Kai-Heng Feng [Wed, 15 Mar 2023 12:07:23 +0000 (20:07 +0800)]
drm/amdgpu/nv: Apply ASPM quirk on Intel ADL + AMD Navi
S2idle resume freeze can be observed on Intel ADL + AMD WX5500. This is
caused by commit 0064b0ce85bb ("drm/amd/pm: enable ASPM by default").
The root cause is still not clear for now.
So extend and apply the ASPM quirk from commit e02fe3bc7aba
("drm/amdgpu: vi: disable ASPM on Intel Alder Lake based systems"), to
workaround the issue on Navi cards too.
YuBiao Wang [Thu, 16 Mar 2023 03:30:32 +0000 (11:30 +0800)]
drm/amdgpu: Force signal hw_fences that are embedded in non-sched jobs
[Why]
For engines not supporting soft reset, i.e. VCN, there will be a failed
ib test before mode 1 reset during asic reset. The fences in this case
are never signaled and next time when we try to free the sa_bo, kernel
will hang.
[How]
During pre_asic_reset, driver will clear job fences and afterwards the
fences' refcount will be reduced to 1. For drm_sched_jobs it will be
released in job_free_cb, and for non-sched jobs like ib_test, it's meant
to be released in sa_bo_free but only when the fences are signaled. So
we have to force signal the non_sched bad job's fence during
pre_asic_reset or the clear is not complete.
Tong Liu01 [Wed, 15 Mar 2023 07:24:22 +0000 (15:24 +0800)]
drm/amdgpu: add mes resume when do gfx post soft reset
[why]
when gfx do soft reset, mes will also do reset, if mes is not
resumed when do recover from soft reset, mes is unable to respond
in later sequence
Tim Huang [Thu, 9 Mar 2023 08:27:51 +0000 (16:27 +0800)]
drm/amdgpu: skip ASIC reset for APUs when go to S4
For GC IP v11.0.4/11, PSP TMR need to be reserved
for ASIC mode2 reset. But for S4, when psp suspend,
it will destroy the TMR that fails the ASIC reset.
Ard Biesheuvel [Wed, 22 Mar 2023 00:11:18 +0000 (01:11 +0100)]
efi/libstub: Use relocated version of kernel's struct screen_info
In some cases, we expose the kernel's struct screen_info to the EFI stub
directly, so it gets populated before even entering the kernel. This
means the early console is available as soon as the early param parsing
happens, which is nice. It also means we need two different ways to pass
this information, as this trick only works if the EFI stub is baked into
the core kernel image, which is not always the case.
Huacai reports that the preparatory refactoring that was needed to
implement this alternative method for zboot resulted in a non-functional
efifb earlycon for other cases as well, due to the reordering of the
kernel image relocation with the population of the screen_info struct,
and the latter now takes place after copying the image to its new
location, which means we copy the old, uninitialized state.
So let's ensure that the same-image version of alloc_screen_info()
produces the correct screen_info pointer, by taking the displacement of
the loaded image into account.
In device_for_each_child_node(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.") Signed-off-by: Liang He <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jakub Kicinski [Thu, 23 Mar 2023 05:50:01 +0000 (22:50 -0700)]
Merge tag 'mlx5-fixes-2023-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2023-03-21
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: E-Switch, Fix an Oops in error handling code
net/mlx5: Read the TC mapping of all priorities on ETS query
net/mlx5e: Overcome slow response for first macsec ASO WQE
net/mlx5e: Initialize link speed to zero
net/mlx5: Fix steering rules cleanup
net/mlx5e: Block entering switchdev mode with ns inconsistency
net/mlx5e: Set uplink rep as NETNS_LOCAL
====================
Jakub Kicinski [Thu, 23 Mar 2023 05:45:22 +0000 (22:45 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-21 (ice)
This series contains updates to ice driver only.
Piotr sets first_desc field for proper handling of Flow Director
packets.
Michal moves error checking for VF earlier in function to properly return
error before other checks/reporting; he also corrects VSI filter removal to
be done during VSI removal and not rebuild.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: remove filters only if VSI is deleted
ice: check if VF exists before mode check
ice: fix rx buffers handling for flow director packets
====================
Jakub Kicinski [Thu, 23 Mar 2023 05:42:15 +0000 (22:42 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-21 (iavf, i40e)
This series contains updates to iavf and i40e drivers.
Stefan Assmann adds check, and return, if driver has already gone
through remove to prevent hang for iavf.
Radoslaw adds zero initialization to ensure Flow Director packets are
populated with correct values for i40e.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: fix flow director packet filter programming
iavf: fix hang on reboot with ice
====================
Arınç ÜNAL [Mon, 20 Mar 2023 19:05:19 +0000 (22:05 +0300)]
net: dsa: mt7530: move lowering TRGMII driving to mt7530_setup()
Move lowering the TRGMII Tx clock driving to mt7530_setup(), after setting
the core clock, as seen on the U-Boot MediaTek ethernet driver.
Move the code which looks like it lowers the TRGMII Rx clock driving to
after the TRGMII Tx clock driving is lowered. This is run after lowering
the Tx clock driving on the U-Boot MediaTek ethernet driver as well.
This way, the switch should consume less power regardless of port 6 being
used.
Update the comment explaining mt7530_pad_clk_setup().
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Arınç ÜNAL [Mon, 20 Mar 2023 19:05:18 +0000 (22:05 +0300)]
net: dsa: mt7530: move enabling disabling core clock to mt7530_pll_setup()
Split the code that enables and disables TRGMII clocks and core clock.
Move enabling and disabling core clock to mt7530_pll_setup() as it's
supposed to be run there.
Add 20 ms delay before enabling the core clock as seen on the U-Boot
MediaTek ethernet driver.
Change the comment for enabling and disabling TRGMII clocks as the code
seems to affect both TXC and RXC.
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Issue was originally reported by Anton Lundin on 2022-06-22 (link below).
Chrome OS team hit the same issue in Feb, 2023 when trying to find
work arounds for other issues with AX88172 devices.
The use of devm_mdiobus_register() with usbnet devices results in the
MDIO data being associated with the USB device. When the asix driver
is unloaded, the USB device continues to exist and the corresponding
"mdiobus_unregister()" is NOT called until the USB device is unplugged
or unauthorized. So the next "modprobe asix" will fail because the MDIO
phy sysfs attributes still exist.
