powerpc/pseries: Fix a typo in pSeries_lpar_hpte_insert()
Commit 801eb73f45371accc78ca9d6d22d647eeb722c11 introduced
a bug while checking PTE flags. We have to drop the _PAGE_COHERENT flag
when __PAGE_NO_CACHE is set and the cache update policy is not write-through
(i.e. _PAGE_WRITETHRU is not set)
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
This patch restores serial port operation which has been broken since
commit 60e93575476f ("serial: samsung: enable clock before clearing
pending interrupts during init")
That commit only uncovered the real issue which was missing clkdev
entries for the "uart" clocks on S3C2440. It went unnoticed so far
because return value of clk API calls were not being checked at all
in the samsung serial port driver.
This patch should be backported to at least 3.10 stable kernel, since
the serial port has not been working on s3c2440 since 3.10-rc5.
The patch introduces flag EEH_DEV_SYSFS to keep track that the sysfs
entries for the corresponding EEH device (then PCI device) has been
added or removed, in order to avoid race condition.
While restoring BARs for one specific PCI device, the pci_dev
instance should have been released. So it's not reliable to use
the pci_dev instance on restoring BARs. However, we still need
some information (e.g. PCIe capability position, header type) from
the pci_dev instance. So we have to store those information to
EEH device in advance.
powerpc/eeh: Use partial hotplug for EEH unaware drivers
When EEH error happens to one specific PE, some devices with drivers
supporting EEH won't except hotplug on the device. However, there
might have other deivces without driver, or with driver without EEH
support. For the case, we need do partial hotplug in order to make
sure that the PE becomes absolutely quite during reset. Otherise,
the PE reset might fail and leads to failure of error recovery.
The current code doesn't handle that 'mixed' case properly, it either
uses the error callbacks to the drivers, or tries hotplug, but doesn't
handle a PE (EEH domain) composed of a combination of the two.
The patch intends to support so-called "partial" hotplug for EEH:
Before we do reset, we stop and remove those PCI devices without
EEH sensitive driver. The corresponding EEH devices are not detached
from its PE, but with special flag. After the reset is done, those
EEH devices with the special flag will be scanned one by one.
When EEH error happens to one specific PE, the device drivers
of its attached EEH devices (PCI devices) are checked to see
the further action: reset with complete hotplug, or reset without
hotplug. However, that's not enough for those PCI devices whose
drivers can't support EEH, or those PCI devices without driver.
So we need do so-called "partial hotplug" on basis of PCI devices.
In the situation, part of PCI devices of the specific PE are
unplugged and plugged again after PE reset.
The patch changes pcibios_add_pci_devices() so that it can support
full hotplug and so-called "partial" hotplug based on device-tree
or real hardware. It's notable that pci_of_scan.c has been changed
for a bit in order to support the "partial" hotplug based on dev-tree.
Most of the generic code already supports that, we just need to
plumb it properly on our side.
powerpc/eeh: Use safe list traversal when walking EEH devices
Currently, we're trasversing the EEH devices list using list_for_each_entry().
That's not safe enough because the EEH devices might be removed from
its parent PE while doing iteration. The patch replaces that with
list_for_each_entry_safe().
When we do normal hotplug, the PE (shadow EEH structure) shouldn't be
kept around.
However, we need to keep it if the hotplug an artifial one caused by
EEH errors recovery.
Since we remove EEH device through the PCI hook pcibios_release_device(),
the flag "purge_pe" passed to various functions is meaningless. So the patch
removes the meaningless flag and introduce new flag "EEH_PE_KEEP"
to save the PE while doing hotplug during EEH error recovery.
We will rely on pcibios_release_device() to remove the EEH cache
and unbind EEH device for the specific PCI device. So we shouldn't
hold the reference to the PCI device from EEH cache and EEH device.
Otherwise, pcibios_release_device() won't be called as we expected.
The patch removes the reference to the PCI device in EEH core.
powerpc: Fix the corrupt r3 error during MCE handling.
During Machine Check interrupt on pseries platform, R3 generally points to
memory region inside RTAS (FWNMI) area. We see r3 corruption because when RTAS
delivers the machine check exception it passes the address inside FWNMI area
with the top most bit set. This patch fixes this issue by masking top two bit
in machine check exception handler.
Michael Ellerman [Sat, 13 Jul 2013 02:53:40 +0000 (12:53 +1000)]
powerpc/perf: Set PPC_FEATURE2_EBB when we register the power8 PMU
The presence or absence of EBB is advertised to userspace via the presence
or absence of PPC_FEATURE2_EBB in cpu_user_features2.
Because the kernel can be built without PMU support, we should only add
PPC_FEATURE2_EBB to cpu_user_features2 when we successfully register the
power8 PMU support.
