.npulse.net/) presents an invalid ep0 maxpacket size of 256.
It stopped working with Linux following a recent commit because now we
check these sizes more carefully than before.
Fix this regression by using the bMaxpacketSize0 value in the device
descriptor for SuperSpeed or faster devices, even if it is invalid. This
is a very simple-minded change; we might want to check more carefully for
values that actually make some sense (for instance, no smaller than 64).
Testing ohci functionality with qemu's pci-ohci emulation often results
in ohci interface stalls, resulting in hung task timeouts.
The problem is caused by lost interrupts between the emulation and the
Linux kernel code. Additional interrupts raised while the ohci interrupt
handler in Linux is running and before the handler clears the interrupt
status are not handled. The fix for a similar problem in ehci suggests
that the problem is likely caused by edge-triggered MSI interrupts. See
commit 0b60557230ad ("usb: ehci: Prevent missed ehci interrupts with
edge-triggered MSI") for details.
Ensure that the ohci interrupt code handles all pending interrupts before
returning to solve the problem.
Merge tag 'pinctrl-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix a double-free in the pinctrl_enable() errorpath
- Fix a refcount leak in pinctrl_dt_to_map()
- Fix selecting the GPIO pin control state and the UART3 pin config
group in the Intel Baytrail driver
- Fix readback of schmitt trigger status in the Mediatek Paris driver,
along with some semantic pin config issues in this driver
- Fix a pin suffix typo in the Meson A1 driver
- Fix an erroneous register offset in he Aspeed G6 driver
- Fix an inconsistent lock state and the interrupt type on resume in
the Renesas RZG2L driver
- Fix some minor confusion in the Renesas DT bindings
* tag 'pinctrl-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: renesas: rzg2l: Configure the interrupt type on resume
pinctrl: devicetree: fix refcount leak in pinctrl_dt_to_map()
pinctrl: baytrail: Add pinconf group for uart3
pinctrl: baytrail: Fix selecting gpio pinctrl state
pinctrl: mediatek: paris: Rework support for PIN_CONFIG_{INPUT,OUTPUT}_ENABLE
pinctrl: mediatek: paris: Fix PIN_CONFIG_INPUT_SCHMITT_ENABLE readback
pinctrl: core: delete incorrect free in pinctrl_enable()
pinctrl/meson: fix typo in PDM's pin name
pinctrl: pinctrl-aspeed-g6: Fix register offset for pinconf of GPIOR-T
pinctrl: renesas: rzg2l: Execute atomically the interrupt configuration
dt-bindings: pinctrl: renesas,rzg2l-pinctrl: Allow 'input' and 'output-enable' properties
This patchset fixes 2 problems on TDM which both find a solution
by properly implementing the .trigger() callback for the TDM backend.
ATM, enabling the TDM formatters is done by the .prepare() callback
because handling the formatter is slow due to necessary calls to CCF.
The first problem affects the TDMIN. Because .prepare() is called on DPCM
backend first, the formatter are started before the FIFOs and this may
cause a random channel shifts if the TDMIN use multiple lanes with more
than 2 slots per lanes. Using trigger() allows to set the FE/BE order,
solving the problem.
There has already been an attempt to fix this 3y ago [1] and reverted [2]
It triggered a 'sleep in irq' error on the period IRQ. The solution is
to just use the bottom half of threaded IRQ. This is patch #1. Patch #2
and #3 remain mostly the same as 3y ago.
For TDMOUT, the problem is on pause. ATM pause only stops the FIFO and
the TDMOUT just starves. When it does, it will actually repeat the last
sample continuously. Depending on the platform, if there is no high-pass
filter on the analog path, this may translate to a constant position of
the speaker membrane. There is no audible glitch but it may damage the
speaker coil.
Properly stopping the TDMOUT in pause solves the problem. There is
behaviour change associated with that fix. Clocks used to be continuous
on pause because of the problem above. They will now be gated on pause by
default, as they should. The last change introduce the proper support for
continuous clocks, if needed.
btrfs: set correct ram_bytes when splitting ordered extent
[BUG]
When running generic/287, the following file extent items can be
generated:
item 16 key (258 EXTENT_DATA 2682880) itemoff 15305 itemsize 53
generation 9 type 1 (regular)
extent data disk byte 1378414592 nr 462848
extent data offset 0 nr 462848 ram 2097152
extent compression 0 (none)
Note that file extent item is not a compressed one, but its ram_bytes is
way larger than its disk_num_bytes.
According to btrfs on-disk scheme, ram_bytes should match disk_num_bytes
if it's not a compressed one.
[CAUSE]
Since commit b73a6fd1b1ef ("btrfs: split partial dio bios before
submit"), for partial dio writes, we would split the ordered extent.