The 'easy' (from a design PoV) fix is to use the non-devm variants of
mdiobus_* functions and explicitly manage this use in the asix_bind
and asix_unbind function calls. I've not explored trying to fix usbnet
initialization so devm_* stuff will work.
The link speed is never changed for the uptime of a VM, and the current
implementation sends an admin queue command for each call. Admin queue
command invocations have nontrivial overhead (e.g., VM exits), which can
be disruptive to users if triggered frequently. Our telemetry data shows
that there are VMs that make frequent calls to this admin queue command.
Caching the result of the original admin queue command would eliminate
the need to send multiple admin queue commands on subsequent calls to
retrieve link speed.
Shyam Prasad N [Mon, 20 Feb 2023 13:02:11 +0000 (13:02 +0000)]
cifs: lock chan_lock outside match_session
Coverity had rightly indicated a possible deadlock
due to chan_lock being done inside match_session.
All callers of match_* functions should pick up the
necessary locks and call them.
Vladimir Oltean [Tue, 21 Mar 2023 23:28:31 +0000 (01:28 +0200)]
net: enetc: fix aggregate RMON counters not showing the ranges
When running "ethtool -S eno0 --groups rmon" without an explicit "--src
emac|pmac" argument, the kernel will not report
rx-rmon-etherStatsPkts64to64Octets, rx-rmon-etherStatsPkts65to127Octets,
etc. This is because on ETHTOOL_MAC_STATS_SRC_AGGREGATE, we do not
populate the "ranges" argument.
ocelot_port_get_rmon_stats() does things differently and things work
there. I had forgotten to make sure that the code is structured the same
way in both drivers, so do that now.
Brian Gix [Mon, 6 Mar 2023 22:32:21 +0000 (14:32 -0800)]
Bluetooth: Remove "Power-on" check from Mesh feature
The Bluetooth mesh experimental feature enable was requiring the
controller to be powered off in order for the Enable to work. Mesh is
supposed to be enablable regardless of the controller state, and created
an unintended requirement that the mesh daemon be started before the
classic bluetoothd daemon.
Fixes: af6bcc1921ff ("Bluetooth: Add experimental wrapper for MGMT based mesh") Signed-off-by: Brian Gix <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Min Li [Sat, 4 Mar 2023 13:50:35 +0000 (21:50 +0800)]
Bluetooth: Fix race condition in hci_cmd_sync_clear
There is a potential race condition in hci_cmd_sync_work and
hci_cmd_sync_clear, and could lead to use-after-free. For instance,
hci_cmd_sync_work is added to the 'req_workqueue' after cancel_work_sync
The entry of 'cmd_sync_work_list' may be freed in hci_cmd_sync_clear, and
causing kernel panic when it is used in 'hci_cmd_sync_work'.
Fixes: 6a98e3836fa2 ("Bluetooth: Add helper for serialized HCI command execution") Cc: [email protected] Signed-off-by: Min Li <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Kiran K [Tue, 28 Feb 2023 11:01:54 +0000 (16:31 +0530)]
Bluetooth: btintel: Iterate only bluetooth device ACPI entries
Current flow interates over entire ACPI table entries looking for
Bluetooth Per Platform Antenna Gain(PPAG) entry. This patch iterates
over ACPI entries relvant to Bluetooth device only.
Fixes: c585a92b2f9c ("Bluetooth: btintel: Set Per Platform Antenna Gain(PPAG)") Signed-off-by: Kiran K <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Pauli Virtanen [Mon, 20 Feb 2023 19:38:24 +0000 (19:38 +0000)]
Bluetooth: ISO: fix timestamped HCI ISO data packet parsing
Use correct HCI ISO data packet header struct when the packet has
timestamp. The timestamp, when present, goes before the other fields
(Core v5.3 4E 5.4.5), so the structs are not compatible.
Fixes: ccf74f2390d6 ("Bluetooth: Add BTPROTO_ISO socket type") Signed-off-by: Pauli Virtanen <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Bluetooth: hci_core: Detect if an ACL packet is in fact an ISO packet
Because some transports don't have a dedicated type for ISO packets
(see 14202eff214e1e941fefa0366d4c3bc4b1a0d500) they may use ACL type
when in fact they are ISO packets.
In the past this was left for the driver to detect such thing but it
creates a problem when using the likes of btproxy when used by a VM as
the host would not be aware of the connection the guest is doing it
won't be able to detect such behavior, so this make bt_recv_frame
detect when it happens as it is the common interface to all drivers
including guest VMs.
Fixes: 14202eff214e ("Bluetooth: btusb: Detect if an ACL packet is in fact an ISO packet") Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Zhengping Jiang [Wed, 22 Feb 2023 00:17:56 +0000 (16:17 -0800)]
Bluetooth: hci_sync: Resume adv with no RPA when active scan
The address resolution should be disabled during the active scan,
so all the advertisements can reach the host. The advertising
has to be paused before disabling the address resolution,
because the advertising will prevent any changes to the resolving
list and the address resolution status. Skipping this will cause
the hci error and the discovery failure.
According to the bluetooth specification:
"7.8.44 LE Set Address Resolution Enable command
This command shall not be used when:
- Advertising (other than periodic advertising) is enabled,
- Scanning is enabled, or
- an HCI_LE_Create_Connection, HCI_LE_Extended_Create_Connection, or
HCI_LE_Periodic_Advertising_Create_Sync command is outstanding."
If the host is using RPA, the controller needs to generate RPA for
the advertising, so the advertising must remain paused during the
active scan.
If the host is not using RPA, the advertising can be resumed after
disabling the address resolution.
Fixes: 9afc675edeeb ("Bluetooth: hci_sync: allow advertise when scan without RPA") Signed-off-by: Zhengping Jiang <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Namjae Jeon [Tue, 21 Mar 2023 06:25:34 +0000 (15:25 +0900)]
ksmbd: don't terminate inactive sessions after a few seconds
Steve reported that inactive sessions are terminated after a few
seconds. ksmbd terminate when receiving -EAGAIN error from
kernel_recvmsg(). -EAGAIN means there is no data available in timeout.
So ksmbd should keep connection with unlimited retries instead of
terminating inactive sessions.
