Ingo Molnar [Tue, 24 Aug 2010 08:41:33 +0000 (10:41 +0200)]
V4L/DVB: mantis: Fix IR_CORE dependency
This build bug triggers:
drivers/built-in.o: In function `mantis_exit':
(.text+0x377413): undefined reference to `ir_input_unregister'
drivers/built-in.o: In function `mantis_input_init':
(.text+0x3774ff): undefined reference to `__ir_input_register'
If MANTIS_CORE is enabled but IR_CORE is not. Add the correct
dependency.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Get rid of indirect p1275 PROM call buffer.
sparc64: Fill a missing delay slot.
sparc64: Make lock backoff really a NOP on UP builds.
sparc64: simple microoptimizations for atomic functions
sparc64: Make rwsems 64-bit.
sparc64: Really fix atomic64_t interface types.
Neil Horman [Wed, 11 Aug 2010 05:12:57 +0000 (05:12 +0000)]
3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx
If netconsole is in use, there is a possibility for deadlock in 3c59x between
boomerang_interrupt and boomerang_start_xmit. Both routines take the vp->lock,
and if netconsole is in use, a pr_* call from the boomerang_interrupt routine
will result in the netconsole code attempting to trnasmit an skb, which can try
to take the same spin lock, resulting in deadlock.
The fix is pretty straightforward. This patch allocats a bit in the 3c59x
private structure to indicate that its handling an interrupt. If we get into
the transmit routine and that bit is set, we can be sure that we have recursed
and will deadlock if we continue, so instead we just return NETDEV_TX_BUSY, so
the stack requeues the skb to try again later.
[S390] fix tlb flushing vs. concurrent /proc accesses
The tlb flushing code uses the mm_users field of the mm_struct to
decide if each page table entry needs to be flushed individually with
IPTE or if a global flush for the mm_struct is sufficient after all page
table updates have been done. The comment for mm_users says "How many
users with user space?" but the /proc code increases mm_users after it
found the process structure by pid without creating a new user process.
Which makes mm_users useless for the decision between the two tlb
flusing methods. The current code can be confused to not flush tlb
entries by a concurrent access to /proc files if e.g. a fork is in
progres. The solution for this problem is to make the tlb flushing
logic independent from the mm_users field.
* git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc: Fix config dependency problem with MPIC_U3_HT_IRQS
via-pmu: Add compat_pmu_ioctl
powerpc: Wire up fanotify_init, fanotify_mark, prlimit64 syscalls
powerpc/pci: Fix checking for child bridges in PCI code.
powerpc: Fix typo in uImage target
powerpc: Initialise paca->kstack before early_setup_secondary
powerpc: Fix bogus it_blocksize in VIO iommu code
powerpc: Inline ppc64_runlatch_off
powerpc: Correct smt_enabled=X boot option for > 2 threads per core
powerpc: Silence xics_migrate_irqs_away() during cpu offline
powerpc: Silence __cpu_up() under normal operation
powerpc: Re-enable preemption before cpu_die()
powerpc/pci: Drop unnecessary null test
powerpc/powermac: Drop unnecessary null test
powerpc/powermac: Drop unnecessary of_node_put
powerpc/kdump: Stop all other CPUs before running crash handlers
powerpc/mm: Fix vsid_scrample typo
powerpc: Use is_32bit_task() helper to test 32 bit binary
powerpc: Export memstart_addr and kernstart_addr on ppc64
powerpc: Make rwsem use "long" type
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
68328serial: check return value of copy_*_user() instead of access_ok()
synclink: add mutex_unlock() on error path
rocket: add a mutex_unlock()
ip2: return -EFAULT on copy_to_user errors
ip2: remove unneeded NULL check
serial: print early console device address in hex
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
kobject_uevent: fix typo in comments
firmware_class: fix typo in error path
kobject: Break the kobject namespace defs into their own header
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (29 commits)
ARM: imx: fix build failure concerning otg/ulpi
USB: ftdi_sio: add product ID for Lenz LI-USB
USB: adutux: fix misuse of return value of copy_to_user()
USB: iowarrior: fix misuse of return value of copy_to_user()
USB: xHCI: update ring dequeue pointer when process missed tds
USB: xhci: Remove buggy assignment in next_trb()
USB: ftdi_sio: Add ID for Ionics PlugComputer
USB: serial: io_ti.c: don't return 0 if writing the download record failed
USB: otg: twl4030: fix wrong assumption of starting state
USB: gadget: Return -ENOMEM on memory allocation failure
USB: gadget: fix composite kernel-doc warnings
USB: ssu100: set tty_flags in ssu100_process_packet
USB: ssu100: add disconnect function for ssu100
USB: serial: export symbol usb_serial_generic_disconnect
USB: ssu100: rework logic for TIOCMIWAIT
USB: ssu100: add register parameter to ssu100_setregister
USB: ssu100: remove duplicate #defines in ssu100
USB: ssu100: refine process_packet in ssu100
USB: ssu100: add locking for port private data in ssu100
USB: r8a66597-udc: return -ENOMEM if kzalloc() fails
...
