Heiko Carstens [Thu, 16 Dec 2021 12:27:10 +0000 (13:27 +0100)]
s390/crash_dump: fix virtual vs physical address handling
Signal processor STORE STATUS requires a physical address where register
contents are supposed to be written to, however the kernel must read the
data via the corresponding virtual address.
Also the allocated save_area, where register contents are copied to,
resides in virtual address space.
Fix this by using proper __pa() conversion, or correct memblock_alloc()
invocation.
Heiko Carstens [Thu, 16 Dec 2021 18:28:20 +0000 (19:28 +0100)]
s390/crypto: fix compile error for ChaCha20 module
The clgfi instruction used within the ChaCha20 assembly is only
available for z9-109 and newer machines, and therefore this will
generate a compile error if compiled e.g. with MARCH_Z900.
Given that the assembler code will only be executed on machines with
vector instructions, which became much later available than z9-109,
use insn notation to generate the clgfi instruction, and avoid compile
errors due to unknown instructions.
Fixes: b087dfab4d39 ("s390/crypto: add SIMD implementation for ChaCha20") Reported-by: kernel test robot <[email protected]> Reviewed-by: Harald Freudenberger <[email protected]> Signed-off-by: Heiko Carstens <[email protected]>
When CONFIG_DEBUG_VM is defined check that pending remove
and tracking nibbles (bits 31-24 of the page refcount) are
cleared. Should the earlier stages of the page lifespan
have a race or logical error, such check could help in
exposing the issue.
Explicitly encode immediate value of pending remove nibble
(bits 31-28) and tracking nibble (bits 27-24) of the page
refcount whenever these nibbles are tested or changed, for
better readability. Also, add some comments describing how
the fragments are handled.
There is a race on concurrent 2KB-pgtables release paths when
both upper and lower halves of the containing parent page are
freed, one via page_table_free_rcu() + __tlb_remove_table(),
and the other via page_table_free(). The race might lead to a
corruption as result of remove of list item in page_table_free()
concurrently with __free_page() in __tlb_remove_table().
Let's assume first the lower and next the upper 2KB-pgtables are
freed from a page. Since both halves of the page are allocated
the tracking byte (bits 24-31 of the page _refcount) has value
of 0x03 initially:
The problem is page_table_free() releases the page as result of
lower nibble unset and __tlb_remove_table() observing zero too
early. With this update page_table_free() will use the similar
logic as page_table_free_rcu() + __tlb_remove_table(), and mark
the fragment as pending for removal in the upper nibble until
after the list_del().
In other words, the parent page is considered as unreferenced and
safe to release only when the lower nibble is cleared already and
unsetting a bit in upper nibble results in that nibble turned zero.
s390/sclp: release SCLP early buffer after kernel initialization
The SCLP early buffer is used only during kernel initialization and can be
freed afterwards. The only way to ensure that it is not released while
being in use, is to release it in free_initmem().
s390/nmi: disable interrupts on extended save area update
Updating of the pointer to machine check extended save area
on the IPL CPU needs the lowcore protection to be disabled.
Disable interrupts while the protection is off to avoid
unnoticed writes to the lowcore.
Juergen Christ [Mon, 22 Nov 2021 13:01:34 +0000 (14:01 +0100)]
s390/zcrypt: CCA control CPRB sending
When sending a CCA CPRB to a control domain, the CPRB has to be sent via a
usage domain. Previous code used the default domain to route this message.
If the default domain is not online and ready to send the CPRB, the ioctl will
fail even if other usage domains could be used to send the CPRB.
To improve this, instead of using the default domain, switch to auto-select of
the domain.
Heiko Carstens [Mon, 13 Dec 2021 18:16:38 +0000 (19:16 +0100)]
s390/uv: fix memblock virtual vs physical address confusion
memblock_alloc_try_nid() returns a virtual address, however in error
case the allocated memory is incorrectly freed with memblock_phys_free().
Properly use memblock_free() instead, and pass a physical address to
uv_init() to fix this.
Note: this doesn't fix a bug currently, since virtual and physical
addresses are identical.
s390/exit: remove dead reference to do_exit from copy_thread
My s390 assembly is not particularly good so I have read the history
of the reference to do_exit copy_thread and have been able to
verify that do_exit is not used.
The general argument is that s390 has been changed to use the generic
kernel_thread and kernel_execve and the generic versions do not call
do_exit. So it is strange to see a do_exit reference sitting there.
The history of the do_exit reference in s390's version of copy_thread
seems conclusive that the do_exit reference is something that lingers
and should have been removed several years ago.
Up through 8d19f15a60be ("[PATCH] s390 update (1/27): arch.") the
s390 code made a call to the exit(2) system call when a kernel thread
finished. Then kernel_thread_starter was added which branched
directly to the value in register 11 when the kernel thread finshed.
The value in register 11 was set in kernel_thread to
"regs.gprs[11] = (unsigned long) do_exit"
In commit 37fe5d41f640 ("s390: fold kernel_thread_helper() into
ret_from_fork()") kernel_thread_starter was moved into entry.S and
entry64.S unchanged (except for the syntax differences between inline
assemly and in the assembly file).
In commit f9a7e025dfc2 ("s390: switch to generic kernel_thread()") the
assignment to "gprs[11]" was moved into copy_thread from the old
kernel_thread. The helper kernel_thread_starter was still being used
and was still branching to "%r11" at the end.
In commit 30dcb0996e40 ("s390: switch to saner kernel_execve()
semantics") kernel_thread_starter was changed to unconditionally
branch to sysc_tracenogo instead to %r11 which held the value of
do_exit. Unfortunately copy_thread was not updated to stop passing
do_exit in "gprs[11]".
In commit 56e62a737028 ("s390: convert to generic entry")
kernel_thread_starter was replaced by __ret_from_fork. And the code
still continued to pass do_exit in "gprs[11]" despite __ret_from_fork
not caring in the slightest.
Remove this dead reference to do_exit to make it clear that s390 is
not doing anything with do_exit in copy_thread.
History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
The address of the notification-indicator byte is an absolute
address. Therefore convert its virtual to a physical address before
being used with PQAP(AQIC).
Note: this currently doesn't fix a real bug, since virtual addresses
are indentical to physical ones.
Heiko Carstens [Thu, 9 Dec 2021 11:01:25 +0000 (12:01 +0100)]
s390/pgalloc: use pointers instead of unsigned long values
After adding the missing __va()/__pa() calls to the base asce
functions there are even more casts in the code than before. Make the
code more readable by passing and using pointers to page tables,
instead of using unsigned values for the same purpose.