Namjae Jeon [Tue, 7 Mar 2023 12:56:07 +0000 (21:56 +0900)]
ksmbd: add low bound validation to FSCTL_QUERY_ALLOCATED_RANGES
Smatch static checker warning:
fs/ksmbd/vfs.c:1040 ksmbd_vfs_fqar_lseek() warn: no lower bound on 'length'
fs/ksmbd/vfs.c:1041 ksmbd_vfs_fqar_lseek() warn: no lower bound on 'start'
Fix unexpected result that could caused from negative start and length.
Namjae Jeon [Tue, 28 Feb 2023 15:02:30 +0000 (00:02 +0900)]
ksmbd: set FILE_NAMED_STREAMS attribute in FS_ATTRIBUTE_INFORMATION
If vfs objects = streams_xattr in ksmbd.conf FILE_NAMED_STREAMS should
be set to Attributes in FS_ATTRIBUTE_INFORMATION. MacOS client show
"Format: SMB (Unknown)" on faked NTFS and no streams support.
Namjae Jeon [Tue, 28 Feb 2023 15:01:21 +0000 (00:01 +0900)]
ksmbd: fix wrong signingkey creation when encryption is AES256
MacOS and Win11 support AES256 encrytion and it is included in the cipher
array of encryption context. Especially on macOS, The most preferred
cipher is AES256. Connecting to ksmbd fails on newer MacOS clients that
support AES256 encryption. MacOS send disconnect request after receiving
final session setup response from ksmbd. Because final session setup is
signed with signing key was generated incorrectly.
For signging key, 'L' value should be initialized to 128 if key size is
16bytes.
Linus Torvalds [Wed, 22 Mar 2023 21:09:20 +0000 (14:09 -0700)]
Merge tag 'bootconfig-fixes-v6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull bootconfig fixes from Masami Hiramatsu:
- Fix bootconfig test script to test increased maximum number (8192)
node correctly
- Change the console message if there is no bootconfig data and the
kernel is compiled with CONFIG_BOOT_CONFIG_FORCE=y
* tag 'bootconfig-fixes-v6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
bootconfig: Change message if no bootconfig with CONFIG_BOOT_CONFIG_FORCE=y
bootconfig: Fix testcase to increase max node
Chuck Lever [Wed, 22 Mar 2023 19:01:34 +0000 (15:01 -0400)]
SUNRPC: Fix a crash in gss_krb5_checksum()
Anna says:
> KASAN reports [...] a slab-out-of-bounds in gss_krb5_checksum(),
> and it can cause my client to panic when running cthon basic
> tests with krb5p.
> Running faddr2line gives me:
>
> gss_krb5_checksum+0x4b6/0x630:
> ahash_request_free at
> /home/anna/Programs/linux-nfs.git/./include/crypto/hash.h:619
> (inlined by) gss_krb5_checksum at
> /home/anna/Programs/linux-nfs.git/net/sunrpc/auth_gss/gss_krb5_crypto.c:358
My diagnosis is that the memcpy() at the end of gss_krb5_checksum()
reads past the end of the buffer containing the checksum data
because the callers have ignored gss_krb5_checksum()'s API contract:
* Caller provides the truncation length of the output token (h) in
* cksumout.len.
Instead they provide the fixed length of the hmac buffer. This
length happens to be larger than the value returned by
crypto_ahash_digestsize().
Change these errant callers to work like krb5_etm_{en,de}crypt().
As a defensive measure, bound the length of the byte copy at the
end of gss_krb5_checksum().
Merge tag 'thunderbolt-for-v6.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fixes for v6.3-rc4
This includes following fixes and quirks for v6.3-rc:
- Quirk to disable CL-states on AMD USB4 host routers
- Fix memory leak in lane margining
- Correct the retimer access flows
- Quirk to limit USB3 bandwidth on certain Intel USB4 host routers
- Fix usage of scale field when allocting USB3 bandwidth
- Fix interrupt "auto clear" on non-Intel USB4 host routers.
There are also two commits that are not fixes themselves but are needed
for the USB3 bandwidth quirk and for the interrupt auto clear fix to
work.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Rename shadowed variables bit to interrupt_bit and auto_clear_bit
thunderbolt: Disable interrupt auto clear for rings
thunderbolt: Use const qualifier for `ring_interrupt_index`
thunderbolt: Use scale field when allocating USB3 bandwidth
thunderbolt: Limit USB3 bandwidth of certain Intel USB4 host routers
thunderbolt: Call tb_check_quirks() after initializing adapters
thunderbolt: Add missing UNSET_INBOUND_SBTX for retimer access
thunderbolt: Fix memory leak in margining
thunderbolt: Add quirk to disable CLx
Commit 7c3d5c20dc16 ("thermal/core: Add a generic thermal_zone_get_trip()
function") stopped marking trip points with a zero temperature as
disabled, behavior that was originally introduced in commit 81ad4276b505
("Thermal: Ignore invalid trip points").
When using the mlxsw driver we see that when such trip points are not
disabled, the thermal subsystem repeatedly tries to set the state of the
associated cooling devices to the maximum state.
Address this by restoring the original behavior and mark trip points
with a zero temperature as disabled.
Fixes: 7c3d5c20dc16 ("thermal/core: Add a generic thermal_zone_get_trip() function") Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
Chang S. Bae [Mon, 27 Feb 2023 21:05:03 +0000 (13:05 -0800)]
x86/fpu/xstate: Prevent false-positive warning in __copy_xstate_uabi_buf()
__copy_xstate_to_uabi_buf() copies either from the tasks XSAVE buffer
or from init_fpstate into the ptrace buffer. Dynamic features, like
XTILEDATA, have an all zeroes init state and are not saved in
init_fpstate, which means the corresponding bit is not set in the
xfeatures bitmap of the init_fpstate header.
But __copy_xstate_to_uabi_buf() retrieves addresses for both the tasks
xstate and init_fpstate unconditionally via __raw_xsave_addr().
So if the tasks XSAVE buffer has a dynamic feature set, then the
address retrieval for init_fpstate triggers the warning in
__raw_xsave_addr() which checks the feature bit in the init_fpstate
header.
Remove the address retrieval from init_fpstate for extended features.
They have an all zeroes init state so init_fpstate has zeros for them.