David S. Miller [Tue, 24 Aug 2010 06:10:57 +0000 (23:10 -0700)]
sparc64: Get rid of indirect p1275 PROM call buffer.
This is based upon a report by Meelis Roos showing that it's possible
that we'll try to fetch a property that is 32K in size with some
devices. With the current fixed 3K buffer we use for moving data in
and out of the firmware during PROM calls, that simply won't work.
In fact, it will scramble random kernel data during bootup.
The reasoning behind the temporary buffer is entirely historical. It
used to be the case that we had problems referencing dynamic kernel
memory (including the stack) early in the boot process before we
explicitly told the firwmare to switch us over to the kernel trap
table.
So what we did was always give the firmware buffers that were locked
into the main kernel image.
But we no longer have problems like that, so get rid of all of this
indirect bounce buffering.
Besides fixing Meelis's bug, this also makes the kernel data about 3K
smaller.
It was also discovered during these conversions that the
implementation of prom_retain() was completely wrong, so that was
fixed here as well. Currently that interface is not in use.
Matt Evans [Thu, 12 Aug 2010 20:58:28 +0000 (20:58 +0000)]
powerpc: Initialise paca->kstack before early_setup_secondary
As early setup calls down to slb_initialize(), we must have kstack
initialised before checking "should we add a bolted SLB entry for our kstack?"
Failing to do so means stack access requires an SLB miss exception to refill
an entry dynamically, if the stack isn't accessible via SLB(0) (kernel text
& static data). It's not always allowable to take such a miss, and
intermittent crashes will result.
Primary CPUs don't have this issue; an SLB entry is not bolted for their
stack anyway (as that lives within SLB(0)). This patch therefore only
affects the init of secondaries.
Huge unexplained gaps in what should be an empty TCE table. It turns out
it_blocksize, the amount we want to align the next allocation to, was c0000000fe903b20. Completely bogus.
Initialise it to something reasonable in the VIO IOMMU code, and use kzalloc
everywhere to protect against this when we next add a non compulsary
field to iommu code and forget to initialise it.
Anton Blanchard [Fri, 6 Aug 2010 03:28:19 +0000 (03:28 +0000)]
powerpc: Inline ppc64_runlatch_off
I'm sick of seeing ppc64_runlatch_off in our profiles, so inline it
into the callers. To avoid a mess of circular includes I didn't add
it as an inline function.
Nathan Fontenot [Thu, 5 Aug 2010 07:42:11 +0000 (07:42 +0000)]
powerpc: Correct smt_enabled=X boot option for > 2 threads per core
The 'smt_enabled=X' boot option does not handle values of X > 2.