However the function btrfs_split_ordered_extent() doesn't update the
ram_bytes even it has already shrunk the disk_num_bytes.
Originally the function btrfs_split_ordered_extent() is only introduced
for zoned devices in commit d22002fd37bd ("btrfs: zoned: split ordered
extent when bio is sent"), but later commit b73a6fd1b1ef ("btrfs: split
partial dio bios before submit") makes non-zoned btrfs affected.
Thankfully for un-compressed file extent, we do not really utilize the
ram_bytes member, thus it won't cause any real problem.
[FIX]
Also update btrfs_ordered_extent::ram_bytes inside
btrfs_split_ordered_extent().
Merge tag 'fpga-for-6.9-final' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into char-misc-linus
Xu writes:
FPGA Manager changes for 6.9-final
DFL
- Peter adds PCI ID table for Intel D5005 Stratix 10 FPGA card
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our fixes branch)
Signed-off-by: Xu Yilun <[email protected]>
* tag 'fpga-for-6.9-final' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
fpga: dfl-pci: add PCI subdevice ID for Intel D5005 card
Thomas Gleixner [Thu, 25 Apr 2024 22:30:36 +0000 (00:30 +0200)]
x86/apic: Don't access the APIC when disabling x2APIC
With 'iommu=off' on the kernel command line and x2APIC enabled by the BIOS
the code which disables the x2APIC triggers an unchecked MSR access error:
RDMSR from 0x802 at rIP: 0xffffffff94079992 (native_apic_msr_read+0x12/0x50)
This is happens because default_acpi_madt_oem_check() selects an x2APIC
driver before the x2APIC is disabled.
When the x2APIC is disabled because interrupt remapping cannot be enabled
due to 'iommu=off' on the command line, x2apic_disable() invokes
apic_set_fixmap() which in turn tries to read the APIC ID. This triggers
the MSR warning because x2APIC is disabled, but the APIC driver is still
x2APIC based.
Prevent that by adding an argument to apic_set_fixmap() which makes the
APIC ID read out conditional and set it to false from the x2APIC disable
path. That's correct as the APIC ID has already been read out during early
discovery.
Merge tag 'wq-for-6.9-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"Two doc update patches and the following three fixes:
- On single node systems, the default pool is used but the
node_nr_active for the default pool was set to min_active. This
effectively limited the max concurrency of unbound pools on single
node systems to 8 causing performance regressions on some
workloads. Fixed by setting the default pool's node_nr_active to
max_active.
- wq_update_node_max_active() could trigger divide-by-zero if the
intersection between the allowed CPUs for an unbound workqueue and
online CPUs becomes empty.
- When kick_pool() was trying to repatriate a worker to a CPU in its
pod by setting task->wake_cpu, it didn't consider whether the CPU
being selected is online or not which obviously can lead to
subobtimal behaviors. On s390, this triggered a crash in arch code.
The workqueue patch removes the gross misbehavior but doesn't fix
the crash completely as there's a race window in which CPUs can go
down after wake_cpu is set. Need to decide whether the fix should
be on the core or arch side"
* tag 'wq-for-6.9-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Fix divide error in wq_update_node_max_active()
workqueue: The default node_nr_active should have its max set to max_active
workqueue: Fix selection of wake_cpu in kick_pool()
docs/zh_CN: core-api: Update translation of workqueue.rst to 6.9-rc1
Documentation/core-api: Update events_freezable_power references.
Stephen Boyd [Mon, 29 Apr 2024 21:59:35 +0000 (14:59 -0700)]
Merge tag 'sunxi-clk-fixes-for-6.9-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clk driver fixes from Jernej Skrabec:
- fix H6 CPU rate change via reparenting
- set A64 MIPI PLL min & max rate
* tag 'sunxi-clk-fixes-for-6.9-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a64: Set minimum and maximum rate for PLL-MIPI
clk: sunxi-ng: common: Support minimum and maximum rate
clk: sunxi-ng: h6: Reparent CPUX during PLL CPUX rate change
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Minor core fix to prevent the sd driver printing the stream count
every time we rescan and instead print only if it's changed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Only print updates to permanent stream count
Merge tag 'nfs-for-6.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
- Fix an Oops in xs_tcp_tls_setup_socket
- Fix an Oops due to missing error handling in nfs_net_init()
* tag 'nfs-for-6.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: Handle error of rpc_proc_register() in nfs_net_init().
SUNRPC: add a missing rpc_stat for TCP TLS
Currently, we allocate a lbuf-sized kernel buffer and copy lbuf from
userspace to that buffer. Later, we use scanf on this buffer but we don't
ensure that the string is terminated inside the buffer, this can lead to
OOB read when using scanf. Fix this issue by using memdup_user_nul instead.