Then zeroing the user buffer for the init state is the same as copying
them from init_fpstate.
Michal Koutný [Mon, 6 Mar 2023 19:31:44 +0000 (20:31 +0100)]
x86/mm: Do not shuffle CPU entry areas without KASLR
The commit 97e3d26b5e5f ("x86/mm: Randomize per-cpu entry area") fixed
an omission of KASLR on CPU entry areas. It doesn't take into account
KASLR switches though, which may result in unintended non-determinism
when a user wants to avoid it (e.g. debugging, benchmarking).
Generate only a single combination of CPU entry areas offsets -- the
linear array that existed prior randomization when KASLR is turned off.
Since we have 3f148f331814 ("x86/kasan: Map shadow for percpu pages on
demand") and followups, we can use the more relaxed guard
kasrl_enabled() (in contrast to kaslr_memory_enabled()).
Savino Dicanosa [Tue, 21 Mar 2023 19:44:02 +0000 (19:44 +0000)]
io_uring/rsrc: fix null-ptr-deref in io_file_bitmap_get()
When fixed files are unregistered, file_alloc_end and alloc_hint
are not cleared. This can later cause a NULL pointer dereference in
io_file_bitmap_get() if auto index selection is enabled via
IORING_FILE_INDEX_ALLOC:
Matheus Castello [Wed, 22 Mar 2023 14:38:21 +0000 (15:38 +0100)]
drm/bridge: lt8912b: return EPROBE_DEFER if bridge is not found
Returns EPROBE_DEFER when of_drm_find_bridge() fails, this is consistent
with what all the other DRM bridge drivers are doing and this is
required since the bridge might not be there when the driver is probed
and this should not be a fatal failure.
xdp: bpf_xdp_metadata use EOPNOTSUPP for no driver support
When driver doesn't implement a bpf_xdp_metadata kfunc the fallback
implementation returns EOPNOTSUPP, which indicate device driver doesn't
implement this kfunc.
Currently many drivers also return EOPNOTSUPP when the hint isn't
available, which is ambiguous from an API point of view. Instead
change drivers to return ENODATA in these cases.
There can be natural cases why a driver doesn't provide any hardware
info for a specific hint, even on a frame to frame basis (e.g. PTP).
Lets keep these cases as separate return codes.
When describing the return values, adjust the function kernel-doc layout
to get proper rendering for the return values.
Jan Beulich [Tue, 21 Mar 2023 08:03:26 +0000 (09:03 +0100)]
x86/PVH: avoid 32-bit build warning when obtaining VGA console info
In the commit referenced below I failed to pay attention to this code
also being buildable as 32-bit. Adjust the type of "ret" - there's no
real need for it to be wider than 32 bits.
Roger Pau Monne [Wed, 30 Nov 2022 15:09:11 +0000 (16:09 +0100)]
hvc/xen: prevent concurrent accesses to the shared ring
The hvc machinery registers both a console and a tty device based on
the hv ops provided by the specific implementation. Those two
interfaces however have different locks, and there's no single locks
that's shared between the tty and the console implementations, hence
the driver needs to protect itself against concurrent accesses.
Otherwise concurrent calls using the split interfaces are likely to
corrupt the ring indexes, leaving the console unusable.
Introduce a lock to xencons_info to serialize accesses to the shared
ring. This is only required when using the shared memory console,
concurrent accesses to the hypercall based console implementation are
not an issue.
Note the conditional logic in domU_read_console() is slightly modified
so the notify_daemon() call can be done outside of the locked region:
it's an hypercall and there's no need for it to be done with the lock
held.
Ido Schimmel [Tue, 21 Mar 2023 11:42:00 +0000 (12:42 +0100)]
mlxsw: spectrum_fid: Fix incorrect local port type
Local port is a 10-bit number, but it was mistakenly stored in a u8,
resulting in firmware errors when using a netdev corresponding to a
local port higher than 255.
Fix by storing the local port in u16, as is done in the rest of the
code.
ACPI: processor: thermal: Update CPU cooling devices on cpufreq policy changes
When a cpufreq policy appears or goes away, the CPU cooling devices for
the CPUs covered by that policy need to be updated so that the new
processor_get_max_state() value is stored as max_state and the
statistics in sysfs are rearranged for each of them.
Do that accordingly in acpi_thermal_cpufreq_init() and
acpi_thermal_cpufreq_exit().
Introduce a core thermal API function, thermal_cooling_device_update(),
for updating the max_state value for a cooling device and rearranging
its statistics in sysfs after a possible change of its ->get_max_state()
callback return value.
That callback is now invoked only once, during cooling device
registration, to populate the max_state field in the cooling device
object, so if its return value changes, it needs to be invoked again
and the new return value needs to be stored as max_state. Moreover,
the statistics presented in sysfs need to be rearranged in general,
because there may not be enough room in them to store data for all
of the possible states (in the case when max_state grows).
The new function takes care of that (and some other minor things
related to it), but some extra locking and lockdep annotations are
added in several places too to protect against crashes in the cases
when the statistics are not present or when a stale max_state value
might be used by sysfs attributes.
Note that the actual user of the new function will be added separately.
Introduce a helper function, thermal_cooling_device_present(), for
checking if the given cooling device is in the list of registered
cooling devices to avoid some code duplication in a subsequent
patch.
The cpufreq policy notifier in the ACPI processor driver may as
well be registered before the driver itself, which causes
acpi_processor_cpufreq_init to be true (unless the notifier
registration fails, which is unlikely at that point) when the
ACPI CPU thermal cooling devices are registered, so the
processor_get_max_state() result does not change while
acpi_processor_driver_init() is running.
Change the ordering in acpi_processor_driver_init() accordingly
to prevent the max_state value from remaining 0 permanently for all
ACPI CPU cooling devices due to setting acpi_processor_cpufreq_init
too late. [Note that processor_get_max_state() may still return
different values at different times after this change, depending on
the cpufreq driver registration time, but that issue needs to be
addressed separately.]
bootconfig: Change message if no bootconfig with CONFIG_BOOT_CONFIG_FORCE=y
Change no bootconfig data error message if user do not specify 'bootconfig'
option but CONFIG_BOOT_CONFIG_FORCE=y.
