Rafael J. Wysocki [Fri, 1 Feb 2019 10:05:27 +0000 (11:05 +0100)]
Merge branch 'pm-cpuidle-fixes'
* pm-cpuidle-fixes:
cpuidle: poll_state: Fix default time limit
Linus Torvalds [Fri, 1 Feb 2019 07:22:57 +0000 (23:22 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Mostly driver fixes, but there's a core framework fix in here too:
- Revert the commits that introduce clk management for the SP clk on
MMP2 SoCs (used for OLPC). Turns out it wasn't a good idea and
there isn't any need to manage this clk, it just causes more
headaches.
- A performance regression that went unnoticed for many years where
we would traverse the entire clk tree looking for a clk by name
when we already have the pointer to said clk that we're looking for
- A parent linkage fix for the qcom SDM845 clk driver
- An i.MX clk driver rate miscalculation fix where order of
operations were messed up
- One error handling fix from the static checkers"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gcc: Use active only source for CPUSS clocks
clk: ti: Fix error handling in ti_clk_parse_divider_data()
clk: imx: Fix fractional clock set rate computation
clk: Remove global clk traversal on fetch parent index
Revert "dt-bindings: marvell,mmp2: Add clock id for the SP clock"
Revert "clk: mmp2: add SP clock"
Revert "Input: olpc_apsp - enable the SP clock"
Linus Torvalds [Fri, 1 Feb 2019 07:09:00 +0000 (23:09 -0800)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a bug in cavium/nitrox where the callback is invoked prior
to the DMA unmap"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: cavium/nitrox - Invoke callback after DMA unmap
Linus Torvalds [Fri, 1 Feb 2019 07:06:17 +0000 (23:06 -0800)]
Merge tag 'pci-v5.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Revert armada8k GPIO reset change that broke Macchiatobin booting
(Baruch Siach)
- Use actual size config reads on ARM cns3xxx (Koen Vandeputte)
- Fix ARM cns3xxx config write alignment issue (Koen Vandeputte)
- Fix imx6 PHY device link error checking (Leonard Crestez)
- Fix imx6 probe failure on chips without separate PCI power domain
(Leonard Crestez)
* tag 'pci-v5.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: armada8k: Add support for gpio controlled reset signal"
ARM: cns3xxx: Use actual size reads for PCIe
ARM: cns3xxx: Fix writing to wrong PCI config registers after alignment
PCI: imx: Fix checking pd_pcie_phy device link addition
PCI: imx: Fix probe failure without power domain
Huang Rui [Wed, 30 Jan 2019 11:50:04 +0000 (19:50 +0800)]
drm/amdgpu: fix the incorrect external id for raven series
This patch fixes the incorrect external id that kernel reports to user mode
driver. Raven2's rev_id is starts from 0x8, so its external id (0x81) should
start from rev_id + 0x79 (0x81 - 0x8). And Raven's rev_id should be 0x21 while
rev_id == 1.
Reported-by: Crystal Jin <Crystal.Jin@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jay Cornwall [Wed, 30 Jan 2019 18:53:29 +0000 (12:53 -0600)]
drm/amdgpu: Implement doorbell self-ring for NBIO 7.4
Fixes doorbell reflection on Vega20.
Change-Id: I0495139d160a9032dff5977289b1eec11c16f781
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Roman Li [Thu, 17 Jan 2019 20:47:54 +0000 (15:47 -0500)]
drm/amd/display: Fix fclk idle state
[Why]
The earlier change 'Fix 6x4K displays' led to fclk value
idling at higher DPM level.
[How]
Apply the fix only to respective multi-display configuration.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel Borkmann [Thu, 31 Jan 2019 22:18:22 +0000 (23:18 +0100)]
Merge branch 'bpf-lockdep-fixes'
Alexei Starovoitov says:
====================
v1->v2:
- reworded 2nd patch. It's a real dead lock. Not a false positive
- dropped the lockdep fix for up_read_non_owner in bpf_get_stackid
In addition to preempt_disable patch for socket filters
https://patchwork.ozlabs.org/patch/
1032437/
First patch fixes lockdep false positive in percpu_freelist
Second patch fixes potential deadlock in bpf_prog_register
Third patch fixes another potential deadlock in stackmap access
from tracing bpf prog and from syscall.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Martin KaFai Lau [Thu, 31 Jan 2019 02:12:45 +0000 (18:12 -0800)]
bpf: Fix syscall's stackmap lookup potential deadlock
The map_lookup_elem used to not acquiring spinlock
in order to optimize the reader.
It was true until commit
557c0c6e7df8 ("bpf: convert stackmap to pre-allocation")
The syscall's map_lookup_elem(stackmap) calls bpf_stackmap_copy().
bpf_stackmap_copy() may find the elem no longer needed after the copy is done.
If that is the case, pcpu_freelist_push() saves this elem for reuse later.
This push requires a spinlock.
If a tracing bpf_prog got run in the middle of the syscall's
map_lookup_elem(stackmap) and this tracing bpf_prog is calling
bpf_get_stackid(stackmap) which also requires the same pcpu_freelist's
spinlock, it may end up with a dead lock situation as reported by
Eric Dumazet in https://patchwork.ozlabs.org/patch/
1030266/
The situation is the same as the syscall's map_update_elem() which
needs to acquire the pcpu_freelist's spinlock and could race
with tracing bpf_prog. Hence, this patch fixes it by protecting
bpf_stackmap_copy() with this_cpu_inc(bpf_prog_active)
to prevent tracing bpf_prog from running.
A later syscall's map_lookup_elem commit
f1a2e44a3aec ("bpf: add queue and stack maps")
also acquires a spinlock and races with tracing bpf_prog similarly.
Hence, this patch is forward looking and protects the majority
of the map lookups. bpf_map_offload_lookup_elem() is the exception
since it is for network bpf_prog only (i.e. never called by tracing
bpf_prog).
Fixes: 557c0c6e7df8 ("bpf: convert stackmap to pre-allocation")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Alexei Starovoitov [Thu, 31 Jan 2019 02:12:44 +0000 (18:12 -0800)]
bpf: fix potential deadlock in bpf_prog_register
Lockdep found a potential deadlock between cpu_hotplug_lock, bpf_event_mutex, and cpuctx_mutex:
[ 13.007000] WARNING: possible circular locking dependency detected
[ 13.007587]
5.0.0-rc3-00018-g2fa53f892422-dirty #477 Not tainted
[ 13.008124] ------------------------------------------------------
[ 13.008624] test_progs/246 is trying to acquire lock:
[ 13.009030]
0000000094160d1d (tracepoints_mutex){+.+.}, at: tracepoint_probe_register_prio+0x2d/0x300
[ 13.009770]
[ 13.009770] but task is already holding lock:
[ 13.010239]
00000000d663ef86 (bpf_event_mutex){+.+.}, at: bpf_probe_register+0x1d/0x60
[ 13.010877]
[ 13.010877] which lock already depends on the new lock.
[ 13.010877]
[ 13.011532]
[ 13.011532] the existing dependency chain (in reverse order) is:
[ 13.012129]
[ 13.012129] -> #4 (bpf_event_mutex){+.+.}:
[ 13.012582] perf_event_query_prog_array+0x9b/0x130
[ 13.013016] _perf_ioctl+0x3aa/0x830
[ 13.013354] perf_ioctl+0x2e/0x50
[ 13.013668] do_vfs_ioctl+0x8f/0x6a0
[ 13.014003] ksys_ioctl+0x70/0x80
[ 13.014320] __x64_sys_ioctl+0x16/0x20
[ 13.014668] do_syscall_64+0x4a/0x180
[ 13.015007] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 13.015469]
[ 13.015469] -> #3 (&cpuctx_mutex){+.+.}:
[ 13.015910] perf_event_init_cpu+0x5a/0x90
[ 13.016291] perf_event_init+0x1b2/0x1de
[ 13.016654] start_kernel+0x2b8/0x42a
[ 13.016995] secondary_startup_64+0xa4/0xb0
[ 13.017382]
[ 13.017382] -> #2 (pmus_lock){+.+.}:
[ 13.017794] perf_event_init_cpu+0x21/0x90
[ 13.018172] cpuhp_invoke_callback+0xb3/0x960
[ 13.018573] _cpu_up+0xa7/0x140
[ 13.018871] do_cpu_up+0xa4/0xc0
[ 13.019178] smp_init+0xcd/0xd2
[ 13.019483] kernel_init_freeable+0x123/0x24f
[ 13.019878] kernel_init+0xa/0x110
[ 13.020201] ret_from_fork+0x24/0x30
[ 13.020541]
[ 13.020541] -> #1 (cpu_hotplug_lock.rw_sem){++++}:
[ 13.021051] static_key_slow_inc+0xe/0x20
[ 13.021424] tracepoint_probe_register_prio+0x28c/0x300
[ 13.021891] perf_trace_event_init+0x11f/0x250
[ 13.022297] perf_trace_init+0x6b/0xa0
[ 13.022644] perf_tp_event_init+0x25/0x40
[ 13.023011] perf_try_init_event+0x6b/0x90
[ 13.023386] perf_event_alloc+0x9a8/0xc40
[ 13.023754] __do_sys_perf_event_open+0x1dd/0xd30
[ 13.024173] do_syscall_64+0x4a/0x180
[ 13.024519] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 13.024968]
[ 13.024968] -> #0 (tracepoints_mutex){+.+.}:
[ 13.025434] __mutex_lock+0x86/0x970
[ 13.025764] tracepoint_probe_register_prio+0x2d/0x300
[ 13.026215] bpf_probe_register+0x40/0x60
[ 13.026584] bpf_raw_tracepoint_open.isra.34+0xa4/0x130
[ 13.027042] __do_sys_bpf+0x94f/0x1a90
[ 13.027389] do_syscall_64+0x4a/0x180
[ 13.027727] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 13.028171]
[ 13.028171] other info that might help us debug this:
[ 13.028171]
[ 13.028807] Chain exists of:
[ 13.028807] tracepoints_mutex --> &cpuctx_mutex --> bpf_event_mutex
[ 13.028807]
[ 13.029666] Possible unsafe locking scenario:
[ 13.029666]
[ 13.030140] CPU0 CPU1
[ 13.030510] ---- ----
[ 13.030875] lock(bpf_event_mutex);
[ 13.031166] lock(&cpuctx_mutex);
[ 13.031645] lock(bpf_event_mutex);
[ 13.032135] lock(tracepoints_mutex);
[ 13.032441]
[ 13.032441] *** DEADLOCK ***
[ 13.032441]
[ 13.032911] 1 lock held by test_progs/246:
[ 13.033239] #0:
00000000d663ef86 (bpf_event_mutex){+.+.}, at: bpf_probe_register+0x1d/0x60
[ 13.033909]
[ 13.033909] stack backtrace:
[ 13.034258] CPU: 1 PID: 246 Comm: test_progs Not tainted
5.0.0-rc3-00018-g2fa53f892422-dirty #477
[ 13.034964] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
[ 13.035657] Call Trace:
[ 13.035859] dump_stack+0x5f/0x8b
[ 13.036130] print_circular_bug.isra.37+0x1ce/0x1db
[ 13.036526] __lock_acquire+0x1158/0x1350
[ 13.036852] ? lock_acquire+0x98/0x190
[ 13.037154] lock_acquire+0x98/0x190
[ 13.037447] ? tracepoint_probe_register_prio+0x2d/0x300
[ 13.037876] __mutex_lock+0x86/0x970
[ 13.038167] ? tracepoint_probe_register_prio+0x2d/0x300
[ 13.038600] ? tracepoint_probe_register_prio+0x2d/0x300
[ 13.039028] ? __mutex_lock+0x86/0x970
[ 13.039337] ? __mutex_lock+0x24a/0x970
[ 13.039649] ? bpf_probe_register+0x1d/0x60
[ 13.039992] ? __bpf_trace_sched_wake_idle_without_ipi+0x10/0x10
[ 13.040478] ? tracepoint_probe_register_prio+0x2d/0x300
[ 13.040906] tracepoint_probe_register_prio+0x2d/0x300
[ 13.041325] bpf_probe_register+0x40/0x60
[ 13.041649] bpf_raw_tracepoint_open.isra.34+0xa4/0x130
[ 13.042068] ? __might_fault+0x3e/0x90
[ 13.042374] __do_sys_bpf+0x94f/0x1a90
[ 13.042678] do_syscall_64+0x4a/0x180
[ 13.042975] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 13.043382] RIP: 0033:0x7f23b10a07f9
[ 13.045155] RSP: 002b:
00007ffdef42fdd8 EFLAGS:
00000202 ORIG_RAX:
0000000000000141
[ 13.045759] RAX:
ffffffffffffffda RBX:
00007ffdef42ff70 RCX:
00007f23b10a07f9
[ 13.046326] RDX:
0000000000000070 RSI:
00007ffdef42fe10 RDI:
0000000000000011
[ 13.046893] RBP:
00007ffdef42fdf0 R08:
0000000000000038 R09:
00007ffdef42fe10
[ 13.047462] R10:
0000000000000000 R11:
0000000000000202 R12:
0000000000000000
[ 13.048029] R13:
0000000000000016 R14:
00007f23b1db4690 R15:
0000000000000000
Since tracepoints_mutex will be taken in tracepoint_probe_register/unregister()
there is no need to take bpf_event_mutex too.
bpf_event_mutex is protecting modifications to prog array used in kprobe/perf bpf progs.
bpf_raw_tracepoints don't need to take this mutex.