Paul Bolle [Sun, 14 Jul 2013 11:02:15 +0000 (13:02 +0200)]
powerpc/pseries: Drop "select HOTPLUG"
The Kconfig symbol HOTPLUG was removed with commit 40b313608a ("Finally
eradicate CONFIG_HOTPLUG"). But there's still one select statement for
that symbol. It seems that select statement was added after the patch to
remove CONFIG_HOTPLUG was submitted. Anyhow, it is useless and can be
dropped.
powerpc: Access local paca after hard irq disabled
In hard_irq_disable(), we accessed the PACA before we hard disabled
the interrupts, potentially causing a warning as get_paca() will
us debug_smp_processor_id().
Move that to after the disabling, and also use local_paca directly
rather than get_paca() to avoid several redundant and useless checks.
Module CRCs are implemented as absolute symbols that get resolved by
a linker script. We build an intermediate .o that contains an
unresolved symbol for each CRC. genksysms parses this .o, calculates
the CRCs and writes a linker script that "resolves" the symbols to
the calculated CRC.
Unfortunately the ppc64 relocatable kernel sees these CRCs as symbols
that need relocating and relocates them at boot. Commit d4703aef
(module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y)
added a hook to reverse the bogus relocations. Part of this patch
created a symbol at 0x0:
This reloc_start symbol is causing lots of confusion to perf. It
thinks reloc_start is a massive function that stretches from 0x0 to
0xc000000000000000 and we get various cryptic errors out of perf,
including:
problem incrementing symbol count, skipping event
This patch removes the reloc_start linker script label and instead
defines it as PHYSICAL_START. We also need to wrap it with
CONFIG_PPC64 because the ppc32 kernel can set a non zero
PHYSICAL_START at compile time and we wouldn't want to subtract
it from the CRCs in that case.
Tomas Winkler [Wed, 17 Jul 2013 12:13:17 +0000 (15:13 +0300)]
mei: me: fix waiting for hw ready
1. MEI_INTEROP_TIMEOUT is in seconds not in jiffies
so we use mei_secs_to_jiffies macro
While cold boot is fast this is relevant in resume
2. wait_event_interruptible_timeout can return with
-ERESTARTSYS so do not override it with -ETIMEDOUT
3.Adjust error message
Tomas Winkler [Wed, 17 Jul 2013 12:13:15 +0000 (15:13 +0300)]
mei: me: fix reset state machine
ME HW ready bit is down after hw reset was asserted or on error.
Only on error we need to enter the reset flow, additional reset
need to be prevented when reset was triggered during
initialization , power up/down or a reset is already in progress
Dave Airlie [Tue, 23 Jul 2013 04:16:42 +0000 (14:16 +1000)]
qxl: convert qxl driver to proper use for reservations
The recent addition of lockdep support to reservations and their subsequent
use by TTM showed up a number of potential problems with the way qxl was using
TTM objects.
a) it was allocating objects, and reserving them later without validating
underneath the reservation, which meant in extreme conditions the objects could
be evicted before the reservation ever used them.
b) it was reserving objects straight after allocating them, but with no
ability to back off should the reservations fail. It now allocates the necessary
objects then does a complete reservation pass on them to avoid deadlocks.
c) it had two lists per release tracking objects, unnecessary complicating
the reservation process.
This patch removes the dual object tracking, adds reservations ticket support
to the release and fence object handling. It then ports the internal fb
drawing code and the userspace facing ioctl to use the new interfaces properly,
along with cleanup up the error path handling in some codepaths.
Dave Airlie [Tue, 23 Jul 2013 04:06:07 +0000 (14:06 +1000)]
qxl: allow creation of pre-pinned objects and use for releases.
In order to fix an issue with reservations we need to create the releases
as pre-pinned objects, this changes the placement interface and bo creation
interface to allow creating pinned objects to save nested reservations later.
This is just a stepping stone to main fix which follows to actually fix how
qxl deals with reservations.
Dave Airlie [Mon, 22 Jul 2013 04:37:39 +0000 (14:37 +1000)]
drm/qxl: add delayed fb operations
Due to the nature of qxl hw we cannot queue operations while in an irq
context, so we queue these operations as best we can until atomic allocations
fail, and dequeue them later in a work queue.
Daniel looked over the locking on the list and agrees it should be sufficent.
The atomic allocs use no warn, as the last thing we want if we haven't memory
to allocate space for a printk in an irq context is more printks.
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree bug fixes and maintainership updates from Grant Likely:
"This branch contains a couple of minor bug fixes and documentation
additions, but the bulk of it are several changes to the MAINTAINERS
file regarding the subsystems I've been involved with"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: init struct resource to 0 in of_irq_to_resource()
of/irq: Avoid calling list_first_entry() for empty list
of: add vendor prefixes for hisilicon
of: add vendor prefix for Qualcomm Atheros, Inc.