With CONFIG_BOOT_CONFIG_FORCE=y, the kernel proceeds bootconfig check even
if user does not specify 'bootconfig' option. So the current error message
is confusing. Let's show just an information message to notice skipping
the bootconfig in that case.
Felix Fietkau [Tue, 14 Mar 2023 09:59:52 +0000 (10:59 +0100)]
wifi: mac80211: fix mesh path discovery based on unicast packets
If a packet has reached its intended destination, it was bumped to the code
that accepts it, without first checking if a mesh_path needs to be created
based on the discovered source.
Fix this by moving the destination address check further down.
Felix Fietkau [Tue, 14 Mar 2023 09:59:50 +0000 (10:59 +0100)]
wifi: mac80211: fix qos on mesh interfaces
When ieee80211_select_queue is called for mesh, the sta pointer is usually
NULL, since the nexthop is looked up much later in the tx path.
Explicitly check for unicast address in that case in order to make qos work
again.
Johannes Berg [Fri, 17 Mar 2023 09:53:25 +0000 (10:53 +0100)]
wifi: iwlwifi: mvm: protect TXQ list manipulation
Some recent upstream debugging uncovered the fact that in
iwlwifi, the TXQ list manipulation is racy.
Introduce a new state bit for when the TXQ is completely
ready and can be used without locking, and if that's not
set yet acquire the lock to check everything correctly.
Johannes Berg [Fri, 17 Mar 2023 09:53:24 +0000 (10:53 +0100)]
wifi: iwlwifi: mvm: fix mvmtxq->stopped handling
This could race if the queue is redirected while full, then
the flushing internally would start it while it's not yet
usable again. Fix it by using two state bits instead of just
one.
mm/slab: Fix undefined init_cache_node_node() for NUMA and !SMP
sh/migor_defconfig:
mm/slab.c: In function ‘slab_memory_callback’:
mm/slab.c:1127:23: error: implicit declaration of function ‘init_cache_node_node’; did you mean ‘drain_cache_node_node’? [-Werror=implicit-function-declaration]
1127 | ret = init_cache_node_node(nid);
| ^~~~~~~~~~~~~~~~~~~~
| drain_cache_node_node
The #ifdef condition protecting the definition of init_cache_node_node()
no longer matches the conditions protecting the (multiple) users.
Caleb Sander [Mon, 20 Mar 2023 15:57:36 +0000 (09:57 -0600)]
nvme-tcp: fix nvme_tcp_term_pdu to match spec
The FEI field of C2HTermReq/H2CTermReq is 4 bytes but not 4-byte-aligned
in the NVMe/TCP specification (it is located at offset 10 in the PDU).
Split it into two 16-bit integers in struct nvme_tcp_term_pdu
so no padding is inserted. There should also be 10 reserved bytes after.
There are currently no users of this type.
====================
Fix trainwreck with Ocelot switch statistics counters
While testing the patch set for preemptible traffic classes with some
controlled traffic and measuring counter deltas:
https://lore.kernel.org/netdev/20230220122343.1156614[email protected]/
I noticed that in the output of "ethtool -S swp0 --groups eth-mac
eth-phy eth-ctrl rmon -- --src emac | grep -v ': 0'", the TX counters
were off. Quickly I realized that their values were permutated by 1
compared to their names, and that for example
tx-rmon-etherStatsPkts64to64Octets was incrementing when
tx-rmon-etherStatsPkts65to127Octets should have.
Initially I suspected something having to do with the bulk reading
logic, and indeed I found a bug there (fixed as 1/3), but that was not
the source of the problems. Instead it revealed other problems.
While dumping the regions created by the driver on my switch, I figured
out that it sees a discontinuity which shouldn't have existed between
reg 0x278 and reg 0x280.
Discontinuity between last reg 0x0 and new reg 0x0, creating new region
Discontinuity between last reg 0x108 and new reg 0x200, creating new region
Discontinuity between last reg 0x278 and new reg 0x280, creating new region
Discontinuity between last reg 0x2b0 and new reg 0x400, creating new region
region of 67 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 31 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 13 contiguous counters starting with SYS:STAT:CNT[0x0a0]
region of 18 contiguous counters starting with SYS:STAT:CNT[0x100]
That is where TX_MM_HOLD should have been, and that was the bug, since
it was missing. After adding it, the regions look like this and the
off-by-one issue is resolved:
Discontinuity between last reg 0x000000 and new reg 0x000000, creating new region
Discontinuity between last reg 0x000108 and new reg 0x000200, creating new region
Discontinuity between last reg 0x0002b0 and new reg 0x000400, creating new region
region of 67 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 45 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 18 contiguous counters starting with SYS:STAT:CNT[0x100]
However, as I am thinking out loud, it should have not reported the
other counters as off by one even when skipping TX_MM_HOLD... after all,
on Ocelot/Seville, there are more counters which need to be skipped.
Which is when I investigated and noticed the bug solved in 2/3.
I've validated that both on native VSC9959 (which uses
ocelot_mm_stats_layout) as well as by faking the other switches by
making VSC9959 use the plain ocelot_stats_layout.
To summarize: on all Ocelot switches, the TX counters and drop counters
are completely broken. The RX counters are mostly fine.
With this occasion, I have collected more cleanup patches in this area,
which I'm going to submit after the net -> net-next merge.
====================
Vladimir Oltean [Tue, 21 Mar 2023 01:03:25 +0000 (03:03 +0200)]
net: mscc: ocelot: add TX_MM_HOLD to ocelot_mm_stats_layout
The lack of a definition for this counter is what initially prompted me
to investigate a problem which really manifested itself as the previous
change, "net: mscc: ocelot: fix transfer from region->buf to ocelot->stats".
When TX_MM_HOLD is defined in enum ocelot_stat but not in struct
ocelot_stat_layout ocelot_mm_stats_layout, this creates a hole, which
due to the aforementioned bug, makes all counters following TX_MM_HOLD
be recorded off by one compared to their correct position. So for
example, a non-zero TX_PMAC_OCTETS would be reported as TX_MERGE_FRAGMENTS,
TX_PMAC_UNICAST would be reported as TX_PMAC_OCTETS, TX_PMAC_64 would be
reported as TX_PMAC_PAUSE, etc etc. This is because the size of the hole
(1) is much smaller than the size of the region, so the phenomenon where
the stats are off-by-one, rather than lost, prevails.
