Boris Brezillon [Sun, 8 Feb 2015 18:23:42 +0000 (19:23 +0100)]
pinctrl: at91: move lock/unlock_as_irq calls into request/release
The gpiochip_lock_as_irq call can fail and return an error,
while the irq_startup is not expected to fail (returns an
unsigned int which is not checked by irq core code).
irq_request/release_resources functions have been created
to address this problem.
Move gpiochip_lock/unlock_as_irq calls into
irq_request/release_resources functions to prevent using a
gpio as an irq if the gpiochip_lock_as_irq call failed.
Josef Bacik [Tue, 17 Mar 2015 14:52:28 +0000 (10:52 -0400)]
Btrfs: fix outstanding_extents accounting in DIO
We are keeping track of how many extents we need to reserve properly based on
the amount we want to write, but we were still incrementing outstanding_extents
if we wrote less than what we requested. This isn't quite right since we will
be limited to our max extent size. So instead lets do something horrible! Keep
track of how many outstanding_extents we reserved, and decrement each time we
allocate an extent. If we use our entire reserve make sure to jack up
outstanding_extents on the inode so the accounting works out properly. Thanks,
Josef Bacik [Mon, 16 Mar 2015 21:38:52 +0000 (17:38 -0400)]
Btrfs: add sanity test for outstanding_extents accounting
I introduced a regression wrt outstanding_extents accounting. These are tricky
areas that aren't easily covered by xfstests as we could change MAX_EXTENT_SIZE
at any time. So add sanity tests to cover the various conditions that are
tricky in order to make sure we don't introduce regressions in the future.
Thanks,
Linus Torvalds [Tue, 17 Mar 2015 20:32:17 +0000 (13:32 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes from all around the place:
- a KASLR related revert where we ran out of time to get a fix - this
represents a substantial portion of the diffstat,
- two FPU fixes,
- two x86 platform fixes: an ACPI reduced-hw fix and a NumaChip fix,
- an entry code fix,
- and a VDSO build fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "x86/mm/ASLR: Propagate base load address calculation"
x86/fpu: Drop_fpu() should not assume that tsk equals current
x86/fpu: Avoid math_state_restore() without used_math() in __restore_xstate_sig()
x86/apic/numachip: Fix sibling map with NumaChip
x86/platform, acpi: Bypass legacy PIC and PIT in ACPI hardware reduced mode
x86/asm/entry/32: Fix user_mode() misuses
x86/vdso: Fix the build on GCC5
Josef Bacik [Mon, 16 Mar 2015 21:38:02 +0000 (17:38 -0400)]
Btrfs: just free dummy extent buffers
If we fail during our sanity tests we could get NULL deref's because we unload
the module before the dummy extent buffers are free'd via RCU. So check for
this case and just free the things directly. Thanks,
Josef Bacik [Fri, 13 Mar 2015 19:01:24 +0000 (15:01 -0400)]
Btrfs: account merges/splits properly
My fix
Btrfs: fix merge delalloc logic
only fixed half of the problems, it didn't fix the case where we have two large
extents on either side and then join them together with a new small extent. We
need to instead keep track of how many extents we have accounted for with each
side of the new extent, and then see how many extents we need for the new large
extent. If they match then we know we need to keep our reservation, otherwise
we need to drop our reservation. This shows up with a case like this
Previously the logic would have said that the number extents required for the
new size (3) is larger than the number of extents required for the largest side
(2) therefore we need to keep our reservation. But this isn't the case, since
both sides require a reservation of 2 which leads to 4 for the whole range
currently reserved, but we only need 3, so we need to drop one of the
reservations. The same problem existed for splits, we'd think we only need 3
extents when creating the hole but in reality we need 4. Thanks,
Linus Torvalds [Tue, 17 Mar 2015 20:22:29 +0000 (13:22 -0700)]
Merge branches 'perf-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf and timer fixes from Ingo Molnar:
"Two small perf fixes:
- kernel side context leak fix
- tooling crash fix
And two clocksource driver fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix context leak in put_event()
perf annotate: Fix fallback to unparsed disassembler line
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: sun5i: Fix setup_irq init sequence
clocksource: efm32: Fix a NULL pointer dereference
Robert Jarzmik [Thu, 12 Feb 2015 16:59:10 +0000 (17:59 +0100)]
Revert "smc91x: retrieve IRQ and trigger flags in a modern way"
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Nicolas Dichtel [Mon, 16 Mar 2015 14:56:05 +0000 (15:56 +0100)]
ip6_tunnel: fix error code when tunnel exists
After commit 2b0bb01b6edb, the kernel returns -ENOBUFS when user tries to add
an existing tunnel with ioctl API:
$ ip -6 tunnel add ip6tnl1 mode ip6ip6 dev eth1
add tunnel "ip6tnl0" failed: No buffer space available
It's confusing, the right error is EEXIST.
This patch also change a bit the code returned:
- ENOBUFS -> ENOMEM
- ENOENT -> ENODEV
Fixes: 2b0bb01b6edb ("ip6_tunnel: Return an error when adding an existing tunnel.") CC: Steffen Klassert <[email protected]> Reported-by: Pierre Cheynier <[email protected]> Signed-off-by: Nicolas Dichtel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Tue, 17 Mar 2015 17:47:06 +0000 (10:47 -0700)]
Merge tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"The two main fixes here from Javier and Doug both fix issues seen on
the Exynos-based ARM Chromebooks with reference counting of GPIO
regulators over system suspend. The GPIO enable code didn't properly
take account of this case (a full analysis is in Doug's commit log).