This allows to get rid of nearly all casts within the code.
Heiko Carstens [Tue, 7 Dec 2021 19:06:21 +0000 (20:06 +0100)]
s390/pgalloc: add virt/phys address handling to base asce functions
The base asce functions create/free page tables open-coded to make
sure that the returned asce and page tables do not make use of any
enhanced DAT features like e.g. large pages. This is required for some
I/O functions that use an asce, like e.g. some service call requests.
Handling of virtual vs physical addresses is missing; therefore add
that now.
Note: this currently doesn't fix a real bug, since virtual addresses
are indentical to physical ones.
Heiko Carstens [Tue, 7 Dec 2021 18:24:00 +0000 (19:24 +0100)]
s390/cmm: add missing virt_to_phys() conversion
diag10_range() expects a pfn, however the current cmm code is shifting
a virtual address, instead of a physical address by PAGE_SHIFT bits,
which would give a wrong result in case if V!=R.
Use virt_to_pfn() to fix this.
Note: this currently doesn't fix a real bug, since virtual addresses
are indentical to physical ones.
Heiko Carstens [Mon, 6 Dec 2021 17:55:21 +0000 (18:55 +0100)]
s390/mm: add missing phys_to_virt translation to page table dumper
The page table dumper walks page table tables without using standard
page table primitives in order to also dump broken entries. However it
currently does not translate physical to virtual addresses before
dereferencing them. Therefore add this missing translation.
Tony Krowiak [Wed, 27 Oct 2021 15:20:14 +0000 (11:20 -0400)]
s390/vfio-ap: add status attribute to AP queue device's sysfs dir
This patch adds a sysfs 'status' attribute to a queue device when it is
bound to the vfio_ap device driver. The field displays a string indicating
the status of the queue device:
Status String: Indicates:
------------- ---------
"assigned" the queue is assigned to an mdev, but is not in use by a
KVM guest.
"in use" the queue is assigned to an mdev and is in use by a KVM
guest.
"unassigned" the queue is not assigned to an mdev.
The status string will be displayed by the 'lszcrypt' command if the queue
device is bound to the vfio_ap device driver.
Julian Wiedmann [Wed, 24 Nov 2021 09:16:53 +0000 (10:16 +0100)]
s390/qdio: remove unneeded sanity check in qdio_do_sqbs()
All callers of set_buf_states() are already making sure that 'count'
is not 0. So don't check it an additional time.
Note that our own code also doesn't _require_ the count to be sane
(ie. we can't overrun an array or similar). So worst case HW would
simply reject the SQBS operation and report an error.
Niklas Schnelle [Thu, 25 Nov 2021 15:46:00 +0000 (16:46 +0100)]
s390/pci: use physical addresses in DMA tables
The entries in the DMA translation tables for our IOMMU must specify
physical addresses of either the next level table or the final page
to be mapped for DMA. Currently however the code simply passes the
virtual addresses of both. On the other hand we still need to walk the
tables via their virtual addresses so we need to do a phys_to_virt()
when setting the entries and a virt_to_phys() when getting them.
Similarly when passing the I/O translation anchor to the hardware we
must also specify its physical address.
As the DMA and IOMMU APIs we are implementing already use the correct
phys_addr_t type for the address to be mapped let's also thread this
through instead of treating it as just an unsigned long.
Note: this currently doesn't fix a real bug, since virtual addresses
are indentical to physical ones.
Niklas Schnelle [Thu, 25 Nov 2021 15:42:22 +0000 (16:42 +0100)]
s390/pci: use phys_to_virt() for AIBVs/DIBVs
The adapter and directed interrupt bit vectors need to be referenced in
the FIB with their physical not their virtual address. So use
virt_to_phys() as approrpiate.
Note: this currently doesn't fix a real bug, since virtual addresses
are indentical to physical ones.
Julian Wiedmann [Mon, 30 Aug 2021 12:28:36 +0000 (15:28 +0300)]
s390/qdio: split do_QDIO()
The callers know what type of queue they want to work with. Introduce
type-specific variants to add buffers on an {Input,Output} queue, so
that we can avoid some function parameters and the de-muxing into
type-specific hot paths.
The callers know what type of queue they want to inspect. Introduce
type-specific variants to inspect an {Input,Output} queue, so that we
can avoid one function parameter and some conditional branches in the
hot paths.
Julian Wiedmann [Mon, 15 Nov 2021 07:28:08 +0000 (08:28 +0100)]
s390/qdio: clarify handler logic for qdio_handle_activate_check()
qdio_handle_activate_check() tries to re-use one of the queue-specific
handlers to report that the ACTIVATE ccw has been terminated. But the
logic to select that handler is overly complex - in practice both
qdio drivers have at least one Input Queue, so we never take the other
paths.
Make things more obvious by removing this unused code, and clearly
spelling out that we re-use the Input Handler for generic error
reporting. This also paves the way for a world without queue-specific
error handlers.
Julian Wiedmann [Mon, 15 Nov 2021 07:21:38 +0000 (08:21 +0100)]
s390/qdio: clean up access to queue in qdio_handle_activate_check()
qdio_handle_activate_check() re-uses a queue-specific handler to report
that the ACTIVATE ccw has been terminated. It uses either the first
input or output queue, so we can hard-code q->nr as 0. Also don't
access the q->irq_ptr parent pointer, we already have a pointer to
the qdio_irq.
Julian Wiedmann [Tue, 24 Aug 2021 06:37:06 +0000 (09:37 +0300)]
s390/qdio: avoid allocating the qdio_irq with GFP_DMA
The qdio_irq contains only two fields that are directly exposed to the
HW (ccw and qib). And only the ccw needs to reside in 31-bit memory. So
allocate it separately, and remove the GFP_DMA constraint from the
qdio_irq allocation.
Fetch the individual CIWs when we actually need them, rather than
fetching both of them in qdio_setup_irq() and then needing to cache
them inside the qdio_irq.
Also deal with the error when a CIW is not available, instead of
silently dropping this error condition in qdio_setup_irq()'s caller.
Vineeth Vijayan [Tue, 29 Jun 2021 07:38:22 +0000 (09:38 +0200)]
s390/cio: remove uevent suppress from cio driver
commit fa1a8c23eb7d ("s390: cio: Delay uevents for subchannels")
introduced suppression of uevents for a subchannel until after it is
clear that the subchannel would not be unregistered again
immediately. This was done to avoid uevents being generated for I/O
subchannels with no valid device, which can happen on LPAR.