However, the phenomenon where stats are lost can be seen too, for
example with DROP_LOCAL, which is at the beginning of its own region
(offset 0x000400 vs the previous 0x0002b0 constitutes a discontinuity).
This is also reported as off by one and saved to TX_PMAC_1527_MAX, but
that counter is not reported to the unstructured "ethtool -S", as
opposed to DROP_LOCAL which is (as "drop_local").
Fixes: ab3f97a9610a ("net: mscc: ocelot: export ethtool MAC Merge stats for Felix VSC9959") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Vladimir Oltean [Tue, 21 Mar 2023 01:03:24 +0000 (03:03 +0200)]
net: mscc: ocelot: fix transfer from region->buf to ocelot->stats
To understand the problem, we need some definitions.
The driver is aware of multiple counters (enum ocelot_stat), yet not all
switches supported by the driver implement all counters. There are 2
statistics layouts: ocelot_stats_layout and ocelot_mm_stats_layout, the
latter having 36 counters more than the former.
ocelot->stats[] is not a compact array, i.e. there are elements within
it which are not going to be populated for ocelot_stats_layout. On the
other hand, ocelot->stats[] is easily indexable, for example "tx_octets"
for port 3 can be found at ocelot->stats[3 * OCELOT_NUM_STATS +
OCELOT_STAT_TX_OCTETS], and that is why we keep it sparse.
Regions, as created by ocelot_prepare_stats_regions(), are compact
(every element from region->buf will correspond to a counter that is
present in this switch's layout) but are not easily indexable.
Let's define holes as the ranges of values of enum ocelot_stat for which
ocelot_stats_layout doesn't have a "reg" defined. For example, there is
a hole between OCELOT_STAT_RX_GREEN_PRIO_7 and OCELOT_STAT_TX_OCTETS
which is of 23 elements that are only present on ocelot_mm_stats_layout,
and as such, they are also present in enum ocelot_stat. Let's define the
left extremity of the hole - the last enum ocelot_stat still defined -
as A (in this case OCELOT_STAT_RX_GREEN_PRIO_7) and the right extremity -
the first enum ocelot_stat that is defined after a series of undefined
ones - as B (in this case OCELOT_STAT_TX_OCTETS).
There is a bug in the procedure which transfers stats from region->buf[]
to ocelot->stats[].
For each hole in the ocelot_stats_layout, the logic transfers the stats
starting with enum ocelot_stat B to ocelot->stats[] index A + 1. So all
stats after a hole are saved to a position which is off by B - A + 1
elements.
This causes 2 kinds of issues:
(a) counters which shouldn't increment increment
(b) counters which should increment don't
Holes in the ocelot_stat_layout automatically imply the end of a region
and the beginning of a new one; however the reverse is not necessarily
true. For example, for ocelot_mm_stat_layout, there could be multiple
regions (which indicate discontinuities in register addresses) while
there is no hole (which indicates discontinuities in enum ocelot_stat
values).
In the example above, the stats from the second region->buf[] are not
transferred to ocelot->stats starting with index
"port * OCELOT_NUM_STATS + OCELOT_STAT_TX_OCTETS" as they should, but
rather, starting with element
"port * OCELOT_NUM_STATS + OCELOT_STAT_RX_GREEN_PRIO_7 + 1".
That stats[] array element is not reported to user space for switches
that use ocelot_stat_layout, and that is how issue (b) occurs.
However, if the length of the second region is larger than the hole,
then some stats will start to be transferred to the ocelot->stats[]
indices which *are* reported to user space, but those indices contain
wrong values (corresponding to unexpected counters). This is how issue
(a) occurs.
The procedure, as it was introduced in commit d87b1c08f38a ("net: mscc:
ocelot: use bulk reads for stats"), was not buggy, because there were no
holes in the struct ocelot_stat_layout instances at that time. The
problem is that when those holes were introduced, the function was not
updated to take them into consideration.
To update the procedure, we need to know, for each region, which enum
ocelot_stat corresponds to its region->base. We have no way of deducing
that based on the contents of struct ocelot_stats_region, so we need to
add this information.
Fixes: ab3f97a9610a ("net: mscc: ocelot: export ethtool MAC Merge stats for Felix VSC9959") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Vladimir Oltean [Tue, 21 Mar 2023 01:03:23 +0000 (03:03 +0200)]
net: mscc: ocelot: fix stats region batching
The blamed commit changed struct ocelot_stat_layout :: "u32 offset" to
"u32 reg".
However, "u32 reg" is not quite a register address, but an enum
ocelot_reg, which in itself encodes an enum ocelot_target target in the
upper bits, and an index into the ocelot->map[target][] array in the
lower bits.
So, whereas the previous code comparison between stats_layout[i].offset
and last + 1 was correct (because those "offsets" at the time were
32-bit relative addresses), the new code, comparing layout[i].reg to
last + 4 is not correct, because the "reg" here is an enum/index, not an
actual register address.
What we want to compare are indeed register addresses, but to do that,
we need to actually go through the same motions as
__ocelot_bulk_read_ix() itself.
With this bug, all statistics counters are deemed by
ocelot_prepare_stats_regions() as constituting their own region.
(Truncated) log on VSC9959 (Felix) below (prints added by me):
Before:
region of 1 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x001]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x002]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x041]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x042]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x081]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x0ac]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x100]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x101]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x111]
After:
region of 67 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 45 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 18 contiguous counters starting with SYS:STAT:CNT[0x100]
Since commit d87b1c08f38a ("net: mscc: ocelot: use bulk reads for
stats") intended bulking as a performance improvement, and since now,
with trivial-sized regions, performance is even worse than without
bulking at all, this could easily qualify as a performance regression.
Fixes: d4c367650704 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset") Signed-off-by: Vladimir Oltean <[email protected]> Acked-by: Colin Foster <[email protected]> Tested-by: Colin Foster <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
The root cause is traced to the vc_maps which alloced in open_card_oam()
are not freed in close_card_oam(). The vc_maps are used to record
open connections, so when close a vc_map in close_card_oam(), the memory
should be freed. Moreover, the ubr0 is not closed when close a idt77252
device, leading to the memory leak of vc_map and scq_info.
Fix them by adding kfree in close_card_oam() and implementing new
close_card_ubr0() to close ubr0.