This is fixed by both fixing the reference counting directly and by
making the resume code skip enables it doesn't need to do. We could
skip the change in the resume code but it's a very simple change and
adds extra robustness against problems in other drivers"
* tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps65910: Add missing #include <linux/of.h>
regulator: core: Fix enable GPIO reference counting
regulator: Only enable disabled regulators on resume
Linus Torvalds [Tue, 17 Mar 2015 17:41:26 +0000 (10:41 -0700)]
Merge tag 'regmap-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A few things here:
- a change from Lars to fix insertion of cache values at the start of
rather than end of a rbtree block. This hadn't been noticed before
since almost everything lists registers in ascending order.
- a fix from Takashi for spurious warnings during cache sync with
read once registers, a problem which can be very noticeable on
devices that it affects.
- a fix from Valentin for a tighening of the oneshot IRQ request
interface which would have broken affected devices"
* tag 'regmap-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: regcache-rbtree: Fix present bitmap resize
regmap: Skip read-only registers in regcache_sync()
regmap-irq: set IRQF_ONESHOT flag to ensure IRQ request
Linus Torvalds [Tue, 17 Mar 2015 17:36:01 +0000 (10:36 -0700)]
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"Not entirely surprising: the ongoing QEMU work on virtio 1.0 has
revealed more minor issues with our virtio 1.0 drivers just introduced
in the kernel.
(I would normally use my fixes branch for this, but there were a batch
of them...)"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_mmio: fix access width for mmio
uapi/virtio_scsi: allow overriding CDB/SENSE size
virtio_mmio: generation support
virtio_rpmsg: set DRIVER_OK before using device
9p/trans_virtio: fix hot-unplug
virtio-balloon: do not call blocking ops when !TASK_RUNNING
virtio_blk: fix comment for virtio 1.0
virtio_blk: typo fix
virtio_balloon: set DRIVER_OK before using device
virtio_console: avoid config access from irq
virtio_console: init work unconditionally
Linus Torvalds [Tue, 17 Mar 2015 17:31:36 +0000 (10:31 -0700)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Marcelo Tosatti:
"KVM bug fixes (ARM and x86)"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm/arm64: KVM: Keep elrsr/aisr in sync with software model
KVM: VMX: Set msr bitmap correctly if vcpu is in guest mode
arm/arm64: KVM: fix missing unlock on error in kvm_vgic_create()
kvm: x86: i8259: return initialized data on invalid-size read
arm64: KVM: Fix outdated comment about VTCR_EL2.PS
arm64: KVM: Do not use pgd_index to index stage-2 pgd
arm64: KVM: Fix stage-2 PGD allocation to have per-page refcounting
kvm: move advertising of KVM_CAP_IRQFD to common code
pagemap: do not leak physical addresses to non-privileged userspace
As pointed by recent post[1] on exploiting DRAM physical imperfection,
/proc/PID/pagemap exposes sensitive information which can be used to do
attacks.
This disallows anybody without CAP_SYS_ADMIN to read the pagemap.
Takashi Iwai [Tue, 17 Mar 2015 15:30:26 +0000 (16:30 +0100)]
Merge tag 'asoc-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.0
As well as the usual collection of driver specific fixes there's a few
more generic things:
- Lots of fixes from Takashi for drivers using the wrong field in the
control union to communicate with userspace, leading to potential
errors on 64 bit systems.
- A fix from Lars for locking of the lists of devices we maintain,
mostly only likely to trigger during device probe and removal.
Josef Bacik [Mon, 2 Mar 2015 21:37:31 +0000 (16:37 -0500)]
Btrfs: prepare block group cache before writing
Writing the block group cache will modify the extent tree quite a bit because it
truncates the old space cache and pre-allocates new stuff. To try and cut down
on the churn lets do the setup dance first, then later on hopefully we can avoid
looping with newly dirtied roots. Thanks,
Petr Mladek [Thu, 12 Mar 2015 11:55:13 +0000 (12:55 +0100)]
livepatch: Fix subtle race with coming and going modules
There is a notifier that handles live patches for coming and going modules.
It takes klp_mutex lock to avoid races with coming and going patches but
it does not keep the lock all the time. Therefore the following races are
possible:
1. The notifier is called sometime in STATE_MODULE_COMING. The module
is visible by find_module() in this state all the time. It means that
new patch can be registered and enabled even before the notifier is
called. It might create wrong order of stacked patches, see below
for an example.
2. New patch could still see the module in the GOING state even after
the notifier has been called. It will try to initialize the related
object structures but the module could disappear at any time. There
will stay mess in the structures. It might even cause an invalid
memory access.
This patch solves the problem by adding a boolean variable into struct module.
The value is true after the coming and before the going handler is called.
New patches need to be applied when the value is true and they need to ignore
the module when the value is false.
Note that we need to know state of all modules on the system. The races are
related to new patches. Therefore we do not know what modules will get
patched.
Also note that we could not simply ignore going modules. The code from the
module could be called even in the GOING state until mod->exit() finishes.
If we start supporting patches with semantic changes between function
calls, we need to apply new patches to any still usable code.
See below for an example.
Finally note that the patch solves only the situation when a new patch is
registered. There are no such problems when the patch is being removed.
It does not matter who disable the patch first, whether the normal
disable_patch() or the module notifier. There is nothing to do
once the patch is disabled.
Alternative solutions:
======================
+ reject new patches when a patched module is coming or going; this is ugly
+ wait with adding new patch until the module leaves the COMING and GOING
states; this might be dangerous and complicated; we would need to release
kgr_lock in the middle of the patch registration to avoid a deadlock
with the coming and going handlers; also we might need a waitqueue for
each module which seems to be even bigger overhead than the boolean
+ stop modules from entering COMING and GOING states; wait until modules
leave these states when they are already there; looks complicated; we would
need to ignore the module that asked to stop the others to avoid a deadlock;
also it is unclear what to do when two modules asked to stop others and
both are in COMING state (situation when two new patches are applied)
+ always register/enable new patches and fix up the potential mess (registered
patches order) in klp_module_init(); this is nasty and prone to regressions
in the future development
+ add another MODULE_STATE where the kallsyms are visible but the module is not
used yet; this looks too complex; the module states are checked on "many"
locations
Example of patch stacking breakage:
===================================
The notifier could _not_ _simply_ ignore already initialized module objects.