For Power 7 processors with smt modes of 0,1,2,3, and 4 this does
not work. This patch allows the smt_enabled option to be set to
any value limited to a max equal to the number of threads per
core.
powerpc: Silence xics_migrate_irqs_away() during cpu offline
All IRQs are migrated away from a CPU that is being offlined so the
following messages suggest a problem when the system is behaving as
designed:
IRQ 262 affinity broken off cpu 1
IRQ 17 affinity broken off cpu 0
IRQ 18 affinity broken off cpu 0
IRQ 19 affinity broken off cpu 0
IRQ 256 affinity broken off cpu 0
IRQ 261 affinity broken off cpu 0
IRQ 262 affinity broken off cpu 0
Don't print these messages when the CPU is not online.
powerpc: Silence __cpu_up() under normal operation
During CPU offline/online tests __cpu_up would flood the logs with
the following message:
Processor 0 found.
This provides no useful information to the user as there is no context
provided, and since the operation was a success (to this point) it is expected
that the CPU will come back online, providing all the feedback necessary.
Change the "Processor found" message to DBG() similar to other such messages in
the same function. Also, add an appropriate log level for the "Processor is
stuck" message.
start_secondary() is called shortly after _start and also via
cpu_idle()->cpu_die()->pseries_mach_cpu_die()
start_secondary() expects a preempt_count() of 0. pseries_mach_cpu_die() is
called via the cpu_idle() routine with preemption disabled, resulting in the
following repeating message during rapid cpu offline/online tests
with CONFIG_PREEMPT=y:
Move the cpu_die() call inside the existing preemption enabled block of
cpu_idle(). This is safe as the idle task is affined to a single CPU so the
debug_smp_processor_id() tests (from cpu_should_die()) won't trigger as we are
in a "migration disabled" region.
Anton Blanchard [Mon, 2 Aug 2010 20:39:41 +0000 (20:39 +0000)]
powerpc/kdump: Stop all other CPUs before running crash handlers
During kdump we run the crash handlers first then stop all other CPUs.
We really want to stop all CPUs as close to the fail as possible and also
have a very controlled environment for running the crash handlers, so it
makes sense to reverse the order.
Sonny Rao [Thu, 19 Aug 2010 18:08:09 +0000 (18:08 +0000)]
powerpc: Export memstart_addr and kernstart_addr on ppc64
Some modules (like eHCA) want to map all of kernel memory, for this to
work with a relocated kernel, we need to export kernstart_addr so
modules can use PHYSICAL_START and memstart_addr so they could use
MEMORY_START. Note that the 32bit code already exports these symbols.
This makes the 64-bit kernel use 64-bit signed integers for the counter
(effectively supporting 32-bit of active count in the semaphore), thus
avoiding things like overflow of the mmap_sem if you use a really crazy
number of threads
Note: Ideally the type in the structure should be atomic_long_t rather
than "long". However, there's some nasty issues with that. It needs to
be initialized statically -and- lib/rwsem.c does things like
sem->count = RWSEM_UNLOCKED_VALUE;
Now, if you mix in the fact that atomic_* types are actually structures
with one member and note typedefs of a scalar, it makes its really nasty.
So I stuck to what we did before using a long and casts for now.
Galen Seitz [Thu, 19 Aug 2010 18:15:20 +0000 (11:15 -0700)]
USB: ftdi_sio: add product ID for Lenz LI-USB
Add ftdi product ID for Lenz LI-USB, a model train interface. This
was NOT tested against 2.6.35, but a similar patch was tested with the
CentOS 2.6.18-194.11.1.el5 kernel. It wasn't clear to me what
ordering is being used in ftdi_sio.c, so I inserted the ID after another
model train entry(SPROG_II).
Andiry Xu [Mon, 9 Aug 2010 20:56:15 +0000 (13:56 -0700)]
USB: xHCI: update ring dequeue pointer when process missed tds
This patch fixes a isoc transfer bug reported by Sander Eikelenboom.
When ep->skip is set, endpoint ring dequeue pointer should be updated
when processed every missed td. Although ring dequeue pointer will also
be updated when ep->skip is clear, leave it intact during missed tds
processing may cause two issues:
1). If the very next valid transfer following missed tds is a short
transfer, its actual_length will be miscalculated;
2). If there are too many missed tds during transfer, new inserted tds
may found the transfer ring full and urb enqueue fails.