Dave Jiang [Fri, 26 Apr 2024 22:47:56 +0000 (15:47 -0700)]
cxl: Fix cxl_endpoint_get_perf_coordinate() support for RCH
Robert reported the following when booting a CXL host with Restricted CXL
Host (RCH) topology:
[ 39.815379] cxl_acpi ACPI0017:00: not a cxl_port device
[ 39.827123] WARNING: CPU: 46 PID: 1754 at drivers/cxl/core/port.c:592 to_cxl_port+0x56/0x70 [cxl_core]
... plus some related subsequent NULL pointer dereference:
The iterator to walk the PCIe path did not account for RCH topology.
However RCH does not support hotplug and the memory exported by the
Restricted CXL Device (RCD) should be covered by HMAT and therefore no
access_coordinate is needed. Add check to see if the endpoint device is
RCD and skip calculation.
Also add a call to cxl_endpoint_get_perf_coordinates() in cxl_test in order
to exercise the topology iterator. The dev_is_pci() check added is to help
with this test and should be harmless for normal operation.
Merge tag 'erofs-for-6.9-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"Three fixes related to EROFS fscache mode. The most important two
patches fix calling kill_block_super() in bdev-based mode instead of
kill_anon_super(). The remaining patch is an informative one.
Summary:
- Better error message when prepare_ondemand_read failed
- Fix unmount of bdev-based mode if CONFIG_EROFS_FS_ONDEMAND is on"
* tag 'erofs-for-6.9-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: reliably distinguish block based and fscache mode
erofs: get rid of erofs_fs_context
erofs: modify the error message when prepare_ondemand_read failed
The SOF driver is selected whenever specific I2C/I2S HIDs are reported
as 'present' in the ACPI DSDT. In some cases, an HID is reported but
the hardware does not actually rely on I2C/I2S. This false positive
leads to an invalid selection of the SOF driver and as a result an
invalid topology is loaded.
This patch hardens the detection with a check that the NHLT table is
consistent with the report of an I2S-based codec in DSDT. This table
should expose at least one SSP endpoint configured for an I2S-codec
connection.
Tested on Huawei Matebook D14 (NBLB-WAX9N) using an HDaudio codec with
an invalid ES8336 ACPI HID reported:
[ 7.858249] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380
[ 7.858312] snd_hda_intel 0000:00:1f.3: snd_intel_dsp_find_config: no valid SSP found for HID ESSX8336, skipped
Amlogic sound cards do create a lot of pcm interfaces, possibly more than
8. Some pcm interfaces are internal (like DPCM backends and c2c) and not
exposed to userspace.
Those interfaces still increase the number passed to snd_find_free_minor(),
which eventually exceeds 8 causing -EBUSY error on card registration if
CONFIG_SND_DYNAMIC_MINORS=n and the interface is exposed to userspace.
select CONFIG_SND_DYNAMIC_MINORS for Amlogic cards to avoid the problem.
ASoC: meson: axg-tdm-interface: manage formatters in trigger
So far, the formatters have been reset/enabled using the .prepare()
callback. This was done in this callback because walking the formatters use
a mutex. A mutex is used because formatter handling require dealing
possibly slow clock operation.
With the support of non-atomic, .trigger() callback may be used which also
allows to properly enable and disable formatters on start but also
pause/resume.
This solve a random shift on TDMIN as well repeated samples on for TDMOUT.
Non atomic operations need to be performed in the trigger callback
of the TDM interfaces. Those are BEs but what matters is the nonatomic
flag of the FE in the DPCM context. Just set nonatomic for everything so,
at least, what is done is clear.
ASoC: meson: axg-fifo: use threaded irq to check periods
With the AXG audio subsystem, there is a possible random channel shift on
TDM capture, when the slot number per lane is more than 2, and there is
more than one lane used.
The problem has been there since the introduction of the axg audio support
but such scenario is pretty uncommon. This is why there is no loud
complains about the problem.
Solving the problem require to make the links non-atomic and use the
trigger() callback to start FEs and BEs in the appropriate order.
This was tried in the past and reverted because it caused the block irq to
sleep while atomic. However, instead of reverting, the solution is to call
snd_pcm_period_elapsed() in a non atomic context.
tracing/probes: Fix memory leak in traceprobe_parse_probe_arg_body()
If traceprobe_parse_probe_arg_body() failed to allocate 'parg->fmt',
it jumps to the label 'out' instead of 'fail' by mistake.In the result,
the buffer 'tmp' is not freed in this case and leaks its memory.