For example, let's have three patches (P1, P2, P3) for functions a() and b()
where a() is from vmcore and b() is from a module M. Something like:
a() b()
P1 a1() b1()
P2 a2() b2()
P3 a3() b3(3)
If you load the module M after all patches are registered and enabled.
The ftrace ops for function a() and b() has listed the functions in this
order:
, so the pointer to b3() is the first and will be used.
Then you might have the following scenario. Let's start with state when patches
P1 and P2 are registered and enabled but the module M is not loaded. Then ftrace
ops for b() does not exist. Then we get into the following race:
Going over the virtio mmio code, I noticed that it doesn't correctly
access modern device config values using "natural" accessors: it uses
readb to get/set them byte by byte, while the virtio 1.0 spec explicitly states:
The driver MUST only use 32 bit wide and aligned reads and writes to
access the control registers described in table 4.1.
For the device-specific configuration space, the driver MUST use
8 bit wide accesses for 8 bit wide fields, 16 bit wide and aligned
accesses for 16 bit wide fields and 32 bit wide and aligned accesses for
32 and 64 bit wide fields.
Borrow code from virtio_pci_modern to do this correctly.
Dave Airlie [Tue, 17 Mar 2015 00:54:24 +0000 (10:54 +1000)]
Merge branch 'linux-4.0' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
nouveau fixes, and gm206 modesetting enables.
* 'linux-4.0' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix i2c table parsing for dcb 4.1
drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
Ben Skeggs [Tue, 27 Jan 2015 05:09:39 +0000 (15:09 +1000)]
drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
Complete bong hit (and not the last...), the hardware will reassert the
interrupt to PMC if it's necessary.
Also potentially harmful in the face of interrupts such as the non-stall
interrupt, which remain active in NV_PFIFO_INTR even when we don't care
about servicing it.
It appears (hopefully, fdo#87244), that under certain loads, the methods
may pass quickly enough to hit the "100 spins and kill PFIFO" thing that
we had going on. Not ideal ;)
Marcelo Tosatti [Mon, 16 Mar 2015 23:08:56 +0000 (20:08 -0300)]
Merge tag 'kvm-arm-fixes-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
Fixes for KVM/ARM for 4.0-rc5.
Fixes page refcounting issues in our Stage-2 page table management code,
fixes a missing unlock in a gicv3 error path, and fixes a race that can
cause lost interrupts if signals are pending just prior to entering the
guest.
Ben Goz [Sun, 8 Mar 2015 12:15:16 +0000 (14:15 +0200)]
drm/radeon: Changing number of compute pipe lines
The current CP firmware can handle Usermode Queues only on MEC1.
To reflect this firmware change, this commit reduces number of compute pipelines
to 4 - 1, from 8 - 1 (the first pipeline is allocated for kgd).
Ben Goz [Sun, 8 Mar 2015 12:17:02 +0000 (14:17 +0200)]
drm/amdkfd: destroy mqd when destroying kernel queue
This patch adds a missing destruction of mqd, when destroying a kernel queue.
Without the destruction, there is a memory leakage when repeatedly creating and
destroying kernel queues.
Michal Schmidt [Mon, 16 Mar 2015 15:15:59 +0000 (16:15 +0100)]
bnx2x: fix encapsulation features on 57710/57711
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
JeHyeon Yeon [Mon, 16 Mar 2015 01:03:19 +0000 (01:03 +0000)]
LZ4 : fix the data abort issue
If the part of the compression data are corrupted, or the compression
data is totally fake, the memory access over the limit is possible.
This is the log from my system usning lz4 decompression.
[6502]data abort, halting
[6503]r0 0x00000000 r1 0x00000000 r2 0xdcea0ffc r3 0xdcea0ffc
[6509]r4 0xb9ab0bfd r5 0xdcea0ffc r6 0xdcea0ff8 r7 0xdce80000
[6515]r8 0x00000000 r9 0x00000000 r10 0x00000000 r11 0xb9a98000
[6522]r12 0xdcea1000 usp 0x00000000 ulr 0x00000000 pc 0x820149bc
[6528]spsr 0x400001f3
and the memory addresses of some variables at the moment are
ref:0xdcea0ffc, op:0xdcea0ffc, oend:0xdcea1000
As you can see, COPYLENGH is 8bytes, so @ref and @op can access the momory
over @oend.
NeilBrown [Sun, 15 Mar 2015 23:44:52 +0000 (10:44 +1100)]
kernfs: handle poll correctly on 'direct_read' files.
Kernfs supports two styles of read: direct_read and seqfile_read.
The latter supports 'poll' correctly thanks to the update of
'->event' in kernfs_seq_show.
The former does not as '->event' is never updated on a read.
So add an appropriate update in kernfs_file_direct_read().
This was noticed because some 'md' sysfs attributes were
recently changed to use direct reads.
David S. Miller [Mon, 16 Mar 2015 20:17:48 +0000 (16:17 -0400)]
Merge tag 'mac80211-for-davem-2015-03-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are a few fixes that I'd like to still get in:
* disable U-APSD for better interoperability, from Michal Kazior
* drop unencrypted frames in mesh forwarding, from Bob Copeland
* treat non-QoS/WMM HT stations as non-HT, to fix confusion when
they connect and then get QoS packets anyway due to HT
* fix counting interfaces for combination checks, otherwise the
interface combinations aren't properly enforced (from Andrei)
* fix pure ECSA by reacting to the IE change
* ignore erroneous (E)CSA to the current channel which sometimes
happens due to AP/GO bugs
====================
1) Fix the network header offset in _decode_session6
when multiple IPv6 extension headers are present.