John Youn [Mon, 9 Aug 2010 20:56:11 +0000 (13:56 -0700)]
USB: xhci: Remove buggy assignment in next_trb()
The code to increment the TRB pointer has a slight ambiguity that could
lead to a bug on different compilers. The ANSI C specification does not
specify the precedence of the assignment operator over the postfix
operator. gcc 4.4 produced the correct code (increment the pointer and
assign the value), but a MIPS compiler that one of John's clients used
assigned the old (unincremented) value.
Remove the unnecessary assignment to make all compilers produce the
correct assembly.
Felipe Balbi [Wed, 11 Aug 2010 10:02:32 +0000 (13:02 +0300)]
USB: otg: twl4030: fix wrong assumption of starting state
The reset state of twl4030-usb is not sleeping, it starts
up awaken and we need to disable it if we have booted
with a disconnected cable to avoid over consumption on
the default state.
To avoid problems later, we read the current state of the
transceiver from the PHY_PWR_CTRL register. The bootloader
can, anyways, put the device to sleep before us.
ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
return ret;
}
// </smpl>
Randy Dunlap [Wed, 11 Aug 2010 19:07:13 +0000 (12:07 -0700)]
USB: gadget: fix composite kernel-doc warnings
Warning(include/linux/usb/composite.h:284): No description found for parameter 'disconnect'
Warning(drivers/usb/gadget/composite.c:744): No description found for parameter 'c'
Warning(drivers/usb/gadget/composite.c:744): Excess function parameter 'cdev' description in 'usb_string_ids_n'
Bill Pemberton [Thu, 5 Aug 2010 21:01:11 +0000 (17:01 -0400)]
USB: ssu100: add disconnect function for ssu100
Add a disconnect function to the functions of this device. The
disconnect is a call to usb_serial_generic_disconnect() so it requires
that symbol to be exported from generic.c.
Bill Pemberton [Thu, 5 Aug 2010 21:01:07 +0000 (17:01 -0400)]
USB: ssu100: remove duplicate #defines in ssu100
The ssu100 uses a TI16C550C UART so the SERIAL_ defines in this code
are duplicates of those found in serial_reg.h. Remove the defines in
ssu100.c and use the ones in the header file.
Bill Pemberton [Thu, 5 Aug 2010 21:01:06 +0000 (17:01 -0400)]
USB: ssu100: refine process_packet in ssu100
The status information does not appear at the start of each incoming
packet so the check for len < 4 at the start of ssu100_process_packet
is wrong. Remove it.
USB: io_ti: check firmware version before updating
If we can't read the firmware for a device from the disk, and yet the
device already has a valid firmware image in it, we don't want to
replace the firmware with something invalid. So check the version
number to be less than the current one to verify this is the correct
thing to do.
Jef Driesen [Mon, 9 Aug 2010 13:55:32 +0000 (15:55 +0200)]
USB: pl2303: New vendor and product id
Add support for the Zeagle N2iTiON3 dive computer interface. Since
Zeagle devices are actually manufactured by Seiko, this patch will
support other Seiko based models as well.
Ming Lei [Sat, 7 Aug 2010 08:20:35 +0000 (16:20 +0800)]
USB: serial: fix leak of usb serial module refrence count
The patch with title below makes reference count of usb serial module
always more than one after driver is bound.
USB-BKL: Remove BKL use for usb serial driver probing
In fact, the patch above only replaces lock_kernel() with try_module_get()
, and does not use module_put() to do what unlock_kernel() did, so casue leak
of reference count of usb serial module and the module can not be unloaded
after serial driver is bound with device.
This patch fixes the issue, also simplifies such things:
-only call try_module_get() once in the entry of usb_serial_probe()
-only call module_put() once in the exit of usb_serial_probe
>Try the navman driver instead. You can either add the device id to the
> driver and rebuild it, or do this before you plug the device in:
> modprobe navman
> echo -n "0x0df7 0x0900" > /sys/bus/usb-serial/drivers/navman/new_id
>
> and then plug your device in and see if that works.