David S. Miller [Mon, 29 Apr 2024 12:39:15 +0000 (13:39 +0100)]
Merge branch 'vxlan-stats'
Guillaume Nault says:
====================
vxlan: Fix vxlan counters.
Like most virtual devices, vxlan needs special care when updating its
netdevice counters. This is done in patch 1. Patch 2 just adds a
missing VNI counter update (found while working on patch 1).
====================
vxlan: Add missing VNI filter counter update in arp_reduce().
VXLAN stores per-VNI statistics using vxlan_vnifilter_count().
These statistics were not updated when arp_reduce() failed its
pskb_may_pull() call.
Use vxlan_vnifilter_count() to update the VNI counter when that
happens.
Fixes: 4095e0e1328a ("drivers: vxlan: vnifilter: per vni stats") Signed-off-by: Guillaume Nault <[email protected]> Signed-off-by: David S. Miller <[email protected]>
VXLAN devices update their stats locklessly. Therefore these counters
should either be stored in per-cpu data structures or the updates
should be done using atomic increments.
Since the net_device_core_stats infrastructure is already used in
vxlan_rcv(), use it for the other rx_dropped and tx_dropped counter
updates. Update the other counters atomically using DEV_STATS_INC().
firewire: ohci: fulfill timestamp for some local asynchronous transaction
1394 OHCI driver generates packet data for the response subaction to the
request subaction to some local registers. In the case, the driver should
assign timestamp to them by itself.
This commit fulfills the timestamp for the subaction.
firewire: nosy: ensure user_length is taken into account when fetching packet contents
Ensure that packet_buffer_get respects the user_length provided. If
the length of the head packet exceeds the user_length, packet_buffer_get
will now return 0 to signify to the user that no data were read
and a larger buffer size is required. Helps prevent user space overflows.
x86/sev: Add callback to apply RMP table fixups for kexec
Handle cases where the RMP table placement in the BIOS is not 2M aligned
and the kexec-ed kernel could try to allocate from within that chunk
which then causes a fatal RMP fault.
As seen here in the e820 memory map, the end range of the RMP table is not
aligned to 2MB and not reserved but it is usable as RAM.
Subsequently, kexec -s (KEXEC_FILE_LOAD syscall) loads it's purgatory
code and boot_param, command line and other setup data into this RAM
region as seen in the kexec logs below, which leads to fatal RMP fault
during kexec boot.
Check if RMP table start and end physical range in the e820 tables are
not aligned to 2MB and in that case map this range to reserved in all
the three e820 tables.
Thomas Weißschuh [Thu, 11 Apr 2024 21:33:51 +0000 (23:33 +0200)]
misc/pvpanic-pci: register attributes via pci_driver
In __pci_register_driver(), the pci core overwrites the dev_groups field of
the embedded struct device_driver with the dev_groups from the outer
struct pci_driver unconditionally.
Set dev_groups in the pci_driver to make sure it is used.
This was broken since the introduction of pvpanic-pci.
Add a new API helper e820__range_update_table() with which to update an
arbitrary e820 table. Move all current users of
e820__range_update_kexec() to this new helper.
This series fixes the qede driver, so that
qede_parse_flow_attr() and it's subfunctions
doesn't get their error codes overruled
(ie. turning -EOPNOTSUPP into -EINVAL).
---
I have two more patches along the same lines,
but they are not yet causing any issues,
so I have them destined for net-next.
(those are for qede_flow_spec_validate_unused()
and qede_flow_parse_ports().)
After that I have a series for converting to
extack + the final one for validating control
flags.
====================
net: qede: use return from qede_parse_flow_attr() for flow_spec
In qede_flow_spec_to_rule(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced qede_flow_spec_to_rule(),
and this call to qede_parse_flow_attr(), it looks
like it just duplicated how it was already used.
Only compile tested.
Fixes: 37c5d3efd7f8 ("qede: use ethtool_rx_flow_rule() to remove duplicated parser code") Signed-off-by: Asbjørn Sloth Tønnesen <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: qede: use return from qede_parse_flow_attr() for flower
In qede_add_tc_flower_fltr(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced these functions.
Only compile tested.
Fixes: 2ce9c93eaca6 ("qede: Ingress tc flower offload (drop action) support.") Signed-off-by: Asbjørn Sloth Tønnesen <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: qede: sanitize 'rc' in qede_add_tc_flower_fltr()
Explicitly set 'rc' (return code), before jumping to the
unlock and return path.
By not having any code depend on that 'rc' remains at
it's initial value of -EINVAL, then we can re-use 'rc' for
the return code of function calls in subsequent patches.