However, this also has some drawbacks: All subchannel drivers need to
manually remove the uevent suppression and generate an ADD uevent as
soon as they are sure that the subchannel will stay around. This misses
out on all uevents that are not the initial ADD uevent that would be
generated while uevents are suppressed; for example, all subchannels
were missing the BIND uevent.
As uevents being generated even for I/O subchannels without an
operational device turned out to be not as bad as missing uevents and
complicating the code flow, let's remove uevent suppression for
subchannels.
Linus Torvalds [Sun, 5 Dec 2021 20:58:18 +0000 (12:58 -0800)]
Merge tag 'for-5.16/parisc-6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Some bug and warning fixes:
- Fix "make install" to use debians "installkernel" script which is
now in /usr/sbin
- Fix the bindeb-pkg make target by giving the correct KBUILD_IMAGE
file name
- Fix compiler warnings by annotating parisc agp init functions with
__init
- Fix timekeeping on SMP machines with dual-core CPUs
- Enable some more config options in the 64-bit defconfig"
* tag 'for-5.16/parisc-6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Mark cr16 CPU clocksource unstable on all SMP machines
parisc: Fix "make install" on newer debian releases
parisc/agp: Annotate parisc agp init functions with __init
parisc: Enable sata sil, audit and usb support on 64-bit defconfig
parisc: Fix KBUILD_IMAGE for self-extracting kernel
Linus Torvalds [Sun, 5 Dec 2021 17:34:57 +0000 (09:34 -0800)]
Merge tag 'usb-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for a few reported issues. Included in
here are:
- xhci fix for a _much_ reported regression. I don't think there's a
community distro that has not reported this problem yet :(
- new USB quirk addition
- cdns3 minor fixes
- typec regression fix.
All of these have been in linux-next with no reported problems, and
the xhci fix has been reported by many to resolve their reported
problem"
* tag 'usb-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdnsp: Fix a NULL pointer dereference in cdnsp_endpoint_init()
usb: cdns3: gadget: fix new urb never complete if ep cancel previous requests
usb: typec: tcpm: Wait in SNK_DEBOUNCED until disconnect
USB: NO_LPM quirk Lenovo Powered USB-C Travel Hub
xhci: Fix commad ring abort, write all 64 bits to CRCR register.
Linus Torvalds [Sun, 5 Dec 2021 17:13:20 +0000 (09:13 -0800)]
Merge tag 'tty-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small TTY and Serial driver fixes for 5.16-rc4 to
resolve a number of reported problems.
They include:
- liteuart serial driver fixes
- 8250_pci serial driver fixes for pericom devices
- 8250 RTS line control fix while in RS-485 mode
- tegra serial driver fix
- msm_serial driver fix
- pl011 serial driver new id
- fsl_lpuart revert of broken change
- 8250_bcm7271 serial driver fix
- MAINTAINERS file update for rpmsg tty driver that came in 5.16-rc1
- vgacon fix for reported problem
All of these, except for the 8250_bcm7271 fix have been in linux-next
with no reported problem. The 8250_bcm7271 fix was added to the tree
on Friday so no chance to be linux-next yet. But it should be fine as
the affected developers submitted it"
* tag 'tty-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_bcm7271: UART errors after resuming from S2
serial: 8250_pci: rewrite pericom_do_set_divisor()
serial: 8250_pci: Fix ACCES entries in pci_serial_quirks array
serial: 8250: Fix RTS modem control while in rs485 mode
Revert "tty: serial: fsl_lpuart: drop earlycon entry for i.MX8QXP"
serial: tegra: Change lower tolerance baud rate limit for tegra20 and tegra30
serial: liteuart: relax compile-test dependencies
serial: liteuart: fix minor-number leak on probe errors
serial: liteuart: fix use-after-free and memleak on unbind
serial: liteuart: Fix NULL pointer dereference in ->remove()
vgacon: Propagate console boot parameters before calling `vc_resize'
tty: serial: msm_serial: Deactivate RX DMA for polling support
serial: pl011: Add ACPI SBSA UART match id
serial: core: fix transmit-buffer reset and memleak
MAINTAINERS: Add rpmsg tty driver maintainer
Linus Torvalds [Sun, 5 Dec 2021 16:58:52 +0000 (08:58 -0800)]
Merge tag 'timers_urgent_for_v5.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Borislav Petkov:
- Prevent a tick storm when a dedicated timekeeper CPU in nohz_full
mode runs for prolonged periods with interrupts disabled and ends up
programming the next tick in the past, leading to that storm
* tag 'timers_urgent_for_v5.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers/nohz: Last resort update jiffies on nohz_full IRQ entry
Linus Torvalds [Sun, 5 Dec 2021 16:53:31 +0000 (08:53 -0800)]
Merge tag 'sched_urgent_for_v5.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Properly init uclamp_flags of a runqueue, on first enqueuing
- Fix preempt= callback return values
- Correct utime/stime resource usage reporting on nohz_full to return
the proper times instead of shorter ones
* tag 'sched_urgent_for_v5.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/uclamp: Fix rq->uclamp_max not set on first enqueue
preempt/dynamic: Fix setup_preempt_mode() return value
sched/cputime: Fix getrusage(RUSAGE_THREAD) with nohz_full
Linus Torvalds [Sun, 5 Dec 2021 16:43:35 +0000 (08:43 -0800)]
Merge tag 'x86_urgent_for_v5.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix a couple of SWAPGS fencing issues in the x86 entry code
- Use the proper operand types in __{get,put}_user() to prevent
truncation in SEV-ES string io
- Make sure the kernel mappings are present in trampoline_pgd in order
to prevent any potential accesses to unmapped memory after switching
to it
- Fix a trivial list corruption in objtool's pv_ops validation
- Disable the clocksource watchdog for TSC on platforms which claim
that the TSC is constant, doesn't stop in sleep states, CPU has TSC
adjust and the number of sockets of the platform are max 2, to
prevent erroneous markings of the TSC as unstable.