I can confirm that the navman driver works with the right device IDs on
my i-gotU GT-600, which has the same device IDs. Attached is a patch
adding the IDs.
USB: isp1760: use a write barrier to ensure proper ndelay timing
The ISP1760 has some timing requirements where it has to delay a short
period after a write to a register has started. However, this delay is
from the time the write hits the USB chip (the ISP1760), not from the
time where the processor started processing the write. So on a quick
enough processor, it is sometimes possible for the write to not hit the
device before we start delaying, and we then violate the part's timing
requirements, so things stop working.
To avoid all this, insert a write barrier after the register write and
before the timing delay/register read so we can guarantee we only start
counting time after the write has hit the device.
Dan Carpenter [Thu, 12 Aug 2010 07:59:58 +0000 (09:59 +0200)]
USB: uvc_v4l2: cleanup test for end of loop
We're trying to test for the the end of the loop here. "format" is
never NULL. We don't know what "format->fcc" is because we're past the
end of the loop and I think "fmt->fmt.pix.pixelformat" comes from the
user so we don't know what that is either. It works, but it's cleaner
to just test to see if (i == ARRAY_SIZE(uvc_formats).
If xfs_map_blocks returns EAGAIN because of lock contention we must redirty the
page and not disard the pagecache content and return an error from writepage.
We used to do this correctly, but the logic got lost during the recent
reshuffle of the writepage code.
Dave Chinner [Tue, 24 Aug 2010 01:45:53 +0000 (11:45 +1000)]
xfs: don't do memory allocation under the CIL context lock
Formatting items requires memory allocation when using delayed
logging. Currently that memory allocation is done while holding the
CIL context lock in read mode. This means that if memory allocation
takes some time (e.g. enters reclaim), we cannot push on the CIL
until the allocation(s) required by formatting complete. This can
stall CIL pushes for some time, and once a push is stalled so are
all new transaction commits.
Fix this splitting the item formatting into two steps. The first
step which does the allocation and memcpy() into the allocated
buffer is now done outside the CIL context lock, and only the CIL
insert is done inside the CIL context lock. This avoids the stall
issue.
Dave Chinner [Tue, 24 Aug 2010 01:40:03 +0000 (11:40 +1000)]
xfs: Reduce log force overhead for delayed logging
Delayed logging adds some serialisation to the log force process to
ensure that it does not deference a bad commit context structure
when determining if a CIL push is necessary or not. It does this by
grabing the CIL context lock exclusively, then dropping it before
pushing the CIL if necessary. This causes serialisation of all log
forces and pushes regardless of whether a force is necessary or not.
As a result fsync heavy workloads (like dbench) can be significantly
slower with delayed logging than without.
To avoid this penalty, copy the current sequence from the context to
the CIL structure when they are swapped. This allows us to do
unlocked checks on the current sequence without having to worry
about dereferencing context structures that may have already been
freed. Hence we can remove the CIL context locking in the forcing
code and only call into the push code if the current context matches
the sequence we need to force.
By passing the sequence into the push code, we can check the
sequence again once we have the CIL lock held exclusive and abort if
the sequence has already been pushed. This avoids a lock round-trip
and unnecessary CIL pushes when we have racing push calls.
The result is that the regression in dbench performance goes away -
this change improves dbench performance on a ramdisk from ~2100MB/s
to ~2500MB/s. This compares favourably to not using delayed logging
which retuns ~2500MB/s for the same workload.
Dave Chinner [Tue, 24 Aug 2010 01:46:31 +0000 (11:46 +1000)]
xfs: dummy transactions should not dirty VFS state
When we need to cover the log, we issue dummy transactions to ensure
the current log tail is on disk. Unfortunately we currently use the
root inode in the dummy transaction, and the act of committing the
transaction dirties the inode at the VFS level.
As a result, the VFS writeback of the dirty inode will prevent the
filesystem from idling long enough for the log covering state
machine to complete. The state machine gets stuck in a loop issuing
new dummy transactions to cover the log and never makes progress.