MAINTAINERS: Fix incorrect status tag
MAINTAINERS: Refactor device tree maintainership
MAINTAINERS: Change device tree mailing list
MAINTAINERS: Remove Grant Likely
What happens is that bus_register needs a statically allocated lock_key
because the last is handed in to lockdep. However, struct mem_ctl_info
embeds struct bus_type (the whole struct, not a pointer to it) and the
whole thing gets dynamically allocated.
Fix this by using a statically allocated struct bus_type for the MC bus.
Merge branch 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup changes from Tejun Heo:
"This contains two patches, both of which aren't fixes per-se but I
think it'd be better to fast-track them.
One removes bcache_subsys_id which was added without proper review
through the block tree. Fortunately, bcache cgroup code is
unconditionally disabled, so this was never exposed to userland. The
cgroup subsys_id is removed. Kent will remove the affected (disabled)
code through bcache branch.
The other simplifies task_group_path_from_hierarchy(). The function
doesn't currently have in-kernel users but there are external code and
development going on dependent on the function and making the function
available for 3.11 would make things go smoother"
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: replace task_cgroup_path_from_hierarchy() with task_cgroup_path()
cgroup: remove bcache_subsys_id which got added stealthily
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is just a regular fixes pull, mostly nouveau and i915, the i915
ones fix RC6 on Sandybridge after suspend/resume, which I think people
have be wanting for quite a while!
Now you shouldn't wish for more patches, as the new mutex/reservation
code found a number of problems with the qxl driver, and it currently
makes lockdep angry, I'm working on a set of fixes for it, but its a
bit large, I'll submit them separately later today or tomorrow once
I've banged on them a bit more, just warning you in advance :-)"
Yeah, I'm definitely over the whole "wish for more patches" thing.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/crtc-helper: explicit DPMS on after modeset
drm/i915: fix up gt init sequence fallout
drm/i915: Serialize almost all register access
drm/i915: quirk no PCH_PWM_ENABLE for Dell XPS13 backlight
drm/i915: correctly restore fences with objects attached
drm/i915: Fix dereferencing invalid connectors in is_crtc_connector_off()
drm/i915: Sanitize shared dpll state
drm/i915: fix long-standing SNB regression in power consumption after resume v2
drm/i915: Preserve the DDI_A_4_LANES bit from the bios
drm/i915: fix pfit regression for non-autoscaled resolutions
drm/i915: fix up readout of the lvds dither bit on gen2/3
drm/nouveau: do not allow negative sizes for now
drm/nouveau: add falcon interrupt handler
drm/nouveau: use dedicated channel for async moves on GT/GF chipsets.
drm/nouveau: bump fence timeout to 15 seconds
drm/nouveau: do not unpin in nouveau_gem_object_del
drm/nv50/kms: fix pin refcnt leaks
drm/nouveau: fix some error-path leaks in fbcon handling code
drm/nouveau: fix locking issues in page flipping paths
David Howells [Tue, 23 Jul 2013 15:49:24 +0000 (16:49 +0100)]
Fix __wait_on_atomic_t() to call the action func if the counter != 0
Fix __wait_on_atomic_t() so that it calls the action func if the counter != 0
rather than if the counter is 0 so as to be analogous to __wait_on_bit().
Thanks to Yacine who found this by visual inspection.
This will affect FS-Cache in that it will could fail to sleep correctly when
trying to clean up after a netfs cookie is withdrawn.
James Bottomley [Sun, 9 Jun 2013 16:23:16 +0000 (09:23 -0700)]
[SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
slot->response is a 64 bit quantity (and accessed as such), but its alignment
is only 32 bits. This doesn't cause a problem on x86, but apparently causes a
kernel panic on Tile:
Since the check is just for non-zero, split it to be two 32 bit accesses
(preserving speed in the fast path) and do a get_unaligned() in the slow path.
This is a modification of a wholly get_unaligned patch submitted by Paul Guo
staging: android: logger: Correct write offset reset on error
In the situation that a writer fails to copy data from userspace it will reset
the write offset to the value it had before it went to sleep. This discarding
any messages written while aquiring the mutex.
Therefore the reset offset needs to be retrieved after acquiring the mutex.