- Make sure TSC adjust is always checked not only when going idle
- Prevent a stack leak by initializing struct _fpx_sw_bytes properly in
the FPU code
- Fix INTEL_FAM6_RAPTORLAKE define naming to adhere to the convention
* tag 'x86_urgent_for_v5.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen: Add xenpv_restore_regs_and_return_to_usermode()
x86/entry: Use the correct fence macro after swapgs in kernel CR3
x86/entry: Add a fence for kernel entry SWAPGS in paranoid_entry()
x86/sev: Fix SEV-ES INS/OUTS instructions for word, dword, and qword
x86/64/mm: Map all kernel memory into trampoline_pgd
objtool: Fix pv_ops noinstr validation
x86/tsc: Disable clocksource watchdog for TSC on qualified platorms
x86/tsc: Add a timer to make sure TSC_adjust is always checked
x86/fpu/signal: Initialize sw_bytes in save_xstate_epilog()
x86/cpu: Drop spurious underscore from RAPTOR_LAKE #define
Linus Torvalds [Sun, 5 Dec 2021 16:25:33 +0000 (08:25 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more kvm fixes from Paolo Bonzini:
- Static analysis fix
- New SEV-ES protocol for communicating invalid VMGEXIT requests
- Ensure APICv is considered inactive if there is no APIC
- Fix reserved bits for AMD PerfEvtSeln register
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Do not terminate SEV-ES guests on GHCB validation failure
KVM: SEV: Fall back to vmalloc for SEV-ES scratch area if necessary
KVM: SEV: Return appropriate error codes if SEV-ES scratch setup fails
KVM: x86/mmu: Retry page fault if root is invalidated by memslot update
KVM: VMX: Set failure code in prepare_vmcs02()
KVM: ensure APICv is considered inactive if there is no APIC
KVM: x86/pmu: Fix reserved bits for AMD PerfEvtSeln register
Tom Lendacky [Thu, 2 Dec 2021 18:52:05 +0000 (12:52 -0600)]
KVM: SVM: Do not terminate SEV-ES guests on GHCB validation failure
Currently, an SEV-ES guest is terminated if the validation of the VMGEXIT
exit code or exit parameters fails.
The VMGEXIT instruction can be issued from userspace, even though
userspace (likely) can't update the GHCB. To prevent userspace from being
able to kill the guest, return an error through the GHCB when validation
fails rather than terminating the guest. For cases where the GHCB can't be
updated (e.g. the GHCB can't be mapped, etc.), just return back to the
guest.
The new error codes are documented in the lasest update to the GHCB
specification.
KVM: SEV: Fall back to vmalloc for SEV-ES scratch area if necessary
Use kvzalloc() to allocate KVM's buffer for SEV-ES's GHCB scratch area so
that KVM falls back to __vmalloc() if physically contiguous memory isn't
available. The buffer is purely a KVM software construct, i.e. there's
no need for it to be physically contiguous.
Return appropriate error codes if setting up the GHCB scratch area for an
SEV-ES guest fails. In particular, returning -EINVAL instead of -ENOMEM
when allocating the kernel buffer could be confusing as userspace would
likely suspect a guest issue.
Linus Torvalds [Sat, 4 Dec 2021 21:43:52 +0000 (13:43 -0800)]
Merge tag '5.16-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Three SMB3 multichannel/fscache fixes and a DFS fix.
In testing multichannel reconnect scenarios recently various problems
with the cifs.ko implementation of fscache were found (e.g. incorrect
initialization of fscache cookies in some cases)"
* tag '5.16-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: avoid use of dstaddr as key for fscache client cookie
cifs: add server conn_id to fscache client cookie
cifs: wait for tcon resource_id before getting fscache super
cifs: fix missed refcounting of ipc tcon
Helge Deller [Sat, 4 Dec 2021 20:21:46 +0000 (21:21 +0100)]
parisc: Mark cr16 CPU clocksource unstable on all SMP machines
In commit c8c3735997a3 ("parisc: Enhance detection of synchronous cr16
clocksources") I assumed that CPUs on the same physical core are syncronous.
While booting up the kernel on two different C8000 machines, one with a
dual-core PA8800 and one with a dual-core PA8900 CPU, this turned out to be
wrong. The symptom was that I saw a jump in the internal clocks printed to the
syslog and strange overall behaviour. On machines which have 4 cores (2
dual-cores) the problem isn't visible, because the current logic already marked
the cr16 clocksource unstable in this case.
This patch now marks the cr16 interval timers unstable if we have more than one
CPU in the system, and it fixes this issue.
Helge Deller [Sat, 4 Dec 2021 20:14:40 +0000 (21:14 +0100)]
parisc: Fix "make install" on newer debian releases
On newer debian releases the debian-provided "installkernel" script is
installed in /usr/sbin. Fix the kernel install.sh script to look for the
script in this directory as well.
Linus Torvalds [Sat, 4 Dec 2021 16:34:59 +0000 (08:34 -0800)]
Merge tag 'io_uring-5.16-2021-12-03' of git://git.kernel.dk/linux-block
Pull io_uring fix from Jens Axboe:
"Just a single fix preventing repeated retries of task_work based io-wq
thread creation, fixing a regression from when io-wq was made more (a
bit too much) resilient against signals"
* tag 'io_uring-5.16-2021-12-03' of git://git.kernel.dk/linux-block:
io-wq: don't retry task_work creation failure on fatal conditions
Linus Torvalds [Sat, 4 Dec 2021 16:28:42 +0000 (08:28 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two patches, both in drivers.
One is a fix to FC recovery (lpfc) and the other is an enhancement to
support the Intel Alder Motherboard with the UFS driver which comes
under the -rc exception process for hardware enabling"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: ufs-pci: Add support for Intel ADL
scsi: lpfc: Fix non-recovery of remote ports following an unsolicited LOGO
Linus Torvalds [Sat, 4 Dec 2021 16:13:20 +0000 (08:13 -0800)]
Merge tag 'gfs2-v5.16-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fixes from Andreas Gruenbacher:
- Since commit 486408d690e1 ("gfs2: Cancel remote delete work
asynchronously"), inode create and lookup-by-number can overlap more
easily and we can end up with temporary duplicate inodes. Fix the
code to prevent that.
- Fix a BUG demoting weak glock holders from a remote node.
* tag 'gfs2-v5.16-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: gfs2_create_inode rework
gfs2: gfs2_inode_lookup rework
gfs2: gfs2_inode_lookup cleanup
gfs2: Fix remote demote of weak glock holders
Qais Yousef [Thu, 2 Dec 2021 11:20:33 +0000 (11:20 +0000)]
sched/uclamp: Fix rq->uclamp_max not set on first enqueue
Commit d81ae8aac85c ("sched/uclamp: Fix initialization of struct
uclamp_rq") introduced a bug where uclamp_max of the rq is not reset to
match the woken up task's uclamp_max when the rq is idle.