Fixes: c4f6699dfcb8 ("bpf: introduce BPF_RAW_TRACEPOINT")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Alexei Starovoitov [Thu, 31 Jan 2019 02:12:43 +0000 (18:12 -0800)]
bpf: fix lockdep false positive in percpu_freelist
Lockdep warns about false positive:
[ 12.492084]
00000000e6b28347 (&head->lock){+...}, at: pcpu_freelist_push+0x2a/0x40
[ 12.492696] but this lock was taken by another, HARDIRQ-safe lock in the past:
[ 12.493275] (&rq->lock){-.-.}
[ 12.493276]
[ 12.493276]
[ 12.493276] and interrupts could create inverse lock ordering between them.
[ 12.493276]
[ 12.494435]
[ 12.494435] other info that might help us debug this:
[ 12.494979] Possible interrupt unsafe locking scenario:
[ 12.494979]
[ 12.495518] CPU0 CPU1
[ 12.495879] ---- ----
[ 12.496243] lock(&head->lock);
[ 12.496502] local_irq_disable();
[ 12.496969] lock(&rq->lock);
[ 12.497431] lock(&head->lock);
[ 12.497890] <Interrupt>
[ 12.498104] lock(&rq->lock);
[ 12.498368]
[ 12.498368] *** DEADLOCK ***
[ 12.498368]
[ 12.498837] 1 lock held by dd/276:
[ 12.499110] #0:
00000000c58cb2ee (rcu_read_lock){....}, at: trace_call_bpf+0x5e/0x240
[ 12.499747]
[ 12.499747] the shortest dependencies between 2nd lock and 1st lock:
[ 12.500389] -> (&rq->lock){-.-.} {
[ 12.500669] IN-HARDIRQ-W at:
[ 12.500934] _raw_spin_lock+0x2f/0x40
[ 12.501373] scheduler_tick+0x4c/0xf0
[ 12.501812] update_process_times+0x40/0x50
[ 12.502294] tick_periodic+0x27/0xb0
[ 12.502723] tick_handle_periodic+0x1f/0x60
[ 12.503203] timer_interrupt+0x11/0x20
[ 12.503651] __handle_irq_event_percpu+0x43/0x2c0
[ 12.504167] handle_irq_event_percpu+0x20/0x50
[ 12.504674] handle_irq_event+0x37/0x60
[ 12.505139] handle_level_irq+0xa7/0x120
[ 12.505601] handle_irq+0xa1/0x150
[ 12.506018] do_IRQ+0x77/0x140
[ 12.506411] ret_from_intr+0x0/0x1d
[ 12.506834] _raw_spin_unlock_irqrestore+0x53/0x60
[ 12.507362] __setup_irq+0x481/0x730
[ 12.507789] setup_irq+0x49/0x80
[ 12.508195] hpet_time_init+0x21/0x32
[ 12.508644] x86_late_time_init+0xb/0x16
[ 12.509106] start_kernel+0x390/0x42a
[ 12.509554] secondary_startup_64+0xa4/0xb0
[ 12.510034] IN-SOFTIRQ-W at:
[ 12.510305] _raw_spin_lock+0x2f/0x40
[ 12.510772] try_to_wake_up+0x1c7/0x4e0
[ 12.511220] swake_up_locked+0x20/0x40
[ 12.511657] swake_up_one+0x1a/0x30
[ 12.512070] rcu_process_callbacks+0xc5/0x650
[ 12.512553] __do_softirq+0xe6/0x47b
[ 12.512978] irq_exit+0xc3/0xd0
[ 12.513372] smp_apic_timer_interrupt+0xa9/0x250
[ 12.513876] apic_timer_interrupt+0xf/0x20
[ 12.514343] default_idle+0x1c/0x170
[ 12.514765] do_idle+0x199/0x240
[ 12.515159] cpu_startup_entry+0x19/0x20
[ 12.515614] start_kernel+0x422/0x42a
[ 12.516045] secondary_startup_64+0xa4/0xb0
[ 12.516521] INITIAL USE at:
[ 12.516774] _raw_spin_lock_irqsave+0x38/0x50
[ 12.517258] rq_attach_root+0x16/0xd0
[ 12.517685] sched_init+0x2f2/0x3eb
[ 12.518096] start_kernel+0x1fb/0x42a
[ 12.518525] secondary_startup_64+0xa4/0xb0
[ 12.518986] }
[ 12.519132] ... key at: [<
ffffffff82b7bc28>] __key.71384+0x0/0x8
[ 12.519649] ... acquired at:
[ 12.519892] pcpu_freelist_pop+0x7b/0xd0
[ 12.520221] bpf_get_stackid+0x1d2/0x4d0
[ 12.520563] ___bpf_prog_run+0x8b4/0x11a0
[ 12.520887]
[ 12.521008] -> (&head->lock){+...} {
[ 12.521292] HARDIRQ-ON-W at:
[ 12.521539] _raw_spin_lock+0x2f/0x40
[ 12.521950] pcpu_freelist_push+0x2a/0x40
[ 12.522396] bpf_get_stackid+0x494/0x4d0
[ 12.522828] ___bpf_prog_run+0x8b4/0x11a0
[ 12.523296] INITIAL USE at:
[ 12.523537] _raw_spin_lock+0x2f/0x40
[ 12.523944] pcpu_freelist_populate+0xc0/0x120
[ 12.524417] htab_map_alloc+0x405/0x500
[ 12.524835] __do_sys_bpf+0x1a3/0x1a90
[ 12.525253] do_syscall_64+0x4a/0x180
[ 12.525659] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 12.526167] }
[ 12.526311] ... key at: [<
ffffffff838f7668>] __key.13130+0x0/0x8
[ 12.526812] ... acquired at:
[ 12.527047] __lock_acquire+0x521/0x1350
[ 12.527371] lock_acquire+0x98/0x190
[ 12.527680] _raw_spin_lock+0x2f/0x40
[ 12.527994] pcpu_freelist_push+0x2a/0x40
[ 12.528325] bpf_get_stackid+0x494/0x4d0
[ 12.528645] ___bpf_prog_run+0x8b4/0x11a0
[ 12.528970]
[ 12.529092]
[ 12.529092] stack backtrace:
[ 12.529444] CPU: 0 PID: 276 Comm: dd Not tainted
5.0.0-rc3-00018-g2fa53f892422 #475
[ 12.530043] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
[ 12.530750] Call Trace:
[ 12.530948] dump_stack+0x5f/0x8b
[ 12.531248] check_usage_backwards+0x10c/0x120
[ 12.531598] ? ___bpf_prog_run+0x8b4/0x11a0
[ 12.531935] ? mark_lock+0x382/0x560
[ 12.532229] mark_lock+0x382/0x560
[ 12.532496] ? print_shortest_lock_dependencies+0x180/0x180
[ 12.532928] __lock_acquire+0x521/0x1350
[ 12.533271] ? find_get_entry+0x17f/0x2e0
[ 12.533586] ? find_get_entry+0x19c/0x2e0
[ 12.533902] ? lock_acquire+0x98/0x190
[ 12.534196] lock_acquire+0x98/0x190
[ 12.534482] ? pcpu_freelist_push+0x2a/0x40
[ 12.534810] _raw_spin_lock+0x2f/0x40
[ 12.535099] ? pcpu_freelist_push+0x2a/0x40
[ 12.535432] pcpu_freelist_push+0x2a/0x40
[ 12.535750] bpf_get_stackid+0x494/0x4d0
[ 12.536062] ___bpf_prog_run+0x8b4/0x11a0
It has been explained that is a false positive here:
https://lkml.org/lkml/2018/7/25/756
Recap:
- stackmap uses pcpu_freelist
- The lock in pcpu_freelist is a percpu lock
- stackmap is only used by tracing bpf_prog
- A tracing bpf_prog cannot be run if another bpf_prog
has already been running (ensured by the percpu bpf_prog_active counter).
Eric pointed out that this lockdep splats stops other
legit lockdep splats in selftests/bpf/test_progs.c.
Fix this by calling local_irq_save/restore for stackmap.
Another false positive had also been worked around by calling
local_irq_save in commit
89ad2fa3f043 ("bpf: fix lockdep splat").
That commit added unnecessary irq_save/restore to fast path of
bpf hash map. irqs are already disabled at that point, since htab
is holding per bucket spin_lock with irqsave.
Let's reduce overhead for htab by introducing __pcpu_freelist_push/pop
function w/o irqsave and convert pcpu_freelist_push/pop to irqsave
to be used elsewhere (right now only in stackmap).
It stops lockdep false positive in stackmap with a bit of acceptable overhead.
Fixes: 557c0c6e7df8 ("bpf: convert stackmap to pre-allocation")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Alexei Starovoitov [Tue, 29 Jan 2019 02:43:34 +0000 (18:43 -0800)]
bpf: run bpf programs with preemption disabled
Disabled preemption is necessary for proper access to per-cpu maps
from BPF programs.
But the sender side of socket filters didn't have preemption disabled:
unix_dgram_sendmsg->sk_filter->sk_filter_trim_cap->bpf_prog_run_save_cb->BPF_PROG_RUN
and a combination of af_packet with tun device didn't disable either:
tpacket_snd->packet_direct_xmit->packet_pick_tx_queue->ndo_select_queue->
tun_select_queue->tun_ebpf_select_queue->bpf_prog_run_clear_cb->BPF_PROG_RUN
Disable preemption before executing BPF programs (both classic and extended).
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Martynas Pumputis [Thu, 31 Jan 2019 09:19:33 +0000 (10:19 +0100)]
bpf, selftests: fix handling of sparse CPU allocations
Previously, bpf_num_possible_cpus() had a bug when calculating a
number of possible CPUs in the case of sparse CPU allocations, as
it was considering only the first range or element of
/sys/devices/system/cpu/possible.
E.g. in the case of "0,2-3" (CPU 1 is not available), the function
returned 1 instead of 3.
This patch fixes the function by making it parse all CPU ranges and
elements.
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Baruch Siach [Thu, 31 Jan 2019 21:00:18 +0000 (15:00 -0600)]
Revert "PCI: armada8k: Add support for gpio controlled reset signal"
Revert commit
3d71746c42 ("PCI: armada8k: Add support for gpio controlled
reset signal").
That commit breaks boot on Macchiatobin board when a Mellanox NIC is
present in the PCIe slot.
It turns out that full reset cycle requires first comphy serdes
initialization. Reset signal toggle without comphy initialization makes
access to PCI configuration registers stall indefinitely. U-Boot toggles
the Macchiatobin PCIe reset line already at boot, after initializing the
comphy serdes.
So while commit
3d71746c42 ("PCI: armada8k: Add support for gpio controlled
reset signal") enables PCIe on platforms that U-Boot does not touch the
reset line (like Clearfog GT-8K), it breaks PCIe (and boot) on the
Macchiatobin board.
Revert commit
3d71746c42 ("PCI: armada8k: Add support for gpio controlled
reset signal") entirely to fix the Macchiatobin regression.
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Koen Vandeputte [Thu, 31 Jan 2019 21:00:11 +0000 (15:00 -0600)]
ARM: cns3xxx: Use actual size reads for PCIe
commit
802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") reimplemented cns3xxx_pci_read_config() using
pci_generic_config_read32(), which preserved the property of only doing
32-bit reads.