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
net: bcmgenet: synchronize use of bcmgenet_set_rx_mode()
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Barry Song [Tue, 19 Mar 2024 01:09:20 +0000 (14:09 +1300)]
xtensa: remove redundant flush_dcache_page and ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE macros
xtensa's flush_dcache_page() can be a no-op sometimes. There is a
generic implementation for this case in include/asm-generic/
cacheflush.h.
#ifndef ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE
static inline void flush_dcache_page(struct page *page)
{
}
So remove the superfluous flush_dcache_page() definition, which also
helps silence potential build warnings complaining the page variable
passed to flush_dcache_page() is not used.
In file included from crypto/scompress.c:12:
include/crypto/scatterwalk.h: In function 'scatterwalk_pagedone':
include/crypto/scatterwalk.h:76:30: warning: variable 'page' set but not used [-Wunused-but-set-variable]
76 | struct page *page;
| ^~~~
crypto/scompress.c: In function 'scomp_acomp_comp_decomp':
>> crypto/scompress.c:174:38: warning: unused variable 'dst_page' [-Wunused-variable]
174 | struct page *dst_page = sg_page(req->dst);
|
The issue was originally reported on LoongArch by kernel test
robot (Huacai fixed it on LoongArch), then reported by Guenter
and me on xtensa.
This patch also removes lots of redundant macros which have
been defined by asm-generic/cacheflush.h.
The rcu quiescent state is reported in the rcu-read critical section, so
the lockdep warning is triggered.
Fix this by splitting out the inner working of __do_softirq() into a helper
function which takes an argument to distinguish between ksoftirqd task
context and interrupted context and invoke it from the relevant call sites
with the proper context information and use that for the conditional
invocation of rcu_softirq_qs().
Merge tag 'sched-urgent-2024-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
- Fix EEVDF corner cases
- Fix two nohz_full= related bugs that can cause boot crashes
and warnings
* tag 'sched-urgent-2024-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/isolation: Fix boot crash when maxcpus < first housekeeping CPU
sched/isolation: Prevent boot crash when the boot CPU is nohz_full
sched/eevdf: Prevent vlag from going out of bounds in reweight_eevdf()
sched/eevdf: Fix miscalculation in reweight_entity() when se is not curr
sched/eevdf: Always update V if se->on_rq when reweighting
Merge tag 'x86-urgent-2024-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Make the CPU_MITIGATIONS=n interaction with conflicting
mitigation-enabling boot parameters a bit saner.
- Re-enable CPU mitigations by default on non-x86
- Fix TDX shared bit propagation on mprotect()
- Fix potential show_regs() system hang when PKE initialization
is not fully finished yet.
- Add the 0x10-0x1f model IDs to the Zen5 range
- Harden #VC instruction emulation some more
* tag 'x86-urgent-2024-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Ignore "mitigations" kernel parameter if CPU_MITIGATIONS=n
cpu: Re-enable CPU mitigations by default for !X86 architectures
x86/tdx: Preserve shared bit on mprotect()
x86/cpu: Fix check for RDPKRU in __show_regs()
x86/CPU/AMD: Add models 0x10-0x1f to the Zen5 range
x86/sev: Check for MWAITX and MONITORX opcodes in the #VC handler
erofs: reliably distinguish block based and fscache mode
When erofs_kill_sb() is called in block dev based mode, s_bdev may not
have been initialised yet, and if CONFIG_EROFS_FS_ONDEMAND is enabled,
it will be mistaken for fscache mode, and then attempt to free an anon_dev
that has never been allocated, triggering the following warning:
============================================
ida_free called for id=0 which is not allocated.
WARNING: CPU: 14 PID: 926 at lib/idr.c:525 ida_free+0x134/0x140
Modules linked in:
CPU: 14 PID: 926 Comm: mount Not tainted 6.9.0-rc3-dirty #630
RIP: 0010:ida_free+0x134/0x140
Call Trace:
<TASK>
erofs_kill_sb+0x81/0x90
deactivate_locked_super+0x35/0x80
get_tree_bdev+0x136/0x1e0
vfs_get_tree+0x2c/0xf0
do_new_mount+0x190/0x2f0
[...]
============================================
Now when erofs_kill_sb() is called, erofs_sb_info must have been
initialised, so use sbi->fsid to distinguish between the two modes.
Baokun Li [Fri, 19 Apr 2024 12:36:10 +0000 (20:36 +0800)]
erofs: get rid of erofs_fs_context
Instead of allocating the erofs_sb_info in fill_super() allocate it during
erofs_init_fs_context() and ensure that erofs can always have the info
available during erofs_kill_sb(). After this erofs_fs_context is no longer
needed, replace ctx with sbi, no functional changes.