From Hajime Tazaki.
2) Fix an interfamily tunnel crash. We set outer mode
protocol too early and may dispatch to the wrong
address family. Move the setting of the outer mode
protocol behind the last accessing of the inner mode
to fix the crash.
3) Most callers of xfrm_lookup() expect that dst_orig
is released on error. But xfrm_lookup_route() may
need dst_orig to handle certain error cases. So
introduce a flag that tells what should be done in
case of error. From Huaibin Wang.
Please pull or let me know if there are problems.
====================
Andy Shevchenko [Mon, 9 Mar 2015 10:16:42 +0000 (12:16 +0200)]
dmaengine: dw: append MODULE_ALIAS for platform driver
The commit 9cade1a46c77 (dma: dw: split driver to library part and platform
code) introduced a separate platform driver but missed to add a
MODULE_ALIAS("platform:dw_dmac"); to that module.
The patch adds this to get driver loaded automatically if platform device is
registered.
Reported-by: "Blin, Jerome" <[email protected]> Fixes: 9cade1a46c77 (dma: dw: split driver to library part and platform code) Signed-off-by: Andy Shevchenko <[email protected]> Signed-off-by: Vinod Koul <[email protected]>
Slot 0 and 1 gets inverted in the second report above, which
introduces a cursor jump. The problem is that this cursor jump is
often enough to leave the current widget, and X sends the
scrolling events to whoever is now under the cursor.
Takashi Iwai [Mon, 16 Mar 2015 09:18:08 +0000 (10:18 +0100)]
ALSA: hda - Treat stereo-to-mono mix properly
The commit [ef403edb7558: ALSA: hda - Don't access stereo amps for
mono channel widgets] fixed the handling of mono widgets in general,
but it still misses an exceptional case: namely, a mono mixer widget
taking a single stereo input. In this case, it has stereo volumes
although it's a mono widget, and thus we have to take care of both
left and right input channels, as stated in HD-audio spec ("7.1.3
Widget Interconnection Rules").
This patch covers this missing piece by adding proper checks of stereo
amps in both the generic parser and the proc output codes.
drivers/regulator/tps65910-regulator.c: In function ‘tps65910_parse_dt_reg_data’:
drivers/regulator/tps65910-regulator.c:1018: error: implicit declaration of function ‘of_get_child_by_name’
drivers/regulator/tps65910-regulator.c:1018: warning: assignment makes pointer from integer without a cast
drivers/regulator/tps65910-regulator.c:1034: error: implicit declaration of function ‘of_node_put’
drivers/regulator/tps65910-regulator.c:1056: error: implicit declaration of function ‘of_property_read_u32’
Robin Gong [Sun, 15 Feb 2015 02:00:35 +0000 (10:00 +0800)]
dmaengine: imx-sdma: switch to dynamic context mode after script loaded
Below comments got from Page4724 of Reference Manual of i.mx6q:
http://cache.freescale.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf
--"Static context mode should be used for the first channel called
after reset to ensure that the all context RAM for that channel is
initialized during the context SAVE phase when the channel is
done or yields. Subsequent calls to the same channel or
different channels may use any of the dynamic context modes.
This will ensure that all context locations for the bootload
channel are initialized, and prevent undefined values in context
RAM from being loaded during the context restore if the
channel is re-started later"
Borislav Petkov [Mon, 16 Mar 2015 10:06:28 +0000 (11:06 +0100)]
Revert "x86/mm/ASLR: Propagate base load address calculation"
This reverts commit:
f47233c2d34f ("x86/mm/ASLR: Propagate base load address calculation")
The main reason for the revert is that the new boot flag does not work
at all currently, and in order to make this work, we need non-trivial
changes to the x86 boot code which we didn't manage to get done in
time for merging.
And even if we did, they would've been too risky so instead of
rushing things and break booting 4.1 on boxes left and right, we
will be very strict and conservative and will take our time with
this to fix and test it properly.
Xi Ruoyao [Thu, 12 Mar 2015 12:16:32 +0000 (20:16 +0800)]
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
plane->state->fb and plane->fb should always reference the same FB so
that atomic and legacy codepaths have the same view of display state.
However, there are some places in kernel code that directly set
plane->fb and neglect to update plane->state->fb. If we never do a
successful update through the atomic pipeline, the RmFB cleanup code
will look at the plane->state->fb pointer, which has never actually
been set to a legitimate value, and try to clean it up, leading to
BUG's.
Add a quick helper function to synchronize plane->state->fb with
plane->fb and call it everywhere the driver tries to manually set
plane->fb outside of the atomic pipeline. In this function, use
drm_atomic_set_fb_for_plane instead of writing plane->state->fb
directly to keep the reference count right.
This is modified from Matt Roper's patch to drm-intel-nightly with
commit id
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
However this bug exists in mainline kernel too, so I created this to fix
it in mainline kernel.
A minor change is to use drm_atomic_set_fb_for_plane instead of update
reference count manually.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88909
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93711 Signed-off-by: Xi Ruoyao <[email protected]> Reviewed-by: Matt Roper <[email protected]>
[Jani: included the patch notes in the commit message] Signed-off-by: Jani Nikula <[email protected]>
Johannes Berg [Thu, 12 Mar 2015 06:53:26 +0000 (08:53 +0200)]
mac80211: ignore CSA to same channel
If the AP is confused and starts doing a CSA to the same channel,
just ignore that request instead of trying to act it out since it
was likely sent in error anyway.
In the case of the bug I was investigating the GO was misbehaving
and sending out a beacon with CSA IEs still included after having
actually done the channel switch.