It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.
Given that:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended
Allow read access of any size by replacing pci_generic_config_read32()
with the pci_generic_config_read() accessors.
Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Krzysztof Halasa <khalasa@piap.pl>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
CC: Tim Harvey <tharvey@gateworks.com>
Koen Vandeputte [Thu, 31 Jan 2019 21:00:01 +0000 (15:00 -0600)]
ARM: cns3xxx: Fix writing to wrong PCI config registers after alignment
Originally, cns3xxx used its own functions for mapping, reading and
writing config registers.
Commit
802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") removed the internal PCI config write function in favor of
the generic one:
cns3xxx_pci_write_config() --> pci_generic_config_write()
cns3xxx_pci_write_config() expected aligned addresses, being produced by
cns3xxx_pci_map_bus() while the generic one pci_generic_config_write()
actually expects the real address as both the function and hardware are
capable of byte-aligned writes.
This currently leads to pci_generic_config_write() writing to the wrong
registers.
For instance, upon ath9k module loading:
- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER,
located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C
(CACHE_LINE_SIZE)
Fix the bug by removing the alignment in the cns3xxx mapping function.
Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org # v4.0+
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
Leonard Crestez [Thu, 31 Jan 2019 20:59:56 +0000 (14:59 -0600)]
PCI: imx: Fix checking pd_pcie_phy device link addition
The check on the device_link_add() return value is wrong;
this leads to erroneous code execution, so fix it.
Fixes: 3f7cceeab895 ("PCI: imx: Add multi-pd support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Leonard Crestez [Thu, 31 Jan 2019 20:59:50 +0000 (14:59 -0600)]
PCI: imx: Fix probe failure without power domain
On chips without a separate power domain for PCI (such as 6q/6qp) the
imx6_pcie_attach_pd() function incorrectly returns an error.
Fix by returning 0 if dev_pm_domain_attach_by_name() does not find
anything.
Fixes: 3f7cceeab895 ("PCI: imx: Add multi-pd support")
Reported-by: Lukas F.Hartmann <lukas@mntmn.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Michael Chan [Thu, 31 Jan 2019 19:31:48 +0000 (14:31 -0500)]
bnxt_en: Disable interrupts when allocating CP rings or NQs.
When calling firmware to allocate a CP ring or NQ, an interrupt associated
with that ring may be generated immediately before the doorbell is even
setup after the firmware call returns. When servicing the interrupt, the
driver may crash when trying to access the doorbell.
Fix it by disabling interrupt on that vector until the doorbell is
set up.
Fixes: 697197e5a173 ("bnxt_en: Re-structure doorbells.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Gruenbacher [Wed, 30 Jan 2019 20:30:36 +0000 (21:30 +0100)]
gfs2: Revert "Fix loop in gfs2_rbm_find"
This reverts commit
2d29f6b96d8f80322ed2dd895bca590491c38d34.
It turns out that the fix can lead to a ~20 percent performance regression
in initial writes to the page cache according to iozone. Let's revert this
for now to have more time for a proper fix.
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 31 Jan 2019 19:11:18 +0000 (11:11 -0800)]
Merge tag 'linux-kselftest-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This consists of run-time fixes to cpu-hotplug, and seccomp tests,
compile fixes to ir, net, and timers Makefiles"
* tag 'linux-kselftest-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: timers: use LDLIBS instead of LDFLAGS
selftests: net: use LDLIBS instead of LDFLAGS
selftests/seccomp: Enhance per-arch ptrace syscall skip tests
selftests: Use lirc.h from kernel tree, not from system
selftests: cpu-hotplug: fix case where CPUs offline > CPUs present
Greg Kroah-Hartman [Thu, 31 Jan 2019 09:43:16 +0000 (17:43 +0800)]
serial: fix race between flush_to_ldisc and tty_open
There still is a race window after the commit
b027e2298bd588
("tty: fix data race between tty_init_dev and flush of buf"),
and we encountered this crash issue if receive_buf call comes
before tty initialization completes in tty_open and
tty->driver_data may be NULL.
CPU0 CPU1
---- ----
tty_open
tty_init_dev
tty_ldisc_unlock
schedule
flush_to_ldisc
receive_buf
tty_port_default_receive_buf
tty_ldisc_receive_buf
n_tty_receive_buf_common
__receive_buf
uart_flush_chars
uart_start
/*tty->driver_data is NULL*/
tty->ops->open
/*init tty->driver_data*/
it can be fixed by extending ldisc semaphore lock in tty_init_dev
to driver_data initialized completely after tty->ops->open(), but
this will lead to get lock on one function and unlock in some other
function, and hard to maintain, so fix this race only by checking
tty->driver_data when receiving, and return if tty->driver_data
is NULL, and n_tty_receive_buf_common maybe calls uart_unthrottle,
so add the same check.
Because the tty layer knows nothing about the driver associated with the
device, the tty layer can not do anything here, it is up to the tty
driver itself to check for this type of race. Fix up the serial driver
to correctly check to see if it is finished binding with the device when
being called, and if not, abort the tty calls.
[Description and problem report and testing from Li RongQing, I rewrote
the patch to be in the serial layer, not in the tty core - gregkh]
Reported-by: Li RongQing <lirongqing@baidu.com>
Tested-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Wang Li <wangli39@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 31 Jan 2019 18:13:05 +0000 (10:13 -0800)]
Merge tag 'nfs-for-5.0-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"This addresses two bugs, one in the error code handling of
nfs_page_async_flush() and one to fix a potential NULL pointer
dereference in nfs_parse_devname().
Stable bugfix:
- Fix up return value on fatal errors in nfs_page_async_flush()
Other bugfix:
- Fix NULL pointer dereference of dev_name"
* tag 'nfs-for-5.0-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Fix up return value on fatal errors in nfs_page_async_flush()
nfs: Fix NULL pointer dereference of dev_name
Linus Torvalds [Thu, 31 Jan 2019 18:00:00 +0000 (10:00 -0800)]
Merge tag 'sound-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Only three fixes.
The fix for Realtek HD-audio looks lengthy, but it's just a code
shuffling, and the actual changes are fairly small.
The rest are a PCM core fix for a long-standing bug that was recently
scratched by syzkaller, and a trivial USB-audio quirk for DSD support"
* tag 'sound-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fixed hp_pin no value
ALSA: pcm: Fix tight loop of OSS capture stream
ALSA: usb-audio: Add Opus #3 to quirks for native DSD support
David S. Miller [Thu, 31 Jan 2019 17:47:56 +0000 (09:47 -0800)]
Merge branch 'ieee802154-for-davem-2019-01-31' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2019-01-31
An update from ieee802154 for your *net* tree.
I waited a while to see if anything else comes up, but it seems this time
we only have one fixup patch for the -rc rounds.
Colin fixed some indentation in the mcr20a drivers. That's about it.
If there are any problems with taking these two before the final 5.0 let
me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 31 Jan 2019 16:47:10 +0000 (08:47 -0800)]
rds: fix refcount bug in rds_sock_addref
syzbot was able to catch a bug in rds [1]
The issue here is that the socket might be found in a hash table
but that its refcount has already be set to 0 by another cpu.
We need to use refcount_inc_not_zero() to be safe here.
[1]
refcount_t: increment on 0; use-after-free.
WARNING: CPU: 1 PID: 23129 at lib/refcount.c:153 refcount_inc_checked lib/refcount.c:153 [inline]
WARNING: CPU: 1 PID: 23129 at lib/refcount.c:153 refcount_inc_checked+0x61/0x70 lib/refcount.c:151
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 23129 Comm: syz-executor3 Not tainted 5.0.0-rc4+ #53
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1db/0x2d0 lib/dump_stack.c:113
panic+0x2cb/0x65c kernel/panic.c:214
__warn.cold+0x20/0x48 kernel/panic.c:571
report_bug+0x263/0x2b0 lib/bug.c:186
fixup_bug arch/x86/kernel/traps.c:178 [inline]
fixup_bug arch/x86/kernel/traps.c:173 [inline]
do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:271
do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:290
invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:973
RIP: 0010:refcount_inc_checked lib/refcount.c:153 [inline]
RIP: 0010:refcount_inc_checked+0x61/0x70 lib/refcount.c:151
Code: 1d 51 63 c8 06 31 ff 89 de e8 eb 1b f2 fd 84 db 75 dd e8 a2 1a f2 fd 48 c7 c7 60 9f 81 88 c6 05 31 63 c8 06 01 e8 af 65 bb fd <0f> 0b eb c1 90 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 41 54 49
RSP: 0018:
ffff8880a0cbf1e8 EFLAGS:
00010282
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
ffffc90006113000
RDX:
000000000001047d RSI:
ffffffff81685776 RDI:
0000000000000005
RBP:
ffff8880a0cbf1f8 R08:
ffff888097c9e100 R09:
ffffed1015ce5021
R10:
ffffed1015ce5020 R11:
ffff8880ae728107 R12:
ffff8880723c20c0
R13:
ffff8880723c24b0 R14:
dffffc0000000000 R15:
ffffed1014197e64
sock_hold include/net/sock.h:647 [inline]
rds_sock_addref+0x19/0x20 net/rds/af_rds.c:675
rds_find_bound+0x97c/0x1080 net/rds/bind.c:82
rds_recv_incoming+0x3be/0x1430 net/rds/recv.c:362
rds_loop_xmit+0xf3/0x2a0 net/rds/loop.c:96
rds_send_xmit+0x1355/0x2a10 net/rds/send.c:355
rds_sendmsg+0x323c/0x44e0 net/rds/send.c:1368
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg+0xdd/0x130 net/socket.c:631
__sys_sendto+0x387/0x5f0 net/socket.c:1788
__do_sys_sendto net/socket.c:1800 [inline]
__se_sys_sendto net/socket.c:1796 [inline]
__x64_sys_sendto+0xe1/0x1a0 net/socket.c:1796
do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458089
Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007fc266df8c78 EFLAGS:
00000246 ORIG_RAX:
000000000000002c
RAX:
ffffffffffffffda RBX:
0000000000000006 RCX:
0000000000458089
RDX:
0000000000000000 RSI:
00000000204b3fff RDI:
0000000000000005
RBP:
000000000073bf00 R08:
00000000202b4000 R09:
0000000000000010
R10:
0000000000000000 R11:
0000000000000246 R12:
00007fc266df96d4
R13:
00000000004c56e4 R14:
00000000004d94a8 R15:
00000000ffffffff
Fixes: cc4dfb7f70a3 ("rds: fix two RCU related problems")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: rds-devel@oss.oracle.com
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bart Van Assche [Wed, 30 Jan 2019 18:42:30 +0000 (10:42 -0800)]
lib/test_rhashtable: Make test_insert_dup() allocate its hash table dynamically
The test_insert_dup() function from lib/test_rhashtable.c passes a
pointer to a stack object to rhltable_init(). Allocate the hash table
dynamically to avoid that the following is reported with object
debugging enabled:
ODEBUG: object (ptrval) is on stack (ptrval), but NOT annotated.
WARNING: CPU: 0 PID: 1 at lib/debugobjects.c:368 __debug_object_init+0x312/0x480
Modules linked in:
EIP: __debug_object_init+0x312/0x480
Call Trace:
? debug_object_init+0x1a/0x20
? __init_work+0x16/0x30
? rhashtable_init+0x1e1/0x460
? sched_clock_cpu+0x57/0xe0
? rhltable_init+0xb/0x20
? test_insert_dup+0x32/0x20f
? trace_hardirqs_on+0x38/0xf0
? ida_dump+0x10/0x10
? jhash+0x130/0x130
? my_hashfn+0x30/0x30
? test_rht_init+0x6aa/0xab4
? ida_dump+0x10/0x10
? test_rhltable+0xc5c/0xc5c
? do_one_initcall+0x67/0x28e
? trace_hardirqs_off+0x22/0xe0
? restore_all_kernel+0xf/0x70
? trace_hardirqs_on_thunk+0xc/0x10
? restore_all_kernel+0xf/0x70
? kernel_init_freeable+0x142/0x213
? rest_init+0x230/0x230
? kernel_init+0x10/0x110
? schedule_tail_wrapper+0x9/0xc
? ret_from_fork+0x19/0x24
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Wen [Thu, 31 Jan 2019 07:18:56 +0000 (15:18 +0800)]
l2tp: copy 4 more bytes to linear part if necessary
The size of L2TPv2 header with all optional fields is 14 bytes.
l2tp_udp_recv_core only moves 10 bytes to the linear part of a
skb. This may lead to l2tp_recv_common read data outside of a skb.