When BCM63xx internal switches are connected to switches with a 4-byte
Broadcom tag, it does not identify the packet as VLAN tagged, so it adds one
based on its PVID (which is likely 0).
Right now, the packet is received by the BCM63xx internal switch and the 6-byte
tag is properly processed. The next step would to decode the corresponding
4-byte tag. However, the internal switch adds an invalid VLAN tag after the
6-byte tag and the 4-byte tag handling fails.
In order to fix this we need to remove the invalid VLAN tag after the 6-byte
tag before passing it to the 4-byte tag decoding.
Dylan Jhong [Mon, 13 Mar 2023 03:49:06 +0000 (11:49 +0800)]
riscv: mm: Fix incorrect ASID argument when flushing TLB
Currently, we pass the CONTEXTID instead of the ASID to the TLB flush
function. We should only take the ASID field to prevent from touching
the reserved bit field.
Linus Torvalds [Tue, 21 Mar 2023 21:48:38 +0000 (14:48 -0700)]
Merge tag 'nfsd-6.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- Fix a crash during NFS READs from certain client implementations
- Address a minor kbuild regression in v6.3
* tag 'nfsd-6.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: don't replace page in rq_pages if it's a continuation of last page
NFS & NFSD: Update GSS dependencies
Maher Sanalla [Wed, 15 Mar 2023 09:04:38 +0000 (11:04 +0200)]
net/mlx5: Read the TC mapping of all priorities on ETS query
When ETS configurations are queried by the user to get the mapping
assignment between packet priority and traffic class, only priorities up
to maximum TCs are queried from QTCT register in FW to retrieve their
assigned TC, leaving the rest of the priorities mapped to the default
TC #0 which might be misleading.
Fix by querying the TC mapping of all priorities on each ETS query,
regardless of the maximum number of TCs configured in FW.
Emeel Hakim [Mon, 20 Mar 2023 11:13:55 +0000 (13:13 +0200)]
net/mlx5e: Overcome slow response for first macsec ASO WQE
First ASO WQE poll causes a cache miss in hardware hence the resut is
delayed. It causes to the situation where such WQE is polled earlier
than it is needed.
Roy Novich [Wed, 1 Mar 2023 13:47:11 +0000 (15:47 +0200)]
net/mlx5e: Initialize link speed to zero
mlx5e_port_max_linkspeed does not guarantee value assignment for speed.
Avoid cases where link_speed might be used uninitialized. In case
mlx5e_port_max_linkspeed fails, a default link speed of 50000 will be
used for the calculations.
Lama Kayal [Tue, 31 Jan 2023 12:07:03 +0000 (14:07 +0200)]
net/mlx5: Fix steering rules cleanup
vport's mc, uc and multicast rules are not deleted in teardown path when
EEH happens. Since the vport's promisc settings(uc, mc and all) in
firmware are reset after EEH, mlx5 driver will try to delete the above
rules in the initialization path. This cause kernel crash because these
software rules are no longer valid.
Fix by nullifying these rules right after delete to avoid accessing any dangling
pointers.
Gavin Li [Thu, 9 Feb 2023 10:48:52 +0000 (12:48 +0200)]
net/mlx5e: Block entering switchdev mode with ns inconsistency
Upon entering switchdev mode, VF/SF representors are spawned in the
devlink instance's net namespace, whereas the PF net device transforms
into the uplink representor, remaining in the net namespace the PF net
device was in. Therefore, if a PF net device's namespace is different from
its parent devlink net namespace, entering switchdev mode can create an
illegal situation where all representors sharing the same core device
are NOT in the same net namespace.
To avoid this issue, block entering switchdev mode for devices whose child
netdev net namespace has diverged from the parent devlink's.
Fixes: 7768d1971de6 ("net/mlx5: E-Switch, Add control for encapsulation") Signed-off-by: Gavin Li <[email protected]> Reviewed-by: Gavi Teitz <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
Gavin Li [Fri, 25 Nov 2022 02:15:40 +0000 (04:15 +0200)]
net/mlx5e: Set uplink rep as NETNS_LOCAL
Previously, NETNS_LOCAL was not set for uplink representors, inconsistent
with VF representors, and allowed the uplink representor to be moved
between net namespaces and separated from the VF representors it shares
the core device with. Such usage would break the isolation model of
namespaces, as devices in different namespaces would have access to
shared memory.
To solve this issue, set NETNS_LOCAL for uplink representors if eswitch is
in switchdev mode.
Fixes: 7a9fb35e8c3a ("net/mlx5e: Do not reload ethernet ports when changing eswitch mode") Signed-off-by: Gavin Li <[email protected]> Reviewed-by: Gavi Teitz <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
Daniel Borkmann [Mon, 20 Mar 2023 14:37:25 +0000 (15:37 +0100)]
bpf: Adjust insufficient default bpf_jit_limit
We've seen recent AWS EKS (Kubernetes) user reports like the following:
After upgrading EKS nodes from v20230203 to v20230217 on our 1.24 EKS
clusters after a few days a number of the nodes have containers stuck
in ContainerCreating state or liveness/readiness probes reporting the
following error:
Readiness probe errored: rpc error: code = Unknown desc = failed to
exec in container: failed to start exec "4a11039f730203ffc003b7[...]":
OCI runtime exec failed: exec failed: unable to start container process:
unable to init seccomp: error loading seccomp filter into kernel:
error loading seccomp filter: errno 524: unknown
However, we had not been seeing this issue on previous AMIs and it only
started to occur on v20230217 (following the upgrade from kernel 5.4 to
5.10) with no other changes to the underlying cluster or workloads.
We tried the suggestions from that issue (sysctl net.core.bpf_jit_limit=452534528)
which helped to immediately allow containers to be created and probes to
execute but after approximately a day the issue returned and the value
returned by cat /proc/vmallocinfo | grep bpf_jit | awk '{s+=$2} END {print s}'
was steadily increasing.
I tested bpf tree to observe bpf_jit_charge_modmem, bpf_jit_uncharge_modmem
their sizes passed in as well as bpf_jit_current under tcpdump BPF filter,
seccomp BPF and native (e)BPF programs, and the behavior all looks sane
and expected, that is nothing "leaking" from an upstream perspective.