Paul Bolle [Sun, 14 Jul 2013 11:29:48 +0000 (13:29 +0200)]
staging: drm/imx: drop "select OF_VIDEOMODE"
Commit ac4c1a9b33 ("staging: drm/imx: Add LDB support") added the
DRM_IMX_LDB Kconfig entry. That entry selects OF_VIDEOMODE. But there is
no Kconfig symbol named OF_VIDEOMODE. The select statement for that
symbol is a nop. Drop it.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha architecture fixes from Matt Turner:
"This contains mostly clean ups and fixes but also an implementation of
atomic64_dec_if_positive() and a pair of new syscalls"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: Use handle_percpu_irq for the timer interrupt
alpha: Force the user-visible HZ to a constant 1024.
alpha: Don't if-out dp264_device_interrupt.
alpha: Use __builtin_alpha_rpcc
alpha: Fix type compatibility warning for marvel_map_irq
alpha: Generate dwarf2 unwind info for various kernel entry points.
alpha: Implement atomic64_dec_if_positive
alpha: Improve atomic_add_unless
alpha: Modernize lib/mpi/longlong.h
alpha: Add kcmp and finit_module syscalls
alpha: locks: remove unused arch_*_relax operations
alpha: kernel: typo issue, using '1' instead of '11'
alpha: kernel: using memcpy() instead of strcpy()
alpha: Convert print_symbol to %pSR
Ian Abbott [Fri, 5 Jul 2013 15:49:34 +0000 (16:49 +0100)]
staging: comedi: fix a race between do_cmd_ioctl() and read/write
`do_cmd_ioctl()` is called with the comedi device's mutex locked to
process the `COMEDI_CMD` ioctl to set up comedi's asynchronous command
handling on a comedi subdevice. `comedi_read()` and `comedi_write()`
are the `read` and `write` handlers for the comedi device, but do not
lock the mutex (for performance reasons, as some things can hold the
mutex for quite a long time).
There is a race condition if `comedi_read()` or `comedi_write()` is
running at the same time and for the same file object and comedi
subdevice as `do_cmd_ioctl()`. `do_cmd_ioctl()` sets the subdevice's
`busy` pointer to the file object way before it sets the `SRF_RUNNING` flag
in the subdevice's `runflags` member. `comedi_read() and
`comedi_write()` check the subdevice's `busy` pointer is pointing to the
current file object, then if the `SRF_RUNNING` flag is not set, will call
`do_become_nonbusy()` to shut down the asyncronous command. Bad things
can happen if the asynchronous command is being shutdown and set up at
the same time.
To prevent the race, don't set the `busy` pointer until
after the `SRF_RUNNING` flag has been set. Also, make sure the mutex is
held in `comedi_read()` and `comedi_write()` while calling
`do_become_nonbusy()` in order to avoid moving the race condition to a
point within that function.
Change some error handling `goto cleanup` statements in `do_cmd_ioctl()`
to simple `return -ERRFOO` statements as a result of changing when the
`busy` pointer is set.
Ian Abbott [Mon, 8 Jul 2013 12:36:19 +0000 (13:36 +0100)]
staging: comedi: COMEDI_CANCEL ioctl should wake up read/write
Comedi devices can do blocking read() or write() (or poll()) if an
asynchronous command has been set up, blocking for data (for read()) or
buffer space (for write()). Various events associated with the
asynchronous command will wake up the blocked reader or writer (or
poller). It is also possible to force the asynchronous command to
terminate by issuing a `COMEDI_CANCEL` ioctl. That shuts down the
asynchronous command, but does not currently wake up the blocked reader
or writer (or poller). If the blocked task could be woken up, it would
see that the command is no longer active and return. The caller of the
`COMEDI_CANCEL` ioctl could attempt to wake up the blocked task by
sending a signal, but that's a nasty workaround.
Change `do_cancel_ioctl()` to wake up the wait queue after it returns
from `do_cancel()`. `do_cancel()` can propagate an error return value
from the low-level comedi driver's cancel routine, but it always shuts
the command down regardless, so `do_cancel_ioctl()` can wake up he wait
queue regardless of the return value from `do_cancel()`.
ARM: pxa: propagate errors from regulator_enable() to pxamci
The em_x270_mci_setpower() and em_x270_usb_hub_init() functions
call regulator_enable(), which may return an error that must
be checked.
This changes the em_x270_usb_hub_init() function to bail out
if it fails, and changes the pxamci_platform_data->setpower
callback so that the a failed em_x270_mci_setpower call
can be propagated by the pxamci driver into the mmc core.
Vincent Stehlé [Thu, 27 Jun 2013 12:42:41 +0000 (14:42 +0200)]
ARM: zynq: fix compilation warning
Fix the following compilation warning:
arch/arm/mach-zynq/common.c:110:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-zynq/common.c:110:2: warning: (near initialization for ‘__mach_desc_XILINX_EP107.restart’) [enabled by default]
Vincent Stehlé [Thu, 27 Jun 2013 12:49:27 +0000 (14:49 +0200)]
ARM: keystone: fix compilation warning
Fix the following compilation warning:
arch/arm/mach-keystone/keystone.c:74:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-keystone/keystone.c:74:2: warning: (near initialization for ‘__mach_desc_KEYSTONE.restart’) [enabled by default]
can result in the following state:
------------------------------------------------------------
struct nfs4_file {
...
fi_fds = {0xffff880c1fa65c80, 0xffffffffffffffe6, 0x0},
fi_access = {{
counter = 0x1
}, {
counter = 0x0
}},
...