To avoid this problem, the dummy transactions should not cause
externally visible state changes. To ensure this occurs, make sure
that dummy transactions log an unchanging field in the superblock as
it's state is never propagated outside the filesystem. This allows
the log covering state machine to complete successfully and the
filesystem now correctly enters a fully idle state about 90s after
the last modification was made.
Stuart Brodsky [Tue, 24 Aug 2010 01:46:05 +0000 (11:46 +1000)]
xfs: ensure f_ffree returned by statfs() is non-negative
Because of delayed updates to sb_icount field in the super block, it
is possible to allocate over maxicount number of inodes. This
causes the arithmetic to calculate a negative number of free inodes
in user commands like df or stat -f.
Since maxicount is a somewhat arbitrary number, a slight over
allocation is not critical but user commands should be displayed as
0 or greater and never go negative. To do this the value in the
stats buffer f_ffree is capped to never go negative.
[ Modified to use max_t as per Christoph's comment. ]
Dave Chinner [Tue, 24 Aug 2010 01:44:56 +0000 (11:44 +1000)]
xfs: handle negative wbc->nr_to_write during sync writeback
During data integrity (WB_SYNC_ALL) writeback, wbc->nr_to_write will
go negative on inodes with more than 1024 dirty pages due to
implementation details of write_cache_pages(). Currently XFS will
abort page clustering in writeback once nr_to_write drops below
zero, and so for data integrity writeback we will do very
inefficient page at a time allocation and IO submission for inodes
with large numbers of dirty pages.
Fix this by only aborting the page clustering code when
wbc->nr_to_write is negative and the sync mode is WB_SYNC_NONE.
Writeback is not terminating in background writeback if ->writepage is
returning with wbc->nr_to_write == 0, resulting in sub-optimal single page
writeback on XFS.
Fix the write_cache_pages loop to terminate correctly when this situation
occurs and so prevent this sub-optimal background writeback pattern. This
improves sustained sequential buffered write performance from around
250MB/s to 750MB/s for a 100GB file on an XFS filesystem on my 8p test VM.
Dave Chinner [Tue, 24 Aug 2010 01:42:30 +0000 (11:42 +1000)]
xfs: fix untrusted inode number lookup
Commit 7124fe0a5b619d65b739477b3b55a20bf805b06d ("xfs: validate untrusted inode
numbers during lookup") changes the inode lookup code to do btree lookups for
untrusted inode numbers. This change made an invalid assumption about the
alignment of inodes and hence incorrectly calculated the first inode in the
cluster. As a result, some inode numbers were being incorrectly considered
invalid when they were actually valid.
The issue was not picked up by the xfstests suite because it always runs fsr
and dump (the two utilities that utilise the bulkstat interface) on cache hot
inodes and hence the lookup code in the cold cache path was not sufficiently
exercised to uncover this intermittent problem.
Fix the issue by relaxing the btree lookup criteria and then checking if the
record returned contains the inode number we are lookup for. If it we get an
incorrect record, then the inode number is invalid.
Dave Chinner [Tue, 24 Aug 2010 01:42:41 +0000 (11:42 +1000)]
xfs: ensure we mark all inodes in a freed cluster XFS_ISTALE
Under heavy load parallel metadata loads (e.g. dbench), we can fail
to mark all the inodes in a cluster being freed as XFS_ISTALE as we
skip inodes we cannot get the XFS_ILOCK_EXCL or the flush lock on.
When this happens and the inode cluster buffer has already been
marked stale and freed, inode reclaim can try to write the inode out
as it is dirty and not marked stale. This can result in writing th
metadata to an freed extent, or in the case it has already
been overwritten trigger a magic number check failure and return an
EUCLEAN error such as:
Filesystem "ram0": inode 0x442ba1 background reclaim flush failed with 117
Fix this by ensuring that we hoover up all in memory inodes in the
cluster and mark them XFS_ISTALE when freeing the cluster.