Johannes Berg [Thu, 12 Mar 2015 06:53:27 +0000 (08:53 +0200)]
nl80211: ignore HT/VHT capabilities without QoS/WMM
As HT/VHT depend heavily on QoS/WMM, it's not a good idea to
let userspace add clients that have HT/VHT but not QoS/WMM.
Since it does so in certain cases we've observed (client is
using HT IEs but not QoS/WMM) just ignore the HT/VHT info at
this point and don't pass it down to the drivers which might
unconditionally use it.
Johannes Berg [Thu, 12 Mar 2015 06:53:29 +0000 (08:53 +0200)]
mac80211: ask for ECSA IE to be considered for beacon parse CRC
When a beacon from the AP contains only the ECSA IE, and not a CSA IE
as well, this ECSA IE is not considered for calculating the CRC and
the beacon might be dropped as not being interesting. This is clearly
wrong, it should be handled and the channel switch should be executed.
Fix this by including the ECSA IE ID in the bitmap of interesting IEs.
mac80211: count interfaces correctly for combination checks
Since moving the interface combination checks to mac80211, it's
broken because it now only considers interfaces with an assigned
channel context, so for example any interface that isn't active
can still be up, which is clearly an issue; also, in particular
P2P-Device wdevs are an issue since they never have a chanctx.
Fix this by counting running interfaces instead the ones with a
channel context assigned.
Cc: [email protected] [3.16+] Fixes: 73de86a38962b ("cfg80211/mac80211: move interface counting for combination check to mac80211") Signed-off-by: Andrei Otcheretianski <[email protected]> Signed-off-by: Emmanuel Grumbach <[email protected]>
[rewrite commit message, dig out the commit it fixes] Signed-off-by: Johannes Berg <[email protected]>
Kernel faults are expected to handle OOM conditions gracefully (gup,
uaccess etc.), so they should never invoke the OOM killer. Reserve
this for faults triggered in user context when it is the only option.
Tobias Klauser [Fri, 13 Mar 2015 08:40:06 +0000 (16:40 +0800)]
nios2: Remove ucontext.h from exported arch headers
Commit 92d5dd8cd6e2 ("nios2: update pt_regs") removed the nios2 specific
ucontext.h, replacing it with the version from asm-generic. Thus it's no
longer necessary to include ucontext.h in exported headers.
Al Viro [Sat, 14 Mar 2015 05:34:56 +0000 (05:34 +0000)]
rxrpc: bogus MSG_PEEK test in rxrpc_recvmsg()
[I would really like an ACK on that one from dhowells; it appears to be
quite straightforward, but...]
MSG_PEEK isn't passed to ->recvmsg() via msg->msg_flags; as the matter of
fact, neither the kernel users of rxrpc, nor the syscalls ever set that bit
in there. It gets passed via flags; in fact, another such check in the same
function is done correctly - as flags & MSG_PEEK.
It had been that way (effectively disabled) for 8 years, though, so the patch
needs beating up - that case had never been tested. If it is correct, it's
-stable fodder.
Al Viro [Sat, 14 Mar 2015 05:22:21 +0000 (05:22 +0000)]
caif: fix MSG_OOB test in caif_seqpkt_recvmsg()
It should be checking flags, not msg->msg_flags. It's ->sendmsg()
instances that need to look for that in ->msg_flags, ->recvmsg() ones
(including the other ->recvmsg() instance in that file, as well as
unix_dgram_recvmsg() this one claims to be imitating) check in flags.
Braino had been introduced in commit dcda13 ("caif: Bugfix - use MSG_TRUNC
in receive") back in 2010, so it goes quite a while back.
Linus Torvalds [Sun, 15 Mar 2015 22:07:08 +0000 (15:07 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework fixes from Michael Turquette:
"The clk fixes for 4.0-rc4 comprise three themes.
First are the usual driver fixes for new regressions since v3.19.
Second are fixes to the common clock divider type caused by recent
changes to how we round clock rates. This affects many clock drivers
that use this common code.
Finally there are fixes for drivers that improperly compared struct
clk pointers (drivers must not deref these pointers). While some of
these drivers have done this for a long time, this did not cause a
problem until we started generating unique struct clk pointers for
every consumer. A new function, clk_is_match was introduced to get
these drivers working again and they are fixed up to no longer deref
the pointers themselves"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
ASoC: kirkwood: fix struct clk pointer comparing
ASoC: fsl_spdif: fix struct clk pointer comparing
ARM: imx: fix struct clk pointer comparing
clk: introduce clk_is_match
clk: don't export static symbol
clk: divider: fix calculation of initial best divider when rounding to closest
clk: divider: fix selection of divider when rounding to closest
clk: divider: fix calculation of maximal parent rate for a given divider
clk: divider: return real rate instead of divider value
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: Add PLL4 vote clock
clk: qcom: lcc-msm8960: Fix PLL rate detection
clk: qcom: Fix slimbus n and m val offsets
clk: ti: Fix FAPLL parent enable bit handling
Linus Torvalds [Sun, 15 Mar 2015 17:49:38 +0000 (10:49 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather unpleasantly large set of bug fixes for arm-soc, Most
of them because of cross-tree dependencies for Exynos where we should
have figured out the right path to merge things before the merge
window, and then the maintainer being unable to sort things out in
time during a business trip.