This patch make sure that there is at least 14 bytes in the linear
part of a skb to meet the maximum need of l2tp_udp_recv_core and
l2tp_recv_common. The minimum size of both PPP HDLC-like frame and
Ethernet frame is larger than 14 bytes, so we are safe to do so.
Also remove L2TP_HDR_SIZE_NOSEQ, it is unused now.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jacob Wen <jian.w.wen@oracle.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Norris [Tue, 29 Jan 2019 23:12:01 +0000 (15:12 -0800)]
ath10k: correct bus type for WCN3990
WCN3990 is SNOC, not PCI. This prevents probing WCN3990.
Fixes: 367c899f622c ("ath10k: add bus type check in ath10k_init_hw_params")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lorenzo Bianconi [Sun, 27 Jan 2019 11:15:49 +0000 (12:15 +0100)]
mt76x0: eeprom: fix chan_vs_power map in mt76x0_get_power_info
Report correct eeprom per channel power value.
Fix chan_vs_power map in mt76x0_get_power_info routine
Fixes: f2a2e819d672 ("mt76x0: remove eeprom dependency from mt76x0_get_power_info")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Colin Ian King [Mon, 14 Jan 2019 15:48:34 +0000 (15:48 +0000)]
ieee802154: mcr20a: fix indentation, remove tabs
The are a couple of statments that are one level too deep, fix this by
removing tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Thomas Lendacky [Thu, 31 Jan 2019 14:33:06 +0000 (14:33 +0000)]
x86/microcode/amd: Don't falsely trick the late loading mechanism
The load_microcode_amd() function searches for microcode patches and
attempts to apply a microcode patch if it is of different level than the
currently installed level.
While the processor won't actually load a level that is less than
what is already installed, the logic wrongly returns UCODE_NEW thus
signaling to its caller reload_store() that a late loading should be
attempted.
If the file-system contains an older microcode revision than what is
currently running, such a late microcode reload can result in these
misleading messages:
x86/CPU: CPU features have changed after loading microcode, but might not take effect.
x86/CPU: Please consider either early loading through initrd/built-in or a potential BIOS update.
These messages were issued on a system where SME/SEV are not
enabled by the BIOS (MSR C001_0010[23] = 0b) because during boot,
early_detect_mem_encrypt() is called and cleared the SME and SEV
features in this case.
However, after the wrong late load attempt, get_cpu_cap() is called and
reloads the SME and SEV feature bits, resulting in the messages.
Update the microcode level check to not attempt microcode loading if the
current level is greater than(!) and not only equal to the current patch
level.
[ bp: massage commit message. ]
Fixes: 2613f36ed965 ("x86/microcode: Attempt late loading only when new microcode is present")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/154894518427.9406.8246222496874202773.stgit@tlendack-t1.amdoffice.net
Jens Axboe [Wed, 30 Jan 2019 15:41:40 +0000 (08:41 -0700)]
ide: ensure atapi sense request aren't preempted
There's an issue with how sense requests are handled in IDE. If ide-cd
encounters an error, it queues a sense request. With how IDE request
handling is done, this is the next request we need to handle. But it's
impossible to guarantee this, as another request could come in between
the sense being queued, and ->queue_rq() being run and handling it. If
that request ALSO fails, then we attempt to doubly queue the single
sense request we have.
Since we only support one active request at the time, defer request
processing when a sense request is queued.
Fixes: 600335205b8d "ide: convert to blk-mq"
Reported-by: He Zhe <zhe.he@windriver.com>
Tested-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Nicolas Saenz Julienne [Sat, 26 Jan 2019 16:38:29 +0000 (10:38 -0600)]
fpga: stratix10-soc: fix wrong of_node_put() in init function
After finding a "firmware" dt node stratix10 tries to match it's
compatible string with it. To do so it's calling of_find_matching_node()
which already takes care of decreasing the refcount on the "firmware"
node. We are then incorrectly decreasing the refcount on that node
again.
This patch removes the unwarranted call to of_node_put().
Fixes: e7eef1d7633a ("fpga: add intel stratix10 soc fpga manager driver")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Alan Tull <atull@kernel.org>
Acked-by: Moritz Fischer <mdf@kernel.org>
[atull: remove unnecessary braces]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 23 Jan 2019 13:48:54 +0000 (14:48 +0100)]
blk-mq: protect debugfs_create_files() from failures
If debugfs were to return a non-NULL error for a debugfs call, using
that pointer later in debugfs_create_files() would crash.
Fix that by properly checking the pointer before referencing it.
Reported-by: Michal Hocko <mhocko@kernel.org>
Reported-and-tested-by: syzbot+b382ba6a802a3d242790@syzkaller.appspotmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve French [Tue, 29 Jan 2019 23:27:33 +0000 (17:27 -0600)]
cifs: update internal module version number
To 2.17
Signed-off-by: Steve French <stfrench@microsoft.com>
Aurelien Aptel [Thu, 31 Jan 2019 12:46:07 +0000 (13:46 +0100)]
CIFS: fix use-after-free of the lease keys
The request buffers are freed right before copying the pointers.
Use the func args instead which are identical and still valid.
Simple reproducer (requires KASAN enabled) on a cifs mount:
echo foo > foo ; tail -f foo & rm foo
Cc: <stable@vger.kernel.org> # 4.20
Fixes: 179e44d49c2f ("smb3: add tracepoint for sending lease break responses to server")
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Paulo Alcantara <palcantara@suse.de>
Greg Kroah-Hartman [Thu, 31 Jan 2019 12:57:58 +0000 (13:57 +0100)]
relay: check return of create_buf_file() properly
If create_buf_file() returns an error, don't try to reference it later
as a valid dentry pointer.
This problem was exposed when debugfs started to return errors instead
of just NULL for some calls when they do not succeed properly.
Also, the check for WARN_ON(dentry) was just wrong :)
Reported-by: Kees Cook <keescook@chromium.org>
Reported-and-tested-by: syzbot+16c3a70e1e9b29346c43@syzkaller.appspotmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Fixes: ff9fb72bc077 ("debugfs: return error values, not NULL")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeremy Soller [Wed, 30 Jan 2019 23:12:31 +0000 (16:12 -0700)]
ALSA: hda/realtek - Headset microphone support for System76 darp5
On the System76 Darter Pro (darp5), there is a headset microphone
input attached to 0x1a that does not have a jack detect. In order to
get it working, the pin configuration needs to be set correctly, and
the ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC fixup needs to be applied.
This is similar to the MIC_NO_PRESENCE fixups for some Dell laptops,
except we have a separate microphone jack that is already configured
correctly.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kyle Tso [Wed, 30 Jan 2019 03:13:53 +0000 (11:13 +0800)]
usb: typec: tcpm: Correct the PPS out_volt calculation
When Sink negotiates PPS, the voltage range of selected PPS APDO might
not cover the previous voltage (out_volt). If the previous out_volt is
lower than the new min_volt, the output voltage in RDO might be set to
an invalid value. For instance, supposed that the previous voltage is
5V, and the new voltage range in the APDO is 7V-12V. Then the output
voltage in the RDO should not be set to 5V which is lower than the
possible min_volt 7V.
Fix this by choosing the maximal value between the previous voltage and
the new min_volt first. And ensure that this value will not exceed the
new max_volt. The new out_volt will fall within the new voltage range
while being the closest value compared to the previous out_volt.
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: c710d0bb76ff0 ("usb: typec: tcpm: Extend the matching rules on PPS APDO selection")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 31 Jan 2019 07:57:51 +0000 (08:57 +0100)]
Merge tag 'fixes-for-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v5.0-rc4
Dwc3 got a fix for cases when gadget driver queue an OUT request of
length 0; this is a case that has been overlooked for quite some time
now.
Exynos' dwc3 glue layer got a fix on the error path for those cases
where clk_prepare_enable() fails.
TI's AM335x PHY driver got a fix for a race condition during
probe. This race happened because driver was powering off the PHY only
after adding the PHY handle to the framework. The result is that we
could fall into a situation where user of the PHY (MUSB) could call
phy_init() before phy driver's probe() called phy_poweroff() which
would result in a powered off PHY after phy_init() was called.
The old net2272 driver got a fix for an erroneous use of bitwise
negation.
* tag 'fixes-for-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: phy: am335x: fix race condition in _probe
usb: dwc3: exynos: Fix error handling of clk_prepare_enable
usb: phy: fix link errors
usb: gadget: udc: net2272: Fix bitwise and boolean operations
usb: dwc3: gadget: Handle 0 xfer length for OUT EP
David S. Miller [Thu, 31 Jan 2019 06:24:49 +0000 (22:24 -0800)]
Merge branch 'stmmac-fixes'
Jose Abreu says:
====================
net: stmmac: Misc fixes
Some misc fixes for stmmac targeting -net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 30 Jan 2019 14:54:21 +0000 (15:54 +0100)]
net: stmmac: Disable EEE mode earlier in XMIT callback
In stmmac xmit callback we use a different flow for TSO packets but TSO
xmit callback is not disabling the EEE mode.
Fix this by disabling earlier the EEE mode, i.e. before calling the TSO
xmit callback.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 30 Jan 2019 14:54:20 +0000 (15:54 +0100)]
net: stmmac: Send TSO packets always from Queue 0
The number of TSO enabled channels in HW can be different than the
number of total channels. There is no way to determined, at runtime, the
number of TSO capable channels and its safe to assume that if TSO is
enabled then at least channel 0 will be TSO capable.
Lets always send TSO packets from Queue 0.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 30 Jan 2019 14:54:19 +0000 (15:54 +0100)]
net: stmmac: Fallback to Platform Data clock in Watchdog conversion
If we don't have DT then stmmac_clk will not be available. Let's add a
new Platform Data field so that we can specify the refclk by this mean.
This way we can still use the coalesce command in PCI based setups.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 30 Jan 2019 11:49:48 +0000 (12:49 +0100)]
ipvlan, l3mdev: fix broken l3s mode wrt local routes
While implementing ipvlan l3 and l3s mode for kubernetes CNI plugin,
I ran into the issue that while l3 mode is working fine, l3s mode
does not have any connectivity to kube-apiserver and hence all pods
end up in Error state as well. The ipvlan master device sits on
top of a bond device and hostns traffic to kube-apiserver (also running
in hostns) is DNATed from 10.152.183.1:443 to 139.178.29.207:37573
where the latter is the address of the bond0. While in l3 mode, a
curl to https://10.152.183.1:443 or to https://139.178.29.207:37573
works fine from hostns, neither of them do in case of l3s. In the
latter only a curl to https://127.0.0.1:37573 appeared to work where
for local addresses of bond0 I saw kernel suddenly starting to emit
ARP requests to query HW address of bond0 which remained unanswered
and neighbor entries in INCOMPLETE state. These ARP requests only
happen while in l3s.
Debugging this further, I found the issue is that l3s mode is piggy-
backing on l3 master device, and in this case local routes are using
l3mdev_master_dev_rcu(dev) instead of net->loopback_dev as per commit
f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev
if relevant") and
5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be
a loopback"). I found that reverting them back into using the
net->loopback_dev fixed ipvlan l3s connectivity and got everything
working for the CNI.
Now judging from
4fbae7d83c98 ("ipvlan: Introduce l3s mode") and the
l3mdev paper in [0] the only sole reason why ipvlan l3s is relying
on l3 master device is to get the l3mdev_ip_rcv() receive hook for
setting the dst entry of the input route without adding its own
ipvlan specific hacks into the receive path, however, any l3 domain
semantics beyond just that are breaking l3s operation. Note that
ipvlan also has the ability to dynamically switch its internal
operation from l3 to l3s for all ports via ipvlan_set_port_mode()
at runtime. In any case, l3 vs l3s soley distinguishes itself by
'de-confusing' netfilter through switching skb->dev to ipvlan slave
device late in NF_INET_LOCAL_IN before handing the skb to L4.
Minimal fix taken here is to add a IFF_L3MDEV_RX_HANDLER flag which,
if set from ipvlan setup, gets us only the wanted l3mdev_l3_rcv() hook
without any additional l3mdev semantics on top. This should also have
minimal impact since dev->priv_flags is already hot in cache. With
this set, l3s mode is working fine and I also get things like
masquerading pod traffic on the ipvlan master properly working.