Dave Chinner [Tue, 24 Aug 2010 01:42:52 +0000 (11:42 +1000)]
xfs: unlock items before allowing the CIL to commit
When we commit a transaction using delayed logging, we need to
unlock the items in the transaciton before we unlock the CIL context
and allow it to be checkpointed. If we unlock them after we release
the CIl context lock, the CIL can checkpoint and complete before
we free the log items. This breaks stale buffer item unlock and
unpin processing as there is an implicit assumption that the unlock
will occur before the unpin.
Also, some log items need to store the LSN of the transaction commit
in the item (inodes and EFIs) and so can race with other transaction
completions if we don't prevent the CIL from checkpointing before
the unlock occurs.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
netfilter: fix CONFIG_COMPAT support
isdn/avm: fix build when PCMCIA is not enabled
header: fix broken headers for user space
e1000e: don't check for alternate MAC addr on parts that don't support it
e1000e: disable ASPM L1 on 82573
ll_temac: Fix poll implementation
netxen: fix a race in netxen_nic_get_stats()
qlnic: fix a race in qlcnic_get_stats()
irda: fix a race in irlan_eth_xmit()
net: sh_eth: remove unused variable
netxen: update version 4.0.74
netxen: fix inconsistent lock state
vlan: Match underlying dev carrier on vlan add
ibmveth: Fix opps during MTU change on an active device
ehea: Fix synchronization between HW and SW send queue
bnx2x: Update bnx2x version to 1.52.53-4
bnx2x: Fix PHY locking problem
rds: fix a leak of kernel memory
netlink: fix compat recvmsg
netfilter: fix userspace header warning
...
Linus Torvalds [Tue, 24 Aug 2010 01:29:18 +0000 (18:29 -0700)]
Merge branch 'for-upstream/pvhvm' of git://xenbits.xensource.com/people/ianc/linux-2.6
* 'for-upstream/pvhvm' of git://xenbits.xensource.com/people/ianc/linux-2.6:
xen: pvhvm: make it clearer that XEN_UNPLUG_* define bits in a bitfield
xen: pvhvm: rename xen_emul_unplug=ignore to =unnnecessary
xen: pvhvm: allow user to request no emulated device unplug
Linus Torvalds [Tue, 24 Aug 2010 01:28:24 +0000 (18:28 -0700)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
setlocalversion: Ignote SCMs above the linux source tree
makefile: not need to regenerate kernel.release file when make kernelrelease
fixes for using make 3.82
kconfig: fix segfault when detecting recursive dependency
kconfig: fix savedefconfig with choice marked optional
Linus Torvalds [Tue, 24 Aug 2010 01:28:03 +0000 (18:28 -0700)]
Merge branch 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (33 commits)
drm/radeon/kms: fix typo in radeon_compute_pll_gain
drm/radeon/kms: try to detect tv vs monitor for underscan
drm/radeon/kms: fix sideport detection on newer rs880 boards
drm/radeon: fix passing wrong type to gem object create.
drm/radeon/kms: set encoder type to DVI for HDMI on evergreen
drm/radeon/kms: add back missing break in info ioctl
drm/radeon/kms: don't enable MSIs on AGP boards
drm/radeon/kms: fix agp mode setup on cards that use pcie bridges
drm: move dereference below check
drm: fix end of loop test
drm/radeon/kms: rework radeon_dp_detect() logic
drm/radeon/kms: add missing asic callback assignment for evergreen
drm/radeon/kms/DCE3+: switch pads to ddc mode when going i2c
drm/radeon/kms/pm: bail early if nothing's changing
drm/radeon/kms/atom: clean up dig atom handling
drm/radeon/kms: DCE3/4 transmitter fixes
drm/radeon/kms: rework encoder handling
drm/radeon/kms: DCE3/4 AdjustPixelPll updates
drm/radeon: Fix stack data leak
drm/radeon/kms: fix GTT/VRAM overlapping test
...