The other changes contained here are the usual collection:
MAINTAINERS file updates
- Gregory Clement is now a co-maintainer for the legacy Marvell EBU
platforms
- A MAINTAINERS entry for the Freescale Vybrid platform that was
added last year
- Matt Porter no longer works as a maintainer on Broadcom SoCs
Build-time issues
- A compile-time error for at91
- Several minor DT fixes on at91, imx, exynos, socfpga, and omap
- The new digicolor platform was not correctly enabled at all
Configuration issues
- Two defconfig fix for regressions using USB on versatile express
and on OMAP3
- Enabling all 8 CPUs on Allwinner/SUNxi
- Enabling the new STiH410 platform to be usable
Bug fixes in platform code
- A missing barrier for socfpga
- Fixing LPDDR1 self-refresh mode on at91
- Fixing RTC interrupt numbers on Exynos3250
- Fixing a cache-coherency issues in CPU power-down on Exynos5
- Multiple small OMAP power management fixes"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (69 commits)
MAINTAINERS: Add myself as co-maintainer to the legacy support of the mvebu SoCs
ARM: at91: pm_slowclock: fix the compilation error
ARM: at91/dt: fix USB high-speed clock to select UTMI
ARM: at91/dt: fix at91 udc compatible strings
ARM: at91/dt: declare matrix node as a syscon device
ARM: vexpress: update CONFIG_USB_ISP1760 option
ARM: digicolor: add the machine directory to Makefile
ARM: STi: Add STiH410 SoC support
MAINTAINERS: add Freescale Vybrid SoC
MAINTAINERS: Remove self as ARM mach-bcm co-maintainer
ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: OMAP5: fix polling intervals for thermal zones
...
Linus Torvalds [Sun, 15 Mar 2015 17:41:30 +0000 (10:41 -0700)]
Merge tag 'irqchip-fixes-4.0' of git://git.infradead.org/users/jcooper/linux
Pull irqchip fixes from Jason Cooper:
"armada-370-xp:
- Chained per-cpu interrupts
gic{,-v3,v3-its}"
- Various fixes for safer operation"
* tag 'irqchip-fixes-4.0' of git://git.infradead.org/users/jcooper/linux:
irqchip: gicv3-its: Support safe initialization
irqchip: gicv3-its: Define macros for GITS_CTLR fields
irqchip: gicv3-its: Add limitation to page order
irqchip: gicv3-its: Use 64KB page as default granule
irqchip: gicv3-its: Zero itt before handling to hardware
irqchip: gic-v3: Fix out of bounds access to cpu_logical_map
irqchip: gic: Fix unsafe locking reported by lockdep
irqchip: gicv3-its: Fix unsafe locking reported by lockdep
irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration
irqchip: gicv3-its: Allocate enough memory for the full range of DeviceID
irqchip: gicv3-its: Fix ITS CPU init
irqchip: armada-370-xp: Fix chained per-cpu interrupts
Forest Wilkinson [Fri, 13 Mar 2015 06:58:16 +0000 (23:58 -0700)]
HID: tivo: enable all buttons on the TiVo Slide Pro remote
The linux kernel has supported the TiVo Slide remote control for some time, but
does not recognize the USB ID of the newer Slide Pro. This patch adds the
missing data structures so the newer remote will be recognized by the driver,
thereby allowing the TiVo, LiveTV, and Thumbs Up/Down buttons to be
mapped with a hwdb file.
Li Jun [Sun, 8 Mar 2015 08:05:01 +0000 (16:05 +0800)]
usb: chipidea: otg: add a_alt_hnp_support response for B device
This patch adds response to a_alt_hnp_support set feature request from legacy
A device, that is, B-device can provide a message to the user indicating that
the user needs to connect the B-device to an alternate port on the A-device.
A device sets this feature indicates to the B-device that it is connected
to an A-device port that is not capable of HNP, but that the A-device does have
an alternate port that is capable of HNP.
[Peter]
Without this patch, the OTG B device can't be enumerated on
non-HNP port at A device, see below log:
[ 2.287464] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.293105] usb 1-1: can't set HNP mode: -32
[ 2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc
[ 2.460635] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.466424] usb 1-1: can't set HNP mode: -32
[ 2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc
[ 2.630649] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.636436] usb 1-1: can't set HNP mode: -32
[ 2.641003] usb usb1-port1: unable to enumerate USB device
Merge tag 'for-4.0-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
contains fixes all over drivers/phy and includes the following
*) Using phy_get_drvdata instead of dev_get_drvdata in armada375-usb2.c
*) Fixes w.r.t checking return values in regmap APIs, protecting regmap ops
with spin lock and directly using regmap_update_bits instead of having a
separate function to do the same in the various PHYs used in exynos.
*) check return value in platform_get_resource of hix5hd2-sata PHY
*) Removed NULL terminating entry from phys array and fix off-by-one
valid value checking for args->args[0] in of_xlate of exynos USB PHY.
*) Fixup rockchip_usb_phy_power_on failure path
*) Fix devm_phy_match to find the correct match in phy core and also fix to
return the correct value from PHY APIs if PM runtime is not enabled.
*) Removed redundant code in twl4030 and xgene
*) Fixed sizeof during memory allocation in miphy PHYs
*) simplify ti_pipe3_dpll_wait_lock implementation, fix missing clk_prepare
when using old dt name and nit pick in MOUDLE_ALIAS in TI PHYs.
Linus Torvalds [Sat, 14 Mar 2015 21:54:25 +0000 (14:54 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Misc i915, vmwgfx and radeon fixes along with a fix for one of those
recursive sleep mutex debug cases in the mst code"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix an issue with the device losing its irq line on module unload
drm/vmwgfx: Correctly NULLify dma buffer pointer on failure
drm/vmwgfx: Reorder device takedown somewhat
drm/vmwgfx: Fix a couple of lock dependency violations
drm/radeon: drop setting UPLL to sleep mode
drm/radeon: fix wait to actually occur after the signaling callback
drm/i915: Prevent TLB error on first execution on SNB
drm/i915: Do both mt and gen6 style forcewake reset on ivb probe
drm/i915: Make WAIT_IOCTL negative timeouts be indefinite again
drm/i915: use in_interrupt() not in_irq() to check context
drm/mst: fix recursive sleep warning on qlock
drm: Don't assign fbs for universal cursor support to files
Linus Torvalds [Sat, 14 Mar 2015 21:23:50 +0000 (14:23 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"This is a simple fix for a domain revalidation crash which has
recently turned up in the libsas code (applies to mvsas, isc and
aic94xx)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
libsas: Fix Kernel Crash in smp_execute_task
David S. Miller [Sat, 14 Mar 2015 18:35:26 +0000 (14:35 -0400)]
Merge tag 'linux-can-fixes-for-4.0-20150314' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
Hello David, this is a pull request for net/master, consisting of two patches:
In the first patch Michal Simek enables the xilinx CAN driver for ARM64. The
second patch by Ahmed S. Darwish fixes a race condition in the tx-queue of the
kvaser_usb driver.