------------------------------------------------------------
1) First time around, in nfs4_get_vfs_file() fp->fi_fds[O_WRONLY] is
NULL, hence nfsd_open() is called where we get status set to an error
and fp->fi_fds[O_WRONLY] to -ETXTBSY. Thus we do not reach
nfs4_file_get_access() and fi_access[O_WRONLY] is not incremented.
2) Second time around, in nfs4_get_vfs_file() fp->fi_fds[O_WRONLY] is
NOT NULL (-ETXTBSY), so nfsd_open() is NOT called, but
nfs4_file_get_access() IS called and fi_access[O_WRONLY] is incremented.
Thus we leave a landmine in the form of the nfs4_file data structure in
an incorrect state.
Ewan D. Milne [Fri, 2 Nov 2012 13:38:34 +0000 (09:38 -0400)]
[SCSI] sd: fix crash when UA received on DIF enabled device
sd_prep_fn will allocate a larger CDB for the command via mempool_alloc
for devices using DIF type 2 protection. This CDB was being freed
in sd_done, which results in a kernel crash if the command is retried
due to a UNIT ATTENTION. This change moves the code to free the larger
CDB into sd_unprep_fn instead, which is invoked after the request is
complete.
It is no longer necessary to call scsi_print_command separately for
this case as the ->cmnd will no longer be NULL in the normal code path.
Also removed conditional test for DIF type 2 when freeing the larger
CDB because the protection_type could have been changed via sysfs while
the command was executing.
ahci: fix Null pointer dereference in achi_host_active()
commit b29900e6 (AHCI: Make distinct names for ports in /proc/interrupts)
introuded a regression, which resulted Null pointer dereference for achi
host with dummy ports. For ahci ports, when the port is dummy port, its
private_data will be NULL, as ata_dummy_port_ops doesn't support ->port_start.
changes in v2: use pp to check dummy ports, update comments
Jeff Skirvin [Fri, 12 Jul 2013 00:18:58 +0000 (17:18 -0700)]
[SCSI] isci: Fix a race condition in the SSP task management path
This commit fixes a race condition in the isci driver abort task and SSP
device task management path. The race is caused when an I/O termination
in the SCU hardware is necessary because of an SSP target timeout condition,
and the check of the I/O end state races against the HW-termination-driven
end state. The failure of the race meant that no TMF was sent to the device
to clean-up the pending I/O.
arm64: Fix definition of arm_pm_restart to match the declaration
Commit ff70130 (arm64: use common reboot infrastructure) converted the
arm_pm_restart declaration to the new reboot infrastructure but missed
the actual definition.
Mark Rutland [Tue, 9 Jul 2013 14:16:06 +0000 (15:16 +0100)]
arm64: virt: ensure visibility of __boot_cpu_mode
Secondary CPUs write to __boot_cpu_mode with caches disabled, and thus a
cached value of __boot_cpu_mode may be incoherent with that in memory.
This could lead to a failure to detect mismatched boot modes.
This patch adds flushing to ensure that writes by secondaries to
__boot_cpu_mode are made visible before we test against it.
I've errornously claimed that we don't yet support the hdmi 1.4
dotclocks > 225 MHz on Haswell. But a bug report and a closer look at
the wrpll table showed that we've supported port clocks up to 300MHz.
With the new code to dynamically compute wrpll limits we should have
no issues going up to the full 340 MHz range of hdmi 1.4, so let's
just use that to fix this regression. That'll allow 4k over hdmi for
free!
v2: Drop the random hunk that somehow slipped in.
v3: Cantiga has the original HDMI dotclock limit of 165MHz. And also
patch up the mode filtering. To do so extract the dotclock limits into
a little helper function.
v4: Use 300MHz (from Bspec) instead of 340MHz (upper limit for hdmi
1.3), apparently hw is not required to be able to drive the highest
dotclocks. Suggested by Damien.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67048
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67030 Tested-by: Andreas Reis <[email protected]> (v2) Cc: Damien Lespiau <[email protected]> Reviewed-by: Damien Lespiau <[email protected]> Signed-off-by: Daniel Vetter <[email protected]>
Rob Herring [Sun, 21 Jul 2013 19:53:37 +0000 (14:53 -0500)]
ARM: highbank: Only touch common coherency control register fields
Midway adds new register fields to the coherency control registers, so
writing absolute values will break on Midway. Change the register
accesses to only modify the necessary and common fields in order to
support both Midway and Highbank.