The code was relying on rq->uclamp_max initialized to zero, so on first
enqueue
if (uc_se->value > READ_ONCE(uc_rq->value))
WRITE_ONCE(uc_rq->value, uc_se->value);
}
was actually resetting it. But since commit d81ae8aac85c changed the
default to 1024, this no longer works. And since rq->uclamp_flags is
also initialized to 0, neither above code path nor uclamp_idle_reset()
update the rq->uclamp_max on first wake up from idle.
This is only visible from first wake up(s) until the first dequeue to
idle after enabling the static key. And it only matters if the
uclamp_max of this task is < 1024 since only then its uclamp_max will be
effectively ignored.
Fix it by properly initializing rq->uclamp_flags = UCLAMP_FLAG_IDLE to
ensure uclamp_idle_reset() is called which then will update the rq
uclamp_max value as expected.
Linus Torvalds [Fri, 3 Dec 2021 20:22:56 +0000 (12:22 -0800)]
Merge tag 'pm-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a CPU hot-add issue in the cpufreq core, fix a comment in
the cpufreq core code and update its documentation, and disable the
DTPM (Dynamic Thermal Power Management) code for the time being to
prevent it from causing issues to appear.
Specifics:
- Disable DTPM for this cycle to prevent it from causing issues to
appear on otherwise functional systems (Daniel Lezcano)
- Fix cpufreq sysfs interface failure related to physical CPU hot-add
(Xiongfeng Wang)
- Fix comment in cpufreq core and update its documentation (Tang
Yizhou)"
* tag 'pm-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap: DTPM: Drop unused local variable from init_dtpm()
cpufreq: docs: Update core.rst
cpufreq: Fix a comment in cpufreq_policy_free
powercap/drivers/dtpm: Disable DTPM at boot time
cpufreq: Fix get_cpu_device() failure in add_cpu_dev_symlink()
Linus Torvalds [Fri, 3 Dec 2021 19:46:20 +0000 (11:46 -0800)]
Merge tag 's390-5.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- Fix potential overlap of pseudo-MMIO addresses with MIO addresses
- Fix stack unwinder test case inline assembly compile error that
happens with LLVM's integrated assembler
- Update defconfigs
* tag 's390-5.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfigs
s390/pci: move pseudo-MMIO to prevent MIO overlap
s390/test_unwind: use raw opcode instead of invalid instruction
Linus Torvalds [Fri, 3 Dec 2021 18:50:14 +0000 (10:50 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Three arm64 fixes for -rc4.
One of them is just a trivial documentation fix, whereas the other two
address a warning in the kexec code and a crash in ftrace on systems
implementing BTI.
The latter patch has a couple of ugly ifdefs which Mark plans to clean
up separately, but as-is the patch is straightforward for backporting
to stable kernels.
Summary:
- Add missing BTI landing instructions to the ftrace*_caller
trampolines
- Fix kexec() WARN when DEBUG_VIRTUAL is enabled
- Fix PAC documentation by removing stale references to compiler
flags"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: add missing BTIs
arm64: kexec: use __pa_symbol(empty_zero_page)
arm64: update PAC description for kernel
Linus Torvalds [Fri, 3 Dec 2021 18:44:16 +0000 (10:44 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has another set of driver bugfixes, mostly for the stm32f7 driver"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rk3x: Handle a spurious start completion interrupt flag
i2c: stm32f7: use proper DMAENGINE API for termination
i2c: stm32f7: stop dma transfer in case of NACK
i2c: stm32f7: recover the bus on access timeout
i2c: stm32f7: flush TX FIFO upon transfer errors
i2c: cbus-gpio: set atomic transfer callback
Linus Torvalds [Fri, 3 Dec 2021 18:38:45 +0000 (10:38 -0800)]
Merge tag 'libata-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull libata fixes from Damien Le Moal:
"Two sparse warning fixes and a couple of patches to fix an issue with
sata_fsl driver module removal:
- A couple of patches to avoid sparse warnings in libata-sata and in
the pata_falcon driver (from Yang and Finn).
- A couple of sata_fsl driver patches fixing IRQ free and proc
unregister on module removal (from Baokun)"
* tag 'libata-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: replace snprintf in show functions with sysfs_emit
sata_fsl: fix warning in remove_proc_entry when rmmod sata_fsl
sata_fsl: fix UAF in sata_fsl_port_stop when rmmod sata_fsl
pata_falcon: Avoid type warnings from sparse
Shyam Prasad N [Thu, 2 Dec 2021 07:46:54 +0000 (07:46 +0000)]
cifs: avoid use of dstaddr as key for fscache client cookie
server->dstaddr can change when the DNS mapping for the
server hostname changes. But conn_id is a u64 counter
that is incremented each time a new TCP connection
is setup. So use only that as a key.
Shyam Prasad N [Thu, 2 Dec 2021 07:30:00 +0000 (07:30 +0000)]
cifs: add server conn_id to fscache client cookie
The fscache client cookie uses the server address
(and port) as the cookie key. This is a problem when
nosharesock is used. Two different connections will
use duplicate cookies. Avoid this by adding
server->conn_id to the key, so that it's guaranteed
that cookie will not be duplicated.
Also, for secondary channels of a session, copy the
fscache pointer from the primary channel. The primary
channel is guaranteed not to go away as long as secondary
channels are in use. Also addresses minor problem found
by kernel test robot.
Shyam Prasad N [Thu, 2 Dec 2021 07:14:42 +0000 (07:14 +0000)]
cifs: wait for tcon resource_id before getting fscache super
The logic for initializing tcon->resource_id is done inside
cifs_root_iget. fscache super cookie relies on this for aux
data. So we need to push the fscache initialization to this
later point during mount.
Paulo Alcantara [Thu, 2 Dec 2021 18:29:35 +0000 (15:29 -0300)]
cifs: fix missed refcounting of ipc tcon
Fix missed refcounting of IPC tcon used for getting domain-based DFS
root referrals. We want to keep it alive as long as mount is active
and can be refreshed. For standalone DFS root referrals it wouldn't
be a problem as the client ends up having an IPC tcon for both mount
and cache.