====================
Linus Torvalds [Sat, 14 Mar 2015 16:32:00 +0000 (09:32 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- add TLB invalidation for page table tear-down which was missed when
support for CONFIG_HAVE_RCU_TABLE_FREE was added (assuming page table
freeing was always deferred)
- use UEFI for system and reset poweroff if available
- fix asm label placement in relation to the alignment statement
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: put __boot_cpu_mode label after alignment instead of before
efi/arm64: use UEFI for system reset and poweroff
arm64: Invalidate the TLB corresponding to intermediate page table levels
Linus Torvalds [Sat, 14 Mar 2015 16:26:23 +0000 (09:26 -0700)]
Merge tag 'linux-kselftest-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fix from Shuah Khan:
"selftests/exec: Check if the syscall exists and bail if not"
* tag 'linux-kselftest-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/exec: Check if the syscall exists and bail if not
Christoffer Dall [Fri, 13 Mar 2015 17:02:56 +0000 (17:02 +0000)]
arm/arm64: KVM: Keep elrsr/aisr in sync with software model
There is an interesting bug in the vgic code, which manifests itself
when the KVM run loop has a signal pending or needs a vmid generation
rollover after having disabled interrupts but before actually switching
to the guest.
In this case, we flush the vgic as usual, but we sync back the vgic
state and exit to userspace before entering the guest. The consequence
is that we will be syncing the list registers back to the software model
using the GICH_ELRSR and GICH_EISR from the last execution of the guest,
potentially overwriting a list register containing an interrupt.
This showed up during migration testing where we would capture a state
where the VM has masked the arch timer but there were no interrupts,
resulting in a hung test.
Catalin Marinas [Wed, 11 Mar 2015 12:20:39 +0000 (12:20 +0000)]
arm64: Invalidate the TLB corresponding to intermediate page table levels
The ARM architecture allows the caching of intermediate page table
levels and page table freeing requires a sequence like:
pmd_clear()
TLB invalidation
pte page freeing
With commit 5e5f6dc10546 (arm64: mm: enable HAVE_RCU_TABLE_FREE logic),
the page table freeing batching was moved from tlb_remove_page() to
tlb_remove_table(). The former takes care of TLB invalidation as this is
also shared with pte clearing and page cache page freeing. The latter,
however, does not invalidate the TLBs for intermediate page table levels
as it probably relies on the architecture code to do it if required.
When the mm->mm_users < 2, tlb_remove_table() does not do any batching
and page table pages are freed before tlb_finish_mmu() which performs
the actual TLB invalidation.
This patch introduces __tlb_flush_pgtable() for arm64 and calls it from
the {pte,pmd,pud}_free_tlb() directly without relying on deferred page
table freeing.
Merge tag 'fixes-for-v4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.0-rc3
Revert interrupt endpoint support from g_zero as it regresses
musb.
A possible deadlock in isp1760 udc irq has been fixed.
A fix to dwc2 for disconnect IRQ handling.
We also have a new device ID for isp1760.
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Jacob Pan [Fri, 13 Mar 2015 10:48:56 +0000 (03:48 -0700)]
powercap / RAPL: handle domains with different energy units
The current driver assumes all RAPL domains within a CPU package
have the same energy unit. This is no longer true for HSW server
CPUs since DRAM domain has is own fixed energy unit which can be
different than the package energy unit enumerated by package
power MSR. In fact, the default HSW EP package power unit is 61uJ
whereas DRAM domain unit is 15.3uJ. The result is that DRAM power
consumption is counted 4x more than real power reported by energy
counters, similarly for max_energy_range_uj of DRAM domain.
This patch adds domain specific energy unit per cpu type, it allows
domain energy unit to override package energy unit if non zero.
Please see this document for details.
"Intel Xeon Processor E5-1600 and E5-2600 v3 Product Families, Volume 2 of 2.
Datasheet, September 2014, Reference Number: 330784-001 "
Linus Torvalds [Fri, 13 Mar 2015 21:30:38 +0000 (14:30 -0700)]
Merge tag 'pm+acpi-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Just two fixes, one for an ACPI LPSS driver issue introduced during
the 3.17 cycle and one revert of a recent commit that sort of broke
the cpupower tool.
Specifics:
- Fix an ACPI LPSS (Low-Power Subsystem) driver issue causing the
8250_dw driver to confuse an LPSS clock with another one it is
supposed to handle due to the lack of identification allowing it to
tell those clocks apart (Heikki Krogerus).
- Revert a recent commit that was supposed to improve the usability
of the cpupower tool, but clearly did the opposite (Josh Boyer)"
* tag 'pm+acpi-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "cpupower Makefile change to help run the tool without 'make install'"
ACPI / LPSS: provide con_id for the clkdev
Merge branch 'cpuidle/4.0-fixes' of http://git.linaro.org/people/daniel.lezcano/linux into pm-cpuidle
Pull ARM cpuidle fixes for v4.0 from Daniel Lezcano.