[0] https://netdevconf.org/1.2/papers/ahern-what-is-l3mdev-paper.pdf
Fixes: f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev if relevant")
Fixes: 5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be a loopback")
Fixes: 4fbae7d83c98 ("ipvlan: Introduce l3s mode")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Martynas Pumputis <m@lambda.lt>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Wen [Wed, 30 Jan 2019 06:55:14 +0000 (14:55 +0800)]
l2tp: fix reading optional fields of L2TPv3
Use pskb_may_pull() to make sure the optional fields are in skb linear
parts, so we can safely read them later.
It's easy to reproduce the issue with a net driver that supports paged
skb data. Just create a L2TPv3 over IP tunnel and then generates some
network traffic.
Once reproduced, rx err in /sys/kernel/debug/l2tp/tunnels will increase.
Changes in v4:
1. s/l2tp_v3_pull_opt/l2tp_v3_ensure_opt_in_linear/
2. s/tunnel->version != L2TP_HDR_VER_2/tunnel->version == L2TP_HDR_VER_3/
3. Add 'Fixes' in commit messages.
Changes in v3:
1. To keep consistency, move the code out of l2tp_recv_common.
2. Use "net" instead of "net-next", since this is a bug fix.
Changes in v2:
1. Only fix L2TPv3 to make code simple.
To fix both L2TPv3 and L2TPv2, we'd better refactor l2tp_recv_common.
It's complicated to do so.
2. Reloading pointers after pskb_may_pull
Fixes: f7faffa3ff8e ("l2tp: Add L2TPv3 protocol support")
Fixes: 0d76751fad77 ("l2tp: Add L2TPv3 IP encapsulation (no UDP) support")
Fixes: a32e0eec7042 ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6")
Signed-off-by: Jacob Wen <jian.w.wen@oracle.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
George Amanakis [Wed, 30 Jan 2019 03:50:13 +0000 (22:50 -0500)]
tun: move the call to tun_set_real_num_queues
Call tun_set_real_num_queues() after the increment of tun->numqueues
since the former depends on it. Otherwise, the number of queues is not
correctly accounted for, which results to warnings similar to:
"vnet0 selects TX queue 11, but real number of TX queues is 11".
Fixes: 0b7959b62573 ("tun: publish tfile after it's fully initialized")
Reported-and-tested-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yohei Kanemaru [Tue, 29 Jan 2019 06:52:34 +0000 (15:52 +0900)]
ipv6: sr: clear IP6CB(skb) on SRH ip4ip6 encapsulation
skb->cb may contain data from previous layers (in an observed case
IPv4 with L3 Master Device). In the observed scenario, the data in
IPCB(skb)->frags was misinterpreted as IP6CB(skb)->frag_max_size,
eventually caused an unexpected IPv6 fragmentation in ip6_fragment()
through ip6_finish_output().
This patch clears IP6CB(skb), which potentially contains garbage data,
on the SRH ip4ip6 encapsulation.
Fixes: 32d99d0b6702 ("ipv6: sr: add support for ip4ip6 encapsulation")
Signed-off-by: Yohei Kanemaru <yohei.kanemaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 30 Jan 2019 22:02:43 +0000 (14:02 -0800)]
Merge branch 'virtio_net-Fix-problems-around-XDP-tx-and-napi_tx'
Toshiaki Makita says:
====================
virtio_net: Fix problems around XDP tx and napi_tx
While I'm looking into how to account standard tx counters on XDP tx
processing, I found several bugs around XDP tx and napi_tx.
Patch1: Fix oops on error path. Patch2 depends on this.
Patch2: Fix memory corruption on freeing xdp_frames with napi_tx enabled.
Patch3: Minor fix patch5 depends on.
Patch4: Fix memory corruption on processing xdp_frames when XDP is disabled.
Also patch5 depends on this.
Patch5: Fix memory corruption on processing xdp_frames while XDP is being
disabled.
Patch6: Minor fix patch7 depends on.
Patch7: Fix memory corruption on freeing sk_buff or xdp_frames when a normal
queue is reused for XDP and vise versa.
v2:
- patch5: Make rcu_assign_pointer/synchronize_net conditional instead of
_virtnet_set_queues.
- patch7: Use napi_consume_skb() instead of dev_consume_skb_any()
====================
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Tue, 29 Jan 2019 00:45:59 +0000 (09:45 +0900)]
virtio_net: Differentiate sk_buff and xdp_frame on freeing
We do not reset or free up unused buffers when enabling/disabling XDP,
so it can happen that xdp_frames are freed after disabling XDP or
sk_buffs are freed after enabling XDP on xdp tx queues.
Thus we need to handle both forms (xdp_frames and sk_buffs) regardless
of XDP setting.
One way to trigger this problem is to disable XDP when napi_tx is
enabled. In that case, virtnet_xdp_set() calls virtnet_napi_enable()
which kicks NAPI. The NAPI handler will call virtnet_poll_cleantx()
which invokes free_old_xmit_skbs() for queues which have been used by
XDP.
Note that even with this change we need to keep skipping
free_old_xmit_skbs() from NAPI handlers when XDP is enabled, because XDP
tx queues do not aquire queue locks.
- v2: Use napi_consume_skb() instead of dev_consume_skb_any()
Fixes: 4941d472bf95 ("virtio-net: do not reset during XDP set")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Tue, 29 Jan 2019 00:45:58 +0000 (09:45 +0900)]
virtio_net: Use xdp_return_frame to free xdp_frames on destroying vqs
put_page() can work as a fallback for freeing xdp_frames, but the
appropriate way is to use xdp_return_frame().
Fixes: cac320c850ef ("virtio_net: convert to use generic xdp_frame and xdp_return_frame API")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Tue, 29 Jan 2019 00:45:57 +0000 (09:45 +0900)]
virtio_net: Don't process redirected XDP frames when XDP is disabled
Commit
8dcc5b0ab0ec ("virtio_net: fix ndo_xdp_xmit crash towards dev not
ready for XDP") tried to avoid access to unexpected sq while XDP is
disabled, but was not complete.
There was a small window which causes out of bounds sq access in
virtnet_xdp_xmit() while disabling XDP.
An example case of
- curr_queue_pairs = 6 (2 for SKB and 4 for XDP)
- online_cpu_num = xdp_queue_paris = 4
when XDP is enabled:
CPU 0 CPU 1
(Disabling XDP) (Processing redirected XDP frames)
virtnet_xdp_xmit()
virtnet_xdp_set()
_virtnet_set_queues()
set curr_queue_pairs (2)
check if rq->xdp_prog is not NULL
virtnet_xdp_sq(vi)
qp = curr_queue_pairs -
xdp_queue_pairs +
smp_processor_id()
= 2 - 4 + 1 = -1
sq = &vi->sq[qp] // out of bounds access
set xdp_queue_pairs (0)
rq->xdp_prog = NULL
Basically we should not change curr_queue_pairs and xdp_queue_pairs
while someone can read the values. Thus, when disabling XDP, assign NULL
to rq->xdp_prog first, and wait for RCU grace period, then change
xxx_queue_pairs.
Note that we need to keep the current order when enabling XDP though.
- v2: Make rcu_assign_pointer/synchronize_net conditional instead of
_virtnet_set_queues.
Fixes: 186b3c998c50 ("virtio-net: support XDP_REDIRECT")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Tue, 29 Jan 2019 00:45:56 +0000 (09:45 +0900)]
virtio_net: Fix out of bounds access of sq
When XDP is disabled, curr_queue_pairs + smp_processor_id() can be
larger than max_queue_pairs.
There is no guarantee that we have enough XDP send queues dedicated for
each cpu when XDP is disabled, so do not count drops on sq in that case.
Fixes: 5b8f3c8d30a6 ("virtio_net: Add XDP related stats")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Tue, 29 Jan 2019 00:45:55 +0000 (09:45 +0900)]
virtio_net: Fix not restoring real_num_rx_queues
When _virtnet_set_queues() failed we did not restore real_num_rx_queues.
Fix this by placing the change of real_num_rx_queues after
_virtnet_set_queues().
This order is also in line with virtnet_set_channels().
Fixes: 4941d472bf95 ("virtio-net: do not reset during XDP set")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Tue, 29 Jan 2019 00:45:54 +0000 (09:45 +0900)]
virtio_net: Don't call free_old_xmit_skbs for xdp_frames
When napi_tx is enabled, virtnet_poll_cleantx() called
free_old_xmit_skbs() even for xdp send queue.
This is bogus since the queue has xdp_frames, not sk_buffs, thus mangled
device tx bytes counters because skb->len is meaningless value, and even
triggered oops due to general protection fault on freeing them.
Since xdp send queues do not aquire locks, old xdp_frames should be
freed only in virtnet_xdp_xmit(), so just skip free_old_xmit_skbs() for
xdp send queues.
Similarly virtnet_poll_tx() called free_old_xmit_skbs(). This NAPI
handler is called even without calling start_xmit() because cb for tx is
by default enabled. Once the handler is called, it enabled the cb again,
and then the handler would be called again. We don't need this handler
for XDP, so don't enable cb as well as not calling free_old_xmit_skbs().
Also, we need to disable tx NAPI when disabling XDP, so
virtnet_poll_tx() can safely access curr_queue_pairs and
xdp_queue_pairs, which are not atomically updated while disabling XDP.
Fixes: b92f1e6751a6 ("virtio-net: transmit napi")
Fixes: 7b0411ef4aa6 ("virtio-net: clean tx descriptors from rx napi")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Tue, 29 Jan 2019 00:45:53 +0000 (09:45 +0900)]
virtio_net: Don't enable NAPI when interface is down
Commit
4e09ff536284 ("virtio-net: disable NAPI only when enabled during
XDP set") tried to fix inappropriate NAPI enabling/disabling when
!netif_running(), but was not complete.
On error path virtio_net could enable NAPI even when !netif_running().
This can cause enabling NAPI twice on virtnet_open(), which would
trigger BUG_ON() in napi_enable().
Fixes: 4941d472bf95b ("virtio-net: do not reset during XDP set")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 30 Jan 2019 22:00:02 +0000 (14:00 -0800)]
Merge branch 'erspan-always-reports-output-key-to-userspace'
Lorenzo Bianconi says:
====================
erspan: always reports output key to userspace
Erspan protocol relies on output key to set session id header field.
However TUNNEL_KEY bit is cleared in order to not add key field to
the external GRE header and so the configured o_key is not reported
to userspace.
Fix the issue adding TUNNEL_KEY bit to the o_flags parameter dumping
device info
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Mon, 28 Jan 2019 21:23:49 +0000 (22:23 +0100)]
net: ip6_gre: always reports o_key to userspace
As Erspan_v4, Erspan_v6 protocol relies on o_key to configure
session id header field. However TUNNEL_KEY bit is cleared in
ip6erspan_tunnel_xmit since ERSPAN protocol does not set the key field
of the external GRE header and so the configured o_key is not reported
to userspace. The issue can be triggered with the following reproducer:
$ip link add ip6erspan1 type ip6erspan local 2000::1 remote 2000::2 \
key 1 seq erspan_ver 1
$ip link set ip6erspan1 up
ip -d link sh ip6erspan1
ip6erspan1@NONE: <BROADCAST,MULTICAST> mtu 1422 qdisc noop state DOWN mode DEFAULT
link/ether ba:ff:09:24:c3:0e brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500
ip6erspan remote 2000::2 local 2000::1 encaplimit 4 flowlabel 0x00000 ikey 0.0.0.1 iseq oseq
Fix the issue adding TUNNEL_KEY bit to the o_flags parameter in
ip6gre_fill_info
Fixes: 5a963eb61b7c ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Mon, 28 Jan 2019 21:23:48 +0000 (22:23 +0100)]
net: ip_gre: always reports o_key to userspace
Erspan protocol (version 1 and 2) relies on o_key to configure
session id header field. However TUNNEL_KEY bit is cleared in
erspan_xmit since ERSPAN protocol does not set the key field
of the external GRE header and so the configured o_key is not reported
to userspace. The issue can be triggered with the following reproducer:
$ip link add erspan1 type erspan local 192.168.0.1 remote 192.168.0.2 \
key 1 seq erspan_ver 1
$ip link set erspan1 up
$ip -d link sh erspan1
erspan1@NONE: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1450 qdisc pfifo_fast state UNKNOWN mode DEFAULT
link/ether 52:aa:99:95:9a:b5 brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500
erspan remote 192.168.0.2 local 192.168.0.1 ttl inherit ikey 0.0.0.1 iseq oseq erspan_index 0
Fix the issue adding TUNNEL_KEY bit to the o_flags parameter in
ipgre_fill_info
Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Smythies [Wed, 30 Jan 2019 16:28:22 +0000 (08:28 -0800)]
cpuidle: poll_state: Fix default time limit
The default time is declared in units of microsecnds,
but is used as nanoseconds, resulting in significant
accounting errors for idle state 0 time when all idle
states deeper than 0 are disabled.