Fixes: c88f7dcd6d64 ("cifs: support nested dfs links over reconnect") Signed-off-by: Paulo Alcantara (SUSE) <[email protected]> Reviewed-by: Enzo Matsumiya <[email protected]> Signed-off-by: Steve French <[email protected]>
In the native case, PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is the
trampoline stack. But XEN pv doesn't use trampoline stack, so
PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is also the kernel stack.
In that case, source and destination stacks are identical, which means
that reusing swapgs_restore_regs_and_return_to_usermode() in XEN pv
would cause %rsp to move up to the top of the kernel stack and leave the
IRET frame below %rsp.
This is dangerous as it can be corrupted if #NMI / #MC hit as either of
these events occurring in the middle of the stack pushing would clobber
data on the (original) stack.
And, with XEN pv, swapgs_restore_regs_and_return_to_usermode() pushing
the IRET frame on to the original address is useless and error-prone
when there is any future attempt to modify the code.
removed a CR3 write in the faulting path of load_gs_index().
But the path's FENCE_SWAPGS_USER_ENTRY has no fence operation if PTI is
enabled, see spectre_v1_select_mitigation().
Rather, it depended on the serializing CR3 write of SWITCH_TO_KERNEL_CR3
and since it got removed, add a FENCE_SWAPGS_KERNEL_ENTRY call to make
sure speculation is blocked.
Linus Torvalds [Wed, 1 Dec 2021 18:06:14 +0000 (10:06 -0800)]
fget: check that the fd still exists after getting a ref to it
Jann Horn points out that there is another possible race wrt Unix domain
socket garbage collection, somewhat reminiscent of the one fixed in
commit cbcf01128d0a ("af_unix: fix garbage collect vs MSG_PEEK").
See the extended comment about the garbage collection requirements added
to unix_peek_fds() by that commit for details.
The race comes from how we can locklessly look up a file descriptor just
as it is in the process of being closed, and with the right artificial
timing (Jann added a few strategic 'mdelay(500)' calls to do that), the
Unix domain socket garbage collector could see the reference count
decrement of the close() happen before fget() took its reference to the
file and the file was attached onto a new file descriptor.
This is all (intentionally) correct on the 'struct file *' side, with
RCU lookups and lockless reference counting very much part of the
design. Getting that reference count out of order isn't a problem per
se.
But the garbage collector can get confused by seeing this situation of
having seen a file not having any remaining external references and then
seeing it being attached to an fd.
In commit cbcf01128d0a ("af_unix: fix garbage collect vs MSG_PEEK") the
fix was to serialize the file descriptor install with the garbage
collector by taking and releasing the unix_gc_lock.
That's not really an option here, but since this all happens when we are
in the process of looking up a file descriptor, we can instead simply
just re-check that the file hasn't been closed in the meantime, and just
re-do the lookup if we raced with a concurrent close() of the same file
descriptor.
Lai Jiangshan [Fri, 26 Nov 2021 10:11:21 +0000 (18:11 +0800)]
x86/entry: Add a fence for kernel entry SWAPGS in paranoid_entry()
Commit
18ec54fdd6d18 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations")
added FENCE_SWAPGS_{KERNEL|USER}_ENTRY for conditional SWAPGS. In
paranoid_entry(), it uses only FENCE_SWAPGS_KERNEL_ENTRY for both
branches. This is because the fence is required for both cases since the
CR3 write is conditional even when PTI is enabled.
But
96b2371413e8f ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
changed the order of SWAPGS and the CR3 write. And it missed the needed
FENCE_SWAPGS_KERNEL_ENTRY for the user gsbase case.
Add it back by changing the branches so that FENCE_SWAPGS_KERNEL_ENTRY
can cover both branches.
[ bp: Massage, fix typos, remove obsolete comment while at it. ]
Michael Sterritt [Fri, 19 Nov 2021 23:27:57 +0000 (15:27 -0800)]
x86/sev: Fix SEV-ES INS/OUTS instructions for word, dword, and qword
Properly type the operands being passed to __put_user()/__get_user().
Otherwise, these routines truncate data for dependent instructions
(e.g., INSW) and only read/write one byte.
This has been tested by sending a string with REP OUTSW to a port and
then reading it back in with REP INSW on the same port.
Previous behavior was to only send and receive the first char of the
size. For example, word operations for "abcd" would only read/write
"ac". With change, the full string is now written and read back.
powercap: DTPM: Drop unused local variable from init_dtpm()
The dtpm_descr variable in init_dtpm() is not used after commit f751db8adaea ("powercap/drivers/dtpm: Disable DTPM at boot time"),
so drop it.
Fixes: f751db8adaea ("powercap/drivers/dtpm: Disable DTPM at boot time") Reported-by: Stephen Rothwell <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
Jens Axboe [Fri, 3 Dec 2021 02:40:15 +0000 (19:40 -0700)]
io-wq: don't retry task_work creation failure on fatal conditions
We don't want to be retrying task_work creation failure if there's
an actual signal pending for the parent task. If we do, then we can
enter an infinite loop of perpetually retrying and each retry failing
with -ERESTARTNOINTR because a signal is pending.
Al Cooper [Wed, 1 Dec 2021 20:14:02 +0000 (15:14 -0500)]
serial: 8250_bcm7271: UART errors after resuming from S2
There is a small window in time during resume where the hardware
flow control signal RTS can be asserted (which allows a sender to
resume sending data to the UART) but the baud rate has not yet
been restored. This will cause corrupted data and FRAMING, OVERRUN
and BREAK errors. This is happening because the MCTRL register is
shadowed in uart_port struct and is later used during resume to set
the MCTRL register during both serial8250_do_startup() and
uart_resume_port(). Unfortunately, serial8250_do_startup()
happens before the UART baud rate is restored. The fix is to clear
the shadowed mctrl value at the end of suspend and restore it at the
end of resume.
Zhou Qingyang [Tue, 30 Nov 2021 17:27:00 +0000 (01:27 +0800)]
usb: cdnsp: Fix a NULL pointer dereference in cdnsp_endpoint_init()
In cdnsp_endpoint_init(), cdnsp_ring_alloc() is assigned to pep->ring
and there is a dereference of it in cdnsp_endpoint_init(), which could
lead to a NULL pointer dereference on failure of cdnsp_ring_alloc().
Fix this bug by adding a check of pep->ring.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_USB_CDNSP_GADGET=y show no new warnings,
and our static analyzer no longer warns about this code.