* 'cpuidle/4.0-fixes' of http://git.linaro.org/people/daniel.lezcano/linux:
cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
cpuidle: mvebu: Fix the CPU PM notifier usage
Dave could hit this assert consistently running btrfs/078. This is because
when we update the block groups we could truncate the free space, which would
try to delete the csums for that range and dirty the csum root. For this to
happen we have to have already written out the csum root so it's kind of hard to
hit this case. This patch fixes this by changing the logic to only write the
dirty block groups if the dirty_cowonly_roots list is empty. This will get us
the same effect as before since we add the extent root last, and will cover the
case that we dirty some other root again but not the extent root. Thanks,
Josef Bacik [Fri, 13 Mar 2015 19:12:23 +0000 (15:12 -0400)]
Btrfs: account for the correct number of extents for delalloc reservations
Direct IO can easily pass in an buffer that is greater than
BTRFS_MAX_EXTENT_SIZE, so take this into account when reserving extents in the
delalloc reservation code. Thanks,
Josef Bacik [Fri, 13 Mar 2015 19:12:08 +0000 (15:12 -0400)]
Btrfs: fix merge delalloc logic
My patch to properly count outstanding extents wrt MAX_EXTENT_SIZE introduced a
regression when re-dirtying already dirty areas. We have logic in split to make
sure we are taking the largest space into account but didn't have it for merge,
so it was sometimes making us think we were turning a tiny extent into a huge
extent, when in reality we already had a huge extent and needed to use the other
side in our logic. This fixes the regression that was reported by a user on
list. Thanks,
Liu Bo [Fri, 6 Mar 2015 12:23:44 +0000 (20:23 +0800)]
Btrfs: catch transaction abortion after waiting for it
This problem is uncovered by a test case: http://patchwork.ozlabs.org/patch/244297.
Fsync() can report success when it actually doesn't. When we
have several threads running fsync() at the same tiem and in one fsync() we
get a transaction abortion due to some problems(in the test case it's disk
failures), and other fsync()s may return successfully which makes userspace
programs think that data is now safely flushed into disk.
It's because that after fsyncs() fail btrfs_sync_log() due to disk failures,
they get to try btrfs_commit_transaction() where it finds that there is
already a transaction being committed, and they'll just call wait_for_commit()
and return. Note that we actually check "trans->aborted" in btrfs_end_transaction,
but it's likely that the error message is still not yet throwed out and only after
wait_for_commit() we're sure whether the transaction is committed successfully.
This add the necessary check and it now passes the test.
Fabian Frederick [Sat, 14 Feb 2015 12:10:22 +0000 (13:10 +0100)]
btrfs: fix sizeof format specifier in btrfs_check_super_valid()
This patch fixes mips compilation warning:
fs/btrfs/disk-io.c: In function 'btrfs_check_super_valid':
fs/btrfs/disk-io.c:3927:21: warning: format '%lu' expects argument
of type 'long unsigned int', but argument 3 has type 'unsigned int' [-Wformat]
Linus Torvalds [Fri, 13 Mar 2015 20:34:38 +0000 (13:34 -0700)]
Merge tag 'stable/for-linus-4.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- fix a PV regression in 3.19.
- fix a dom0 crash on hosts with large numbers of PIRQs.
- prevent pcifront from disabling memory or I/O port access, which may
trigger host crashes.
* tag 'stable/for-linus-4.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-pciback: limit guest control of command register
xen/events: avoid NULL pointer dereference in dom0 on large machines
xen: Remove trailing semicolon from xenbus_register_frontend() definition
x86/xen: correct bug in p2m list initialization
Linus Torvalds [Fri, 13 Mar 2015 20:30:00 +0000 (13:30 -0700)]
Merge tag 'sound-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This is a round of HD-audio fixes: there are a long-standing
regression fix and a few more device/codec-specific quirks.
In addition, a couple of FireWire regression fixes, a USB-audio quirk
for Roland UA-22 and a sanity check in API for user-defined control
elements"
* tag 'sound-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't access stereo amps for mono channel widgets
ALSA: hda - Add workaround for MacBook Air 5,2 built-in mic
ALSA: hda - Set single_adc_amp flag for CS420x codecs
ALSA: snd-usb: add quirks for Roland UA-22
ALSA: control: Add sanity checks for user ctl id name string
ALSA: hda - Fix built-in mic on Compaq Presario CQ60
ALSA: firewire-lib: leave unit reference counting completely
Revert "ALSA: dice: fix wrong offsets for Dice interface"
ALSA: hda - Fix regression of HD-audio controller fallback modes
Linus Torvalds [Fri, 13 Mar 2015 18:10:10 +0000 (11:10 -0700)]
Merge tag 'devicetree-fixes-for-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix for stdout-path option parsing with added unittest
- fix for stdout-path interaction with earlycon
- several DT unittest fixes
- fix Sparc allmodconfig build error on of_platform_register_reconfig_notifier
- several DT overlay kconfig and build warning fixes
- several DT binding documentation updates
* tag 'devicetree-fixes-for-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/platform: Fix sparc:allmodconfig build
of: unittest: Add options string testcase variants
of: fix handling of '/' in options for of_find_node_by_path()
of/unittest: Fix the wrong expected value in of_selftest_property_string
of/unittest: remove the duplicate of_changeset_init
dt: submitting-patches: clarify that DT maintainers are to be cced on bindings
of: unittest: fix I2C dependency
of/overlay: Remove unused variable
Documentation: DT: Renamed of-serial.txt to 8250.txt
of: Fix premature bootconsole disable with 'stdout-path'
serial: add device tree binding documentation for ETRAX FS UART
of/overlay: Directly include idr.h
of: Drop superfluous dependance for OF_OVERLAY
of: Add vendor prefix for Arasan
of: Add prompt for OF_OVERLAY config
projects / linux.git / log