ALSA: emu10k1: make E-MU FPGA writes potentially more reliable
We did not delay after the second strobe signal, so another immediately
following access could potentially corrupt the written value.
This is a purely speculative fix with no supporting evidence, but after
taking out the spinlocks around the writes, it seems plausible that a
modern processor could be actually too fast. Also, it's just cleaner to
be consistent.
A side effect of making the dock monitoring interrupt-driven was that
we'd be very quick to program a freshly connected dock. However, for
unclear reasons, the dock does not work when we do that - despite the
FPGA netlist upload going just fine. We work around this by adding a
delay before programming the dock; for safety, the value is several
times as much as was determined empirically.
Note that a badly timed dock hot-plug would have triggered the problem
even before the referenced commit - but now it would happen 100% instead
of about 3% of the time, thus making it impossible to work around by
re-plugging.
ALSA: emu10k1: use mutex for E-MU FPGA access locking
The FPGA access through the GPIO port does not interfere with other
sound processor register access, so there is no need to subject it to
emu_lock. And after moving all FPGA access out of the interrupt handler,
it does not need to be IRQ-safe, either.
What's more, attaching the dock causes a firmware upload, which takes
several seconds. We really don't want to disable IRQs for this long, and
even less also have someone else spin with IRQs disabled waiting for us.
Therefore, use a mutex for FPGA access locking.
This makes the code somewhat more noisy, as we need to wrap bigger
sections into the mutex, as it needs to enclose the spinlocks.
The latter has the "side effect" of fixing dock FPGA programming in a
corner case: a really badly timed mixer access right between entering
FPGA programming mode and uploading the netlist would mess up the
protocol.
ALSA: emu10k1: move the whole GPIO event handling to the workqueue
The actual event processing was already done by workqueue items. We can
move the event dispatching there as well, rather than doing it already
in the interrupt handler callback.
This change has a rather profound "side effect" on the reliability of
the FPGA programming: once we enter programming mode, we must not issue
any snd_emu1010_fpga_{read,write}() calls until we're done, as these
would badly mess up the programming protocol. But exactly that would
happen when trying to program the dock, as that triggers GPIO interrupts
as a side effect. This is mitigated by deferring the actual interrupt
handling, as workqueue items are not re-entrant.
To avoid scheduling the dispatcher on non-events, we now explicitly
ignore GPIO IRQs triggered by "uninteresting" pins, which happens a lot
as a side effect of calling snd_emu1010_fpga_{read,write}().
ALSA: emu10k1: factor out snd_emu1010_load_dock_firmware()
Pulled out of the next patch to improve its legibility.
As the function is now available, call it directly from
snd_emu10k1_emu1010_init(), thus making the MicroDock firmware loading
synchronous - there isn't really a reason not to. Note that this does
not affect the AudioDocks of rev1 cards, as these have no independent
power supplies, and thus come up only a while after the main card is
initialized.
As a drive-by, adjust the priorities of two messages to better reflect
their impact.
ALSA: emu10k1: fix E-MU card dock presence monitoring
While there are two separate IRQ status bits for dock attach and detach,
the hardware appears to mix them up more or less randomly, making them
useless for tracking what actually happened. It is much safer to check
the dock status separately and proceed based on that, as the old polling
code did.
Note that the code assumes that only the dock can be hot-plugged - if
other option card bits changed, the logic would break.
sched/isolation: Fix boot crash when maxcpus < first housekeeping CPU
housekeeping_setup() checks cpumask_intersects(present, online) to ensure
that the kernel will have at least one housekeeping CPU after smp_init(),
but this doesn't work if the maxcpus= kernel parameter limits the number of
processors available after bootup.
For example, a kernel with "maxcpus=2 nohz_full=0-2" parameters crashes at
boot time on a virtual machine with 4 CPUs.
Change housekeeping_setup() to use cpumask_first_and() and check that the
returned CPU number is valid and less than setup_max_cpus.
Another corner case is "nohz_full=0" on a machine with a single CPU or with
the maxcpus=1 kernel argument. In this case non_housekeeping_mask is empty
and tick_nohz_full_setup() makes no sense. And indeed, the kernel hits the
WARN_ON(tick_nohz_full_running) in tick_sched_do_timer().
And how should the kernel interpret the "nohz_full=" parameter? It should
be silently ignored, but currently cpulist_parse() happily returns the
empty cpumask and this leads to the same problem.
Change housekeeping_setup() to check cpumask_empty(non_housekeeping_mask)
and do nothing in this case.
sched/isolation: Prevent boot crash when the boot CPU is nohz_full
Documentation/timers/no_hz.rst states that the "nohz_full=" mask must not
include the boot CPU, which is no longer true after:
08ae95f4fd3b ("nohz_full: Allow the boot CPU to be nohz_full").