Sven Eckelmann [Sat, 21 Aug 2010 12:18:10 +0000 (14:18 +0200)]
Staging: batman-adv: Don't write in not allocated packet_buff
Each net_device in a system will automatically managed as a possible
batman_if and holds different informations like a buffer with a prepared
originator messages. To reduce the memory usage, the packet_buff will
only be allocated when the interface is really added/enabled for
batman-adv.
The function to update the hw address information inside the packet_buff
just assumes that the packet_buff is always initialised and thus the
kernel will just oops when we try to change the hw address of a not
already fully enabled interface.
We must always check if the packet_buff is allocated before we try to
change information inside of it.
Sven Eckelmann [Sat, 21 Aug 2010 12:18:09 +0000 (14:18 +0200)]
Staging: batman-adv: Don't use net_dev after dev_put
dev_put allows a device to be freed when all its references are dropped.
After that we are not allowed to access that information anymore. Access
to the data structure of a net_device must be surrounded a dev_hold
and ended using dev_put.
batman-adv adds a device to its own management structure in
hardif_add_interface and will release it in hardif_remove_interface.
Thus it must hold a reference all the time between those functions to
prevent any access to the already released net_device structure.
Sven Eckelmann [Sat, 21 Aug 2010 12:18:08 +0000 (14:18 +0200)]
Staging: batman-adv: Create batman_if only on register event
We try to get all events for all net_devices to be able to add special
sysfs folders for the batman-adv configuration. This also includes such
events like NETDEV_POST_INIT which has no valid kobject according to v2.6.32-rc3-13-g7ffbe3f. This would create an oops in that situation.
It is enough to create the batman_if only on NETDEV_REGISTER events
because we will also receive those events for devices which already
existed when we registered the notifier call.
Marek Lindner [Mon, 9 Aug 2010 21:56:42 +0000 (23:56 +0200)]
Staging: batman-adv: fix own mac address detection
Earlier batman-adv versions would only create a batman_if struct after
a corresponding interface had been activated by a user. Now each
existing system interface has a batman_if struct and has to be checked
by verifying the IF_ACTIVE flag.
Marek Lindner [Mon, 9 Aug 2010 21:56:41 +0000 (23:56 +0200)]
Staging: batman-adv: always reply batman icmp packets with primary mac
When receiving an batman icmp echo request or in case of a time-to-live
exceeded batman would reply with the mac address of the outgoing
interface which might be a secondary interface. Because secondary
interfaces are not globally known this might lead to confusion.
Now, replies are sent with the mac address of the primary interface.
Marek Lindner [Mon, 9 Aug 2010 21:56:40 +0000 (23:56 +0200)]
Staging: batman-adv: fix batman icmp originating from secondary interface
If a batman icmp packet had to be routed over a secondary interface
at the first hop, the mac address of that secondary interface would
be written in the 'orig' field of the icmp packet. A node which is
more than one hop away is not aware of the mac address because
secondary interfaces are not flooded through the whole mesh and
therefore can't send a reply.
This patch always sends the mac address of the primary interface
in the 'orig' field of the icmp packet.
Marek Lindner [Mon, 9 Aug 2010 21:56:39 +0000 (23:56 +0200)]
Staging: batman-adv: unify orig_hash_lock spinlock handling to avoid deadlocks
The orig_hash_lock spinlock always has to be locked with IRQs being
disabled to avoid deadlocks between code that is being executed in
IRQ context and code that is being executed in non-IRQ context.
Sven Eckelmann [Mon, 9 Aug 2010 21:56:38 +0000 (23:56 +0200)]
Staging: batman-adv: Fix merge of linus tree
Greg Kroah-Hartman merged Linus 2.6.36 tree in e9563355ac1175dd3440dc2ea5c28b27ed51a283 with his staging tree.
Different parts of the merge conflicts were resolved incorrectly and may
result in an abnormal behavior.
Fix a compile warning by initializaing lblk. Since FTL_Get_Block_Index()
returns BAD_BLOCK if it doesn't find the logical block number, lblk
number is initizalized to BAD_BLOCK.
projects / linux.git / log