Olof Johansson [Tue, 23 Jul 2013 03:02:38 +0000 (20:02 -0700)]
Merge tag 'nomadik-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into fixes
From Linus Walleij:
This updates the Nomadik defconfig post-v3.11-rc1:
- Update the baseline so we need not rely on make
oldconfig so much
- MMC defconfig updates
- Activate NO_HZ_IDLE and HRTIMERS
* tag 'nomadik-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
Mike Frysinger [Fri, 28 Jun 2013 02:42:36 +0000 (22:42 -0400)]
ARM: footbridge: fix overlapping PCI mappings
Commit 8ef6e6201b26cb9fde79c1baa08145af6aca2815 (ARM: footbridge: use
fixed PCI i/o mapping) broke booting on my netwinder. Before that,
everything boots fine. Since then, it crashes on boot.
With earlyprintk, I see it BUG-ing like so:
kernel BUG at lib/ioremap.c:27!
Internal error: Oops - BUG: 0 [#1] ARM
...
[<c0139b54>] (ioremap_page_range+0x128/0x154) from [<c02e6a6c>] (dc21285_setup+0xd0/0x114)
[<c02e6a6c>] (dc21285_setup+0xd0/0x114) from [<c02e4874>] (pci_common_init+0xa0/0x298)
[<c02e4874>] (pci_common_init+0xa0/0x298) from [<c02e793c>] (netwinder_pci_init+0xc/0x18)
[<c02e793c>] (netwinder_pci_init+0xc/0x18) from [<c02e27d0>] (do_one_initcall+0xb4/0x180)
...
Russell points out it's because of overlapping PCI mappings that was
added with the aforementioned commit. Rob thought the code would re-use
the static mapping, but that turns out to not be the case and instead
hits the BUG further down.
After deleting this hunk as suggested by Russel, the system boots up fine
again and all my PCI devices work (IDE, ethernet, the DC21285).
Olof Johansson [Tue, 23 Jul 2013 02:58:02 +0000 (19:58 -0700)]
Merge tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, imx fixes for 3.11:
- A few device tree source fixes regarding pinctrl, clock, and pwm
backlight.
- Fixes imx28 and imx51 audio driver failure caused by sgtl5000 codec
driver change by supplying the correct clock for codec.
- imx6q emi_sel clock muxing and imx6q-iomuxc-gpr macro fixes
* tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: Pass a real clock to the codec
ARM i.MX53: mba53: Fix PWM backlight DT node
ARM: imx: fix vf610 enet module clock selection
ARM: mxs: saif0 is the clock provider to sgtl5000
ARM: i.MX6Q: correct emi_sel clock muxing
ARM i.MX6Q: Fix IOMUXC GPR1 defines for ENET_CLK_SEL and IPU1/2_MUX
ARM: i.MX27: Typo fix
ARM: imx27: Fix documentation for SPLL clock
ARM i.MX53: Fix UART pad configuration
Olof Johansson [Tue, 23 Jul 2013 02:53:29 +0000 (19:53 -0700)]
Merge tag 'omap-for-v3.11/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap fixes mostly to deal with the dropping of platform data for omap4,
and to make v7_defconfig bootable on omap4 SDP with nfsroot.
* tag 'omap-for-v3.11/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Provide alias to USB PHY clock
ARM: dts: Add missing vmmc2 regulator for twl
ARM: multi_v7: Enabled omap4430 sdp nfsroot
Olof Johansson [Tue, 23 Jul 2013 02:50:11 +0000 (19:50 -0700)]
Merge tag 'davinci-fixes-for-v3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
From Sekhar Nori:
DaVinci fixes for v3.11-rc2
The pull request includes fixes for sparse warnings, defconfig changes to
enable DMA usage on peripherals and removal of a duplicated include file.
* tag 'davinci-fixes-for-v3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: defconfig: enable EDMA driver
ARM: davinci: make file local variables static
ARM: edma: remove duplicated include from edma.c
Some of the ARM_ERRATA selection is not done in the initial SOC support
patches. This patch selects 2 new ARM_ERRATA's and removes one which was
actually fixed.
Signed-off-by: Srinivas Kandagatla <[email protected]>
[olof: reorder new errata entries] Signed-off-by: Olof Johansson <[email protected]>
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
This patch fixes a bug in pinctrl setup of serial2 device, Some of the
pins in the pinctrl node of serial2 do not belong to that
pin-controller. This patch divides them in the pins into there
respective pin controller nodes.
Without this patch serial on StiH416-B2000 Board will not work as it
fails with:
"st-pinctrl pin-controller-rear.3: failed to get pin(99) name
st-pinctrl pin-controller-rear.3: maps: function serial2 group serial2-0
num 4
pinconfig core: failed to register map default (3): no group/pin given"
Merge tag 'trace-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes and cleanups from Steven Rostedt:
"This contains fixes, optimizations and some clean ups
Some of the fixes need to go back to 3.10. They are minor, and deal
mostly with incorrect ref counting in accessing event files.