However after:
aae17ebb53cd ("workqueue: Avoid using isolated cpus' timers on queue_delayed_work")
the kernel will crash at boot time in this case; housekeeping_any_cpu()
returns an invalid CPU number until smp_init() brings the first
housekeeping CPU up.
Change housekeeping_any_cpu() to check the result of cpumask_any_and() and
return smp_processor_id() in this case.
This is just the simple and backportable workaround which fixes the
symptom, but smp_processor_id() at boot time should be safe at least for
type == HK_TYPE_TIMER, this more or less matches the tick_do_timer_boot_cpu
logic.
There is no worry about cpu_down(); tick_nohz_cpu_down() will not allow to
offline tick_do_timer_cpu (the 1st online housekeeping CPU).
Merge tag 'rust-fixes-6.9' of https://github.com/Rust-for-Linux/linux
Pull Rust fixes from Miguel Ojeda:
- Soundness: make internal functions generated by the 'module!' macro
inaccessible, do not implement 'Zeroable' for 'Infallible' and
require 'Send' for the 'Module' trait.
- Build: avoid errors with "empty" files and workaround 'rustdoc' ICE.
- Kconfig: depend on '!CFI_CLANG' and avoid selecting 'CONSTRUCTORS'.
- Code docs: remove non-existing key from 'module!' macro example.
- Docs: trivial rendering fix in arch table.
* tag 'rust-fixes-6.9' of https://github.com/Rust-for-Linux/linux:
rust: remove `params` from `module` macro example
kbuild: rust: force `alloc` extern to allow "empty" Rust files
kbuild: rust: remove unneeded `@rustc_cfg` to avoid ICE
rust: kernel: require `Send` for `Module` implementations
rust: phy: implement `Send` for `Registration`
rust: make mutually exclusive with CFI_CLANG
rust: macros: fix soundness issue in `module!` macro
rust: init: remove impl Zeroable for Infallible
docs: rust: fix improper rendering in Arch Support page
rust: don't select CONSTRUCTORS
Merge tag 'riscv-for-linus-6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix for TASK_SIZE on rv64/NOMMU, to reflect the lack of user/kernel
separation
- A fix to avoid loading rv64/NOMMU kernel past the start of RAM
- A fix for RISCV_HWPROBE_EXT_ZVFHMIN on ilp32 to avoid signed integer
overflow in the bitmask
- The sud_test kselftest has been fixed to properly swizzle the syscall
number into the return register, which are not the same on RISC-V
- A fix for a build warning in the perf tools on rv32
- A fix for the CBO selftests, to avoid non-constants leaking into the
inline asm
- A pair of fixes for T-Head PBMT errata probing, which has been
renamed MAE by the vendor
* tag 'riscv-for-linus-6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: selftests: cbo: Ensure asm operands match constraints, take 2
perf riscv: Fix the warning due to the incompatible type
riscv: T-Head: Test availability bit before enabling MAE errata
riscv: thead: Rename T-Head PBMT to MAE
selftests: sud_test: return correct emulated syscall value on RISC-V
riscv: hwprobe: fix invalid sign extension for RISCV_HWPROBE_EXT_ZVFHMIN
riscv: Fix loading 64-bit NOMMU kernels past the start of RAM
riscv: Fix TASK_SIZE on 64-bit NOMMU
Merge tag 'i2c-for-6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Fix a race condition in the at24 eeprom handler, a NULL pointer
exception in the I2C core for controllers only using target modes,
drop a MAINTAINERS entry, and fix an incorrect DT binding for at24"
* tag 'i2c-for-6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: smbus: fix NULL function pointer dereference
MAINTAINERS: Drop entry for PCA9541 bus master selector
eeprom: at24: fix memory corruption race condition
dt-bindings: eeprom: at24: Fix ST M24C64-D compatible schema
Merge tag 'soundwire-6.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire fix from Vinod Koul:
- Single AMD driver fix for wake interrupt handling in clockstop mode
* tag 'soundwire-6.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: amd: fix for wake interrupt handling for clockstop mode
Wolfram Sang [Fri, 26 Apr 2024 06:44:08 +0000 (08:44 +0200)]
i2c: smbus: fix NULL function pointer dereference
Baruch reported an OOPS when using the designware controller as target
only. Target-only modes break the assumption of one transfer function
always being available. Fix this by always checking the pointer in
__i2c_transfer.
Reported-by: Baruch Siach <[email protected]> Closes: https://lore.kernel.org/r/4269631780e5ba789cf1ae391eec1b959def7d99.1712761976.git.baruch@tkos.co.il Fixes: 4b1acc43331d ("i2c: core changes for slave support")
[wsa: dropped the simplification in core-smbus to avoid theoretical regressions] Signed-off-by: Wolfram Sang <[email protected]> Tested-by: Baruch Siach <[email protected]>
Merge tag 'soc-fixes-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are a lot of minor DT fixes for Mediatek, Rockchip, Qualcomm and
Microchip and NXP, addressing both build-time warnings and bugs found
during runtime testing.