Under these unusual conditions, we don't really care
about the poll time limit anyhow.
Fixes: 800fb34a99ce ("cpuidle: poll_state: Disregard disable idle states")
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Vincent Guittot [Wed, 30 Jan 2019 17:26:02 +0000 (18:26 +0100)]
PM-runtime: Fix deadlock with ktime_get()
A deadlock has been seen when swicthing clocksources which use
PM-runtime. The call path is:
change_clocksource
...
write_seqcount_begin
...
timekeeping_update
...
sh_cmt_clocksource_enable
...
rpm_resume
pm_runtime_mark_last_busy
ktime_get
do
read_seqcount_begin
while read_seqcount_retry
....
write_seqcount_end
Although we should be safe because we haven't yet changed the
clocksource at that time, we can't do that because of seqcount
protection.
Use ktime_get_mono_fast_ns() instead which is lock safe for such
cases.
With ktime_get_mono_fast_ns, the timestamp is not guaranteed to be
monotonic across an update and as a result can goes backward.
According to update_fast_timekeeper() description: "In the worst
case, this can result is a slightly wrong timestamp (a few
nanoseconds)". For PM-runtime autosuspend, this means only that
the suspend decision may be slightly suboptimal.
Fixes: 8234f6734c5d ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Waiman Long [Wed, 30 Jan 2019 18:52:38 +0000 (13:52 -0500)]
fs/dcache: Track & report number of negative dentries
The current dentry number tracking code doesn't distinguish between
positive & negative dentries. It just reports the total number of
dentries in the LRU lists.
As excessive number of negative dentries can have an impact on system
performance, it will be wise to track the number of positive and
negative dentries separately.
This patch adds tracking for the total number of negative dentries in
the system LRU lists and reports it in the 5th field in the
/proc/sys/fs/dentry-state file. The number, however, does not include
negative dentries that are in flight but not in the LRU yet as well as
those in the shrinker lists which are on the way out anyway.
The number of positive dentries in the LRU lists can be roughly found by
subtracting the number of negative dentries from the unused count.
Matthew Wilcox had confirmed that since the introduction of the
dentry_stat structure in 2.1.60, the dummy array was there, probably for
future extension. They were not replacements of pre-existing fields.
So no sane applications that read the value of /proc/sys/fs/dentry-state
will do dummy thing if the last 2 fields of the sysctl parameter are not
zero. IOW, it will be safe to use one of the dummy array entry for
negative dentry count.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Waiman Long [Wed, 30 Jan 2019 18:52:37 +0000 (13:52 -0500)]
fs: Don't need to put list_lru into its own cacheline
The list_lru structure is essentially just a pointer to a table of
per-node LRU lists. Even if CONFIG_MEMCG_KMEM is defined, the list
field is just used for LRU list registration and shrinker_id is set at
initialization. Those fields won't need to be touched that often.
So there is no point to make the list_lru structures to sit in their own
cachelines.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Waiman Long [Wed, 30 Jan 2019 18:52:36 +0000 (13:52 -0500)]
fs/dcache: Fix incorrect nr_dentry_unused accounting in shrink_dcache_sb()
The nr_dentry_unused per-cpu counter tracks dentries in both the LRU
lists and the shrink lists where the DCACHE_LRU_LIST bit is set.
The shrink_dcache_sb() function moves dentries from the LRU list to a
shrink list and subtracts the dentry count from nr_dentry_unused. This
is incorrect as the nr_dentry_unused count will also be decremented in
shrink_dentry_list() via d_shrink_del().
To fix this double decrement, the decrement in the shrink_dcache_sb()
function is taken out.
Fixes: 4e717f5c1083 ("list_lru: remove special case function list_lru_dispose_all."
Cc: stable@kernel.org
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mathias Thore [Mon, 28 Jan 2019 09:07:47 +0000 (10:07 +0100)]
ucc_geth: Reset BQL queue when stopping device
After a timeout event caused by for example a broadcast storm, when
the MAC and PHY are reset, the BQL TX queue needs to be reset as
well. Otherwise, the device will exhibit severe performance issues
even after the storm has ended.
Co-authored-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: Mathias Thore <mathias.thore@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josh Poimboeuf [Wed, 30 Jan 2019 13:13:58 +0000 (07:13 -0600)]
cpu/hotplug: Fix "SMT disabled by BIOS" detection for KVM
With the following commit:
73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
... the hotplug code attempted to detect when SMT was disabled by BIOS,
in which case it reported SMT as permanently disabled. However, that
code broke a virt hotplug scenario, where the guest is booted with only
primary CPU threads, and a sibling is brought online later.
The problem is that there doesn't seem to be a way to reliably
distinguish between the HW "SMT disabled by BIOS" case and the virt
"sibling not yet brought online" case. So the above-mentioned commit
was a bit misguided, as it permanently disabled SMT for both cases,
preventing future virt sibling hotplugs.
Going back and reviewing the original problems which were attempted to
be solved by that commit, when SMT was disabled in BIOS:
1) /sys/devices/system/cpu/smt/control showed "on" instead of
"notsupported"; and
2) vmx_vm_init() was incorrectly showing the L1TF_MSG_SMT warning.
I'd propose that we instead consider #1 above to not actually be a
problem. Because, at least in the virt case, it's possible that SMT
wasn't disabled by BIOS and a sibling thread could be brought online
later. So it makes sense to just always default the smt control to "on"
to allow for that possibility (assuming cpuid indicates that the CPU
supports SMT).
The real problem is #2, which has a simple fix: change vmx_vm_init() to
query the actual current SMT state -- i.e., whether any siblings are
currently online -- instead of looking at the SMT "control" sysfs value.
So fix it by:
a) reverting the original "fix" and its followup fix:
73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
bc2d8d262cba ("cpu/hotplug: Fix SMT supported evaluation")
and
b) changing vmx_vm_init() to query the actual current SMT state --
instead of the sysfs control value -- to determine whether the L1TF
warning is needed. This also requires the 'sched_smt_present'
variable to exported, instead of 'cpu_smt_control'.
Fixes: 73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joe Mario <jmario@redhat.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/e3a85d585da28cc333ecbc1e78ee9216e6da9396.1548794349.git.jpoimboe@redhat.com
David S. Miller [Wed, 30 Jan 2019 18:19:31 +0000 (10:19 -0800)]
Merge branch 'net-various-compat-ioctl-fixes'
Johannes Berg says:
====================
various compat ioctl fixes
Back a long time ago, I already fixed a few of these by passing
the size of the struct ifreq to do_sock_ioctl(). However, Robert
found more cases, and now it won't be as simple because we'd have
to pass that down all the way to e.g. bond_do_ioctl() which isn't
really feasible.
Therefore, restore the old code.
While looking at why SIOCGIFNAME was broken, I realized that Al
had removed that case - which had been handled in an explicit
separate function - as well, and looking through his work at the
time I saw that bond ioctls were also affected by the erroneous
removal.
I've restored SIOCGIFNAME and bond ioctls by going through the
(now renamed) dev_ifsioc() instead of reintroducing their own
helper functions, which I hope is correct but have only tested
with SIOCGIFNAME.
====================
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 25 Jan 2019 21:43:20 +0000 (22:43 +0100)]
net: socket: make bond ioctls go through compat_ifreq_ioctl()
Same story as before, these use struct ifreq and thus need
to be read with the shorter version to not cause faults.
Cc: stable@vger.kernel.org
Fixes: f92d4fc95341 ("kill bond_ioctl()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 25 Jan 2019 21:43:19 +0000 (22:43 +0100)]
net: socket: fix SIOCGIFNAME in compat
As reported by Robert O'Callahan in
https://bugzilla.kernel.org/show_bug.cgi?id=202273
reverting the previous changes in this area broke
the SIOCGIFNAME ioctl in compat again (I'd previously
fixed it after his previous report of breakage in
https://bugzilla.kernel.org/show_bug.cgi?id=199469).
This is obviously because I fixed SIOCGIFNAME more or
less by accident.
Fix it explicitly now by making it pass through the
restored compat translation code.
Cc: stable@vger.kernel.org
Fixes: 4cf808e7ac32 ("kill dev_ifname32()")
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 25 Jan 2019 21:43:18 +0000 (22:43 +0100)]
Revert "kill dev_ifsioc()"
This reverts commit
bf4405737f9f ("kill dev_ifsioc()").
This wasn't really unused as implied by the original commit,
it still handles the copy to/from user differently, and the
commit thus caused issues such as
https://bugzilla.kernel.org/show_bug.cgi?id=199469
and
https://bugzilla.kernel.org/show_bug.cgi?id=202273
However, deviating from a strict revert, rename dev_ifsioc()
to compat_ifreq_ioctl() to be clearer as to its purpose and
add a comment.
Cc: stable@vger.kernel.org
Fixes: bf4405737f9f ("kill dev_ifsioc()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 25 Jan 2019 21:43:17 +0000 (22:43 +0100)]
Revert "socket: fix struct ifreq size in compat ioctl"
This reverts commit
1cebf8f143c2 ("socket: fix struct ifreq
size in compat ioctl"), it's a bugfix for another commit that
I'll revert next.
This is not a 'perfect' revert, I'm keeping some coding style
intact rather than revert to the state with indentation errors.
Cc: stable@vger.kernel.org
Fixes: 1cebf8f143c2 ("socket: fix struct ifreq size in compat ioctl")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Wed, 30 Jan 2019 18:17:53 +0000 (19:17 +0100)]
Revert "staging: erofs: keep corrupted fs from crashing kernel in erofs_namei()"
This reverts commit
d4104c5e783f5d053b97268fb92001d785de7dd5.
Turns out it still needs some more work, I merged it to soon :(
Reported-by: Gao Xiang <gaoxiang25@huawei.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Wilson [Wed, 30 Jan 2019 10:55:17 +0000 (10:55 +0000)]
drm/amdgpu: Transfer fences to dmabuf importer
amdgpu only uses shared-fences internally, but dmabuf importers rely on
implicit write hazard tracking via the reservation_object.fence_excl.
For example, the importer use the write hazard for timing a page flip to
only occur after the exporter has finished flushing its write into the
surface. As such, on exporting a dmabuf, we must either flush all
outstanding fences (for we do not know which are writes and should have
been exclusive) or alternatively create a new exclusive fence that is
the composite of all the existing shared fences, and so will only be
signaled when all earlier fences are signaled (ensuring that we can not
be signaled before the completion of any earlier write).
v2: reservation_object is already locked by amdgpu_bo_reserve()
v3: Replace looping with get_fences_rcu and special case the promotion
of a single shared fence directly to an exclusive fence, bypassing the
fence array.
v4: Drop the fence array ref after assigning to reservation_object
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107341
Testcase: igt/amd_prime/amd-to-i915
References:
8e94a46c1770 ("drm/amdgpu: Attach exclusive fence to prime exported bo's. (v5)")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: "Christian König" <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Wed, 30 Jan 2019 17:30:03 +0000 (09:30 -0800)]
Merge tag 'iommu-fixes-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"A few more fixes this time:
- Two patches to fix the error path of the map_sg implementation of
the AMD IOMMU driver.
- Also a missing IOTLB flush is fixed in the AMD IOMMU driver.
- Memory leak fix for the Intel IOMMU driver.
- Fix a regression in the Mediatek IOMMU driver which caused device
initialization to fail (seen as broken HDMI output)"
* tag 'iommu-fixes-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix IOMMU page flush when detach device from a domain
iommu/mediatek: Use correct fwspec in mtk_iommu_add_device()
iommu/vt-d: Fix memory leak in intel_iommu_put_resv_regions()
iommu/amd: Unmap all mapped pages in error path of map_sg
iommu/amd: Call free_iova_fast with pfn in map_sg
Linus Torvalds [Wed, 30 Jan 2019 17:23:21 +0000 (09:23 -0800)]
Merge tag 'gpio-v5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a bunch of GPIO fixes for the v5.0 series. I was helped out by
Bartosz in collecting these fixes, for which I am very grateful, the
biggest achievement in GPIO right now is work distribution.