There was a couple of optimizations that should have perf perform a
bit better when accessing trace events.
And some various clean ups. Some of the clean ups are necessary to
help in a fix to a theoretical race between opening a event file and
deleting that event"
* tag 'trace-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Kill the unbalanced tr->ref++ in tracing_buffers_open()
tracing: Kill trace_array->waiter
tracing: Do not (ab)use trace_seq in event_id_read()
tracing: Simplify the iteration logic in f_start/f_next
tracing: Add ref_data to function and fgraph tracer structs
tracing: Miscellaneous fixes for trace_array ref counting
tracing: Fix error handling to ensure instances can always be removed
tracing/kprobe: Wait for disabling all running kprobe handlers
tracing/perf: Move the PERF_MAX_TRACE_SIZE check into perf_trace_buf_prepare()
tracing/syscall: Avoid perf_trace_buf_*() if sys_data->perf_events is empty
tracing/function: Avoid perf_trace_buf_*() if event_function.perf_events is empty
tracing: Typo fix on ring buffer comments
tracing: Use trace_seq_puts()/trace_seq_putc() where possible
tracing: Use correct config guard CONFIG_STACK_TRACER
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
"These are fixes collected over the last week, they fixes several
problems caused by the x86_pkg_temp_thermal introduced in 3.11-rc1.
Specifics:
- the x86_pkg_temp_thermal driver causes crash on systems with no
package MSR support as there is a bug in the logic to check
presence of DTHERM and PTS feature together. Added a change so
that when there is no PTS support, module doesn't get loaded.
- fix krealloc() misuse in pkg_temp_thermal_device_add().
If krealloc() returns NULL, it doesn't free the original. Thus if
we want to exit because of the krealloc() failure, we must make
sure the original one is freed.
- The error code path of the x86 package temperature thermal driver's
initialization routine makes an unbalanced call to
get_online_cpus(), which causes subsequent CPU offline operations,
and consequently system suspend, to permanently block in
cpu_hotplug_begin() on systems where get_core_online() returns an
error code.
Remove the extra get_online_cpus() to fix the problem"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal: Fix lockup of cpu_down()
Thermal: x86_pkg_temp: Limit number of pkg temp zones
Thermal: x86_pkg_temp: fix krealloc() misuse in in pkg_temp_thermal_device_add()
Thermal: x86 package temp thermal crash
Merge tag 'gpio-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"A first round of GPIO fixes for the v3.11 series:
- OMAP device tree boot fix
- Handle an error condition in the MSM driver
The OMAP patches have been around since around the merge window, but
since they first caused more breakage I let them boil in -next for a
while. These should be fine now"
* tag 'gpio-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
drivers: gpio: msm: Fix the error condition for reading ngpio
gpio/omap: fix build error when OF_GPIO is not defined.
gpio/omap: auto request GPIO as input if used as IRQ via DT
gpio/omap: don't create an IRQ mapping for every GPIO on DT
Merge branch 'for-3.11/drivers' of git://git.kernel.dk/linux-block
Pull block IO driver bits from Jens Axboe:
"As I mentioned in the core block pull request, due to real life
circumstances the driver pull request would be late. Now it looks
like -rc2 late... On the plus side, apart form the rsxx update, these
are all things that I could argue could go in later in the cycle as
they are fixes and not features. So even though things are late, it's
not ALL bad.
The pull request contains:
- Updates to bcache, all bug fixes, from Kent.
- A pile of drbd bug fixes (no big features this time!).
- xen blk front/back fixes.
- rsxx driver updates, some of them deferred form 3.10. So should be
well cooked by now"
* 'for-3.11/drivers' of git://git.kernel.dk/linux-block: (63 commits)
bcache: Allocation kthread fixes
bcache: Fix GC_SECTORS_USED() calculation
bcache: Journal replay fix
bcache: Shutdown fix
bcache: Fix a sysfs splat on shutdown
bcache: Advertise that flushes are supported
bcache: check for allocation failures
bcache: Fix a dumb race
bcache: Use standard utility code
bcache: Update email address
bcache: Delete fuzz tester
bcache: Document shrinker reserve better
bcache: FUA fixes
drbd: Allow online change of al-stripes and al-stripe-size
drbd: Constants should be UPPERCASE
drbd: Ignore the exit code of a fence-peer handler if it returns too late
drbd: Fix rcu_read_lock balance on error path
drbd: fix error return code in drbd_init()
drbd: Do not sleep inside rcu
bcache: Refresh usage docs
...
libata: make it clear that sata_inic162x is experimental
sata_inic162x never reached a state where it's reliable enough for
production use and data corruption is a relatively common occurrence.