Frank Li [Tue, 30 Nov 2021 15:42:39 +0000 (09:42 -0600)]
usb: cdns3: gadget: fix new urb never complete if ep cancel previous requests
This issue was found at android12 MTP.
1. MTP submit many out urb request.
2. Cancel left requests (>20) when enough data get from host
3. Send ACK by IN endpoint.
4. MTP submit new out urb request.
5. 4's urb never complete.
usb: typec: tcpm: Wait in SNK_DEBOUNCED until disconnect
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
This change makes TCPM to wait in SNK_DEBOUNCED state until
CC1 and CC2 pins is SNK.Open for at least tPDDebounce. Previously,
TCPM resets the port if vbus is not present in PD_T_PS_SOURCE_ON.
This causes TCPM to loop continuously when connected to a
faulty power source that does not present vbus. Waiting in
SNK_DEBOUNCED also ensures that TCPM is adherant to
"4.5.2.2.4.2 Exiting from AttachWait.SNK State" requirements.
Mathias Nyman [Fri, 26 Nov 2021 12:23:40 +0000 (14:23 +0200)]
xhci: Fix commad ring abort, write all 64 bits to CRCR register.
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Joerg Roedel [Thu, 2 Dec 2021 15:32:26 +0000 (16:32 +0100)]
x86/64/mm: Map all kernel memory into trampoline_pgd
The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff
range of kernel memory (with 4-level paging). This range contains the
kernel's text+data+bss mappings and the module mapping space but not the
direct mapping and the vmalloc area.
This is enough to get the application processors out of real-mode, but
for code that switches back to real-mode the trampoline_pgd is missing
important parts of the address space. For example, consider this code
from arch/x86/kernel/reboot.c, function machine_real_restart() for a
64-bit kernel:
The code switches to the trampoline_pgd, which unmaps the direct mapping
and also the kernel stack. The call to cr4_clear_bits() will find no
stack and crash the machine. The real_mode_header pointer below points
into the direct mapping, and dereferencing it also causes a crash.
The reason this does not crash always is only that kernel mappings are
global and the CR3 switch does not flush those mappings. But if theses
mappings are not in the TLB already, the above code will crash before it
can jump to the real-mode stub.
Extend the trampoline_pgd to contain all kernel mappings to prevent
these crashes and to make code which runs on this page-table more
robust.
Peter Zijlstra [Thu, 2 Dec 2021 20:45:34 +0000 (21:45 +0100)]
objtool: Fix pv_ops noinstr validation
Boris reported that in one of his randconfig builds, objtool got
infinitely stuck. Turns out there's trivial list corruption in the
pv_ops tracking when a function is both in a static table and in a code
assignment.
Avoid re-adding function to the pv_ops[] lists when they're already on
it.
Linus Torvalds [Thu, 2 Dec 2021 22:38:54 +0000 (14:38 -0800)]
Merge tag 'drm-fixes-2021-12-03-1' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Bit of an uptick in patch count this week, though it's all relatively
small overall.
I suspect msm has been queuing up a few fixes to skew it here.
Otherwise amdgpu has a scattered bunch of small fixes, and then some
vc4, i915.
virtio-gpu changes an rc1 introduced uAPI mistake, and makes it
operate more like other drivers. This should be fine as no userspace
relies on the behaviour yet.
* tag 'drm-fixes-2021-12-03-1' of git://anongit.freedesktop.org/drm/drm: (41 commits)
Revert "drm/i915: Implement Wa_1508744258"
drm/amdkfd: process_info lock not needed for svm
drm/amdgpu: adjust the kfd reset sequence in reset sriov function
drm/amd/display: add connector type check for CRC source set
drm/amdkfd: fix double free mem structure
drm/amdkfd: set "r = 0" explicitly before goto
drm/amd/display: Add work around for tunneled MST.
drm/amd/display: Fix for the no Audio bug with Tiled Displays
drm/amd/display: Clear DPCD lane settings after repeater training
drm/amd/display: Allow DSC on supported MST branch devices
drm/amdgpu: Don't halt RLC on GFX suspend
drm/amdgpu: fix the missed handling for SDMA2 and SDMA3
drm/amdgpu: check atomic flag to differeniate with legacy path
drm/amdgpu: cancel the correct hrtimer on exit
drm/amdgpu/sriov/vcn: add new vcn ip revision check case for SIENNA_CICHLID
drm/i915/dp: Perform 30ms delay after source OUI write
dma-buf: system_heap: Use 'for_each_sgtable_sg' in pages free flow
drm/i915: Add support for panels with VESA backlights with PWM enable/disable
drm/vc4: kms: Fix previous HVS commit wait
drm/vc4: kms: Don't duplicate pending commit
...
Dave Airlie [Thu, 2 Dec 2021 19:59:26 +0000 (05:59 +1000)]
Merge tag 'drm-intel-fixes-2021-12-02' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fixing a regression where the backlight brightness control stopped working.
- Fix the Intel HDR backlight support detection.
- Reverting a w/a to fix a gpu Hang in TGL. The w/a itself was also
for a hang, but in a much rarer scenario. The proper solution need
to be done with help from user space and it will be addressed later.
- rds: correct socket tunable error in rds_tcp_tune()
- ipv6: fix memory leak in fib6_rule_suppress
- wireguard: reset peer src endpoint when netns exits
- wireguard: improve resilience to DoS around incoming handshakes
- tcp: fix page frag corruption on page fault which involves TCP
- mpls: fix missing attributes in delete notifications
- mt7915: fix NULL pointer dereference with ad-hoc mode
Misc:
- rt2x00: be more lenient about EPROTO errors during start
- mlx4_en: update reported link modes for 1/10G"
* tag 'net-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (85 commits)
net: dsa: b53: Add SPI ID table
gro: Fix inconsistent indenting
selftests: net: Correct case name
net/rds: correct socket tunable error in rds_tcp_tune()
mctp: Don't let RTM_DELROUTE delete local routes
net/smc: Keep smc_close_final rc during active close
ibmvnic: drop bad optimization in reuse_tx_pools()
ibmvnic: drop bad optimization in reuse_rx_pools()
net/smc: fix wrong list_del in smc_lgr_cleanup_early
Fix Comment of ETH_P_802_3_MIN
ethernet: aquantia: Try MAC address from device tree
ipv4: convert fib_num_tclassid_users to atomic_t
net: avoid uninit-value from tcp_conn_request
net: annotate data-races on txq->xmit_lock_owner
octeontx2-af: Fix a memleak bug in rvu_mbox_init()
net/mlx4_en: Fix an use-after-free bug in mlx4_en_try_alloc_resources()
vrf: Reset IPCB/IP6CB when processing outbound pkts in vrf dev xmit
net: qlogic: qlcnic: Fix a NULL pointer dereference in qlcnic_83xx_add_rings()
net: dsa: mv88e6xxx: Link in pcs_get_state() if AN is bypassed
net: dsa: mv88e6xxx: Fix inband AN for 2500base-x on 88E6393X family
...
