Chao Xie [Fri, 22 Feb 2013 00:45:17 +0000 (16:45 -0800)]
drivers/rtc/rtc-sa1100.c: move clock enable/disable to probe/remove
The original sa1100_rtc_open/sa1100_rtc_release will be called when the
/dev/rtc0 is opened or closed. In fact, these two functions will
enable/disable the clock. Disabling clock will make rtc not work. So
only enable/disable clock when probe/remove the device.
Jonghwa Lee [Fri, 22 Feb 2013 00:45:07 +0000 (16:45 -0800)]
rtc: max8997: add driver for max8997 rtc
Add an rtc driver for Maxim 8997 multifunction chip. Max8997 has rtc
module in it. and it can be used for timekeeping clock and system alarm.
It provide various operational mode those are BCD/binary, 24/12hour,
am/pm. Driver sets binary/24/ for default. Maxim 8997 also supports
SMPL(Sudden Momentary Power Loss), WTSR (Watchdog Timeout and Software
Reset).
Gregory CLEMENT [Fri, 22 Feb 2013 00:44:55 +0000 (16:44 -0800)]
arm: mvebu: add RTC support for Armada 370 and Armada XP
The Armada 370 and Armada XP Socs have the same controller that the one
used in the orion platforms. This patch updates the device tree for
these SoCs.
Laxman Dewangan [Fri, 22 Feb 2013 00:44:38 +0000 (16:44 -0800)]
drivers/rtc/rtc-tps65910.c: set irq flag to IRQF_EARLY_RESUME during irq request
All interrupt get disabled during system suspend and enabled during system
resume. The enabling/disabling of interrupt happen in sequence of
interrupt registration with framework.
Therefore, in resume, the parent interrupt of this device enabled before
the RTC irq interrupt enabled. If RTC is enabled for alarm wake and if
system wake by alarm then there is interrupt pending for RTC. In resume,
the parent interrupt get enabled before the rtc interrupt and hence ISR
get served. In ISR, it founds that rtc interrupt is disabled and so it
does not call the rtc isr handler and hence it misses the interrupt.
Setting flag for early resume so that rtc interrupt get enabled before
parent interrupt and so rtc interrupt get enabled when parent interrupt
handler check for interrupt of device and call the rtc handler if it is
there. This way it will not miss the interrupt.
Laxman Dewangan [Fri, 22 Feb 2013 00:44:36 +0000 (16:44 -0800)]
drivers/rtc/rtc-tps65910.c: remove unnecessary irq stat save and restore
The driver stores the interrupt enable register before going to suspend
and restore in resume. Also it enables alarm before going to suspend.
The driver only write the Interrupt enable register for enabling ALARM and
does not enable any other bits. So it is not require to save complete
register and enable ALARM interrupt before suspend and restore in resume.
Also ALARM interrupt already enable if alarm is enabled before going to
suspend and hence it is not require to enable explictly in suspend.
Laxman Dewangan [Fri, 22 Feb 2013 00:44:34 +0000 (16:44 -0800)]
rtc: add RTC driver for TPS80031/TPS80032
Add an RTC driver for TPS80031/TPS80032 chips by TI. This driver
supports:
- Setting and getting time and date.
- Setting and reading alarm time.
- Alarm and interrupt functionlity.
Jonghwa Lee [Fri, 22 Feb 2013 00:44:26 +0000 (16:44 -0800)]
rtc: max77686: add Maxim 77686 driver
Add a driver to support max77686 rtc. MAX77686 rtc support smpl and wtsr
mode. It has two alarm register which can be used for alarming to wake
system up. This drvier uses regmap to access its register.
Bruce Allan [Fri, 22 Feb 2013 00:44:19 +0000 (16:44 -0800)]
checkpatch: fix USLEEP_RANGE test
Do not test udelay() for a value less than 10usec when passed a variable
instead of a hard-coded number; there is no way for checkpatch to know the
value of the variable. As it is today, it will complain about variables
with alphanumeric characters plus '_', e.g. foo_bar, but not variables
with other characters, eg. foo->bar.
Florian Fainelli [Fri, 22 Feb 2013 00:44:12 +0000 (16:44 -0800)]
decompressors: make the default XZ_DEC_* config match the selected architecture
Change the defautl XZ_DEC_* config symbol to match the configured
architecture. It is perfectly legitimate to support multiple XZ BCJ
filters for different architectures (e.g.: to mount foreign squashfs/xz
compressed filesystems), it is however more natural not to select them all
by default, but only the one matching the configured architecture.
Namjae Jeon [Fri, 22 Feb 2013 00:44:08 +0000 (16:44 -0800)]
lib/parser.c: fix up comments for valid return values from match_number
match_number() has return values of -ENOMEM, -EINVAL and -ERANGE. So, for
all the functions calling match_number, the return value should include
these values. Fix up the comments to reflect the correct values.
Getting the brightness value is not critical, no need to read the actual
register value. To simplify it, just return the 'bl->props.brightness'
value. Then, lp855x_read_byte() can be removed, not used any more.
Kim, Milo [Fri, 22 Feb 2013 00:44:06 +0000 (16:44 -0800)]
backlight: lp855x_bl: support new LP8557 device
LP8557 is one of LP855x family device, but it has different register map
and initialization process. To support this device, device specific
configuration is done through the lp855x_device_config structure.
Few register definitions are fixed for better readability.