Most of these changes are machine specific fixups, but there are a few
notable regressions that affect an entire SoC:
- The Qualcomm MSI support that was improved for 6.9 ended up being
wrong on some chips and now gets fixed.
- The i.MX8MP camera interface broke due to a typo and gets updated
again.
The main driver fix is also for Qualcomm platforms, rewriting an
interface in the QSEECOM firmware support that could lead to crashing
the kernel from a trusted application.
The only other code changes are minor fixes for Mediatek SoC drivers"
* tag 'soc-fixes-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (50 commits)
ARM: dts: imx6ull-tarragon: fix USB over-current polarity
soc: mediatek: mtk-socinfo: depends on CONFIG_SOC_BUS
soc: mediatek: mtk-svs: Append "-thermal" to thermal zone names
arm64: dts: imx8mp: Fix assigned-clocks for second CSI2
ARM: dts: microchip: at91-sama7g54_curiosity: Replace regulator-suspend-voltage with the valid property
ARM: dts: microchip: at91-sama7g5ek: Replace regulator-suspend-voltage with the valid property
arm64: dts: rockchip: Fix USB interface compatible string on kobol-helios64
arm64: dts: qcom: sc8180x: Fix ss_phy_irq for secondary USB controller
arm64: dts: qcom: sm8650: Fix the msi-map entries
arm64: dts: qcom: sm8550: Fix the msi-map entries
arm64: dts: qcom: sm8450: Fix the msi-map entries
arm64: dts: qcom: sc8280xp: add missing PCIe minimum OPP
arm64: dts: qcom: x1e80100: Fix the compatible for cluster idle states
arm64: dts: qcom: Fix type of "wdog" IRQs for remoteprocs
arm64: dts: rockchip: regulator for sd needs to be always on for BPI-R2Pro
dt-bindings: rockchip: grf: Add missing type to 'pcie-phy' node
arm64: dts: rockchip: drop redundant disable-gpios in Lubancat 2
arm64: dts: rockchip: drop redundant disable-gpios in Lubancat 1
arm64: dts: rockchip: drop redundant pcie-reset-suspend in Scarlet Dumo
arm64: dts: rockchip: mark system power controller and fix typo on orangepi-5-plus
...
Merge tag 'mm-hotfixes-stable-2024-04-26-13-30' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"11 hotfixes. 8 are cc:stable and the remaining 3 (nice ratio!) address
post-6.8 issues or aren't considered suitable for backporting.
All except one of these are for MM. I see no particular theme - it's
singletons all over"
* tag 'mm-hotfixes-stable-2024-04-26-13-30' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/hugetlb: fix DEBUG_LOCKS_WARN_ON(1) when dissolve_free_hugetlb_folio()
selftests: mm: protection_keys: save/restore nr_hugepages value from launch script
stackdepot: respect __GFP_NOLOCKDEP allocation flag
hugetlb: check for anon_vma prior to folio allocation
mm: zswap: fix shrinker NULL crash with cgroup_disable=memory
mm: turn folio_test_hugetlb into a PageType
mm: support page_mapcount() on page_has_type() pages
mm: create FOLIO_FLAG_FALSE and FOLIO_TYPE_OPS macros
mm/hugetlb: fix missing hugetlb_lock for resv uncharge
selftests: mm: fix unused and uninitialized variable warning
selftests/harness: remove use of LINE_MAX
Merge tag 'mtd/fixes-for-6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"There has been OTP support improvements in the NVMEM subsystem, and
later also improvements of OTP support in the NAND subsystem. This
lead to situations that we currently cannot handle, so better prevent
this situation from happening in order to avoid canceling device's
probe.
In the raw NAND subsystem, two runtime fixes have been shared, one
fixing two important commands in the Qcom driver since it got reworked
and a NULL pointer dereference happening on STB chips.
Arnd also fixed a UBSAN link failure on diskonchip"
* tag 'mtd/fixes-for-6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: limit OTP NVMEM cell parse to non-NAND devices
mtd: diskonchip: work around ubsan link failure
mtd: rawnand: qcom: Fix broken OP_RESET_DEVICE command in qcom_misc_cmd_type_exec()
mtd: rawnand: brcmnand: Fix data access violation for STB chip
projects / linux.git / log