Make the driver generate warning about the issues and mark the Kconfig
option as experimental.
If the situation doesn't improve, we'd be better off making it depend
on CONFIG_BROKEN. Let's wait for several cycles and see if the kernel
message draws any attention.
Mark Kettenis [Sun, 21 Jul 2013 20:44:09 +0000 (16:44 -0400)]
drm/radeon: fix combios tables on older cards
Noticed that my old Radeon 7500 hung after printing
drm: GPU not posted. posting now...
when it wasn't selected as the primary card the BIOS. Some digging
revealed that it was hanging in combios_parse_mmio_table() while
parsing the ASIC INIT 3 table. Looking at the BIOS ROM for the card,
it becomes obvious that there is no ASIC INIT 3 table in the BIOS.
The code is just processing random garbage. No surprise it hangs!
Why do I say that there is no ASIC INIT 3 table is the BIOS? This
table is found through the MISC INFO table. The MISC INFO table can
be found at offset 0x5e in the COMBIOS header. But the header is
smaller than that. The COMBIOS header starts at offset 0x126. The
standard PCI Data Structure (the bit that starts with 'PCIR') lives at
offset 0x180. That means that the COMBIOS header can not be larger
than 0x5a bytes and therefore cannot contain a MISC INFO table.
I looked at a dozen or so BIOS images, some my own, some downloaded from:
It is fairly obvious that the size of the COMBIOS header can be found
at offset 0x6 of the header. Not sure if it is a 16-bit number or
just an 8-bit number, but that doesn't really matter since the tables
seems to be always smaller than 256 bytes.
So I think combios_get_table_offset() should check if the requested
table is present. This can be done by checking the offset against the
size of the header. See the diff below. The diff is against the WIP
OpenBSD codebase that roughly corresponds to Linux 3.8.13 at this
point. But I don't think this bit of the code changed much since
then.
The patch below fixes the problem for this card.
But I don't like the blacklist, couldn't some heuristic be used instead?
The interesting thing is that the manufacturer is the same as the other card
needing the same quirk. I wonder how many different types are broken this way.
The "wrong" ps2_pdac_adj value that comes from BIOS on this card is 0x300.
====================
drm/radeon: Add primary dac adj quirk for Sapphire Radeon VE 7000 DDR
Values from BIOS are wrong, causing too bright colors.
Use default values instead.
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
The PFC pinctrl driver on sh73a0 is also regiatering a VccQ regulator for
SDHI0. However, its consumers list only included the platform-data based
SDHI device name. When booted with DT SDHI0 couldn't enable VccQ and
therefore was unusable. Fix this by adding a consumer with DT-based name.
of/irq: init struct resource to 0 in of_irq_to_resource()
It almost does not matter because most users use only the ->start member
of the struct. However if this struct is passed to a platform device
which is then added via platform_device_add() then the ->parent member is
also used.
Axel Lin [Sun, 23 Jun 2013 07:50:07 +0000 (15:50 +0800)]
of/irq: Avoid calling list_first_entry() for empty list
list_first_entry() expects the list is not empty, we need to check if list is
empty before calling list_first_entry(). Thus use list_first_entry_or_null()
instead of list_first_entry().
Grant Likely [Sat, 20 Jul 2013 01:57:39 +0000 (18:57 -0700)]
MAINTAINERS: Refactor device tree maintainership
Device tree bindings require a lot more attention than they used to.
We've got a group of volunteers willing to take over maintaining
bindings. This patch adds them to the MAINTAINERS file.
This group still needs to work out a process for maintainership and how
they are going to work together. I recommend that they set up a shared
tree on git.kernel.org that they each have commit access to similar to
the tip tree or the arm-soc tree, but it is up to them.
Grant Likely [Thu, 11 Jul 2013 10:34:12 +0000 (11:34 +0100)]
MAINTAINERS: Remove Grant Likely
Unfortunately, I'm no longer to spend the time needed on maintainership.
It is time for me to step aside and pass maintainership to other
engineers. I'm not disappearing from Linux development, but it would be
irresponsible for me to hold onto a job that I am unable to do.
v2: Leave my name on devicetree core code maintainership. Rob NAKed that
part of the patch. :)
Sami Rahman [Mon, 8 Jul 2013 18:28:55 +0000 (14:28 -0400)]
USB: cp210x: add MMB and PI ZigBee USB Device Support
Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB
devices using customized Silicon Labs' CP210x.c USB to UART bridge
drivers with PIDs: 88A4, 88A5.
USB: option: append Petatel NP10T device to GSM modems list
This patch was tested on 3.10.1 kernel.
Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
projects / linux.git / log