There is one serious core fix (timestamping) and a bunch of driver
fixes:
- Fix timestamps on nested IRQs
- Handle IRQs properly in multiple instances of PCF857x
- Use the right data register and IRQ type setting in the Spreadtrum
GPIO driver
- Let the value argument work properly when setting direction in the
Altera GPIO driver
- Mask interrupts properly in the vf610 driver"
* tag 'gpio-v5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: vf610: Mask all GPIO interrupts
gpio: altera-a10sr: Set proper output level for direction_output
gpio: sprd: Fix incorrect irq type setting for the async EIC
gpio: sprd: Fix the incorrect data register
gpiolib: fix line event timestamps for nested irqs
gpio: pcf857x: Fix interrupts on multiple instances
Eric W. Biederman [Wed, 30 Jan 2019 13:54:12 +0000 (07:54 -0600)]
btrfs: On error always free subvol_name in btrfs_mount
The subvol_name is allocated in btrfs_parse_subvol_options and is
consumed and freed in mount_subvol. Add a free to the error paths that
don't call mount_subvol so that it is guaranteed that subvol_name is
freed when an error happens.
Fixes: 312c89fbca06 ("btrfs: cleanup btrfs_mount() using btrfs_mount_root()")
Cc: stable@vger.kernel.org # v4.19+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Wed, 23 Jan 2019 16:09:16 +0000 (17:09 +0100)]
btrfs: clean up pending block groups when transaction commit aborts
The fstests generic/475 stresses transaction aborts and can reveal
space accounting or use-after-free bugs regarding block goups.
In this case the pending block groups that remain linked to the
structures after transaction commit aborts in the middle.
The corrupted slabs lead to failures in following tests, eg. generic/476
[ 8172.752887] BUG: unable to handle kernel NULL pointer dereference at
0000000000000058
[ 8172.755799] #PF error: [normal kernel read fault]
[ 8172.757571] PGD
661ae067 P4D
661ae067 PUD
3db8e067 PMD 0
[ 8172.759000] Oops: 0000 [#1] PREEMPT SMP
[ 8172.760209] CPU: 0 PID: 39 Comm: kswapd0 Tainted: G W 5.0.0-rc2-default #408
[ 8172.762495] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.11.2-0-gf9626cc-prebuilt.qemu-project.org 04/01/2014
[ 8172.765772] RIP: 0010:shrink_page_list+0x2f9/0xe90
[ 8172.770453] RSP: 0018:
ffff967f00663b18 EFLAGS:
00010287
[ 8172.771184] RAX:
0000000000000000 RBX:
ffff967f00663c20 RCX:
0000000000000000
[ 8172.772850] RDX:
0000000000000000 RSI:
0000000000000001 RDI:
ffff8c0620ab20e0
[ 8172.774629] RBP:
ffff967f00663dd8 R08:
0000000000000000 R09:
0000000000000000
[ 8172.776094] R10:
ffff8c0620ab22f8 R11:
ffff8c063f772688 R12:
ffff967f00663b78
[ 8172.777533] R13:
ffff8c063f625600 R14:
ffff8c063f625608 R15:
dead000000000200
[ 8172.778886] FS:
0000000000000000(0000) GS:
ffff8c063d400000(0000) knlGS:
0000000000000000
[ 8172.780545] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 8172.781787] CR2:
0000000000000058 CR3:
000000004e962000 CR4:
00000000000006f0
[ 8172.783547] Call Trace:
[ 8172.784112] shrink_inactive_list+0x194/0x410
[ 8172.784747] shrink_node_memcg.constprop.85+0x3a5/0x6a0
[ 8172.785472] shrink_node+0x62/0x1e0
[ 8172.786011] balance_pgdat+0x216/0x460
[ 8172.786577] kswapd+0xe3/0x4a0
[ 8172.787085] ? finish_wait+0x80/0x80
[ 8172.787795] ? balance_pgdat+0x460/0x460
[ 8172.788799] kthread+0x116/0x130
[ 8172.789640] ? kthread_create_on_node+0x60/0x60
[ 8172.790323] ret_from_fork+0x24/0x30
[ 8172.794253] CR2:
0000000000000058
or accounting errors at umount time:
[ 8159.537251] WARNING: CPU: 2 PID: 19031 at fs/btrfs/extent-tree.c:5987 btrfs_free_block_groups+0x3d5/0x410 [btrfs]
[ 8159.543325] CPU: 2 PID: 19031 Comm: umount Tainted: G W 5.0.0-rc2-default #408
[ 8159.545472] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.11.2-0-gf9626cc-prebuilt.qemu-project.org 04/01/2014
[ 8159.548155] RIP: 0010:btrfs_free_block_groups+0x3d5/0x410 [btrfs]
[ 8159.554030] RSP: 0018:
ffff967f079cbde8 EFLAGS:
00010206
[ 8159.555144] RAX:
0000000001000000 RBX:
ffff8c06366cf800 RCX:
0000000000000000
[ 8159.556730] RDX:
0000000000000002 RSI:
0000000000000001 RDI:
ffff8c06255ad800
[ 8159.558279] RBP:
ffff8c0637ac0000 R08:
0000000000000001 R09:
0000000000000000
[ 8159.559797] R10:
0000000000000000 R11:
0000000000000001 R12:
ffff8c0637ac0108
[ 8159.561296] R13:
ffff8c0637ac0158 R14:
0000000000000000 R15:
dead000000000100
[ 8159.562852] FS:
00007f7f693b9fc0(0000) GS:
ffff8c063d800000(0000) knlGS:
0000000000000000
[ 8159.564839] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 8159.566160] CR2:
00007f7f68fab7b0 CR3:
000000000aec7000 CR4:
00000000000006e0
[ 8159.567898] Call Trace:
[ 8159.568597] close_ctree+0x17f/0x350 [btrfs]
[ 8159.569628] generic_shutdown_super+0x64/0x100
[ 8159.570808] kill_anon_super+0x14/0x30
[ 8159.571857] btrfs_kill_super+0x12/0xa0 [btrfs]
[ 8159.573063] deactivate_locked_super+0x29/0x60
[ 8159.574234] cleanup_mnt+0x3b/0x70
[ 8159.575176] task_work_run+0x98/0xc0
[ 8159.576177] exit_to_usermode_loop+0x83/0x90
[ 8159.577315] do_syscall_64+0x15b/0x180
[ 8159.578339] entry_SYSCALL_64_after_hwframe+0x49/0xbe
This fix is based on 2 Josef's patches that used sideefects of
btrfs_create_pending_block_groups, this fix introduces the helper that
does what we need.
CC: stable@vger.kernel.org # 4.4+
CC: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Al Viro [Sun, 27 Jan 2019 04:58:00 +0000 (04:58 +0000)]
btrfs: fix potential oops in device_list_add
alloc_fs_devices() can return ERR_PTR(-ENOMEM), so dereferencing its
result before the check for IS_ERR() is a bad idea.
Fixes: d1a63002829a4 ("btrfs: add members to fs_devices to track fsid changes")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Jianchao Wang [Wed, 30 Jan 2019 09:01:56 +0000 (17:01 +0800)]
blk-mq: fix a hung issue when fsync
Florian reported a io hung issue when fsync(). It should be
triggered by following race condition.
data + post flush a flush
blk_flush_complete_seq
case REQ_FSEQ_DATA
blk_flush_queue_rq
issued to driver blk_mq_dispatch_rq_list
try to issue a flush req
failed due to NON-NCQ command
.queue_rq return BLK_STS_DEV_RESOURCE
request completion
req->end_io // doesn't check RESTART
mq_flush_data_end_io
case REQ_FSEQ_POSTFLUSH
blk_kick_flush
do nothing because previous flush
has not been completed
blk_mq_run_hw_queue
insert rq to hctx->dispatch
due to RESTART is still set, do nothing
To fix this, replace the blk_mq_run_hw_queue in mq_flush_data_end_io
with blk_mq_sched_restart to check and clear the RESTART flag.
Fixes: bd166ef1 (blk-mq-sched: add framework for MQ capable IO schedulers)
Reported-by: Florian Stecker <m19@florianstecker.de>
Tested-by: Florian Stecker <m19@florianstecker.de>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Tetsuo Handa [Wed, 30 Jan 2019 13:21:45 +0000 (22:21 +0900)]
block: pass no-op callback to INIT_WORK().
syzbot is hitting flush_work() warning caused by commit
4d43d395fed12463
("workqueue: Try to catch flush_work() without INIT_WORK().") [1].
Although that commit did not expect INIT_WORK(NULL) case, calling
flush_work() without setting a valid callback should be avoided anyway.
Fix this problem by setting a no-op callback instead of NULL.
[1] https://syzkaller.appspot.com/bug?id=
e390366bc48bc82a7c668326e0663be3b91cbd29
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-and-tested-by: syzbot <syzbot+ba2a929dcf8e704c180e@syzkaller.appspotmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Paul Elder [Wed, 30 Jan 2019 14:13:21 +0000 (08:13 -0600)]
usb: gadget: musb: fix short isoc packets with inventra dma
Handling short packets (length < max packet size) in the Inventra DMA
engine in the MUSB driver causes the MUSB DMA controller to hang. An
example of a problem that is caused by this problem is when streaming
video out of a UVC gadget, only the first video frame is transferred.
For short packets (mode-0 or mode-1 DMA), MUSB_TXCSR_TXPKTRDY must be
set manually by the driver. This was previously done in musb_g_tx
(musb_gadget.c), but incorrectly (all csr flags were cleared, and only
MUSB_TXCSR_MODE and MUSB_TXCSR_TXPKTRDY were set). Fixing that problem
allows some requests to be transferred correctly, but multiple requests
were often put together in one USB packet, and caused problems if the
packet size was not a multiple of 4. Instead, set MUSB_TXCSR_TXPKTRDY
in dma_controller_irq (musbhsdma.c), just like host mode transfers.
This topic was originally tackled by Nicolas Boichat [0] [1] and is
discussed further at [2] as part of his GSoC project [3].
[0] https://groups.google.com/forum/?hl=en#!topic/beagleboard-gsoc/k8Azwfp75CU
[1] https://gitorious.org/beagleboard-usbsniffer/beagleboard-usbsniffer-kernel/commit/
b0be3b6cc195ba732189b04f1d43ec843c3e54c9?p=beagleboard-usbsniffer:beagleboard-usbsniffer-kernel.git;a=patch;h=
b0be3b6cc195ba732189b04f1d43ec843c3e54c9
[2] http://beagleboard-usbsniffer.blogspot.com/2010/07/musb-isochronous-transfers-fixed.html
[3] http://elinux.org/BeagleBoard/GSoC/USBSniffer
Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support")
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vincent Whitchurch [Tue, 29 Jan 2019 10:22:07 +0000 (11:22 +0100)]
mic: vop: Fix broken virtqueues
VOP is broken in mainline since commit
1ce9e6055fa0a9043 ("virtio_ring:
introduce packed ring support"); attempting to use the virtqueues leads
to various kernel crashes. I'm testing it with my not-yet-merged
loopback patches, but even the in-tree MIC hardware cannot work.
The problem is not in the referenced commit per se, but is due to the
following hack in vop_find_vq() which depends on the layout of private
structures in other source files, which that commit happened to change:
/*
* To reassign the used ring here we are directly accessing
* struct vring_virtqueue which is a private data structure
* in virtio_ring.c. At the minimum, a BUILD_BUG_ON() in
* vring_new_virtqueue() would ensure that
* (&vq->vring == (struct vring *) (&vq->vq + 1));
*/
vr = (struct vring *)(vq + 1);
vr->used = used;
Fix vop by using __vring_new_virtqueue() to create the needed vring
layout from the start, instead of attempting to patch in the used ring
later. __vring_new_virtqueue() was added way back in commit
2a2d1382fe9dcc ("virtio: Add improved queue allocation API") in order to
address mic's usecase, according to the commit message.