The bpf_jit_limit knob was originally added in order to avoid a situation
where unprivileged applications loading BPF programs (e.g. seccomp BPF
policies) consuming all the module memory space via BPF JIT such that loading
of kernel modules would be prevented. The default limit was defined back in
2018 and while good enough back then, we are generally seeing far more BPF
consumers today.
Adjust the limit for the BPF JIT pool from originally 1/4 to now 1/2 of the
module memory space to better reflect today's needs and avoid more users
running into potentially hard to debug issues.
Linus Torvalds [Tue, 21 Mar 2023 18:38:58 +0000 (11:38 -0700)]
Merge tag 'keys-fixes-20230321' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull keyrings fixes from David Howells:
- Fix request_key() so that it doesn't cache a looked up key on the
current thread if that thread is a kernel thread.
The cache is cleared during notify_resume - but that doesn't happen
in kernel threads. This is causing cifs DNS keys to be
un-invalidateable.
- Fix a wrapper check in verify_pefile() to not round up the length.
- Change asymmetric_keys code to log errors to make it easier for users
to work out why failures occurred.
* tag 'keys-fixes-20230321' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
asymmetric_keys: log on fatal failures in PE/pkcs7
verify_pefile: relax wrapper length check
keys: Do not cache key in task struct if key is requested from kernel thread
During reboot all drivers PM shutdown callbacks are invoked.
In iavf_shutdown() the adapter state is changed to __IAVF_REMOVE.
In ice_shutdown() the call chain above is executed, which at some point
calls iavf_remove(). However iavf_remove() expects the VF to be in one
of the states __IAVF_RUNNING, __IAVF_DOWN or __IAVF_INIT_FAILED. If
that's not the case it sleeps forever.
So if iavf_shutdown() gets invoked before iavf_remove() the system will
hang indefinitely because the adapter is already in state __IAVF_REMOVE.
Fix this by returning from iavf_remove() if the state is __IAVF_REMOVE,
as we already went through iavf_shutdown().
Fixes: 974578017fc1 ("iavf: Add waiting so the port is initialized in remove") Fixes: a8417330f8a5 ("iavf: Fix race condition between iavf_shutdown and iavf_remove") Reported-by: Marius Cornea <[email protected]> Signed-off-by: Stefan Assmann <[email protected]> Reviewed-by: Michal Kubiak <[email protected]> Tested-by: Rafal Romanowski <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
Filters shouldn't be removed in VSI rebuild path. Removing them on PF
VSI results in no rule for PF MAC after changing for example queues
amount.
Remove all filters only in the VSI remove flow. As unload should also
cause the filter to be removed introduce, a new function ice_stop_eth().
It will unroll ice_start_eth(), so remove filters and close VSI.
Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Signed-off-by: Michal Swiatkowski <[email protected]> Tested-by: Arpana Arland <[email protected]> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <[email protected]>
Piotr Raczynski [Thu, 9 Mar 2023 21:38:56 +0000 (13:38 -0800)]
ice: fix rx buffers handling for flow director packets
Adding flow director filters stopped working correctly after
commit 2fba7dc5157b ("ice: Add support for XDP multi-buffer
on Rx side"). As a result, only first flow director filter
can be added, adding next filter leads to NULL pointer
dereference attached below.
Rx buffer handling and reallocation logic has been optimized,
however flow director specific traffic was not accounted for.
As a result driver handled those packets incorrectly since new
logic was based on ice_rx_ring::first_desc which was not set
in this case.
Fix this by setting struct ice_rx_ring::first_desc to next_to_clean
for flow director received packets.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side") Signed-off-by: Piotr Raczynski <[email protected]> Acked-by: Maciej Fijalkowski <[email protected]> Reviewed-by: Simon Horman <[email protected]> Tested-by: Arpana Arland <[email protected]> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <[email protected]>
Robbie Harwood [Mon, 20 Feb 2023 17:12:54 +0000 (12:12 -0500)]
asymmetric_keys: log on fatal failures in PE/pkcs7
These particular errors can be encountered while trying to kexec when
secureboot lockdown is in place. Without this change, even with a
signed debug build, one still needs to reboot the machine to add the
appropriate dyndbg parameters (since lockdown blocks debugfs).
Accordingly, upgrade all pr_debug() before fatal error into pr_warn().
Robbie Harwood [Mon, 20 Feb 2023 17:12:53 +0000 (12:12 -0500)]
verify_pefile: relax wrapper length check
The PE Format Specification (section "The Attribute Certificate Table
(Image Only)") states that `dwLength` is to be rounded up to 8-byte
alignment when used for traversal. Therefore, the field is not required
to be an 8-byte multiple in the first place.
Accordingly, pesign has not performed this alignment since version
0.110. This causes kexec failure on pesign'd binaries with "PEFILE:
Signature wrapper len wrong". Update the comment and relax the check.
David Howells [Tue, 14 Mar 2023 15:15:18 +0000 (15:15 +0000)]
keys: Do not cache key in task struct if key is requested from kernel thread
The key which gets cached in task structure from a kernel thread does not
get invalidated even after expiry. Due to which, a new key request from
kernel thread will be served with the cached key if it's present in task
struct irrespective of the key validity. The change is to not cache key in
task_struct when key requested from kernel thread so that kernel thread
gets a valid key on every key request.
The problem has been seen with the cifs module doing DNS lookups from a
kernel thread and the results getting pinned by being attached to that
kernel thread's cache - and thus not something that can be easily got rid
of. The cache would ordinarily be cleared by notify-resume, but kernel
threads don't do that.
This isn't seen with AFS because AFS is doing request_key() within the
kernel half of a user thread - which will do notify-resume.
Since commit 6c40624930c5 ("bootconfig: Increase max nodes of bootconfig
from 1024 to 8192 for DCC support") increased the max number of bootconfig
node to 8192, the bootconfig testcase of the max number of nodes fails.
To fix this issue, we can not simply increase the number in the test script
because the test bootconfig file becomes too big (>32KB). To fix that, we
can use a combination of three alphabets (26^3 = 17576). But with that,
we can not express the 8193 (just one exceed from the limitation) because
it also exceeds the max size of bootconfig. So, the first 26 nodes will just
use one alphabet.
With this fix, test-bootconfig.sh passes all tests.
projects / linux.git / log