Linus Torvalds [Thu, 2 Dec 2021 19:07:41 +0000 (11:07 -0800)]
Merge tag 'trace-v5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Three tracing fixes:
- Allow compares of strings when using signed and unsigned characters
- Fix kmemleak false positive for histogram entries
- Handle negative numbers for user defined kretprobe data sizes"
* tag 'trace-v5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
kprobes: Limit max data_size of the kretprobe instances
tracing: Fix a kmemleak false positive in tracing_map
tracing/histograms: String compares should not care about signed values
Linus Torvalds [Thu, 2 Dec 2021 18:56:16 +0000 (10:56 -0800)]
Merge tag 'for-linus-5.16-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI fixes from Corey Minyard:
"Some changes that went in 5.16 had issues. When working on the design
a piece was redesigned and things got missed. And the message type was
not being initialized when it was allocated, resulting in crashes.
In addition, the IPMI driver has had a shutdown issue where it could
still have an item in a system workqueue after it had been shutdown.
Move to a private workqueue to avoid that problem"
* tag 'for-linus-5.16-2' of git://github.com/cminyard/linux-ipmi:
ipmi:ipmb: Fix unknown command response
ipmi: fix IPMI_SMI_MSG_TYPE_IPMB_DIRECT response length checking
ipmi: fix oob access due to uninit smi_msg type
ipmi: msghandler: Make symbol 'remove_work_wq' static
ipmi: Move remove_work to dedicated workqueue
sched/cputime: Fix getrusage(RUSAGE_THREAD) with nohz_full
getrusage(RUSAGE_THREAD) with nohz_full may return shorter utime/stime
than the actual time.
task_cputime_adjusted() snapshots utime and stime and then adjust their
sum to match the scheduler maintained cputime.sum_exec_runtime.
Unfortunately in nohz_full, sum_exec_runtime is only updated once per
second in the worst case, causing a discrepancy against utime and stime
that can be updated anytime by the reader using vtime.
To fix this situation, perform an update of cputime.sum_exec_runtime
when the cputime snapshot reports the task as actually running while
the tick is disabled. The related overhead is then contained within the
relevant situations.
timers/nohz: Last resort update jiffies on nohz_full IRQ entry
When at least one CPU runs in nohz_full mode, a dedicated timekeeper CPU
is guaranteed to stay online and to never stop its tick.
Meanwhile on some rare case, the dedicated timekeeper may be running
with interrupts disabled for a while, such as in stop_machine.
If jiffies stop being updated, a nohz_full CPU may end up endlessly
programming the next tick in the past, taking the last jiffies update
monotonic timestamp as a stale base, resulting in an tick storm.
Here is a scenario where it matters:
0) CPU 0 is the timekeeper and CPU 1 a nohz_full CPU.
1) A stop machine callback is queued to execute somewhere.
2) CPU 0 reaches MULTI_STOP_DISABLE_IRQ while CPU 1 is still in
MULTI_STOP_PREPARE. Hence CPU 0 can't do its timekeeping duty. CPU 1
can still take IRQs.
3) CPU 1 receives an IRQ which queues a timer callback one jiffy forward.
4) On IRQ exit, CPU 1 schedules the tick one jiffy forward, taking
last_jiffies_update as a base. But last_jiffies_update hasn't been
updated for 2 jiffies since the timekeeper has interrupts disabled.
5) clockevents_program_event(), which relies on ktime_get(), observes
that the expiration is in the past and therefore programs the min
delta event on the clock.
6) The tick fires immediately, goto 3)
7) Tick storm, the nohz_full CPU is drown and takes ages to reach
MULTI_STOP_DISABLE_IRQ, which is the only way out of this situation.
Solve this with unconditionally updating jiffies if the value is stale
on nohz_full IRQ entry. IRQs and other disturbances are expected to be
rare enough on nohz_full for the unconditional call to ktime_get() to
actually matter.
Currently autoloading for SPI devices does not use the DT ID table, it
uses SPI modalises. Supporting OF modalises is going to be difficult if
not impractical, an attempt was made but has been reverted, so ensure
that module autoloading works for this driver by adding an id_table
listing the SPI IDs for everything.
Fixes: 96c8395e2166 ("spi: Revert modalias changes") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net/rds: correct socket tunable error in rds_tcp_tune()
Correct an error where setting /proc/sys/net/rds/tcp/rds_tcp_rcvbuf would
instead modify the socket's sk_sndbuf and would leave sk_rcvbuf untouched.
Fixes: c6a58ffed536 ("RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket") Signed-off-by: William Kucharski <[email protected]> Acked-by: Santosh Shilimkar <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Matt Johnston [Wed, 1 Dec 2021 08:07:42 +0000 (16:07 +0800)]
mctp: Don't let RTM_DELROUTE delete local routes
We need to test against the existing route type, not
the rtm_type in the netlink request.
Fixes: 83f0a0b7285b ("mctp: Specify route types, require rtm_type in RTM_*ROUTE messages") Signed-off-by: Matt Johnston <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Tony Lu [Wed, 1 Dec 2021 06:42:16 +0000 (14:42 +0800)]
net/smc: Keep smc_close_final rc during active close
When smc_close_final() returns error, the return code overwrites by
kernel_sock_shutdown() in smc_close_active(). The return code of
smc_close_final() is more important than kernel_sock_shutdown(), and it
will pass to userspace directly.
Fix it by keeping both return codes, if smc_close_final() raises an
error, return it or kernel_sock_shutdown()'s.
ibmvnic: drop bad optimization in reuse_tx_pools()
When trying to decide whether or not reuse existing rx/tx pools
we tried to allow a range of values for the pool parameters rather
than exact matches. This was intended to reuse the resources for
instance when switching between two VIO servers with different
default parameters.
But this optimization is incomplete and breaks when we try to
change the number of queues for instance. The optimization needs
to be updated, so drop it for now and simplify the code.
projects / linux.git / log