Fixes: 1ce9e6055fa0 ("virtio_ring: introduce packed ring support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gao Xiang [Tue, 29 Jan 2019 15:55:40 +0000 (23:55 +0800)]
staging: erofs: keep corrupted fs from crashing kernel in erofs_namei()
As Al pointed out, "
... and while we are at it, what happens to
unsigned int nameoff = le16_to_cpu(de[mid].nameoff);
unsigned int matched = min(startprfx, endprfx);
struct qstr dname = QSTR_INIT(data + nameoff,
unlikely(mid >= ndirents - 1) ?
maxsize - nameoff :
le16_to_cpu(de[mid + 1].nameoff) - nameoff);
/* string comparison without already matched prefix */
int ret = dirnamecmp(name, &dname, &matched);
if le16_to_cpu(de[...].nameoff) is not monotonically increasing? I.e.
what's to prevent e.g. (unsigned)-1 ending up in dname.len?
Corrupted fs image shouldn't oops the kernel.. "
Revisit the related lookup flow to address the issue.
Fixes: d72d1ce60174 ("staging: erofs: add namei functions")
Cc: <stable@vger.kernel.org> # 4.19+
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aaro Koskinen [Sun, 27 Jan 2019 19:54:50 +0000 (21:54 +0200)]
staging: octeon: fix broken phylib usage
Commit
2b3e88ea6528 ("net: phy: improve phy state checking")
added checks for phylib usage, and this triggers with OCTEON ethernet
and results in broken networking.
Fix by replacing phy_start_aneg() with phy_start().
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Usyskin [Wed, 30 Jan 2019 08:12:26 +0000 (10:12 +0200)]
mei: free read cb on ctrl_wr list flush
There is a little window during disconnection flow
when read cb is moved between lists and may be not freed.
Remove moving read cbs explicitly during flash fixes this memory
leak.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 24 Jan 2019 12:45:03 +0000 (14:45 +0200)]
samples: mei: use /dev/mei0 instead of /dev/mei
The device was moved from misc device to character devices
to support multiple mei devices.
Cc: <stable@vger.kernel.org> #v4.9+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 24 Jan 2019 12:45:02 +0000 (14:45 +0200)]
mei: me: add ice lake point device id.
Add icelake mei device id.
Cc: <stable@vger.kernel.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Brauner [Wed, 23 Jan 2019 11:41:15 +0000 (12:41 +0100)]
binderfs: respect limit on binder control creation
We currently adhere to the reserved devices limit when creating new
binderfs devices in binderfs instances not located in the inital ipc
namespace. But it is still possible to rob the host instances of their 4
reserved devices by creating the maximum allowed number of devices in a
single binderfs instance located in a non-initial ipc namespace and then
mounting 4 separate binderfs instances in non-initial ipc namespaces. That
happens because the limit is currently not respected for the creation of
the initial binder-control device node. Block this nonsense by performing
the same check in binderfs_binder_ctl_create() that we perform in
binderfs_binder_device_create().
Fixes: 36bdf3cae09d ("binderfs: reserve devices for initial mount")
Signed-off-by: Christian Brauner <christian@brauner.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Brauner [Sat, 26 Jan 2019 10:23:20 +0000 (11:23 +0100)]
binder: fix CONFIG_ANDROID_BINDER_DEVICES
Several users have tried to only rely on binderfs to provide binder devices
and set CONFIG_ANDROID_BINDER_DEVICES="" empty. This is a great use-case of
binderfs and one that was always intended to work. However, this is
currently not possible since setting CONFIG_ANDROID_BINDER_DEVICES="" emtpy
will simply panic the kernel:
kobject: (
00000000028c2f79): attempted to be registered with empty name!
WARNING: CPU: 7 PID: 1703 at lib/kobject.c:228 kobject_add_internal+0x288/0x2b0
Modules linked in: binder_linux(+) bridge stp llc ipmi_ssif gpio_ich dcdbas coretemp kvm_intel kvm irqbypass serio_raw input_leds lpc_ich i5100_edac mac_hid ipmi_si ipmi_devintf ipmi_msghandler sch_fq_codel ib_i
CPU: 7 PID: 1703 Comm: modprobe Not tainted 5.0.0-rc2-brauner-binderfs #263
Hardware name: Dell DCS XS24-SC2 /XS24-SC2 , BIOS S59_3C20 04/07/2011
RIP: 0010:kobject_add_internal+0x288/0x2b0
Code: 12 95 48 c7 c7 78 63 3b 95 e8 77 35 71 ff e9 91 fe ff ff 0f 0b eb a7 0f 0b eb 9a 48 89 de 48 c7 c7 00 63 3b 95 e8 f8 95 6a ff <0f> 0b 41 bc ea ff ff ff e9 6d fe ff ff 41 bc fe ff ff ff e9 62 fe
RSP: 0018:
ffff973f84237a30 EFLAGS:
00010282
RAX:
0000000000000000 RBX:
ffff8b53e2472010 RCX:
0000000000000006
RDX:
0000000000000007 RSI:
0000000000000086 RDI:
ffff8b53edbd63a0
RBP:
ffff973f84237a60 R08:
0000000000000342 R09:
0000000000000004
R10:
ffff973f84237af0 R11:
0000000000000001 R12:
0000000000000000
R13:
ffff8b53e9f1a1e0 R14:
00000000e9f1a1e0 R15:
0000000000a00037
FS:
00007fbac36f7540(0000) GS:
ffff8b53edbc0000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007fbac364cfa7 CR3:
00000004a6d48000 CR4:
00000000000406e0
Call Trace:
kobject_add+0x71/0xd0
? _cond_resched+0x19/0x40
? mutex_lock+0x12/0x40
device_add+0x12e/0x6b0
device_create_groups_vargs+0xe4/0xf0
device_create_with_groups+0x3f/0x60
? _cond_resched+0x19/0x40
misc_register+0x140/0x180
binder_init+0x1ed/0x2d4 [binder_linux]
? trace_event_define_fields_binder_transaction_fd_send+0x8e/0x8e [binder_linux]
do_one_initcall+0x4a/0x1c9
? _cond_resched+0x19/0x40
? kmem_cache_alloc_trace+0x151/0x1c0
do_init_module+0x5f/0x216
load_module+0x223d/0x2b20
__do_sys_finit_module+0xfc/0x120
? __do_sys_finit_module+0xfc/0x120
__x64_sys_finit_module+0x1a/0x20
do_syscall_64+0x5a/0x120
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fbac3202839
Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1f f6 2c 00 f7 d8 64 89 01 48
RSP: 002b:
00007ffd1494a908 EFLAGS:
00000246 ORIG_RAX:
0000000000000139
RAX:
ffffffffffffffda RBX:
000055b629ebec60 RCX:
00007fbac3202839
RDX:
0000000000000000 RSI:
000055b629c20d2e RDI:
0000000000000003
RBP:
000055b629c20d2e R08:
0000000000000000 R09:
000055b629ec2310
R10:
0000000000000003 R11:
0000000000000246 R12:
0000000000000000
R13:
000055b629ebed70 R14:
0000000000040000 R15:
000055b629ebec60
So check for the empty string since strsep() will otherwise return the
emtpy string which will cause kobject_add_internal() to panic when trying
to add a kobject with an emtpy name.
Fixes: ac4812c5ffbb ("binder: Support multiple /dev instances")
Cc: Martijn Coenen <maco@google.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Brauner [Thu, 17 Jan 2019 11:48:54 +0000 (12:48 +0100)]
selftests: add binderfs selftests
This adds the promised selftest for binderfs. It will verify the following
things:
- binderfs mounting works
- binder device allocation works
- performing a binder ioctl() request through a binderfs device works
- binder device removal works
- binder-control removal fails
- binderfs unmounting works
The tests are performed both privileged and unprivileged. The latter
verifies that binderfs behaves correctly in user namespaces.
Cc: Todd Kjos <tkjos@google.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 30 Jan 2019 11:37:35 +0000 (12:37 +0100)]
debugfs: debugfs_lookup() should return NULL if not found
Lots of callers of debugfs_lookup() were just checking NULL to see if
the file/directory was found or not. By changing this in
ff9fb72bc077
("debugfs: return error values, not NULL") we caused some subsystems to
easily crash.
Fixes: ff9fb72bc077 ("debugfs: return error values, not NULL")
Reported-by: syzbot+b382ba6a802a3d242790@syzkaller.appspotmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 30 Jan 2019 09:49:34 +0000 (10:49 +0100)]
staging: speakup: fix tty-operation NULL derefs
The send_xchar() and tiocmset() tty operations are optional. Add the
missing sanity checks to prevent user-space triggerable NULL-pointer
dereferences.
Fixes: 6b9ad1c742bf ("staging: speakup: add send_xchar, tiocmset and input functionality for tty")
Cc: stable <stable@vger.kernel.org> # 4.13
Cc: Okash Khawaja <okash.khawaja@gmail.com>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Borislav Petkov [Thu, 24 Jan 2019 10:18:48 +0000 (11:18 +0100)]
MAINTAINERS: Add Andy and Darren as arch/x86/platform/ reviewers
... so that they can get CCed on platform patches.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/20190128113619.19025-1-bp@alien8.de
Chris Brandt [Mon, 28 Jan 2019 18:25:56 +0000 (13:25 -0500)]
serial: sh-sci: Do not free irqs that have already been freed
Since IRQs might be muxed on some parts, we need to pay attention when we
are freeing them.
Otherwise we get the ugly WARNING "Trying to free already-free IRQ 20".
Fixes: 628c534ae735 ("serial: sh-sci: Improve support for separate TEI and DRI interrupts")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Thu, 24 Jan 2019 21:51:21 +0000 (23:51 +0200)]
serial: 8250_pci: Make PCI class test non fatal
As has been reported the National Instruments serial cards have broken
PCI class.
The commit
7d8905d06405
("serial: 8250_pci: Enable device after we check black list")
made the PCI class check mandatory for the case when device is listed in
a quirk list.
Make PCI class test non fatal to allow broken card be enumerated.
Fixes: 7d8905d06405 ("serial: 8250_pci: Enable device after we check black list")
Cc: stable <stable@vger.kernel.org>
Reported-by: Guan Yung Tseng <guan.yung.tseng@ni.com>
Tested-by: Guan Yung Tseng <guan.yung.tseng@ni.com>
Tested-by: KHUENY.Gerhard <Gerhard.KHUENY@bachmann.info>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Tue, 22 Jan 2019 19:57:19 +0000 (13:57 -0600)]
tty: serial: 8250_mtk: Fix potential NULL pointer dereference
There is a potential NULL pointer dereference in case devm_kzalloc()
fails and returns NULL.
Fix this by adding a NULL check on data->dma
This bug was detected with the help of Coccinelle.
Fixes: 85b5c1dd0456 ("serial: 8250-mtk: add uart DMA support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexei Starovoitov [Wed, 30 Jan 2019 03:15:33 +0000 (19:15 -0800)]
Merge branch 'typedef-func_proto'
Yonghong Song says:
====================
The current btf implementation disallows the typedef of
a func_proto type. This actually is allowed per C standard.
This patch fixed btf verification to permit such types.
Patch #1 fixed the kernel side and Patch #2 fixed
the tools test_btf test.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Yonghong Song [Wed, 30 Jan 2019 00:38:17 +0000 (16:38 -0800)]
tools/bpf: fix test_btf for typedef func_proto case
Fixed one test_btf raw test such that typedef func_proto
is permitted now.
Fixes: 78a2540e8945 ("tools/bpf: Add tests for BTF_KIND_FUNC_PROTO and BTF_KIND_FUNC")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Yonghong Song [Wed, 30 Jan 2019 00:38:16 +0000 (16:38 -0800)]
bpf: btf: allow typedef func_proto
Current implementation does not allow typedef func_proto.
But it is actually allowed.
-bash-4.4$ cat t.c
typedef int (f) (int);
f *g;
-bash-4.4$ clang -O2 -g -c -target bpf t.c -Xclang -target-feature -Xclang +dwarfris
-bash-4.4$ pahole -JV t.o
File t.o:
[1] PTR (anon) type_id=2
[2] TYPEDEF f type_id=3
[3] FUNC_PROTO (anon) return=4 args=(4 (anon))
[4] INT int size=4 bit_offset=0 nr_bits=32 encoding=SIGNED
-bash-4.4$
This patch related btf verifier to allow such (typedef func_proto)
patterns.
Fixes: 2667a2626f4d ("bpf: btf: Add BTF_KIND_FUNC and BTF_KIND_FUNC_PROTO")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This page took 0.154928 seconds and 4 git commands to generate.
projects / linux.git / log