BRIGHTNESS_CTRL -> LP855X_BRIGHTNESS_CTRL
DEVICE_CTRL -> LP855X_DEVICE_CTRL
EEPROM_START -> LP855X_EEPROM_START
EEPROM_END -> LP855X_EEPROM_END
EPROM_START -> LP8556_EPROM_START
EPROM_END -> LP8556_EPROM_END
And LP8557 register definitions are added. New register function,
lp855x_update_bit() is added.
At this moment, LP855x device driver has fixed register configuration.
For example, fixed register addresses and values are set on the device
initialization. But new device of LP855x family, LP8557 has different
register map and initialization sequence. To support new device
architecture, initialization process should be changed.
Introduce new structure: lp855x_device_config
=============================================
With lp855x_device_config, device specific features are configurable.
Use configurable function calls and register addresses rather than fixed values.
Change on device initialization
===============================
In old LP855x driver architecture, the device initialization was simple.
- Just update the brightness/device control register/ROM area(optional).
In new LP855x driver architecture, two more works are added - pre_init and
post_init.
Those init functions are optional, used for new device LP8557.
New device initialization flow: generic sequence
=================================================
1) pre_init_device()
2) update the brightness register
3) update the device control register
4) update ROM area if need
5) post_init_device()
Name change
===========
Use generic name 'lp855x_configure()' instead of 'lp855x_init_registers()'.
Clearing the NSTBY bit in the control register also automatically clears
the BLEN bit. So we need to make sure to set it again during resume,
otherwise the backlight will stay off.
of_find_node_by_name() returns a node pointer with refcount incremented,
use of_node_put() on it when done.
of_find_node_by_name() will call of_node_put() against the node pass to
from parameter, thus we also need to call of_node_get(from) before calling
of_find_node_by_name().
This is an initial commit of a backlight driver, using step-up DCDC
power supplies on AS3711 PMIC. Only one mode has actually been tested,
several further modes have been implemented "dry," but disabled to avoid
accidental hardware damage. Anyone wishing to use any of those modes
will have to modify the driver.
Tested on sh73a0-based kzm9g board. Only one mode has been tested and
is enabled. That mode copies the sample code from the manufacturer.
Deviations from that code proved to be fatal for the hardware...
Jingoo Han [Fri, 22 Feb 2013 00:43:51 +0000 (16:43 -0800)]
backlight: corgi_lcd: use lcd_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using lcd_device
instead of using dev_get_drvdata with &ld->dev, so we can directly pass a
struct lcd_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:50 +0000 (16:43 -0800)]
backlight: omap1: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:49 +0000 (16:43 -0800)]
backlight: tosa: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:48 +0000 (16:43 -0800)]
backlight: corgi_lcd: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:47 +0000 (16:43 -0800)]
backlight: ams369fg06: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:46 +0000 (16:43 -0800)]
pwm_backlight: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:44 +0000 (16:43 -0800)]
backlight: aat2870: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:43 +0000 (16:43 -0800)]
backlight: lms501kf03: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:42 +0000 (16:43 -0800)]
backlight: corgi_lcd: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:41 +0000 (16:43 -0800)]
backlight: tosa: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:40 +0000 (16:43 -0800)]
backlight: vgg2432a4: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:39 +0000 (16:43 -0800)]
backlight: ams369fg06: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:38 +0000 (16:43 -0800)]
backlight: lms283gf05: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:37 +0000 (16:43 -0800)]
backlight: tdo24m: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:36 +0000 (16:43 -0800)]
backlight: ltv350qv: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:35 +0000 (16:43 -0800)]
backlight: s6e63m0: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device
Jingoo Han [Fri, 22 Feb 2013 00:43:33 +0000 (16:43 -0800)]
backlight: ld9040: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Jingoo Han [Fri, 22 Feb 2013 00:43:32 +0000 (16:43 -0800)]
backlight: l4f00242t03: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
'before_power' was used to check the previous status when resume() is
called. However, FB_BLANK_POWERDOWN was used in suspend() all the time,
so there is no need to check the previous status. Also, redundant return
variables are removed to reduce the code.
Remove unnecessary NULL deference check, because it was already checked in
ams369fg06_probe(). Also, unnecessary parentheses are removed in
ams369fg06_power_is_on().
'before_power' was used to check the previous status when resume() is
called. However, FB_BLANK_POWERDOWN was used in suspend() all the time,
so there is no need to check the previous status. Also, redundant return
variables are removed to reduce the code.
Cody P Schafer [Fri, 22 Feb 2013 00:43:13 +0000 (16:43 -0800)]
MAINTAINERS: mm: add additional include files to listing
Add gfp.h, mmzone.h, memory_hotplug.h & vmalloc.h to the "MEMORY
MANAGMENT" section so scripts/get_maintainer.pl can do a better job of
making recommendations.
get_maintainer.pl: find maintainers for removed files
For removed files, get_maintainer.pl doesn't find any maintainers (besides
the default [email protected]), as it only looks at the "+++"
lines, which are "/dev/null" for removals. Fix this by extending the
parsing to the "---" lines.
E.g. for the two line test patch below the real score maintainers will now
be found:
lib/vsprintf.c: add %pa format specifier for phys_addr_t types
Add the %pa format specifier for printing a phys_addr_t type and its
derivative types (such as resource_size_t), since the physical address
size on some platforms can vary based on build options, regardless of
the native integer type.
projects / linux.git / log